Kenwood Z828Mp Users Manual Z828 (EN)
Z828MP to the manual 577eeb7b-40f5-4ba7-8fbf-f152fce49b35
2015-01-23
: Kenwood Kenwood-Z828Mp-Users-Manual-263616 kenwood-z828mp-users-manual-263616 kenwood pdf
Open the PDF directly: View PDF .
Page Count: 60
Download | |
Open PDF In Browser | View PDF |
Z828MP CD-RECEIVER INSTRUCTION MANUAL B64-2089-00 (EW) English Contents Safety precautions ........................3 Handling Compact discs................6 Notes on playing MP3 files ...........8 General features Power ........................................................10 Volume.......................................................10 Attenuator..................................................11 Switching Modes.......................................11 Loudness ...................................................11 Switching Display Mode............................12 Switching the Upper Part Display..............12 Switching the Lower Part Display .............14 Switching Full-Screen Display....................15 TEL Mute...................................................15 Switching Display during the Standby mode .......................................16 Theft Deterrent Faceplate .........................16 System Q ..................................................16 Speaker & Woofer setting .........................17 Non-Fading Output ....................................17 Dual Zone System .....................................18 Audio control features Audio Control Setting ................................19 Bass Centre Frequency ............................19 Bass Level .................................................19 Bass Quality Factor ...................................19 Bass Extend ..............................................19 Middle Centre Frequency .........................20 Middle Level..............................................20 Middle Quality Factor................................20 Treble Centre Frequency ..........................20 Treble Level ...............................................20 Balance Level ............................................20 Fader Level................................................20 Non-Fading Level.......................................20 High-pass Filter Frequency for Front Output ....................................21 High-pass Filter Frequency for Rear Output .....................................21 Low-pass Filter Frequency for Non-Fading Output ..........................21 Phase for Non-Fading Output ...................21 Volume Offset ...........................................21 Tuner features Tuning........................................................22 Station Preset Memory.............................22 Direct Access Tuning .................................23 Preset station seek with Programme service name.............23 RDS features RDS (Radio Data System) .........................24 Enhanced Other Network .........................24 Alarm.........................................................24 Traffic Information Function.......................25 Presetting Volume for Traffic Information/News..................................25 Programme Type (PTY) Function ...............26 Changing Language for Programme Type(PTY) Function ............27 Radio Text Scroll ........................................27 CD/External disc control features Playing CDs ...............................................28 Playing Other Disc mode ..........................29 Fast Forwarding and Reversing Disc Play................................................29 Track Search ..............................................30 Disc Search ...............................................30 Track / Disc Repeat....................................30 Track Scan .................................................30 Random Play .............................................31 Magazine Random Play.............................31 Text Scroll..................................................32 Presetting Disc Names (DNPS).................32 Disc Name Preset Play (DNPP).................33 MP3 player features Playing MP3 Files......................................34 File Search.................................................35 Folder Search ............................................35 Fast Forwarding and Reversing MP3 Play ...............................................36 Folder Select .............................................36 File / Folder Repeat ...................................37 Random Play .............................................37 Name Scroll for MP3.................................37 —2— Menu settings Menu System............................................38 Code Security Function .............................39 Touch Sensor Tone ....................................40 Manual Time Adjustment ..........................40 Calendar Adjustment.................................40 Calendar Mode..........................................40 Automatic Time Adjustment......................41 Disabled System Indicator (DSI)................41 Icon/Spectrum analyzer Select..................41 Font Select ................................................41 Dimmer .....................................................41 