KYE SYSTEMS GMZKB TOUCH MOUSE 6000 (GM-120017/T) User Manual

Download:
Mirror Download [FCC.gov]
Document ID	1853087
Application ID	5fY4yi+WZLob11fEWkI1kA==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	23.15kB (289408 bits)
Date Submitted	2012-12-05 00:00:00
Date Available	2013-06-03 00:00:00
Creation Date	2012-11-22 11:01:09
Producing Software	GPL Ghostscript 8.15
Document Lastmod	2012-11-22 11:01:09
Document Title	(Microsoft Word - \275\306\273s -Manual 01-Touch Mouse 6000-ENG.doc)
Document Creator	PScript5.dll Version 5.2.2
Document Author:	Paul1106

English
Touch Mouse 6000 User Manual
Hardware Installation
1. Install one AA or two AA batteries in the mouse as instructed.
2. Connect the receiver to a USB port of a PC.
3. Make sure that you have switched on the power switch underneath the mouse.
Power on the mouse
Plug in the receiver
Using the Mouse
1. Click: The Touch Mouse provides full 2-button operation. Press the left or right area of the mouse surface. (For Windows 8/7)
Left-click
Press the left side of
the touch surface.
Right-click
Press the right side
of the touch surface
Vertical Wheel
Vertical Wheel
Scroll (Up)
Scroll (Down)
2. Press the top 1/2 of the touch strip to go to the Windows Start screen (Metro Start in Windows 8).
3. Battery low indication: If the LED is flashing, then the battery level is low, you need to replace battery immediately.
4. For Window 8 Gestures
Gestures
Description
Edge Swipe (Left)
Swipe from the far
left edge of the
surface to the right.
Gestures
Description
Edge Swipe (Right)
Swipe from the far
right edge of the
surface to the left.
Vertical Wheel
Vertical Wheel
Scroll (Up)
Scroll (Down)
Horizontal Wheel
Horizontal Wheel
Scroll (Left)
Scroll (Right)
Adjust View
Adjust View
(Zoom in)
(Zoom out)
Edge Swipe (Top)
Note:
You are prompted to install Touch Mouse 6000 software that enhances your Touch Mouse experience with gestures. Download the software driver from our website: www.geniusnet.com
Warning: (Troubleshooting)
1. Do not use the wireless optical/IR mouse on a desk which is made of glass or mirror.
2. The connection of the wireless device is factory preset, so when you plug the USB receiver into any USB port, the connection between the micro receiver and the mouse will be established automatically.
3. In case your PC did not install the hardware successfully, remove the micro receiver from the USB port and go Human Interface Devices under Device Manager to remove the mouse then plug in the micro
receiver to a USB port again.
4. If you feel the mouse does not move smooth as usual, it is possible the battery has lost its charge so you need to replace it. Remember to put the battery in the correct direction.
English
FCC ID: FSUGMZKB
FCC Compliance and Advisory Statement
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, according to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try correct the interference by one or more of the following
measures:
1. Reorient the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into and outlet on a circuit different from that to which the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.
Any special accessories needed for compliance must be specified in the instruction manual.
Warning: A shielded-type power cord is required in order to meet FCC emission limits and also to prevent interference to the nearby radio and television reception. It is essential that only the supplied power cord be used. Use only shielded cables to
connect I/O devices to this equipment.
CAUSION: Any changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.
IC statement: This Class B digital apparatus complies with Canadian ICES-003.Cet appareil numĂŠrique de la classe B est conforme Ă  la norme NMB-003 du Canada.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Page Count                      : 2
Producer                        : GPL Ghostscript 8.15
Create Date                     : 2012:11:22 11:01:09
Modify Date                     : 2012:11:22 11:01:09
Title                           : (Microsoft Word - \275\306\273s -Manual 01-Touch Mouse 6000-ENG.doc)
Creator                         : PScript5.dll Version 5.2.2
Author                          : Paul1106

EXIF Metadata provided by EXIF.tools