Junlan Electronic RP3000BT Car DVD Player User Manual
Shenzhen Junlan Electronic Ltd Car DVD Player
Manual
Receiver System RP-3000BT (Instruction Manual) A/B/C USB AUX (BT/DVD/CD/MP3/SD/USB/AM/FM/CLOCK) BEFORE USING PLEASE READ THIS MANUAL CAREFULLY COMPATIBLE DISCS 4.72" 4.72" 4.72" 4.72" ACCESSORIES 1 X Instruction manual 1 X Remote control 1 X FM-Antenna (Pig Tail) One composite audio/video cable 6 X Mounting Screws Wire Harness for DC power and speakers DC Power extension (Red and Black wire) wires Optional AC/DC Adapter 2 X Batteries Location of Controls 17 16 15 14 13 A/B/C 12 11 USB AUX 10 Tune-/Previous button Function button Standby button Reset button (NOTE) Audio channel switch Volume - button Disc loader SD card slot USB port 10 AUX 11 Tune+ / Next button 12 Play/ Pause button 13 Eject button 14 Stop button 15 Volume+ button 16 LED display 17 Remote sensor NOTE 4:This reset button is under screw cover.when unit is frozen for some reason,remove the left side screw cover,use a paper clip and reset. DVD/USB/SD/RADIO/TV/AUX ICONS DISPLAY MOUNTING AND CUT OUT INSTRUCTIONS The 6X mounting screws are in the owner’s manual bag. Note: ·Remove screw caps and carefully take mounting covers off. ·Connect and test hareness and wiring before wiring. ·Screw the unit in place, replace screw caps. REFERENCE DRAWING FOR REAR CABINET AUX TV (OUTPUT) Automotive antenna socket (AM/FM/) Wire harness for 12V DC power and 6 speakers CVBS(2 Video output) Aux (L/R) TV audio input HDMI OUTPUT Wire harness for 12V DC power & 6 speakers guide diagram Carefully read wiring diagram: the wrong connections reversing polarity (positive and negative power wiring) can cause distortation and / or damage the power amplifiers. Basic Operations TIME SETUP 1.Press to enter standby mode, press and hold CADJ/MEMO button on the remote control to enter time setup interface. The LED display will show the default time with the hour digit flashing. 2. Press UP and down to select 12 or 24 hours mode, then press CADJ/MEMO to confirm, after confirming, the hour digit will be flashing, press UP or DOWN button to adjust hour, press CADJ/MEMO again to confirm hour. 3. Once completed, the minute digit will be flashing, then press the UP or DOWN button to adjust minute. when finished, Press CADJ/MEMO to confirm, time setting is over. MODE SHIFT 1. When in standby mode, press the power button on the unit or remote to turn on the unit. 2. Press FUNC button on the remote control or FUNC button on the unit to shift modes between bt /DVD/USB/SD/FM/AM/ TV/AUX. Note -Once the disc is loaded, the unit will automatically shift to DVD mode. BLUETOOTH 1. Press FUNC button on the remote control until " bt " appears on the screen. 2. Activate the Bluetooth connection on the external device. 3. The unit will search and reconnect to previous bluetooth device that was connected if available. If it is your first time connecting, find R " P3000BT" in your device pairing list and select it to pair and connect your device to the unit. 4. Press PREV and NEXT buttons to skip to the previous and next track.. 5. Press button to select play or pause mode. Note -Skip and play/pause functions may not be compatible with all connected bluetooth devices. DISC PLAYBACK 1.One disc is inserted, unit will automactically shift to DVD mode and begin playback. 2.Press button to eject the disc. 3.Press buttons to go through the menu and press ENTER button to confirm the selections. 4.Press PREV and NEXT button to skip to the previous or next chapter / track.. 5.Press REV and FWD buttons to search through the chapter/track backward and forward at different speed. 6. Press ANGLE button to select different camera angles that available in the disc. 7. Press SUBTITLE button to select a different subtitle language if available on the disc. 8. Press TITLE button to enter title menu. 9. Press MENU button to enter disc root menu. 10. Press OSD button to display the disc inforamtion. Note -Function mentioned above may not be available on all the discs. USB/SD CARD PLAYBACK 1. Insert USB drive or USB card into appropriate slot. 2. Press FUNC button until indicator light shows USB or SD. 3. Press buttons to go through the menu and press ENTER button to confirm the selection. Note -The USB player supports MP3/ AVI /WMA/JPEG formats. TV/AUX PLAYBACK 1. Connect your external audio device (MP3 player/cell phones, etc.) to the AUX IN 2 jack in the front of the unit with an 3.5mm audio cable (not supplied). Or connect DVD player, VCR, DVR, etc to the AUX 1 jack in the rear of the unit with the RCA audio cable. 2. Press FUNC button on the remote control until desired indicator light, either TV or AUX is highlighted. 3. Activate your external device. Note -The TV can also connected to the VIDEO OUT in the rear of the unit with an AV cable to watch video files. PLAY RADIO 1. Use function button to cycle to either FM or AM which will be shown with indicator light on LED diaplay. 2. Press and hold ( or ) button to seach stations automatically. To store a searched station, press MEMO button, the screen will diaplay the order, eg: P01, then press MEMO again to confirm. Press CH- and CH+ button to play the stored station. 