System Q ..................................................42 Switching preout .......................................42 Built-in Amp Mute Control ........................42 Switching Dual Zone System Output ........42 External Amp Control ................................42 News Bulletin Function with PTY News Timeout Setting ...........42 Local Seek Function ..................................43 Selecting Tuning Mode ..............................43 Auto Memory Entry ..................................43 AF (Alternative Frequency ) Function ........44 Restricting RDS Region (Region Restrict Function) .....................44 Auto TP Seek Function ..............................44 Monaural Reception ..................................44 Reading the MP3 ID3 tag .........................44 Text Scroll ................................................45 Power OFF Timer ......................................45 Built-in AUX Control ..................................45 Basic Operations of remote control ..................46 Installation Accessories ...............................................49 Installation Procedure................................49 Connecting Cables to Terminals ................50 Installation .................................................51 Troubleshooting Guide ................54 Specifications..............................59 Safety precautions 2WARNING 2CAUTION To prevent injury and/or fire, take the following precautions: To prevent damage to the machine, take the following precautions: • Insert the unit all the way until it is fully locked in place. Otherwise it may fly out of place during collisions and other jolts. • When extending the ignition, battery or ground cables, make sure to use automotive-grade cables or other cables with an area of 0.75mm2 (AWG18) or more to prevent cable deterioration and damage to the cable coating. • To prevent short circuits, never put or leave any metallic objects (e.g., coins or metal tools) inside the unit. • If the unit starts to emit smoke or strange smells, turn off the power immediately and consult your Kenwood dealer. • Make sure not to get your fingers caught between the faceplate and the unit. • Be careful not to drop the unit or subject it to strong shock. The unit may break or crack because it contains glass parts. • Make sure to ground the unit to a negative 12V DC power supply. • Do not open the top or bottom covers of the unit. • Do not install the unit in a spot exposed to direct sunlight or excessive heat or humidity. Also avoid places with too much dust or the possibility of water splashing. • Do not subject the faceplate to excessive shock, as it is a piece of precision equipment. • When replacing a fuse, only use a new one with the prescribed rating. Using a fuse with the wrong rating may cause your unit to malfunction. • To prevent short circuits when replacing a fuse, first disconnect the wiring harness. • Do not place any object between the faceplate and the unit. • During installation, do not use any screws except for the ones provided. The use of improper screws might result in damage to the main unit. • Do not apply excessive force to the open faceplate or place objects on it. Doing so will cause damage or breakdown. —3— IMPORTANT INFORMATION About the disc changer to be connected: To connect a disc changer having the "O-N" switch to this unit, set the "O-N" switch to "N". When you connect a model with no "O-N" switch, the converter cord CA-DS100 available as an option may be required. For details, consult your Kenwood dealer. If a model with no "O-N" switch is connected, some unavailable functions and information that cannot be displayed are generated, such as the DNPS, DNPP, Magazine random play, and CD Text display. Note that none of the KDC-C100, KDC-C302, C205, C705, and non-Kenwood CD changers can be connected. 2CAUTION You can damage both your unit and the CD changer if you connect them incorrectly. Do Not Load 8-cm (3-in.) CDs in the CD slot If you try to load an 8-cm CD with its adapter into the unit, the adapter might separate from the CD and damage the unit. English Safety precautions NOTE • If you experience problems during installation, consult your Kenwood dealer. • If the unit fails to operate properly, press the Reset button. The unit returns to factory settings when the Reset button is pressed. If the unit still fails to operate properly after the Reset button has been pressed, contact your local KENWOOD dealer for assistance. • Press the reset button if the CD auto changer is first controlled and operates incorrectly. The original operating condition will return. • The illustrations of the display and the panel appearing in this manual are examples used to explain more clearly how the controls are used. Therefore, what appears on the display in the illustrations may differ from what appears on the display on the actual equipment, and some of the illustrations on the display may represent something impossible in actual operation. • The functions that can be used and the information that can be displayed will differ depending on the external disc players being connected. Reset button • We strongly recommend the use of the Code Security function (page 39) to prevent theft. —4— Cleaning the Faceplate Terminals If the terminals on the unit or faceplate get dirty, wipe them with a dry, soft cloth. Cleaning the Unit If the faceplate of this unit is stained, wipe it with a dry soft cloth such as a silicon cloth. If the faceplate is stained badly, wipe the stain off with a cloth moistened with neutral cleaner, then wipe neutral detergent off. 2CAUTION Applying spray cleaner directly to the unit may affect its mechanical parts. Wiping the faceplate with a hard cloth or using a volatile liquid such as thinner or alcohol may scratch the surface or erases characters. Cleaning the CD Slot As dust can accumulate in the CD slot, clean it occasionally. Your CDs can get scratched if you put them in a dusty CD slot. The marking of products using lasers (Except for some areas) CLASS 1 LASER PRODUCT The label is attached to the chassis/case and says that the component uses laser beams that have been classified as Class 1. It means that the unit is utilizing laser beams that are of a weaker class. There is no danger of hazardous radiation outside the unit. Lens Fogging Right after you turn on the car heater in cold weather, dew or condensation may form on the lens in the CD player of the unit. Called lens fogging, CDs may be impossible to play. In such a situation, remove the disc and wait for the condensation to evaporate. If the unit still does not operate normally after a whilst, consult your Kenwood dealer. —5— English Handling Compact discs Playing a CD that is dirty, scratched or warped can cause the sound to skip and the unit to operate incorrectly, resulting in worsened sound quality. Take the following precautions to prevent your CDs from getting scratched or damaged. Handling CDs • Do not touch the recorded side of the CD (i.e., the side opposite the label) when holding it. Storing CDs Checking New CDs for Burrs • Do not store CDs in areas exposed to direct sunlight – such as a car seat or above the fascia panel (dashboard) – or other hot places. A CD-R or CD-RW is more susceptible than a music CD to damage from high temperatures and humidity, and in some cases, may become unusable if left in the car for long periods of time. • Remove CDs from the unit when not listening to them for a whilst, and put them back in their cases. Do not stack CDs that have been removed from their cases or prop them against something. Cleaning CDs • The reflective film on a CD-R or a CD-RW is more fragile than that on an ordinary music CD, and may peel off if scratched. Fingerprints on a CD-R or CD-RW are also more likely to cause skipping when the disc is played. For these reasons, handle the disc very carefully. Detailed handling instructions will appear on the CD-R or CD-RW package: read this information carefully before using the disc. If a CD has become dirty, wipe it off gently using a commercially available cleaning cloth or a soft cotton cloth, starting from the centre of the disc and moving outward. Do not clean CDs with conventional record cleaners, anti- static formulas, or chemicals such as paint thinner or benzene. • Do not stick tape on either side of the CD. Tape —6— When playing a new CD for the first time, check that there are not any burrs stuck to the perimeter of the disc or in the central hole. CDs with burrs stuck on them may not load properly or may skip whilst playing. Remove burrs using a ballpoint pen or a similar utensil. Burrs Burrs Do Not Load CD Accessories in Slot Do not use commercially available CD accessories that can be loaded into the CD slot, such as stabilisers, protective sheets, or CD cleaning discs, since they can cause the unit to malfunction. Do Not Use Special Shape CDs • Be sure to use round shape CDs only for this unit and do not use any special shape CDs. Use of special shape CDs may cause the unit to malfunction. Removing the CD Only remove the CD from the machine in a horizontal direction. You may damage the surface of the CD if you try pulling it down as it ejects. • Be sure to use CDs with disc mark only for this unit. • CD-Rs and CD-RWs which have not undergone finalization processing cannot be played. (For more information on finalization processing, refer to the manual for your CD-R/CD-RW writing software or CD-R/CD-RW recorder.) Additionally, depending on the recording status, it may prove impossible to play certain CDs recorded on CD-R or CD-RW. —7— Do Not Use CDs with Sticker on the Labelled Side Do not use the CD with the label sticker stuck on it. Using such a CD may cause the CD to be deformed and the sticker to peel off, resulting in malfunction of the unit. English Notes on playing MP3 files This unit can play MP3 files. Note, however, that the MP3 file recording media and formats acceptable are limited. When writing MP3 files, pay attention to the following restrictions. Acceptable media The MP3 file recording media acceptable to this unit are CD-ROM, CD-R, and CD-RW. Acceptable medium formats The medium formats acceptable to this unit are ISO 9660 Level 1 and Level 2 excluding the extended formats. When reading an MP3 file written in a format other than ISO 9660 Level 1 or Level 2, the unit may fail to play the file normally or display the file or folder