Kenmore 1758579280 User Manual HOME CLEANING SYSTEM Manuals And Guides L0812147
KENMORE Vacuum, Built in Manual L0812147 KENMORE Vacuum, Built in Owner's Manual, KENMORE Vacuum, Built in installation guides
User Manual: Kenmore 1758579280 1758579280 KENMORE HOME CLEANING SYSTEM - Manuals and Guides View the owners manual for your KENMORE HOME CLEANING SYSTEM #1758579280. Home:Vacuums & Floor Care Parts:Kenmore Parts:Kenmore HOME CLEANING SYSTEM Manual
Open the PDF directly: View PDF 
.
Page Count: 16
| Download | |
| Open PDF In Browser | View PDF |
SEARS OWNERS MANUAL HOME CLEANING SYSTEM MODEL NO. 175.8579280 CAUTION: Read Instructions and Rules for Safe Operation Carefully For household use only. Save this Manual for Future Reference SEARS, 5553282 (1289) ROEBUCK AND CO., nnlolP HOME CLEANING SYSTEM . • • , • INTRODUCTION ASSEMBLY OPERATION MAINTENANCE REPAIR PARTS Dept. 698/731A, Sears Tower, Chicaqo, IL 60684 PRINTED IN U.S.A. IMPORTANT SAFETY iNSTRUCTiONS--Readallinstructionsbeforeusingthi When using any electrical appliance, basic precautions should always be followed, including the following: WARNING electric -To reduce the risk of fire, shock, or injury: 1. Do not leave cleaner when plugged into electrical outlet. Unplug from outlet when not in use and before servicing. 2. WARNING: TO AVOID ELECTRIC SHOCK, DO NOT EXPOSE TO RAIN n STORE INDOORS. 3. WARNING: DO NOT REMOVE GROUNDING PRONG FROM POWER CORD PLUG. Connect to a properly grounded outlet ONLY. See Grounding Instructions. GROUNDING INSTRUCTIONS: Thisvacuumcleanermustbegrounded.Ifitshouldmalfunction or raryadaptershouldbeusedonlyuntila properlygroundedoutlet(see break down,groundingprovidesa path of least resistancefor figure A) can be installed by a qualified electrician.The tab for electricalcurrenttoreducetheriskofelectricshock.Thisvacuum groundingscrew(seefigure B) extendingfrom theadaptermustbe cleanerisequippedwith a cordhavingan equipment-greundingconnectedto a permanentgroundsuchasa properlygroundedoutlet boxcover.Wheneverthe adapteris in use, it mustbe held in place conductorandgroundingplug.The plugmustbe pluggedintoan appropriate outletthatis properlyinstalled and groundedinaccor- by a metalscrew(see FigureB). dancewithalllocalcodesandordinances. ADAPTER WARNING:Improperconnectionof theequipment-grounding conductor canresultin a risk ofelectric shock.Checkwith a qualified electricianor servicepersonif you are in doubtas to whetherthe outlet isproperly grounded.DONOT modifythe plugprovidedwith the vacuumcleaner-- if it willnotfit theoutlet,havea properoutlet installed bya qualifiedelectrician. This vacuumcleaneris for useon a nominal120 -voltcircuit,and hasa groundedplug(seefigureA).A temporaryadapter(seefigure B) may be used to connectthis plug to a 2-pole receptacle(see figure B) ifa properlygroundedoutlet is not available.Thetempo4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. o GROUNDED PLUG t GROUNDED 2-POLE OUTLET GROUNDING SCREW RECEPTACLE Fiqure A Fiqure B DISCONNECT POWER CORD FROM ELECTRICAL OUTLET before the recovery tank is emptied, the solution tank is refilled, or the cleaner is serviced in any way. DO NOT store this cleaner in an area which may reach freezing temperatures. Should this occur, DO NOT operate this cleaner until it has been at room temperature for at least two (2) hours. DO NOT use any cleaning solution or chemicals other than those discussed in this manual. For maximum efficiency, empty container frequently and keep inside of hose, wands, nozzle and container clean. DO NOT overwet carpet or unholstery. If three or more cleaning strokes are required, let the carpet or upholstery material dry and then repeat cleaning process. Do not allow children to operate cleaner, nor should they play with cleaner as a toy. Close attention is necessary when used around or near children. Use this cleaner ONLY for its intended use as described in this manual. Use only the attachments recommended in this manual. Always turn cleaner OFF when connecting or disconnecting the Spraymate motorized nozzle. Do not use with damaged cord or plug. If cleaner is