Jvc Ks Lh60R Users Manual LH60R[E_EX]

kslh60r 53d858c7-38ac-4442-91e6-68a8f81a5a2e JVC Cassette Player KS-LH60R User Guide |

: Jvc Jvc-Ks-Lh60R-Users-Manual-320862 jvc-ks-lh60r-users-manual-320862 jvc pdf

Open the PDF directly: View PDF .
Page Count: 48

GET0127-001A

[E/EX]

KS-LH60R

CASSETTE RECEIVER

CASSETTEN-RECEIVER

RADIOCASSETTE

RADIO/CASSETTESPELER

ENGLISH

DEUTSCH

NEDERLANDS

FRANÇAIS

For installation and connections, refer to the separate manual.

Für den Einbau und die Anschlüsse siehe das eigenständige Handbuch.

Pour l’installation et les raccordements, se référer au manuel séparé.

Bijzonderheden over de installatie en aansluiting van het apparaat vindt u in de

desbetreffende handleiding.

INSTRUCTIONS

BEDIENUNGSANLEITUNG

MANUEL D’INSTRUCTIONS

GEBRUIKSAANWIJZING

SOUND

VOL VOL

SOURCE

RF

U

D

ATT

Cover001AKS-LH60R[E_EX]f.p65 3/7/03, 7:08 PM3

2

ENGLISH

How to reset your unit

After detaching the control panel, press the reset button on the panel holder using a ball-point pen

or a similar tool.

This will reset the built-in microcomputer.

Note:

Your preset adjustments—such as preset channels or sound adjustments—will also be erased.

How to use the M (MODE) button

If you press M (MODE), the unit goes into functions mode (“MODE” flashes on the upper part of the

display). While in functions mode, the number buttons work as different function buttons.

• When connecting a JVC MP3-compatible CD changer: The 5/∞ buttons will also work as

+10/–10 buttons after pressing M (MODE).

Ex.: When number button 2 works as MO (monaural) button.

To use these buttons for original functions again after pressing M (MODE), wait for 5 seconds

without pressing any of these buttons until the functions mode is cleared (“MODE” disappears from

the display).

• Pressing M (MODE) again also clears the functions mode.

Time countdown

indicator

MO (monaural)

indicator lights up.

EN02-04KS-LH60R[E_EX]f.p65 3/7/03, 7:08 PM2

3

ENGLISH

CONTENTS

Thank you for purchasing a JVC product. Please read all instructions carefully before operation,

to ensure your complete understanding and to obtain the best possible performance from the unit.

BEFORE USE

*

For safety....

• Do not raise the volume level too much, as this will

block outside sounds, making driving dangerous.

• Stop the car before performing any complicated

operations.

*

Temperature inside the car....

If you have parked the car for a long time in hot or

cold weather, wait until the temperature in the car

becomes normal before operating the unit.

How to reset your unit ............................... 2

How to use the M (MODE) button ............. 2

LOCATION OF THE BUTTONS ............ 4

Control panel ............................................. 4

Remote controller ...................................... 5

Preparing the remote controller ................ 6

BASIC OPERATIONS ....................... 7

Turning on the power ................................ 7

Setting the clock ........................................ 8

RADIO OPERATIONS ...................... 9

Listening to the radio ................................. 9

Storing stations in memory ....................... 10

Tuning in to a preset station ...................... 11

RDS OPERATIONS ......................... 12

What you can do with RDS ....................... 12

Other convenient RDS functions and

adjustments ............................................ 16

TAPE OPERATIONS ........................ 19

Listening to a cassette .............................. 19

Finding the beginning of a tune ................. 20

Other convenient tape functions ............... 21

Prohibiting cassette ejection ..................... 22

SOUND ADJUSTMENTS ................... 23

Selecting preset sound modes

(C-EQ: custom equalizer) ....................... 23

Adjusting the sound .................................. 24

OTHER MAIN FUNCTIONS ................ 25

Changing the general settings (PSM) ....... 25

Detaching the control panel ...................... 29

CD CHANGER OPERATIONS .............. 30

About MP3 discs ....................................... 30

Playing discs ............................................. 30

Selecting the playback modes .................. 34

EXTERNAL COMPONENT OPERATIONS ... 35

Playing an external component ................. 35

DAB TUNER OPERATIONS ................ 36

Tuning in to an ensemble and one of the

services .................................................. 36

Storing DAB services in memory .............. 37

Tuning in to a preset DAB service ............. 38

What you can do more with DAB .............. 39

TROUBLESHOOTING ...................... 40

MAINTENANCE ............................. 42

SPECIFICATIONS ........................... 43

Note:

For security reasons, a numbered ID card is provided with this unit, and the same ID number is imprinted on

the unit’s chassis. Keep the card in a safe place, as it will help the authorities to identify your unit if stolen.

EN02-04KS-LH60R[E_EX]f.p65 3/7/03, 7:08 PM3

4

ENGLISH

LOCATION OF THE BUTTONS

Control panel

1(standby/on/attenuator) button

2SEL (select) button

3Control dial

4Display window

54 /¢ buttons

65 (up) button

23 (tape direction) button

70 (eject) button

8∞ (down) button

9Remote sensor

p (control panel release) button

qT (TP/PTY: traffic programme/programme

type) button

wD (DISP: display) button

• Also functions as SSM buttons when pressed

together with M (MODE) button.

eM (MODE) button

• Also functions as SSM buttons when pressed

together with D (DISP) button.

rFM/AM (DAB) button

tTAPE (CD-CH: CD changer) button

yEQ (equalizer) button

uMO (monaural) button

i (Dolby B) button

oNumber buttons

;RPT (repeat) button

aRND (random) button

• Functions only when connecting to a CD changer.

Display window

sDisc information indicators

TAG (ID3 Tag), (folder), (track/file)

• Lights up only when playing an MP3 disc or a

CD Text on a JVC MP3-compatible CD changer.

dTape-in indicator

fMain display

gPlayback item indicators

(disc)

• Lights up only when connecting to a CD changer.

(folder)

• Lights up only when playing an MP3 disc on a

JVC MP3-compatible CD changer.

hSource/clock display

jRND (random) indicator

• Lights up only when connecting to a CD changer.

kEQ (equalizer) indicator

lSound mode (C-EQ: custom equalizer)

indicators

ROCK, CLASSIC, POPS, HIP HOP, JAZZ,

USER

/ (Dolby B) indicator

zTuner reception indicators

MO (monaural), ST (stereo)

xLOUD (loudness) indicator

cRDS indicator

AF, REG, TP, PTY

vMP3 indicator

• Lights up only when playing an MP3 disc on a

JVC MP3-compatible CD changer.

bVolume (or audio) level indicator

Equalizer pattern indicator

nRPT (repeat) indicator

41 2 3

or t

6 8

7

ew

q

p u i ; a

9

5

y

k l zvb

f g h

s d j

xn/c

Display window

EN02-04KS-LH60R[E_EX]f.p65 3/24/03, 12:20 PM4

ENGLISH

5

Remote controller

SOUND

VOL VOL

SOURCE

RF

U

D

ATT

3• Selects the preset stations while listening to

the radio (or the DAB tuner).

Each time you press the button, the preset

station (or service) number increases, and

the selected station (or service) is tuned in.

• While playing an MP3 disc on an MP3-

compatible CD changer;

– Skips to the previous disc if pressed

briefly.

– Skips to the previous folder if pressed and

held.

Note:

While playing a CD on a CD changer, this

always skips to the previous disc.

4Functions the same as the control dial on the

main unit.

Note:

These buttons do not function for the

preferred setting mode adjustment.

5Selects the sound mode (C-EQ: custom

equalizer).

Each time you press the button, the sound

mode (C-EQ) changes.

6Selects the source.

Each time you press the button, the source

changes.

7• Searches for stations while listening to the

radio.

• Selects services while listening to the DAB

tuner if pressed briefly.

• Searches for ensembles while listening to

the DAB tuner if pressed for more than one

second.

• Functions as the fast-forward or rewind

buttons if pressed and held while listening to

a cassette.

To release this operation, press button 2 to

resume playback.

• Functions as Multi Music Scan buttons if

pressed while listening to a cassette.

To release this operation, press button 2 to

resume playback.

• Fast-forwards or reverses the track/file if

pressed and held while listening to the CD

changer.

• Skips to the beginning of the next track/file

or goes back to the beginning of the current

(or previous) tracks/files if pressed briefly

while listening to the CD changer.

1• Turns on the unit if pressed when the unit is

turned off.

• Turns off the unit if pressed and held until

“SEE YOU” appears on the display.

• Drops the volume level in a moment if

pressed briefly.

Press again to resume the volume.

2• Selects the band while listening to the radio

(or the DAB tuner).

Each time you press the button, the band

changes.

• Changes the tape direction while listening to

a cassette.

Each time you press the button, the tape

direction changes alternately.

• While playing an MP3 disc on an MP3-

compatible CD changer;

– Skips to the next disc if pressed briefly.

– Skips to the next folder if pressed and

held.

Note:

While playing a CD on a CD changer, this

always skips to the next disc.

EN05-06KS-LH60R[E_EX]f.p65 3/7/03, 7:08 PM5

ENGLISH

6

Preparing the remote

controller

Before using the remote controller:

• Aim the remote controller directly at the remote

sensor on the main unit. Make sure there is no

obstacle in between.

• Do not expose the remote sensor to strong

light (direct sunlight or artificial lighting).

Installing the battery

When the controllable range or effectiveness of

the remote controller decreases, replace the

battery.

1. Remove the battery holder.

1) Push out the battery holder in the direction

indicated by the arrow using a ball-point

pen or a similar tool.

2) Remove the battery holder.

2. Place the battery.

Slide the battery into the holder with the +

side facing upwards so that the battery is

fixed in the holder.

Lithium coin

battery (product

number: CR2025)

Remote sensor

(back side)

3. Return the battery holder.

Insert again the battery holder by pushing it

until you hear a clicking sound.

WARNING:

• Store the battery in a place where children

cannot reach.

If a child accidentally swallows the battery,

consult a doctor immediately.

• Do not recharge, short, disassemble, or heat the

battery or dispose of it in a fire.

Doing any of these things may cause the battery

to give off heat, crack, or start a fire.

• Do not leave the battery with other metallic

materials.

Doing this may cause the battery to give off

heat, crack, or start a fire.

• When throwing away or saving the battery,

wrap it in tape and insulate; otherwise, the

battery may start to give off heat, crack, or start

a fire.

• Do not poke the battery with tweezers or similar

tools.

Doing this may cause the battery to give off

heat, crack, or start a fire.

CAUTION:

DO NOT leave the remote controller in a place

(such as dashboards) exposed to direct sunlight

for a long time. Otherwise, it may be damaged.

KS-LH60R is equipped with the steering

wheel remote control function.

If your car is equipped with the steering wheel

remote controller, you can operate this

receiver using the controller.

• See the Installation/Connection Manual

(separate volume) for connection to utilize

this function.

(back side)

EN05-06KS-LH60R[E_EX]f.p65 3/7/03, 7:08 PM6

7

ENGLISH

Turning on the power

1

Turn on the power.

Note on One-Touch Operation:

When you select a source in step

2

below, the

power automatically comes on. You do not have

to press this button to turn on the power.

2

Select the source.

To operate the tuner (FM or AM),

see pages 9 – 18.

To play a tape,

see pages 19 – 22.

To operate the CD changer,

see pages 30 – 34.

To operate the external component

(LINE IN), see page 35.

To operate the DAB tuner,

see pages 36 – 39.

BASIC OPERATIONS

3

Adjust the volume.

4

Adjust the sound as you want. (See

pages 23 and 24.)

To drop the volume in a moment

Press briefly while listening to any

source. “AT T ” starts flashing on the display, and

the volume level will drop in a moment.

To resume the previous volume level, press the

button briefly again.

•If you turn the control dial, you can also restore

the sound.

To turn off the power

Press and hold for more than one

second.

“SEE YOU” appears, then the unit turns off.

Volume (or audio) level indicator

(see page 27)

Volume level appears.

To increase the volume

To decrease the volume

3

12

EN07-08KS-LH60R[E_EX]f.p65 3/7/03, 7:09 PM7

8

ENGLISH

Setting the clock

You can also set the clock system to either

24 hours or 12 hours.

1

Press and hold SEL (select) for more

than 2 seconds so that one of the

PSM items appears on the display.

(PSM: see page 26.)

2

Set the hour.

1Select “CLOCK H” (hour) if not shown on

the display.

2Adjust the hour.

12

3

Set the minute.

1Select “CLOCK M” (minute).

2Adjust the minute.

12

4

Set the clock system.

1Select “24H/12H.”

2Select “24H” or “12H.”

12

5

Finish the setting.

Note:

To show the clock time on the display, see page 27.

To check other information during play, press

D (DISP).

Each time you press the button, the other

information will be shown on the upper part of

the display. (See page 27 for details.)

•Pressing D (DISP) with the unit turned off will

show the clock time for about 5 seconds.

EN07-08KS-LH60R[E_EX]f.p65 3/7/03, 7:09 PM8

9

ENGLISH

RADIO OPERATIONS

To stop searching before a station is received,

press the same button you have pressed for

searching.

Searching a station manually:

Manual search

1

Select the band (FM1 – 3, AM).

Each time you press the

button, the band changes as

follows:

Note:

This receiver has three FM bands (FM1, FM2,

FM3). You can use any one of them to listen to an

FM broadcast.

2

Press and hold ¢ or 4

until “MANU” (manual) starts

flashing on the display.

CONTINUED ON THE NEXT PAGE

FM 1

(F1)

FM 2

(F2)

FM 3

(F3)

A M

Listening to the radio

You can use either automatic searching or manual

searching to tune in to a particular station.

Searching a station automatically:

Auto search

1

Select the band (FM1 – 3, AM).

Each time you press the

button, the band changes as

follows:

*When “CLOCK” is set to “ON” (see page 27),

the current indication will soon change to the

clock time.

Note:

This receiver has three FM bands (FM1, FM2,

FM3). You can use any one of them to listen to

an FM broadcast.

2

Start searching a station.

When a station is received, searching stops.

Selected band appears*.

Lights up when receiving an FM stereo

broadcast with sufficient signal strength.

To search stations of

higher frequencies

To search stations of

lower frequencies

FM 1

(F1)

FM 2

(F2)

FM 3

(F3)

A M

EN09-11KS-LH60R[E_EX]f.p65 3/7/03, 7:09 PM9

10

ENGLISH

Storing stations in memory

You can use one of the following two methods to

store broadcasting stations in memory.

• Automatic preset of FM stations: SSM (Strong-

station Sequential Memory)

• Manual preset of both FM and AM stations

FM station automatic preset: SSM

You can preset 6 local FM stations in each FM

band (FM1, FM2, and FM3).

1

Select the FM band (FM1 – 3) you

want to store FM stations into.

Each time you press the

button, the band changes as

follows:

2

Press and hold both buttons for

more than 2 seconds.

Local FM stations with the strongest signals are

searched and stored automatically in the band

number you have selected (FM1, FM2, or FM3).

These stations are preset in the number buttons

—No.1 (lowest frequency) to No.6 (highest

frequency).

When automatic preset is over, the station stored

in number button 1 will be automatically tuned in.

“- -SSM- -” appears, then disappears

when automatic preset is over.

3

Tune in to a station you want while

“MANU” (manual) is flashing.

• If you release your finger from the button,

the manual mode automatically turns off

after 5 seconds.

• If you hold down the button, the frequency

keeps changing (in 50 kHz intervals for

FM and 9 kHz for AM—MW/LW) until you

release the button.

When an FM stereo broadcast is hard to

receive:

1Press M (MODE) to enter the

functions mode while listening

to an FM stereo broadcast.

“MODE” flashes on the upper

part of the display.

2Press MO (monaural), while

“MODE” is still flashing on the

display, so that the MO

indicator lights up on the

display.

Each time you press the

button, the MO indicator lights

up and goes off alternately.

When the MO indicator is lit on the display, the

sound you hear becomes monaural but the

reception will be improved.

MO (monaural) indicator

To search stations of

higher frequencies

To search stations of

lower frequencies

FM 1

(F1)

FM 2

(F2)

FM 3

(F3)

A M

EN09-11KS-LH60R[E_EX]f.p65 3/7/03, 7:09 PM10

11

ENGLISH

Manual preset

You can preset up to 6 stations in each band

(FM1, FM2, FM3, and AM) manually.

