KITCHENAID Dishwasher Manual L0701319
User Manual: KITCHENAID KITCHENAID Dishwasher Manual KITCHENAID Dishwasher Owner's Manual, KITCHENAID Dishwasher installation guides
Open the PDF directly: View PDF 
.
Page Count: 32
| Download | |
| Open PDF In Browser | View PDF |
KitchenAid DISHWASHER For questions about features, operation/performance, parts, accessories or service, call: 1-800-422-1230 or visit our website at www.kitchenaid.com In Canada, for assistance, installation or service, call: 1-800-807-6777 or visit our website at www.KitchenAid.ca LAVE-VAISSELLE Au Canada, pour assistance, installation ou service, composez ...... #iI191_!! DISHWASHER I' ¢,._,_I III._+'_'' ....... Io, le 1-800-807-6777 +;,; _ ou visitez notre site web & www.KitchenAid.ca ;> _]_(!+ 11111!IIiII!!I"I!_,i SAFETY ................................... 2 SECURITE DU LAVE-VAISSELLE ................. 17 PARTS AND FEATURES ................................. 3 PIECES ET CARACTERISTIQUES ................ 18 START-UP ........................................................ 5 MISE EN MARCHE ......................................... 20 LOADING .......................................................... 6 CHARGEMENT 21 CYCLES AND OPTIONS ................................ 13 PROGRAMMES ............................................... ET OPTIONS ....................... 28 Save Water no pre-rinsing Economie d'eau sans prdrinKage Models/Modeles KUDS02SR, W10077956 KUDS02FR, KUDU02FR, KUDU02VSPA, KUDS02FSPA, KUDS021S, KUDS03FS DISHWASHER SAFETY Your safety and the safety of others are very important. We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages. This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING." These words mean: You can be killed or seriously injured if you don't immediately follow instructions. You can be killed or seriously injured if you don't follow instructions. All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed. Tip Over Hazard Do not use dishwasher until completely Electrical installed. Do not push down on open door. Doing so can result in serious injury or cuts. Electrically Shock Hazard ground dishwasher. Connect ground wire to green ground terminal box. Do not use an extension connector in cord. Failure to follow these instructions fire, or electrical shock. can result in death, PARTS AND FEATURES This manual covers several different models. The features on your dishwasher may vary from those shown below. K M B C D E F G j,- I iiiiiiiiiliiiiiiiiii A. 2-Position top rack adjuster (two) B. FLEXI-FOLD DOWN TM flexible tines C. Removable mid level rack D. SATINGLIDE '_ Ultra rack E. Model and serial number label E Water inlet opening (in tub wall) G. Removable lower level rack inserts (two) H. Detergent dispenser I. Vent J. Active vent K. Removable culinary tool rack L. SURE-HOLD '_cup and stemware holder M. Removable mid level rack inserts (two) N. SURE-HOLD '_light item clips (four) O. PROSCRUB®spray jets P Silverware basket Q. CULINARY CADDY ® utensil basket R. Overfill protection float S. Heating element 7_SURE-HOLD ® small items mesh pouch U. Rinse aid dispenser _Z WHISPER QUIET _ sound insulation system 14/.Control panel located on door KUDS02SR Heavy Duty • L ht/ C_ina • Normal • Quick Clean Up ® Rinse Only • ProSc • ...... ©ooooj ub Hi Temp Scrub • Sani Rinse • Heat Dry • 4 Hour Delay • ...... OOO®G Lock O San ized "...... '0"@_ Cancel O Clean KUDS02FR, KUDU02FR, KUDS03FS Duty Normal Q ...... C_ina • Clean O _k O O Up Only ProScrub Scrub Rinse Dry Delay • • • O Q Q • O O_ ...... O 00 O Control Lock O " " "Clean"S ........ Cancel KUDU02VSPA, KUDS02FSPA S eavy Light/ Duty Normal China Quick Clean Rinse Up Only Hi Temp Sani Heat 4 Hour Scrub Rinse Dry Delay ProScrub Q ................... • • START OControl Lock Resume OCleao Q ® Cancel OPTIONS KUDS021S O ControlLock Heavy Dusty N .... Light/ Quick China C ea=_nUp Ol_nly RinSer _._-,.o o o o O P ...... b Hi Temp Sani Scrub Rinse 4 Hour Heat Dry Washlng D_ay ooo'_.o o o o c_ Cancel 1 OClean San_t_zed PROGRESS _ START-UP Before using your dishwasher, remove all packaging materials. Read this entire Consumer Reference Guide, as well as the User Instructions. You will find important safety information and useful operating tips. NOTE: If the dishwasher is not started within 30 seconds after selecting the cycle and options, it will revert