not working properly, has been dropped, damaged, left outdoors, or dropped into water, return it to a Sears Service Center. Do not pull or carry by cord, nor use cord as a handle, nor close a door on cord, nor pull cord around sharp edges or corners. Do not run cleaner over cord. Keep away from heated surfaces. Do not unplug from electrical outlet by pulling on the cord. To unplug, grasp the plug, not the cord, and pull. Do not handle plug or cleaner with wet hands. Do not put any objects in ventilation openings. Do not use with any opening blocked; keep openings free of dust, lint, hair, and anything that may reduce air flow. Keep hair, loose clothing, fingers, and all parts of the body away from openings and moving parts. NEVER vacuum materials such as hot coals, cigarette butts, matches, etc. When "dry" vacuuming do not use without filter in place. Turn off all controls before unplugging. Use extra care when using on stairs. Do not use to pick up flamable or combustible liquids such as gasoline or use in areas where such liquids may be .present. m SAVE THESE iNSTRUCTiONS Page 2 TABLE OF CONTENTS Warranty ............................ .......................................... page 3 Safety Instructions ....................................................... page 2 Introduction .................................................................. page 3 Assembly ..................................................................... page 4 Operation .................................................................. page 5-8 Additional Uses / Optional Accessories .................... page 8-9 Trouble Shooting Chart .............................................. page 10 Exploded Views and Parts Lists .......................... page 11-15 Ordering Parts ............................................................ page 16 FULL ONE YEAR WARRANTY When used for private household purposes, if within one year from the date of purchase, this vacuum cleaner fails due to a defect in material or workmanship, RETURN IT TO THE NEAREST SEARS SERVICE CENTER/DEPARTMENT IN THE UNITED STATES, and Sears will repair it, free of charge. If this vacuum cleaner is used for commercial or rental purposes, the above warranty coverage applies for only 90 days from the date of purchase. This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state. SEARS, ROEBUCK AND CO., D/731CR-W, SEARS TOWER, CHICAGO, IL 60684 INTRODUCTION Your new Kenmore Home Cleaning System isa deluxe high performance cleaner, designed for today's cleaning requirements. With proper care and maintenance, it should provide you with years of service. It is important that you read this manual to fully understand the cleaner's capabilities as well as providing you with the essentials regarding maintenance and safety. A complete list of operating parts and features is shown in figure 1 below. ANGLED WAND RECOVERY TANK POWER HEAD 2 SPEED PUMP SWITCH STEEL WANDS HOSE SOLUTION SOLUTION TUBING FLOOR NOZZL Fig. 1 Page 3 ASS LY ASSEMBLY OF RECOVERY TANK AND SOLUTION TANK POWER POWER HEAD See Figure 2 1. Place Recovery Tank into Solution Tank (align the word "VACUUM" on Recovery Tank with "VACUUM" on Solution Tank)and secure with Metal Latch. 2. Unwind Power Cord from the Power Head. 3. Insert the plug on the Short Cord from the Solution Tank into the Recovery Tank Power Head. SHORT CORDIN HERE RECOVERY METAL ASSEMBLY OF HOSE, WANDS, NOZZLE AND SOLUTION TUBING SHORT See Figure 3 1. Assemble the two Straight Wands. 2. Assemble the upper Straight Wand to the Angled Wand of the Hose. 3. Assemble the Floor Nozzle to the lower Straight Wand. SOLUTION NOTE: Be sure locking button engages properly when assembling straight wands, angled wand, and floor nozzle. Fig. 2 See DETAIL "A"- Figure 3. 4. Thread Solution Tube Nut onto threads of the Trigger Valve. 5. Snap Solution Wands. Tubing onto Retaining Clips DETAIL "A" on the See DETAIL "B'- Figure 3. 6. Attach the Vacuum Hose to Recovery Tank inlet (Vacuum Inlet). 