Junlan Electronic TSB87043 TOWER SPEAKER with Bluetooth Wireless Technology User Manual 1
Shenzhen Junlan Electronic Ltd TOWER SPEAKER with Bluetooth Wireless Technology 1
Users manual
2
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN
OR MOISTURE.
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, AND ANNOYING INTERFERENCE, USE THE
RECOMMENDED ACCESSORIES ONLY.
FCC NOTICE:
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful
interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy
and, if no nstalled and use n accordance with the
instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does
cause harmful interference to radio or television
reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and
receiver.
Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV
technician for help.
FCC WARNING:
To assure continued compliance, follow the attached
installation instructions and use only shielded cables
when connecting to other devices. Modifications not
authorized by the manufacturer may void user`s authority
to operate this device.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
EMOVE COVER (OR BACK). NO USER-SERVICEABLE ART
NSIDE EFER SERVICING T UALIFIED ERVICE PERSONNEL.
The lightning flash with arrowhead symbol
within an equilateral triangle is intended to alert
the user to the presence of uninsulated
dangerous voltage within the product`s
enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and
maintenance(servicing) instructions in the
literature accompanying the appliance.
S
I
P
S
O Q. R
R
t d ii
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
This equipment should be installed and operated with minimum
distance 20cm between the radiator and your body.
3
Before using the unit, be sure to read all operating instructions carefully. Please note that these
are general precautions and may not pertain to your unit.
1) Read these instructions.
All the safety and operating instructions should be read before the product is operated.
2) Keep these instructions.
The safety and operating instructions should be retained for future reference.
3) Heed all warnings.
All warnings on the product and in the operating instructions should be adhered to.
4) Follow all instructions.
All operating and use instructions should be followed.
5) Do not use this apparatus near water.
Do not use this product near water and moisture, for example: near a bathtub, washbowl, kitchen
sink or laundry tub; in a wet basement; or near a swimming pool.
6) Clean only with dry cloth.
Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol
cleaners. Use a dry cloth for cleaning.
7) Do not block any ventilation openings. Install in accordance with the manufacturer's
instructions.
Slots and openings in the cabinet and in the back or bottom are provided for ventilation, to ensure
reliable operation of the product and to protect it from overheating. These openings must not be
blocked or covered. The openings should never be blocked by placing the product on a bed, sofa,
rug or other similar surface. This product should never be placed near or over a radiator or heat
source. This product should not be placed in a built-in installation such as a bookcase or rack
unless proper ventilation is provided or the manufacturer's instructions have been adhered to.
8) Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus(including amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug
has two blades with one wider than the other. A grounding type plug has two blades and a
third grounding prong. The wide blade or the third prong are provided for your safety. If the
provided plug does not fit into your outlet, consult an electrician for replacement of the
obsolete outlet .
10)Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
11)Only use attachments/accessories specified by the manufacturer.
12)Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold
with the apparatus. When a cart is used, use caution when moving the cart/apparatus
combination to avoid injury from tip-over.
An appliance and cart combination should be moved with care.
Quick stop, excessive force and uneven surfaces may cause the
appliance and cart combination to overturn.
13) Unplug this apparatus during lightning storms or when unused for long periods of time.
To protect your product from a lightning storm, or when it is left unattended and unused for long
periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This
will prevent damage to the product due to lightning and power-line surges.
14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus
has been damaged in any way, such as power-supply cord or plug is damaged, liquid has
been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain
or moisture does not operate normally, or has been dropped.
15) Power source
This product should be operated only from the type of power source indicated on the marking label.
If you are not sure of the type of power supply to your home, consult your appliance dealer or local
power company. For products intended to operate from battery power, or other source, refer to the
operation instructions.
16) Power lines
An outside antenna system should not be located in the vicinity of overhead power lines or other
electric light or power circuits, or where it can fall into such power lines or circuits. When
installing an outside antenna system, extreme care should be taken to keep from touching such
power lines or circuits as contact with them might be fatal.
For example, this unit may not have the capability to be connected to an outdoor antenna.
Portable Cart Warning
4
17) Overloading
Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock.
18) Object and liquid entry
Never push objects of any kind into the product through openings as they may touch dangerous
voltage points or short out parts that could result in fire or electric shock. Never spill or spray any
type of liquid on the product.
19) Outdoor antenna grounding
If an outside antenna is connected to the product,be sure the antenna system is grounded so as to
Provide some protection against voltage surges and built up static charges.Section 810 of the
National Electric Code ANSI/NFPA 70 provides information with respect to proper to grounding
of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge product,
size of grounding conductors,location of antenna-discharge product,connection to grounding
electrodes and requirements for the grounding electrodes.
