KJ TECH KJ-3300 Biometrics Fingerprint Reader User Manual Manual
KJ TECH Biometrics Fingerprint Reader Manual
KJ TECH >
Contents
- 1. Manual
- 2. Manual Addendum
Manual
KJ-3300 USER MANUAL KJTech QUICK START Beginning – QUICK START 1 When beginning the ADMIN (access control manager) should NOT be registered. When the ADMIN is not registered access the menu by pressing “ID” ID and “1234 1234.” (After registering the ADMIN the ID “1234” 1234 will not work and only the ADMIN ID will be able to access) NOTE : When accessing the menu, How to access the menu: * When ADMIN is not registered * When ADMIN is registered 1. Turn on the power. 1. Turn on the power. 2. Follow the following steps. 2. Follow the following steps. [A N Y M O D E] 16: 10: 46 [WED] Use ID“1234” to verify. -When ADMIN is registered, 1-1 Press the ‘*’ sign to access the Administrator mode. 1> USER VALIDATE ADMIN ID : 12345678 After entering “1234” 1234 press the ‘#’ sign. press Enter the Admin ID and p the ‘#’ sign. (the above is when the Admin ID is “12345678”) REGIST 1-3 VALIDATE ADMIN 1:FP 2:CARD If shown like the above you have accessed the system menu. 1-5 1-2 VALIDATE ADMIN ID : 1234 Only the ADMIN ID can verify. [ A N Y M O D E ] 16: 10: 46 [WED] Press the ‘*’ sign. 1> USER -When ADMIN is not registered, Decide how the Admin will be verified. For first time registering: - To verify with fingerprint press 1(FP). - To verify with card press 2. REGIST If shown like the above, you have accessed the system menu. 1-4 VALIDATE ADMIN PRESENT USER FP When a red light is on in the fingerprint screen, place the Admin’s fingerprint on the scanner. Do not lift until the light is off. 1> USER REGIST BEGINNING – QUICK START 2 2> USER DELETE - MENU - 3> USER DELETE Menu navigation buttons 4> USER ALLDEL 5> USER COUNT 6> USER VIEW FORWARD BUTTON BACK BUTTON 7> USER FP EDIT 8> USER TEMP ID 9> EVENT VIEW 10> EVENT COUNT EXIT MENU 11> EVENT DELETE END MENU AND RETURN TO BEGINNING 12> DOOR RELAY PROCESS 15> DOOR ALARM 13> DOOR MODE 14> DOOR TIME 14 16> SET COMM ID 17> SET TIME [ A N Y M O D E] 16: 10: 46 [WED] 1> USER REGIST 18> SET CD TYPE 19> SET FG TYPE 20> SET REACCESS 21> SET CD2 FUN 22> SET ALM FUN 23> SET ANTIPASS [ A N Y MODE] 16: 10: 46 [WED] 24> SET FIRE Press the ‘*’ sign. VALIDATE ADMIN ID : 1234 Menu Access After entering the Admin ID press the ‘#’ sign. (If the Admin ID does not exist, press “1234” to access the menu) 25> SET SECRET 35> TCP/IP DHCP 26> SET LIMIT 36>IP ADDRESS 27> SET DAYLIGHT 37> SUBNET MASK 28> VIEW AT-FUNC 38>GATEWAY 29> VIEW AT-DOOR 39> LANGUAGE 30> VIEW AT-MODE 40> SAVE ENROLL 31> VIEW BELL 41> LOAD ENROLL 32> VIEW T-ZONE 42> SAVE SLOG 33>VIEW NO NO-FUN FUN 43> SAVE GLOG 34> S/W VERSION 44> EXIT ADMIN REGISTRATION 10 [ A N Y M O D E] 16: 10: 46 [WED] Press the ‘*’ sign to access the admin menu. VALIDATE ADMIN ID : 1234 After entering “1234” press the ‘#’ sign the enter the menu. When the machine accepts the fingerprint or card correctly the above will be shown. 1> USER REGIST PRESENT USER FP PRIVILEGE 1: ADMIN 2: USER Press ‘1’ (1:Admin 2:User) The above shows when ‘FP’ (fingerprint) is selected. selected When the sensor emits a light place the finger to be used. 12 SETTING COMPLETE Complete 1> USER REGIST FP ID : 1234 Enter fingerprints g p ID.1~4 digits) g ) 11 The above shows when ‘FP’ is selected. -FP 1 : Register 1 fingerprint -FP 2 : Register 2 fingerprints Press the ‘#’ sign to process. Enter an ID number to be used, up to 8 digits and press ess tthe e ‘#’ # ssign. To make sure enter one more time. If its ‘2FP’ enter a different fingerprint 1> USER REGIST 1: 1 FP / 2: 2 FP 1> USER REGIST 1> USER REGIST ID : 12345678 1> USER REGIST PRESENT USER FP 1> USER REGIST -----------OK--------- 1> USER REGIST 1: CD 2: FP 3: CD/FP Decide which will be used for entrance. 1.CD : Card 2.FP : Fingerprint 3.CD/FP : Card and Fingerprint Press the ‘#’ sign after selection. NOTE : - Admin authority is given to a users ID. Therefore, an Admin’s card or fingerprint can be reused to a new user’s ID. CHAPTER 2 - MENU EXPLAINATION- CHAPTER 2 – MENU EXPALINATION - EXPLAINATION OF EACH OPTION SYSTEM MENU 1. USER REGIST 1-1> USER/ADMIN CARD REGISTRATION 1-2> USER/ADMIN FINGERPRINT REGISTRATION 1-3> USER/ADMIN FINGERPRINT AND CARD REGISTRATION SYSTEM MENU 2. 