7. Insert the Plastic Insert of the Solution Tubing into the Coupling of the Solution Tank. TRIGGER VALVE SOLUTION TUBE NUT 3 CLIP NOTE: To remove the Plastic Insert depress the Tab and gently pull on the Plastic Insert. Be careful to pull on the Plastic Insert and not the Tubing as da.mage may occur. PLASTIC INSERT- VACUUM _ COUPLING Fig. 3 DETAIL "B" Page 4 HOSE P CARPET O PREPARATION For best results prepare carpet for cleaning as follows: 1. Vacuum carpet to remove loose dirt before using Cleaner. 2. To remove stains and ground in dirt present in heavy traffic areas of the carpet, spray or rub Sears Heavy Traffic PreTreatment (82833) into carpet before using Cleaner. Follow directions on the bottle. FILLING CLEANER FILLER OPENING WITH WATER AND CLEANING SOLUTION See Figure 4 JTION TANK 1. Open lid of the Filler Opening. 2. Add Sears All In One Carpet Cleaner (82813) solution or Sears Upholstery Cleaner (82843) solution to Solution Tank (depending on type of cleaning to be performed). Follow directions on label of bottle. 3. Pour clean, hot water (from tap) into Filler Opening in the Solution Tank -- use two (2) gallons of water. 4. Close Filler Opening. Fig. 4 NOTE: This unit may become damaged if boiling water is used. PUMP SWI POWER CORD AND SWITCH See Figure 5 1. Unwrap Power Cord from around Power Head and plug into electrical outlet. 2. Turn Power Switch to "ON" position. POWER SWITCH POWER CORD PUMP SWITCH See Figure 5 1. Place Pump Switch from "OFF" position to either "HI" or "LO" position. NOTE: "HI" pump speed is used for normal cleaning. "LO" pump speed is used for delicate upholstery or light cleaning. Fig. 5 --Continued-- Page 5 OP RATIO TEST FOR SOLUTION SPRAY See Figure 6 1. Hold Floor Nozzle above floor level. 2. Pull Solution Release Trigger on Angled Wand. 3. Obsewe Floor Nozzle to make sure cleaning solution is being sprayed evenly from two points. (see DETAIL "A" ) RELEASE TRIGGER NOTE: If solution is not being sprayed from both points, refer to Trouble Shooting Chart. _PRAYS OF SOLUTION / DETAIL Fig. 6 SLOWLY PULL TOWARDS YOU CLEANING THE CARPET See Figures 7 & 8 Solution Dispensing Stroke: 1. Start at a corner (recommended). 2. Place Floor Nozzle so Suction Inlets are flush with carpet. 3. While exerting light pressure down on Floor Nozzle, depress Solution Release trigger and slowly pull Floor Nozzle towards you. NOTE: Do not ovenNet. If three or more cleaning strokes are required, let dry and then repeat cleaning process. SUCTION INLETS Fig. 7 LIFT, SET FORWARD, PULL BACK ACROSS CARPET Solution Recovery Stroke: 1. Release Solution Release Trigger. 2. Lift Floor Nozzle off carpet. 3. Return Floor Nozzle to point where you dispensed cleaning solution and pull across carpet, recovering dirty solution. I Fig. 8 Page 6 OP ATIO WHEN TO EMPTY RECOVERY TANK See Figure 9 During normal operation, your cleaner may stop recovering solution from your carpet. When this occurs there are three check points to alert you: 1. An increase in motor noise. 2. No solution visibly being recovered by the floor nozzle. 3. No air coming from the exhaust port of your cleaner. EXHAUST PORT RECOVERY TANK When this occurs: 1. The Recovery Tank is full and the Float Valve in the Recovery Tank has been activated. The Recovery Tank should be emptied. or w 2. The Recovery Tank has foam in the Tank and the Float Valve has been activated. NOTE: If cleaner is accidently turned over while in operation, the float may activate and shut off the suction. If this occurs, set the cleaner upright. Turn Power Switch "OFF" and let motor come to a complete stop. Then turn switch back on and continue cleaning. Fig. 9 METAL _CK BUTTON ,ATOH VA o TA_ TUBING DETAIL "A" TO EMPTY RECOVERY TANK See Figure 10 RECOVERY 1. Turn Power Switch "OFF" and Disconnect Power Cord from Electrical Outlet, 2. Disconnect Short Cord located between Solution Tank and Recovery Tank. 3. Disconnect Vacuum Hose by depressing the Lock Button and remove. 