to the last cycle and options completed. For all models: 1. Rinse aid is essential for good drying. Be sure to fill the dispenser before you use your new dishwasher. Each filling will last about 1 to 3 months depending on your usage. IMPORTANT: 2= 3. • When the cycle starts, you will see a rotating pattern of lights in the display window indicating that the dishwasher is operating. This pattern will continue for up to 6 minutes while the multiple sensors check the incoming water temperature, rinse aid usage and soil level on dishes and cookware. The sensors then determine the ideal wash for your dish load. After sensing is complete, the display will show the number of minutes left in the cycle and the cycle countdown will begin. • The cycle countdown pauses while the dishwasher heats the water to a set temperature. (See "Cycle Selections.") Scrape large food soil and hard items (toothpicks or bones) from dishes. You do not need to prerinse your dishes. Properly load the dishwasher. (See "Loading.") Load dishes with space in between so water will reach the soiled surfaces. Make sure nothing keeps the spray arm(s) from spinning freely. \ 4. Add detergent. Always use a high-quality brand detergent. (See "Dishwasher Use" in the User Instructions.) For Models KUDS02FR, KUDU02FR, KUDS02FSPA and KUDS03FS: 5. Run hot water at the sink nearest your dishwasher until the water is hot. Turn off water. 6. Press the desired cycle and option selections on the control panel. (See "Cycles and Options.") KUDU02VSPA, 7. Press START/RESUME. Or press START/RESUME to repeat the same cycle and options as in the previous cycle. The selected cycle and option lights will glow. 8. Push door firmly closed within 3 seconds of pressing Start/ Resume. NOTE: If the dishwasher is not started within 30 seconds after selecting the cycle and options, it will revert to the last cycle and options completed. For model KUDS021S For Model KUDS02SR: 7. 7. Close the door firmly. Press START/RESUME on the front of the dishwasher door. Or press START/RESUME to repeat the same cycle and options as in the previous cycle. Close the door firmly. Press START/RESUME. Or press START/RESUME to repeat the same cycle and options as in the previous cycle. The selected cycle and option lights will glow. NOTE: If the dishwasher is not started within 30 seconds after selecting the cycle and options, it will revert to the last cycle and options completed. LOADING The culinary tool rack is designed with 2 movable baskets to hold extra silverware, knives and cooking utensils. Up position Removable Install the baskets in this up position when you have extra silverware and flatware to wash. culinary tool rack The removable culinary tool rack allows you to wash larger items in the mid level rack. IMPORTANT: Remove baskets prior to removing culinary tool rack from dishwasher. To remove the rack 1. 2. To access track stops, pull the rack forward until it stops. Remove both baskets by lifting them out of the rack. 3. To open track stops, flip the track stop to the outside of the track. Baskets installed in up position Down position Install the baskets in this down position when you have extra silverware, knives, or utensils requiring more room to wash. Track stop closed 4= Track stop open After opening both track stops, slide front wheels up and out of the slot in the track. Continue to pull rack forward in track and slide the back wheels up and out of the track. \ Baskets installed in down position IMPORTANT: When using the culinary tool baskets in the down position, the mid level rack must also be in the lowest position. Remove the front basket in the down position, when you are using the cup shelves or other tall items in the mid level rack for more room. Front basket removed while using cup shelves in mid level rack Remove front rack wheel. 5. 6. Remove back rack wheel. Close track stops. Slide rack tracks back into dishwasher. To replace the rack 1. Gently pull culinary tool rack tracks forward in dishwasher until they stop. 2. To open track stops, flip the track stop to the outside of the track. 