Junlan Electronic TSB87043 TOWER SPEAKER with Bluetooth Wireless Technology User Manual 1

Shenzhen Junlan Electronic Ltd TOWER SPEAKER with Bluetooth Wireless Technology 1

Users manual

2WARNING:TO REDUCE THE RISK OF FIRE OR ELECTRICSHOCK, DO NOT EXPOSE THIS PRODUCT TO RAINOR MOISTURE.WARNING:TO REDUCE THE RISK OF FIRE OR ELECTRICSHOCK, AND ANNOYING INTERFERENCE, USE THERECOMMENDED ACCESSORIES ONLY.FCC NOTICE:This equipment has been tested and found to complywith the limits for a Class B digital device, pursuant topart 15 of the FCC Rules. These limits are designed toprovide reasonable protection against harmfulinterference in a residential installation. This equipmentgenerates, uses and can radiate radio frequency energyand, if no nstalled and use n accordance with theinstructions, may cause harmful interference to radiocommunications.However, there is no guarantee that interference will notoccur in a particular installation. If this equipment doescause harmful interference to radio or televisionreception, which can be determined by turning theequipment off and on, the user is encouraged to try tocorrect the interference by one or more of the followingmeasures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.FCC WARNING:To assure continued compliance, follow the attachedinstallation instructions and use only shielded cableswhen connecting to other devices. Modifications notauthorized by the manufacturer may void user`s authorityto operate this device.CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOTEMOVE COVER (OR BACK). NO USER-SERVICEABLE ARTNSIDE EFER SERVICING T UALIFIED ERVICE PERSONNEL.The lightning flash with arrowhead symbolwithin an equilateral triangle is intended to alertthe user to the presence of uninsulateddangerous voltage within the product`senclosure that may be of sufficient magnitude toconstitute a risk of electric shock to persons.The exclamation point within an equilateraltriangle is intended to alert the user to thepresence of important operating andmaintenance(servicing) instructions in theliterature accompanying the appliance.S IPSO Q. RRt d iiCAUTIONRISK OF ELECTRIC SHOCK DO NOT OPENThis equipment should be installed and operated with minimum distance 20cm between the radiator and your body.
3Before using the unit, be sure to read all operating instructions carefully. Please note that theseare general precautions and may not pertain to your unit. 1) Read these instructions. All the safety and operating instructions should be read before the product is operated.2) Keep these instructions. The safety and operating instructions should be retained for future reference.3) Heed all warnings. All warnings on the product and in the operating instructions should be adhered to.4) Follow all instructions. All operating and use instructions should be followed.5) Do not use this apparatus near water. Do not use this product near water and moisture, for example: near a bathtub, washbowl, kitchen sink or laundry tub; in a wet basement; or near a swimming pool.6) Clean only with dry cloth. Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a dry cloth for cleaning.7) Do not block any ventilation openings. Install in accordance with the manufacturer's instructions. Slots and openings in the cabinet and in the back or bottom are provided for ventilation, to ensure reliable operation of the product and to protect it from overheating. These openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug or other similar surface. This product should never be placed near or over a radiator or heat source. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer's instructions have been adhered to.8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus(including amplifiers) that produce heat.9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet .10)Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.11)Only use attachments/accessories specified by the manufacturer.12)Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. An appliance and cart combination should be moved with care. Quick stop, excessive force and uneven surfaces may cause the appliance and cart combination to overturn.13) Unplug this apparatus during lightning storms or when unused for long periods of time. To protect your product from a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the product due to lightning and power-line surges.14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture does not operate normally, or has been dropped.15) Power sourceThis product should be operated only from the type of power source indicated on the marking label.If you are not sure of the type of power supply to your home, consult your appliance dealer or localpower company. For products intended to operate from battery power, or other source, refer to theoperation instructions.16) Power lines An outside antenna system should not be located in the vicinity of overhead power lines or otherelectric light or power circuits, or where it can fall into such power lines or circuits. Wheninstalling an outside antenna system, extreme care should be taken to keep from touching suchpower lines or circuits as contact with them might be fatal.For example, this unit may not have the capability to be connected to an outdoor antenna.Portable Cart Warning