Do not attempt to service this product yourself as opening or removing covers may expose you to
dangerous voltage or other hazards.Refer all servicing to qualified service personnel.
When replacement parts are required,be sure the service technician uses replacement parts
specified by the manufacturer or those that have the same characteristics as the original parts.
Unauthorized substitutions may result in fire or electric shock or other hazards.
Upon completion of any service or repairs to this product,ask the service technician to perform
safety checks to determine that the product is in proper operational condition.
The product should be mounted to a wall or ceiling only as recommended by the manufacturer.
Unplug this product from the wall outlet and refer service to qualified service personnel under the
following conditions.
a)When the power-supply cord or plug is damaged.
b)If liquid has been spilled or objects have fallen into the product.
c)If the product has been exposed to rain or water.
d)If the product does not operate normally by following the operating instructions.Adjust only
those controls that are covered by the operating instructions,as an adjustment of other
controls may result in damage and will and require extensive work by a qualified technician
to restore in the product to its normal operation.
e)If the product has been dropped or the cabinet has been damaged.
f)When the product exhibits a distinct change in performance-this indicates a need for service.
This reminder is provided to call the CATV system installer's attention to Article 820-40 of the
NEC that provides guidelines for proper grounding and,in particular,specifies that the cable
ground shall be connected to the grounding system of the building,as close to the point of cable
entry as practical.
NOTE: Refer all servicing to qualified service personnel. Servicing is required when
the unit has been damaged in any way such as the following: the power-supply cord
or plug has been damaged, liquid has been spilled into unit, the unit has been
exposed to rain or moisture, the unit has been dropped or the unit does not operate normally.
25) Note to CATV system installer
24) Damage requiring service
23) Wall or ceiling mounting
22) Safety check
21) Replacement parts
20) Service
1
TOP PANEL
FRONT VIEW REAR PANEL
5
TUNE- / VOL-
STANDBY/
SOURCE
AUX IN
TUNE+/ VOL+
23
4
5
6
78
9
9
10
11
12
1. AUX IN Jack
2. /TUNE-/VOL- (Skip
4. STANDBY/SOURCE Button
5. (Play/Pause) Button
6. RESET Button
7. Remote Sensor
8. Indicator
9. Speakers
10. FM ANT (FM wire antenna)
11. LINE IN Jacks
12. DC IN Jack
RESET
LINE IN
L
R
FM ANT
DC I N
DC 9V, 1.3A
LOCATION OF CONTROLS
backward/Tuning down/
Volume down) Button
3. /TUNE+/VOL+ (Skip
forward/Tuning up/
Volume up) Button
1. /STANDBY Button
3. VOL- (Volume Down) Button
4. SOURCE Button
7. (Mute) Button
6. (Play/Pause) Button
8. VOL+ (Volume Up) Button
REMOTE CONTROL
6
RESET
TUN E TUN E+-
BATTERY INSTALLATION (REMOTE CONTROL)
1
2
3
4
5
6
7
8
9
2. RESET Button
Remove and discard the insulation film as illustrated on the right.
RELEASE
PUSH
OPEN
R2025
C
+
SN
Fig.1 Fig.2 Fig.3
First Time Use:
If the button cell is drained, replace it by a new one as below:
1. Push and slide out the button cell holder as Fig.1 below.
2. Replace the button cell with a new CR2025 button cell as the polarity
markings on the rear of the Remote Control as Fig.2 below.
3. Close the button cell holder as Fig.3 below.
5. /TUNE- (Skip backward/
Tuning down Button
9. /TUNE+ (Skip forward/
Tuning up Button
7
°
30 °
30
Approx. 16 feet
When there is an obstacle between the unit and the transmitter, the unit may not operate.
Follow these Battery Precaution when using a battery in this device:
1. Use only the size and type of battery specified.
6. Do not dispose of battery in fire. Battery may explodes or leak.
7. Clean the battery contacts and also those of the device prior to battery installation.
BATTERY PRECAUTIONS:
2. Be sure to follow the correct polarity when installing the battery as indicated in the battery
compartment. A reversed battery may cause damage to the device.
3. Do not mix different types of batteries together (e.g. Alkaline and Carbon-zinc) or old batteries
with fresh ones.
4. If the batteries in the device are consumed or the device is not to be used for a long period of
time, remove the batteries to prevent damage or injury from possible battery leakage.
5. Do not try to recharge the battery not intended to be recharged; it can overheat and rupture.
(Follow battery manufacturer’s instructions.)
