KTV Global LTW42DS 42" LCD TV Receiver/Monitor User Manual
KTV Global Corporation 42" LCD TV Receiver/Monitor Users Manual
Users Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 682292 |
| Application ID | vm6/itS6GxZ4APtmuHEQVg== |
| Document Description | Users Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 191.89kB (2398590 bits) |
| Date Submitted | 2006-07-18 00:00:00 |
| Date Available | 2006-07-18 00:00:00 |
| Creation Date | 2006-06-08 22:12:26 |
| Producing Software | Acrobat Distiller 4.05 for Macintosh |
| Document Lastmod | 2006-07-05 14:25:15 |
| Document Title | Users Manual |
User's Manual
32"/42" TFT LCD T V
Part No
2
Important Safety Instructions
1)
2)
3)
4)
5)
6)
7)
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in accordance with the manufacturer s
instructions.
8) Do not install near any heat sources such as radiators, heat registers, stoves, or
other apparatus (including amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized or grounding-type plug.
A polarized plug has two blades with one wider than the other. A grounding type
plug has two blades and a third grounding prong. The wide blade or the third
prong are provided for your safety. If the provided plug does not fit into your outlet.
Consult an electrician for replacement of the obsolete outlet.
10) Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
11) Only use attachments/accessories specified by the manufacturer.
12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer,
or sold with the apparatus. When a cart is used, use caution when moving the
cart/apparatus combination to avoid injury from tip-over.
13) Unplug this apparatus during lightning storms or when unused for long periods of
time.
14) Refer all servicing to qualified service personnel. Servicing is required when the
apparatus has been damaged in any way, such as power-supply cord or plug is
damaged, liquid has been moisture, does not operate normally, or has been
dropped.
15) The apparatus shall not be exposed to dripping or splashing and that no objects
filled with liquids, such as vases, shall be placed on the apparatus.
Important Safety Instructions
Shock Hazard Marking and Associated Graphical Symbols
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
Explanation of Safety Related Symbols
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION : TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK).
NO USER-SERVICEABLE PARTS
INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
This symbol is intended to alert the user to the presence of
uninsulated "dangerous voltage" within the product's enclosure
that may be of sufficient magnitude to constitute a risk of electric
shock to persons.
This symbol is intended to alert the user to the presence of
important operating and maintenance (servicing) instructions
in the literature accompanying the appliance.
WARNING - To Reduce The Risk Of Fire Or Electric Shock, Do Not Expose This
Apparatus To Rain Or Moisture.
Important Safety Instructions
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT
REMOVE COVER (OR BACK)
NO USER,SERVICEABLE PARTS INSIDE REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL
Before connecting the AC power cord to the DC adapter outlet make sure the voltage designation of
the DC adapter corresponds to the local electrical supply
Never insert anything metallic into the cabinet openings of the Liquid Crystal Display Television LCD:
doing so may create the danger of electric shock
To avoid electric shock never touch the inside of the Television LCD Only a qualified technician should
open the case of the Television LCD
Never use your Television LCD if the power cord has been damaged Do not allow anything to rest n the
power cord and keep the cord away from areas wherepeople can trip over it
Be sure to hold the plug not the cord when disconnecting the Television LCD from an electric socket
Openings in the Television LCD cabinet are provided for ventilation To prevent overheating these
openings should not be blocked or covered Also avoid using the Television LCD on a bed sofa rug or
other soft surface Doing so may block the ventilation openings in the bottom of the cabinet
If you put the Television LCD in a bookcase or some other enclosed space be sure to provide adequate
ventilation Put your Television LCD in a location with low humidity and a minimum of dust
Do not expose the Television LCD to rain or use it near water
(in kitchen near swimming pool etc) If the Television LCD accidentally gets wet unplug it and con,
tact an authorized dealer immediately You can clean the Television LCD with a damp cloth when nec,
essary but be sure to unplug the Television LCD first
Place the Television LCD on a solid surface and treat it carefully
The screen is made of thin glass with a plastic front surface and be damaged if dropped hit or scratched
Do not clean the front panel with keton,type materials (eg acetone) ethyl alcohol toluene ethylacid
methyl or chloride , these may damage the panel
Locate your Television LCD near an easily accessible AC outlet
General safety precautions
Thank you for purchasing our product.
Before using it, please read this user's manual carefully and apply it correctly and safely.
Please keep this manual close to you so you can refer to it anytime after reading it.
Also, for the transportation of the product, please attach this manual without fail.
Please observe the notes below.
1.
Use at the rated power voltage.
Use of non-rated voltage may cause fire, electric shock and breakdown.
2.
Do not open the cabinet and external cover.
The high voltage inside of this product may cause the electric shock.
3.
Do not remodel or disassemble this product.
Remodeling or disassembling in wrong method may cause fire, electric shock or breakdown.
4.
Do not insert or drop any foreign substance such as metals or flammable object inside from the air hole.
It may cause fire, electric shock or breakdown.
If any foreign substance is inserted inside of this product, turn off the power, pull the plug out of the socket and contact
the sales department. Do not use the product with the foreign substance in.
5.
Do not place any vase, potted plant, cup, medicine and any container with water on this product.
If the liquid is spilt, it may cause the fire, electric shock or breakdown.
6.
Do not place this product with water nor moisten it.
If water flows in it, it may cause the fire, electric shock or breakdown.
If there is water inside of the product, turn off the power immediately, pull the plug out of the socket and contact the
sales department.
Do not use the product with water in it.
7.