417) OverloadingDo not overload wall outlets and extension cords as this can result in a risk of fire or electric shock.18) Object and liquid entryNever push objects of any kind into the product through openings as they may touch dangerousvoltage points or short out parts that could result in fire or electric shock. Never spill or spray anytype of liquid on the product.19) Outdoor antenna groundingIf an outside antenna is connected to the product,be sure the antenna system is grounded so as toProvide some protection against voltage surges and built up static charges.Section 810 of theNational Electric Code ANSI/NFPA 70 provides information with respect to proper to groundingof the mast and supporting structure, grounding of the lead-in wire to an antenna discharge product,size of grounding conductors,location of antenna-discharge product,connection to groundingelectrodes and requirements for the grounding electrodes.Do not attempt to service this product yourself as opening or removing covers may expose you todangerous voltage or other hazards.Refer all servicing to qualified service personnel.When replacement parts are required,be sure the service technician uses replacement partsspecified by the manufacturer or those that have the same characteristics as the original parts.Unauthorized substitutions may result in fire or electric shock or other hazards.Upon completion of any service or repairs to this product,ask the service technician to performsafety checks to determine that the product is in proper operational condition.The product should be mounted to a wall or ceiling only as recommended by the manufacturer.Unplug this product from the wall outlet and refer service to qualified service personnel under thefollowing conditions.a)When the power-supply cord or plug is damaged.b)If liquid has been spilled or objects have fallen into the product.c)If the product has been exposed to rain or water.d)If the product does not operate normally by following the operating instructions.Adjust onlythose controls that are covered by the operating instructions,as an adjustment of othercontrols may result in damage and will and require extensive work by a qualified technicianto restore in the product to its normal operation.e)If the product has been dropped or the cabinet has been damaged.f)When the product exhibits a distinct change in performance-this indicates a need for service.This reminder is provided to call the CATV system installer's attention to Article 820-40 of theNEC that provides guidelines for proper grounding and,in particular,specifies that the cableground shall be connected to the grounding system of the building,as close to the point of cableentry as practical.NOTE: Refer all servicing to qualified service personnel. Servicing is required whenthe unit has been damaged in any way such as the following: the power-supply cordor plug has been damaged, liquid has been spilled into unit, the unit has beenexposed to rain or moisture, the unit has been dropped or the unit does not operate normally.25) Note to CATV system installer24) Damage requiring service23) Wall or ceiling mounting22) Safety check21) Replacement parts20) Service
1TOP PANELFRONT VIEW REAR PANEL5TUNE- / VOL-STANDBY/SOURCEAUX INTUNE+/ VOL+2345678991011121. AUX IN Jack2. /TUNE-/VOL- (Skip4. STANDBY/SOURCE Button5. (Play/Pause) Button6. RESET Button7. Remote Sensor8. Indicator9. Speakers10. FM ANT (FM wire antenna)11. LINE IN Jacks12. DC IN JackRESETLINE IN LRFM ANTDC I NDC 9V, 1.3ALOCATION OF CONTROLSbackward/Tuning down/Volume down) Button3. /TUNE+/VOL+ (Skipforward/Tuning up/Volume up) Button
1. /STANDBY Button3. VOL- (Volume Down) Button4. SOURCE Button7. (Mute) Button6. (Play/Pause) Button8. VOL+ (Volume Up) ButtonREMOTE CONTROL6RESETTUN E TUN E+- BATTERY INSTALLATION (REMOTE CONTROL)1234567892. RESET ButtonRemove and discard the insulation film as illustrated on the right.RELEASEPUSHOPENR2025C+SNFig.1 Fig.2 Fig.3First Time Use:If the button cell is drained, replace it by a new one as below:1. Push and slide out the button cell holder as Fig.1 below.2. Replace the button cell with a new CR2025 button cell as the polaritymarkings on the rear of the Remote Control as Fig.2 below.3. Close the button cell holder as Fig.3 below.5. /TUNE- (Skip backward/Tuning down Button9. /TUNE+ (Skip forward/Tuning up Button
7°30 °30Approx. 16 feetWhen there is an obstacle between the unit and the transmitter, the unit may not operate.Follow these Battery Precaution when using a battery in this device:1. Use only the size and type of battery specified.6. Do not dispose of battery in fire. Battery may explodes or leak.7. Clean the battery contacts and also those of the device prior to battery installation.BATTERY PRECAUTIONS:2. Be sure to follow the correct polarity when installing the battery as indicated in the battery compartment. A reversed battery may cause damage to the device.3. Do not mix different types of batteries together (e.g. Alkaline and Carbon-zinc) or old batteries with fresh ones.4. If the batteries in the device are consumed or the device is not to be used for a long period of time, remove the batteries to prevent damage or injury from possible battery leakage.5. Do not try to recharge the battery not intended to be recharged; it can overheat and rupture. (Follow battery manufacturer’s instructions.)8. This product contains a coin/button cell battery. If the coin/button cell battery is swallowed, it can cause severe internal burn in just 2 hours and can lead to death.Keep new and used batteries away from children. If the battery compartment does not closesecurely, stop using the product and keep it away from children.If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.NOTES:When direct sunlight, an incandescent lamp, fluorescent lamp or any other strong light shineson the REMOTE SENSOR of the unit, the operation of the remote may be unstable.EFFECTIVE DISTANCE OF REMOTE TRANSMITTER
POWER SOURCE8Connect the small plug from supplied AC/DC Adaptor to the DC IN Jack on the rear of unit then plug theAC/DC Adaptor to a wall outlet having AC 100-240V~; 50/60Hz. To AC outletAC/DC AdapterTo the DC IN jackon the rear of the unitLINE IN LRFM ANTDC I NDC 9V, 1.3ANOTES: If you will not use the unit for an extended period of time, unplug the AC/DC Adaptor from wall outlet.The AC/DC Adaptor is intended to be correctly orientated in a vertical or floor mount position. The Red Standby Indicator on the top of unit will illuminate.
