KMTEL SP-100T Smart Pointer- Transmitter User Manual QMTSP 100T manual
KMTEL Co., Ltd. Smart Pointer- Transmitter QMTSP 100T manual
KMTEL >
User Manual
The Smart Pointer guarantees
the easiest and most effective way
to a better presentation
General Description
To make it your presentation better, the Smart Pointer integrates the functions of a
page up/down and a laser pointer. The Smart Pointer’s compact and complete design
gives you the easy control of presentation slide up/down and mobility needed to
concentrate on your presentation at a range of over 20m. Any software and PC
programming is not required and a few second is taken for installation to use.
Key Features
Terms and Explanations
Laser Button
Up Button
Down Button
Laser Hole
ClipLock/Unlock
Switch
USB connector
LED Indicator
Laser Button (R) : Laser on/off control
Up Button (5): Slide up control
Down Button (6): Slide down control
Lock/Unlock Switch : To change battery
Clip : To fix the transmitter to the bag or cloth
LED Indicator
Blinking : Connected and waiting for ID
Off : ID received and waiting for CMD
Off-On-Off : Everytime CMD received
Transmitter
Battery
Cover
♦Plug and play function
-No PC programming and S/W
♦Working on any computer
-On any computer using a USB port
♦Remote control range within 15m with a very low power
–Eliminates LOS problems encountered with IR systems
♦Transmitter identification
-Use thousands of ID number to avoid multi-user interferences
Receiver
Installation and Usage
Desktop or Notebook PC
USB port
1
2
When you plug a receiver into a USB port, you will see LED indicator
is blinking.
Push a either down (6) or up (5) button in the transmitter to implant user ID.
When ID is set, LED goes to command waiting state.
3Begin your presentation.
1 2
3 4
5
For Only WIN98 Users
Radio Frequency
Battery Alkaline, 12V/23A USB Bus-powered
315 MHz (USA, Asia), 433.92 MHz (Europe)
Enclosure Molded plastic (violet, silver, gray, ordered colors)
Dimension 115mm(L) ×18mm(H) ×19mm(W) 65mm(L) ×7mm(H) ×20mm(W)
Weight 20 grams (w/o battery) 10 grams
Laser Pointer with Mouse
Control (Transmitter)
Laser Module
Interface
Wavelength: 670nm (Class IIIa)
Output Power: 2.5±0.5mW
Wireless Mouse Control
Interface (Receiver)
Technical Specifications
USB HID Spec., Ver.1.1
Operating Current 40mA (LM), 15 mA (RF) 10 ~ 12 mA
Battery Change
1
2
3Push battery cover
Unlock switch
Rotate clip
Supported OS Win98/SE/Me/2000/XP,
Mac, Linux, WinCE
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection
against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and,
if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio or
television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to
try to correct the interference by one or more of the following measure:
-Reorient or relocated the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-Consult the dealer or an experienced radio/TV technician for help.
-Shielded cables must be used to comply with FCC regulations.
WARNING
Changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.