Never touch the antenna lie or power plug if it stars to thunder.
It may cause the electric shock.
8.
If any impact is applied, the parts inside of the product may be fallen out or broken to be the cause of fire, electric shock or
breakdown.
9.
Clean the dust on the power plug periodically.
The dusty power plug may cause the poor insulation due to the moisture to be the reason of fire.
10.
Do not destroy, process, make closer to heating device, bend or twist forcibly, place any heavy object on nor bind the
power cord or power plug. If it is used in the broken condition, it may cause fire or electric shock.
11.
Do not touch the power plug with wet hands.
If you pull in or out the power plug with wet hands, it may cause electric shocks.
12.
Put the power plug in firmly.
Putting the plug incompletely may cause the electric shock or fire by the generation of heat.
13.
Do not use any non-rated power socket with numerous devices jointed on one power socket or cable device.
The wire of non-designated capacity may cause the fire due to the generation of heat.
14.
In case of malfunction, turn off the power switch immediately and pull out the power plug.
If this product is used in the abnormal condition such as damage to it, foreign substance inside of the product, generation of joints, smelling, smoking, overheating and non production of signal, it may cause fire, electric shock or breakdown.
Turn off the power switch immediately, pull the power plug out of the socket and contact to the sales store..
15.
Leave space 10 cm or more from the wall for the installation of the device.
Do not install it close to the wall nor block the ventilation of the air.
Insufficient ventilation or accumulated heat inside of the product may cause the fire.
16.
Do not install it at the unstable location such as on the bouncing prop or tilted place.
It may be tipped over as it loses balance or damaged as it is fallen down.
General safety precautions
17. Do not install at the place with moisture or dust.
It may cause the fire or the electric shock
18. Do not install it at the place with poisonous gas.
It may cause the fire.
19. Do not install it at the location with continuous vibration.
It may be tipped over as it loses balance or damaged as it is fallen down.
20. Do not install it at the place on the strong magnetic field or current field.
It may cause fire, electric shock or break down.
This equipment may be observed deterioration of the picture by electromagnetic radiation in electromagnetic
environment.
21. Fasten the wheel of the product or shelf with wheels when installing this product.
If it moves or is tipped over, it may be damaged.
22. Do not leave it in the car under the burning sun for a long time.
The high temperature may distort the cabinet or the parts inside may be broken down or heated.
If you use this product in this condition, it may cause the fire, electric shock or breakdown due to the short circuit
or poor insulation.
23. Do not place any fire source such as candlelight close to this product or place it on this product.
If it is tipped over or fallen down, it may cause damage or fire.
24. Do not sprinkle water drops or water on this product.
It may cause the fire, the electric shock or breakdown.
25. Do not place heavy objects on this product.
It may be tipped over as it loses balance or damaged as it is fallen down.
26. Do not transport it with the power cord or the connection cable connected.
If you move this product with the power cord or the connection cable connected, the damaged power cord,
connection cable or connection terminal may cause the fire, the electric shock or breakdown.
27. Pull the power cord out while holding the plug portion.
If you pull the power cord out by force, the cord may the fire or the electric shock.
28. Do not use it outdoor.
Dust or rainstorm may cause the fire, electric shock or breakdown.
29. Do not climb on this product.
If you climb on it, it may damage or hurt it.
30. 2 persons or more shall transport the device, which is heavier than 18 kg.
If you drop or tip over the device, it may damage it.
The weight is indicated on the user's manual.
31. Use the attached power cord and connection cable, or those, which are indicated on the user's manual.
If you do not use the designated power cord and connection cable, it may cause the electric shock or breakdown.
32. Turn off the power switch when connecting the power cord or connection cable.
If you not turn off when connecting it, it may cause the electric shock or breakdown.
33. Do not use any chemical such as the paint thinner or benzine to clean the cabinet.
It may scratch the surface or disappear the indication to cause wrong operation, whch can be the reason for disorder.
34. Clean the cabinet with 5~6 time diluted neutral detergent water on smooth cloth as stirring to remove the
contamination.
After that, clean it with dry cloth to remove any stain.
Contents
I mportant Sfety Instructions . . . . . . . . . . . . . . . . . . . .3
G eneral Safety Precautions . . . . . . . . . . . . . . . . . . . .6
F ront Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
R ear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
A ccessory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
R emote Control Unit . . . . . . . . . . . . . . . . . . . . . . . . . .12
C onnecting to watch TV,VCR or DVD . . . . . . . . . . . . .13
S etup Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
P icture Configuration . . . . . . . . . . . . . . . . . . . . . . . . .20
S ound Configuration . . . . . . . . . . . . . . . . . . . . . . . . . .23
P IP(Picture In Picture) Selection . . . . . . . . . . . . . . . .25
F unction Selection . . . . . . . . . . . . . . . . . . . . . . . . . . .28
A djusting the PC Picture Settings . . . . . . . . . . . . . . . .35
S upport Timing Table (PC & HDMI) . . . . . . . . . . . . . .40
T roubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
S pecification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
Front Panel
1. TV/VIDEO
Display a menu of the available input sources.
2. MENU
Display the main on-screen menu. Exit from sub-menu.
3. VOL(-/+)
Press the increase or decrease the volume. Also used to increase
or reduce the value of a menu option.
4. CH( / )
Press CH
or CH
to change channels. Also used to highlight
selections on the on-screen menus.
5. POWER
Sub power switch
6. STAND BY
The color of LED is changed into RED.
7. ON
The color of LED is changed into GREEN.