name correctly. The major specifications of ISO 9660 Level 1 and Level 2 are as follows: • Maximum number of directory levels: 8 • Maximum number of files and folders per directory level: 253 (files and folders in total) • Characters available to file and folder names: A - Z, 0 - 9, _(underscore) • Maximum number of characters in file names : Level 1: 12 (including a separator "." and a 3-character extension) Level 2: 31 (including a separator "." and a 3-character extension) Settings for your MP3 encoder and CD writer When you use your MP3 encoder to compress audio data to an MP3 file, set the transfer bit rate of the encoder to fixed 128 kbps. When you use your CD writer to record MP3 files up to the maximum disc capacity, disable additional writing. For recording on an empty disk up to the maximum capacity at once, check Disc at Once. Entering ID3 tag Displayable ID3 tag is ID3 version 1 and 1.1; the character code is ASCII (see List of Codes).The ID3 tag versions 1 and 1.1 have the following size restrictions: • Album name: 30 bytes or less • Artist name: 30 bytes or less • Song title: 30 bytes or less Entering file and folder names When entering file and folder names, use the alphanumeric characters described above only. If you use any other character for entry, the file and folder names are not displayed correctly. They may neither be displayed correctly depending on the CD writer used. The unit recognizes and plays only those MP3 files which have the MP3 file name extension (.MP3). MP3 files should therefore be saved with the MP3 extension. Writing files into a medium When a medium containing MP3 data is loaded, the unit checks all the files on the medium. If the medium contains a lot of folders or non-MP3 files, therefore, it takes a long time until the unit starts playing MP3 files. In addition, it may take time for the unit to move to the next MP3 file or a file search or folder search may not be performed smoothly. You should not write non-MP3 files or unneeded folders along with MP3 files on the medium. 2CAUTION When playing MP3 files on a medium which also contains non-MP3 files or folders, observe the following precautions. Loading such a medium may produce loud noise to break the speakers. • Do no attempt to play a medium containing a non-MP3 file with the MP3 extension. The unit mistakes non-MP3 files for MP3 files as long as they have the MP3 extension. • Do not attempt to play a medium containing non MP3 file. MP3 file playing order When selected for play, folder search, file search, or for folder select, files and folders are accessed in the order in which they were written by the CD writer. Because of this, the order in which they are to be recorded does not match the order in which they are played. You may be able to set the order in which MP3 files are to be played by writing them onto a medium such as a CD-R with their file names beginning with play sequence numbers such as "01" to "99", depending on your CD writer. —8— For example, a medium with the following folder/file hierarchy is subject to folder search, file search, or folder select as shown below. Folder Virtual folder File Example of a medium's folder/file hierarchy (For a file search or folder search) Root Medium's virtual folder/file hierarchy for a folder select When a folder search is executed with file being played ... When a folder search is executed with file currently being played, the unit selects folders as shown below, starting with folder . Current album number Operation of the button FM Button AM Button ... ... When folder select is selected with file to move from folder to folder ... being played During folder select, a virtual folder is created one hierarchical level below each folder. The hierarchy is displayed as if the MP3 file recorded in each folder were placed in that virtual folder. When the unit enters the folder select mode with file being played, it selects folders as shown below, starting with folder (virtual folder ). Current album number Operation of the button 4 Button ¢ Button ... Level 1 Level 3 Level 2 Level 5 Level 4 Current track number being played ... Operation of the button ¢ Button 4 Button Beginning of track ... FM Button NOTE Level 1 Level 3 Level 5 Level 2 Level 4 When a file search is executed with file 6 AM Button ... ... • Each virtual folder is displayed with the original folder name bounded by parentheses " ( ) ". For example, the virtual folder below the folder named " 4 " is displayed with a name of " (4) ". The folder name of each virtual folder is displayed with up to 30 characters (in the ISO 9660 Level 2 format) or 8 characters (in the ISO 9660 Level 1 format). • The FM button is disabled in a folder because it has no subordinate hierarchical level below. Immediately after entering the folder select mode as in the above example, therefore, the FM button cannot be used as there is no hierarchical level below folder . Once you have moved to folder using the folder select function, for example, you can use the FM button to select folder one level below. —9— English General features Power Release button SRC/ PWR OFF Q u S.A/ ¢ 2ZONE FM Turning on the power: Press the SRC button. NOTE Turn the power on before carrying