3. Place the back rack rollers on each side of the culinary tool rack into the track slots and roll the rack back into the tracks. \ 4. • Place items so open ends face down for cleaning and draining. • Load glasses and cups in mid level rack only. The lower level rack is not designed for glasses and cups. Damage can occur. • Place cups and glasses in the rows between tines. Placing them over the tines can lead to breakage and water spots. Insert front rack rollers on each side of the rack into the track slots and slide rack partly back into the dishwasher. Cup and glass load 5. Close track stops on both sides of rack. China, crystal, and other delicate items must not touch each other during dishwasher operation. Damage may occur. Load plastic items in the mid level rack only. Only plastic items marked "dishwasher safe" are recommended. Load plastic items so the force of the spray does not move them during the cycle. To avoid chipping, do not let stemware touch other items. 6. Install baskets in the desired position. (See "Culinary Tool Rack.") Small bowls, pans, and other utensils can be placed in the mid level rack. Load bowls in the center section for best stability. Removable The mid level rack is designed for cups, glasses, and smaller items. Many items, up to 9" (22 cm), fit in the mid level rack. (See recommended loading patterns shown.) NOTE: The features on your dishwasher rack may vary from those in the drawings shown. mid level rack inserts Your dishwasher is shipped with 2 removable mid level rack inserts. (See illustration below.) The removable rack inserts allow you to adjust the rack for the type of load you are washing. This is useful when washing a variety of glassware and dishes. ................ 10 place setting A. Removable rack inserts B. Insert holding clips 12 place setting To remove inserts 1. Lift up on the insert wire located toward the center of the rack to release the insert from the holding clips. FLEXI-FOLD DOWN TM flexible tines The row of tines on the left-hand side of the mid level rack can be adjusted to make room for a variety of dishes. A. Lift removable insert wire to remove from holding clips. B. Holding clips 2. Lift insert out of rack. To install rack inserts 1. Place the insert end legs under the front or back rack wire as shown below. To 1. 2. 3. adjust the flexible tines Grasp the tip of the tine that is in the tine holder. Gently push the tine out of the holder. Lay the tines down, toward the center of the rack. SURE-HOLD _ cup and stemware holder Fold down the extra shelf on the left-hand or right-hand side of the mid level rack to hold additional cups, stemware or long items such as utensils and spatulas. NOTE: Remove the culinary tool basket(s) when washing tall stemware or other tall items in the mid level rack. A. Insert legs 2= Push down on the center insert wire until it slides into the holding clip on either side of the center in the bottom of the rack. SURE-HOLD c_light item clips The light item clips hold lightweight plastic items such as cups, lids, or bowls in place during washing. ,A To use a clip 1. Pull clip away from tine. 2. Insert item between tine and clip and release clip. A. Insert holding clips To move a clip 1. Pull the clip up and off the tine. 2. Reposition the clip on another tine. 3. Adjustable 2-position mid level rack After opening both track stops, slide front wheels up and out of the slot in track. Continue to pull rack forward in track and slide the back wheels up and out of the track. After removing the culinary tool rack (see "Removable culinary tool rack"), you can raise or lower the mid level rack to fit tall items in either the mid level or lower level rack. Raise the mid level rack to accommodate items up to 9" (22 cm) in the mid level rack and 13" (33 cm) in the lower level rack. Lower the mid level rack to accommodate items up to 11" (28 cm) in both the mid level and lower level racks. Adjusters are located on each side of the mid level rack. \ IMPORTANT: If using the culinary tool baskets in the Down position, the mid level rack must also be in the lowest position. Remove front rack wheel. 4. 5. Remove back rack wheel. Close track stops. Slide rack tracks back into dishwasher. To replace the rack 1. Gently pull rack tracks forward in dishwasher until they stop and click into place. 2. To open track stops, flip the track stop to the outside of the track. 