Ex.: Storing FM station of 92.5 MHz into the

preset number 1 of the FM1 band.

1

Select the band (FM1 – 3, AM) you

want to store stations into (in this

example, FM1).

Each time you press the

button, the band changes as

follows:

2

Tune in to a station (in this example,

of 92.5 MHz).

3

Press and hold the number button

(in this example, 1) for more than

2 seconds.

4

Repeat the above procedure to store

other stations into other preset

numbers.

Notes:

• A previously preset station is erased when a new

station is stored in the same preset number.

• Preset stations are erased when the power supply to

the memory circuit is interrupted (for example,

during battery replacement). If this occurs, preset

the stations again.

Tuning in to a preset station

You can easily tune in to a preset station.

Remember that you must store stations first. If

you have not stored them yet, see “Storing

stations in memory” on pages 10 and 11.

1

Select the band (FM1 – 3, AM).

Each time you press the

button, the band changes as

follows:

2

Select the number (1 – 6) for the

preset station you want.

Selected band/preset number

and “MEMO” (memory) appear

alternately for a while.

FM 1

(F1)

FM 2

(F2)

FM 3

(F3)

A M

To search stations of

higher frequencies

To search stations of

lower frequencies

FM 1

(F1)

FM 2

(F2)

FM 3

(F3)

A M

EN09-11KS-LH60R[E_EX]f.p65 3/7/03, 7:09 PM11

12

ENGLISH

RDS OPERATIONS

What you can do with RDS

RDS (Radio Data System) allows FM stations to

send an additional signal along with their regular

programme signals. For example, the stations

send their station names, as well as information

about what type of programme they broadcast,

such as sports or music, etc.

Another advantage of RDS function is called

“Enhanced Other Networks.” By using the

Enhanced Other Networks data sent from a

station, you can tune in to a different station of a

different network broadcasting your favorite

programme or traffic announcement while

listening to another programme or to another

source such as tape.

By receiving the RDS data, this unit can do the

following:

• Tracing the same programme automatically

(Network-Tracking Reception)

• Standby Reception of TA (Traffic

Announcement) or your favorite programme

• PTY (Programme Type) search

• Programme search

• And some other functions

Tracing the same programme

automatically (Network-Tracking

Reception)

When driving in an area where FM reception is

not good, the tuner built in this unit automatically

tunes in to another RDS station, broadcasting the

same programme with stronger signals. So, you

can continue to listen to the same programme in

its finest reception, no matter where you drive.

(See the illustration on page 18.)

Two types of the RDS data are used to make

Network-Tracking Reception work correctly

—PI (Programme Identification) and AF

(Alternative Frequency).

Without receiving these data correctly from the

RDS station you are listening to, Network-

Tracking Reception will not operate.

To use Network-Tracking Reception

You can select the different modes of network-

tracking reception to continue listening to the

same programme in its finest reception.

When shipped from the factory, “AF” is selected.

• AF: Network-Tracking Reception is

activated with Regionalization set to

“off.”

With this setting, the unit switches to

another station within the same

network when the receiving signals

from the current station become

weak. (In this mode, the programme

may differ from the one currently

received.)

The AF indicator lights up but the

REG indicator does not.

• AF REG: Network-Tracking Reception is

activated with Regionalization set to

“on.”

With this setting, the unit switches to

another station, within the same

network, broadcasting the same

programme when the receiving

signals from the current station

become weak.

Both the AF indicator and the REG

indicator light up.

• OFF: Network-Tracking Reception is

deactivated.

Neither the AF indicator nor the REG

indicator lights up.

Note:

If a DAB tuner is connected and Alternative Reception

(for DAB services) is activated, Network-Tracking

Reception (“AF”) is also activated automatically. On

the other hand, Network-Tracking Reception cannot

be deactivated without deactivating Alternative

Reception. (See page 39.)

AF indicator REG indicator

EN12-18KS-LH60R[E_EX]f.p65 3/7/03, 7:09 PM12

13

ENGLISH

1

Press and hold SEL (select) for more

than 2 seconds so that one of the

PSM items appears on the display.

(PSM: see page 26.)

2

Select “AF-REG” (alternative

frequency/regionalization reception)

if not shown on the display.

3

Select the desired mode—“AF,”

“AF REG,” or “OFF.”

4

Finish the setting.

Using TA Standby Reception

TA Standby Reception allows the unit to switch

temporarily to Traffic Announcement (TA) from

the current source (another FM station, tape, or

other connected components).

• TA Standby Reception will not work if you are

listening to an AM station.

Press T (TP/PTY) to activate TA Standby

Reception.

7When the current source is FM, the TP

indicator either lights up or flashes.

•If the TP indicator lights up, TA Standby

Reception is activated.

If a station starts broadcasting a traffic

announcement, “TRAFFIC” appears on the

display, and this unit automatically tunes in to

the station. The volume changes to the

preset TA volume level (see page 17) and the

traffic announcement can be heard.

•If the TP indicator flashes, TA Standby

Reception is not yet activated since the

station being received does not provide the

signals used for TA Standby Reception.

To activate TA Standby Reception, you need

to tune in to another station providing these

signals. Press ¢ or 4 to search

for such a station.

When a station providing these signals is

tuned in, the TP indicator stops flashing and

remains lit. Now TA Standby Reception is

activated.

7When the current source is other than FM,

the TP indicator lights up.

If a station starts broadcasting a traffic

announcement, “TRAFFIC” appears on the

display, and this unit automatically changes the

source and tunes in to the station.

To deactivate the TA Standby Reception,

press T (TP/PTY) again. The TP indicator goes

off.

EN12-18KS-LH60R[E_EX]f.p65 3/7/03, 7:09 PM13

14

ENGLISH

4

Finish the setting.

7When the current source is FM, the PTY

indicator either lights up or flashes.

•If the PTY indicator lights up, PTY Standby

Reception is activated.

If a station starts broadcasting the selected

PTY programme, this unit automatically

tunes in to the station.

•If the PTY indicator flashes, PTY Standby

Reception is not yet activated since the

station being received does not provide the

signals used for PTY Standby Reception.

To activate PTY Standby Reception, you

need to tune in to another station providing

these signals. Press ¢ or 4 to

search for such a station.

When a station providing these signals is

tuned in, the PTY indicator stops flashing

and remains lit. Now PTY Standby Reception

is activated.

7When the current source is other than FM,

the PTY indicator lights up.

If a station starts broadcasting the selected

PTY programme, this unit automatically

changes the source and tunes in to the station.

To deactivate the PTY Standby Reception,

select “OFF” in step

3

on the left column. The

PTY indicator goes off.

Using PTY Standby Reception

PTY Standby Reception allows the unit to switch

temporarily to your favorite programme (PTY:

Programme Type) from the current source

(another FM station, tape, or other connected

components).

• PTY Standby Reception will not work if you are

listening to an AM station.

You can select your favorite programme type for

PTY Standby Reception.

When shipped from the factory, PTY Standby

Reception is turned off. (“OFF” is selected for

PTY Standby Reception.)

1

Press and hold SEL (select) for more

than 2 seconds so that one of the

PSM items appears on the display.

(PSM: see page 26.)

2

Select “PTY STBY” (standby) if not

shown on the display.

3

Select one of the twenty-nine PTY

codes. (See page 18.)

Selected code name

appears on the display

and is stored into

memory.

EN12-18KS-LH60R[E_EX]f.p65 3/7/03, 7:09 PM14

15

ENGLISH

Searching your favorite programme

You can search any one of the PTY codes.

In addition, you can store your 6 favorite

programme types in the number buttons.

When shipped from the factory, the following

6 programme types have been stored in the

number buttons (1 to 6).

To store your favorite programme types, see

below.

To search your favorite programme type, see

page 16.

To store your favorite programme types

1

Press and hold T (TP/PTY) for more

than 2 seconds while listening to an

FM station.

2

Select one of the twenty-nine PTY

codes. (See page 18.)

Selected code name

appears on the display.

3

Press and hold the number button

for more than 2 seconds to store the

PTY code selected into the preset

number you want.

Selected preset number and “MEMO”

(memory) appear alternately.

4

Press and hold T (TP/PTY) for more

than 2 seconds to exit from this

mode.

The last selected PTY code appears.

POP M

123

ROCK M EASY M

456

CLASSICS AFFAIRS VARIED

EN12-18KS-LH60R[E_EX]f.p65 3/7/03, 7:09 PM15

16

ENGLISH

•If there is a station broadcasting a programme

of the same PTY code as you selected, that

station is tuned in.

•If there is no station broadcasting a

programme of the same PTY code as you

selected, the station will not change.

Note:

In some areas, the PTY search will not work correctly.

Other convenient RDS

functions and adjustments

Automatic selection of the station

when using the number buttons

Usually when you press the number button, the

preset station is tuned in.

However, when the preset station is an RDS

station, something different will happen. If the

signals from that preset station are not sufficient

for good reception, this unit, using the AF data,

tunes in to another frequency broadcasting the

same programme as the original preset station is

broadcasting. (Programme search)

•The unit takes some time to tune in to another

station using programme search.

To activate programme search, follow the

procedure below.

•See also “Changing the general settings

(PSM)” on page 25.

1Press and hold SEL (select) for more than

2 seconds so that one of the PSM items

appears on the display.

2Press ¢ or 4 to select

“P(Programme)-SEARCH.”

3Turn the control dial clockwise to select “ON.”

Now programme search is activated.

4Press SEL (select) to finish the setting.

To cancel programme search, repeat the same

procedure and select “OFF” in step 3 by turning

the control dial counterclockwise.

To search your favorite programme type

1

Press and hold T (TP/PTY) for more

than 2 seconds while listening to an

FM station.

2

To select one of your favorite

programme type

or

To select any one of the twenty-nine

PTY codes

3

Press ¢ or 4 to start PTY

search for your favorite programme.

Ex.: When “ROCK M” is selected

The last selected PTY code appears.

Preset number appears only if you select

a PTY code using the number buttons.

EN12-18KS-LH60R[E_EX]f.p65 3/7/03, 7:09 PM16

17

ENGLISH

Setting the TA volume level

You can preset the volume level for TA Standby

Reception. When a traffic programme is received,

the volume level automatically changes to the

preset level.

• See also “Changing the general settings

(PSM)” on page 25.

1Press and hold SEL (select) for more than

2 seconds so that one of the PSM items

appears on the display.

2Press ¢ or 4 to select “TA VOL”

(TA volume).

3Turn the control dial to set to the desired

volume.

You can set it from “VOL 00” to “VOL 50.”

4Press SEL (select) to finish the setting.

Automatic clock adjustment

When shipped from the factory, the clock built in

this unit is set to be readjusted automatically

using the CT (Clock Time) data in the RDS

signal.

If you do not want to use automatic clock

adjustment, follow the procedure below.

• See also “Changing the general settings

(PSM)” on page 25.

1Press and hold SEL (select) for more than

2 seconds so that one of the PSM items

appears on the display.

2Press ¢ or 4 to select “AUTO

ADJ” (adjustment).

3Turn the control dial counterclockwise to select

“OFF.”

Now automatic clock adjustment is canceled.

4Press SEL (select) to finish the setting.

To reactivate clock adjustment, repeat the

same procedure and select “ON” in step 3 by

turning the control dial clockwise.

Note:

You must stay tuned to the same station for more than

2 minutes after setting “AUTO ADJ” to “ON.”

Otherwise, the clock time will not be adjusted. (This is

because the unit takes up to 2 minutes to capture the

CT data in the RDS signal.)

Changing the display mode while

listening to an FM station

You can change the initial indication on the

display to station name (PS NAME) or station

frequency (FREQ) while listening to an FM RDS

station.

• See also “Changing the general settings

(PSM)” on page 25.

1Press and hold SEL (select) for more than

2 seconds so that one of the PSM items

appears on the display.

2Press ¢ or 4 to select “TU DISP”

(tuner display).

3Turn the control dial to set to the desired

indication (“PS NAME” or “FREQ”).

4Press SEL (select) to finish the setting.

Note:

By pressing D (DISP), you can change the display

while listening to an FM RDS station. Each time you

press the button, the following information appears on

the main display:

• Then, the display goes back to the original

indication in several seconds.

• For more details, see “To set the clock display

—CLOCK” on page 27.

Station name

(PS NAME)

Station frequency

(FREQ)

Programme type

(PTY)

EN12-18KS-LH60R[E_EX]f.p65 3/14/03, 9:12 AM17

18

ENGLISH

PTY codes

NEWS: News

AFFAIRS: Topical programmes expanding

on current news or affairs

INFO: Programmes which impart

advice on a wide variety of topics

SPORT: Sport events

EDUCATE: Educational programmes

DRAMA: Radio plays

CULTURE: Programmes on national or

regional culture

SCIENCE: Programmes on natural science

and technology

VARIED: Other programmes like comedies

or ceremonies

POP M: Pop music

ROCK M: Rock music

EASY M: Easy-listening music

LIGHT M: Light music

CLASSICS: Classical music

OTHER M: Other music

WEATHER: Weather information

FINANCE: Reports on commerce, trading,

the Stock Market, etc.

CHILDREN: Entertainment programmes for

children

SOCIAL: Programmes on social

activities

RELIGION: Programmes dealing with any

aspect of belief or faith, or the

nature of existence or ethics

PHONE IN: Programmes where people can

express their views either by

phone or in a public forum

TRAVEL: Programmes about travel

destinations, package tours,

and travel ideas and

opportunities

LEISURE: Programmes concerned with

recreational activities such as

gardening, cooking, fishing,

etc.

JAZZ: Jazz music

COUNTRY: Country music

NATION M: Current popular music from

another nation or region, in that

country’s language

OLDIES: Classic pop music

FOLK M: Folk music

DOCUMENT: Programmes dealing with

factual matters, presented in an

investigative style

The same programme can be received on different frequencies.

Programme 1

broadcasting on

frequency A Programme 1

broadcasting on

frequency E

Programme 1

broadcasting on

frequency B

Programme 1

broadcasting on

frequency D

Programme 1

broadcasting on

frequency C

EN12-18KS-LH60R[E_EX]f.p65 3/7/03, 7:09 PM18

19

ENGLISH

TAPE OPERATIONS

Listening to a cassette

You can play back type I (normal) tapes.

1

Open the control panel.

Note on One-Touch Operation:

When a cassette is already in the cassette

compartment, pressing TAPE (CD-CH) turns on

the unit and starts tape play automatically.

2

Insert a cassette into the cassette

compartment.

The unit turns on and

tape play starts

automatically.

3

Close the control panel by hand.

4

Select the tape direction.

Each time you press 23,

the tape direction changes

alternately between forward

() and reverse

().

To stop play and eject the cassette

Press 0.

Tape play stops, the control panel flips down. The

cassette automatically ejects from the cassette

compartment. The source changes to the

previously selected one.

If you change the source, tape play also stops

(without ejecting the cassette this time).

• You can also eject the cassette by pressing 0

while the unit is turned off.

To fast-forward and rewind a tape

To stop fast-forward and rewind at any

position on the tape, press 23.

Tape play starts from that position on the tape.

Notes:

• When one side of the tape reaches its end during

play, the other side of the tape automatically starts

playing. (Auto Reverse)

• When the tape reaches its end while fast-

forwarding, the tape direction will be changed

automatically.

Press and hold ¢ for

more than one second to

fast-forward the tape.

When the tape reaches its

end, the tape is reversed and

playback starts from the

beginning of the other side.

Press and hold 4 for more than one

second to rewind the tape.

When the tape reaches its end, playback of the

same side starts.

EN19-22KS-LH60R[E_EX]f.p65 3/7/03, 7:09 PM19

20

ENGLISH

Each time you press the buttons, the number

changes up to ±9.

When the beginning of the specified tune is

located, playback starts automatically.

Notes:

• While locating a specified tune:

– If the tape is rewound to its beginning, playback

starts from the beginning of that side.

– If the tape is fast-forwarded to the end, it is

reversed and played from the beginning of the

other side.

• In the following cases, the Multi Music Scan

function may not operate correctly:

– Tapes with tunes having long pianissimo

passages (very quiet parts) or non-recorded

portions between tunes.

– Tapes with short non-recorded sections.

– Tapes with high level of noise or humming

between tunes.

– Tapes with tunes recorded at low recording

levels.

– The Dolby NR setting does not match. For

example, if Dolby B NR is on and the tape was

recorded with no Dolby NR.

Press ¢ to locate a

tune ahead of the current

tune on the cassette.

Press 4 to locate a

tune before the current

tune on the cassette.

