Kenmore 41516237 User Manual GAS GRILL Manuals And Guides L0703044

KENMORE Grill, Gas Manual L0703044 KENMORE Grill, Gas Owner's Manual, KENMORE Grill, Gas installation guides

User Manual: Kenmore 41516237 41516237 KENMORE GAS GRILL - Manuals and Guides View the owners manual for your KENMORE GAS GRILL #41516237. Home:Lawn & Garden Parts:Kenmore Parts:Kenmore GAS GRILL Manual

Open the PDF directly: View PDF .
Page Count: 35

Download
Open PDF In Browser	View PDF

AssemblyInstructions/Useand Care Manual

LiquidPropane GasGrill
Kenrnore Model No. 415.16237

This Grill is For
Outdoor Use Only

* Read this manual before cooking on
grill. Failure to follow all
manufacturer's
instructions could
result in fire or explosion which could
cause property damage, personal
injury or death.
* Combustion
by=products
produced
when using this product contain
chemicals known to the State of
California to cause cancer, birth
defects, or other reproductive
harm.
__

• Parts

• Use and Care

• Assembly

• Troubleshooting

• Safety Rules

• Espa5oi, p. 36

Assembly Questions?
Call 1 =800=241 =7548
* Read and follow all Safety
Statements, Assembly Instructions
and Use & Care Directions before
attempting to assemble and cook.

T
9

* Some parts may contain sharp edges,
especially as noted in these
instructions. Wear protective gloves
if necessary.

Parts Ordering:
Call 1 =800=4=MY=HOME ®

To Installer/Assembler:
Leave
these instructions with
consumer.

To Consumer: Keep this
manual for future reference.

Sears, Roebuck and Co., Hoffman Estates,
©2005Sears, RoebuckandCo., All Rights Reserved

IL 60179

U.S.A.
Printedin USA

Safety Symbols
The symbols and boxes shown below explain what each heading
means. Read and follow all of the messages found throughout
the manual.

if you smell gas:
1. Shut off gas to the appliance.
2. Extinguish any open flame.

DANGER: Indicates an imminently hazardous situation
which, if not avoided, will result in death or serious injury.

3. Open lid.
4. if odor continues, keep away from the
appliance and immediately call your gas
supplier or your fire department.

WARNING: Be alert to the possibility of serious bodily injury if
the instructions are not followed. Be sure to read and carefully
follow all of the messages.

1. Do not store or use gasoline or other
flammable liquids or vapors in the vicinity of
this or any other appliance.
2. An LP cylinder not connected for use shall not
be stored in the vicinity of this or any other
appliance.

,o.

CAUTION: Indicates a potentially hazardous situation which,
if not avoided, may result in minor or moderate injury.
Installation

Safety Precautions

• Use grill, as purchased, only with LP (propane) gas and the
regulator/valve assembly supplied.

Call Grill Service Center For Help And Parts
If you have questions or need assistance during assembly,
please call 1-800-241-7548. You will be speaking to a
representative of the grill manufacturer and not a Sears
employee. To order new parts call Sears at 1-800-4-MY-HOME®.

Product Record
IMPORTANT:Fill out the product record informationbelow.
Model Number

Serial Number
See ratinglabel on grill for serialnumber.
Date Purchased

D
__

cAuT,o.

For residential use only. Do not use for commercial
cooking,
2 " 463264407

• Grill installation must conform with local codes, or in their
absence of local codes, with either the National Fuel Gas
Code, ANSI Z223.1/NFPA 54, Natural Gas and Propane
Installation Code, CSA B149.1, or Propane Storage and
Handling Code, B149.2, as applicable.
, All electrical accessories (such as rotisserie) must be
electrically grounded in accordance with local codes, or
National Electrical Code, ANSI/NFPA 70. Keep any electrical
cords and/or fuel supply hoses away from any hot surfaces.
, Grill is not for use in or on recreational vehicles and/or boats.
, This grill is safety certified for use in the United States only. Do
not modify for use in any other location. Modification will result
in a safety hazard.

For Your Safety ......................................

Grill Service Center ...................................

Product Record Information ............................

Safety Symbols ......................................

Installation Safety Precautions ..........................

Kenmore Grill Warranty ...............................

Use and Care .....................................

4-11

Parts List ..........................................

Parts Diagram ......................................

Assembly .......................................

14-30

Cooking Table ......................................
Troubleshooting ..................................

Repair Protection

31
32-35

Agreements

Congratulations on making a smart purchase. Your new
Kenmore®product is designed and manufactured for years of
dependable operation. But like all products, it may require repair
from time to time. That's when having a Repair Protection
Agreement can save you money and aggravation.
Purchase a Repair Protection Agreement now and protect
yourself from unexpected hassle and expense.

KENMORE GRILL WARRANTY
One-Year Full Warranty on Kenmore Grill
If this grill fails due to a defect in material or workmanship
within one year from the date of purchase, call 1-800-4-MYHOME® to arrange for free repair (or replacement if repair
proves impossible).
Ten-Year Limited Warranty on Stainless Steel Burners
For ten years from the date of purchase, any stainless steel
burner that rusts through will be replaced free of charge. After
the first year from the date of purchase, you pay for labor if
you wish to have it installed.
All warranty coverage excludes ignitor batteries and grill part
paint loss, discoloration or rusting, which are either
expendable parts that can wear out from normal use within
the warranty period, or are conditions that can be the result
of normal use, accident or improper maintenance.
All warranty coverage is void if this grill is ever used for
commercial or rental purposes.
All warranty coverage applies only if this grill is used in the
United States.
This warranty gives you specific legal rights, and you may
have other rights which vary from state to state.
Sears, Roebuck and Co., Hoffman Estates, IL 60179

Here's what's included in the Agreement:
[]
[]
[]
[]

[]

Expert service by our 12,000 professional repair specialists
Unlimited service and no charge for parts and labor on all
covered repairs
Product replacement if your covered product can't be fixed
Discount of 10% from regular price of service and servicerelated parts not covered by the agreement; also, 10% off
regular price of preventive maintenance check
Fast help by phone- phone support from a Sears
technician on products requiring in-home repair, plus
convenient repair scheduling

Once you purchase the Agreement, a simple phone call is all that
it takes for you to schedule service. You can call anytime day or
night, or schedule a service appointment online.
Sears has over 12,000 professional repair specialists, who have
access to over 4.5 million quality parts and accessories. That's
the kind of professionalism you can count on to help prolong the
life of your new purchase for years to come. Purchase your
Repair Protection Agreement today!
Some limitations and exclusions apply.
For prices and additional information call 1-800-827-6655.
Sears installation Service
For Sears professional installation of home appliances, garage
door openers, water heaters, and other major home items, in the
U.S.A. call 1-800-4-MY-HOME®
463264407 • 3

LP Tank
The LP tank used with your grill must meet the following
requirements:
Use LP tanks only with these required measurements: 12"
(30.5cm) (diameter) x 18" (45.7 cm) (tall) with 20 lb. (9 kg.)
capacity maximum.
• NEVER store a spare LP tank under or near grill or in
encle

LP tanks must be constructed and marked in accordance with
specifications for LP tank of the U.S. Department of
Transportation (DOT). See LP tank collar for marking.
• LP tank valve must have:
, Type 1 outlet compatible with
regulator or grill.
, Safety relief valve.
, UL listed Overfill Protection

OPDHand Wheel
Device (OPD). This OPD safety
feature is identified by a unique triangular hand wheel. Use
only LP tanks equipped with this type of valve.