2 USER VERIFY 2> USER/ADMIN VERITY SYSTEM MENU 3. USER DELETE 3> USER/ADMIN DELETE SYSTEM MENU 4. USER ALL DELETE 4> USER/ADMIN ENTIRE DELETE SYSTEM MENU 5. USER COUNT 5> USER/ADMIN REGISTRATION STATUS SYSTEM MENU 6. USER VIEW 6> VIEW REGISTERED USER/ADMIN SYSTEM MENU 7. USER FP EDIT 7> EDIT USER/ADMIN FINGERPRINT SYSTEM MENU 8. USER TEMP ID 8> TEMPORARY USER ID SETUP SYSTEM MENU 9. EVENT VIEW 9> EVENT VIEW SYSTEM MENU 10. EVENT COUNT 10> EVENT COUNT SYSTEM MENU 11. EVENT DELETE 11> EVENT DELETE SYSTEM MENU 12. DOOR RELAY 12> Door Relay SETUP SYSTEM MENU 13. DOOR MODE 13> DOOR MODE SETUP (Card, ID, 지문) SYSTEM MENU 14. DOOR TIME 14> LOCK TIME SETUP SYSTEM MENU 15. DOOR ALARM 15> DOOR OPEN ALARM SETUP SYSTEM MENU 16. 16 SET COMM ID 16> CONTROLLER ADDRESS SETUP SYSTEM MENU 17. SET TIME 17> CONTROLLER TIME SETUP SYSTEM MENU 18. SET CD TYPE 18> CARD OPERATION MODE SETUP 10 11 12 13 14 15 15 16 17 18 19 19 20 20 22 22 23 24 25 SYSTEM MENU 19. SET FG TYPE 19> FINGERPRINT SECURITY LEVEL SYSTEM MENU 20. SET REACCESS 20> SECURITY RECOGNITION SETUP SYSTEM MENU 21. SET CD2 FUN 21> EXTERNAL READER FUNCTION KEY SETUP SYSTEM MENU 22. SET ALM FUN 22> EXTERNAL ALARM FUNCTION SETUP SYSTEM MENU 23. SET ANTIPASS 23> ANTI-PASS BACK SETUP SYSTEM MENU 24. SET FIRE 24> FIRE-SENSOR SETUP SYSTEM MENU 25. SET SECRET 25> ID SECURITY (“*” SIGN) SETUP SYSTEM MENU 26. SET LIMIT 26> SET PROHIBIT TIME SYSTEM MENU 27. SET DAYLIGHT 27> SETUP CONTROLLER TIME ZONES SYSTEM MENU 28. VIEW AT-FUNC 28> VIEW FUNCTION KEY SYSTEM MENU 29. VIEW AT-DOOR 29> VIEW ALLOWED AUTO DOOR TIME SYSTEM MENU 30. 30 VIEW AT-MODE AT MODE 30> VIEW TIME ZONE OPERATION MODES SYSTEM MENU 31. VIEW BELL 31> VIEW BELL TIME ZONE SYSTEM MENU 32. VIEW T-ZONE 32> VIEW SET TIME ZONE SYSTEM MENU 33. VIEW NO-FUN 33> RELAY NO FUNCTION KEY VIEW SYSTEM MENU 34. S/W VERSION 34> VIEW CONTROLLER VERSION SYSTEMMENU 35,36,37,38 TCP/IP MENU SYSTEMMENU 39. 39 LANGUAGE 39>CONTROLLER LANGUAGE SELECTION SYSTEMMENU 40,41,42,43 USB MEMORY MENU SYSTEM MENU 44. EXIT 44> EXIT MENU (TO INITIAL SCREEN) 26 27 27 28 29 29 30 30 31 32 32 33 33 34 34 35 36 37 38 39 1. SYSTEM MENU ACCESS NOTE : (AFTER ADMIN IS REGISTERED) -Only Only when the admin is registered registered. (refer to pg13 for instructions) 1-1 -When the admin ID is incorrect, access to the menu is denied and the screen will return to t the th initial i iti l screen. [ANY MODE] 16: 10: 46 [WED] The screen above shows the initial screen. Press the ‘*’ sign. -If the admin is not registered, access to the menu is allowed. It is a good idea to register at least one admin. 1-2 VALIDATE ADMIN ID : 12345678 Enter the admin ID and press the ‘#’ # sign. (the above shows when the admin ID is ‘12345678’.) 1-3 VALIDATE ADMIN 1:FP 2:CARD Select what to use when registering for admin. 1: Fingerprint g p 2:Card 1-4 VALIDATE ADMIN PRESENT USER FP Use fingerprint used to register admin ID. Access to the system menu. Press F1 and F2 to access a menu. 1-4 VALIDATE ADMIN PRESENT USER CD Use card used to register admin ID. 1-5 1. USER REGIST 1> USER REGIST 1> USER REGIST NOTE : •From the Press the ‘#’ sign in the 1> menu. 3 step 1: CD – Register user ID by card 2: FP – Register user ID by fingerprint 1> USER REGIST ID : 12345678 3: C+F – Register user ID by card and fingerprint WARNING: Setup the Card Type and Facility Code in the #18 system menu before manually inputting card numbers into the system. Enter the user ID number that is to be used for entry and press the ‘#’ sign. 1> USER REGIST 1: CD 2: FP 3: C+F Press the ‘1’ button. Manually enter the card’s card s number. 1: Enter the card number for entry entry. 2: Place card onto reader for entry. Place card onto the reader. The reader will automatically register onto the system. 1: Admin 2: User 4-2 4-1 2: AUTO CD ENTRY PRIVILEGE 1: ADMIN 2: USER 1: MAN CD ENTRY NUM :12345678 1: MAN CD ENTRY 2: AUTO CD ENTRY 4-B 4-A PRIVILEGE 1: ADMIN 2: USER 1: Admin 2: User SETTING COMPLETED User card registration is complete. 