Ex.: When you locate three tunes ahead

of the current tune

To play back tapes recorded with the

Dolby B NR*

1Press M (MODE) to enter the functions

mode while listening to a tape.

“MODE” flashes on the upper part of the

display.

2Press (Dolby B), while “MODE” is still

flashing on the display so that the

(Dolby B) indicator lights up.

“DOLBY B” also appears on the display for

several seconds.

To cancel the Dolby B NR, repeat steps 1

and 2 again so that the (Dolby B) indicator

goes off.

* Manufactured under license from Dolby

Laboratories.

“Dolby” and the double-D symbol are

trademarks of Dolby Laboratories.

Finding the beginning of a

tune

Multi Music Scan (MMS) allows you to

automatically start playback from the beginning

of a specified tune. You can specify up to 9 tunes

ahead of or before the current tune.

During playback

Specify the tune you want to locate (how

many tunes ahead of or before the

current tune).

EN19-22KS-LH60R[E_EX]f.p65 3/7/03, 7:09 PM20

21

ENGLISH

Other convenient tape functions

Skipping the blank portions on the tape

You can skip blank portions between the tunes

(Blank Skip).

When this function is turned on, the unit fast-

forwards (skipping blank portions of 15 seconds

or more), to the next tune and starts playback.

• See also “Changing the general settings

(PSM)” on page 25.

1

Press and hold SEL (select) for more

than 2 seconds so that one of the

PSM items appears on the display.

(PSM: see page 26.)

2

Press ¢ or 4 to select

“B.SKIP” (blank skip).

3

Turn the control dial clockwise to

select “ON.”

Now Blank Skip is

activated.

4

Finish the setting.

To cancel Blank Skip, repeat the same

procedure and select “OFF” in step

3

by turning

the control dial counterclockwise.

EN19-22KS-LH60R[E_EX]f.p65 3/7/03, 7:09 PM21

22

ENGLISH

Prohibiting cassette ejection

You can prohibit cassette ejection and lock a

cassette in the cassette compartment.

While pressing TAPE (CD-CH), press and

hold for more than 2 seconds.

“NO EJECT” flashes on the display for about

5 seconds, and the cassette is locked and

cannot be ejected.

To cancel the prohibition and unlock the

cassette

While pressing TAPE (CD-CH), press and hold

again for more than 2 seconds.

“EJECT OK” flashes on the display for about

5 seconds, and the cassette is unlocked.

Note:

If you press 0 while cassette ejection is prohibited,

the control panel flips down, but the cassette

continues to play and cannot be ejected.

Playing the current tune repeatedly

You can play the current tune repeatedly

(Repeat Play).

1Press M (MODE) to enter the

functions mode while playing a

tune you want to hear over again

on a cassette.

“MODE” flashes on the upper

part of the display.

2Press RPT (repeat), while

“MODE” is still on the display, so

that “REPEAT” appears on the

display.

When the tune has been played, the tape is

automatically rewound to the beginning of that

tune and the same tune will be played again.

To cancel Repeat Play, repeat steps 1 and 2

again so that the RPT indicator goes off.

Note:

In the following cases, Blank Skip and Repeat Play

may not operate correctly:

– Tapes with tunes having long pianissimo passages

(very quiet parts) or non-recorded portions during

tunes.

– Tapes with short non-recorded sections.

– Tapes with high level noise or humming between

tunes.

– Tapes with tunes recorded at low recording levels.

– The Dolby NR setting does not match. For example,

if Dolby B NR is on and the tape was recorded with

no Dolby NR.

Lights up when Repeat Play is turned on.

EN19-22KS-LH60R[E_EX]f.p65 3/7/03, 7:09 PM22

23

ENGLISH

SOUND ADJUSTMENTS

Indication For: Preset values

BAS TRE LOUD

USER (Flat sound) 00 00 OFF

ROCK Rock or +03 +01 ON

disco music

CLASSIC Classical +01 –02 OFF

music

POPS Light music +04 +01 OFF

HIP HOP Funk or rap +02 00 ON

music

JAZZ Jazz music +02 +03 OFF

Note:

You can adjust each sound mode to your preference.

Once you make an adjustment, it is automatically

stored for the currently selected sound mode. See

“Adjusting the sound” on page 24.

Selecting preset sound modes

(C-EQ: custom equalizer)

You can select a preset sound mode (C-EQ:

custom equalizer) suitable to the music genre.

• There is a time limit in doing the following

procedure. If the setting is canceled before you

finish, start from step

1

again.

1

Press M (MODE) to enter the

functions mode.

“MODE” flashes on the upper

part of the display.

2

Press EQ (equalizer) while “MODE”

is still flashing on the display.

The last selected sound

mode is recalled and applied

to the current source.

3

Select the sound mode you want.

Each time you press the

button, the sound modes

change as follows:

Ex.: If you have selected “USER” previously

Ex.: When you select “ROCK”

CLASSIC

POPSHIP HOPJAZZ

USER ROCK

Sound mode indicator flashes.

Sound mode indicator flashes.

EN23-24KS-LH60R[E_EX]f.p65 3/14/03, 9:12 AM23

24

ENGLISH

2

Adjust the setting.

3

Repeat steps

1

and

2

to adjust the

other items.

To reset each sound mode to the factory

settings, repeat the same procedure and

reassign the preset values listed in the table on

page 23.

To increase the level or

turn on the loudness

To decrease the level or

turn off the loudness

Adjusting the sound

You can adjust the sound characteristics to your

preference.

1

Select the item you want to adjust.

Each time you press the

button, the adjustable items

change as follows:

Indication To do: Range

BAS*1Adjust the bass. –06 (min.)

|

+06 (max.)

TRE*1Adjust the treble. –06 (min.)

|

+06 (max.)

FAD*2Adjust the front R06 (Rear only)

and rear speaker |

balance. F06 (Front only)

BAL Adjust the left L06 (Left only)

and right speaker |

balance. R06 (Right only)

LOUD*1Boost low and high

frequencies to LOUD ON

produce a well- |

balanced sound LOUD OFF

at low volume level.

VOL*3Adjust the volume. 00 (min.)

|

50 (max.)

*1When you adjust the bass, treble, or loudness, the

adjustment you have made is stored for the

currently selected sound mode (C-EQ) including

“USER.”

*2If you are using a two-speaker system, set the fader

level to “00.”

*3Normally the control dial works as the volume

control. So you do not have to select “VOL” to

adjust the volume level.

Ex. 1: When you adjust “TRE” (treble)

Ex. 2: When you turn on the loudness

Equalization pattern changes

as you adjust the bass or treble.

VOL

(volume)

BAS

(bass)

TRE

(treble)

FAD

(fader)

BAL

(balance)

LOUD

(loudness)

EN23-24KS-LH60R[E_EX]f.p65 3/7/03, 7:10 PM24

25

ENGLISH

OTHER MAIN FUNCTIONS

3

Adjust the PSM item selected.

4

Repeat steps

2

and

3

to adjust the

other PSM items if necessary.

5

Finish the setting.

Changing the general settings

(PSM)

You can change the items listed on the next page

by using the PSM (Preferred Setting Mode)

control.

Basic Procedure

1

Press and hold SEL (select) for more

than 2 seconds so that one of the

PSM items appears on the display.

(See page 26.)

2

Select the PSM item you want to

adjust.

Ex.: When you select “LEVEL”

Ex.: When you select “AUDIO 2”

EN25-29KS-LH60R[E_EX]f.p65 3/7/03, 7:10 PM25

26

ENGLISH

Preferred Setting Mode (PSM) items

• For detailed operations of each PSM items, refer to the pages listed in the table.

Indications Selectable values/items Factory-preset See

settings page

CLOCK H Hour adjustment

CLOCK M Minute adjustment

24H/12H 24/12-hour time display

AUTO ADJ Automatic clock setting

CLOCK Clock display

TU DISP Tuner display

AF-REG Alternative frequency/

Regionalization reception

PTY STBY PTY standby

TA VOL Traffic announcement

volume

P-SEARCH Programme search

DAB AF*2Alternative frequency

search

DAB VOL*2DAB volume adjustment

LEVEL Level display

DIMMER Dimmer mode

TEL Telephone muting

BEEP Key-touch tone

SCROLL Scroll mode

B.SKIP Blank skip

EXT IN*3External component

TAG DISP Tag display

12H 24H

OFF ON

VOL 00 – VOL 50 VOL 20

OFF ON

AF OFF AF ON

VOL –12 VOL 12

OFF

AF ON

AUDIO 1 AUDIO 2 AUDIO 2

AF

OFF OFF

VOL 00

OFF

OFF MUTING 1

MUTING 2

OFF

29 programme types

(see page 18)

AF AF REG

OFF*1

24H

ON

PS NAME

PS NAME FREQ

17

27

17

12, 13

14

17

16

39

39

27

27

OFF ON ON 28

CHANGER LINE IN CHANGER 28

ONONOFF

8

*1Displayed only when the “DAB AF” is set to “AF OFF.”

*2Displayed only when the DAB tuner is connected.

*3Displayed only when one of the following sources is selected—FM, AM, and TAPE.

AUTO 27

AUTO OFF

ON

TAG OFF TAG ON TAG ON 28

ONCE 28

ONCE AUTO

OFF

OFF ON OFF 21

00 – 59

0 (0:00) 80 – 23 (1 – 12)

00 (0:00) 8

EN25-29KS-LH60R[E_EX]f.p65 3/7/03, 7:10 PM26

27

ENGLISH

To set the clock display—CLOCK

You can set the clock to be shown on the display

when the unit is turned on.

When shipped from the factory, the clock is set to

be shown on the display.

• ON: Clock display is turned on.

• OFF: Clock display is turned off. When

“OFF” is selected, the other

information (see table below)

appears instead of the clock

display (except when “LINE IN” is

selected as the source).

When CLOCK is set to OFF:

Source Initial Pressing D (DISP)

indication

Tuner Band

(FM/AM/

DAB)

TAPE “TAPE” or

or disc number

CD-CH

When CLOCK is set to ON:

Source Initial Pressing D (DISP)

indication

Tuner Clock Band appears for about

(FM/AM/ 5 seconds.

DAB)

TAPE Clock “TAPE” appears for

about 5 seconds.

CD-CH Clock Disc number and track/

file number appear

alternately each time

you press the button.

To select the level meter—LEVEL

You can select the level meter display according

to your preference.

When shipped from the factory, “AUDIO 2” is

selected.

• AUDIO 1: Shows the audio level indicator.

• AUDIO 2: Alternates “AUDIO 1” setting and

illumination display.

• OFF: Erases the audio level indicator.

To select the dimmer mode—DIMMER

When you turn on the car headlights, the display

automatically dims (Auto Dimmer).

When shipped from the factory, Auto Dimmer

mode is activated.

• AUTO: Activates Auto Dimmer.

• OFF: Cancels Auto Dimmer.

• ON: Always dims the display.

Note:

Auto Dimmer equipped with this unit may not work

correctly on some vehicles, particularly on those

having a control dial for dimming.

In this case, set the dimmer mode to “ON” or “OFF.”

To select the telephone muting—TEL

This mode is used when a cellular phone system

is connected. Depending on the phone system

used, select either “MUTING 1” or “MUTING 2,”

whichever mutes the sounds from this unit.

When shipped from the factory, this mode is

deactivated.

• MUTING 1: Selects this if this setting can mute

the sounds while using the cellular

phone.

• MUTING 2: Selects this if this setting can mute

the sounds while using the cellular

phone.

• OFF: Cancels the telephone muting.

Clock appears for about

5 seconds.

EN25-29KS-LH60R[E_EX]f.p65 3/7/03, 7:10 PM27

28

ENGLISH

To turn the tag display on or off

—TAG DISP

This function takes effect only when JVC

MP3-compatible CD changer is connected.

An MP3 file can contain file information called

“ID3 Tag” where its album name, performer, track

title, etc. are recorded.

There are two versions—ID3v1 (ID3 Tag version

1) and ID3v2 (ID3 Tag version 2). Only ID3v1 can

be shown.

When shipped from the factory, “TAG ON” is

selected.

• TAG ON: Turns on the ID3 tag display while

playing MP3 files.

• If an MP3 file does not have ID3

tags, folder name and file name

appear.

Note:

If you change the setting from

“TAG OFF” to “TAG ON” while

playing an MP3 file, the tag display

will be activated when the next file

starts playing.

• TAG OFF: Turns off the ID3 tag display while

playing MP3 files. (Only the folder

name and file name can be

shown.)

To turn on/off the key-touch tone—BEEP

You can deactivate the key-touch tone if you do

not want it to beep each time you press a button.

When shipped from the factory, the key-touch

tone is activated.

• ON: Activates the key-touch tone.

• OFF: Deactivates the key-touch tone.

To select the scroll mode—SCROLL

You can select the scroll mode for the disc

information (when the entire text cannot be

shown at once).

When shipped from the factory, scroll mode is set

to “ONCE.”

• ONCE: Scrolls only once.

• AUTO: Repeats the scroll (5-second

intervals in between).

• OFF: Cancels scroll mode.

Note:

Even if the scroll mode is set to “OFF,” you can scroll

the display by pressing D (DISP) for more than one

second.

To select the external component to use

—EXT IN

You can connect the external component to the

CD changer jack on the rear using the Line Input

Adapter KS-U57 (not supplied).

To use the external component as the playback

source through this unit, you need to select

which component—CD changer or external

component—to use.

When shipped from the factory, CD changer is

selected as the external component.

• CHANGER: To use the CD changer.

• LINE IN: To use the external component

other than CD changer.

Note:

For connecting the Line Input Adapter KS-U57 and

the external component, refer to the Installation/

Connection Manual (separate volume).

EN25-29KS-LH60R[E_EX]f.p65 3/7/03, 7:10 PM28

29

ENGLISH

Detaching the control panel

You can detach the control panel when leaving

the car.

When detaching or attaching the control panel,

be careful not to damage the connectors on the

back of the control panel and on the panel

holder.

Detaching the control panel

Before detaching the control panel, be sure to

turn off the power.

1

Unlock the control panel.

2

Pull the control panel out of the unit.

3

Put the detached control panel into

the provided case.

Attaching the control panel

1

Insert the right side of the control

panel into the groove on the panel

holder.

2

Press the left side of the control

panel to fix it to the panel holder.

Note on cleaning the connectors:

If you frequently detach the control panel, the

connectors will deteriorate.

To minimize this possibility, periodically wipe the

connectors with a cotton swab or cloth moistened

with alcohol, being careful not to damage the

connectors.

Connectors

EN25-29KS-LH60R[E_EX]f.p65 3/7/03, 7:10 PM29

30

ENGLISH

CD CHANGER OPERATIONS

We recommend that you use the JVC MP3-

compatible CD changer with your unit.

By using this CD changer, you can play back

your original CD-Rs (Recordable) and CD-RWs

(Rewritable) recorded either in audio CD format

or in MP3 format.

• You can also connect other CH-X series

CD changers (except CH-X99 and CH-X100).

However, they are not compatible with MP3

discs, so you cannot play back MP3 discs.

• You cannot use the KD-MK series CD

changers with this unit.

Before operating your CD changer:

• Refer also to the Instructions supplied with

your CD changer.

• If no discs are in the magazine of the CD

changer or the discs are inserted upside

down, “NO DISC” will appear on the display.

If this happens, remove the magazine and

set the discs correctly.

• If no magazine is loaded in the CD changer,

“NO MAG” appears on the display. If this

happens, insert the magazine in the CD

changer.

• If “RESET 1” – “RESET 8” appears on the

display, something is wrong with the

connection between this unit and the CD

changer. If this happens, check the

connection and make sure the cords are

connected firmly. Then, press the reset

button of the CD changer.

About MP3 discs

MP3 “files (tracks)” can be recorded in

“folders”—in PC terminology.

During recording, the files and folders can be

arranged in a way similar to arranging files and

folders of computer data.

“Root” is similar to the root of a tree. Every file

and folder can be linked to and be accessed from

the root.

Playing discs

Select the CD changer (CD).

*1If you have changed the “EXT IN” setting to

“LINE IN” (see page 28), you cannot select the CD

changer.

: Folders and their playback order

: MP3 files and their playback order

1

1

2

3

10

11

12

4

5

6

7

8

9

01

01

05

02 03

04

Hierarchy

ROOT

Level 1 Level 2 Level 3 Level 4 Level 5

TAPE CD*

1

EN30-34KS-LH60R[E_EX]f.p65 3/14/03, 9:12 AM30

31

ENGLISH

• When the current disc is an MP3 disc:

Playback starts from the first folder of the

current disc once file check is completed.