3. Place the back rack rollers on each side of the rack into the track slot and roll the rack back into the tracks. To raise the rack Press both rack adjusters and lift the rack until it is in the up position and level. NOTE: The mid level rack adjusters must be level. To lower the rack Press both rack adjusters and slide the rack back to its lower position. Removable mid level rack \ The removable mid level rack allows you to wash larger items such as stock pots, roasters, and cookie sheets in the lower level rack. IMPORTANT: Remove dishes prior to removing the mid level rack from dishwasher. To remove the rack 1. To access track stops, pull the rack forward until it stops and clicks into place. 2. To open track stops, flip the track stop to the outside of the track. Track stop closed 4. Insert front rack rollers on each side of the rack into the rack slots. 5. Close track stops on both sides of rack. 6. Slide rack back into dishwasher. Track stop open Thelowerlevelrackisdesigned forplates, pans,casseroles, and utensils. Manyitems,upto13"(33cm)tall,fitinthelowerlevel rack.(Seerecommended loading patterns shown.) NOTE: Thefeatures onyourdishwasher rackmayvaryfromthose inthedrawings shown. • Loadcookie sheets, cakepans,andotherlargeitemsatthe sidesandback.Loading suchitemsinfrontcankeepthe watersprayfromreaching thedetergent dispenser. Mixed load 10 place setting • Secure heavily soiled cookware face down in the rack. • Make sure pot handles and other items do not stop rotation of the spray arm(s). The spray arm(s) must move freely. • Do not load items between the lower level rack and the side of the dishwasher tub because they might block the water inlet opening. PROSORUB _ wash area The PROSCRUB®wash area is located at the back of the lower level rack. NOTE: You must select the PROSCRUB®wash option to utilize this wash feature. Do not face items toward the rear of the dishwasher if you are not using this wash option. 12 place setting • Do not load glasses, cups, or plastic items in the lower level rack. Load small items in the lower level rack only if they are secured in place. • Load plates, soup bowls, etc., between tines. • Overlap the edges of plates for large loads. • Load soup, cereal, and serving bowls in the rack in a variety of ways depending upon their size and shape. Load bowls securely between the rows of tines. Do not nest bowls because the spray will not reach all surfaces. PROSCRUB_ wash area view in lower level rack (shown with rack pulled partially out of dishwasher) Load pans, casserole dishes, etc. in the back of the lower level rack with the soiled surfaces facing the PROSCRUB® spray jets. Make sure items do not interfere with the water feed tube or mid spray arm. Tip items toward the rear of the dishwasher in the wider space between the rows of tines in the double removable rack insert to maximize coverage. Utensil load IMPORTANT: Only one row of items may face the PROSCRUB®spray jets. Stacking, overlapping, or nesting items will keep the PROSCRUB®spray jets from reaching all of the surfaces. / tilt PROSCRUB® wash area side view 10 Removable lower level rack inserts The fold-down tines option on this insert gives you the flexibility to adjust your loading options for smaller plates and bowls to larger platters. Your dishwasher is shipped with 2 removable lower level rack inserts. (See illustration below.) The double and single removable rack inserts allow you to adjust the rack for the type of load you are washing. This is useful when washing a variety of dishes, pots and pans, or roasters. 2:-v Removing this insert allows you to wash larger items such as large mixing bowls, stock pots, and roasters. Single rack insert The single rack insert allows you to wash a number of medium-sized plates and bowls. A. Double rack insert B, Single rack insert Double rack insert The double rack insert allows you to wash a number of large plates, platters, and trays. IMPORTANT: This insert must be used when using the PROSCRUB®wash option. All insert tines should be in the up position, and the dish should be placed in the open, middle section facing the PROSCRUB®spray jets. To remove double and single inserts 1. Pull handle out to the right and lift up to release. 2. Lift insert out of rack. 11 To install double insert 2. Push down on insert until handle fits against outer rack edge. NOTE: It will be easier to install the inserts if you remove the silverware basket from the rack. 1. 