8. Remote Control Sensor
9. POWER ON/OFF Turns ON/OFF the LCD TV/Video
Rear Panel
1. RS-232C JACK
2. HDMI
3. DVI AUDIO
4. PC D-SUB
5. PC AUDIO
6. COMPONENT 1
7. COMPONENT 2
8. AUDIO LINE OUT
9. S-VIDEO
10. A/V IN
Do not use this jack for customers.
Use to connect a video signal from a PC or DVD.
DVI to HDMI
Used to connect a video signal from a personal computer.
Connects to the sound-output port of a personal computer.
HDTV Input (Video signals from a HDTV player.
HDTV Input (Video signals from a HDTV player.
S-Video signal from an VCR or laserdisc player
Audio signals from VCR or similar device.(Audio input of A/V IN is used
commonly with SVHS)
11. USB V.2.0 (For Service) * SPDIF OUT (Optical/Coaxial) may have the signal compatibility problems
12. SPDIF (Optical)
with certain A/V receiver and this is known issues. Due to the problems, it
may have difficulty in output sound.
13. SPDIF (Coaxial)
14. ANTENNA JACK Connect to an antenna or a cable TV system
Use 100-250V AC, 50/60 Hz.
15. AC INLET
To prevent electrical shocks and fire hazards, do not use any other
power source.
10
Accessory
Inserting the batteries in the remote controller
You must insert or replace the batteries in the remote controller when you:
Purchase the set.
Find that the remote controller is no longer operating correctly.
Remove the cover of the
remote controller by pressing
the symbol and pulling the
cover space in the direction
of the arrow.
You can use your remote controller within a distance of 7-10m and an angle of 30
degrees from the left and right sides of the remote controller receptor of your monitor.
Insert 2 batteries(AAA size),
taking care to respect the
polarities.
Replace the cover by put in
it in the direction of the
arrow.
11
Remote Control Unit
1. MUTE Button
(Press to temporarily cut of the sound)
2. SLEEP Button
3. CCD Button
4. Numeric Buttons (Direct Channel select.)
5. Q-VIEW Button (Quick view for previous channel)
6. EPG Button (User can check about present channel,
next program list and information by selecting the
EPG key.)
7. VOLUME Up(+) / Down(-) Button
Channel Up(+) / Down(-) Button
/ Button
(This buttons are used to make adjustments to the
selected menu item)
8. MENU Button
9. PC/HDMI Button (Select PC or HDMI mode)
10. DTV/TV Button (Select DTV or TV)
11. P.STD Button (Picture Standard Button)
12. MTS Button (Multi Channel Television Stereo):
Sound mode change to Stereo, Mono, or
Separate Audio Program (SAP Broadcast)
13. POWER button (Turns the TV On and Off)
14. SIZE Button (Image size button)
15. STILL Button (Pause the moving Image)
16. - Button (DTV Channel Select Button)
17. F.CH Button (User can add the wanted channel to
favorite lists during watching TV)
18. ENT Button
19. EXIT Button (Terminated menu screen)
20. AV.SEL Button (Change input source every time
pushed)
21. SOURCE Button (Display the all the connected or
available external devices on the screen)
22. S.STD Button (Sound Standard Button)
PIP SELECTION
23. PIP Button (Turn Picture-In-Picture on or off)
24. SIZE Button (Adjusts the sub picture size)
25. SOURCE(SUB) Button
26. POSITION Button (Change the position of sub
Picture)
27. SWAP Button (Exchange main with sub picture)
12
Connecting to watch TV, VCR or DVD
Connecting the Aerial or Cable Television Network
To view television channels correctly, a signal must be received by the set from one of following
sources:
An outdoor aerial
An indoor aerial (not recommendable)
A cable television network
1. In the first three cases, connect the aerial or network input cable to the 75 ohm coaxial socket
on the rear of the TFT LCD TV.
2. Press the TV button on the remote control.
Connecting the VCR, DVD or Other external devices
1. Connect video and audio cable according to the shape and color or the video / audio cable.
When an external devices is in MONO, the audio connection cable can be connected to
either the left and S.MODE/MTS should be set MONO.
2. For optimal visual image, use S-VIDEO connector instead of video (yellow) connector.
13
Connecting to watch TV, VCR or DVD
Connecting a DVD Player (Connecting to Y, Pb, Pr)
1. Connect a set of audio cables between the component AUDIO IN jacks on the TFT
LCD TV and the AUDIO OUT jacks on the DVD Player.
2. Connect video cables between the Y, Pb and Pr inputs on the TFT LCD TV and Y, Pb
and Pr outputs on the DVD Player.
(Note : For an explanation of Component video, see your DVD Player's Owner's
manual.)
Sound
Cable
HDMI
Cable
DVI to HDMI
Cable
HDMI Connection
DVI to HDMI Connection
DVD Player/Video Game Machine
14
Setup Selection
Scanning Channels (Automatic)
This will scan all the available Channels. Channel scan should be done before using this product.
You should set the proper TV reception method, 'Air' for outdoor air antenna and 'STD, HRC & IRC' for
your cable
TV System. For the cable system, please contact your local cable TV provider.
1. Press MENU button on the remote control and
navigate by pushing [ ] or [ ] Keys to select
'Channel' menu.
2. Press [ ] or [ ] button to enter [Setup]
Menu.
3. Set your TV reception method among
[Air/Cable/Hrc/Irc],
To do channel search, set the TV reception method, such as 'Air', 'Cable STD',
Cable Hrc' or 'Cable lrc'. All the available Digital
(ATSC) and Analog (NTSC) TV channels are
scanned in each TV reception method and stored
after the channel scan. When you watch TV, the
channel system is set to DTV as a factory default.