*2When “CLOCK” is set to “ON” (see page 27),

the current indication will soon change to the

clock time.

*3If some MP3 files are recorded without being

included in a folder, they are played back first

and “ROOT” appears as the folder name.

• When the current disc is a CD:

Playback starts from the first track of the

current disc.

*4When “CLOCK” is set to “ON” (see page 27),

the current indication will soon change to the

clock time.

CONTINUED ON THE NEXT PAGE

Notes:

• When you press TAPE (CD-CH), the power

automatically comes on. You do not have to press

to turn on the power.

• If you change the source, CD changer play also

stops. Next time you select the CD changer as the

source, CD changer play starts from where

playback has been stopped previously.

• When you start playing back a CD Text or an MP3

disc, disc information will automatically appear on

the display. (See the explanation that follows.)

To change the display information

While playing back an MP3 file or CD Text, you

can change the disc information shown on the

display.

Each time you press D (DISP), the

display changes to show the

following:

For MP3 discs

•When “TAG DISP” is set to “TAG ON” (initial

setting: see page 28)

*5If an MP3 file does not have ID3 tags, folder name

and file name appear. In this case, the TAG

indicator will not light up on the display.

Selected disc number*2

MP3 indicator (folder) indicator

Folder or album name*3

Elapsed playing time

Current track

number

Selected disc number*4

Album name / performer

(folder name* )

(TAG lights up on the display)

Track title (file name* )

(TAG lights up on the display)

Elapsed playing time and

Current file number

5

5

EN30-34KS-LH60R[E_EX]f.p65 3/7/03, 7:10 PM31

32

ENGLISH

Press ¢ briefly

during play, to skip ahead

to the beginning of the

next track/file.

Each time you press the

button consecutively, the

beginning of the next

tracks/files is located and

played back.

Press 4 briefly during play, to skip back to

the beginning of the current track/file.

Each time you press the button consecutively,

the beginning of the previous tracks/files is

located and played back.

•When “TAG DISP” is set to “TAG OFF”

For CD Text discs

Each time you press the button,

the display changes as follows:

Notes:

• The display shows up to 8 characters at one

time and scrolls if there are more than 8

characters.

See also “To select the scroll mode—SCROLL”

on page 28.

Some characters or symbols will not be shown

(and be blanked) on the display.

(Ex. “ABCå!d#” ]“ABCA D ”)

• When you press D (DISP) while playing an

audio CD, “NO NAME” appears for the disc

title/performer and the track title.

Press and hold ¢ ,

during play, to fast-forward

the track/file.

To go to a particular disc directly

Press the number button corresponding to the

disc number to start its playback (while the CD

changer is playing).

•To select a disc number from 1 – 6:

Press 1 (7) – 6 (12) briefly.

•To select a disc number from 7 – 12:

Press and hold 1 (7) – 6 (12) for more than

one second.

To fast-forward or reverse the track/file

Note:

During this operation on an MP3 disc, you can only

hear intermittent sounds. (The elapsed playing time

also changes intermittently on the display.)

To go to the next or previous tracks/files

Press and hold 4 ,

during play, to reverse the

track/file.

Folder name

( lights up on the display)

File name

( lights up on the display)

Elapsed playing time and

Current file number

Disc title / performer

Track title

( lights up on the display)

Elapsed playing time and

Current track number

EN30-34KS-LH60R[E_EX]f.p65 3/7/03, 7:10 PM32

33

ENGLISH

Press 5 (up) while playing an

MP3 disc, to go to the next

folder.

Each time you press the button

consecutively, the next folder is

located, and the first file in the

folder starts playback.

Press ∞ (down) while playing an MP3 disc, to go

to the previous folder.

Each time you press the button consecutively,

the previous folder is located, and the first file in

the folder starts playback.

How to go to the desired track/file quickly

• Ex. 1: To select track/file number 32 while

playing track/file number 6

• Ex. 2 : To select track/file number 8 while

playing track/file number 36

To skip to the next or previous folder

(only for MP3 discs)

(Three times) (Twice)

Track/file 6 \ 10 \ 20 \ 30 \ 31 \ 32

Track/file 36 \ 30 \ 20 \ 10 \ 9 \ 8

(Three times) (Twice)

This operation is only possible when

using JVC MP3-compatible CD changer

(CH-X1500).

To go to a track/file quickly

1Press M (MODE) to enter the functions mode

while playing a disc.

“MODE” flashes on the upper

part of the display.

2Press 5 (up) or ∞ (down) while still in the

functions mode.

* The first time you press 5 (up) or ∞ (down)

button, the track/file skips to the nearest

higher or lower track/file with a track/file

number of multiple ten (ex. 10th, 20th, 30th).

Then each time you press the button, you can

skip 10 tracks/files (see “How to go to the

desired track/file quickly” on the right column).

•After the last track/file, the first track/file will

be selected, and vice versa.

Note:

If the current playing disc is an MP3 disc, files are

skipped within the same folder.

To skip 10 tracks/files*

forwards to the last track/file

To skip 10 tracks/files*

backwards to the first track/file

EN30-34KS-LH60R[E_EX]f.p65 3/7/03, 7:10 PM33

34

ENGLISH

Selecting the playback modes

To play back tracks/files at random

(Folder Random/Disc Random/Magazine

Random Play)

1Press M (MODE) to enter the

functions mode during play.

“MODE” flashes on the upper part

of the display.

2Press RND (random), while

“MODE” is still flashing on the

display.

Each time you press the button, the

random play mode changes as

follows:

For MP3 discs:

For CDs:

Note:

The MP3 indicator also lights up if the current playing

disc is an MP3 disc.

*“FLDR RND” is only applicable for MP3 discs.

To play back tracks/files repeatedly

(Track Repeat/Folder Repeat/Disc Repeat

Play)

1Press M (MODE) to enter the

functions mode during play.

“MODE” flashes on the upper part

of the display.

2Press RPT (repeat), while “MODE”

is still flashing on the display.

Each time you press the button, the

repeat play mode changes as

follows:

For MP3 discs:

For CDs:

Note:

The MP3 indicator also lights up if the current playing

disc is an MP3 disc.

*“FLDR RPT” is only applicable for MP3 discs.

Mode Active Plays repeatedly

indicator

TRK RPT RPT indicator The current (or

lights up. specified) track/

file.

FLDR RPT* and RPT All files of the

indicators current (or

light up. specified) folder of

the current disc.

DISC RPT and RPT All tracks/files of

indicators light the current (or

up. specified) disc.

Mode Active Plays at random

indicator

FLDR RND* and RND All files of the

indicators current folder, then

light up. files of the next

folder and so on.

DISC RND and RND All tracks/files of

indicators the current (or

light up. specified) disc.

MAG RND RND indicator All tracks/files of

lights up. the inserted discs.

Ex.: When you select “MAG RND”

RND indicator

Ex.: When you select “DISC RPT”

(disc) and RPT indicators

Canceled

MAG RNDDISC RND

MAG RND

DISC RNDFLDR RND

Canceled

DISC RPT

TRK RPT FLDR RPT

Canceled

Canceled

DISC RPTTRK RPT

EN30-34KS-LH60R[E_EX]f.p65 3/7/03, 7:10 PM34

35

ENGLISH

EXTERNAL COMPONENT OPERATIONS

Playing an external component

You can connect the external component to the

CD changer jack on the rear using the Line Input

Adapter KS-U57 (not supplied).

Preparations:

• For connecting the Line Input Adapter KS-U57 and

the external component, refer to the Installation/

Connection Manual (separate volume).

• Before operating the external component using the

following procedure, select the external input

correctly. See “To select the external component to

use—EXT IN” on page 28.

1

Select the external component

(LINE IN).

• If “LINE IN”* does not appear on the display,

see page 28 and select the external input

(“LINE IN”).

*Displayed only when one of the following sources is

selected—FM, AM, and TAPE.

Note on One-Touch Operation:

When you press TAPE (CD-CH), the power

automatically comes on. You do not have to press

to turn on the power.

2

Turn on the connected component

and start playing the source.

3

Adjust the volume.

4

Adjust the sound characteristics as

you want. (See pages 23 and 24.)

TAPE LINE IN*

EN35-35KS-LH60R[E_EX]f.p65 3/7/03, 7:10 PM35

36

ENGLISH

DAB TUNER OPERATIONS

Tuning in to an ensemble and

one of the services

A typical ensemble has 6 or more programmes

(services) broadcast at the same time. After

tuning in to an ensemble, you can select a

service you want to listen to.

Before you start....

Press FM/AM (DAB) briefly if tape, CD changer,

or external component is the current source.

1

Select the DAB tuner.

Each time you press and

hold the button, the DAB

tuner and the FM/AM tuner

are alternately selected.

2

Select the DAB band (DAB1, DAB2,

or DAB3).

Each time you press the

button, the DAB band

changes as follows:

Note:

This receiver has three DAB bands (DAB1,

DAB2, DAB3). You can use any of them to tune

in to an ensemble.

We recommend that you use DAB (Digital Audio

Broadcasting) tuner KT-DB1500 or KT-DB1000

with your unit.

If you have another DAB tuner, consult your JVC

IN-CAR ENTERTAINMENT dealer.

• Refer also to the Instructions supplied with

your DAB tuner.

What is DAB system?

DAB is one of the digital radio broadcasting

systems available today. It can deliver CD

quality sound without any annoying

interference and signal distortion.

Furthermore, it can carry text, pictures, and

data.

In contrast to FM broadcast, where each

programme is transmitted on its own

frequency, DAB combines several

programmes (called “services”) to form one

“ensemble.”

In addition, each “service”—called “primary

service”—can also be divided into its

components (called “secondary service”).

With the DAB tuner connected with this unit,

you can enjoy these DAB services.

Note:

When reception switches between DAB and FM, the

listening volume level may increase or decrease

inconveniently. This change in the volume level results

from unequal audio injection levels at broadcaster

site, but not from the malfunction of this unit.

To prevent this inconvenience, you can adjust the DAB

volume level. (See “To adjust the DAB volume level”

on page 39.)

FM/AMDAB

DAB1

(D1)

DAB2

(D2)

DAB3

(D3)

EN36-39KS-LH60R[E_EX]f.p65 3/7/03, 7:11 PM36

37

ENGLISH

3

Start searching for an ensemble.

When an ensemble is received, searching

stops.

To stop searching before an ensemble is

received, press the same button you have

pressed for searching.

4

Select a service (either primary or

secondary) you want to listen to.

To change the display information while

tuning in to an ensemble

Normally service name is shown on the display.

If you want to check the ensemble name or its

frequency, press D (DISP).

Each time you press the button,

the following information appears

for a while in the main display.

To tune in to a particular ensemble

without searching

Before you start....

Press FM/AM (DAB) briefly if tape, CD changer,

or external component is the current source.

1Press and hold FM/AM (DAB) to select DAB

tuner as the source.

2Press FM/AM (DAB) repeatedly to select the

DAB band (DAB1, DAB2, or DAB3).

3Press and hold ¢ or 4 for more

than one second. “MANU” (manual) appears

on the display.

4Press ¢ or 4 repeatedly until the

ensemble you want is reached.

•If you hold down the button, the frequency

keeps changing until you release the button.

5Press 5 (up) or ∞ (down) to select a service

(either primary or secondary) you want to

listen to.

To restore the FM/AM tuner

Press and hold FM/AM (DAB) again.

Storing DAB services in

memory

You can preset up to 6 DAB services in each

DAB band (DAB1, DAB2, and DAB3) manually.

Before you start....

Press FM/AM (DAB) briefly if tape, CD changer,

or external component is the current source.

1

Select the DAB tuner.

Each time you press and

hold the button, the DAB

tuner and the FM/AM tuner

are alternately selected.

2

Select the DAB band (DAB1, DAB2,

or DAB3) you want.

Each time you press the

button, the DAB band

changes as follows:

To search for

ensembles of higher

frequency

To search for

ensembles of lower

frequency

To select the next service

(If a primary service has

some secondary services,

they are selected before

the next primary service is

selected.)

To select the previous service (either

primary or secondary)

CONTINUED ON THE NEXT PAGE

Service name

Ensemble name

Channel number

Frequency

FM/AMDAB

DAB1

(D1)

DAB2

(D2)

DAB3

(D3)

EN36-39KS-LH60R[E_EX]f.p65 3/7/03, 7:11 PM37

38

ENGLISH

3

Tune in to an ensemble you want.

4

Select a service of the ensemble you

want to listen to.

5

Press and hold the number button

(in this example, 1) you want to store

the selected service into for more

than 2 seconds.

6

Repeat the above procedure to store

other DAB services into other preset

numbers.

Notes:

•You can only preset primary DAB services. If you

store a secondary service, its primary service will

be stored instead.

•A previously preset DAB service is erased when a

new DAB service is stored in the same preset

number.

•Preset DAB services are erased when the power

supply to the memory circuit is interrupted (for

example, during battery replacement). If this

occurs, preset the DAB services again.

Tuning in to a preset DAB

service

You can easily tune in to a preset DAB service.

Remember that you must store services first. If

you have not stored them yet, “Storing DAB

services in memory” on pages 37 and 38.

Before you start....

Press FM/AM (DAB) briefly if tape, CD changer,

or external component is the current source.

1

Select the DAB tuner.

Each time you press and

hold the button, the DAB

tuner and the FM/AM tuner

are alternately selected.

2

Select the DAB band (DAB1, DAB2,

or DAB3) you want.

Each time you press the

button, the DAB band

changes as follows:

3

Select the number (1 – 6) for the

preset DAB service (primary) you

want.

Note:

If the selected primary service has some secondary

services, pressing the same number button repeatedly

will tune in to the secondary services.

To select the next service

To select the previous

service

Selected band/preset number and “MEMO”

(memory) appear alternately for a while.

FM/AMDAB

DAB1

(D1)

DAB2

(D2)

DAB3

(D3)

EN36-39KS-LH60R[E_EX]f.p65 3/7/03, 7:11 PM38

39

ENGLISH

What you can do more with

DAB

Tracing the same program automatically

(Alternative Reception)

You can keep listening to the same program.

•While receiving a DAB service:

When driving in an area where a service

cannot be received, this unit automatically

tunes in to another ensemble or FM RDS

station, broadcasting the same program.

•While receiving an FM RDS station:

When driving in an area where a DAB service

is broadcasting the same program as the

FM RDS station is broadcasting, this unit

automatically tunes in to the DAB service.

Note:

When reception switches between DAB and FM, the

listening volume level may increase or decrease

inconveniently. This change in the volume level results

from unequal audio injection levels at broadcaster

site, but not from the malfunction of this unit.

To prevent this inconvenience, you can adjust the DAB

volume level (see the right column).

To use Alternative Reception

When shipped from the factory, Alternative

Reception is activated.

•See also “Changing the general settings

(PSM)” on page 25.

1Press and hold SEL (select) for more than

2 seconds so that one of the PSM items

appears on the display.

2Press ¢ or 4 to select “DAB AF”

(alternative frequency).

3Turn the control dial to select the desired

mode.

• AF ON: Traces the program among DAB

services and FM RDS stations

—Alternative Reception. The AF

indicator lights up on the display

(see page 12).

• AF OFF: Alternative Reception is

deactivated.

4Press SEL (select) to finish the setting.

Note:

When Alternative Reception (for DAB services) is

activated, Network-Tracking Reception (for RDS

stations: see page 12) is also activated automatically.

On the other hand, Network-Tracking Reception

cannot be deactivated without deactivating

Alternative Reception.

To adjust the DAB volume level

You can adjust the volume level of DAB tuner

and store it in memory. By adjusting the volume

level properly to match it to the FM sound level,

you will not need to adjust the volume level each

time you change the source.

When shipped from the factory, DAB volume

level is set at “00.”

•See also “Changing the general settings

(PSM)” on page 25.

1Press and hold SEL (select) for more than

2 seconds so that one of the PSM items

appears on the display.

2Press ¢ or 4 to select “DAB VOL”

(DAB volume).

3Turn the control dial to set to the desired

volume.

You can set it from “VOL –12” to “VOL 12.”

4Press SEL (select) to finish the setting.

EN36-39KS-LH60R[E_EX]f.p65 3/7/03, 7:11 PM39

40

ENGLISH

TROUBLESHOOTING

What appears to be trouble is not always serious. Check the following points before calling a service

center.