out the following procedures. Turning off the power: Hold down the PWR OFF button for one second or more. AUD 2ZONE DAB PWR OFF LOUD d DISP MENU NAME.S NOTE 4 ATT/ DISP LOUD The status of the Code Security Function (page 39) is displayed whenever the power is switched on. "CODE ON" : Security Code has been registered "CODE OFF" : Security Code has not been registered NF AM/ NF Volume Increasing Volume: Press the u button to turn up the volume. Decreasing Volume: Press the d button to turn down the volume. LOUD indicator Description about this indicator for these features can be displayed by setting the Lower Part Display (page 14) to "... + Function indicator". — 10 — Attenuator This function allows you to turn down the volume quickly. Turning Attenuator On/Off: Press the ATT button to switch the attenuator on and off. When the attenuator is off, the volume returns to the original level. NOTE Turning the volume up, or turning it all the way down deactivates the attenuator function. Switching Modes Switching Modes: Each time you press the SRC button, the mode switches as follows: ▼ Tuner mode ▼ CD/MP3 mode ▼ NOTE • The mode switches to the next mode from any mode which cannot be used. • The external disc control mode will differ depending on the unit that is connected. • You cannot use the AUX input function of the optional switching adapter KCA-S210A if this unit is connected with the KCAS210A. • If you have selected Standby mode, the timer function that turns the power off automatically will be activated. To find out how to set the time on the timer, and how to cancel the timer function, refer to the section on the Power OFF Timer function under Menu settings (page 45). The Power OFF Timer function is enabled only after the security code (page 39) is set up. NOTE Selecting AUX-name display Holding down the DISP button for two seconds or more during the AUX mode, AUX-name display is blinked for AUX-name selection mode. Pressing 4 or ¢ button during this mode allows you to select "TV", "VIDEO", "GAME" , "PORTABLE" , "DVD", or "AUX" in the AUX mode. The AUX-name selection mode can be exited by pressing the DISP button or doing nothing for 10 seconds. External disc control mode 1 ▼ External disc control mode 2 / AUX mode ▼ TV(AUX) ▼ Standby mode Selecting the standby mode: Press the SRC button repeatedly to select to "ALL OFF". When "ALL OFF" is displayed, the standby mode is turned on. The standby mode turns all functions off although leaving the unit’s power on. Use this mode when you want to have the display illuminated but do not want to listen to anything. Loudness This function amplifies low and high tones when the volume is turned down. The LOUD indicator lights up, when the loudness function is on. Turning Loudness On/Off: Hold down the LOUD button for one second or more to switch the loudness on and off. — 11 — English General features Switching Display Mode You can select the display mode of this unit. Changing the Display Mode: Each time you press the DISP button, the display mode switches as follows: "Display Type A" Divide the display into the upper and lower parts to separately provide different information. The upper part display The lower part display The Icon/ Spectrum analyzer "Display Type B" The display will turn on by using only the upper part of the display and clock. • You can switch the Icon/Spectrum analyzer. See "Icon/Spectrum analyzer Select" in the menu setting (page 41). • You cannot switch into the "Display Type C" during the standby mode. Switching the Upper Part Display This function switches the type of information on the upper part display when the display mode is "Display Type A" or "Display Type B" . 1 Press the S.A button to enter the display control mode. 2 Each time you press the 4 or ¢ button, the upper part display changes as follows: In Tuner mode: The upper part display Band display +Programme Service name(only during RDS station reception)/ Band display + Station frequency Clock "Display Type C" Use the entire display to provide a single type of information. Radio text (only during RDS station reception) Displaying Frequencies: Hold down the DISP button for one second or more. The frequency for the RDS station will be displayed for five seconds instead of the station name. The full screen display NOTE If the RDS station currently tuned to is transmitting no text whilst the Radio Text Display mode is turned on, "NO TEXT" will appear in the display. Whilst awaiting reception, "Waiting" will be displayed. NOTE • You can switch display information between the upper part display, lower part display, and full screen display. For further information, see "Switching the Upper Part Display" (page 12), "Switching the Lower Part Display" (page 14), "Switching FullScreen Display" (page 15) respectively. 2WARNING To prevent accidents, drivers should not look at the display whilst driving. — 12 — In CD/External disc control mode: Track Time Disc name (DNPS)(only when being preset) Disc Title (Units featuring CD text/MD only) Track Title (Units featuring CD text/MD only) • In the AUX mode, the Upper Part Display comes up with the AUX-name only, providing no cycle-through displays. 