Keeson Technology MC142 CONTROL BOX User Manual MC142
Keeson Technology Corporation Limited CONTROL BOX MC142
User Manual
Issue department:Bedding Division ProductFunction instruction 2018-03-26 Kyle Date: Author: No: Version: 1.1 Page 1 of 3 MC142 MC142Function instruction 1. Electrical configuration diagram: FCC: 2AK23RF358B IC: 22406-RF358B Massage Unit part number 68000024 Massage Motor Splitter Cable 68000221 USB Charger USB 68000089 Power Outlet USB/110V 68000838 WIFI 68001404 Bettery backup 68000221 Power Supply 68000289 FCC ID: 2AK23MC142 IC: 22406-MC142 Power Cord AC 68001449 Head Motor 68001380 Lumbar 68001402 68000220 Input Cable DC 2. Function Picture 3. Process of test 3.1. HEAD port Connect to head actuator,control by remote single: Click head up button on the remote, head actuator moves out, stop when released; Click headdown button,head actuator moves in, stop when released; This function takes effect only by pressing the corresponding button on the remote. Foot Motor 68001381 Issue department:Bedding Division ProductFunction instruction Date: Author: 2018-03-26 Kyle No: Version: 1.1 Page 2 of 3 MC142 3.2. FOOTport Connect to foot actuator,control by remote single: Click foot up button,foot actuator moves out,stop when released; Click foot down button,foot actuator moves in,stop when released; This function takes effect only by pressing the corresponding button on the remote. 3.3. Massage Connect to head massage,control by remote: Click head massage + button,head massage strengthens by one level; Click head massage ‐ button,head massage weakenby one level; This function takes effect only by pressing the corresponding button on the remote. 3.4. MULTIFUNCTION port Connect with the same other Control box or Other accessories; 3.5. Power LED& PAIRING LED Power supply for control box, PAIRINGLED of control box flashes for 4 times,and then turns off, POWER LED turns on。 3.6. Power Connect to the 29V DC; 3.7. Pair Function Power up control box,pairing LED will be flash,the control box enters into mode of code paring; Press and hold the paring LED of Remote, the backlight of paring LED flashes, the backlight of remote flashes, the remote enters into mode of code paring; The backlight of paring LED of remote stops flashing, and the paring led of control box stop flash, it indicates that the code paring is successful; If fails, repeat all the processes above; Issue department:Bedding Division ProductFunction instruction 2018-03-26 Kyle Date: Author: No: Version: 1.1 Page 3 of 3 MC142 3.8. FLAT function Press and release the FLAT buttonon remote,the head and foot actuators moves to lower position(when the actuator is free, can turn off the vibration motor and turn off the indicator light when press once ),stop when press any buton; This function takes effect only by pressing the corresponding button on the remote. 3.9. ZERO G position function Press and release ZERO G button on remote,the head and foot actuator moves to preset memory position,stop when press any button; This function takes effect only by pressing the corresponding button on the remote. FCC: Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. ISED RSS Warning: This device complies with Innovation,Science and Economic Development Canada licenceexempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'ISED applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. ISED RF exposure statement: This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator& your body.This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Le rayonnement de la classe b repecte ISED fixaient un environnement non contrôlés.Installation et mise en œuvre de ce matériel devrait avec échangeur distance minimale entre 20 cm ton corps.Lanceurs ou ne peuvent pas coexister cette antenne ou capteurs avec d’autres.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No Author : baclsh51 Create Date : 2018:11:26 13:59:30+08:00 Modify Date : 2018:12:17 14:10:08-08:00 Has XFA : No XMP Toolkit : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26 Format : application/pdf Creator : baclsh51 Title : Microsoft Word - MC142_User Manual Creator Tool : PScript5.dll Version 5.2.2 Metadata Date : 2018:12:17 14:10:08-08:00 Producer : Acrobat Distiller 11.0 (Windows) Document ID : uuid:9a303add-6104-4985-95ac-9942cd63fb02 Instance ID : uuid:374ce1a8-fb47-4c4f-8218-463735fc2080 Page Count : 3EXIF Metadata provided by EXIF.tools