8. This product contains a coin/button cell battery. If the coin/button cell battery is
swallowed, it can cause severe internal burn in just 2 hours and can lead to death.
Keep new and used batteries away from children. If the battery compartment does not close
securely, stop using the product and keep it away from children.
If you think batteries might have been swallowed or placed inside any part of the body, seek
immediate medical attention.
NOTES:
When direct sunlight, an incandescent lamp, fluorescent lamp or any other strong light shines
on the REMOTE SENSOR of the unit, the operation of the remote may be unstable.
EFFECTIVE DISTANCE OF REMOTE TRANSMITTER
POWER SOURCE
8
Connect the small plug from supplied AC/DC Adaptor to the DC IN Jack on the rear of unit then plug the
AC/DC Adaptor to a wall outlet having AC 100-240V~; 50/60Hz.
To AC outlet
AC/DC Adapter
To the DC IN jack
on the rear of the unit
LINE IN
L
R
FM ANT
DC I N
DC 9V, 1.3A
NOTES:
If you will not use the unit for an extended period of time, unplug the AC/DC Adaptor from wall outlet.
The AC/DC Adaptor is intended to be correctly orientated in a vertical or floor mount position.
The Red Standby Indicator on the top
of unit will illuminate.
OPERATION
9
GENERAL OPERATION:
1. Connect the supplied AC/DC Adaptor to the unit and wall outlet as previously instructed. The Red
Standby Indicator on the top of unit will illuminate.
2. Press and hold the STANDBY/SOURCE Button on the top of unit or press the Button
on the
Remote Control to turn on the unit from standby mode. The color of the indicator will turn to
correspondent color. You will also hear an audible say “Power on”.
3. Press the STANDBY/SOURCE Button on the top of unit or press the SOURCE Button on the
Remote Control repeatedly to switch to desired playback mode. The color of the indicator will turn
to correspondent with your selection (see list below):
Playback Mode: Color of Indicators:
BT (Bluetooth) Blue (and blinking)
FM Radio Green
LINE IN Purple (Red + Blue)
AUX IN Orange (Red + Green)
4. During playback,
Press the /Tune -/VOL – or /Tune +/VOL + buttons on the unit or the VOL +/- buttons
on the Remote Control to adjust volume level as desired.
Press the (MUTE) Button on the Remote Control to turn off the sound temporary, press
again to turn it back.
Press and hold the SOURCE/LED 1 Button on the top of unit to power On/Off all the
Decorative LED Lights.
5. When finished, press and hold STANDBY/SOURCE Button on the top of unit or press the
Button the Remote Control to turn the unit to standby mode. The color of the Indicator
will turn to Red.
6. If you will not use the unit for an extended period of time, unplug the AC/DC Adaptor from wall outlet.
STANDBY
/
STANDBY
/
10
BT (Bluetooth):
Listen music from external BT device:
BT (Bluetooth) pairing:
First time use or re-pairing the unit to a new BT Device, pair as follows:
1. Power on the unit as previously instructed.
2. Press the STANDBY/SOURCE Button on the top of unit or press the SOURCE Button on the
Remote Control repeatedly until the color of the indicator turn to Blue and blink.
3. Power on the external BT Device and enter to BT searching mode. Start pairing following the on
screen instructions from the external BT Device. After paired, the Blue Indicator will stop blinking.
4. If pairing is complete you may now play music with your external BT Device.
5. During playback:
Press the Button on the unit or Remote Control to pause, press again to resume normal
playback.
Press the (MUTE) Button on the Remote Control to turn off the sound temporary, press
again to turn it back.
Press the buttons on the unit or the VOL +/- buttons
on the Remote Control to adjust volume level as desired.
Press and hold the buttons on the unit or press the
/Tune - or /Tune + buttons on the Remote Control to skip tracks.
Notes:
When the external BT Device searched the unit, our model number “MHT843n” will appear on
the
display of external BT Device.
If while pairing you are asked for a code please try "0000" or "1234".
Normal operation after pairing:
1. Power on the external BT Device and enter to BT playback mode.
2. Power on the unit and enter to BT mode as previously instructed. The color of the indicator will turn
to Blue and blink.
3. Wait a few seconds until the unit is automatically paired to the external BT Device. (The Blue
Indicator will stop blinking).
4. After pairing is complete you may now play music with your external BT Device.
/Tune -/VOL – or /Tune +/VOL +
/Tune -/VOL – or /Tune +/VOL +
11
FM Radio:
1. Power on the unit as previously instructed.
2. Press the STANDBY/SOURCE Button on the top of unit or press the SOURCE Button on the
Remote
Control repeatedly until the color of the indicator turn to Green.