4. Push Tab inward on Plastic Coupling and remove Plastic Insert and Tubing. (See DETAIL "A" ) 5. Lift Latches on Power Head. 6. Lift power Head, by Handle, and remove from Recovery Tank. 7. Rotate Metal Latch on the Solution Tank and lift Recovery Tank from the Solution Tank. HEAD TANK_ HANDLE S CORD LATCH 8. Empty Recovery Tank. 9. Reassemble cleaner and resume cleaning. Fig. 10 Page 7 SOLUTION TANK OPERATION TO, EMPTY THE SOLUTION TANK METHOD 1 See Figure 11 When cleaning is completed, both the Recovery Tank and the Solution Tank should be emptied prior to storage. Empty the Recovery Tank as described earlier. There are three methods of emptying the Solution Tank. Method 1 : 1. Disconnect Pump Cord from Recovery Tank. 2. Remove Recovery Tank from Solution Tank and pour solution out of the Filler Opening. Method 2" 1. Place Floor Nozzle in bath tub or container. 2. Depress Solution Release Trigger and spray until empty. Method 3: 1. Remove Floor Nozzle and insert Wand into Solution Tank through the Filler Opening. 2. Vacuum solution out. METHOD 3 METHOD 2 Fig. 11 3. All solution is now in Recovery Tank. Empty Recovery Tank as described earlier. ADDITIONAL U "DRY" VACUUMING See Figure 12 KEY PART NO. DESCRIPTION 1 2 3 643076-008 642458-004 660408-001 Floor/Rug Nozzle 10" Squeegee Cloth Filter Assembly Included with your cleaner are accessories to convert your cleaner to perform dry vacuum cleaning. 1. Insert the Cloth Filter into the Recovery Tank. 2. Use the Floor/Rug Nozzle or the Squeegee Nozzle as desired. Fi#. 12 NOTE: You MUST use the Cloth Filter when "dry" cleaning. EXHAUST PORT NOTE: Squeegee Nozzle is also useful in "pick up" operation of "wet" cleaning. USE AS A BLOWER See Figure 13 1. Insert Hose into the Exhaust Port of the Power Head. 2. Turn Power Switch "ON" and direct hose to area to be blown. Fig. 13 Page 8 OPTIO AL CLEAN ACCESSORIES Optional cleaning accessories may be purchased or ordered through your nearest Sears store. A complete set of instructions comes with each attachment set. UPHOLSTERY NOZZLE Model No. =081452 See Figure 14 The KenmoreUpholstery Nozzle is an optional attachment for furniture upholstery cleaning. The upholstery nozzle may also be used to clean auto upholstery or carpeting. In addition, the nozzle may also be used to clean carpeted stairs and other areas difficult to clean with the normal floor nozzle. Fig. 14 KENMORE SPRAYMATE POWER NOZZLE Model No. =°81252 See Figure 15 The Kenmore Spraymate is an optional attachment for carpet cleaning. The Spraymate has a motorized beater brush which is especially good to scrub difficult to clean areas of heavy traffic. Fig.15 Page 9 T OU LE SHOOTI PROBLEM 1. Neither vacuum motor runs. POSSIBLE G CHART SOLUTIONS* motor nor pump 1. Be sure power switch is in "ON" position. 2. Be sure power cord is plugged in securely. 3. Check wall electrical outlet (by plugging in a known working electrical appliance). 2. Vacuum motor runs, but there is no spray at the nozzle. 1. Be sure Electrical Cord from Power Head to Solution Tank is securely plugged into receptacle on the Power Head. 2. Check that Solution Tank is full. 3. Be sure Pump Switch is in the "HI" or "LO" position. 4. Nozzle Ports may be clogged. See illustration below to unclog. . Spray from the floor nozzle comes out of one side of the nozzle only. 1. Unclog the Nozzle Port. See illustration below. . Motor runs but cleanerdoes not pick up solution from carpet (no exhaust from top of cleaner). o Recovery Tank is full of dirty water and must be emptied. 2. Check for clogged hose or nozzle. Clogs could result from picking up material such as carpet strings, shoe laces, etc. 5. Spray connections leak. o Disassemble nut at leaking connection. Be sure washer is properly seated. Reassemble and tighten securely. * If the "Possible Solutions" to "Problems" listed in the chart do not correct the problem, take your cleaner to a Sears Service Center for professional serice. Repairs not listed in this chart require professional and specific knowledge of this model cleaner and could result in safety hazards and personal injury if not made by a qualified Sears Service Technician. TO UNCLOG NOZZLE PORT ACCESS SCREWS See Figure 16. 