3 Press the S.A button to end the display control mode. NOTE • For display mode selection, see "Switching display mode" (page 12). • The same items cannot be selected for both the upper part and the lower part. In MP3 mode: Track Time Disc name (DNPS)(only when being preset) Folder name ID3 tag album name ID3 tag album name + ID3 tag artist name NOTE • You can give names to discs through the presetting disc name function (page 32). Note that depending on the unit, display may not be possible. • If you try to display the name of a disc that does not have one, "NO NAME" is displayed instead. • When there is an attempt to display the title of a disc for which the disc title/track title has not been recorded, "NO TEXT" is displayed for CD and "NO TITLE" is displayed for MD. • Depending on the type of characters of the CD Text, some characters may not be displayable. • If you don't turn the "Reading the MP3 ID tag" on, the ID3 tag will not be displayed. See "Reading the MP3 ID3 tag" in the menu setting (page 44). — 13 — English General features Switching the Lower Part Display In MP3 mode: This function switches the type of information on the lower part display when the display mode is "Display Type A". Spectrum Analyzer + Clock Date + Function indicator 1 Press the S.A button to enter the display control mode. 2 Each time you press the FM or AM button, the lower part Disc name (DNPS) (only when being preset) + Function indicator display changes as follows: In Tuner mode: File name + Function indicator ID3 tag song title + Function indicator Spectrum Analyzer + Clock Spectrum Analyzer Date + Function indicator Radio text (only during RDS station reception) + Function indicator In AUX mode: Spectrum Analyzer Spectrum Analyzer + Clock Date + Function indicator NOTE Spectrum Analyzer If the RDS station currently tuned to is transmitting no text whilst the Radio Text Display mode is turned on, "NO TEXT" will appear in the display. Whilst awaiting reception, "Waiting" will be displayed. NOTE 2WARNING • You can give names to discs through the presetting disc name function (page 32). Note that depending on the unit, display may not be possible. • If you try to display the name of a disc that does not have one, "NO NAME" is displayed instead. • When there is an attempt to display the title of a disc for which the disc title/track title has not been recorded, "NO TEXT" is displayed for CD and "NO TITLE" is displayed for MD. • Depending on the type of characters of the CD Text, some characters may not be displayable. • If you don't turn the "Reading the MP3 ID tag" on, the ID3 tag will not be displayed. See "Reading the MP3 ID3 tag" in the menu setting (page 44). To prevent accidents, drivers should not look at the display whilst driving. In CD/External disc control mode: Spectrum Analyzer + Clock Date + Function indicator Disc name (DNPS) (only when being preset) + Function indicator Disc Title (Units featuring CD text/MD only) + Function indicator Track Title (Units featuring CD text/MD only) + Function indicator Spectrum Analyzer 3 Press the S.A button to end the display control mode. — 14 — TEL Mute NOTE • For display mode selection, see "Switching display mode" (page 12). • If the display mode is set to "Display Type B", you can turn on or turn off the clock. • The same items cannot be selected for both the upper part and the lower part. Switching Full-Screen Display This function switches the type of information on the display when the display mode is "Display Type C". Each time you press the S.A button, the full screen display changes as follows: Demonstration Shut down the audio system temporarily whenever an incoming call is received. NOTE The function will not work if a cable is not connected to the car phone. When the telephone rings: When a call is received, "CALL" is displayed and all the unit functions are temporarily interrupted. Restoring Original Unit Source During Phone Call: Press the SRC button. "CALL" disappears from the display, and the volume of the original source is restored gradually. Turning TEL Mute Function Off After Phone Call: Hang the phone up. "CALL" disappears from the display. The original source (i.e., the one used before the phone call) is returned to automatically, and the volume restored gradually. Spectrum Analyzer 1 + Icon/Spectrum analyzer Spectrum Analyzer 2 + Icon/Spectrum analyzer Spectrum Analyzer 3 + Icon/Spectrum analyzer Spectrum Analyzer 4 + Icon/Spectrum analyzer Graphic 1 Graphic 2 NOTE • For display mode selection, see "Switching display mode" (page 12). • You can switch the Icon/Spectrum analyzer. See "Icon/Spectrum analyzer Select" in the menu setting (page 41). — 15 — English General features Switching Display during the Standby mode This function switches the type of information on the display in standby mode. 1 Press the SRC button repeatedly to select the standby mode. "ALL OFF" is displayed when the standby mode is selected. 