3. Press and hold the /Tune -/VOL – or /Tune +/VOL + buttons on the unit or press the
/Tune - or /Tune + buttons on the Remote Control to search and play the next/previous
available FM station.
4. Repeat the same procedures until the desired station was search and play.
5. If you want researching the stations from beginning (87.5MHz), press the RESET Button on the
unit or Remote Control then search the Radio station as point 3 above again.
Antennas:
This unit has a FM wire antenna on the rear of unit, which provides adequate reception in most areas.
If reception is weak, unwound and extended to its full length or reassemble the other direction/location
to improve reception.
12
AUX IN:
Listen music from external Audio Player such like MP3 Player; Discman … etc:
1. Connect one side of supplied Audio Connection Cable to the Phones Jack; Line Out Jack or AUX
Out Jack on the external Audio Player.
2. Connect the other side of the cable to the AUX IN Jack on the top of unit as illustrate below:
3. Power on the unit as the instructed earlier.
4. Press the STANDBY/SOURCE Button on the top of unit or press the SOURCE Button on the
Remote Control repeatedly until the color of the indicator turn to Orange (Red + Green).
5. Plays the music on the connected external Audio Player as usual. (Make sure the volume level
of the external Audio Player is in high level. Otherwise, sound from this unit may weak).
Mobile Phone
Connect to the Phones; AUX Out;
Line Out Jack of the external devices
(Such like MP3 Player; cell phones;
iPod/iPad ... etc)
MP3 Player
TU NE- / VO L-
STANDB Y/
SO URCE
AUX IN
TU NE+/ V OL+
RESET
13
LINE IN:
Listen music from external Video/Audio Player DVD Player/TV …. etc:
1. Connect one side of RCA Connection Cable (not included) to the RCA audio Jacks on the
external Video/Audio Player.
2. Connect the other side of the cable to the LINE IN Jacks on the rear of unit as illustrate below:
3. Power on the unit as the instructed earlier.
4. Press the STANDBY/SOURCE Button on the top of unit or press the SOURCE Button on the
Remote Control repeatedly until the color of the indicator turn to Purple (Red + Blue).
5. Plays the video/music on the connected external Video/Audio Player as usual. (Make sure the
volume level of the external Video/Audio Player is in high level. Otherwise, sound from this unit
may weak).
Line out jacks of
TV/DVD player etc.
L
R
Video
LINE IN
L
R
FM ANT
DC I N
DC 9V, 1.3A
white
red
TROUBLESHOOTING GUIDE
If you are having problems with your unit, please review the guide below before requesting.
SYSTEM POSSIBLE CAUSE POSSIBLE SOLUTION
14
The unit had not connect to AC power Connect the supplied AC/DC Adaptor to
the unit and wall outlet
Press and hold the STANDBY/SOURCE
Button on the top of unit or press the
/STANDBY Button on the Remote
Control to turn on the unit
No power
The unit is in standby mode
Volume is set to minimum Press the /Tune +/VOL + button
on the unit or the VOL + button on
the Remote Control
Volume level of paired/connected
device is in low level
No sound
Rise the volume level of the
paired/connected device
Volume level is too high
Press the /Tune -/VOL - button
on the unit or the VOL - button on
the Remote Control
Reduce the volume level of the
paired/connected device
Sound
distortion
Radio weak
reception
Volume level of paired/connected
device is too high
Unwound and extended the wire antenna
to its full length or reassemble the other
direction/location to improve reception
Remote
not functioning The button cell in remote control
is drained Replace with new button cell
Bluetooth
fail to pair
The external BT device is too far
from the unit Place the external BT device
close to the unit
The external BT device had
NOT paired to the unit Pair the external BT device to
the unit as page 10 indicates
GENERAL SPECIFICATIONS
PACKAGE INCLUDES:
Power source................................................................................DC 9V 1300mA
Speaker...................................................................................................8W x 4ohm per channel
1 x Owner's Manual
1 x AC/DC Adapter
15
Audio Power..........................................................................5W per channel (Total 10 W, RMS)
FM radio frequency...............................................................................................87.5-108.0MHz
Bluetooth version....................................................................................................................V4.2
Bluetooth working range............................................................................ 32 feet in open area
≤
1 x Audio Connection Cable with 3.5mm plugs
1 x Remote Control (Uses 1 x CR2025 Button Cell, included)
(Input: 100-240V~ 50/60Hz 0.5A
Output: 9V 1300mA)