4. Push [ ] or [ ] button to select [Auto Search]
and press [ ] or [ ] button again, and then
the channels are searched automatically
5. Press [ ] or [ ] button to display the scanned
channels. Only scanned channels are on display
All the current stored channels will be
replaced with new channel information
after doing 'Auto Search'.
15
Setup Selection
Setup Edit-Store or Delete the Channels
1. Press MENU button and select [Setup] menu
by manipulating [ ] or [ ] button and then,
press [ ] button to get into.
2. In this menu, select [Setup Edit] by pressing
[ ] or [ ] button.
3. Setup Edit menu will be up when you press
[ ] button.
Channel Edit mode manages Digital and
Analog channels separately.
(For example, only available DTV channels will be
displayed in DTV mode, no analog channels at all).
It is recommend setting the channel system
(Analog/Digital) proprly before you edit channel.
Digital Channel
Analog Channel
* The right side of the menu is for the current available or stored channels. Before you watch TV, as
mentioned, channel scan should be done.
To Store/Memorize a Channel
1. Press ENT [ ] button on the one you select and then input Channel Number.
2. Press ENT [ ] button again and the channel configurations will be stored.
To Delete a Channel
1. Select the channel you would like to delete by manipulating [ ] or [ ] or [ ] or [ ] button on
Remote Controller.
2. Press '-' button to delete the selected one.
16
Setup Selection
Using Favorite (FAV.) Channel Function
Favorite Channel Function is to ease channel change among your frequent watching or favorite channel by separately memorizing them in FAV.
To Register as Favorite Channel
1. Press [ ] or [ ] button or [ ] or [ ] button to select the channel you would like to register in the
available channel menu on the right side of display.
2. Press 'FAV' on the selected one to register it as a favorite channel
3. The registered one is displayed in 'Favorite Channel', located at the bottom left of the screen.
Digital TV Channel
Analog TV Channel
* After you finish favorite channel registration, by each pressing of FAV, you can change the channels
between them.
FAV function manages Digital TV
Channels and Analog ones separately.
For instance, if FAV button is pressed under
Digital TV System(DTV), only DTV channels that
is preset channels are displayed. To use in
Analog, press DTV/TV button on Remote
Controller to change the mode to Analog and
push FAV.
17
Setup Selection
Displaying EPG(Electronic Program Guide
EPG is available only when you watch Digital TV.
EPG displays TV Programs with reference to a
channel and time interval.
1. Press EPG button on the remote control during watching HD TV Program.
2. Press [ ] or [ ] or [ ] or [ ] button to navigate Programs with reference to each channel.
3. You can check the program schedule with
reference to a channel and see program
information by pushing 'OK'.
*Not every program has EPG information.
The program with information has information icon in EPG.
Viewing the Information
The information identifies the current channel
and status of certain audio and video settings.
1. Press ENT [ ] button on the remote control
during watching TV.
2. The TV will display information on the channel, the type of sound and status of certain
audio/video settings.
3. The information screen automatically disappears after about ten seconds or manually
by pushing ENT [ ] button again.
The information window will disappear
about 10 seconds later.
18
Setup Selection
Changing the input mode
This explains how to change and watch other
Input Sources by pushing AV.SEL buttons
1. Press [AV.SEL] button on the Remote control.
2. You can change Input Source to be displayed every time you press the button. It
changed among the connected source only.
* You can select TV, PC/HDMI Mode directly
by pressing [DTV/TV] / [PC/HDMI] button on
the remote control accordingly.
Concerning how to connect external
devices, you can consult "Installation"
section.
Viewing the Current Connected External Devices
This explains how to change and watch other
Input Sources by pushing 'Source' button.
1. Press [Source] button on the remote control.
The status of input source will appear.
2. Press [ ] or [ ] button and then push ENT
[ ] button to change the input source.
* The Connected (Available) external devices
or port is brightened with "Connected" message while deactivated ones are in gray and
with "Not Connected" message.
19
Picture Configuration
Adjusting the Aspect Ratio
This explains how to change Aspect Ratio to
'4:3, 14:9, Panorama and Wide'.
Press [SIZE] button on the remote control. The
Aspect Ratio is changed in turn as you press
the button.
Wide
Panorama
Zoom
4:3
14:9
To change the Aspect Ratio in OSD Menu
1. Press MENU button on the remote control.
2. Press [ ] or [ ] button to select '[Picture]
menu and push ] button.
3. In [Picture] menu, select [Size] with [ ] or
[ ] button.
4. Change Aspect Ratio by pressing [ ] or [ ]
button.
Wide
Panorama
Zoom
4:3
14:9
20
Convert display ratio to 16:9
Panorama Mode
Zooming the original Image
(Press [ ] or [ ] button to move
the center position of picture.)
Convert display ratio to 4:3
Convert display ratio to 14:9
Picture Configuration
Changing the Preset Picture Mode
Your TV has several factory presets which
allow you to control the picture.
Press [P.STD] button on the remote control.
The picture mode is changed as you press the
button.
Custom Dynamic Standard Movie
Mild
To change the Picture mode in OSD Menu
1. Press MENU [ ] button on the remote control.
2. Press [ ] or [ ] button to select [Picture]
menu and push Volume [ ] button.
3. In [Picture] menu, select [Picture Mode] with
[ ] or [ ] button.