• Never fill the cylinder beyond 80% full.

. LP tank must be arranged for vapor withdrawal and include
collar to protect LP tank valve.

• An overfilled or improperly stored tank is a hazard due
to possible gas release from the safety relief valve.

LP (Liquefied Petroleum Gas)

• if you see, smell or hear escaping gas, immediately get
away from the LP tank/grill and call your fire
department.

* LP gas is nontoxic, odorless and colorless when produced. For
Your Safety, LP gas has been given an odor (similar to rotten
cabbage) so that it can be smelled.

• if the above is not followed exactly, a fire causing
death or serious injury may occur.

, LP gas is highly flammable and may ignite unexpectedly when
mixed with air.

LP Tank Filling
LP Tank Removal, Transport And Storage
, Turn OFF all control knobs and LP tank valve. Turn coupling
nut counterclockwise by hand only - do not use tools to
disconnect. Lift LP tank wire upward off of LP tank collar, then
lift LP tank up and off of support bracket, install safety cap onto
LP tank valve. Always use cap and strap supplied with valve.
Failure to use safety cap as directed may result in serious
personal injury and/or property damage.
LP Tank Valve

• LP dealer must purge tank before filling.
• Dealer should NEVER fill LP tank more than 80% of LP tank
volume. Volume of propane in tank will vary by temperature.
• A frosty regulator indicates gas overfill. Immediately close LP
tank valve and call local LP gas dealer for assistance.
, Do not release liquid propane (LP) gas into the atmosphere.
This is a hazardous practice.

Safety Cap
Retainer Strap
, A disconnected LP tank in storage or being transported must
have a safety cap installed (as shown). Do not store an LP tank
in enclosed spaces such as a carport, garage, porch, covered
patio or other building. Never leave an LP tank inside a vehicle
which may become overheated by the sun.
, Do not store an LP tank in an area where children play.
4 " 463264407

• Use only licensed and experienced dealers.

, To remove gas from LP tank, contact an LP dealer or call a
local fire department for assistance. Check the telephone
directory under "Gas Companies" for nearest certified LP
dealers.

LP Tank Exchange

Connecting

o Many retailers that sell grills offer you the option of replacing
your empty LP tank through an exchange service. Use only
those reputable exchange companies that inspect, precision fill,
test and certify their cylinders. Exchange your tank only for
an OPB safety feature-equipped tank as described in the
"LP Tank" section of this manual.

1. LP tank must be properly secured onto grill. (Refer to
assembly section.)

Always keep new and exchanged LP tanks in upright position
during use, transit or storage.

Regulator To The LP Tank

2. Turn all control knobs to the OFF position.
3. Turn LP tank OFF by turning OPD hand wheel clockwise to a
full stop.
4. Remove the protective cap from LP tank valve. Always use
cap and strap supplied with valve.

, Leak test new and exchanged LP tanks BEFORE
connecting to grill,

LP Tank Leak Test
For your safety
• Leak test must be repeated each time LP tank is exchanged or
refilled.
Do not smoke during leak test.
• Do not use an open flame to check for gas leaks.
Grill must be leak tested outdoors in a well-ventilated area,
away from ignition sources such as gas fired or electrical
appliances. During leak test, keep grill away from open flames
or sparks.
, Use a clean paintbrush and a 50/50 mild soap and water
solution. Brush soapy solution onto areas indicated by arrows
in figure below. Leaks are indicated by growing bubbles.

Do not use a POL transport plug
(plastic part with external threads)!
it will defeat the safety feature of
the valve.

If "growing" bubbles appear do not use or move the LP tank.
Contact an LP gas supplier or your fire department!

A Do not use household cleaning agents. Damage to gas
train components can result.

5. Hold regulator and insert nipple into LP
tank valve. Hand-tighten the coupling
nut, holding regulator in a straight line
with LP tank valve so as not to crossthread the connection.

Nipple has to be centered
intothe LPtank valve.

463264407 • 5

Leak Testing Valves, Hose and Regulator
1. Turnall grill control knobs to OFE
,

Be sure regulator is tightly connected to LP tank.

3. Completely open LP tank valve by turning OPD hand wheel
counterclockwise. If you hear a rushing sound, turn gas off
immediately. There is a major leak at the connection. Correct
before proceeding by calling Sears for replacement parts at
1-800-4-MY-HOME®.
Hold coupling nut and regulator
as shown for properconnection
to LP tank valve.

4. Brush soapy solution onto areas where bubbles are shown in
picture below:

6. Turn the coupling nut clockwise and tighten to a full stop. The
regulator will seal on the back-check feature in the LP tank
valve, resulting in some resistance. An additional one-half to
three-quarters turn is required to complete the
connection. Tighten by hand only - do not use tools.
NOTE:
If you cannot complete the connection, disconnect regulator and
repeat steps 5 and 6. If you are still unable to complete the
connection, do not use this regulator!

, Do not insert any tool or foreign objects into the valve outlet
or safety relief valve. You may damage the valve and cause
a leak. Leaking propane may result in explosion, fire, severe
personal injury, or death..
, If a leak is detected at any time, STOP and call the fire
department.
, If you cannot stop a gas leak, immediately close LP tank
valve and call LP gas supplier or your fire department!

, Never attempt to attach this grill to the self-contained LP gas
system of a camper trailer or motor home.
, Do not use grill until leak-tested.

6 " 463264407

A Never remove threaded
orifice at end of valves.

5. ff "growing" bubbles appear, there is a leak. Close LP tank
valve immediately and retighten connections. If leaks cannot
be stopped do not try to repair, Call Sears for replacement
parts at 1-800-4-MY-HOME®.
6. Always close LP tank valve after performing leak test by
turning hand wheel clockwise.

Safety Tips

For Safe Use Of Your Grill And To Avoid Serious

injury:

,A. Before opening LP tank valve, check the coupling nut for
tightness.
A When grill is not in use, turn offall control knobs and LP tank
valve.