1-2>USER REGIST NOTE : 1> USER REGIST Press the ‘#’ in the 1> menu. 1> USER REGIST ID : 12345678 -Using U i ttwo fi fingerprints i t (2FP) iinstead t d of one (1FP) makes it more easy for the system to recognize users. -One fingerprint is placed on the sensor three times to complete registration. 4-C Enter the user ID used for entry and press the ‘#’ sign. 1> USER REGIST 1: CD 2: FP 3: C+F 1> USER REGIST PRESENT USER FP When the red sensor light appears place the same finger on the sensor. PRIVILEIGE 1: ADMIN 2: USER 1: ADMIN – Setup as Admin 2: USER – To setup as user press ‘2’ 1> USER REGIST ---------OK----------- 1> USER REGIST FP ID : 1234 When correctly done, the above is shown 4-A 1> USER REGIST PRESENT USER FP Enter the fingerprint ID (1 ~ 4 digits) When the red sensor light appears place the finger to be used for entry on the sensor. 1> USER REGIST 1:1FP / 2: 2FP 10 User fingerprint registration complete 4-B Press ‘2’. 1:1FP – Register one fingerprint 2:2FP – Register two fingerprints SETTING COMPLETED 4-1 1> ENROLL USER PRESENT USER FP 4-3 1> USER REGIST PRESENT USER FP When the red sensor light appears, place a different fingerprint. 4-2 1> ENROLL USER ---------OK----------When correctly done, the above is shown. 1-3>USER REGIST NOTE : -When When registering a fingerprint fingerprint, please refer to ‘how to use your fingerprint’ chapter. 1> USER REGIST Press the ‘#’ sign at 1> 7-1 1> USER REGIST PRESENT USER FP 1> USER REGIST ID : 12345678 Enter the user ID that is used for entry 1> USER REGIST ---------OK----------- When the light from the sensor turns on you may place your fingerprint used for entry 1> USER REGIST 1:1FP / 2: 2FP 1> USER REGIST FP ID : 1234 11 1: Enter the number found in the back of the card or… 2: Place card at the reader PRIVILEGE 1: ADMIN 2: USER g p Enter fingerprint ID (up to 4 digits) 1: ADMIN – Set as admin p press ‘1’ or… 2: USER – Set as user press ‘2’ 5-1 1: MAN CD ENTRY 2: AUTO CD ENTRY When the sensor light is on place the same fingerprint on the sensor. 1> USER REGIST FP ID : 1234 Enter a fingerprint ID. (1 ~ 4 digits) 7-3 1> USER REGIST PRESENT USER FP 1:1FP – Register one fingerprint 2:2FP – Register two fingerprints Press ‘3’ When d Wh done properly l th the above will be shown 1> USER REGIST 1: CD 2: FP 3: C+F 7-2 2: AUTO CD ENTRY Place card used for entry on the reader. SETTING COMPLETED Fingerprint registration complete 2> USER VERIFY Use Fingerprint and Card to verify registered USER/ADMIN ID ID. NOTE : -When checking fingerprints refer to the ‘How to use your fingerprint’ 2> USER VERIFY -The below menu 2 : FINGER applies to the KF-2000 and FPC-301 only. Press the “#”at the 2> menu. 2> USER VERIFY ID : 12345678 A 2> USER VERIFY 1: FINGER 2: CARD Card or fingerprint ID To verify using fingerprint press ‘1’ To verify using card press ‘2’ 2-1 2-2 2> USER VERIFY PRESENT USER CD 2> USER VERIFY PRESENT USER FP When the sensor light is on place the same fingerprint on the scanner 2>USER VERIFY ID : 12345678 A Example: ID is 12345678 and status is Admin. (A: Admin U: User) 12 Place card on the reader. A : Admin U : User 3> USER DELETE When deleting registered user/admin ID, that ID will no longer have authorization 3> USER DELETE Press the ‘#’ sign at 3> NOTE : 3> USER DELETE ID : 12345678 Enter the ID that you wish to delete. (up to 8 digits) Press the ‘#’ sign. - When deleting an ID, all fingerprint ID and card information connected with the ID will be deleted. - When deleting an ID all events that happened before deletion will NOT be deleted. 3> USER DELETE 1: DEL 2:CANCEL 1:DEL – delete 2:CANCEL- cancel delete 3> USER DELETE PLEASE WAIT Processing ID delete… 13 3> USER DELETE Delete complete 4> USER DELETE (delete all users) 4> USER DELETE NOTE : - When deleting all users, the admin will also be deleted. Press the ‘#’ sign at 4> 4> USER DELETE 1: YES 2: CANCEL Press “1” SETTING COMPLETED All user delete processing 4> USER DELETE All user delete complete 14 5> USER COUNT (registered user/admin status view) You can view the number of card or fingerprint ID’s registered to the controller. NOTE : 5> USER COUNT - Total number of users include the admin. Press the ‘#’ # at 5> 5>. USER : 00123 FINGER: 00099 User (including admin) currently registered is 123. Fingerprint user amount is 99. 