OPERATION 9GENERAL OPERATION:1. Connect the supplied AC/DC Adaptor to the unit and wall outlet as previously instructed. The RedStandby Indicator on the top of unit will illuminate.2. Press and hold the STANDBY/SOURCE Button on the top of unit or press the Buttonon theRemote Control to turn on the unit from standby mode. The color of the indicator will turn tocorrespondent color. You will also hear an audible say “Power on”.3. Press the STANDBY/SOURCE Button on the top of unit or press the SOURCE Button on theRemote Control repeatedly to switch to desired playback mode. The color of the indicator will turnto correspondent with your selection (see list below):Playback Mode: Color of Indicators:BT (Bluetooth) Blue (and blinking)FM Radio GreenLINE IN Purple (Red + Blue)AUX IN Orange (Red + Green)4. During playback,Press the /Tune -/VOL – or /Tune +/VOL + buttons on the unit or the VOL +/- buttonson the Remote Control to adjust volume level as desired.Press the (MUTE) Button on the Remote Control to turn off the sound temporary, pressagain to turn it back.Press and hold the SOURCE/LED 1 Button on the top of unit to power On/Off all theDecorative LED Lights.5. When finished, press and hold STANDBY/SOURCE Button on the top of unit or press theButton the Remote Control to turn the unit to standby mode. The color of the Indicatorwill turn to Red.6. If you will not use the unit for an extended period of time, unplug the AC/DC Adaptor from wall outlet.STANDBY/STANDBY/
10BT (Bluetooth):Listen music from external BT device:BT (Bluetooth) pairing:First time use or re-pairing the unit to a new BT Device, pair as follows:1. Power on the unit as previously instructed.2. Press the STANDBY/SOURCE Button on the top of unit or press the SOURCE Button on theRemote Control repeatedly until the color of the indicator turn to Blue and blink.3. Power on the external BT Device and enter to BT searching mode. Start pairing following the onscreen instructions from the external BT Device. After paired, the Blue Indicator will stop blinking.4. If pairing is complete you may now play music with your external BT Device.5. During playback:Press the Button on the unit or Remote Control to pause, press again to resume normalplayback.Press the (MUTE) Button on the Remote Control to turn off the sound temporary, pressagain to turn it back.Press the buttons on the unit or the VOL +/- buttonson the Remote Control to adjust volume level as desired.Press and hold the buttons on the unit or press the/Tune - or /Tune + buttons on the Remote Control to skip tracks.Notes:When the external BT Device searched the unit, our model number “MHT843n” will appear onthedisplay of external BT Device.If while pairing you are asked for a code please try "0000" or "1234".Normal operation after pairing:1. Power on the external BT Device and enter to BT playback mode.2. Power on the unit and enter to BT mode as previously instructed. The color of the indicator will turnto Blue and blink.3. Wait a few seconds until the unit is automatically paired to the external BT Device. (The BlueIndicator will stop blinking).4. After pairing is complete you may now play music with your external BT Device./Tune -/VOL – or /Tune +/VOL +/Tune -/VOL – or /Tune +/VOL +
11FM Radio:1. Power on the unit as previously instructed.2. Press the STANDBY/SOURCE Button on the top of unit or press the SOURCE Button on theRemoteControl repeatedly until the color of the indicator turn to Green.3. Press and hold the /Tune -/VOL – or /Tune +/VOL + buttons on the unit or press the/Tune - or /Tune + buttons on the Remote Control to search and play the next/previousavailable FM station.4. Repeat the same procedures until the desired station was search and play.5. If you want researching the stations from beginning (87.5MHz), press the RESET Button on theunit or Remote Control then search the Radio station as point 3 above again.Antennas:This unit has a FM wire antenna on the rear of unit, which provides adequate reception in most areas.If reception is weak, unwound and extended to its full length or reassemble the other direction/locationto improve reception.
