Kangaroo TX600-845C Electric Cart Remote Control User Manual caddiecommand manual NEWSTYLE
Kangaroo Products Company Electric Cart Remote Control caddiecommand manual NEWSTYLE
Kangaroo >
Kangaroo CaddieCommand Radio System Users Manual SEE RED TEXT FOR FCC INFO
KK
KK
Kangang
angang
angarar
arar
aroooo
oooo
oo
CadCad
CadCad
CaddieCommanddieCommand
dieCommanddieCommand
dieCommand®
Kangaroo Products Company, 108 Mill Spring Road, Columbus, NC 28722
(828) 894-8241
U.S. Patent no. 5,265,686
caddie@kangaroogolf.com
Serial Number — 6000 and up
Radio Transmitter/Receiver Model TX600-845C
RX600-840C
Congratulations to you on your selection and purchase of CaddieCommand, the very best
motorcaddie remote control system available. It is the perfect complement to the world’s
finest motorcaddie, your Hillcrest.
What you have acquired is a superbly conceived, meticulously fabricated, and
sensibly operated remote control system which will provide many years of satisfying
service to you.
In order for you to get the most from your investment, it is necessary for you to carefully
read and fully understand this manual.
You may also seek technical advice via the Web. Sign up for the Kangaroo Owners
CyberClub: http://www.kangaroogolf.com/welcome.htm
The Kangaroo CaddieCommand remote control system consists of three lightweight
components that easily attach to the Hillcrest or Hillcrest AB motorcaddies. It operates
on an FM Pulse Code Transmittal System that is FCC approved, and requires no operators
license. The CaddieCommand is relatively low power (milliamps) and is subject to little
outside interference.
Steerable Front Wheel Assembly 11 lbs.
Component Weight
Hand-Held Transmitter 5.5 oz.
Radio Receiver Module 1/2 lb.
Performance Specifications
Maximum Range of GO/Stop Operation........................................... 100 YARDS
Maximum Range of DIRECTIONAL Operation............................... 50 YARDS
Maximum Turning Angle of Motorcaddie.......................................... 20 Degrees
Time-Lapse from Straight Ahead to Full Turn....................................... 2 Seconds
Time-Lapse from Turn Button Release to Straight Ahead..................... 2 Seconds
Turning Radius (on Pavement)........................................................... 16 Feet
Replacement Transmitter Battery (Alkaline Battery).................................. 9 Volt
Radio Operating Frequency Range .....................................................903.37 - 921.37MHz
The Transmitter and Receiver devices comply with part 15 of FCC rules. Operation of these
devices are subject to the following two conditions:
(1) The devices may not cause harmful interference, and
(2) The devices must accept any interference received, including interference that may cause
undesired operation. FCC ID: OVPTX600-845C
OVPRX600-840C
INSTALLATION OF CaddieCommand Remote Control
Before using the CaddieCommand for the first time, follow the steps as listed below.
1. Install the CaddieCommand ON-OFF decal (stapled inside front cover).
Switch the timer to the OFF position. Grasp the knob and lift it straight off
the timer stem. It should slide off without much resistance. Peel the new
decal from the solid white paper backing. Carefully place it over the timer
stem. Align the decal with the sides of the exisiting timer decal and press it
into place. Remove the white see-through protective paper from the decal.
Replace the timer knob by aligning the white reference mark at the OFF
position. Gently press it back on the stem until it stops. NOTE: The
timer reference marks are now displayed on the outer edge of the decal.
2. On Hillcrest motorcaddies with serial numbers prior to 57484 and Hillcrest AB
motorcaddies prior to serial number 80493, a radio frequency filter wiring
harness must be installed on the motor. The frequency filter (Ferrite Bead &
Capacitor) will enable the motorcaddie to reach maximum signal range.
If a wiring harness is needed, it and detailed instructions are included with
the CaddieCommand. Motorcaddies manufactured after the above serial
numbers already have the filter installed.
3. The antenna is permanently mounted inside the receiver to make it more water
resistant. You should not attempt to open the CaddieCommand receiver—doing
so will break the seal and void the warranty.
A, B, C, D, E, F, G, H
Each CaddieCommand remote system is built using one of eight frequencies,
licensed by the FCC for the Kangaroo CaddieCommand. The frequencies are
lettered A, B, C, D, E, F, G & H. They are identified on the top corner of each
receiver module. Each frequency utilizes dozens of individual codes to operate
the CaddieCommand.