4. Change the Picture mode by pressing [ ] or
[ ] button.
Customizing the Picture
You can adjust Brightness, Contrast,
Sharpness or the depth of Color.
1. Press MENU button on the remote control.
2. Press [ ] or [ ] button to select [Picture]
menu and push [ ] button.
3. In [Picture] menu, select [Picture Mode] with
[ ] or [ ] button and manipulating [ ] or [ ]
button until "Custom" appears.
4 Use [ ] or [ ] button to select among
Brightness, Contrast, Sharpness, Tint and
Color and then adjust the values with [ ] or
[ ] button.
21
Picture Configuration
Adjusting the Color Tone
This explains how to change the tone of the
screen.
1. Press MENU button on the remote control.
2. Press [ ] or [ ] button to select [Picture]
menu and push [ ] or [ ] button.
3. In [Picture] menu, select [Color Tone] with
[ ] or [ ] button
4. Change Color Tone Preset with [ ] or [ ]
button.
22
Sound Configuration
Changing the Preset Sound Mode
This TV set offers five sound modes (Custom,
Standard, Music, Movie, Speech).
Press [S.STD] button on the remote control.
The mode is changed one by one every time
you press it.
Custom
Speech
Standard
Music
Movie
To change the Sound mode in OSD Menu
1. Press MENU button on the remote control.
2. Press [ ] or [ ] button to select [Sound]
menu and push [ ] button.
3. In [Sound] menu, select [Sound Mode] with
[ ] or [ ] button.
4. Change the Sound Mode by pressing [ ] or
[ ] button.
Adjusting the Equalizer
This explains how to set and adjust equalizer.
1. Press MENU button on the remote control.
2. Press [ ] or [ ] button to select [Sound]
menu and push [ ] button.
3. In [Sound] menu, select [Equalizer] with [ ]
or [ ] button and push [ ] button.
4. Select the Frequency to be set by pressing
[ ] or [ ] button.
5. Adjust the level properly by pressing [ ] or
[ ] button.
23
Sound Configuration
Automatic Volume Level Control
Auto Volume normalizes the different sound
volume level that can be different in broadcast
station. This lets you have adjusted mean value
of volume level per channel.
1. Press MENU button on the remote control to
select [Sound] menu.
2. Press [ ] button on [Sound] menu.
3. Press [ ] or [ ] button to select [Auto
Volume].
4. Push [ ] or [ ] button until [Auto Volume] is
"on".
Setting MTS (Multi Track Sound) Mode
You can adjust the Stereo or MTS function
manually.
Press [MTS] button on the remote control.
Stereo / Mono
You can select between 'Stereo' and 'Mono'
when the Stereo broadcasting is received.
Stereo: Two speakers out (2 Channels,
Left/Right) and the different sound per
channel
Mono: Two speakers out but both channel has the same signal (the identical sound).
SAP Stereo / SAP Mono
You can select the SAP mode which is 'SAP Stereo', 'SAP Mono' when the SAP broadcasting,
which is usually a foreign translation, is received. The mode is automatically detected.
SAP Stereo: There is at least one more dubbing language in addition to default language in
incoming broadcasting signal. You can change the language by pushing [MTS] button
SAP Mono: Only default language is on air.
* STEREO, MONO, SAP Stereo and SAP Mono modes are automatically detected. You just
press the key to toggle the each mode.
24
PIP(Picture In Picture) Selection
PIP is the function to display two different input
source simultaneously.
1. Press [PIP] on the remote control.
[PIP] is changed as following every time you
press [PIP] button
On Off
To set PIP in On Screen Display Menu
1. Press MENU button on the remote control.
2. Select PIP menu by pressing [ ] or [ ] button.
3. Press [ ] button and select [PIP] by pressing [ ] or [ ] button
4. Set PIP to "On" with [ ] or [ ] button
* Please check the following PIP combination table of Main and Sub picture.
('Graphic-in-Graphic or Video-in-Video' is not
supported)
25
PIP(Picture In Picture) Selection
Adjusting the Size of Sub picture
Press [SIZE] button on the remote control.
The size is changed in the following order each
press.
Small DOUBLE DOUBLE2
To adjust the size in On Screen Display
Menu
1. Press MENU button on the remote control.
2. Select PIP menu by pressing [ ] or [ ] button.
3. Press [ ] button and select [Size] by pressing
[ ] or [ ] button.
4. Press [ ] or [ ] button to adjust the size.
Changing Input Source of Sub picture
You can change the input source of sub picture.
Press [P.INPUT] button on the remote control.
The input source is changed as you press the
button. Source change will be available only
among connected sources. For more information, check the PIP Combination table.
To change the input source in On Screen
Display Menu
1. Press MENU button on the remote control.
2. Select PIP menu by pressing [ ] or [ ] button.
3. Press [ ] button and select [Input Source]
by pressing [ ] or [ ] button.
4. Press [ ] or [ ] button to change input
source.
(To adjust the input source of Sub picture,
PIP should be active.)
26
PIP(Picture In Picture) Selection
Adjusting the position of Sub picture
You can change the position to 'Up', 'Down',
'Left', 'Right'.
The position of Sub picture is changed as you
press [POSITION] button on the remote control.
To adjust the position in On Screen Display
Menu
1. Press MENU button on the remote control.
2. Select PIP by pressing [ ] or [ ] button.
3. Press [ ] or [ ] button.
4. Select [Position] by pressing [ ] or [ ] button.
5. Adjust the position by pressing [ ] or [ ]
button
(To adjust the position of Sub picture, PIP
should be active.)