6> USER VIEW (view user/admin registered info.) View user/admin registered info currently registered on the controller. 6> USER VIEW List navigation buttons User/Admin ID Order User(U)/Admin(A) Back Press the ‘#’ sign at 6> Forward 0001 12345678 A FP: 0001 TZ:01,02 Order :0001 User ID : 12345678A (Admin) Fingerprint ID : 0001 Time zone : 01, 02 time zone 15 0001 12345678 A FP:0001 TZ:01,02 Exit Fingerprint(FP)/Card (CD) ID Timezone 1,2 setup 7> USER FP EDIT (Change user/admin fingerprint) Used to change user/admin fingerprint. This will not change the user/admin ID. 7> USER FP EDIT 7> USER FP EDIT PRESENT YOUR FP Press the ‘#’ sign at 7> 7> USER FP EDIT ID : 12345678 7> USER FP EDIT --------OK------------ Enter the user ID that you wish to change and press the ‘#’ sign Fingerprint input complete 7> OPER.. MODE 1 : YES 2: CANCEL 7> USER FP EDIT PRESENT YOUR FP Select ‘1’ Place your fingerprint again for verification 7> USER FP EDIT 1: 1FP / 2: 2FP 1FP: Change one fingerprint 2FP: Change two fingerprints 16 - Refer to the ‘how to use your fingerprint’secton. Place the fingerprint to replace the old SETTING COMPLETED Fingerprint input complete NOTE : 8> USER TEMPORARY ID When a temporary user needs to enter, but doesn’t need to register (Ex. visitor, guest) 8> USER TEMP ID SETTING COMPLETED Press the ‘#’ sign at 8> NOTE : - Cannot register temporary ID as admin. Temporary ID complete 8> USER TEMP ID ID : 12345678 Enter a temporary ID number (up to 8 digits) and press the “#” sign. 8> USER TEMP ID TIME [1 - 9] : 3 Enter the amount the temporary user is allowed to enter and press the “#” sign. (minimum 1, maximum 9) - Cannot register temporary ID with fingerprint. -When properly registered the following is shown: WELCOME [F0 [F0-0] 0] ID: 12345678 T (T : Temporary) -The admin can set the amount of entries of a temporary ID.(1-9) -When the amount of entries are used, the Admin is able to add more entries allowed for the temporary y ID. -Events are recorded the same way as regular user ID. -Cannot Cannot register temporary ID from regular user ID. 17 9> EVENT VIEW View user ID time of entry, date, access authorization, system authorization. 9> EVENT VIEW NOTE : Press ‘#’ at the screen above. 1. SLOG 2. GLOG 1. SLOG : Access Event 2. GLOG: Exit Event 0001 : 09/06 15:09 MASTER MENU IN EVENT OVERVIEW - MASTER MENU IN : Access Admin menu it Ad i menu - MENU MODE EXIT : E Exit Admin - MASTER MENU FAIL : Admin menu Access failed - 12345678 [GRANTED] : ID/fingerprint 12345678 entry - 12345678 [DENIED] : ID 12345678 Access failed - USER FG REG : Register user fingerprint g p - USER CD REG : Register user Card - FINGER DOWNLOAD : Download fingerprint - CARD DOWNLOAD : Download card - NONE : No event The example above shows that the admin accessed the admin menu at 9/6 at 15:09. 9> EVENT VIEW 0002 : [NONE] To exit press ‘*’ when the screen above appears. (The example above shows no event.) 18 MENU NAVIGATION BUTTONS NEXT EVENT BACK EVENT EXIT 10> EVENT COUNT 10> EVENT COUNT Pres ‘#’ # when the above appears. appears 10> EVENT COUNT 00012/00012 In this screen the user may know the quantity of events. 11> EVENT DELETE NOTE : 11> EVENT DELETE -All events will be deleted. Press ‘#’ when the above appears. 11> EVENT DELETE 1: YES 2: CANCEL SETTING COMPLETED Event delete complete. 19 12> DOOR RELAY This menu is for changing the functions of Relay 1 and 2. Normally Relay 1 controls the door. In cases where Relay 1 cannot be used, the user can change and use Relay 2 to control the door. 12> DOOR RELAY Press the ‘#’ sign at 12> 12> DOOR RELAY 1 : RLY 2 : RLY [1] SETTING COMPLETED When Relay 1 is controlling “Door Control” To change to Relay 2, Press “2” Relay setup complete 13> DOOR MODE In this menu the user is allowed to setup door modes according to certain situations. There are a total of 15 ways. This page only shows how to setup. 