It is possible for two CaddieCommand units, of the same frequency (A-H)
operating in close proximity, to affect each other. This does NOT mean that one
operator will be able to control the other CaddieCommand, but, if both players
give their caddies signals at the same time, the signals will counteract. Neither
of the units will respond to any signal. However, if one operator is much closer
to his own caddie, it is probable that his unit would respond to the signal and not
affect the other.
To operate the CaddieCommand interference-free, we recommend a different
frequency for each CaddieCommand in your group. To avoid problems, please
advise Kangaroo Products of frequencies in use in your group when placing
an order.
No changes or modification not expressly approved by Kangaroo Products
Company can void the user’s authority to operate this device.
-2-
Once the CaddieCommand has been assembled to your
motorcaddie, the front wheel must be centered, so the unit will
track straight. Turn the SPEED to the slowest position and turn
ON both the CaddieCommand (distance timer) and the power
switch. Locate the knob on the rear of the receiver module.
(See illustration)
Use this knob to adjust the front wheel. Do not attempt to turn
the front wheel by hand. The front wheel must be centered
with the electronics. The knob is very sensitive. Rotate it
slowly to adjust the front wheel right or left as needed. (The
white arrow on the knob is an indicator only and my not always
align exactly to center.)
Make this adjustment a normal procedure each time
you assemble the motorcaddie and CaddieCommand, and
each time the front wheel becomes misaligned.
Attaching the CaddieCommand to your Motorcaddie
The steerable front wheel assembly interchanges with the regular front wheel assembly of the Hillcrest and
Hillcrest AB motorcaddies. Simply remove the original front wheel assembly. Insert the steerable front wheel
assembly and secure it with the drawlatch. Note: Some minor adjustments to the drawlatch may be needed.
See your Hillcrest Owners Manual for Drawlatch Adjustment.
Centering the Steerable Front Wheel
Slip the receiver clip over the left rear of the battery tray (opposite side of the motor). The module
should rest on the left side rear of the chassis.
Be sure the switch is in the OFF position. Insert the
gray wired handle plug • into the female receptacle on the
short wire of the receiver module ‚. Insert the red-stripe
marked plug (long wire) into the female receptacle on top of
the chassis ƒ.
To connect the steerable front wheel cable, insert its black
plug into the receptacle on the lower left side of the receiver
module „. Push inward on the lock ring while twisting it
clockwise—until it stops. Caution: Do not force the locking
ring. It will turn easily; forcing it will cause breakage.
When the ring stops turning, the plug is locked in position.
There should be approximately 1/8 to 1/16 inch of space
between the plug lock ring and the threads on the receptacle.
-3-
Connecting your CaddieCommand
Centering
Knob
OPERATING FEATURES
Automatic Self-Centering Front Wheel
The CaddieCommand’s built-in centering control will automatically center the
front wheel every time you stop transmitting a directional signal with the hand-held
transmitter. The self-centering function will not work properly unless you center
the front wheel USING THE ELECTRONICS CENTERING KNOB ( as shown
on page 3 ). If the CaddieCommand is not centered, the motorcaddie will not track straight.
During normal operation, a sensor in the CaddieCommand is detecting course
conditions and allowing for small terrain deviations, thus allowing the caddie to follow
a straight line of travel. If for any reason the front wheel becomes jammed and cannot
return to center, the self-centering feature will shutoff after 6 seconds. To dislodge the
obstacle, turn the power OFF and remove the obstruction. Turn the power back ON.
The wheel should now automatically align itself. If it does not, re-adjust the Centering
Knob as shown on page 3.
The centering and directional control in the front wheel can be damaged if the unit rams
into any obstacle. When the motorcaddie must be maneuvered in close areas, it may be
best to do so manually; for instance, across bridges, around trees or in parking lots. Dam-
age caused by hitting obstacles is not covered under the manufacturers warranty. All
CaddieCommand units MUST be returned to Kangaroo for proper repair.
There are no user serviceable components inside.
(An optional front wheel “Bumper Guard” is available to protect the unit’s centering
components.)
Electronics (Transmitter & Receiver)
Receiver Module
The receiver module is the main control center of the CaddieCommand. It processes
and relays all of the signals from the transmitter to the front wheel. The receiver module
is designed to receive a signal from the transmitter every 30 seconds. If for any
reason the unit does not receive a signal within this time span, it will shut off. The auto
shut-off will also stop the motorcaddie if it gets out of signal range. This is a required
safety function to prevent a runaway motorcaddie. In normal use, most golfers will be
making many directional adjustment signal transmissions. However, if periodic steering
adjustment is not needed, and the motorcaddie stops, just press the GO button and the unit
will start.
