Kenwood USA 30633120 Repeater User Manual Manual

Download:
Mirror Download [FCC.gov]
Document ID	83693
Application ID	D5PY30gbwcXSyetakE1bLg==
Document Description	Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	16.99kB (212400 bits)
Date Submitted	2000-01-27 00:00:00
Date Available	2000-02-11 00:00:00
Creation Date	2000-01-27 09:47:32
Producing Software	Acrobat PDFWriter 3.02 for Windows NT
Document Lastmod	2000-01-27 09:48:20
Document Title	Manual
Document Author:	Bill

I KH-l‘I-U/ I KH-64U
INSTRUCTION MANUAL
I\I_I V VVVVI—I
KENWOOD CORPORATION
o 862-1136-00 (K)
09080706050403020100
THANK YOU!
We are grateful you purchased this KENWOOD repeater.
We believe this aasy-to-program repeater will be highly
effective in your communications system, and will keep
personnel operating at peak efficiency.
KENWOOD incorporates the latest in advanced
technology into all of our products. As a result, we ieel
strongly that you will be pleased with the quality and
features of this product.
FEATURES
. You can easily program channel data using the KPG-47D
version 2.00 or later (optional) on a PC,
- You can recall 1 of 32 preset channels using either a PF key or
the extemal control line. '
. The tirmware can be written to the Flash memory through an
external source,
. QT/DQT signalling can be programmed on each channel. It
decodes up to 16 different OT/DQT tones at one time.
- when using the KPG»47D version 2.00 or later (oEtional). RX
PLL lock voltage, RX input signal strength, TX PL lock
voltage, TX output power, and the power supply voltage can be
monitored on a PC.
. The interface port can be used with external equipment, such
as a repeater controller,
. The repeater has multi-mode capabilit .
Wide: 30 kHz, 25 kHz/ Narrow: 15 k 2,125 kHz
Wide: 25 kHz! Narrow: 125 kHz
- You can adjust the lollowing lunctions lrorn a PC:
. Squelch (Analog! RSSI)
. Signalling Balance
- Digital Pager Balance
. Maximum Deviation
- Signalling Deviation (TD)
- QT Deviation
- DQT Deviation
. CW Deviation
. Digital Pager Deviation
. Test Tone Deviatlon
' Remote TA
- RF Power
- RX Audio Signal Output lFtA)
- RX Detector Signal Output (FtD)
. TX Audio Input (TA)
- Voting Tone Level
PRECAUTIONS
- Do not expose the unit to rain or moisture; to prevent lire or
electric shock.
~ Do not open the unit under any circumstances: to avoid risk of
electric shock.
. Do not expose the unit to long periods at direct sunlight, nor
place it close to heating appliances.
(TKFi-740)
(TKR-840)
~ Do not place the unit in excessively dusty and/or humid areas.
nor on unstable surfaces,
. If you detect an abnormal odor or smoke coming from the unit,
disconnect the power lrorn the unit immediately. Contact your
KENWOOD service center or dealer.
NOTICES TO THE USER
FCC WARNING
This equipment gene/ates or uses radio frequency energy. Changes or
modilica ions to this equipment may cause harmful lnlerlerence unless
the modifications are expressly approved in the inst/Devon manual. The
user could lose the authon'ty to operate this equipment ii an
unaumon’zed change or modification is nude.
WARNING:
GOVERNMENTLAWPROHIBITS THE OPERATlON OF
UNLICENSED RADlO TRANSMITTERS WiTH/N THE
TERRITORIES UNDER GOVERNMENT CONTROL.
ILLEGAL OPERATION IS PUNISHABLE EVFlNE OFt‘
lMF'R/SONMENT OR BOTH.
REFER SERVICE TO QUALIFIED TECHNICIANS DNLY,
UNPACKING AND CHECKING EQUIPMENT
Note: The following unpacking intonation is for use by your KENWOOD
dealer, an authorized KEN WOOD service facility, or the Iaclary.
Carefully unpack the repeater. We recommend that you
identify the items listed in the following table before
discarding the packing material. If any items are missing
or have been damaged during shipment, file a claim with
the carrier immediately.
g Item , , ,
Front glass BlO-2590-X4 1
Fuse (4 A) FOS-4027-X5 1
Handles and screw set K01-0421-X5 1
Power cable assembly E30—3344-X5 1
Lead wire with connector E81-3228—X5 1
Square plug E59v0410-X5 1
Dressed screw N08-0543-X4 1
Instruction manual 362-1136»XX 1
I INSTALLATION
- To install the handles onto the front panel of the receiver,
align the handles with the holes on the front panel. then
secure the handles using the supplied screws.
Please consult your dealer for installing the repeater and
antenna.
MICROPHONE
Connect a KENWOOD optional microphone to the
MICROPHONE jack on the front panel.
IO U@ (250 (7130 @
TTWVM;
|| Q|
ml meg
to time etc
0) Speaker
C2) REF (reference) Indicator
Lights red when using an external relerence
frequency. Lights green when using the internal
reierence frequency.
@ Busv indicator
Lights green while a signal is being received.
® TX (transmit) Indicator
Lights red while transmitting.
® POWER indicator
Lights green when power is applied.
© Display
Two, 7—segment digits display the channel number
or status.
I Rear Panel
coo %
® RX IN lack
Connect a RX antenna or a duplexer to this BNC
receptacle
® TESTISPKR jack
Test input/output jack. Connect an external
speaker to this jack.
© FlEMT 1/0 jack
Connect an external remote controller to this jack.
(D CONTROL lIO Jack
Connect an external programming device or
repeater controller to this DB-25 interface.
REPEATER OPERATION
Note: Please consult your dealer Iorprogrammlng me repeater.
When power is applied to the unit, the POWER
indicator lights green.
Turn the VOLUME control clockwise until a click
sounds, to unmute the volume. Rotate to adjust the
volume. Turn the VOLUME control counterclockwise
fully to mute the volume.
The BUSY indicator lights green while receiving a
signal, and the TX indicator lights red while
transmitting.
® Programmable Function keys
Press these keys to activate their programmable
functions.
TEST switch
Press to transmit an unmodulated signal with no
external microphone connected.
® VOLUME control
Turn clockwise until a click sounds, to unmute the
volume. Rotate to adjust the volume. Turn
counterclockwise fully to mute the volume.
on MICROPHONE jack
Connect a microphone to this B-pin modularjack.
© EX‘IZREF IN jack
Connect an external reierence frequency (10 MHz,
-10 dBm or higher) to this BNC receptacle.
(5) DC 13.8V1ack
Connect a 13.8 V DC power supply to this jack.
® FUSE
Insert a 4 A blade tuse into this luse holder.
TX OUT jack
Connect a TX antenna or a duplexer to this BNC
receptacle
TRANSCEIVER OPERATION
l Receive
Adjust the volume to your desired level. You may
need to readjust the volume when you receive a
message from your dispatcher or another member in
your fleet.
' - The BUSY indicator lights while a signal is being
received.
-I Transmit
1 Listen to the channel belore transmitting, to make
sure it is not being used.
2 Press the PTT switch and speak in your normal
speaking voice.
- FCC regulations require that you identify the
station you are calling as well as your own
station (your assigned call sign).
- The TX indicator lights while transmitting.
3 When you finish speaking, release the PTT switch.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Creator                         : 
Create Date                     : 2000:01:27 09:47:32
Title                           : 
Author                          : Bill
Producer                        : Acrobat PDFWriter 3.02 for Windows NT
Subject                         : 
Modify Date                     : 2000:01:27 09:48:20
Page Count                      : 2

EXIF Metadata provided by EXIF.tools