13> DOOR MODE 13 List navigation menu NOTE : forward Press the ‘#’ sign at 13> 13> DOOR MODE [ ID or FP ] 20 back setup exit - When accessing the menu, the current mode used will be shown. Press “F1” to change to a different mode and press the ”#” # sign 13-1> DOOR MODE (detailed auto door mode instructions) [Open] : Always Open (Fail-Safe Mode) [Close] : Always Closed (Fail-Secure Mode) – no access with any form of authorization [FINGER] : Fingerprint Only – no access with ID or card NOTE : [CD] : Card Only – no access with ID or fingerprint -For fingerprint disabled personnel, any mode of ID entrance is allowed, except for [CLOSE] mode. [ID or FP] : ID or Fingerprint Only – no access with card [ID or CD] : ID or Card Only – no access with fingerprint [[CD or FP]: ] Card or Fingerprint g p Only y – no access with ID [Any Mode]: Any Form of Authorization - access granted with any form of authorization [ID and FP]: Both ID and Fingerprint Required for Access – must punch in ID before fingerprint authentication [ID and CD]: Both ID and Card Required for Access – must punch in ID before Card authentication [CD and FP]: Both Card and Fingerprint Required for Access – card must be authorized before fingerprint authentication [ID&FP]or[CD&FP] : both ID and Fingerprint or both Card and Fingerprint are required for Access [ID&FP]or[CD] : both ID and Fingerprint or just Card are required for Access [ID&FP]or[ID&CD] : both ID and Fingerprint or both ID and Card are required for Access [ID & CD & FP]: all three forms needed for access NOTE : The operation mode described graphic above is shown in the g on the right located in the dotted square 21 [ CD ] 16: 10: 46 [WED] 14> DOOR TIME This menu is for setting the time when the lock device locks again after unlocking. NOTE : 14> DOOR TIME -The default door time is 3 seconds. Press the ‘#’ # sign when the above appears. 14> DOOR TIME 03 TIME TIME= 05 sec SETTING COMPLETED Locking time setup complete Able to setup a maximum of 99 seconds. Aft input After t press the th “#”sign. “#” i 15> DOOR ALARM (DOOR open ring) This menu if to setup an alarm (ring) when a user fails to close the door after entry or exit. When this happens the alarm will be activated after a user set time (1-99 seconds). The alarm will deactivate after the door closes properly. 15> DOOR ALARM At the screen above, press the ‘#’ sign. 15> DOOR ALARM 03 TIME= 05 sec 15> DOOR ALARM 1 : SETUP 2 : NO 22 To setup press “1” If you do not want this option press “2” Delay time can be setup up to 99 seconds. Press The “#” sign after completion. SETTING COMPLETED Door Alarm complete. 16> SET COMM ID (controller address setup) When networking several controllers to a computer, each controller needs its own unique address. This menu is to designate controllers a unique address or edit/change an existing address. (users are recommended to seek advice) 16> SET COMM ID Press ‘#’ when the above is shown. 16> SET COMM ID [01] 1-16 = 02 Choose between 1~16 that will be the address and press “#”. SETTING COMPLETED Address setup complete Users must designate an address to each product that is connected. If the S/W is installed to the computer, it can be done from there. - SF-3000 can each have address from 1-16 - The factory default setting is ‘1’. For more details refer to the ‘installers instruction manual’ 23 17> SET TIME (controller time setup) The internal clock is used to save the time setup for an event. The internal clock must be exact. 17> SET TIME NOTE : Sunday – 1 Monday – 2 Tuesday –3 Wednesday – 4 Thursday - 5 Friday – 6 Saturday - 7 Press the ‘#’ sign when the above is shown. YEAR:MON:DAY 05 : 09: 11 Enter by order year, month, date and skip by pressing the ‘#’ sign. HOUR:MIN:SEC 10 : 11: 26 First input the hour, minute and d second d and d press th the ‘#’ sign 24 S MT W T F S 1 2 3 4 5 6 7 Select the day by pressing the number that corresponds to the day SETTING COMPLETED Time setup p complete 18> SET CD TYPE (Wiegand type setup) This menu provides information on how to setup cards used for entry. This chapter will teach you how to register your card and change your card type type. 18> SET CD TYPE Press ‘#’ at 18> 18> SET CD TYPE 18 1:26 2:34 3:37 1:26 – 26bit wiegand card (HID, EM, INDALA) 2:34 – 34bit wiegand card (MIFARE) 3:37 – 37bit wiegand card (KEICO) 25 FACILITY CODE 0-255 : Enter a secure code with the number buttons from ‘0’ to ‘255’ SETTING COMPLETED SETTING COMPLETED Card type setup complete’ complete Card