• Do not let children operate or play near grill.
• Keep grill area clear and free from materials that burn.
• Do not block holes in bottom or back of grill.
• Check burner flames regularly.
• Use grill only in well-ventilated space. NEVER use in
enclosed space such as carport, garage, porch, covered
patio, or under an overhead structure of any kind.
• Do not use charcoal or ceramic briquets in a gas grill.
(Unless briquets are supplied with your grill.)
• Use grill at least 3 ft. from any wall or surface. Maintain

10 ft. clearance to objects that can catch fire or sources of
ignition such as pilot lights on water heaters, live electrical
appliances, etc.

A Never move grill while in operation or still hot.
A Use long-handled barbecue utensils and oven mitts to avoid
burns and splatters.
A Maximum load for shelves is 10 Ibs.
A The grease tray must be inserted into grill and emptied after
each use. Do not remove grease tray until grill has
completely cooled.
,A. If you notice grease or other hot material dripping from grill
onto valve, hose or regulator, turn off gas supply at once.
Determine the cause, correct it, then clean and inspect valve,
hose and regulator before continuing. Perform a leak test.
,A. Keep ventilation openings in cylinder enclosure (grill cart) free
and clear of debris.
A Do not store objects or materials inside the grill cart
enclosure that would block the flow of combustion air to the
underside of either the control panel or the firebox bowl.
,A. The regulator may make a humming or whistling noise during
operation. This will not affect safety or use of grill.
A If the regulator frosts, turn off grill and LP cylinder valve
immediately.This indicates a problem with the cylinder and it
should not be used on any product. Return to supplier!
,A. If you have a grill problem see the "Troubleshooting Section".

_fthe regulator frosts, turn off grill and LP tank valve
immediately. This indicates a problem with the tank and it
should not be used on any product, Return to supplier!
Apartment Dwellers:
Check with management to learn the requirements and fire
codes for using an LP gas grill in your apartment complex. If
allowed, use outside on the ground floor with a three (3) foot
clearance from walls or rails. Do not use on or under
balconies.
• NEVER attempt to light burner with lid closed. A buildup
of non-ignited gas inside a closed grill is hazardous.
• Never operate grill with LP tank out of correct position
specified in assembly instructions,
• Always close LP tank valve and remove coupling nut
before moving LP tank from specified operation
position.

463264407 • 7

Main Burner Lighting

Rotisserie Match Lighting

,L Do not lean over grill while lighting.

1. Open lid during lighting. Turn on gas at LP tank or gas
Source.

1. Open lid during lighting. Turn on gas at LP tank or gas
Source.
2. To ignite, turn IGNITION BURNER knob to_.
3. Push and hold ELECTRONIC IGNITION button. Be sure
burner lights and stays lit.
4. If ignition does NOT occur in 5 seconds, turn the burner
control to (_ OFF, wait 5 minutes, and repeat the lighting
procedure.

2. Place match into match holder (hanging from side of cart).
Light match, place into Match lighting hole on front side of
Rotisserie screen towards burner.
3. Push in and turn rotisserie knob to_.
and stays lit.

Be sure burner lights

5. Ignite other burners by turning the knob to(_, then turn
control knob to desired setting. Start with burner closest to
ignited burner.
m

cA,.,-,-,,:,,,,
if burner does not light, turn knobs to OFF,wait 5
minutes, and try again. Always close valve during the 5
minute waiting period. If the burner does not ignite with
the valve open, gas will continue to flow out of the burner
and could accidentally ignite with risk of injury.

Main Burner Match Lighting
,& Do not lean over grill while lighting.
1. Open lid during lighting. Turn on gas at LP tank or gas
Source.
2. Place match into match holder (hanging from side of cart).
Light match, place into Match lighting hole on left side of
firebox towards burner.
3. Push in and turn left knob to(_ position. Be sure burner lights

Sideburner Lighting
1. Open sideburner lid during lighting. Turn on gas at LP
tank or gas Source.
2. Turn sideburner knob to_, push and hold ELECTRONIC
IGNITOR button. Be sure burner lights and stays lit.
3. If sideburner does NOT light in 5 seconds, turn knob to (_
OFF, wait 5 minutes, then repeat lighting procedure.

CAUTIO. /L
Sideburner lid must be open when sideburner is in
operation.

and stays lit.
4. Ignite other burners by turning the knob to_), then turn control
knob to desired setting. Start with burner closest to ignited
burner.

Sideburner Match Lighting
1. Open sideburner lid during lighting. Turn on gas at LP
tank or gas Source.
2. Hold lit match to any port hole on the burner. Push in and
turn sideburner knob to_. Be sure burner lights and stays
lit.

CAUTIO.
* Putting out grease fires by closing the lid is not
possible. Grills are well ventilated for safety reasons.
, Do not use water on a grease fire. Personal injury may
result, if a grease fire develops, turn knobs and LP tank
off.
Rotisserie Lighting
1. Open lid during lighting. Turn on gas at LP tank or gas
Source.
2. To ignite, turn rotisserie knob to_, push and hold Electronic
Ignitor button. Be sure burner lights and stays lit.
3. If ignition does not occur in 5 seconds, turn burner control to
(_ OFF, wait 5 minutes, and repeat the lighting procedure.
8 " 463264407

, Do not leave grill unattended while preheating or
burning off food residue on high. if grill has not been
regularly cleaned, a grease fire can occur that may
damage the product. Follow instructions on General
Grill Cleaning and Cleaning The Burner Assembly to
prevent grease fires.

BeforeYourFirstCookout

General Grill Cleaning (continued)

o Light burners, check to make sure they are lit, close the lid and
warm up grill on HIGH for 15 minutes. This curing of parts will
produce an odor only on first lighting.

• Plated wire grates: Wash Grates and Heat Tents with
concentrated grill cleaner or use soap and water solution. Dry
thoroughly and store indoors between cookouts.

Burner Flame Check
, Light burner, rotate knobs from HIGH to LOW. You should see
a smaller flame in LOW position than seen on HIGH. Always
check flame prior to each use. If only low flame is seen refer to
"Sudden drop or low flame" in the Troubleshooting Section.

, Plastic parts: Wash with warm soapy water and wipe dry.
A Do not use citrisol, abrasive cleaners, degreasers or a
concentrated grill cleaner on plastic parts. Damage to and
failure of parts can result.
Porcelain grates: Because of glass-like composition, most
residue can be wiped away with baking soda/water solution or
specially formulated cleaner. Use non-abrasive scouring
powder for stubborn stains.

Hose Check
• Before each use, check to see if hoses are cut, worn or kinked.
Replace damaged hoses before using grill. Use only
valve/hose/regulator specified in the Parts List.

Normal
Hose

CAUTION
/

SPIDER

l[ 11

ALERT!