41- Place the double insert end legs under the 3rd wire from the right as shown below. IMPORTANT: Make sure that the curved wires, on the bottom of the insert, fit over the wires in the bottom of the rack. 3. When center tab under handle locks in under the middle side rack wire, the insert is in place. (See illustration.) CULINARY CADDY e_utensil basket Use the utensil basket to hold specialty cooking utensils (serving spoons, spatulas, and similar items), or overflow silverware items. 2. Push down on insert until handle fits against outer rack edge. 41- 3. When center tab under handle locks in under the middle side rack wire, the insert is in place. (See illustration.) To install single insert 1. Place the single insert end legs under the 2nd wire from the right as shown below. IMPORTANT: Make sure the 3 hooks at the back of the insert are installed over the 2nd bottom rack wire from the front of the rack. The basket hangs on the bottom rack in the right-hand corner. Load the basket while it is on the bottom rack or remove the basket for loading on a counter or table. NOTE: Spin the spray arms. Be sure items in the basket do not stop the rotation of the spray arms. SURE-HOLD* small items mesh pouch This pouch hangs on the front of the bottom rack. Use it to hold small items that could otherwise "fly" around inside the dishwasher during a cycle. Load the silverware basket while it is in the bottom rack or take the basket out for loading on a counter or table. (See recommended loading pattern shown.) NOTE: Unload or remove the basket before unloading the racks to avoid spilling water droplets on the silverware. • A. 3 insert hooks B. Single insert end legs 12 Load items with covers down, using the slots, to avoid silverware nesting. Place small items such as baby bottle caps, jar lids, corncob holders, etc., in the section(s) with hinged cover(s). Close the cover to hold small items in place. Mix silverware IMPORTANT: Always load items (knives, skewers, etc.) pointing down. NOTES: A. Center cover open B. End covers closed • to avoid nesting when the cover Is up in the basket. When covers are up, mix items in each section of the basket with some pointing up and some down to avoid nesting. Spray cannot reach nested items • Do not load silver or silver-plated silverware with stainless steel. These metals can be damaged by contact with each other during washing. • Some foods (such as salt, vinegar, milk products, fruit juices, etc.) can pit or corrode silverware. Run a rinse cycle if you do not have a full load to wash immediately. CYCLES AND OPTIONS Select the wash cycle and options desired. Or press START/ RESUME to repeat the same cycle and options as in the previous cycle. NOTE: If the last cycle you completed was a rinse cycle, the dishwasher will run the last full wash cycle and options that you selected when you press Start/Resume. • If the power is off or the door is open for an extended period of time, the Start/Resume button memory will default to the Normal cycle with heated drying. • If you do not run the dishwasher daily, close the door to maintain memory. A "O" shows what steps are in each cycle. Temperatures indicate where extra heat is added. Water usage is shown in U.S. gallons/liters. This model meets the ENERGY STAR_ guidelines for energy efficiency. Cycle time includes dry time. An asterisk ( * ) by the cycle time indicates the cycle time might be longer depending on the temperature of the water entering the dishwasher. Normal Use this cycle for loads with normal amounts of food soil. (The energy-usage label is based on this cycle.) During the main wash, the wash action will repeatedly pause for several seconds. Use both detergent dispenser sections. PreWash Main Wash PreRinser Final Heated Rinse Dry Minimum Time (rain) Water Usage (gal/L) • • 105140°F (40.660°0) O* • 140°F (60°C) • 77* 3.9-7.1/ 14.7-27 Light/China Use this cycle for lightly soiled and delicate loads. During the heated dry, the heating element cycles on and off. Heavy Duty Use main detergent dispenser section. Use this cycle for heavily soiled pots, pans, casseroles, regular tableware and hard** water conditions. Rinse Main Wash PreRinser Final Heated Rinse Dry Minimum Time (rain) Water Usage (gal/L) • • 115°F * (46°C) O* • 135°F (57°C) • 72* 4.6-6.8/ 17-26 Use both detergent dispenser sections. PreWash Main Wash Rinse Final Heated Rinse Dry Minimum Time (rain) Water Usage (gal/L) • • 140°F * • • 140°F • 95* 