Remedies

Adjust it to the optimum level.

Check the cords and

connections.

Press the reset button on the

panel holder after detaching the

control panel. (The clock setting

and preset stations stored in

memory are erased.)

(See page 2.)

Store stations manually.

Connect the aerial firmly.

Unlock the cassette.

(See page 22.)

Insert the cassette with the

exposed tape facing right.

Clean it with a head cleaning

tape.

Causes

The volume level is set to the

minimum level.

Connections are incorrect.

The built-in microcomputer

may have functioned

incorrectly due to noise, etc.

Signals are too weak.

The aerial is not connected

firmly.

Cassette is locked.

You have tried to insert a

cassette in the wrong way.

This is not a malfunction.

The tape head is dirty.

Symptoms

• Sound cannot be heard

from the speakers.

• This unit does not work at

all.

• SSM (Strong-station

Sequential Memory)

automatic preset does not

work.

• Static noise while listening

to the radio.

• A cassette tape cannot be

ejected.

• A cassette tape cannot be

inserted.

• Cassette tapes become

hot.

• Tape sound is at very low

level and sound quality is

degraded.

Tape Playback General

FM/AM

EN40-43KS-LH60R[E_EX]f.p65 3/7/03, 7:11 PM40

41

ENGLISH

CD Changer

Remedies

Insert discs into the

magazine.

Insert discs correctly.

Insert playable discs.

Insert the magazine.

Insert a disc that contains

MP3 files.

Add the extension code

—mp3 to their file names.

Change the disc.

(Record MP3 files using a

compliant application.)

Skip to another file or change

the disc. (Do not add the

extension code—mp3 to non-

MP3 files.)

Do not use too many

hierarchies and folders. Also,

do not record any other types

of audio tracks together with

MP3 files.

Connect this unit and the

CD changer correctly and

press the reset button of the

CD changer.

Press the reset button of the

CD changer.

Press the reset button on the

panel holder after detaching

the control panel. (The clock

setting and preset stations

stored in memory are

erased.) (See page 2.)

Causes

No disc is in the magazine.

Discs are inserted upside down.

Discs are unplayable.

No magazine is loaded in the

CD changer.

The current disc does not

contain any MP3 files.

MP3 files do not have the

extension code—mp3 in their

file names.

MP3 files are not recorded in

the format compliant with ISO

9660 Level 1, Level 2, or Joliet.

The file played back is not an

MP3 file (although it has the

extension code—mp3).

Readout time varies due to the

complexity of the folder/file

configuration.

Playback order is determined

when the files are recorded.

This sometimes occurs during

play. This is caused by how the

files are recorded on the disc.

This unit is not connected to the

CD changer correctly.

The built-in microcomputer may

have function incorrectly due to

noise, etc.

Symptoms

• “NO DISC” appears on the

display.

• “NO MAG” appears on the

display.

• “NO FILES” appears on the

display.

• MP3 disc is skipped or

cannot be played back.

• Noise is generated while

playing an MP3 disc.

• A longer readout time is

required for an MP3 disc

(“CHECK” keeps flashing on

the display).

• MP3 files cannot be played

back as you have intended

them to play.

• Elapsed playing time is not

correct for an MP3 disc.

• “RESET 8” appears on the

display.

• “RESET 1” – “RESET 7”

appears on the display.

• The CD changer does not

work at all.

EN40-43KS-LH60R[E_EX]f.p65 3/7/03, 7:11 PM41

42

ENGLISH

MAINTENANCE

This unit requires very little attention, but you will

be able to extend the life of the unit if you follow

the instructions below.

To clean the head

• Clean the heads after every 10 hours of use

using a wet-type head cleaning tape (available

at an audio store).

When the head becomes dirty, you may realize

the following symptoms:

– Sound quality is reduced.

– Sound level decreases.

– Sound drops out.

• Do not play dirty or dusty tapes.

• Do not touch the highly-polished head with any

metallic or magnetic tools.

To keep the tape clean

• Always store the cassettes in their storage

cases after use.

• Do not store cassettes in the following places:

– Subject to direct sunlight

– With high humidity

– At extremely hot temperatures

CAUTION:

• Do not play the cassettes with peeling labels;

otherwise, they can damage the unit.

• Tighten tapes to remove slack since loose tape

may become entangled with the mechanism.

• Do not leave a cassette in the cassette

compartment after use, as the tape may become

slack.

The function below is also provided to ensure the

longer life of this unit.

Ignition key-off release/Ignition key-on

play

• Turning off the ignition key with a cassette in

the compartment automatically releases the

tape from the unit’s tapehead.

• Turning on the ignition key with a cassette in

the compartment starts playback automatically

if you turned off the ignition during tape play.

EN40-43KS-LH60R[E_EX]f.p65 3/7/03, 7:11 PM42

43

ENGLISH

SPECIFICATIONS

CASSETTE DECK SECTION

Wow & Flutter: 0.11% (WRMS)

Fast-Wind Time: 100 sec. (C-60)

Frequency Response (Dolby B NR OFF):

30 Hz to 16 000 Hz (Normal tape)

Signal-to-Noise Ratio: 56 dB (Normal tape)

(Dolby B NR ON): 65 dB

(Dolby B NR OFF): 56 dB

Stereo Separation: 40 dB

GENERAL

Power Requirement:

Operating Voltage: DC 14.4 V

(11 V to 16 V allowance)

Grounding System: Negative ground

Allowable Operating Temperature: 0°C to +40°C

Dimensions (W × H × D):

Installation Size (approx.):

182 mm × 52 mm × 150 mm

Panel Size (approx.):

188 mm × 58 mm × 12 mm

Mass (approx.):

1.5 kg (excluding accessories)

Design and specifications are subject to change

without notice.

AUDIO AMPLIFIER SECTION

Maximum Power Output:

Front: 50 W per channel

Rear: 50 W per channel

Continuous Power Output (RMS):

Front: 19 W per channel into 4 Ω, 40 Hz

to 20 000 Hz at no more than

0.8% total harmonic distortion.

Rear: 19 W per channel into 4 Ω, 40 Hz

to 20 000 Hz at no more than

0.8% total harmonic distortion.

Load Impedance: 4 Ω (4 Ω to 8 Ω allowance)

Tone Control Range:

Bass: ±10 dB at 100 Hz

Treble: ±10 dB at 10 kHz

Frequency Response: 40 Hz to 20 000 Hz

Signal-to-Noise Ratio: 70 dB

Line-Out Level/Impedance:

2.0 V/20 kΩ load (250 nWb/m)

Output Impedance: 1 kΩ

TUNER SECTION

Frequency Range:

FM: 87.5 MHz to 108.0 MHz

AM: (MW) 522 kHz to 1 620 kHz

(LW) 144 kHz to 279 kHz

[FM Tuner]

Usable Sensitivity:

11.3 dBf (1.0 µV/75 Ω)

50 dB Quieting Sensitivity:

16.3 dBf (1.8 µV/75 Ω)

Alternate Channel Selectivity (400 kHz):

65 dB

Frequency Response: 40 Hz to 15 000 Hz

Stereo Separation: 30 dB

Capture Ratio: 1.5 dB

[MW Tuner]

Sensitivity: 20 µV

Selectivity: 35 dB

[LW Tuner]

Sensitivity: 50 µV

EN40-43KS-LH60R[E_EX]f.p65 3/10/03, 11:20 AM43

EN, GE, FR, NL 0403KKSMDTJEIN

Having TROUBLE with operation?

Please reset your unit

Refer to page of How to reset your unit

Haben Sie PROBLEME mit dem Betrieb?

Bitte setzen Sie Ihr Gerät zurück

Siehe Seite Zurücksetzen des Geräts

Vous avez des PROBLÈMES de fonctionnement?

Réinitialisez votre appareil

Référez-vous à la page intitulée Comment réinitialiser votre appareil

Hebt u PROBLEMEN met de bediening?

Stel het apparaat terug

Zie de pagina met de paragraaf Het apparaat terugstellen

J

V

C

© 2003 VICTOR COMPANY OF JAPAN, LIMITED

Cover001AKS-LH60R[E_EX]f.p65 3/7/03, 7:08 PM2

1

53 mm

184 mm

KS-LH60R

Installation/Connection Manual

Einbau/Anschlußanleitung

Manuel d’installation/raccordement

Handleiding voor installatie/aansluiting

0403KKSMDTJEIN

EN, GE, FR, NL

GET0127-003A

[E/EX]

J

V

C

1

Control panel

Schalttafel

Panneau de commande

Bedieningspaneel

2

Trim plate

Frontrahmen

Plaque d’assemblage

Sierplaat

9

8

Trim plate

Frontrahmen

Plaque d’assemblage

Sierplaat

7

Sleeve

Halterung

Manchon

Huis

Mounting bolt

Befestigungsschraube

Boulon de montage

Bevestigingsbout

5

4

Dashboard

Armaturenbrett

Tableau de bord

Dashboard

Rubber cushion

Gummipuffer

Amortisseur en

caoutchouc

Rubberdop

Control panel

Schalttafel

Panneau de commande

Bedieningspaneel

See “ELECTRICAL CONNECTIONS.”

Siehe „ELEKTRISCHE ANSCHLÜSSE“.

Référez-vous “RACCORDEMENTS

ELECTRIQUES” .

Zie “ELEKTRISCHE VERBINDINGEN”.

6

3

Handle

Griff

Poignée

Hendel

Fuse

Sicherung

Fusible

Zekering

Slot

Schlitz

Fente

Sleuf

Lock Plate

Arretierplättchen

Plaque de verrouillage

Vergrendelingsplaat

Sleeve

Halterung

Manchon

Huis

ENGLISH

• This unit is designed to operate on 12 V DC,

NEGATIVE ground electrical systems.

INSTALLATION

(IN-DASH MOUNTING)

• The following illustration shows a typical installation.

However, you should make adjustments

corresponding to your specific car. If you have any

questions or require information regarding

installation kits, consult your JVC IN-CAR

ENTERTAINMENT dealer or a company supplying

kits.

DEUTSCH

• Dieses Gerät ist für einen Betrieb in elektrischen

Anlagen mit 12 V Gleichstrom und (–) Erdung

ausgelegt.

EINBAU

(IM ARMATURENBRETT)

• Die folgende Abbildung zeigt einen typischen

Einbau. Dennoch müssen Sie entsprechend Ihrem

jeweiligen Auto Anpassungen vornehmen. Bei

irgendwelchen Fragen oder wenn Sie Informationen

hinsichtlich des Einbausatzes brauchen, wenden

Sie sich an ihren JVC Autoradiohändler oder ein

Unternehmen das diese Einbausätze vertreibt.

FRANÇAIS

• Cet appareil est conçu pour fonctionner sur des

sources de courant continu de 12 V à masse

NEGATIVE.

INSTALLATION (MONTAGE

DANS LE TABLEAU DE BORD)

• L’illustration suivante est un exemple d’installation

typique. Cependant, vous devez faire les

ajustements correspondant à votre voiture

particulière. Si vous avez des questions ou avez

besoin d’information sur des kits d’installation,

consulter votre revendeur d’autoradios JVC ou une

compagnie d’approvisionnement.

1

Before mounting: Press (control panel

release button) to detach the control panel if

already attached.

* When shipped from the factory, the control

panel is packed in the hard case.

2

Remove the trim plate.

3

Remove the sleeve after disengaging the sleeve

locks.

1Stand the unit.

Note: When you stand the unit, be careful

not to damage the fuse on the rear.

2Insert the 2 handles between the unit and

the sleeve, as illustrated, to disengage the

sleeve locks.

3Remove the sleeve.

Note: Be sure to keep the handles for future

use after installing the unit.

4

Install the sleeve into the dashboard.

* After the sleeve is correctly installed into the

dashboard, bend the appropriate tabs to hold

the sleeve firmly in place, as illustrated.

5

Fix the mounting bolt to the rear of the unit’s

body and place the rubber cushion over the end

of the bolt.

6

Do the required electrical connections.

7

Slide the unit into the sleeve until it is locked.

8

Attach the trim plate.

Note: Ensure the recessed part is at the bottom.

If not, the control panel will not open completely.

9

Attach the control panel.

1

Vor dem Einbau: Drücken Sie (Freigabe der

Schalttafel), um die Arretierung der Schalttafel zu

lösen, sofern diese bereits angebracht ist.

* Bei der Auslieferung ab Werk ist die Schalttafel

im Etui verpackt.

2

Den Frontrahmen herausnehmen.

3

Die Halterung nach dem Entriegeln der

Halterungensperren abnehmen.

1Das Gerät aufstellen.

Hinweis: Beim Aufstellen des Geräts darauf

achten, daß die Sicherung auf der Rückseite

nicht beschädigt wird.

2Die 2 Griffe zwischen dem Gerät und der

Halterung wie abgebildet einstecken und die

Halterungensperren entriegeln.

3Die Halterung entfernen.

Hinweis: Sicherstellen, daß die Griffe für

künftigen Gebrauch nach dem Einbau des

Geräts aufbewahrt werden.

4

Die Halterung im Armaturenbrett einbauen.

* Nach dem korrekten Einbau der Halterung im

Armaturenbrett, die entsprechenden Riegel

umknicken, um die Halterung an ihrem Platz zu

sichern, siehe Abbildung.

5

Die Befestigungsschraube an der Rückseite des

Gerätekörpers befestigen und das Ende der

Schraube mit einem Gummipuffer abdecken.

6

Nehmen Sie die erforderlichen elektrischen

Anschlüsse vor.

7

Das Gerät in die Halterung schieben, bis es einrastet.

8

Befestigen Sie den Frontrahmen.

Hinweis: Vergewissern Sie sich, dass sich die

Aussparung an der Unterseite befindet. Ist dies

nicht der Fall, lässt sich die Bedienungsblende

nicht vollständig öffnen.

9

Die Schalttafel anbringen.

1

Avant le montage:

Appuyer sur (déblocage

du panneau de commande) pour éventeullement

détacher le panneau de commande.

* Lorsque ce panneau de commande sort d’usine,

il est rangé dans un étui de transport.

2Retirer la plaque d’assemblage.

3Libérer les verrous du manchon et retirer le manchon.

1

Poser l’appareil à la verticale.

Remarque:

Lorsque vous mettez l’appareil à la

verticale, faire attention de ne pas

endommager le fusible situé sur l’arrière.

2

Insérer les 2 poignées entre l’appareil et le

manchon comme indiqué pour désengagé les

verrous de manchon.

3

Retirer le manchon.

Remarque:

S’assurer de garder les poignées

pour une utilisation ultérieur, après l’installation

de l’appareil.

4Installer le manchon dans le tableau de bord.

* Après installation correcte du manchon dans le

tableau de bord, plier les bonnes pattes pour

maintenir fermement le manchon en place,

comme montré.

5Monter le boulon de montage sur l’arrière du corps

de l’appareil puis passer l’amortisseur en

caoutchouc sur l’extrémité du boulon.

6Réalisez les connexions électriques.

7Faire glisser l’appareil dans le manchon jusqu’à ce

qu’il soit verrouillé.

8Attachez la plaque d’assemblage.

Remarque:

Assurez-vous que la partie encastrée

est en bas. Sinon, le panneau de commande ne

pourra pas être ouvert complètement.

9Remonter le panneau de commande.

1

Voordat u aan de montage van het apparaat

begint: Druk op (het bedieningspaneel

vrijgeven) als u het bedieningspaneel wilt

loskoppelen indien dit aan de eenheid is

vastgekoppeld.

*Standaard wordt het bedieningspaneel bij het

verlaten van de fabriek los verpackt meegeleverd.

2

Verwijder de sierplaat.

3

Verwijder het huis nadat u de klemmen hebt

losgemaakt.

1Zet het apparaat rechtop.

Opmerking: Wanneer u het apparaat rechtop

zet, moet u erop letten dat u de zekering aan de

achterkant niet beschadigt.

2Plaats de 2 hendels, zoals afgebeeld, tussen het

apparaat en het huis, om de klemmen los te

maken.

3Verwijder het huis.

Opmerking: Bewaar de hendels nadat u het

apparaat hebt geïnstalleerd, zodat u ze ook in de

toekomst kunt gebruiken.

4

Installeer het huis in het dashboard.

*Nadat het huis op de juiste wijze in het dashboard

is geplaatst, moet u de palletjes, zoals afgebeeld,

stevig op hun plaats duwen.

5

Maak de bevestigingsbout aan de achterkant van het

apparaat vast en plaats de rubberdop over het uiteinde

van de bout.