Turning Grill Off
, Turn all knobs to OFF position. Turn LP tank off by turning
OPD hand wheel clockwise to a full stop.

Ignitor Check
• Turn gas off at LP tank, Press and hold ignitor button. "Click"
should be heard and spark seen each time between collector
box or burner and electrodes. See "Troubleshooting" if no click
or spark.
Valve Check
• important: Make sure gas is off at LP tank before checking
valves. Knobs lock in OFF position. To check valves, first
push in knobs and release, knobs should spring back. If knobs
do not spring back, replace valve assembly before using grill.
Turn knobs to LOW position then turn back to OFF position.
Valves should turn smoothly.

If you notice that your grill is getting hard to light or that the
flame isn't as strong as it should be, take the time to check and
clean the burner's.

SPIDERWEBS
INSIDE TUBE

CONTROL PANEL

General Grill Cleaning
I

o Keep the outside of your grill looking new by cleaning it once a
month with warm soap and water or a non-abrasive cleaner. If
you don't have a grill cover, wipe off dust and grime before
starting your grill.
o Coating the cooking grids with spray-on cooking oil will keep the
food from sticking and make clean up easier. After cooking,
scrape the grates with a long handled, brass wire bristle brush.
o Check inside the grill bottom for grease build up and clean
often, especially after cooking fatty meat.
, Do not mistake brown or black accumulation of grease and
smoke for paint. Interiors of gas grills are not painted at the
factory (and should never be painted). Apply a strong solution
of detergent and water or use a grill cleaner with scrub brush
on insides of grill lid and bottom. Rinse and allow to completely
air dry. Do not apply a caustic grill/oven cleaner to painted
surfaces.

BURNER

i
Insomeareasofthecountry,
spiders
orsmall
insects
havebeen
knowntocreate
"flashback"
problems.
The spiders
spinwebs, build
nestsand layeggsin thegrill's burnertube(s)obstructingtheflow of
gasto the burner.Thebacked-upgas can ignitein the tubebehind
thecontrolpanel.This is knownas a flashbackand it can damage
yourgrill and evencauseinjury.
Topreventflashbacksand ensuregood performancethe burner
assemblyshouldbe removedfrom the grill and cleanedbeforeuse
wheneverthe grill has beenidle for an extendedperiod.
See "Cleaning the Burner" section in this manual
\

463264407 • 9

Cleaning the Burner Assemblies
Follow these instructions to clean and/or replace parts of Burner
Assembly or if you have trouble igniting grill.
1. Turn gas off at control knobs and LP cylinder,
2. Remove Cooking Grates and Heat Tents.

Cleaning Burners
We suggest three ways to clean the Burner Tubes. Use the one
easiest for you.
(A) Bend a stiff wire (a light weight coat hanger works well)
into a small hook. Run the hook through each Burner
Tube several times.

Tube Burners (figures A1-A2)
1. Remove screws and Flame Carryover Tubes from rear of
Burners shown A1.
.

3.
4.

(B) Use a narrow bottle brush with a flexible handle (do not
use a brass wire brush), run the brush through each
Burner Tube several times.

Remove screw and washer from Burner to disengage it from
Firebox Burner Bracket at back end of Firebox shown A1.
Remove screw to detach Electrode from middle Burner.
Electrode should remain in Firebox shown A2.
Carefully lift each Burner up and away from Valve openings.

Tube Burner
A1

2.
3.

(C) Wear eye protection: Use an air hose to force air into
the Burner Tube and out the burner ports. Check each
port to make sure air comes out each hole.
Wire brush entire outer surface of Burner to remove food
residue and dirt.
Clean any blocked ports with a stiff wire such as an open
paper clip.
Check Burner for damage, due to normal wear and corrosion l
some holes may become enlarged. If any large cracks or
holes are found replace Burner.

Re-assembly Burners in reverse order above.
VERY iMPORTANT:Burner tubes must re-engage over
valves. See illustration below.
Rotisserie Burner (figures B1-B2)
1. Remove Screws, Washers, and Nuts from Rotisserie Rear
Cover behind grill shown B1.
2. Remove Screw from Electrode shown B2.
3. Remove Screws, Washers, and Nuts from Rotisserie Burner

Correct
burner-to-valve
engagement

to detach from grill shown B2.
Rotisserie Burner
B1

Incorrect
burner-to-valve
engagement

VERY IMPORTANT: Rotisserie Burner tube must re-engage
over valve. See illustration below.

Washer

"Nut

Washer

10 • 463264407

Storing Your Grill
, Clean cooking grates.
, Store in dry location.
, When LP tank is connected to grill, store outdoors in wellventilated space and out of reach of children.
, Cover grill if stored outdoors.

Indirect Cooking
Poultry and large cuts of meat cook slowly to perfection on
the grill by indirect heat. The heat from selected burners
circulates gently throughout the grill, cooking meat or poultry
without the touch of a direct flame. This method greatly reduces
flare-ups when cooking extra fatty cuts because there is no direct
flame to ignite the fats and juices that drip during cooking.

, Store grill indoors ONLY if LP tank is turned off and
disconnected, removed from grill and stored outdoors.
, When removing grill from storage follow "Cleaning Burner
Assembly" instructions before starting grill.

Food Safety
Food safety is a very important part of enjoying the outdoor
cooking experience. To keep food safe from harmful bacteria,
follow these four basic steps:
Clean: Wash hands, utensils, and surfaces with hot soapy water
before and after handling raw meat and poultry.
Separate: Separate raw meats and poultry from ready-to-eat
foods to avoid cross contamination. Use a clean platter and
utensils when removing cooked foods.
Cook: Cook meat and poultry thoroughly to kill bacteria. Use a
thermometer to ensure proper internal food temperatures.
Chill: Refrigerate prepared foods and leftovers promptly.
For more information call: USDA Meat and Poultry Hotline at
1-800-535-4555 (In Washington, DC (202) 720-3333, 10:00 am4:00 pm EST).

1 Burner Cooking
Cook with direct or indirect heat.
Best for smaller meals or foods.
Consumes less fuel.

Indirect Cooking Instructions
, Always cook with the lid closed.
, Due to weather conditions, cooking times may vary. During
cold and windy conditions the temperature setting may need
to be increased to insure sufficient cooking temperatures

How To Tell If Meat is Grilled Thoroughly
• Meat and poultry cooked on a grill often browns very fast on the
outside. Use a meat thermometer to be sure food has reached
a safe internal temperature, and cut into food to check for
visual signs of doneness.
• Whole poultry should reach 180° F; breasts, 170° R Juices
should run clear and flesh should not be pink.
• Hamburgers made of any ground meat or poultry should reach
160° F, and be brown in the middle with no pink juices. Beef,
veal and lamb steaks, roasts and chops can be cooked to 145°
F.All cuts of pork should reach 160° F.
• NEVER partially grill meat or poultry and finish cooking later.
Cook food completely to destroy harmful bacteria.