Swapping the main with sub picture in PIP mode
Press [SWAP] button on the remote control.
To do this in On Screen Display Menu
1. Press MENU button on the remote control.
2. Select PIP by pressing [ ] or [ ] button.
3. Press [ ] button.
4. Select [SWAP] by pressing [ ] or [ ] button.
5. Pressing [ ] or [ ] button to swap the picture
27
Function Selection
Changing the OSD Menu language
You can change the OSD Menu Language.
1. Press MENU button on the remote controller
2. Press [ ] or [ ] button to select [Set Up]
menu and push [ ] or [ ] button
3. In [Set Up] menu, select [Language] with [ ]
or [ ] button.
4. Change Language by pressing [ ] or [ ]
button.
Setting the Blue Back Screen
If no signal is being received or the signal is
very weak, a blue back screen is automatically
displayed instead of the
noisy image.
1. Press MENU button on the remote control.
2. Press [ ] or [ ] button to select '[Setup]'
menu and push [ ] button to be in.
3. Select [Blue Screen] by pressing [ ] or [ ]
button.
4. Set 'On' by pressing [ ] or [ ] button.
28
Function Selection
Setting the Current Time (Time Zone)
Time Zone setting is required for setting the
time and receiving EPG properly. Once system
time is set, all the relevant functions such as
timer are available.
1. Press MENU button on the remote control.
2. Select Setup menu by pressing [ ] or [ ]
button.
3. Press [ ] button, select 'Time' with [ ] or [ ]
button and press [ ] button again.
4. In [Time Zone] menu, manipulate [ ] button
to select the region you live.
The current time can be check by pressing
ENT[ ]button on the remote controller.
Automatic Power On and Off
1. Press MENU button on the remote control.
2. Select Setup menu by pressing [ ] or [ ]
button.
3. Press [ ] button, select 'Time' with [ ] or [ ]
button and press [ ] button again.
4. Select 'On timer' or 'Off timer' by pressing
[ ] button.
5. Set the time with [ ] or [ ] button.
29
Function Selection
Setting the Sleep Timer
You can adjust the time for automatic system
down.
Press [Sleep] button.
Sleep Timer is changed as following every time
you press [Sleep] button.
OFF
30Min
60Min
90Min
120Min
150Min
180Min
To set the sleep timer in [Setup] menu.
1. Press MENU button on the remote control.
2. Select Setup menu by pressing [ ] or [ ]
button.
3. Press [ ] button, select 'Time' with [ ] or [ ]
button and press [ ] button again
4. Select [Sleep Timer] by pressing [ ] or [ ]
button.
5. Set the timer with [ ] or [ ] button
6. When configuration is done, press MENU
button to save the changes and exit.
Time is automatically set, once you set the
Time Zone and then watch a DTV channel. After Time is set, you can use On Timer and
Off Timer functions.
The current time is automatically received
or synchronized by Digital TV EPG once
Digital TV channel information is set and stored, it
is not required for setting the time.
30
Function Selection
Pixel Shift
Due to its fundamental and built-up technology
of LCD, when it is turned on long time of period
especially with a still image, it can have afterimage that does not disappear even though it is
turned off. During watching TV, this can affect
serious image quality problem. However, with
this feature, each pixel of LCD is shifted to right
or left minutely and regularly, surely impossible
to be noticed by human eyes, to protect afterimage effect.
1. Press MENU button on the remote control.
2. Select 'PIXELSHIFT' or 'SCREEN WIPER' in
Setup menu.
3. Set 'PIXELSHIFT' or 'SCREEN WIPER'
function 'ON' by pressing [ ] or [ ] button.
* If Screen Wiper is on, in some of time, a vertical white bar will be moving from right to left
or vice versa every 3 minutes.
Digital Noise Reduction
When the incoming signal is weak or picture
noise appears at moving image, DNR function
helps to reduce
the noise and eye strain by its filtering procedure.
1. Press MENU button on the remote control.
2. Select 'DNR' in Setup menu.
3. Set 'DNR' function 'ON' by pressing [ ] or
[ ] button.
31
Function Selection
Viewing Closed Caption
Closed Caption feature is to display On Screen
Text Messages during watching TV. This feature is available in both analog and digital
broadcast.
1. Press MENU button on the remote control,
select Setup menu by manipulating [ ] or
[ ] button and press [ ] button.
2. Press [ ] or [ ] to select [Caption] and then
[ ] button
3. 'Caption' sub menu will appear.
Sub Menus of Caption
Caption
: Turn the feature on or off.
This can be set by [ ] or
[ ] button.
Caption Box
: Set the Text Box. You can
turn it on or off with [ ] or
[ ] button.
Caption Box Color : change the color of
Caption Box. Press [ ] or
[ ] button to change it.
32
Function Selection
Parental Rating Control (V-Chip)
V-chip feature automatically locks TV Programs
(TV Parent Guide Lines) or Movie (MPAA) that
is considered as inappropriate for children. To
activate, deactivate or set the rating, you should
enter a PIN (Personal ID Number).
1. Press [MENU] button to display the menu.
2. Press [ ] or [ ] button to select 'Setup', and
then press [ ] or [ ].
3. Press [ ] or [ ] button to select 'V-Chip',
and then press [ ] or [ ].
4. The message "Enter PIN" will be appear.
Enter your four digit PIN Number.
The V-Chip screen will appear.
(*The default Pin Number of a new TV set is
'0000'.)