6.9-7.8/ 26-30 (60oc) (60oc) 13 Quick Clean Up For Model KUDS02SR Use this cycle for a quick wash to clean dishes prior to entertaining. Towel drying may be needed. Anytime during a cycle, press CANCEL. The display shows Use main detergent dispenser section. Rinse Main Wash Rinse Final Heated Rinse • • • • Dry Minimum Time (rain) Water Usage (gal/L) 30* 6.9/26 Your dishwasher starts a 2-minute drain (if needed). Let the dishwasher drain completely. The light turns off after 2 minutes. NOTE: If your dishwasher does not need draining, the light turns off. Select a new cycle and options. Rinse Only Use this rinse cycle for rinsing dishes, glasses, and silverware that will not be washed right away. To stop the drain You can press CANCEL again to stop the drain immediately. sure to drain the dishwasher before starting a new cycle. Be Do not use detergent with this cycle. To clear the indicators PreWash Main Wash Rinse • Final Heated Rinse Dry Time (rain) Water Usage (gal/L) 10 1.8/7 Press CANCEL before starting the dishwasher to clear all options and cycles. For Models KUDS02FR, KUDU02FR, KUDS02FSPA, and KUDU02VSPA 1. A small amount of water is run through the pump to remove soil )articles between the main wash and final rinse. *If the incoming water temperature is less than the recommended temperature or food soils are heavy, the cycle will automatically compensate by adding time, heat, and water as needed. **Hard water is defined as 7 grains per U.S. gallon and above. NOTE: The sensor in your dishwasher monitors the soil level. Cycle time and/or water usage can vary from the numbers above as the sensor adjusts the cycle for the best wash performance. 2. 3. KUDS03FS, Open the door slightly to stop the cycle. Wait for the spraying action to stop before opening the door to gain access to the control panel. Press CANCEL. The Cancel light glows. Close the door firmly. The dishwasher starts a 2-minute drain (if needed). Let the dishwasher drain completely. To stop the drain Open the door and press CANCEL again. Be sure to drain the dishwasher before starting a new cycle. To clear the indicators Press CANCEL before starting the dishwasher to clear all options and cycles. For Model KUDS021S Anytime during a cycle, press CANCEL. The Cancel light glows. The dishwasher starts a 2-minute drain (if needed). Let the dishwasher drain completely. The light goes off when the dishwasher finishes the drain. To stop the drain You can press CANCEL again to stop the drain immediately. sure to drain the dishwasher before starting a new cycle. Be To clear the indicators Press CANCEL before starting the dishwasher to clear all options and cycles. For Model KUDS021S During the first minute of a cycle Press a new cycle and/or options. After the first minute of a cycle 1. Press CANCEL. The Cancel light glows. The dishwasher starts a 2-minute drain (if needed). Let the dishwasher drain completely. 2. Open the door. 3. 4. 5. 6. 14 Check the detergent dispensers, If the main wash cup has opened and the detergent washed away, refill the cups as needed. (See "Detergent Dispenser" in the User Instructions for more details.) Close the door. Press a new cycle and/or options, Press START/RESUME. The dishwasher resumes the new cycle and/or option after a 5-second pause, For Model KUDSO2SR You can add an item anytime before the main wash starts. Open the door and check the detergent dispenser. If the cover is still closed, you can add items. During the first minute of a cycle 1. Open the door. 2. 3. Press a new cycle and/or options. Check the detergent dispensers. They must be filled properly for the new cycle. (See "Detergent Dispenser" in the User Instructions for more details.) 4. 5. Close the door firmly. Press START/RESUME. The dishwasher resumes the new cycle and/or option after a 5-second pause. To add items for models KUDS02SR, 1. 2. 3. 4. After the first minute of a cycle 1. Press CANCEL. The display shows KUDSO21S Open the door slightly to stop the cycle. Wait for the spraying action to stop before opening the door. Open the door. If the detergent dispenser cover is still closed, add the item. Close the door firmly. Press START/RESUME. The dishwasher resumes the cycle after about a 5-second pause. To add items on all other models 1. 2. 3. 