2 Burner Cooking
Great indirect cooking on low.
Produces slow, even heating.
Ideal for slow roasting and baking.

• When reheating takeout foods or fully cooked meats like hot
dogs, grill to 165° F, or until steaming hot.

463264407 • 11

Description
BottomShelf........................

LockingCaster......................
FixedCaster........................

LeftSide Panel......................

Part #
80010508

Description

Part #

80000268
80004093

Fascia,Left.........................
80010534
#1/4-20x5/8"Screw.......
HMS02520063CPNSTSS

Side Burner.........................

80010510

5mmWasher,Silicon............

HFWM51D9ODSN

RightSide Panel.....................
80010509
#1/4-20xl/2" Screw....... HMS02520050CPNSTSS

5mmWasher,Lock..............

HSWM5RHSPSS

#10-24x3/8"Screw.........

#1/4" Washer,Lock..................

HSW025SS

WindDiverter.......................

80006385

LowerBack Panel,Cart ...............

80010511

Clip,Side Burner ....................

80006434

TemperatureGauge..................

80006666

Grate,Side Burner...................

80006640

Heat Shield.........................

80010537

80004311

HMS01924038PNSTSS

Bezel,TemperatureGauge.............

80006354

LogoPlate,Kenmore.................

80010544

HardwareTopLidAssembly............

80009607

Screw,Tapping,#8x3/8"........
HAB016038CPNSD
TankExclusionWire..................
80010538

TopLid Insertw/Sides ................

80010542

#8-32x3/8"Screw........

InnerInsert,TopLid ..................

80010543

#8 Washer,Lock...................

Door,Left ..........................

80010541

80010545
80010548

TopLid Handle......................
RotisserieCover.....................

63
64

DoorHandle........................

80010540

FrontPlate,Rotisserie................

80010525

FrontScreen,Rotisserie...............

80007246

Door,Right .........................
80010539
#6-32x3/8"Screw..........
HMS01432038PFSTSS

BackPlate,Rotisserie ................

80010524

FlameTamer........................

80003332

Burner,Rotisserie....................

80010526

CookingGrate,Set of 3 ...............

80010436

Electrode,Rotisserie .................

80010527

WarmingRack ......................

80007275

RearPanel,Firebox..................

80010518

1
1

GreaseTrayBody....................
MatchHolder .......................

80008970
80006579

HMS01632038CPNSTSS
HSW016SS

RotisserieValveSupportBracket........

80007085

CarryoverTube......................

80006504

RotisserieHoseBracket...............

80010816

80005703
80010513

HeatShield,f/Regulator Hose..........

80010817

Burnerw/Spider Guard ...............
FireboxBowl........................

26
27

LeftSide UpperPanel ................

80010514

CasterWrench ......................

80000283

DoorMagnetAssembly...............

80008850

80010515
80010516

1
1

AssemblyManual....................

80010502

1
1

80010517
80010520

HardwarePack(for retailerstore only).... 80010501

RightSide Panel,Firebox..............
ControlPanel .......................

LogoPlate,Dual Fuel.................

80005594

ElectronicIgnitorKit, Mainand SB.......

80010519

Button,ElectronicIgnitor ..............

80004343

Valve/Manfold/Regulator
..............
Bezel,ControlKnob ..................

80010521
80005596

ControlKnob........................

1
8

FrontBracew/Door Magnet ...........
80010512
#1/4-20xl-3/4"Screw..... HMS02520175CPNSTSS

16 ... 1/4-20xl/2"Screw

41
42

1
1

UpperBack Panel....................
TowerBar ..........................

80010529
80010532

8 .... 1/4-20xl-3/4"Screw

43
44

RightSideShelf .....................

80010530

Fascia,Right........................

80010531

Lid,Side Burner .....................

80010536

Side BurnerPan.....................

80010535

LeftSide Shelf ......................

80010533

12 " 463264407

RightSide UpperPanel ...............
LeftSide Panel,Firebox...............

Not Pictured:

ScrewNut Pack (forpurchaser).........
8 . . #8-32x3/8"Flat HeadScrew
3 .
2 .

. #8x3/8"Self-tapScrew
. #8-32x3/8"Screw

80004299

2 .
2 .

.#8 Lock Washer
. #10-24x3/8"Screw

Bezel,RotisserieKnob................

80010528

2 .... #10 LockWasher

ControlKnob,Rotisserie ..............

80007251

2 .... 5mm SiliconWasher

80010547

6 .... 1/4-20x5/8"Screw
30 ... 1/4 LockWasher
NaturalGasConversionKit (Not Included)4184609

--34

46
57

27
29

56j_

3O
32_

i i4-53
_"-54

@0@@

5'9

@ @

_9
50.
7

66
r

3
463264407 " 13

Bottom Shelf
Attachthe two locking castersat the rear of the bottom
shelf.
Attachthe twofixed castersat thefront.
Use the }rovidedcasterwrenchto fully tightencasters.

Fixed Caster

T
Bottom Shelf

14 • 463264407

Side Cart Panels
Attachsidepanelsto bottomshelf.
Use three1/4-20x1/2"screwsand 1/4" lockwashersper
panel.
IMPORTANT:Panelwith bracket must be on left side of
bottom shelf,

1/4" LockWasher

1/4"

1/4-20x1/2"Screw

LeftSide Panel

ht Side Panel

463264407 • 15

Cart LowerBack Panel
Placelowerback panelbetweenside panelsat rear of
bottomshelf.
Securelowerback panelto sidepanelsusingtwo !/420x1/2" screwsand 1/4" lockwasherson each side.
Securemiddleof lowerback panelto bottomshelf usingone
1/4-20x1/2"screwand 1/4" lock washer.

1/4" LockWasher

1/4-20x1/2"Screw

Lower Back Panel

16 • 463264407

Grill Head,Cart Assembly
This step requires two people to lift and position grill
head onto cart.
Carefullylowerthegrill headontothe cart,aligningslotsat
bottomof grill headwith postson cart side panels.
Grill head must face open sideof cart.

Grill Head

Post

BeforeAssembling the grill
head on the lowercart

After Assembling

463264407 • 17

FrontDoor Brace
Insertfront braceundercontrolpaneland betweencart side
panels.
Secureusingtwo 1/4-20xl-3/4" screwsand 1/4" lock
washerson each side.
NOTE:MAKESURETHE SCREWSARE IN THE LOWEST
POSSIBLEPOSiTiONiN THE MOUNTINGHOLES..