* To change PIN Number, select Change Pin
Number menu and then the menu will appear.
Choose and enter 4 digits.
How to set up restrictions using the "TV Parental Guidelines".
1. Press [ ] or [ ] button to select 'TV Parent Guide Lines' and then push [ ] or [ ] button.
The menu will appear. You can set up the restrictions in this menu.
* Restriction Categories based on six aged base.
TV-Y
TV-Y7
TV-G
TV-PG
TV-14
TV-MA
Young Children
Children 7 and over
General Audience
Parental Guidance
Viewers 14 and Over
Mature Audience
33
Function Selection
For instances, if you block TV-Y, TV-Y7 will automatically be blocked and similarly, if you block the TVG, all the categories in "young adult" (TV-Y, TV-Y7, TV-G, TV-PG, TV-14, and TV-MA) will be blocked.
* Each Restriction Category has additional options, sub-ratings.
FV: Fantasy Violence
D: Sexually Suggestive Dialog
L: Adult Language
S: Sexual Situation
V: Violence
V-Chip will automatically block certain sub-categories that are more restrictive. For example, if you
block "L" sub-rating in TV-PG, then the "L" sub ratings in TV-14 and TV-MA will automatically be
blocked.
How to set up restrictions using the "MPAA"
1. Press [ ] or [ ] button to select 'MPAA Rating" and then push [ ] or [ ] button. The menu will
appear. You can set up the MPAA restrictions in this menu.
* Restriction Categories based on six aged base.
PG
PG-13
NC-17
NR
34
General Audience (No Restrictions)
Parental Guidance Suggested
PG-13 (Parents Strongly Cautioned)
R (Restricted. Children under 17 should be accompanied by an adult)
No Children under age 17.
X (Adults Only)
Not Rated
Adjusting the PC Picture Settings
Connecting a PC
1. Turn off your computer and LCD TV.
2. Connect a PC D-sub cable between your PC and PCVIDEO-IN of the LCD TV.
And then fasten the screws of both sides of the cable.
3. Connect a PC Audio cable between the sound output
jack of the sound card on a PC and the PC-AUDIO-IN
of the LCD TV.
4. Power on the computer before turning on the LCD TV.
Initial set PC mode
1. Power on your LCD TV by pressing the POWER button on the main set or on the remote controller.
2. Press the PC/HDMI button on the remote controller
to switch to the PC mode.
Then the PC screen is automatically set.
When a CD-Title runs, the music is output from
speakers.
(You can use an external speaker via the Audio
Output jack on the rear of the main set.)
35
Adjusting the PC Picture Settings
Using as a PC Monitor
This LCD TV is designed to be used as a PC
Monitor. Concerning the Maximum Resolution,
please refer to specification table in Appendix.
Since it has driver software implemented, you
don't have to install any additional software.
Just PLUG N' PLAY!!!
To use it as a PC monitor, your PC and
TV should be connected via D-sub cable
(15 Pin Analog). For details, please check the
Installation section.
Check the current Resolution and Frequency rate
This will display information on current resolution and frequency rate on the bottom of the
screen. To check, press MENU button and
select 'Picture menu'.
1. Select 'PC' and press [ ] or [ ] button.
2. The resolution and Frequency rate are displayed on the bottom of the screen.
Automatic Adjustment of the PC picture
This is the function that the LCD TV System
finds the optimal value for adjustment and automatically applies it. Use this function when the
position of WINDOWS image is not centered or
the characters on the screen are not clear.
1. Press MENU [ ] button on the remote control.
2. Press [ ] or [ ] button to select [Picture]
menu and push [ ] button.
3. In [Picture] menu, select [PC] with [ ] or [ ]
button and push [ ] button.
4. Select 'Auto Adjustment' by pressing [ ] or
[ ] button
5. Press [ ] button and then Automatic adjustment starts.
36
Adjusting the PC Picture Settings
Setting the Position of PC Picture
You can adjust the position of a PC picture
manually. Use this function when the picture is
not centered or shifted to sides.
1. Press [ ] or [ ] button.
2. Press [ ] or [ ] button and then select
'Position' by pressing [ ] or [ ] button.
3. The position adjustment screen is displayed
when you press [ ] or [ ] button.
4. Adjust the position by pressing [ ] or [ ]
button and [ ] or [ ] button.
Adjusting the PC Picture Size
This explains how to set the screen size of PC.
1. Press MENU button on the remote control.
2. Press [ ] or [ ] button to select [Picture]
menu and push [ ] button.
3. Select [Picture Size] by pressing [ ] or [ ]
button and adjust the value with [ ] or [ ]
button.
PC Picture Size
Wide - Full Screen
Real - Display Real Resolution
4:3
- Display in 4:3 aspect ratio
37
Adjusting the PC Picture Settings
Adjusting the PC Picture Settings
You can adjust the PC picture, by selecting the
preset values or user value. In this Menu, you
can adjust Brightness, Contrast and Sharpness.
To use the preset values
1. Press MENU button on the remote control.
2. Press [ ] or [ ] button to select [Picture]
menu and push [ ] button.
3. Select [Picture Mode] by pressing [ ] or [ ]
button and adjust the value with [ ] or [ ]
button.
Adjusting the Color Tone
You can adjust the color tone of the PC Picture.
1. Press MENU button on the remote control.
2. Press [ ] or [ ] button to select [Picture]
menu and push [ ] button.
3. Select [Color Tone] by pressing [ ] or [ ]
button and press [ ] button.
4. [Color Tone] Menu will display.