6

Breng de vereiste elektrische verbindingen tot stand.

7

Schuif het apparaat in het huis totdat het vergrendeld is.

8

Bevestig een sierplaat.

Opmerking: Zorg dat het ingedeukte gedeelte onder

is. Het bedieningspaneel kan anders namelijk niet

geheel worden geopend.

9

Bevestig het bedieningspaneel.

NEDERLANDS

• Dit apparaat mag worden gebruikt bij elektrische

systemen die werken op 12 V gelijkstroom met negatieve

aarding.

INSTALLATIE (INBOUW IN

HET DASHBOARD)

• Op de volgende afbeelding kunt u zien hoe de installatie,

normaal gesproken, in zijn werk gaat. U moet echter bij

de installatie rekening houden met de bijzonderheden

van uw eigen auto. Neem bij vragen of voor meer

bijzonderheden over inbouwpakketten contact op met uw

JVC car audio dealer of een dealer of een bedrijf dat

inbouwpakketten levert.

TROUBLESHOOTING

•The fuse blows.

* Are the red and black leads connected correctly?

•Power cannot be turned on.

* Is the yellow lead connected?

•No sound from the speakers.

* Is the speaker output lead short-circuited?

•Sound is distorted.

* Is the speaker output lead grounded?

* Are the “–” terminals of L and R speakers grounded

in common?

•Unit becomes hot.

* Is the speaker output lead grounded?

* Are the “–” terminals of L and R speakers grounded

in common?

FEHLERSUCHE

• Die Sicherung brennt durch.

* Sind die roten und schwarzen Leitungen richtig

angeschlossen?

• Stromversorgung kann nicht eingeschaltet

werden.

* Ist die gelbe Leitung angeschlossen?

• Kein Ton aus den Lautsprechern.

*

Ist die Lautsprecherausgangsleitung kurzgeschlossen?

• Ton verzerrt.

* Ist die Lautsprecherausgangsleitung geerdet?

* Sind die (–) Anschlußklemmen der linken und

rechten Lautsprecher zusammen geerdet?

• Gerät wird heiß.

* Ist die Lautsprecherausgangsleitung geerdet?

* Sind die (–) Anschlußklemmen der linken und

rechten Lautsprecher zusammen geerdet?

EN CAS DE DIFFICULTES

• Le fusible saute.

* Les fils rouge et noir sont-ils racordés

correctement?

• L’appareil ne peut pas être mise sous tension.

*

Le fil jaune est-elle raccordée?

• Pas de son des enceintes.

* Le fil de sortie d’enceinte est-il court-circuité?

• Le son est déformé.

* Le fil de sortie d’enceinte est-il à la masse?

* Les bornes “–” des enceintes gauche et droit sont-

elles mises ensemble à la masse?

• L’appareil devient chaud.

* Le fil de sortie d’enceinte est-il à la masse?

* Les bornes “–” des enceintes gauche et droit sont-

elles mises ensemble à la masse?

PROBLEMEN OPLOSSEN

•De zekering slaat door.

*Zijn de rode en de zwarte draden op de juiste manier

aangesloten?

•De stroom kan niet worden ingeschakeld.

*Is de gele draad aangesloten?

•Er komt geen geluid uit de speakers.

*Is de uitgaande speakerdraad kortgesloten?

•Het geluid wordt vervormd.

*Is de uitgaande speakerdraad geaard?

*Zijn de “–” polen van de linker- en de rechterspeakers

gemeenschappelijk geaard?

•Het apparaat raakt verhit.

*Is de uitgaande speakerdraad geaard?

*Zijn de “–” polen van de linker- en de rechterspeakers

gemeenschappelijk geaard?

*

4

InstalKS-LH60R[E_EX]003A_f.p65 3/14/03, 10:50 AM1

2

• When installing the unit without using the sleeve

• Beim Einbau des Geräts ohne Halterung

• Lors de l’installation de l’appareil scans utiliser de manchon

• Wanneer u het apparaat zonder huis installeert

In a Toyota for example, first remove the car radio and install the unit in its place.

Zum Beispiel in einem Toyota zuerst das Autoradio ausbauen und dann das Gerät an seinem Platz einbauen.

Par exemple dans une Toyota, retirer d’abord l’autoradio et installer l’appareil à la place.

Voorbeeld: Bij een Toyota moet u eerst de autoradio verwijderen en daarna het apparaat installeren.

Removing the unit

• Before removing the unit, release the rear section.

1

Remove the control panel.

2

Remove the trim plate.

3

Insert the 2 handles into the slots, as shown.

Then, while gently pulling the handles away from

each other, slide out the unit. (Be sure to keep

the handles after installing it.)

Ausbau des Geräts

• Vor dem Ausbau des Geräts den hinteren Teil

freigeben.

1

Den Schalttafel abnehmen.

2

Den Frontrahmen herausnehmen.

3

Die 2 Griffe in die Schlitze wie gezeigt stecken.

Dann die Griffe behutsam auseinander ziehen

und das Gerät herausziehen. (Die Griffe nach

dem Einbau auf jeden Fall aufbewahren.)

Retrait de l’appareil

•

Avant de retirer l’appareil, libérer la section arrière.

1Retirer le panneau de commande.

2Retirer la plaque d’assemblage.

3Introduire les 2 poignées dans les fentes, comme

montré. Puis, tout en tirant doucement les

poignées écartées, faire glisser l’appareil pour le

sortir.

(S’assurer de conserver les poignées

après l’installation de l’appareil.)

Verwijderen van het apparaat

•Voordat u het apparaat verwijdert, moet u het

achtergedeelte losmaken.

1

Verwijder het bedieningspaneel.

2

Verwijder de sierplaat.

3

Plaats de 2 hendels, zoals afgebeeld, in de sleuven.

Daarna duwt u de hendels zachtjes uit elkaar en kunt u

het apparaat naar buiten schuiven. (Bewaar de

hendels nadat u het apparaat hebt

geïnstalleerd!)

RACCORDEMENTS ELECTRIQUES

Pour éviter tout court-circuit, nous vous

recommandons de débrancher la borne négative de

la batterie et d’effectuer tous les raccordements

électriques avant d’installer l’appareil. Si l’on n’est pas

sûr de pouvoir installer correctement cet appareil, le

faire installer par un technicien qualifié.

Remarque:

Cet appareil est conçu pour fonctionner sur des

sources de courant continu de

12 V à masse

NEGATIVE

. Si votre véhicule n’offre pas ce type

d’alimentation, il vous faut un convertisseur de

tension, que vous pouvez acheter chez un revendeur

d’autoradios JVC.

•

Remplacer le fusible par un de la valeur précisée. Si

le fusible saute souvent, consulter votre revendeur

d’autoradios JVC.

•

Si le bruit est un problème...

Cet appareil incorpore un filtre de bruit dans le

circuit d’alimentation. Cependant, avec certains

véhicules, quelques claquements ou autres bruits

non désirés risquent de se produire. Si cela arrive,

raccorder la

borne arrière de masse

de l’appareil

au châssis de la voiture (voir le diagramme de

raccordement) en utiliscant des cordons les plus

gros et les plus courts possibles telle qu’une barre

de cuivre ou une tresse. Si le bruit persiste,

consulter votre revendeur d’autoradios JVC.

•

La puisscance admissible des enceintes devrait

supérieure à 50 W à l’arrière et à 50 W l’avant, avec

une impédance de

4 Ω à 8 Ω

.

• S’assurer de raccorder la mise à la masse de

cet appareil au châssis de la voiture.

•

Le dissipateur de chaleur devient très chaud après

usage. Faire attention de ne pas le toucher en

retirant cet appareil.

ELEKTRISCHE ANSCHLÜSSE

Zur Vermeidung von Kurzschlüssen empfehlen wir,

daß Sie den negativen Batterieanschluß abtrennen

und alle elektrischen Anschlüsse herstellen, bevor

das Gerät eingebaut wird. Sind Sie sich über den

richtigen Einbau des Geräts nicht sicher, lassen Sie

es von einem qualifizierten Techniker einbauen.

Hinweis:

Dieses Gerät ist für einen Betrieb in elektrischen

Anlagen mit 12 V Gleichstrom und (–) Erdung

ausgelegt. Verfügt Ihr Fahrzeug nicht über diese

Anlage, ist ein Spannungsinverter erforderlich, der

bei JVC Autoradiohändler erworben werden kann.

• Die Sicherung mit einer der entsprechenden

Nennleistung ersetzen. Brennt die Sicherung

häufig durch, wenden Sie sich an ihren JVC

Autoradiohändler.

• Sind Störgeräusche ein Problem...

Dieses Gerät enthält ein Störfilter im Stromkreis. Bei

manchen Fahrzeugen kann jedoch ein Klicken

oder andere unerwünschte Störgeräusche

auftreten. Sollte das der Fall sein, die hintere

Erdungscanschlußklemme (siehe Schaltplan) des

Geräts am Fahrwerk des Fahrzeugs anschließen,

dabei kürzere und dickere Kabel wie

beispielsweise Kupfergeflechtdraht oder Stahldraht

verwenden. Bleibt Störgeräusch bestehen, wenden

Sie sich an Ihren JVC Autoradiohändler.

• Die maximale Eingangsleistung der Lautsprecher

sollte mehr als 50 W hinten und 50 W vorn bei einer

Impedanz von 4 Ω bis 8 Ω betragen.

•Sicherstellen, daß das Gerät am Fahrwerk

geerdet wird.

• Das Abstrahlblech wird nach dem Gebrauch sehr

heiß. Beim Ausbau des Geräts darauf achten, das

Abstrahlblech nicht zu berühren.

ELEKTRISCHE VERBINDINGEN

Om kortsluiting te voorkomen adviseren wij u om de

minpool van de accu los te maken en alle elektrische

verbindingen tot stand te brengen voordat u het apparaat in

de auto installeert. Als u niet zeker weet hoe u dit apparaat

moet installeren, kunt u dit beter door een daartoe

gekwalificeerde technicus laten doen.

Opmerking:

Dit apparaat mag worden gebruikt bij elektrische systemen

die werken op 12 V gelijkstroom met negatieve

aarding. Als uw auto niet is uitgerust met een dergelijk

systeem, is een spanningsomzetter vereist. Dit instrument

kan worden aangeschaft bij JVC car audio dealers.

• Vervang de zekering door een exemplaar met het

aangegeven vermogen. Als de zekering vaak doorslaat,

moet u uw JVC car audio dealer raadplegen.

• Als u geluidsproblemen hebt…

De krachtschakeling van dit apparaat heeft een ingebouwd

geluidsfilter. In sommige voertuigen zijn tikgeluiden of

andere ongewenste geluiden te horen. Als dit gebeurt,

moet u de massaklem aan de achterkant (zie

aansluitingsschema) aan het chassis van de auto

vastmaken met behulp van een kortere en dikkere kabel,

zoals kopermanteldraad of tellerkabel. Als het geluid niet

verdwijnt, moet u contact opnemen met uw JVC car audio

dealer.

• Het maximum ingangsvermogen van de speakers moet

achterin meer dan 50 W zijn en voorin 50 W, met een

impedantie van 4 Ω tot 8 Ω.

•Zorg ervoor dat dit apparaat door middel van een

aardkabel is verbonden met het chassis van de

auto.

• De warmte-opnemer kan na gebruik erg heet worden.

Raak de warmte-opnemer niet aan wanneer u dit apparaat

van zijn plaats haalt.

Note : When installing the unit on the mounting bracket, make sure to use the 6 mm-long screws. If longer screws are

used, they could damage the unit.

Hinweis : Beim Anbringen des Gerät an der Konsole sicherstellen, daß 6 mm lange Schrauben verwendet werden.

Werden längere Schrauben verwendet, können sie das Gerät beschädigen.

Remarque :

Lors de l’installation de l’appareil sur le support de montage, s’assurer d’utiliser des vis d’une longueur de 6 mm.

Si des vis plus longues sont utilisées, elles peuvent endommager l’appareil.

Opmerking : Wanneer u het apparaat aan de bevestigingsklem vastmaakt, moet u de 6 mm lange schroeven gebruiken. Als u langere

schroeven gebruikt, kan het apparaat worden beschadigd.

• When using the optional stay

• Beim Verwenden der Anker-Option

• Lors de l’utilisation du hauban en option

• Wanneer u de steun gebruikt (facultatief)

ELECTRICAL CONNECTIONS

To prevent short circuits, we recommend that you

disconnect the battery’s negative terminal and make all

electrical connections before installing the unit. If you

are not sure how to install this unit correctly, have it

installed by a qualified technician.

Note:

This unit is designed to operate on 12 V DC,

NEGATIVE ground electrical systems. If your vehicle

does not have this system, a voltage inverter is

required, which can be purchased at JVC IN-CAR

ENTERTAINMENT dealers.

• Replace the fuse with one of the specified rating. If

the fuse blows frequently, consult your JVC IN-CAR

ENTERTAINMENT dealer.

• If noise is a problem...

This unit incorporates a noise filter in the power

circuit. However, with some vehicles, clicking or other

unwanted noise may occur. If this happens, connect

the unit’s rear ground terminal (see connection

diagram) to the car’s chassis using shorter and

thicker cords, such as copper braiding or gauge wire.

If noise still persists, consult your JVC IN-CAR

ENTERTAINMENT dealer.

• Maximum input of the speakers should be more than

50 W at the rear and 50 W at the front, with an

impedance of 4 Ω to 8 Ω.

•Be sure to ground this unit to the car’s chassis.

• The heat sink becomes very hot after use. Be careful

not to touch it when removing this unit.

Heat sink

Abstrahlblech

Dissipateur de chaleur

Warmte-opnemer

Handles

Griffe

Poignées

Hendels

Washer (ø5)

Unterlegscheibe(ø5)

Rondelle (ø5)

Sluitring (ø5)

Lock nut (M5)

Sicherungsmutter (M5)

Ecrou d’arrêt (M5)

Contra-moer (M5)

Mounting bolt (M5 x 20 mm)

Befestigungsschraube (M5 x 20 mm)

Boulon de montage (M5 x 20 mm)

Bevestigingsbout (M5 x 20 mm)

Rubber cushion

Gummipuffer

Amortisseur en caoutchouc

Rubberdop

Teileliste für den Einbau und

Anschluß

Die folgenden Teile werden zusammen mit diesem

Gerät geliefert.

Nach ihrer Überprüfung, die Teile richtig einsetzen.

Liste des pièces pour l’installation et

raccordement

Les pièces suivantes sont fournies avec cet appareil.

Après vérification, veuillez les placer correctement.

Lijst van onderdelen die u bij

installatie en aansluiting nodig hebt

De volgende onderdelen worden bij het apparaat geleverd.

Installeer ze op de juiste wijze, nadat u ze hebt

gecontroleerd.

Parts list for installation and

connection

The following parts are provided with this unit.

After checking them, please set them correctly.

Hard case/Control panel

Etui/Schalttafel

Etui de transport/Panneau de

commande

Behuizing/Bedieningspaneel

Sleeve

Halterung

Manchon

Huis

Trim plate

Frontrahmen

Plaque d’assemblage

Sierplaat

Power cord

Stromkable

Cordon d’alimentation

Stroomkabel

321

Control panel

Schalttafel

Panneau de commande

Bedieningspaneel

Trim plate

Frontrahmen

Plaque d’assemblage

Sierplaat Handle

Griff

Poignée

Hendel

Bracket*

Konsole*

Support*

Console*

Bracket*

Konsole*

Support*

Console*

* Not included with this unit.

* Nicht Teil dieses Geräts.

* Non fourni avec cet appareil.

* Niet meegeleverd.

Flat type screws (M5 x 6 mm)*

Senkkopfschrauben (M5 x 6 mm)*

Vis à tête plate (M5 x 6 mm)*

Platkopschroeven (M5 x 6 mm)*

Pocket

Taschen

Poche

Zak

Flat type screws (M5 x 6 mm)*

Senkkopfschrauben (M5 x 6 mm)*

Vis à tête plate (M5 x 6 mm)*

Platkopschroeven (M5 x 6 mm)*

Install the unit at an angle of less

than 30˚.

Stellen Sie das Gerät mit einem

Winkel von weniger als 30˚ auf.

Installez l’appareil avec un angle de

moins de 30˚.

Installeer het toestel met een hoek

kleiner dan 30˚.