Hand-Held Transmitter
The transmitter is supplied with a fresh, standard Alkaline 9 volt battery. The battery
compartment is located on the bottom rear of the transmitter. The cover slides off for easy
battery replacement. Under normal use, the 9 volt battery should last 3 months. Replace
the transmitter battery at least every six months.
-4-
KEEP THEM DRY
Use great care in operating the motorcaddie around water. The transmitter
is sealed to be water resistant. However, if dropped into a puddle, pond, or
creek, it may become damaged.
The receiver module should be protected at all times against water damage.
If the caddie runs into a body of water and the receiver module becomes submerged,
the electronic circuit board inside will be destroyed. When washing the unit,
always remove the receiver module. If the CaddieCommand electronics are damaged
by extreme exposure to water, ie. submerged in a pond, the damage will not be
covered under the manufacturer’s warranty.
The Red Light located on the top front of the transmitter, labeled “9v Battery”,
signals the user in two ways.
1. When a signal is given; the light will flash twice — once with the
pressing of the button, and again when the button is released.
NOTE: The buttons are easy to press. There is no need for
excessive force. When the indicator light flashes, the signal
has been sent.
2. When the 9 volt battery is weak; the light will stay on continuously,
indicating the 9 volt battery MUST be replaced. The CaddieCommand
may have a loss of signal strength and a loss of range when the battery
is weak. To test the battery, press and hold any function button. If the
light stays on while the button is depressed, the battery is weak and
should be replaced.
The position of the transmitter is
important during signal transmission.
In order to achieve maximum range,
hold the transmitter with the control
buttons on top and the back of the
transmitter toward the ground. Point
the front of the transmitter toward the
motorcaddie. The transmitter will operate
if held otherwise, but the overall operating
range will be decreased. The range will
also be affected if there are obstacles
between you and the motorcaddie such
as trees, buildings, cars, etc.
Reminder :
The arrows indicate steering direction as
if you were operating the caddie manually. If
the caddie is coming toward you, the steering
direction of the arrows must be reversed.
CaddieCommand
9V Battery
by Kangaroo
ð
ðð
ð
ð
ðð
ð
LED
indicator light
Stop
Left
Turn Right
Turn
Go
9 volt Alkaline
battery Bottom
REAR Compartment
Front of
Transmitter
-5-
OPERATION
Connect the CaddieCommand to your Hillcrest or Hillcrest AB as instructed on page 3.
Familiarize yourself with the controls on the hand-held transmitter on page 4
and page 5.
To operate the motorcaddie in the remote mode, turn ON the distance timer. Turn the
power switch ON. The hand-held transmitter is now controlling the motorcaddie.
NOTE: When using the CaddieCommand, the distance timer
becomes an ON/OFF switch for the remote system, and will
not function as a normal distance timer.
Set the Speed Control Thumb Wheel on the Hillcrest handle to match your walking pace. To
start the motorcaddie, PRESS GO button on transmitter. Hillcrest will start and ramp up to your
preset speed. PRESS GO button a second time and the Hillcrest will automatically increase and ramp
up to 90% of its maximum speed (approximately 4.5 mph). PRESS GO button a third time and the
Hillcrest will automatically decrease its speed to your original preset speed. PRESS GO a fourth time
and it will increase and so on. . . every alternate activation of the GO button will increase or decrease
motorcaddie speed.
To start the motorcaddie, PRESS GO. To steer, PRESS AND HOLD the appropriate
Arrow Button. Once the turn is achieved, release the button and in two seconds the
front wheel will automatically return to center. NOTE: The directional buttons will
operate when the motorcaddie is stopped.
To stop the motorcaddie, PRESS STOP. (Pressing the stop button on the transmitter
DOES NOT activate the Hillcrest AB’s maximum braking system for motorcaddies with
serial numbers below 87737. To achieve maximum braking the power switch must be
turned OFF manually). If you stop the motorcaddie on a hill, always turn it across the
slope to park it. Kangaroo Motorcaddies DO NOT have a parking brake and will creep
down a hill on their own.
Hillcrest AB’s with a serial # 87737 or higher are fitted with an electronic control board that
activates Automatic Braking (AB) with CaddieCommand when the STOP button is pushed.
To stop the motorcaddie, PRESS STOP. If you stop the motorcaddie on a steep hill, you may
need to turn it across the slope to park it. Kangaroo motorcaddies DO NOT have a parking
brake and may creep down a hill on their own.
Play it Safe
Expect an orientation period to learn the controls of the CaddieCommand. Do
not try to learn the controls in close quarters. Never try to operate the
motorcaddie while it is out of your sight! Play it safe! Your new Kangaroo
is not a toy. Always use common sense while operating.