5. Adjust RGB by pressing [ ] or [ ] button
and [ ] or [ ] button.
38
Adjusting the PC Picture Settings
Adjusting the Frequency/Fine Tune
Use this function to adjust the Frequency range
or Phase.
To adjust the Frequency by using On
Screen Display Menu
1. Press MENU button on the remote control.
2. Press [ ] or [ ] button to select [Picture]
menu and push [ ] button.
3. Select [PC] by pressing [ ] or [ ] button and
press [ ] button.
4. Press [ ] or [ ] button to select [Frequency]
or [Phase].
5. Press [ ] or [ ] button to adjust the
Frequency range or phase
39
Support Timing Table (PC & HDMI)
40
Support Timing Table (PC & HDMI)
41
Troubleshooting
If you have a problem setting up or using your LCD TV, you may be able to solve it yourself.
Before contacting customer service, try the suggested actions that are appropriate to your problem.
42
What you see...
Suggested Actions
Screen is blank and
power indicator is off
Ensure that the power cord is firmly
connected and the LCD TV is on.
"Check to Signal"
message
Ensure that the signal cable is firmly connected to the
PC(D-Sub) sources.
Ensure that the PC(D-Sub) are turned on.
The image is too light or too dark
Adjust the Brightness and Contrast.
Vertical bars appear to flicker,
jitter or shimmer on the image
Adjust the Frequency function.
Auto Tracking will clear it automatically.
Horizontal bars appear to flicker, jitter or shimmer on the image.
Adjust the phase function and then adjust the clock
function.
Auto tracking will clear it automatically.
Screen is blank and power
indicator light is steady red
The monitor is using its power management system.
Move the computer's mouse or press a key on the
keyboard.
Image is not stable and
may appear to vibrate
Auto tracking will clear it automatically
Check that the display resolution and frequency from
your PC or video board is an available mode for your
monitor.
On your computer check:
Control Panel, Display, Settings
Image is not centered on the screen.
Auto tracking will set the best position automatically
Adjust the horizontal and vertical position.
Troubleshooting
Problem
Suggested Actions
No sound
Ensure that the audio cable is firmly connected to
both the audio-in jack on your monitor and the audioout jack on your sound card.
Check the volume level.
Sound level is too low
Check the volume level.
If the volume is still too low after turning the control to
its maximum, check the volume control on the
computer sound card or software program.
Sound is too high pitched or
too low pitched
Adjust the Treble and Bass to appropriate level.
TV signal is not received
Ensure that the antenna cable is firmly connected to
the VHF/UHF jack.
Check "Channel Memory" and make sure you
choose the correct channel system.(PAL Model)
Select "Auto Tuning" to configure the channel
system automatically.(PAL Model)
43
Specification
SPECIFICATION (32")
Panel
TFT Color LCD
Panel Type
697.685 x 392.256mm
Display Area
16.7 million
Display Color
0.17 x 0.51 x RGB mm
Pixel Pitch
Recommended Resolution 1366 x 768
Analog RGB 15 pin D-sub
PC Audio Input
Analog RGB 15 pin D-sub
PC Audio Input
Video
Composite Input
S-Video In
DVD (Y, Pb, Pr) Input
HDMI Input
Composite Input
S-Video In
DVD (Y, Pb, Pr) Input
HDMI Input
Composite Input
PC Input
Component (Y,Pb,Pr)
Audio Line Out(RCA Stereo L/R)
DVI to HDMI (RCA Stereo In)
SPDIF (Optical)
SPDIF (Coaxial)
Composite Input
PC Input
Component (Y,Pb,Pr)
Audio Line Out(RCA Stereo L/R)
DVI to HDMI (RCA Stereo In)
SPDIF (Optical)
SPDIF (Coaxial)
EPG
NTSC, ATSC, (PAL M and PAL N)
Dolby AC-3
MPEG 1/2 Layer 1 & 2
EPG(Electronic Program
Guide) with ATSC
PSIP(Program and Service
Information Protocol)
NTSC, ATSC, (PAL M and PAL N)
Dolby AC-3
MPEG 1/2 Layer 1 & 2
EPG(Electronic Program
Guide) with ATSC
PSIP(Program and Service
Information Protocol)
Certifications
Power Consumption
Speaker
Plug & Play
Screen Control
Weight
Power Supply
Remote Controller
Dimension
CE
116W
10W x 10W
DDC 2 B
On Screen Display Menu
Net 21Kg / Gross 24.5Kg
AC 100-250V~
Yes
808 (W) x 643 (H) x 243 (D)
CE
220W
10W x 10W
DDC 2 B
On Screen Display Menu
Net 34Kg / Gross 40Kg
AC 100-250V~
Yes
1063(W) x 830(H) x 290(D)
Audio
Others
44
TFT Color LCD
930x 523mm
16.7 million
0.227 x 0.681 x RGB mm
1366 x 768
PC
In/Out
TV
Signal
SPECIFICATION (42")
Video System
Sound System (ATSC)
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No XMP Toolkit : 3.1-702 Create Date : 2006:06:08 22:12:26Z Modify Date : 2006:07:05 14:25:15+09:00 Metadata Date : 2006:07:05 14:25:15+09:00 Producer : Acrobat Distiller 4.05 for Macintosh Format : application/pdf Document ID : uuid:94595a04-b678-40fc-b623-191f1606e713 Instance ID : uuid:a1c27e64-f1be-4466-b56b-46116e26634d Has XFA : No Page Count : 45EXIF Metadata provided by EXIF.tools