1/4" LockWasher

1/4-20xl-3/4"Screw

18 • 463264407

Cart Upper Back Panel
On backof grill, placecart upper backpanel betweenside
panelsandabovecart lowerback panel.
Securecart upperbackpanel,in lowerholes,usingone 1/420xl-3/4" screwand 1/4" lockwasheron eachside shown
A.

Securecart upperbackpanel to lowerbackpanelfrom inside
usingone 1/4-20x1/2"screwand 1/4" lock washerin the
centerhole shownB.
Do not fully tighten screws until side shelf installationis
complete in later steps,

l/4"LockWasher

1/4-20x1/2"Screw

1/4-20xl-3/4"Screw

RearUpperPanel

463264407 • 19

Right and LeftShelf Assembly
Attachfour 1/4-20x1/2"screwsand 1/4" lockwashers

1/4" Lock Washer
1/4-20xl/2"Screw
1/4-20xS/8"Screw

throughside shelf holes(rightshelf ONLY),into towelbar
shownA.
Attachtwo 1/4-20x5/8"screwsand 1/4" lock washersto the
side cart panelshownB. Tightenonlyone-fourthof screw
length,so that shelf bracketwillslide betweencart and
washers.Donot tighten.

1/4-20x14/4" Screw

Insertsideshelf overscrewsand washersthroughbracket
shown B-Cand D-C.Make surethe middleshelf tabsare
insertedintothe cart side panelcut-outshownC.
Attachone 1/4-20x!-3/4" screwand 1/4" lock washerat the
rearshelfflangeshown D.
Attachone 1/4-20x5/8"screwand 1/4" lockwasherto front
shelf flangeshown E. Go backand fully tightenscrews
shown B.

Only Right Shelf Shown ForAssembly, repeatabove
steps B-E for Left sideburner shelf.

1/4-20xl-3/4" Screw

r--4

20 • 463264407

SideburnerControl Knob Assembly
First,removethe two #8-32x3/8"screwand #8 lockwasher
from the sidebumervalve bracketshownA.

0
#8 LockWasher
#8-32x3/8"Screw

Positionsideburnervalve bracketbeneathsideburnershelf
fasciaso that valvestemcomesthroughlargercenterhole in
fasciashownB.
Attachsideburnerbezeltofascia usingscrewsthat were
removedfrom bracketshown B.
PresssideburnercontrolknobontovalvestemshownB.

O
#8-32x318"Screw
And
#8 Lock Washer

Sideburner Shelf

(Fasciaoutlined for view)

Fascia

Sideburner Bezel
Control Knob

463264407 • 21

SideburnerBurner

Insertfront of sidebumerburnerthroughleft shelf cut-out
shownA. Centerstud on bottomrear of burnerfits intocenter
hole in burnerbracketon left shelf.

#10 Lock Washer

Make sureburnertubealignscorrectlyontosideburnervalve
underneathleft shelf shownB.
Secureburnerto bracketusingtwo #10-24x3/8"screwsand
5ram siliconand#10 lockwashersshownC.
Attachsideburnerigniterwirefrom ignitermoduleto electrode
tip underneathleft shelf shownD.

[]

Sideburner Burner

Left Shelf Cut-out
with Bracket

[]

22 • 463264407

[]

5 mm Silicon
Washer

#10-24x3/8"Screw

SideburnerWind Diverter, Sideburner Cap and Clip,
Sideburner Grate
Placesideburnerwinddiverteroversideburneraligningcutout in diverterto fit aroundelectrodeshownA.
Placeburnercap ontosideburnerand attachsideburnercap
clip shownB.

SidebumerCapClip

Placesideburnercookinggrateontosideburnershelf,
aligninggratelegswith holesin shelf shownA.

Q
Sideburner Cookinc

Burner C_

Sideburner Wind Diverter

463264407 • 23

Heat Shield Assembly
Insideof cart shownA, insertrear shieldtabs of tank heat
shieldthroughthreecut out slotson upperbackpanel shown
A and B for rear view of cart. Makesure greasetray slide
is alignedwith cut out in upperback panelshownC.

T
#8x3/8"Self-tappingScrew

Front Shield Tabs
w/Hole

Attachfront shieldtabs of tank heatshieldunderfront brace
usingthree#8x3/8"self-tappingscrewsshownD.

RearShield Tabs

24 • 463264407

Assembling TankExclusion Wire
Insertrear left wireend of tank exclusionwireinto lowerback
panelleft slot,then lowerrightwire end intorightslot shown
A.

#8 LockWasher
#8-32x3/8"Screw

Attachfront rightwire end of tank exclusionwire to the left
side panelbracketusingone #8-32x3/8"screwand #8 lock
washershownB.
Attachbottomwireend of tank exclusionwireto the bottom
panel usingone #8-32x3/8"screwand #8 lockwasher
shownC.

463264407 • 25

LeftDoor and Right Door

#8-32x318"Flat
Head

Attacheach door by insertingtop hingetab intoslot on front
of cart side panel. Theninsert bottomhingetab into bottom
slot on front of cart side panelmakingsuremiddlehingetab
also insertintomiddleslot.
Secureeachdoor to cart side panelusingfour #8-32x3/8flat
head screws.

T
#8-32x3/8"Fiat HeadScrew
Middle

Bottom

26 • 463264407

Flame Tamers
Installeachflametamer by insertingone end of flametamer
intoslotsat front of fireboxbracketand restingoppositeend
on pin locatedat backof firebox.

FlameTamer

463264407 • 27

D
Cooking Grateand Warming Grate
Placecookinggratesonto thefireboxas shown.
Insertthe threewire endsat rear of warmingrackinto holes
in rear offirebox.
Frontwiresof warmingrack reston sidesof fireboxshownA.

Warming Rack

g Grate

28 • 463264407

LPTank
LPTANK ISSOLDSEPARATELY.Filland leakcheckthe tank beforeattachingtogrill and regulator(see Use& Care
section).
Oncetank hasbeenfilledand leakchecked,placecylinderintocut-outin bottomshelf.Makesure tank valve is
facing front of grill.
Securetankwith tank screwunder bottomshelf.Insertregulatorthroughlarge hole in left side panel.See Use & Care
section of this manual to perform the "Burner FlameCheck" and for importantsafety instructionsbefore
using.

/t,, CAUTioN/L
LP Tank valve must face to front of cart once
tank is attached. Failure to install cylinder
correctly may allow gas hose to be damaged
in operation, resulting in the risk of fire.
Always keep LPtank in upright position during use,
transport, and storage.

463264407 • 29

GreaseTray
On backof grill,slide greasetray throughopeningon upper
back panel.

II l cAuT,o.
Failure to install grease tray will
cause hot grease to drip from bottom
of grill with risk of fire or property
damage.

AssemblingElectronicIgnitionButton
Unscrewelectronicignitionbuttonon front of controlpanel.
InsertAAbatteryintoignitor,negative (--} end first. Replacebutton.

