KONICA MINOLTA A09N2 Authentication Unit User Manual Installation manual

Download:
Mirror Download [FCC.gov]
Document ID	2525678
Application ID	M791RGGcrjnBkI4IL87VRg==
Document Description	User Manual_Installation manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	79.93kB (999171 bits)
Date Submitted	2015-02-06 00:00:00
Date Available	2015-02-06 00:00:00
Creation Date	2015-01-09 15:14:11
Producing Software	Acrobat Distiller 7.0 (Windows)
Document Lastmod	2015-01-09 15:14:30
Document Title	User Manual_Installation manual
Document Creator	PScript5.dll Version 5.2.2

AU-201S Authentication Unit
INSTALLATION MANUAL
Applied Machines: 367/287/227
MFP: 36 ppm/28 ppm/22 ppm
Product Code: A789/A7AH/A7AK
1. Accessory parts
No.
Name
Shape
Note:
• The following items are required to install this
product.
• Local Interface Kit EK-608
• Working Table WT-506
• When you attach this Authentication unit AU201S to the Working Table, we recommend you
attach this unit to the Working Table before you
attach the Working Table to the machine.
• When you use the Mount Kit to attach this
Authentication unit to the machine, see the
installation manual of Mount Kit for information
on the installation procedure.
• This manual provides the illustrations of the
accessory parts and machine that may be
slightly different in shape from yours. In that
case, instead of the illustrations, use the
appearance of your machine to follow the
installation procedure. This does not cause any
significant change or problem with the procedure.
Q’ty
1. Authentication
unit
2. Ferrite core
3. Hook-and-loop
fastener A
(hook)
(25.4 x 10 mm)*
4. Hook-and-loop
fastener B
(loop)
(25.4 x 10 mm)*
5. Safety
information
guide
6. Additional
information
set
set
This part is not used in this installation.
Keep this bag away from babies and
children. Do not use in cribs, beds,
carriages, or playpens.
The thin film may cling to nose and
mouth and prevent breathing. This bag is
not a toy.
E-1
A7AH-9622-00
2. Installation procedures

Remove the cover from the main body as shown
in the illustration. (Two screws)
(1) Turn OFF the power switch and unplug the
power cord from the power outlet.
(2) Attach the ferrite core as shown in the illustration.
Note:
• Place the ferrite core such that the cable is
wound twice around the ferrite core.
• Place the ferrite core approximately 60 mm
away from the authentication unit.
(4) Open the front door of the main body.
(5) Remove the three screws, release the six tabs,
and remove the control panel assembly.
Note:
Do not use too much force when removing as the
cable is connected.
(3)

Remove the two screws and remove the cover
on the back side of the keypad. Disconnect the
connector and remove the keypad.
E-2

Disconnect the connector and remove the local
interface board unit. (Three screws)
(6) Remove the cable from the control panel assembly.
(7)

a) Remove the bracket shown in the illustration.
(Two screws)
Note:
Discard one of the two removed screws.
(8) Remove the control panel left cover. (One screw)
(9) Remove the plate spring. (One screw)
b) Remove the bracket from the USB cable.
(Two screws)
Note:
Discard the removed bracket and screws.
E-3
(14)Paste the cushion to the cover, aligning the
cushion with the line marked inside the cover.
Note:
The cushion is supplied with the Working Table.
(10) Open the right door of the main body.
Line
(11) Remove the control panel lower cover.
(Three screws)
(15)Position the authentication unit, aligning its four
corners with the four marks indicated on the
underside of the working table.
(12)

Refer to the installation manual for the Working
Table WT-506 and install the working table.
Mark
(16) Secure the authentication unit cable to the
working table plate with the cable tie.
Note:
• The cable tie is supplied with the Working
Table.
• Cut the excess portion of the cable tie.
(13) Remove the cover from the working table.
(Three screws)
Note:
The cushion, cable tie, and authentication label
are contained inside the cover.
Cable tie
E-4
A09NIXC020DA
(17) Route the cable through the wire saddle shown
in the illustration.
(22) Route the authentication unit cable through the
notch in the upper right cover.
(18) Attach the cover removed in step (13).
(Three screws)
Note:
Put the ferrite core inside the cover.
(23) Route the authentication unit cable through the
five wire saddles and pass it through the slot
shown in the illustration in the bracket on the
main body.
Note:
Make sure that there is no slack in cables at the
side of the working table.
(19) Refer to the installation manual for the Working
Table WT-506 and install the working table.
(20) Remove the upper right cover. (One screw)
(21) Remove the indicated knockout from the upper
right cover.
(24) Reinstall the upper right cover. (One screw)
(25) To install the covers and others removed in
steps (8) to (11), reverse the removal procedure.
E-5
(28) To install the covers, connector, and others
removed in steps (3) to (6), reverse the removal
procedure.
(26)

Refer to the installation manual for the Local
interface Kit EK-608 and install the local interface kit to the main body.
(29) Paste the authentication label to the position
shown in the illustration.
Note:
The authentication label is supplied with the Working Table.

Install the local interface board unit (three
screws) and connect the connector.
Note:
• The length of upper right screw A differs from
the other screws.
• Be careful not to pinch the harness.
• Route the cables through toward the front of the
unit.
Cable
3. Installation of the loadable device driver
Install the AU-201S loadable driver (ICC_LDR.tar) to
the main body.
(1) Prepare a USB memory where only the loadable
device driver is stored in the ROOT directory.
(Please do not save any other data in the USB
memory.)
(2) Connect the USB memory to the USB port of the
main body.
(3) Plug the power cord into the power outlet and
turn ON the power switch.
(4) Display the Service Mode screen.
(For details of how to display the Service Mode
screen, see the service manual.)
(5) Touch “System 2” →
→ “Driver Install.”
(6) Touch “SET” and press Start key to install the
data.
(7) Check that the data are normally installed from
the message that appears on the control panel.
(8) Turn OFF the power switch.
(9) Remove the USB memory.
(10) Turn ON the power switch.
Note:
When displayed the Service Mode screen, be sure
to turn off the power after exiting the Service Mode
screen and wait for 10 seconds or more before
turning on.
(27) Connect the USB cable to the local interface
board unit and wind the excess cable around
the three wire saddles.
Note:
Connect to the port at the near side.
E-6
4. Setting IC card authentication
(1) Display the Service Mode screen.
(For details of how to display the Service Mode
screen, see the service manual.)
(2) Display the Billing Setting screen.
(To display the Billing Setting screen, press Stop
→ 9 on the Control Panel.)
(3) Touch “Management Function Choice.”
(4) Touch “Authentication Device2.”
(5) Touch “Card.”
(6) Touch “END.”
(7) Turn OFF and ON the power switch.
Note:
When displayed the Service Mode screen, be sure
to turn off the power after exiting the Service Mode
screen and wait for 10 seconds or more before
turning on.
E-7

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
XMP Toolkit                     : 3.1-701
Producer                        : Acrobat Distiller 7.0 (Windows)
Create Date                     : 2015:01:09 15:14:11+09:00
Creator Tool                    : PScript5.dll Version 5.2.2
Modify Date                     : 2015:01:09 15:14:30+09:00
Metadata Date                   : 2015:01:09 15:14:30+09:00
Format                          : application/pdf
Title                           : 
Creator                         : .
Document ID                     : uuid:e69f2fd5-81db-4a54-995e-d176a18f0ffd
Instance ID                     : uuid:75152dd3-5ecb-468f-8307-3f16f657dcd7
Page Count                      : 7
Page Layout                     : SinglePage

EXIF Metadata provided by EXIF.tools