type setup complete 19> BRIGHT ADJ (fingerprint sensor brightness setup) 19> BRIGHT ADJ Press ‘#’ when the above menu is shown 19> SET FG TYPE 1 : LEVEL 2 : AUTO Adjusting the brightness SETTING COMPLETED Fingerprint sensor brightness setup complete 26 20> SET REACCESS (authorization security setup) This function was created to decrease the troublesome situations of using a card again after a fingerprint is read as an error when a fingerprint scan is required after a card scan scan. NOTE : 20> SET REACCESS - If an admin is registered by a fingerprint, authorization security is not in effect when accessing the system menu. Press the ‘#’ sign at 20> 20> SET REACCESS [ 3 ] 0-9 : 5 SETTING COMPLETED Enter the amount of times a re-scans allowed. Press the “#” sign after setup. (maximum : 10) Authorization security setup complete 21> SET CD2 FUN (external reader function key) If a controller is connected to a reader, this function gives a function key to the external reader automatically, thus a an automatically setup function key is given to a user who is authorized from an external reader. Events of user entries from the reader are stored. (Ex. For time & attendance) 21> SET CD2 FUN Press th the ‘#’ sign i att 21 21> 27 21> SET CD2 FUN [F1-0] FUN= F2-1 Select a key y you y wish to setup as a function key from F1 through F4 and enter a number (0-9) SETTING COMPLETED External l reader d ffunction ti kkey setup complete 22> SET ALM FUN (external alarm function setup) When opening a door and entering, an alarm will activate after pressing a set function key and inputting a card, fingerprint or ID number. This will be effective to alert security guards or law enforcement when an intruder forces a user to access a door. NOTE : 22> SET ALM FUN Press th the ‘#’ sign i att 22 22> To activate an alarm to indicate an intrusion intrusion, press the function key at the corresponding user/admin page from the machine and input an ID, fingerprint or card. Screen 2 explanation 1: RELAY – activates an external alarm. 2 BUZZER – an internal 2: i t l buzzer from the th machine hi is i activated. ti t d - Users may setup a function key to a RELAY or BUZZER 22> SET ALM FUN 1:RELAY 2:BUZZER Button 1 : External alarm setup Button 2 : Internal buzzer setup 22> SET ALM FUN [Relay] FUN= F1-2 Press a function key from F1 through F4, then press a button 0 through 9 and press the “#” sign 28 22> SET ALM FUN [Buzz] FUN= F0-0 Press a function key from F1 through F4, then press a button 0 through 9 and press the “#” sign SETTING COMPLETED Alarm setup complete 23> SET ANTIPASS (Anti-Pass Back) When a controller is located at an entrance and exit, a user must have permission to exit. (Ex Parking lot management (Ex. management, office security etc) 23> SET ANTIPASS 23> SET ANTIPASS 1:YES 2:NO [1] SETTING COMPLETED Button 1 : Anti-pass back setup Button 2 : Anti-pass back disable [1] : ‘1’ for anti-pass back setup [2] : ‘2’ for anti-pass back disable Press the ‘#’ sign at 23> Anti-Pass setup complete 24> SET FIRE (fire/intrusion detect setup) This function is connected to a fire alert system. An alert signal is activated when there is a fire or intrusion. NOTE : -This function is connected to a fire alert system. An alert signal is activated when there is a fire or intrusion and all doors are forced open -Intrusion detect closes all doors when an intrusion is detected. 24> FIRE-SENSOR Press the ‘#’ sign at 24> 24> FIRE-SENSOR 1:YES 2:NO [1] Button 1 : fire detect setup (intrusion detect disable)) Button 2 : fire detect disable (intrusion setup) [1] : ‘1’ for fire detect setup [2] : ‘2’ for intrusion setup 29 SETTING COMPLETED Fire/intrusion detect setup complete. 25> SET SECRET (ID security) For added security, ID shown in the LED screen will show as “********” when receiving authorization for entry. NOTE : 25> SET SECRET -Regardless of the digits of the ID off a user/admin, / d i the th following f ll i is shown “********” Press the ‘#’ sign at 25> 25> SET SECRET 1:ON 2:OFF [1] SETTING COMPLETED Button 1 : ID security setup Button 2 : ID security deactivate ID security setup complete 26> SET LIMIT In this menu authorization is given once every set times (units of 10 minutes). 