3. when a station searched, press MEMO to display the storage, press CH+ or CH- to select a order, eg:select P20 as the storage position, press MEMO to confirm the position. next time, press CH+ or CH- to find P20 to play the station stored. 4.. Press MEMO button on the remote control to display on the LED the preset for selected station. 5. Press CH + and CH- buttons on the remote control to select and play the stored stations.. Note -A total of 30 AM stations and 30 FM stations can be stored into the unit's memory. - Fully extend and relocate the antenna to improve the reception. REFERENCE DIAGRAM AND KEY FOR REMOTE CONTROL 13 14 15 16 17 18 19 20 21 22 SEARCH+ SEARCH- 23 10 24 25 26 27 CADJ/ ME M O 11 28 29 12 POWER PREV TITLE NEXT MENU STOP SEARCH- CH- SETUP 10 NUMBER KEYPAD 11 CADJ/MEMO 12 A/B/C 13 EJECT DISC 14 FUNC 15 SUBTITLE 18 VOL+ 21 ENTER 16 FWD 17 19 SEARCH+ 20 22 VOL- 23 / PAIR 24 AUDIO 25 MUTE 26 REPEAT 27 TONE 28 ANGLE 29 OSD REV CH+ 1 POWER Press this button to shut off power and enter standby mode, press it again to activate. TITLE Press this button to access the DVD menu. MENU Press this button to switch the menu mode. For a DVD, press MENU to open the menu during playback. PREV Press this button to skip back to the previous selection. NEXT Press this button to skip to the next chapter/track. STOP Press this button to stop play for the current DVD or CD. Press the /ENTER button to resume playback. CH – Press this button to select last station. SETUP Press this button and the setup screen will appear if available for the current mode . SEARCHPress this button to search previous radio channal. 10. NUMBER KEYPAD Press these button to select channel 11. CADJ/MEMO Set the clock time. Press this button to store a desired station to memory. 12. A/B/C Press this button to select desired speaker channel. 13. Press this button to eject CD or DVD. Don't press to load as discs load automactically. 14. FUNC Press this button to choose between AM and FM radio modes and select the desired DVD, AUX, TV or BLUETOOTH mode. 15. SUBTITLE Press this button to select different subtitle languages if applicable. 16. FWD Press this button to play fast forward, each time it is press, the speed with which it fast forward. Continue pressing it to return back to normal playback speed. 17. REV Press this button to rewind. Each time it is pressed, the speed with which it rewinds accelerates. Conitune pressing it to return back to normal playback speed. 18. VOL+ Press this button to turn the volume up. 19. SEARCH + Press this button to search next radio channel. 20. CH + Press this button to select the next station. 21. ENTER Press this button to confirm the desired/hightlighted selection. 22. VOL – Press this button to turn the volume down. 23. /PAIR Press this button to pairing blue tooth, pause the playing track or vedio, press again to replay. 24. AUDIO Press this button to enter audio mode. 25. MUTE Press this button to turn off sound, press again to resume. 26. REPEAT For DVD or CD, press this button to repeat current chapter or track. Press it again to repeat the entire DVD or CD. 27. TONE Press this button to change audio settings, such as speakers base and treble level. 28. ANGLE Press this button to select different viewing angles if available. 29. OSD Press to show status information on the screen. For your convenience, we have enlisted some points to solve problems, you may encounter while using the TM CONNEXX RP3000BT. No Sound *Make sure the connections are secure between player and speakers. *Make sure the correct input is selected on the monitor. No Picture *Make sure the connection are secure between RP3000BT and the monitor. *Make sure the RP3000BT is in the correct mode (e.g., DVD mode) Disc does not play *Make sure the disc is loaded correctly (label side is facing up on the disc tray). *Make sure the disc is clean and not damaged. Remote controller does not work *Move any obstacles between RP3000BT and remote control. *Point the remote controller at the remote control sensor. *Check the battery. TECHNICAL SPECIFICATIONS Laser Wave length 650um Video AUTO/NTSC Frequency response 20 Hz-20KHz Signal/noise ratio >60dB Dynamic rang >60dB(1KHz) Video out output level:1vp-p/ Load impedance :75 imbalance/ negative polarity Power supply DC 12-14.4V Power consumption <55W Dimensions (WxHxD) 218(L)x185(H)x169(D)mm AM Frequency range AM 520 ~ 1710KHz FM Frequency range FM87.5 ~ 108MHz Output power 30W(RMS) 10 FCC Warning: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No XMP Toolkit : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03 Producer : Acrobat Distiller 6.0.1 (Windows) Modify Date : 2013:07:16 18:13:33+08:00 Create Date : 2010:08:26 17:36:49+08:00 Metadata Date : 2013:07:16 18:13:33+08:00 Document ID : uuid:5a19d660-1d05-448b-be85-04f0e1da0b72 Instance ID : uuid:3f0a9bf7-0f28-42ed-8147-14c2061eb9b5 Format : application/pdf Title : untitled Page Count : 12EXIF Metadata provided by EXIF.tools