AA Battery

Electronic ignitionButton

30 • 463264407

Cooking Table
Cooking times and temperatures may vary according to specific recipes, cooking conditions or barbecue equipment used. Take these
factors into consideration to insure best results. If you use the indirect cooking method (indirect cooking is lighting only one burner and
placing food on opposite side of cooking grate), allow more grilling time.
Temperatures: High = 650°F / Medium = 450°F / Low = 300°R
Food

Setting

Cooking Time

Beef
Hamburger 112"thick

Medium

Med: 7-10 min./Well done: 10-15 min.

Steak 112"

Medium-Hot

Rare: 3-6 min. / Med: 6-9 min./Well done: 9-12 min.

Roast

Low

Rare: 18-22min. per lb. / Med: 22-28 min. per lb. / Well done: 28-32 min. per lb.

Pork
Chops 112"

Medium

Well done: 15-20 min.

Ribs 5-6 Ibs.

Low-Medium

Well done: 45-90 min.

Roast 3-5 Ibs.

Low-Medium

Well done: 18-23 min. per lb.

Ham Steak 112"

Medium-Hot

12-15 min.

Ham 5 lb. fully cooked

Low-Medium

20 min. per lb.

Lamb
Chops 112"

Medium

6-12 min.

Poultry
Chicken 2-1/2 to 3-1/2 Ibs.

Low

1 hr., 15 min. to 1 hr., 30 min.

Chicken halved or quartered

Low

40-60 min.

Turkey

Low-Medium

18-20 min. per lb.

Seafood
Steaks 1" thick

Medium-Hot

Well done: 10-25 min.

Fillets 6-8 oz.

Medium-Hot

8-12 min.

Shrimp large or jumbo

Low-Medium

8-12 min.

Venison
Steak 1" thick

Medium

Rare: 8-10 min./Med: 10-12 min.

Burgers 1/2"

Medium

Rare: 10-12 min./Med: 12-15 min.

Roast 3-4 Ibs.

Low-Medium

Rare: 20-22 min. per lb./Med: 22-25 min. per lb.

Vegetables
Baking Potato whole

Low

Wrap vegetables in foil
55-60 min.

Onions whole

Low

45 min.

Tomatoes half

Medium

30-40 min.

Corn whole

Low

35-45 min.

Mushrooms

Medium

15-20 min.
463264407 • 31

Troubleshooting Call 1-800-4-MY-HOMEfor Assistance if required.
EMERGENCIES: if a gas leak cannot be stopped, or a fire occurs due to gas leakage, call the fire department.

Gasleakingfrom
cracked/cut/burned
hose.

. Damagedhose.

. Turnoff gas at LP tank. If hoseis cut or cracked,replace
valve/hose/regulator.
See LP TankLeakTestand Connecting
RegulatorToThe LPTank.

Gasleakingfrom LP
tank.

. Mechanicalfailuredue to rustingor
mishandling.

. Turnoff LP tankvalve.

Gasleakingfrom LP
tank valve,

. Failureof tank valvefrom mishandlingor
mechanicalfailure.

. Turnoff LP tank valve.ReturnLP tank togas supplier.

Gasleakingbetween
LP tankand regulator
connection.

. Improperinstallation,connectionnot
tight,failureof rubberseal.

. Turnoff LP tankvalve.Removeregulatorfrom cylinderand visually
inspectrubbersealfor damage.See LP TankLeakTestand
ConnectingRegulatorToTheLP Tank.

Firecomingthrough
controlpanel.

. Fire in burnertubesectionof burnerdue
to partialblockage.

. Turnoff controlknobsand LP tankvalve.Leavelid open to allow
flamesto die down.After fire is out and grill is cold, removeburner
and inspectfor spidernestsor rust.See NaturalHazardand Cleaning
The BurnerAssemblypages.

Greasefire or
continuousexcessive
flamesabovecooking
surface.

. Toomuchgreasebuildupin burnerarea.
. Turnoff LP tank valve.Leavelid opento allowflamesto die down.
After cooling,cleanfood particlesand excessgreasefrom inside
fireboxarea,greasecup/pan/tray,and othersurfaces.
GAS ISSUES:

Burner(s)will not light
usingignitor.

. Tryingto lightwrongburner.

. See instructionson controlpaneland sectionin the Use and Care.

. Burnernotengagedwith controlvalve.

. Makesure valvesare positionedinsideof burnertubes.

. Obstructionin burner.

. Ensureburnertubes are notobstructedwith spiderwebs or other
matter.See cleaningsectionof Useand Care.

. No gasflow.

. Makesure LP tank is notempty.If LP tank is notempty,referto
"Suddendrop in gasflow."

. Vaporlockat couplingnut to LP tank.

. Turnoff knobsand disconnectcouplingnutfrom LP tank.Reconnect
and retry.

. Couplingnutand LP tank valve notfully
connected.

. Turnthecouplingnut approximatelyone-halfto three-quarters
additionalturnuntil solidstop.Tightenby hand only- do notusetools.

ELECTRICALISSUES:

Continuedon next
page.
32 • 463264407

. Electrodecrackedor broken;"sparksat
crack."

. Replaceelectrode.

. Electrodetip not in properposition.

. Tip of electrodeshouldbe pointingtowardport holein burner.The
distanceshouldbe 1/8"to 3/16".Adjust if necessary.

. Wireand/orelectrodecoveredwith
cookingresidue.

. Cleanwireand/orelectrodewith rubbingalcoholand cleanswab.

. Wires are looseor disconnected.

. Reconnectwiresor replaceelectrode/wireassembly.

. Wires are shorting(sparking)between
ignitorand electrode.

. Replaceignitorwire.

Troubleshooting (continued)

Burner(s)will not light
usingignitor.

Burner(s)will not
matchlight.

, Push-button
sticksat bottom..

, Replaceignitor.

, Sparkingbetweenignitorand electrode.

, Inspectwireinsulationand properconnection.Replacewires if
insulationis broken.

, See "GAS ISSUES:"on previouspage.
, Impropermethodof match-lighting.

, See"Match-Lighting"sectionof Useand Care.

, Outof gas.

, Checkfor gas in LP tank.

, Excessflow valvetripped.

, Turnoff knobs,wait 30 secondsand light grill.If flamesare still low,
turnoff knobsand LPtank valve.Disconnectregulator.Reconnect
regulatorand leak-test.Turnon LP tank valve,wait 30 secondsand
thenlightgrill.

, Vaporlock at couplingnut/LPtank
connection.

, Turnoff knobsand LP tank valve.Disconnectcouplingnutfrom
tank.Reconnectand retry.

, Highor gustingwinds.

, Turnfront of grill to face windor increaseflame height.