4. Your dishwasher starts a 2-minute drain (if needed). Let the dishwasher drain completely. The light turns off after 2 minutes. Open the door slightly to stop the cycle. Wait for the spraying action to stop before opening the door. Open the door. If the detergent dispenser cover is still closed, add the item. Press START/RESUME. Close the door firmly within 3 seconds of pressing Start/ Resume. The dishwasher resumes the cycle after about a 5-second pause. NOTE: If your dishwasher does not need draining, the light turns off. 2. 3. Open the door. Select a new cycle and/or options. 4. Check the detergent dispensers. They must be filled properly for the new cycle. (See "Detergent Dispenser" in the User Instructions for more details.) Close the door firmly. Press START/RESUME. The dishwasher resumes the new cycle and/or option after a 5-second pause. 5. 6. For Models KUDS02FR, KUDU02FR, KUDU02VSPA and KUDS03FS KUDS02FSPA, You can customize your cycles by pressing the options desired. If you change your mind, press the option again to turn off the option. Select a different option if desired. You can change an option anytime before the selected option begins. For example, you can press HEAT DRY anytime before drying begins. Press START/RESUME to repeat the same cycle and options as in the previous wash cycle. NOTE: If the last cycle you completed was a rinse cycle, when you press Start/Resume, the dishwasher runs the last full wash cycle and options. PROSCRUB_ wash option During the first minute of a cycle 1. Open the door. 2. Press a new cycle and/or options. 3. 4. 5. Check the detergent dispensers. They must be filled properly for the new cycle. (See "Detergent Dispenser" in the User Instructions for more details.) Press START/RESUME. Close the door firmly within 3 seconds of pressing Start/ Resume. The dishwasher resumes the new cycle and/or option after a 5-second pause. After the first minute of a cycle 1. Open the door slightly to stop the cycle. Wait for the spraying action to stop before opening the door to gain access to the control panel. 2. Press CANCEL. The Cancel light glows. 3. 4. 5. 6. 7. Select this option to activate the PROSCRUB®spray jets and provide intensified water spray to the back of the lower level rack. The PROSCRUB®wash option provides a concentrated wash action to pans, casseroles, etc. with tough food soil. This option may add heat and wash time to the cycle. NOTE: PROSCRUB®is an option with the Heavy Duty and Normal wash cycles. IMPORTANT: • Load pans, casserole dishes, etc. facing the PROSCRUB® spray jets in the back of the lower level rack. Tip items toward the rear of the dish rack to maximize coverage. Only one row of items may face the PROSCRUB®spray jets. Stacking, overlapping, or nesting items will keep the PROSCRUB® spray jets from reaching all of the surfaces. • Turn the PROSCRUB®wash option off if not loading items for this option. Close the door. Your dishwasher starts a 2-minute drain (if needed). Let the dishwasher drain completely. Open the door. Select a new cycle and/or options. Check the detergent dispensers. They must be filled properly for the new cycle. (See "Detergent Dispenser" in the User Instructions for more details.) Press START/RESUME. Close the door firmly within 3 seconds of pressing Start/ Resume. The dishwasher resumes the new cycle and/or option after a 5-second pause. Side view of PROSCRUB® wash area 15 Hi-Temp Scrub Select this option to heat the water during parts of the cycle, and add a rinse. Higher water temperatures and an extra rinse help clean tough soils. Hi-Temp Scrub, with the Heavy Duty cycle, heats the water in the main wash and the prewash. Hi-Temp Scrub, with the Normal cycle, raises the water temperature in the main wash. This option adds heat, water, and wash time to a cycle. NOTE: Hi-Temp Scrub is an option with the Heavy Duty and Normal cycles. Sani Rinse Select this option to raise the water temperature in the final rinse to approximately 155°F (68°C). The Sani Rinse option adds heat and time to the cycle. This high temperature rinse sanitizes your dishes and glassware in accordance with NSF/ANSI Standard 184 for Residential Dishwashers. Certified residential dishwashers are not intended for licensed food establishments. NOTE: The Heavy Duty cycle automatically uses this option. Sani Rinse is an option with the Normal cycle. Only these sanitization cycles have been designed to meet the NSF/ANSl requirements. 