1. Remove Access Screws 2. Clean out ports (2) with a small pin. 3. Reassemble. SMALL PIN NOTE: Do not let pin point touch any part of the spray pad surface or spray pad will not spray solution properly. SPRAY PAD SURFACE SPRAY PAD SURFACE Fig. 16 Page 10 SEARS HOME CLEANING SYSTEM --MODEL 175.8579280 ! SEE PAGE 14 FOR EXPLODED VIEW SEE PAGE 12 FOR EXPLODED VIEW Page 11 SEARS HOME CLEANING SYSTEM -- MODEL 175.8579280 46 6 9 33 Page 12 SEARS HOME CLEANING SYSTEM -- MODEL 175.8579280 KEY 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 PART NO. 644147-003 642337-002 642338-042 642315-011 641798-003 643492-005 642149-001 643509-001 641843-013 642367-006 644548-004 642367-004 643909-902 642367-004 642406-019 641857-010 641866-036 642409-002 643584-000 642405-001 643579-002 642313-000 642713-001 642447-000 642409-002 644846-001 642470-006 640218-005 706382-319 642339-049 644773-010 640145-005 643565-013 643561-000 644802-001 642392-003 643562-005 643535-001 643438-005 643536-000 643566-013 643531-007 643533-002 888493-304 643685-001 642046-014 989629-002 660081-002 640940-001 643431-008 643454-003 643583-000 DESCRIPTION Handle Plate Handle Screws (2) Handle Shroud w/Label Switch Cap Motor Housing Screws (2) Female Pigtail Wiring Nut Switch Power Cord Motor Seal Motor Cover Motor Seal Carbon Brush Asm. Motor Seal Motor Asm. Complete Latch (2) Cover Asm. w/# 19, 20, 21,22 Cover Screws (4) Foam Filter Valve Asm. w/#21,22 Valve Screws (2) Sensor Guard Pump Switch Cap Baffle Baffle Screws (2) Two Speed Switch - Pump w/Swithch Cap Rivet Wave Washer Washer (2) Separator Plate w/Key #8 Coupling Body Separator Plate Screws (2) Upper Container w/Filler Door Retaining Ring Ground Lead Screw Lead w/terminal Tubing Asm. w/#39, 34 Valve Seat Screws (2) Valve Seat Gasket Lower Container Pigtail Lower Container Screws (3) Strain Relief Motor Screws (2) Dirt Container w/Baffle and Screws Latch Screw Latch Spacer Filler Door Washers (3) Foam Filter 53 54 55 56 643685-001 661393-001 643171-003 644089-012 Motor Screws (4) Casters (3) "O" Ring Gasket Pump Motor Page 13 SEARS HOME CLEANING SYSTEM -- MODEL 175,8579280 16 22 21 20 19 18 15 14 17 12 "_=---10 _28 Page 14 13 SEARS HOME CLEANING KEY 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 SYSTEM -- PART NO. 644153-008 644152-004 644037-003 644156-005 643731-007 644038-003 644773-005 644773-009 644157-005 643570-019 644163-007 644037-003 644038-001 643572-006 644162-003 643446-000 643171-002 644151-003 643444-000 643445-000 643171-002 644830-003 643186-018 644037-003 640145-007 643454-002 643526-002 643571-009 660850-172 MODEL 175.8579280 DESCRIPTION Angled Wand Trigger Ferrule Nut Swivel Connector 1 - 1/4" dia. Tubing Strap Tubing - Hose Coupling Insert Nut Coupling Insert Swivel Connector 2 - 1/2 "dia. Hose and Angled Wand Asm. 8' Hose Ferrule Nut Tubing - to Nozzle Valve Asm. Kit w/trigger Nut Neoprene Washer "O" Ring Sleeve Sprirlg Valve Washer - Stainless Steel "O" Ring Lock Button Straight Wands (2) Ferrule Nut Screw (2) Neoprene Washer Screw (2) Nozzle Asm. Complete w/Key # 12,13, 15, 16 Owner's Manual Page 15 SEARS OWNERS MANUAL SERVICE MODEL NO. 175.8579280 HOW TO ORDER REPAIR PARTS K nfnor HOME CLEANING SYSTEM Now that you have purchased your Kenmore Home Cleaning System, should a need ever exist for repair parts or service, simply contact any Sears Service Center. Be sure to provide all pertinent facts when you call or visit. The model number of your Kenmore Home Cleaning System will be located under the handle. WHEN ORDERING REPAIR PARTS, THE FOLLOWING INFORMATION: ALWAYS GIVE . PART NUMBER • PART DESCRIPTION • MODEL NUMBER 175.8579280 ° NAME OF ITEM Cleanmore Home Cleaning System All parts listed may be ordered from any Sears Service Center. If the parts you need are not stocked locally, your order will be electronically transmitted to a Sears Repair Parts Distribution Center for handling. SEARS, ROEBUCK AnD CO., Dept. 698/731A, Sears Tower, Chicago, IL 60684
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : No Page Count : 16 Page Layout : SinglePage Page Mode : UseNone Producer : Goby Monitor Application version 4, 0, 0, 13 Create Date : Fri Dec 19 04:15:40 2008 Author : Title : Subject :EXIF Metadata provided by EXIF.tools