Manual Operation
To operate the motorcaddie in the manual mode, PRESS the transmitter’s STOP
button. Turn OFF the handle’s power switch and distance timer. Adjust the speed
control and turn ON the power switch.
-6-
BEHAVIOR BY MODEL COMPARISON
Hillcrest Hillcrest AB
1. Use extreme caution when operating the
regular Hillcrest on hilly courses under
remote control. The regular Hillcrest
does not slow itself going down hills,
so avoid steep hills when under
remote control. To go down steep
hills, turn the CaddieCommand OFF
at timer switch and walk with the
caddie under manual control.
2. The regular Hillcrest can track straight
nicely when traveling across a slope.
It will have a slight tendency to steer
downhill, typical of any wheeled device.
3. When attempting a turn, the regular
Hillcrest will be less responsive as it
tries to drive straight ahead due to the
equal drive force from both rear wheels.
4. The regular Hillcrest will not turn sharply
since both rear wheels try to drive
forward equally.
5. When stopping on a hillside, park the
caddie crosswise to prevent rolling.
There is no parking brake.
1. The Hillcrest AB (with AutoBrake) can
travel down hills under greater control
because of its “in gear” braking. When
the STOP button on the transmitter is
depressed, some braking is achieved.
This is equivalent to walking with the
caddie with the speed control at its
slowest position. To achieve maximum
braking, the main power switch on the
handle must be switched OFF!
1a. For serial number 87737 and higher, full
remote autobraking: see reverse page.
2. The Hillcrest AB will steer itself downhill
more readily when it is traveling across
a slope than the regular Hillcrest. This
tendency is due to the independence of
the rear wheels allowed by the differential
gearbox. It may be necessary to steer the
Hillcrest AB manually on side hills to
achieve the desired course of travel.
3. The Hillcrest AB gives prompt response to
steering input. If the caddie/golf bag set-up
is particularly rear weight biased, it is
possible that there could be some delay or
resistance to turning. Damp grass can
heighten this condition.
4. The Hillcrest AB can execute sharper turns
because of the variable drive to the wheels
via the differential gearbox.
5. When stopping on a hillside, park the caddie
crosswise to prevent rolling. There is no
parking brake.
CaddieCommand Transmitter Holster
1) Loop over belt &
secure with Velcro 2) Slip over waistband
(Long flap tucks in)
Shoot Straight . . .
while your holster accommodates your CaddieCommand Transmitter.
Kangaroo is pleased to provide a transmitter holster free of charge, with your purchase
of a new CaddieCommand radio-control system. It can be worn two ways:
1) Looped over a belt with the back flap secured by the Velcro. Or
2) Slipped over the waistband of pants or a skirt.
Try it both ways, to decide which you prefer! Its long back flap is stiff enough to hold
the unit secure. When you put your transmitter away, flip the long flap forward, secure
with Velcro, and store in a safe, dry place.
We’re sure you’re going to enjoy many fun rounds with your new CaddieCommand! Be
sure to study the Owners Manual—and to replace the transmitter’s battery every 3 months!
Manufacturer's Limited Warranty
Kangaroo Products Co.
Your Kangaroo CaddieCommand is manufactured to rigorously upheld
specifications necessary for this type of product in order to provide
dependable service to the golfer. It incorporates years of research
and development involving construction and evaluation of
countless prototypes.
The CaddieCommand is guaranteed to the original purchaser against
defective materials and workmanship for a period of one year from
the date of purchase, providing a signed and dated WARRANTY CARD
is sent to KANGAROO PRODUCTS CO. within 30 days of the date
of purchase.
The company will repair or replace, at its option, free of charge, any
CaddieCommand or part thereof found to be defective when returned
to the factory for inspection (shipping charges are the responsibility
of the customer.) Written confirmation or request for repairs or
replacements must accompany all merchandise.
IMPORTANT: Damage or failure due to accident, abuse, misuse or
neglect is specifically excluded under this warranty.
This guarantee is in lieu of all other guarantees, expressed or implied,
and we cannot authorize any person to assume for us any other obligation
or liability in connection with the sale of this product.
Features and manufacturer’s specifications are subject to change without notice.
This product is manufactured for the sole purpose of remotely controlling a
Kangaroo Hillcrest motorcaddie during a game of golf. Other use voids
the warranty and releases manufacturer and its sales agents from liability.
Do not attempt to repair, alter, or modify any CaddieCommand Remote
Control System or component thereof without prior authorization from
Kangaroo’s Technical Service Department. Failure to comply
automatically voids the manufacturer’s warranty!