, Lowon LP gas.

, RefillLP tank.

, Excessflow valvetripped.

, Referto "Suddendrop in gasflow"above.

, Greasebuildup.

, Cleanburnersand insideof grill/firebox.

, Excessivefat in meat.

, Trimfat from meat beforegrilling.

, Excessivecookingtemperature.

, Adjust (lower)temperatureaccordingly.

Persistentgreasefire.

, Greasetrappedbyfood builduparound
burnersystem.

, Turnknobsto OFF.Turngas off at LPtank. Leavelid in positionand
letfire burn out.After grill cools,removeand cleanall parts.

Flashback...
(firein burnertube(s)).

, Burnerand/orburnertubesare blocked.

, Turnknobsto OFF.Cleanburnerand/orburnertubes.See burner
cleaningsectionof Use andCare manual.

Unabletofill LP tank.

, Somedealershaveolder fill nozzles
with wornthreads.

, Thewornnozzlesdon'thaveenough"bite"to engagethe valve.Try
a secondLP dealer.

, Greasebuildupor foodparticlesin
end(s)of carryovertube(s).

, Cleancarry-overtube(s)with wire brush.

Suddendrop in gas
flow or lowflame.

Flamesblowout.

Flare-up.

Oneburnerdoesnot
lightfrom other
burner(s).

463264407 • 33

Troubleshooting - Electronic ignition

SECTIONI
Nosparksappearat
any electrodeswhen
ignitionbuttonis
pushed;no noisecan
be heardfrom spark
module.

SECTIONII
Nosparksappearat
any electrodeswhen
ignitionswitchis
pushed;noisecan be
heardfrom spark
module.

SECTIONIII
Sparksare present
butnotat all
electrodesand/ornot
at full strength

, Batterynot installed
properly.

. Checkbatteryorientation.

. Installbattery(makesure that"-" and "+"
connectorsare orientedcorrectly,with "-" end up
and "+" enddown.)

. Deadbattery.

. Has batterybeen used
previously?

. Replacebatterywith newAAA-sizealkalinebattery.

. Buttonassemblynot
installedproperly.

. Checkto ensurebutton
assemblyis fully engaged.
Buttonshouldtravel up and
downwithoutbinding.

. Removebuttoncap assemblyand reinstall,making
sureit canbe fully engaged.

. Faultyspark module.

. If no sparksare generated
with newbatteryand good
wireconnections,moduleis
faulty.

. Replacespark moduleassembly.

. Outputleadwires not
connected.

. Are outputlead wireson and
tight?

. Removeand reconnectall outputleadwires at
moduleand electrodes.

. Electrodetip not in
properposition.

. Are the electrodetips
pointingin the right
direction?Is the gap too big?

MainBurners:
. Tip of electrodeshouldbe pointingtowardporthole
in burner.The distanceshouldbe 1/8"to 3/16".
Adjustif necessary.
Sideburner:
. Tip of electrodeshouldbe pointingtowardgas port
openingon burner.Thedistanceshouldbe 1/8"to
3/16".Adjustif necessary.

. Outputleadwires not
connected.

. Are outputlead wireson and
tight?

. Removeand reconnectall outputleadwires at
moduleand electrodes.

. Arcingto grillaway
from burner(s).

. If possible,observegrill in
darklocation.Operate
ignitionsystemand lookfor
arcingbetweenoutputwires
and grill frame.

. If sparksare observedotherthanfrom burner(s),
wire insulationmay be damaged.Replacewires.

. Weakbattery.

. All sparkspresentbutweak
or at slow rate.

. Replacebatterywith a newAAA-sizealkaline
battery.

. Electrodesare wet.

. Has moistureaccumulated
on electrodeand/orin burner
ports?

. Use papertowel to removemoisture.

. Electrodescrackedor
broken"sparksat
crack".

34 • 463264407

. Inspectelectrodesfor
cracks.

. Replacecrackedor brokenelectrodes.

Your Home
Forrepair-in yourhome-ofall
majorbrand appliances,
lawn and garden equipment, or heating and cooling systems,
nomatterwhomadeit,
nomatterwhosoidifl
Forthe replacement parts, accessories and
owner'smanualsthatyouneedtodo-it-yourself.
ForSears professional installation of home appliances
anditemslikegaragedooropenersandwaterheaters.
1-800-4-MY-HOME

® (1-8oo-469-4663)

Ca,,an time, a oandCanada)
nioht( .S.A.
www.sears.com

www.sears.ca

Our Home
For repair of carry-in items like vacuums, lawn equipment,
and electronics, call or go on-line for the location of your nearest

_,_
iiiiiiiiiiiiiiiiiii

1-800-488-1222

iiiiiiiiiiiiiiiiiii
HHHHHHHH_

Call anytime, day or night (U.S.A. only)

iiiiiiiiiiiiiiiiiii

www.soors.com

.................................................

iiiiiiiiiiiiii
iiiiiiiiiiiiiiiiiii

To purchase a protection agreement (U.S.A.)
ormaintenanceagreement(Canada)
1-800-827-6655

(U.S.A.)

iiiiiiiiiiiiiiiiiii

onaproductservicedbySears:
1-800-361-6665

(Canada)

....................
Para pedirservicio de reparaci6n
adomicilio, yparaordenarpiezas:
1-888-SU-HOGAR

® Registered

Au Canada pour service en francais:
1-800"LE-FOYERMC
(1-800-533-6937)

(1-888-784-6427)

Trademark

iiiiiiiiiiiiiiiiiii

iiiiiii:!!:!!:!!:!!:!!:!!:!!:!!:!!:!!:!!:!!:!!:!!i

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
_

iiiiiiiiii

/ _MTrademark

/ sMService
SM

® Mama Registrada / _MMarca de Fabrica /
Mc Marque de commerce / M° Marque deposee

iiiiiiiiiiiiiiiiiii
iiiiiiiiiiiiiiiiiii
iiiiiiiiiiiiiiiiiii

www.sears.ca

Mark of Sears

Brands,

Marca de Servicio de Sears
de Sears Brands, LLC

LLC
Brands,

LLC
© Sears

Brands,

LLC

463264407 • 35

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Page Count                      : 35
Page Layout                     : SinglePage
Page Mode                       : UseNone
Producer                        : Goby Monitor Application version 3, 2, 1, 4
Create Date                     : Wed Aug 15 11:40:13 2007
Author                          : 
Title                           : 
Subject                         :

EXIF Metadata provided by EXIF.tools

Kenmore 41516237 User Manual GAS GRILL Manuals And Guides L0703044

KENMORE Grill, Gas Manual L0703044 KENMORE Grill, Gas Owner's Manual, KENMORE Grill, Gas installation guides

Navigation menu

Versions of this User Manual:

Views

Navigation