Junlan Electronic ITSB350 Bluetooth Soundbase User Manual ITSB 340 Manual 012215 lores

Shenzhen Junlan Electronic Ltd Bluetooth Soundbase ITSB 340 Manual 012215 lores

User Manual

2.1CH TV Stand Bluetooth Sound Base SpeakerMODEL:ITSB-3501 X Remote Control1 X Instruction Manual1 X RCA Cable1 X 3.5mm Aux In CableITSB-350ITSB-350Press the button on the unit or press the SOURCE button on the remote control repeatedly until "BT"appears on display.optical in. 14Optical-InFCC Warning: Changes or modifications not expressly approved by the party responsible for compliancecould void the user's authority to operate the equipment.NOTE: This equipment has been tested and found to comply with the limits for aClass B digital device, pursuant to Part 15 of the FCC Rules. These limits aredesigned to provide reasonable protection against harmful interference in aresidential installation. This equipment generates, uses and can radiate radiofrequency energy and, if not installed and used in accordance with theinstructions, may cause harmful interference to radio communications. However,there is no guarantee that interference will not occur in a particular installation.If this equipment does cause harmful interference to radio or television reception,which can be determined by turning the equipment off and on, the user isencouraged to try to correct the interference by one or more of the followingmeasures:-- Reorient or relocate the receiving antenna.-- Increase the separation between the equipment and receiver.-- Consult the dealer or an experienced radio/TV technician for help.RF Exposure StatementTo maintain compliance with FCC’s RF Exposure guidelines, This equipment should be installed and operated with minimum distance between 20cm the radiator your body: Use only the supplied antenna.-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.PLAYING AUDIO VIA OPTICAL-IN SOURCE TV; DVD player; BD player... etc.Rear view of the unit2. Power on the unit as previous procedures. 3. Press the button on the unit or press the SOURCE button on the Remote Control repeatedly until "OPTI" appears on display.4. Power on the connected external player and start playback the Music as usual.1. Connect the Optical out jack from the external audio Player (such like TV, DVD Player BD Player …etc.) to the OPTICAL IN jack on the top of unit by the Optical Connection Optical Connection Cable ( not supplied )Cable (not supplied) as the figure below: ( F or PCM format only )Turn on the digital audio output and set it to PCM (Plus Code Modulation) type similar to the follows figure:BassTrebleBalanceSelect Move MENU ExitSound Mode StandardSurround OffAVL OffAudio Language EnglishPicture Time Setup Lock OffAudioAudioDigital Output PCMDigital Output PCMOPTICALFRONT VIEW12345 6 7 8 9 10TOP VIEWREAR VIEW12. AUX IN JACKS(L/R)13. OPTICAL IN JACK14. ANTENNA WIRE OPTIC ALOPTICAL11 12 13 1411. DC IN JACK1. SPEAKER4. POWER Button5. SOURCE Button8. TUNE UP/NEXT Button9. VOLUME DOWN Button10. VOLUME UP Button2. DISPLAY3. REMOTE SENSOR6. PLAY/PAUSE/PAIR Button7. TUNE DOWN/PREVIOUS Button9. MO/ST(Mono/Stereo) Button3. SOURCE Button4. PAIR Button2. VOL(volume)- Button6. TUNE- Button12. TUNE+ Button5. EQ (equalizer) Button 7. Button8. FM SCAN Button13. PRE/RECALL ButtonSTANDBYPAIR12345891011TUNE- TUNE+MO/ST67121311. VOL(volume)+ ButtonFM SCAN10. MUTE ButtonPRE/RECALL8. This product contains a coin/button cell battery. If the coin/button cell battery is swallowed, itcan cause severe internal burn in just 2 hours and can lead to death. Keep new and used batteries away from children. If the battery compartment does not close securely, stop using and keep it away from children. If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.Folloe these precautions when using a battery in this device:1. Use only the size and type of battery specified.2. Be sure to follow the correct polarity when installing the battery as indicated in the batterycompartment. A reversed battery may cause damage to the device.3. Do not mix different types of batteries together (e.g. Alkaline and Carbon-zinc ) or old batteries with fresh ones.4. If the batteries in the device are consumed or device is not to be used for a long period of time, remove the batteries to prevent damage or injury from possible battery leakage.5. Do not try to recharge the battery not intended to be recharged; it can overheat and rupture.( Follow battery manufacturer's instructions.)6. The batteries shall not be exposed to excessive heat such as sunshine, fire or the like.7. Clean the battery contacts and also those of the device prior to battery installation.6) If the available FM station is stereo, the unit will plays it in stereo mode automatically. If the reception is no good, press the MO/ST button on the Remote Control to switch it to Mono mode. Press again to turn back to Stereo mode. listen the desired preset channels.To store the band automatically, press FM SCAN button on remote control , the unit will scan all available band and store automatically.then stop and play).to search the specificavailable band back and forth 4) 5) After finishing scanning, press "PRE/RECALL" button on remote control repeatedly to select and2) Press the button on the unit or press the SOURCE button on the Remote Control repeatedly until FM frequency appears on display.3) Press /TUNE- or /TUNE+ button on remote control(or press or button on the unit) repeatedly band.automatically the Press and hold the TUNE - or TUNE + button on remote control (or press and hold the or button on the unit), the unit will search The TV STAND SOUND BASEthe TV STAND SOUND BASEPress the button on the unit or press the SOURCE button on the remote control repeatedly until "BT"appears on display.the TV STAND SOUND BASEITSB-350ITSB-350ITSB-350ITSB-350whileplaying, press "PAIR" Button onremote control or press and hold the Button on the unit to cut off current pairing, then try to connect the other BT device following above steps. If you want to connect another BT device~ Press thePress the /TUNE + or /TUNE - button to skip the tracks. ~ button on the remote control ~ Press the EQ button on the remote control to set to JAZZ, POP, ROCK, CLAS and NORM mode.or press the button on the unit to pause, press again to resume.OPTICAL(DVD or VCR...etc)redwhite1. Connect the Aux out jacks from the external audio player (such like DVD player, VCR …etc.) to the AUX IN jacks on the rear of the unit by the supplied RCA connection cable as the figure below:2. Connect the unit to the power as previous procedures. 3. Press the Standby ( ) button on the unit or Remote Control to power on the unit.4. Press the button on the unit or press the SOURCE button on the Remote Control repeatedly until "AUX" appears on display.5. Power on the connected external player and start playback music as usual.or +correct source appearsor -20 3Type of Optical Digital Audio in ........................................................................ PCMis a trademark on a registered trademark of BluetoothSIG Inc. All other trademarks and trade names are those of their respective owners.606

Navigation menu