26> SET LIMIT 26> SET LIMIT [MIN]<0-600>] [MIN] 0 600 ] : 010 Press the ‘#’ at 26> Time is set in units of 1 minute. The above shows “10” therefore is 10 minutes minutes. If a user is authorized at AM10:00, the user is unauthorized until AM10:10 30 SETTING COMPLETED Entry limit setup complete 27> SET DAYLIGHT This function is used to change or recover the time at a certain period in the controller. (Ex-Summer (Ex Summer Time) NOTE : 27> SET DAYLIGHT SETTING COMPLETED Press the ‘#’ # sign at 27> Y M D 1. 05 : 09 : 11 Y M D 4. 05 :09 : 12 H M 09 :00 Press the ‘#’ after setting up the changed times H M 19 : 00 Press the ‘#’ sign after setting up new time of recovery Y M D 2. 05 : 10 : 11 H M 10 :00 Press the ‘#’ sign after setting up the time that is changed from the daylight savings 31 Change the time back to 2005 September 15th at 2005 October 15th 14:00. S t complete. l t Setup Ex.) Change g the time to October 11th 10:00 at September 11th 9:00. Y M D H M 3. 05 : 10 :15 14 : 00 Press the ‘#’ sign after setting up the time of recovery. Warning : The setup of this menu can be set up in the program as well. When setting up from a controller that is connected to a computer, the computer’s time will interfere. Therefore, the time should be set offline. For communication purposes, setup from the program. (For instructions on how to set up from the program, please refer to the program manual) 28> VIEW AT-FUNC (View setup function key) This function automatically saves the function key to the event without pressing any function keys only within a set time zone This function is usually used to save users from pressing the function key to sign in and out of work all the time zone. time. In this menu you only have to assign a function key to a set time zone from the program. (See the program manual for edit and setup methods) List navigation button Next Button [ 01 ] DAY : ALL 28> VIEW AT-FUNC 13:00 18:00 F4-9 Back Button The above shows: All days from 13:00 to 18:00 “F4-9” function key is automatic set so users do not have to press the function key. Press the ‘#’ # sign when the above is shown. E it M Exit Menu 29> VIEW AT AT-DOOR DOOR ((view sett auto t d door ti time zones)) In this menu times are recorded when an automatic door setup at the program is activated. This menu is used only to view set times for automatic doors. (for editing and setup procedures please refer to the program manual.) 29> VIEW AT AT-DOOR DOOR Press the ‘#’ sign at 29> 32 [ 01 ] DAY : ALL 13:00 - 18:00 Ex) the automatic doors are in operation from 13:00 to 18:00 everyday List navigation button forward back exit 30> VIEW AT-MODE (view time management setup) This function is used for changing activation modes at set times. This is different from the switching modes in menu 13. In this function operation modes are changed automatically function, automatically. Only the operation mode’s mode s set times are shown shown. (for editing and detailed information, please refer to the program manual) 30> VIEW AT-MODE [ 01 ] DAY : fri 11:00 14:00 [FP] Back Ex) from Friday 11:00 to 14:00 operation mode is “FINGER” Press ‘#’ at 30> List navigation buttons Forward Exit 31> VIEW BELL In this function, a bell is rung at set times automatically. This is usually used for school classroom bells or alarms. Users are only able to view set bell time zones. (for editing and detailed information please refer to the program manual.) 31> VIEW BELL Press ‘#’ at 31> 33 [ 01 ] DAY : fri 11:00 T=005 Ex) at Friday 11:00 a bell is rung for 5 seconds. seconds List navigation buttons forward back exit 32> VIEW T-ZONE The user is able to see saved Timezone Index. This menu is only able to view timezones that are setup. (for editing and detailed explanation please refer to the program manual.) 32> VIEW T T-ZONE ZONE 32> VIEW T T-ZONE ZONE INDEX: 001 [Y] Press the ‘#’ sign at 32> List navigation button Forward Back Exit View the setup timezone. (Up to 254 functions) 33> VIEW NO-FUN NO FUN (View function keys with no functions) This menu shows events saved when verification is denied and a door does not open. Users may only view function keys set up in the menu menu. (for editing and detailed information please refer to the program manual manual. 