2 Each time you press the S.A button, the display changes as follows: Demonstration (This is not available with the display mode set to "Display Type B") Date + Clock + Function indicator "ALL OFF" + Function indicator 2CAUTION • Do not apply excessive force to the faceplate bracket without attaching the faceplate. Doing so will cause the faceplate bracket to be deformed. • Do not touch the connector on the faceplate bracket after removing the faceplate. Touching the connector may cause damage to the unit. NOTE • The faceplate is a precision piece of equipment and can be damaged by shocks or jolts. For that reason, keep the faceplate in its special storage case whilst detached. • Do not expose the faceplate or its storage case to direct sunlight or excessive heat or humidity. Also avoid places with too much dust or the possibility of water splashing. Reattaching the Faceplate: 1 Hold the faceplate so that the control panel faces the front toward you and set the left side of the faceplate in the faceplate bracket. 2CAUTION Theft Deterrent Faceplate The faceplate of the unit can be detached and taken with you, helping to deter theft. Do not set the right side of the faceplate in the faceplate bracket first, when reattaching the faceplate. Doing so may cause the connector on the faceplate bracket to malfunction. 2 Press the right side of the faceplate until it locks. Removing the Faceplate: 1 Press the release button and drop open the faceplate. 2 Holding the centre part of the faceplate, pull it out. 3 Push upward the back of the faceplate bracket until it locks. System Q You can recall the best audio setting preset for different types of the music. — 16 — Switching the Preset Sound Setting: Each time you press the Q button, the preset sound setting switches as follows: Speaker setting mode Woofer setting mode Flat (Default setting) Rock Top 40 User memory* Scan of Flat – Easy Easy Jazz Pops 4 • In speaker setting mode Press either the 4 or ¢ button to select the type of speaker. The setting switches as follows. Off ("Speaker Setting OFF") / For 6x9/6 in. speaker ("Speaker Setting 6*9/6 inch") / For 5/4 in. speaker ("Speaker Setting 5/4 inch") / For the OEM speaker ("Speaker Setting O.E.M.") • In woofer setting mode Press either the 4 or ¢ button to select the type of Sub woofer. The setting switches as follows. "Woofer OFF" / "12in typeA" / "10in typeA" / "12in typeB" / "10in typeB" / "12in typeC" / "10in typeC" / "8inch" / "12in typeD" / "10in typeD" *User memory: The unit returns to the state adjusted the last time with the audio control setting feature. NOTE The System Q function changes the values of the following sound quality parameters: Bass centre frequency, bass level, bass quality factor, bass extend, middle centre frequency, middle level, middle quality factor, treble centre frequency, treble level non-fading level, highpass filter frequency for front output, high-pass filter frequency for rear output, and low-pass filter frequency for non-fading output. Their setting values are different depending on the setting of the speaker and woofer setting mode. 5 Press the Q button to end the speaker setting mode and woofer setting mode. NOTE • Speaker setting allows for tuning of bass, middle and treble. • Woofer setting allows for tuning of high-pass filter frequency, low-pass filter frequency and non-fading level. Speaker & Woofer setting Speaker setting allows the System Q settings to be fine-tuned according to the type of speakers. Woofer setting allows for Network configuration according to the type of subwoofers. Non-Fading Output You can turn the non-fading output on and off whilst the preout is switched to the non-fading preout. 1 Press the SRC button repeatedly to select the standby mode. "ALL OFF" is displayed when the standby mode is selected. 2 Press the Q button to enter the speaker setting mode. 3 Each time you press the FM/AM button, the mode switches as Turning non-fading output On/Off : Hold down the NF button for one second or more to set the function ON or OFF. "NF ON" is displayed when the non-fading output is set ON. follows: — 17 — English General features Audio control features Dual Zone System The following operation allows separate sound sources to control the output of the front and rear speakers. The Dual zone system can only be switched on when the source is set to the TV(AUX) mode. ¢ AUD Dual Zone System On/Off: Press the 2ZONE button for at least one second to switch the Dual Zone System on and off. "Zone 2 ON" is displayed when Dual Zone System is turned on. FM AUD 2ZONE DAB PWR OFF NOTE • You can select the speaker output, either front or rear, for the AUX input and the unit’s tuner or audio source. For details refer to "Switching Dual Zone System Output" (page 42) for the menu settings. • The Bass, Middle, Treble and Loudness adjustments do not affect the TV(AUX) channel. • When you set the Dual zone system to on whilst the non-fading preout is switched on, the sound of the non-fading preout does not be outputted. • If the Attenuator function is turned on while the Dual Zone System is enabled, the Attenuator is not applied to the TV(AUX) source. • The Dual Zone System function operates on the AUX source of this unit only. — 18 — LOUD DISP MENU NAME.S NF 4 Selecting mode Setting value AM Audio Control Setting Bass Centre Frequency Adjust various parameters of sound quality. Adjust the centre frequency of the bass. 1 Hold down the AUD button for one second or more to enter Display and setting: "Bass FRQ" : 60 / 70 / 