Less than 30˚

Weniger als 30˚

Moins de 30˚

Kleiner dan 30˚

Sleeve

Halterung

Manchon

Huis

Screw (option)

Schraube (Option)

Vis (en option)

Schroef (facultatief)

Lock nut

Sicherungsmutter

Ecrou d’arrêt

Contra-moer

Stay (option)

Anker (Option)

Hauban (en option)

Steun (facultatief)

Mounting bolt

Befestigungsschraube

Boulon de montage

Bevestigingsbout

Fire wall

Feuerwand

Cloison

Brandscherm

Washer

Unterlegscheibe

Rondelle

Sluitring

Dashboard

Armaturenbrett

Tableau de bord

Dashboard

Battery

Batterie

Pile

Batterij

Remote controller

Fernbedienung

Télécommande

Afstandsbediening

CR2025

InstalKS-LH60R[E_EX]003A_f.p65 3/14/03, 10:50 AM2

3

7

2

3

4

6

1

3

*

*

2

15

B1 B3 B5 B7

B2 B4 B6 B8

A5 A7

A2 A4 A8

A6

B1 B3 B5 B7

B2 B4 B6 B8

A5 A7

A2 A4 A8

A6

1

A8

A7

A5

A4

A2

B5B6 B4 B3 B8 B7 B2 B1

5

A6

(ILLUMINATION)

Before connecting: Check the wiring in the vehicle

carefully. Incorrect connection may cause serious

damage to this unit.

The leads of the power cord and those of the

connector from the car body may be different in

color.

1

Connect the colored leads of the power cord to

the car battery, speakers and power aerial (if any)

in the following sequence.

1Black: ground

2Yellow: to car battery (constant 12 V)

3Red: to an accessory terminal

4Blue with white stripe: to remote lead of other

equipment or power aerial if any (200 mA max.)

5Orange with white stripe: to car light control

switch

6Brown: to cellular phone system (For details,

refer to the instructions of the cellular phone.)

7Others: to speakers

2

Connect the aerial cord.

3

Finally connect the wiring harness to the unit.

Note: If your vehicle does not have any accessory

terminal, move the fuse from the fuse position 1

(initial position) to fuse position 2, and connect the

red lead (A7) to the positive (+) battery terminal.

•The yellow lead (A4) is not used in this case.

Vor dem Anschließen: Die Verdrahtung im Fahrzeug

sorgfältig überprüfen. Falsche Anschlüsse können

ernsthafte Schäden am Gerät hervorrufen.

Die Leiter des Stromkabels und die Leiter des Anschlusses

im Fahrzeug können sich farblich unterscheiden.

1

Die farbigen Leitungen des Spannunsgversorgungskabels

an der Autobatterie, ontstekingsschakelaarden

Lautsprechern und dem Motorantenne (sofern vorhanden)

in folgender Reihenfolge anschließen.

1Schwarz: Erdung

2Gelb: an Autobatterie (konstant 12 V)

3Rot: zur einer Zubehöranschlußklemme

4Blau mit weißem Streifen: zum Zusatzkabel des

anderen Geräts oder der Motorantenne, sofern

vorhanden (max. 200 mA)

5Orange mit weißem Streifen: zum Autolichtschalter

6Braun: an Mobiltelefon (Weitere informationen

entnehmen Sie bitte der Bedienungscanleitung

des Mobiltelefons.)

7Andere: zur Lautsprecher

2

Das Antennenkabel anschließen.

3

Die Kabelbäume am Gerät anschließen.

Hinweis: Verfügt Ihr Fahrzeug nicht über eine

Zubehöranschlußklemme, die Sicherung von der 1.

Sicherungsposition (Erstposition) in die 2.

Sicherungsposition versetzen, die rote Leitung (A7) an

der (+) Batterieanschlußklemme anschließen.

•

Die gelbe Leitung (A4) wird in diesem Fall nicht verwendet.

Avant de commencer la connexion:

Vérifiez

attentivement le câblage du véhicule. Une connexion

incorrecte peut endommager sérieusement l’appareil.

Le fil du cordon d’alimentation et ceux des connecteurs

du châssis de la voiture peuvent être différents en

couleur.

1Connectez les fils de couleur du cordon d’alimentation

à la batterie de la voiture, aux enceintes et à l’antenne

automatique (s’il y en a une) dans l’ordre suivant.

1

Noir: à la masse

2

Jaune: à la batterie de la voiture (12 V constant)

3

Rouge: à une borne accessoire

4

Bleu avec bande blanche: au fil de télécommande

de l’autre appareil ou à l’antenne automatique s’il

y en a une (200 mA max.)

5

Orange avec bande blanche: à l’interrupteur

d’éclairage de la voiture

6

Marron: à un système de téléphone cellulaire

(Pour les détails, se référer aux instructions du

téléphone cellulaire.)

7

Autres: aux enceintes

2Connectez le cordon d’antenne.

3Finalement, connectez le faisceau de fils à l’appareil.

Remarque:

Si votre véhicule ne possède pas de borne

accessoire, déplacez le fusible de la position de fusible

1 (position originale) à la position de fusible 2 et connectez

le fil rouge (A7) à la borne positive (+) de la batterie.

•Le fil jaune (A4) n’est pas utilisé dans ce cas.

Alvorens te verbinden: Controleer de bedrading in de

auto zorgvuldig. Het apparaat kan door verkeerde

verbinding ernstige schade oplopen. De draden van het

stroomsnoer verschillen mogelijk van kleur met de

aansluitingen op het chassis van de auto.

1

Sluit de gekleurde snoerdraden van de stroomkable in

de hierna genoemde volgorde aan op de accu van de

auto, de luidsprekers en de antenne (indien aanwezig).

1Zwart: aarde

2Geel: naar de accu van de auto (constant 12 V)

3Rood: naar de aansluitklem van de accessoire

4Blauw met witte streep: naar

afstandsbedieningsdraad van andere apparatuur of

antenne met circuit indien aanwezig (200 mA max.)

5Oranje met witte streep: naar de schakelaar voor de

autoverlichting

6Bruin: naar het mobiele-telefoonsysteem (Lees voor

meer informatie de instructies die bij de mobiele

telefoon worden geleverd.)

7Andere: naar de speakers

2

Sluit de antenne aan.

3

Verbind de draadbundel daarna met het apparaat.

Opmerking: Als uw voertuig niet beschikt over een

aansluitklem, moet u de zekering verplaatsen van stand 1

(beginstand) naar stand 2 en moet u de rode draad (A7) met

de pluspool (+) van de accu verbinden.

• In dit geval wordt de gele draad (A4) niet gebruikt.

Typical Connections / Typische Anschlüsse / Raccordements typiques / Normale verbindingen

Line out (see

diagram )

Schutz kappen

Signalausgang

(siehe Schaltplan )

Sortie de ligne

(voir le diagramme )

Uitgang (zie schema )

Fuse block

Sicherungsblock

Porte-fusible

Zekeringblok

To metallic body or chassis of the car

Zur metallenen Karosserie oder zum Fahrwerk des Autos

Vers corps métallique ou châssis de la voiture

Naar metalen ondergrond of chassis van de auto

To a live terminal in the fuse block connecting to the car battery

(bypassing the ignition switch)

Zur einer stromführenden Anschlußklemme im Sicherungsblock

zum Anschließen an die Autobatterie (Umgehen des

Zündschalters)

A une borne sous tension du porte-fusible connectée à la batterie

de la voiture (en dérivant l’interrupteur d’allumage)

Naar een onder spanning staande aansluitklem in het zekeringblok die is

aangesloten op de accu van de auto (u passeert de ontstekingsschakelaar)

To remote lead of other equipment or power aerial if any

Zum Zusatzkabel des anderen Geräts oder der Motorantenne, sofern vorhanden

Au fil de télécommande de l’autre appareil ou à l’antenne automatique s’il y en a une

Naar afstandsbedieningsdraad van andere apparatuur of antenne met circuit indien aanwezig

To an accessory terminal in the fuse block

Zur einer Zubehöranschlußklemme im Sicherungsblock

Vers borne accessoire du porte-fusible

Naar een aansluitklem in het zekeringblok

Red

Rot

Rouge

Rood

Yellow*1

Gelb*1

Jaune*

1

Geel *1

Aerial terminal

Antennenanschlußklemme

Borne de l’antenne

Aansluitpunt antenne

To aerial

Zur Antenne

A l’antenne

Naar de antenne

Rear ground terminal

Hintere

Erdungscanschlußklemme

Borne arrière de masse

Massaklem aan de

achterkant

Blue with white stripe

Blau mit weißem Streifen

Bleu avec bande blanche

Blauw met witte streep

*1 : Before checking the operation of this unit prior to

installation, this lead must be connected, otherwise

power cannot be turned on.

*1 : Vor der Überprüfung der Funktionsfähigkeit des Geräts

vor dem Einbau, muß diese Leitung angeschlossen

werden, da sonst die Stromversorgung nicht

eingeschaltet werden kann.

*1 : Pour vérifier le fonctionnement de cet appareil avant

installation, ce fil doit être raccordé, sinon l’appareil ne

peut pas être mis sous tension.

*1 : Voordat u controleert of het apparaat werkt (alvorens het te

installeren), moet deze draad aangesloten zijn. Als dit niet het

geval is, kan de stroom niet worden ingeschakeld.

White

Weiß

Blanc

Wit

Gray with black stripe

Grau mit schwarzem

Streifen

Gris avec bande noire

Grijs met zwarte streep

Green

Grün

Vert

Groen

Purple

Lila

Violet

Paars

White with black stripe

Weiß mit schwarzem

Streifen

Blanc avec bande noire

Wit met zwarte streep

Green with black stripe

Grün mit schwarzem

Streifen

Vert avec bande noire

Groen met zwarte streep

Purple with black stripe

Lila mit schwarzem

Streifen

Violet avec bande noire

Paars met zwarte streep

Left speaker (front)

Linker Lautsprecher (vorne)

Enceinte gauche (avant)

Linkerspeaker (voorin)

Right speaker (front)

Rechter Lautsprecher (vorne)

Enceinte droit (avant)

Rechterspeaker (voorin)

Left speaker (rear)

Linker Lautsprecher (hinten)

Enceinte gauche (arrière)

Linkerspeaker (achterin)

Right speaker (rear)

Rechter Lautsprecher (hinten)

Enceinte droit (arrière)

Rechterspeaker (achterin)

Gray

Grau

Gris

Grijs

15 A fuse / 15 A Sicherung /

Fusible 15 A

/

Zekering 15 A

Not included with this unit.

Wird nicht mit Gerät mitgeliefert.

Non fourni avec cet appareil.

Niet bij het apparaat inbegrepen.

*Ignition switch

Zündschalter

Interrupteur d’allumage

Contactschakelaar

FRANÇAIS

DEUTSCH NEDERLANDSENGLISH

Fuse position 2 / 2. Sicherungsposition /

Position de fusible 2

/ Zekering, stand 2

To cellular phone system

Zur Moblitelephon

A un système de téléphone

cellulaire

Naar het mobiele-telefoonsysteem

PRECAUTIONS on power supply and

speaker connections:

•DO NOT connect the speaker leads of the power

cord to the car battery; otherwise, the unit will

be seriously damaged.

•Connect the black lead (ground), yellow lead (to car

battery, constant 12 V), and red lead (to an

accessory terminal) correctly.

•BEFORE connecting the speaker leads of the

power cord to the speakers, check the speaker

wiring in your car.

– If the speaker wiring in your car is as

illustrated in Fig. 1 and Fig. 2 below, DO NOT

connect the unit using that original speaker wiring.

If you do, the unit will be seriously damaged.

Redo the speaker wiring so that you can connect

the unit to the speakers as illustrated in Fig. 3.

– If the speaker wiring in your car is as

illustrated in Fig. 3, you can connect the unit

using the original speaker wiring in your car.

– If you are not sure of the speaker wiring of your

car, consult your car dealer.

VORSICHTSMASSREGELN beim

Anschließen der Stromversorgung und

Lautsprecher:

•Die Lautsprecherleitungen des Netzkabels

NICHT an der Autobatterie anschließen, da

sonst das Gerät schwer beschädigt wird.

• Die schwarze Leitung (Erdung), die gelbe Leitung

(zur Autobatterie, konstant 12 V) und die rote Leitung

(zur Zubehöranschlußklemme) richtig anschließen.

• VOR dem Anschließen der Lautsprecherleitungen

des Spannunsgversorgungskabels an die

Lautsprecher, die Lautsprecherverdrahtung in

Ihrem Auto überprüfen.

–Ist die Lautsprecherverdrahtung wie unten in

„Fig. 1“ und „Fig. 2“ abgebildet, das Gerät

NICHT mit der Originalverdrahtung der

Lautsprecher anschließen, da sonst das Gerät

schwer beschädigt wird.

Die Lautsprecherverdrahtung erneuern, so daß

Sie das Gerät an den Lautsprechern wie in

„Fig. 3“ abgebildet anschließen können.

–Ist die Lautsprecherverdrahtung in Ihrem Auto

wie in „Fig. 3“ abgebildet, können Sie das Gerät

mit der Originalverdrahtung der Lautsprecher in

Ihrem Auto anschließen.

– Sind Sie sich über die Lautsprecherverdrahtung

in Ihrem Auto nicht sicher, wenden Sie sich an

Ihren Autohändler.

PRECAUTIONS sur l’alimentation et la

connexion des enceintes:

•NE CONNECTEZ PAS les fils d’enceintes du

cordon d’alimentation à la batterie; sinon,

l’appareil serait sérieusement endommagé.

•

Connectez correctement le fil noir (a la masse), le fil

jaune (a la batterie de la voiture,12 V constant) et le

fil rouge (à la prise accessoire).

•

AVANT de connecter les fils d’enceintes du cordon

d’alimentation aux enceintes, vérifiez le câblage

des enceintes de votre voiture.

–

Si le câblage des enceintes de votre voiture

est comme montré sur la Fig. 1 ou Fig. 2

ci-dessous,

NE CONNECTEZ PAS l’appareil en

utiliscant ce câblage original des enceintes. Si

vous le faites, l’appareil sera sérieusement

endommagé.

Recommencez le câblage des enceintes de façon

que vous puissiez connecter l’appareil aux

enceintes comme montré sur la Fig. 3.

–

Si le câblage des enceintes de votre voiture

est comme montré sur la Fig. 3,

vous pouvez

connecter l’appareil en utiliscant ce câblage

original d’enceintes pour votre voiture.

–Si vous n’êtes pas sûrs du câblage d’enceintes de

votre voiture, consulter le concessionnaire de

votre voiture.

VOORZORGSMAATREGELEN bij het

verbinden van de stroomkabeldraad

met de speakers:

•Verbind de speakerdraden van de stroomkabel

NIET met de accu van de auto; als u dit wel doet,

zal het apparaat ernstige schade oplopen.

• Sluit de zwarte draad (aarde), de gele draad (naar de accu

van de auto, constant 12 V) en de rode draad (naar de

aansluitklem van de accessoire) op de juiste wijze aan.

• VOORDAT u de speakerdraden van de stroomkabel met

de speakers verbindt, moet u de bedrading van de

speakers in uw auto controleren.

–Als de bedrading van de speakers eruitziet

zoals hieronder staat afgebeeld in Fig. 1 en

Fig. 2, mag het apparaat NIET worden aangesloten

met behulp van deze oorspronkelijke

speakerbedrading. Als u dat wel doet, zal het apparaat

ernstige schade oplopen.

Pas de bedrading van de speakers aan, zodat u het

apparaat met de speakers kunt verbinden, zoals staat

afgebeeld in Fig. 3.

– Als de bedrading van de speakers eruitziet

zoals staat afgebeeld in Fig. 3, kunt u het

apparaat aansluiten met behulp van de oorspronkelijke

speakerbedrading in uw auto.

– Als u twijfels hebt over de speakerbedrading in uw

auto, moet u contact opnemen met uw autodealer.

Brown / Braun /

Marron

/ Bruin

Black

Schwarz

Noir

Zwart

Fig. 2 Fig. 3Fig. 1

Fuse position 1 / 1. Sicherungsposition /

Position de fusible 1

/

Zekering, stand 1

To steering wheel remote controller

(see diagram )

An Lenkradfernbedienung

(siehe Schaltplan )

Pour la télécommande de volant

(voir le diagramme )

Naar stuurwiel-afstandsbediening

(zie schema )

We recommend you to connect the

JVC MP3-compatible CD changer.

You can also connect other CH-X

series CD changers (except

CH-X99 and CH-X100).