12AUX IN:Listen music from external Audio Player such like MP3 Player; Discman … etc:1. Connect one side of supplied Audio Connection Cable to the Phones Jack; Line Out Jack or AUXOut Jack on the external Audio Player.2. Connect the other side of the cable to the AUX IN Jack on the top of unit as illustrate below:3. Power on the unit as the instructed earlier.4. Press the STANDBY/SOURCE Button on the top of unit or press the SOURCE Button on theRemote Control repeatedly until the color of the indicator turn to Orange (Red + Green).5. Plays the music on the connected external Audio Player as usual. (Make sure the volume levelof the external Audio Player is in high level. Otherwise, sound from this unit may weak).Mobile PhoneConnect to the Phones; AUX Out;Line Out Jack of the external devices (Such like MP3 Player; cell phones; iPod/iPad ... etc)MP3 PlayerTU NE- / VO L-STANDB Y/SO URCEAUX INTU NE+/ V OL+RESET
13LINE IN:Listen music from external Video/Audio Player DVD Player/TV …. etc:1. Connect one side of RCA Connection Cable (not included) to the RCA audio Jacks on theexternal Video/Audio Player.2. Connect the other side of the cable to the LINE IN Jacks on the rear of unit as illustrate below:3. Power on the unit as the instructed earlier.4. Press the STANDBY/SOURCE Button on the top of unit or press the SOURCE Button on theRemote Control repeatedly until the color of the indicator turn to Purple (Red + Blue).5. Plays the video/music on the connected external Video/Audio Player as usual. (Make sure thevolume level of the external Video/Audio Player is in high level. Otherwise, sound from this unitmay weak).Line out jacks of TV/DVD player etc.LRVideoLINE IN LRFM ANTDC I NDC 9V, 1.3Awhitered
TROUBLESHOOTING GUIDEIf you are having problems with your unit, please review the guide below before requesting.SYSTEM POSSIBLE CAUSE POSSIBLE SOLUTION14The unit had not connect to AC power Connect the supplied AC/DC Adaptor to the unit and wall outletPress and hold the STANDBY/SOURCE Button on the top of unit or press the /STANDBY Button on the Remote Control to turn on the unit No powerThe unit is in standby modeVolume is set to minimum Press the /Tune +/VOL + button on the unit or the VOL + button on the Remote Control Volume level of paired/connecteddevice is in low levelNo sound Rise the volume level of thepaired/connected deviceVolume level is too highPress the /Tune -/VOL - button on the unit or the VOL - button on the Remote ControlReduce the volume level of thepaired/connected deviceSounddistortionRadio weak reception Volume level of paired/connecteddevice is too highUnwound and extended the wire antenna to its full length or reassemble the other direction/location to improve receptionRemotenot functioning The button cell in remote controlis drained Replace with new button cellBluetoothfail to pairThe external BT device is too farfrom the unit Place the external BT deviceclose to the unit The external BT device hadNOT paired to the unit Pair the external BT device tothe unit as page 10 indicates
GENERAL SPECIFICATIONSPACKAGE INCLUDES:Power source................................................................................DC 9V 1300mASpeaker...................................................................................................8W x 4ohm per channel1 x Owner's Manual1 x AC/DC Adapter15Audio Power..........................................................................5W per channel (Total 10 W, RMS)FM radio frequency...............................................................................................87.5-108.0MHzBluetooth version....................................................................................................................V4.2Bluetooth working range............................................................................ 32 feet in open area≤1 x Audio Connection Cable with 3.5mm plugs1 x Remote Control (Uses 1 x CR2025 Button Cell, included)(Input: 100-240V~ 50/60Hz 0.5A Output: 9V 1300mA)

Navigation menu