4 Hour Delay Select this option to run your dishwasher at a later time or during off-peak hours. You can add items to the load anytime during the delay countdown. (See "Adding Items During a Cycle.") The delay countdown will not continue if the door is not closed firmly. To delay the start (Model 1. Close the door. 2. 3. 4. Select option Press Press KUDS021S) a wash cycle and options. The selected cycle and lights will glow. 4 HOUR DELAY. The 4 Hour Delay light will glow. START/RESUME. NOTE: To cancel the delay, press 4 HOUR DELAY. To immediately start your dishwasher, press START/RESUME. To delay the start (Model KUDS02SR) 1. Open the door. 2. Select a wash cycle and options. The selected cycle and option lights will glow. 3. Press 4 HOUR DELAY. You will see Heat Dry The Heat Dry option in combination with rinse aid will give you excellent drying results. The energy to use Heat Dry costs pennies per cycle. Heat Dry is on when the light is lit on the Heat Dry button. Be sure to load plastic items in the upper rack to avoid damage. You may turn off the Heat Dry option by pressing HEAT DRY so that the light goes off. However, you will have items in your dish load that will not be dry at the end of the cycle. NOTE: The Heat Dry option is used in all cycles except Rinse Only. Control Lock Use control lock to avoid unintended use of your dishwasher. You can also use the control lock feature to avoid unintended cycle or option changes during a cycle. When Control Lock is lit, all buttons are disabled. NOTES: • The dishwasher door can be opened while the controls are locked. • You can turn on the lock while the dishwasher is running. To turn on the lock Press and hold HEAT DRY for 5 seconds. The Control Lock light glows. If you press any pad while your dishwasher is locked, the light flashes 3 times. showing in the display. The 4 Hour Delay light will glow. 4. Close the door firmly. 5. Press START/RESUME. The Start/Resume light will glow. NOTE: To cancel the delay, open the door and press 4 HOUR DELAY. To immediately start your dishwasher, press START/ RESUME. To delay the start (all other models) 1. Open the door. 2. Select a wash cycle and options. The selected cycle and option lights will glow. 3. 4. Press 4 HOUR DELAY. The 4 Hour Delay light will glow. Press START/RESUME. 5. Close the door firmly within 3 seconds of pressing Start/ Resume. NOTE: To cancel the delay, open the door and press 4 HOUR DELAY. To immediately start your dishwasher, press START/ RESUME and close the door firmly within 3 seconds. To turn off the lock Press and hold HEAT DRY for 5 seconds. The Control Lock light turns off. Sanitized If you select the Sani Rinse option, Sanitized light glows when the Sani Rinse cycle is finished. If your dishwasher did not properly sanitize your dishes, the light flashes at the end of the cycle. This can happen if the cycle is interrupted. The light goes off when you open and close the door or press CANCEL. Clean The Clean light glows when a cycle is finished. The light turns off when you open and close the door or press CANCEL. 16 P P SECURITE DU LAVE-VAISSELLE Votre s6curit6 et celle des autres est tr6s importante. Nous donnons de nombreux messages de securite importants dans ce manuel et sur votre appareil menager. Assurez-vous toujours life tous les messages de securite et de vous y conformer. de Ce symbole d'alerte de securite vous signale les dangers potentiels de deces et de blessures graves & vous eta d'autres. Voici le symbole d'alerte de securit& Tousles messages de securite suivront le symbole d'alerte de securit6 et le mot "DANGER" ou "AVERTISSEMENT'. Ces mots signifient : Risque possible de deces ou de blessure grave si vous ne suivez pas immediatement les instructions. Risque possible de deces ou de blessure grave si vous ne suivez pas les instructions. Teus les messages de securite vous diront quel est le danger potentiel et vous disent comment reduire le risque de blessure et ce qui peut se preduire en cas de non-respect des instructions. A/sa_ v_Jc_ va s:,,
Source Exif Data:File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : No Page Count : 32 Page Layout : SinglePage Page Mode : UseNone Producer : Goby Monitor Application version 3, 2, 1, 4 Create Date : Fri Jun 29 03:28:54 2007 Author : Title : Subject :EXIF Metadata provided by EXIF.tools