Jorjin Technologies WG7831DELF Wireless module User Manual 1

Download:
Mirror Download [FCC.gov]
Document ID	2564477
Application ID	12oXa1+/EpwY7VaLviscuA==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	155.66kB (1945762 bits)
Date Submitted	2015-03-24 00:00:00
Date Available	2015-09-20 00:00:00
Creation Date	2017-10-10 17:18:33
Producing Software	GPL Ghostscript 9.18
Document Lastmod	2017-10-10 17:18:33
Document Title	投影片 1
Document Creator	Microsoft® PowerPoint® 2010
Document Author:	tedchang

a module solution provider
Operating User Manual
WG7831DELF
a module solution provider
Software lnstallation
(1) Executive TI Wireless Tools HDK2.0.exe, met process of
following screen , please fill in
Customer name = Random
License Key = 644509802
Others Were to select the preset
a module solution provider
Evaluation Board Description - 1
Jumper insertion position for the red box
a module solution provider
Evaluation Board Description - 2
BT Test
Connection USB
WIFI Test
Connection USB
a module solution provider
Evaluation Board Description - 3
BT ON : R28
BT OFF : R31
WIFI ON : R29
WIFI OFF : R32
a module solution provider
WG7831DELF
Reference Schematics
a module solution provider
COM PORT Setting
1. Install TI Wireless Tools
2. When the hardware is connected to
the PC,
it is possible to find the port number for
communication.
Under the Device Manager, select Ports
(Com & LPT).
3. Run “RTTT” to start WiFi test software.
The USB ports are Com7 and Com8. Normally, the first
port, Com7, is the communication port, while the
next port, Com8, is the debug port.
a module solution provider
(1) Select
WL18XX
WIFI RTTT Setting – 1
(2) SET COM PORT
(3) SET Baud Rate ( 921600 )
(4) SET Board Type : HDK
a module solution provider
WIFI RTTT Setting – 2
Set file path
Firmware file : C:\Program Files (x86)\Texas Instruments\Wireless Tools\RTTT\Clients\TrioScope\18xx\wl18xx-fw-mc.bin
INI file : C:\Program Files (x86)\Texas Instruments\Wireless Tools\RTTT\Clients\TrioScope\18xx\INI Files\WL8_INI_2ANT.ini
TS DLL : C:\Program Files (x86)\Texas Instruments\Wireless Tools\RTTT\Clients\TrioScope\18xx\ts18x.dll
a module solution provider
WIFI RTTT Setting – 3
Click Connect
Connected without FW
a module solution provider
WIFI RTTT Setting – 4
Click “Load” to download Firmware
Download Success
a module solution provider
WIFI RTTT Setting – 5
Select TX or RX
Set channel
Select Channel
BW
Select Modulation
and data rate
Set ANT
Set Power
Switch TX ON/OFF
a module solution provider
WIFI RTTT Setting – 6
NOTE: Chain 1 Express DUT ANT2,
Chain 2 EXpressDUT ANT1
Select dBm, Do not select dBPsat
Click SoC Limits, Power Limit Will be
locked the Dut settings. Power set
30dBm
a module solution provider
BT HCI Tester Setting – 1
(1) Execute HCI_Tester
(2) Select View  Options
(3) SET COM PORT
and Baud Rate
a module solution provider
BT HCI Tester Setting – 2
(1) Add NEW XML file
a module solution provider
BT HCI Tester Setting – 3
(1) Select NEW
(3) Select “ServicePack_18xx_3P1.xml”
(2) Select directory
a module solution provider
BT HCI Tester Setting – 4
(1) File  Open, Select “ServicePack_18xx_3p1_switch3w_Xtal.txt”
(2) Select Execute Scripts
(3) All instructions execute in sequence automatically
a module solution provider
灣NCC符合性聲明
經型式認證合格之低 率射頻電機，非經許 ，公司
自變更頻率
大 率或變更原設計之特性及 能
商號或使用者均不得擅
低 率射頻電機之使用不得影響飛航安 及 擾合法通信；經發現有 擾現象
時，應立即停用，並改善至無 擾時方得繼續使用 前項合法通信，指依電信
法規定作業之無線電通信 低 率射頻電機須忍受合法通信或工業 科學及醫
療用電波輻射性電機設備之 擾
Note: 系統廠商應於
(NCC ID) 字樣
上標示
本產品
含射頻模組:
XXXyyyLPDzzzz-x
a module solution provider
Regulatory information/warning
Manual Information to the End User
The OEM integrator has to be aware not to provide information to the end user regarding how to
i stall or re o e this RF odule i the user’s a ual of the e d product hich i tegrates this
module. The end user manual shall include all required regulatory information/warning as show in
this manual.
Federal Communication Commission Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one of the following
measures:
a module solution provider
Regulatory information/warning
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV technician for help.
 Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.
 This transmitter must not be co-located or operating in conjunction with any other antenna
or transmitter.
a module solution provider
Regulatory information/warning
Industry Canada Statement
This device complies with Industry Canada license-exempt RSS standard(s). Operation is
subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause
undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils
radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d'en compromettre le fonctionnement."
 CAN ICES-3(B)/ NMB-3(B)
Radiation Exposure Statement
This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance
20 cm between the radiator & your body.
a module solution provider
Regulatory information/warning
End Product Labeling
When the module is installed in the host device, the FCC/IC ID label must be visible through
a window on the final device or it must be visible when an access panel, door or cover is
easily re-moved. If not, a second label must be placed on the outside of the final device that
contains the following text: Co tai s FCC ID: WS2-WG
DELF Co tai s IC:
AWG
DELF
The grantee's FCC ID/IC ID can be used only when all FCC/IC compliance requirements are
met.
This device is intended only for OEM integrators under the following conditions:
(1) The antenna must be installed such that 20 cm is maintained between the antenna and
users,
(2) The transmitter module may not be co-located with any other transmitter or antenna.
(3) The Chip antenna with -2.46 dBi gain was verified in the conformity testing. Radiated
transmit power must be equal to or lower than that specified in the FCC/IC Grant of
Equipment Authorization for FCC ID: WS2-WG7831DELF and IC: 10462A-WG7831DELF. A
separate approval is required for all other antenna type, or higher gain antenna.
a module solution provider
Regulatory information/warning
In the event that these conditions cannot be met (for example certain laptop configurations
or co-location with another transmitter), then the FCC/IC authorization is no longer
considered valid and the FCC ID/IC ID cannot be used on the final product. In these
circumstances, the OEM integrator will be responsible for re-evaluating the end product
(including the transmitter) and obtaining a separate FCC/IC authorization.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Encryption                      : Standard V4.4 (128-bit)
User Access                     : Print, Extract, Print high-res
Language                        : zh-TW
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
Format                          : application/pdf
Creator                         : tedchang
Title                           : 投影片 1
Create Date                     : 2015:03:12 13:59:30+08:00
Creator Tool                    : Microsoft® PowerPoint® 2010
Modify Date                     : 2015:03:20 13:39+08:00
Metadata Date                   : 2015:03:20 13:39+08:00
Producer                        : Microsoft® PowerPoint® 2010
Document ID                     : uuid:5c487733-1dd1-4b8e-a820-d01da6794535
Instance ID                     : uuid:af1edf25-24d6-4039-8ae6-08855e5bf48f
Page Count                      : 23
Author                          : tedchang

EXIF Metadata provided by EXIF.tools