33> VIEW NO-FUN Press ‘#’ at 33> 34 [F1 1] [F1-1] [F3-1] [F2 [F2-1] 1] [F4-1] Function key is setup as “F1-1” “F21” “F3-1” “F4-1” 34> S/W VERSION VIEW View the current controllers Firm Ware Version NOTE: 34> S/W VERSION 34> S/W VERSION VER : 3.00 Press the ‘#’ sign at 34>. 35> TCP/IP DHCP Exiting the menu. 35> TCP/IP DHCP Press the ‘#’ sign. 35 35>TCP/IP DHCP 1. ON 2.OFF [2] TCP/IP DHCP On/Off verification -The current F/W version is 3.00 and future F/W will be updated. 36> IP ADDRESS (VIEW IP ADDRESS) View the current controller’s IP ADDRESS NOTE: 36> IP ADDRESS 36> IP ADDRESS 192.168..001.224 -The current IP ADDRESS is display. You can change this Ip address as you want. Press the ‘#’ sign at 36>. 37> SUBNET MASK View the current controller’s SUBNET MASK. NOTE: 37> SUBNET MASK Press the ‘#’ sign. 36 37>SUBNET MASK 255.255.255.0 -The current Subnet Mask address is set to 255.255.255.0. This menu is only l ffor viewing i i th the address. dd Address setting is done from the terminal or the S/W. 36> GATEWAY View the current controller’s IP ADDRESS NOTE: 38> GATEWAY 38> GATEWAY 192.168..001.001 Press the ‘#’ sign at 38>. -The current GATEWAY is set to 192.168.001.001. This menu is only for viewing the address. Address setting is done from the terminal or the S/W. 39> LANGUAGE View the current controller’s LANGUAGE OPTION. NOTE: 39> LANGUAGE 39>LANGUAGE 1. KR 2. EN 3. CH -1. KR (KOREAN) -2. EN (ENGLISH) -3. 3 CH (CHINESE) Press the ‘#’ sign. 37 40> SAVE ENROLL Saving currently registered users to the USB Memory NOTE: 40> SAVE ENROLL 40> SAVE ENROLL 1. YES 2. NO - Only USB2.0(FAT, O l USB2 0(FAT FAT32 format) can be used. Press the ‘#’ sign at 40>. 41> LOAD ENROLL Uploading registered users to the controller from the USB Memory. 41> LOAD ENROLL Press the ‘#’ sign. 38 -This menu displays how to save registered users to the USB memory stick. 41>LOAD ENROLL 1.YES 2. NO 42> SAVE SLOG Saving ALL EVENTS from the controller to the USB Memory. 42> SAVE SLOG 36> SAVE SLOG 1. YES 2. NO Press the ‘#’ sign at 42>. 43> SAVE GLOG Saving Time & Attendance EVENTS from the controller to the USB Memory. 43> SAVE GLOG Press the ‘#’ sign. 39 43>SAVE GLOG 1. YES 2. NO 44> EXIT (EXITING THE MENU) Closing the menu NOTE: 44> EXIT [CD] 12:56:32 [THU] Press the ‘#’ sign at 44>. To initial screen 40 -Press ‘F4’ to exit menu at anytime. CHAPTER 3 - OTHERS - 41 How to use the function key The Function Key is usually used in for time & attendance. The admin is able to setup a certain value to a function key in the program (F1 = sign in) The admin is then able to find out the sign in status. ACTIVATING FUNCTION KEY THROUGH FINGERPRINT INPUT [ANY MODE] 16 10 16: 10: 46 [THU] 1. PRESS A NUMBER KEY AFTER PRESSING A FUNCTION KEY. Press a function key (F1~F4) only or, press a number key after pressing a function key. ACTIVATING FUNCTION KEY THROUGH ID INPUT [ANY MODE] 16 10 16: 10: 46 [THU] ACTIVATING FUNCTION KEY THROUGH CARD INPUT [ANY MODE] 16 10 16: 10: 46 [THU] 1. Press a function key (F1~F4) at the initial screen or press a function key after pressing a number key. 1. Press a function key (F1~F4) at the initial screen or press a function key after pressing a number key. 2. Enter the ID number used for entry. 2. Enter the ID number used for entry. 2. INPUT A FINGERPRINT USED FOR ENTRY. NOTE : The function key should be used with the time & attendance program. Only enter a function for the time & attendance and onlyy saves data of entries. 42
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.7 Linearized : Yes Author : BongOk Create Date : 2012:10:16 10:42:07+09:00 Modify Date : 2012:10:16 17:21:12+09:00 XMP Toolkit : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04 Creator Tool : PScript5.dll Version 5.2.2 Metadata Date : 2012:10:16 17:21:12+09:00 Producer : Acrobat Distiller 9.5.2 (Windows) Format : application/pdf Title : Microsoft PowerPoint - [English]KJ-3300_UserManual.ppt [호환 모드] Creator : BongOk Document ID : uuid:7be1d242-84bd-45a1-8d43-79923a2ccfc9 Instance ID : uuid:9b546dac-5d78-44a1-810f-c5af7071aae4 Page Count : 42EXIF Metadata provided by EXIF.tools