•You cannot use the KD-MK series

CD changers with this unit.

You can also use an external

component such as a portable MD

player by connecting the Line Input

Adapter KS-U57 (not supplied).

(See diagram .)

Wir empfehlen Ihnen, den MP3-

kompatiblen CD-Wechsler von

JVC anzuschließen. Sie können

auch andere CD-Wechsler der

Serie CH-X anschließen (außer

CH-X99 und CH-X100).

• CD-Wechsler der Serie KD-MK

können mit diesem Gerät nicht

verwendet werden.

Sie können auch eine externe

Komponente, z.B. einen tragbaren

MD-Spieler, verwenden, wenn Sie den

(nicht zum Lieferumfang gehörenden)

Line-Eingangsadapter KS-U57

anschließen (siehe Schaltplan ).

Nous vous recommandons de

connecter le changeur de CD

compatible MP3 JVC. Vous pouvez

aussi connecter d’autres

changeurs de CD de la série CH-X

(sauf le CH-X99 et le CH-X100).

•Vous ne pouvez pas utiliser les

changeurs de CD de la série

KD-MK avec cet appareil.

Vous pouvez aussi utiliser un

appareil extérieur tel qu’un lecteur

de MD en connectant l’adaptateur

d’entrée de ligne KS-U57 (non

fourni). (Voir le diagramme ).

Sluit bij voorkeur de JVC, MP3

compatibele CD-wisselaar aan. U kunt

tevens bepaalde andere CD-wisselaars uit

de CH-X serie aansluiten (uitgezonderd

de CH-X99 en CH-X100).

• U kunt CD-wisselaars uit de KD-MK

serie niet met dit toestel gebruiken.

Het is ook mogelijk een extern

apparaat zoals een draagbare MD-

speler aan te sluiten met behulp van de

Line Input Adapter KS-U57 (niet

meegeleverd). (Zie schema .)

JVC CD changer/DAB tuner

or another external

component

CD-Wechsler von JVC/DAB-

Tuner oder eine andere

externe Komponente

Changeur CD JVC/Tuner

DAB ou autre appareil

extérieur

JVC CD-wisselaar/DAB-tuner

of een ander extern apparaat

Orange with white stripe

Orange mit weißem Streifen

Orange avec bande blanche

Oranje met witte streep

To car light control switch

Zum Autolichtschalter

A l’interrupteur d’éclairage de la voiture

Naar de schakelaar voor de autoverlichting

L

R+

-

+

-

+

-

+

-

L

R+

-

+

-

+

-

+

-

L

R+

-

+

-

+

-

+

-

InstalKS-LH60R[E_EX]003A_f.p65 3/14/03, 10:50 AM3

4

INPUT

R

L

L

R

L

R

L

R

*

2

R

L

R

*

2

L

INPUT

R

L

LINE

REAR FRONT

OUT

R

L

L

R

L

R

L

R

L

R

You can connect an amplifier and other equipment to

upgrade your car stereo system.

• Connect the remote lead (blue with white stripe) to

the remote lead of the other equipment so that it

can be controlled through this unit.

• For amplifier only:

– Connect this unit’s line-out terminals to the

amplifier’s line-in terminals.

–Disconnect the speakers from this unit,

connect them to the amplifier. Leave the

speaker leads of this unit unused. (Cover the

terminals of these unused leads with

insulating tape, as illustrated above.)

Sie können einen Verstärker oder ein anderes Gerät

anschließen, um Ihre Autostereoanlage zu erweitern.

• Schließen Sie das Fernbedienungskabel (blau mit

weißem Streifen) an das Fernbedienungskabel des

anderen Geräts an, so daß es über dieses Gerät

gesteuert werden kann.

• Nur für den Verstärker:

– Die Anschlußklemmen am Ausgang dieses Gerät

an den Anschlußklemmen des Eingangs des

Verstärkers anschließen.

–Die Lautsprecher von diesem Gerät abtrennen

und am Verstärker anschließen. Die

Lautsprecherleitungen dieses Geräts unbenutzt

lassen. (Die Anschlußklemmen dieser nicht

verwendeten Leitungen mit Isolierklebeband

umwickeln, siehe Abbidung oben.)

Vous pouvez connecter un amplificateur ou autre

appareil pour améliorer votre système autoradio.

•Connectez le fil de commande à distance (bleu

avec bande blanche) au fil de commande à

distance de l’autre appareil de façon qu’il puisse

être commandé via cet appareil.

•Pour l’amplificateur seulement:

–Raccorder les bornes de sortie ligne de cet appareil

aux bornes d’entrée ligne de l’amplificateur.

–

Déconnectez les enceintes de cet appareil et

connectez-les à l’amplificateur. Laissez les fils

d’enceintes de cet appareil inutilisés.

(Recouvrir les extrémités de ces fils inutilisés

avec de la bande isolante comme montré ci-

dessus.)

Het is mogelijk om uw autostereosysteem uit te breiden

met een versterker of andere apparatuur.

• Verbind de afstandsbedieningsdraad (blauw met witte

streep) met de afstandsbedieningsdraad van andere

apparatuur zodat deze op afstand via dit apparaat kan

worden bediend.

• Alleen voor een versterker:

– Verbind de uitgang van het apparaat met de ingang

van de versterker.

–Koppel de speakers van dit apparaat los en

verbind ze aan de versterker. Gebruik de

speakerdraden van dit apparaat niet. (Plak

de aansluitklemmen van deze

speakerdraden met isolatieband af zoals

hierboven is afgebeeld.)

Connections Adding Other Equipment / Anschlüsse zum Hinzufügen von anderer Ausrüstung / Raccordement pour ajouter d’autres appareils /

Aansluitingen voor het toevoegen van andere apparatuur

Amplifier / Verstärker / Amplificateur / Versterker

Twist the core wires when connecting.

Die Kerndrähte beim Anschließen verdrehen.

Torsader les âmes des fils en les raccordant.

Draai de kerndraden om elkaar heen wanneer u ze wilt aansluiten.

CAUTION / VORSICHT / PRECAUTION / LET OP!:

•To prevent short-circuit, cover the terminals of the UNUSED leads with insulating tape.

• Zur Vermeidung eines Kurzschlusses die Anschlußklemmen der NICHT VERWENDETEN Leitungen

mit Isolierklebeband umwickeln.

•Pour éviter les court-circuits, couvrir les

bornes des fils qui ne sont PAS UTILISÉS

avec de la bande isolante.

• Om kortsluiting te voorkomen, moet u de

aansluitklemmen van ONGEBRUIKTE

gekleurde draden met isolatieband bedekken.

Connecting the leads / Anschließen der Leitungen / Raccordement des fils / Aansluiting van de gekleurde draden

Signal cord (not supplied with this unit)

Einzelleitung (nicht mit diesem Gerät mitgeliefert)

Cordon de signal (non fourni avec cet appareil)

Signaalkabel (wordt niet bij dit apparaat geleverd)

Rear speakers

Hintere Lautsprecher

Enceintes arrière

Achterspeakers

KS-LH60R

To power aerial if any

Zur Motorantenne, sofern

vorhanden

Vers l’antenne automatique, s’il y

en a une

Naar de antenne (indien aanwezig)

Y-connector (not supplied with this unit)

Y-Anschluß (nicht mit diesem Gerät mitgeliefert)

Connecteur Y (non fourni avec cet appareil)

Y-connector (wordt niet bij dit apparaat geleverd)

Blue with white stripe

Blau mit weißem Streifen

Bleu avec bande blanche

Blauw met witte streep

Remote lead

Fernbedienungsleitung

Fil d’alimentation à distance

Afstandsbedieningsdraad

*2 : Firmly attach the ground wire to the metallic

body or to the chassis of the car—to the place

not coated with paint (if coated with paint,

remove the paint before attaching the wire).

Failure to do so may cause damage to the unit.

*2 : Verbinden Sie den Erdungsleiter mit der

Karosserie oder dem Rahmen des

Fahrzeugs. Die Kntaktstelle darf nicht lackiert

sein (sollte die Kontaktstelle lackiert sein,

entfernen Sie den Lack der Kontaktstelle,

bevor Sie den Leiter befestigen). Wenn der

Erdungsleiter nicht ordnungsgemäß

angeschlossen wird, kann dieses Gerät

beschädigt werden.

*2 : Attachez solidement le fil de mise à la masse

au châssis métallique de la voiture—à un

endroit qui n’est pas recouvert de peinture (s’il

est recouvert de peinture, enlevez d’abord la

peinture avant d’attacher le fil). L’appareil peut

être endommagé si cela n’est pas fait

correctement.

*2 : Bevestig de aardedraad goed met een metalen

onderdeel of het chassis van de auto—bevestig op

een niet-gelakt gedeelte (indien gelakt, schuur dan

af alvorens de draad te bevestigen). Het toestel kan

worden beschadigd indien de aardedraad niet goed

is aangesloten.

Sie können einen CD-Wechsler und/oder einen

DAB-Tuner (Tuner für digitalen Rundfunk) von JVC

anschließen.

• Weitere Informationen über den Anschluß können

Sie der Bedienungsanleitong entnehmen, die dem

jeweiligen Gerät beiliegt.

You can connect a JVC CD changer and/or a JVC

DAB (Digital Audio Broadcasting) tuner.

•For their connections, refer to the Instructions

supplied with them.

Vous pouvez connecter un changeur CD JVC et/ou

un tuner DAB (Digital Audio Broadcasting) JVC.

•Pour leurs connexions, référez-vous aux “Manuel

d’instructions” qui les accompagnent.

Het is mogelijk een JVC CD-wisselaar en/of JVC

DAB-tuner (Digital Audio Broadcasting) aan te sluiten.

• Zie de Gebruiksaanwijzing van deze apparaten voor

meer informatie over het tot stand brengen van deze

aansluiting.

CD changer and DAB tuner / CD-Wechsler und DAB-Tuner / Changeur CD et tuner DAB / CD-wisselaar en DAB-tuner

Connecting cord supplied with your DAB tuner

Verbindungskabel, das zum Lieferumfang des DAB-

Tuners gehört

Cordon de connexion fourni avec votre tuner DAB

Verbindingskabel die met de DAB-tuner wordt

meegeleverd

Connecting cord supplied with your CD changer

Verbindungskabel, das zum Lieferumfang des

CD-Wechsler gehört

Cordon de connexion fourni avec votre changeur CD

Verbindingskabel die met de CD-wisselaar wordt

meegeleverd

JVC CD changer

CD-Wechsler von JVC

Changeur CD JVC

JVC CD-wisselaar

JVC DAB tuner

DAB-Tuner von JVC

Tuner DAB JVC

JVC DAB-tuner

•You can connect both components in series as illustrated above.

• Es ist möglich, beide Komponenten in einer Serienschaltung entsprechend der obigen Darstellung

anzuschließen.

•Vous pouvez connecter les deux appareils en série comme montré ci-dessus.

• Beide apparaten zijn volgens bovenstaande illustratie in serie aan te sluiten.

or

oder

ou

of

JVC CD changer

CD-Wechsler von JVC

Changeur CD JVC

JVC CD-wisselaar

JVC DAB tuner

DAB-Tuner von JVC

Tuner DAB JVC

JVC DAB-tuner

Connecting cord supplied with your DAB tuner or CD changer

Verbindungskabel, das zum Lieferumfang des DAB-Tuners oder CD-Wechslers gehört

Cordon de connexion fourni avec votre tuner DAB ou changeur CD

Verbindingskabel die met de DAB-tuner of CD-wisselaar wordt meegeleverd

External Component / Externe Komponente / Appareil extérieur / Extern apparaat

Signal cord (not supplied with this unit)

Einzelleitung (nicht mit diesem Gerät mitgeliefert)

Cordon de signal (non fourni avec cet appareil)

Signaalkabel (wordt niet bij dit apparaat geleverd)

CD changer jack

Buchse für CD-Wechsler

Prise du changeur CD

Aansluiting voor CD-wisselaar

External component

Externe Komponente

Appareil extérieur

Extern apparaat

Line Input Adapter KS-U57 (not supplied with this unit)

Line-Eingangsadapter KS-U57 (nicht mit diesem Gerät mitgeliefert)

Adaptateur d’entrée de ligne KS-U57 (non fourni avec cet appareil)

Line Input Adapter KS-U57 (wordt niet bij dit apparaat geleverd)

CAUTION / VORSICHT / PRECAUTION / LET OP!:

•Before connecting the CD changer and/or the DAB tuner, make sure that the unit is turned off.

• Bevor Sie den CD-Wechsler und/oder den DAB-Tuner anschließen, vergewissern Sie sich, daß das

Gerät ausgeschaltet ist.

•Avant de connecter le changeur CD et/ou le tuner DAB, s’assurer que l’unité est éteinte.

• Zorg ervoor dat de apparaat is uitgeschakeld alvorens u de en/of DAB-tuner CD-wisselaar aansluit.

KS-LH60R

KS-LH60R

KS-LH60R

Front speakers

Vordere Lautsprecher

Enceintes avant

Voorspeakers

JVC Amplifier

JVC Verstärker

JVC Amplificateur

JVC Versterker

Front speakers

Vordere Lautsprecher

Enceintes avant

Voorspeakers

You can connect another power amplifier for front speakers.

Sie können einen anderen Leistungsverstärker für die vorderen Lautsprecher

anschließen.

Vous pouvez connecter un autre amplificateur de puissance pour les enceintes avant.

U kunt nog een eindversterker voor de voorspeakers aansluiten.

Connecting to the steering wheel remote controller / Anschluß an die Lenkradfernbedienung / Connexion de la télécommande de volant /

Verbinden met de stuurwiel-afstandsbediening

If your car is equipped with the steering wheel remote controller, you can operate this receiver using the controller.

To do it, a JVC’s OE remote adapter (not supplied) which matches with your car is required. Consult your JVC IN-CAR

ENTERTAINMENT dealer for details.

Wenn Ihr Fahrzeug mit einer Lenkradferndienung ausgestattet ist, können Sie damit diesen Receiver steuern. Hierfür

ist ein für Ihr Fahrzeug passender Radio-Lenkrad-Fernbedienungsadaption von JVC (nicht im Lieferumfang enthalten)

erforderlich. Für weitere Einzelheiten wenden Sie sich an Ihren JVC Autoradiohändler.

Si votre voiture est munie d’une télécommande de volant, vous pouvez commander cet autoradio en utilisant la

télécommande. Pour le faire, un adaptateur pour télécommande au volant (non fourni) correspondant à votre voiture est

nécessaire. Consultez votre revendeur d’autoradio JVC pour les détails.

Indien uw auto een stuurwiel-afstandsbediening heeft, kunt u deze receiver met die afstandsbediening bedienen. Hiervoor heeft u

echter een JVC adapter voor stuurwiel-afstandsbediening (niet bijgeleverd) nodig die geschikt is voor uw auto. Raadpleeg uw JVC

car audio dealer voor details.

KS-LH60R

Steering wheel remote input

Eingang für Lenkradfernbedienung

Entrée de la télécommande de volant

Ingang stuurwiel-afstandsbediening

OE remote adapter (not supplied)

Radio-Lenkrad-Fernbedienungsadaption (nicht im

Lieferumfang enthalten)

Adaptateur pour télécommande au volant (non fourni)

Adapter voor stuurwiel-afstandsbediening (niet bijgeleverd)

Steering wheel remote controller (equipped in the car)

Lenkradfernbedienung (im Fahrzeug installiert)

Télécommande de volant (installée dans la voiture)

Stuurwiel-afstandsbediening (in de auto)

Solder the core wires to connect them securely.

Die Kerndrähte anlöten, um sie fest anzuschließen.

Souder les âmes des fils pour les raccorder entre eux de façon sûre.

Soldeer de kerndraden zodat ze stevig vast zitten.

JVC Amplifier

JVC Verstärker

JVC Amplificateur

JVC Versterker

See the INSTRUCTIONS (separate volume) for how to use the

external component with this unit.

Informationen zur Verwendung der externen Komponente mit diesem

Gerät finden Sie in den BEDIENUNGSANLEITUNG (separates

Dokument).

Référez-vous aux “MANUEL D’INSTRUCTIONS” (manuel séparé)

pour savoir comment utiliser l’appareil extérieur avec cet appareil.

Zie de GEBRUIKSAANWIJZING (apart boekje) voor details aangaande het

gebruik van het externe component met dit toestel.

InstalKS-LH60R[E_EX]003A_f.p65 3/24/03, 10:10 AM4