80 / 100 (Only when the bass quality factor is set to 1.00, 1.25 or 1.50) / 150 (Only when the bass quality factor is set to 2.00) Hz. the control mode. 2 Selecting mode Press either the FM or AM button. Each time the button is pressed, the adjustment mode will change. Please refer to the following for the contents of the adjustment modes. NOTE Source tone memory Each source (CD, TV(AUX), FM, AM, and disc changer) has its own memory in which to store the bass, middle, treble and N-F level settings. The settings made for a particular source are then recalled automatically whenever you use that source (e.g., FM mode uses the tone settings made for FM, AM for AM, etc.). Bass Level Adjust the bass level. Display and setting: "Bass" : - 8 – + 8 3 Adjust each mode Press the 4/¢ button. Please refer to the following for the adjusting values. 4 Press the AUD button to end the control mode. NOTE • Determining the parameters in the audio control setting will clear all the adjustments made in the System Q and they are replaced with the values made in the audio control setting. • The following parameters can be set when the System Q function on the menu settings is ON. Bass centre frequency, bass quality factor, bass extend, middle centre frequency, middle quality factor, and treble centre frequency. Bass Quality Factor Adjust the Bass quality factor. Display and setting: "Bass Q" : 1.00 / 1.25 / 1.50 / 2.00 Bass Extend Switch the Bass Extend mode on/off. Display and setting: "Bass EXT" : ON / OFF (When the bass extend mode is set to on, low frequency response is extended by 20%.) — 19 — English Audio control features Middle Centre Frequency Treble Level Adjust the centre frequency of the middle. Adjust the treble level. Display and setting: "MID FRQ" : 0.5 / 1.0 / 1.5 / 2.0 kHz. Display and setting: "TRE" : - 8 – + 8 Middle Level Balance Level Adjust the middle level. Adjust the balance level. Display and setting: "MID" : - 8 – + 8 Display and setting: "Balance" : Left 15 – Right 15 Middle Quality Factor Fader Level Adjust the middle quality factor. Adjust the fader level. Display and setting: "Middle Q" : 1.0 / 2.0 Display and setting: "Fader" : Rear 15 – Front 15 Treble Centre Frequency Non-Fading Level Adjust the centre frequency of the treble. Adjust the Non-fading output level. Display and setting: "TRE FRQ" : 10.0 / 12.5 / 15.0 / 17.5 kHz Display and setting: "NF Level" : - 15 – + 15 NOTE • This mode is available only when the non-fading output function is set to on. • Not available during the Dual zone system is on. — 20 — High-pass Filter Frequency for Front Output Phase for Non-Fading Output Adjust the frequency of the High-pass filter for front output. Adjust the phase for Non-Fading output. Display and setting: "HPF Front" : Through / 40Hz / 60Hz / 80Hz / 100Hz / 120Hz / 150Hz / 180Hz / 220Hz Display and setting: "NF Phase" : Normal (0°) / Reverse (180°) NOTE NOTE • This mode is available only when the non-fading output function is set to on. • Not available during the Dual zone system is on. You can separately set the high-pass filter for front and rear output, including preouts. The high-pass filter does not affect the non-fading preout. Volume Offset High-pass Filter Frequency for Rear Output Set the sound level of the each source selected by adjusting the level difference between the basic sound level and the required level. Adjust the frequency of the High-pass filter for rear output. Display and setting: "HPF Rear" : Through / 40Hz / 60Hz / 80Hz / 100Hz / 120Hz / 150Hz / 180Hz / 220Hz Display and setting: "Volume Offset" : - 8 – ± 0 NOTE You can separately set the high-pass filter for front and rear output, including preouts. The high-pass filter does not affect the non-fading preout. Low-pass Filter Frequency for Non-Fading Output Adjust the frequency of the Low-pass filter for Non-Fading output. Display and setting: "LPF NF" : 50 Hz / 80 Hz / 120 Hz / Through NOTE • This mode is available only when the non-fading output function is set to on. • Not available during the Dual zone system is on. — 21 — English Tuner features Tuning ¢ SRC FM 1 Press the SRC button repeatedly until the tuner mode is obtained. "TUNER" is displayed only when the tuner mode is selected. 2 Press either the FM or AM button to select the band. Each time you press the FM button, the band switches between the FM1, FM2 and FM3. Press the AM button to select the MW and LW bands. AUD 2ZONE DAB PWR OFF LOUD DISP MENU NAME.S 4 #1-6 3 • Auto Seek Tuning (Auto1) NF Press the ¢ button to seek increasing frequencies. Press the 4 button to seek decreasing frequencies. • Preset station seek tuning (Auto2) Press the ¢ button to move to the next preset station (i.e., the one with the next highest number), and the 4 button to move to the last preset station (i.e., the one with the next lowest number). AM NOTE Band display Preset station number If the frequencies stored at the preset numbers receive stations which were not originally memorized when travelling long distances, the preset number is not displayed. In such cases, pressing the 4/¢ button to use preset station seek will receive channel 1. • Manual Tuning (Manual) Press the ¢ button to increase the frequency by one step. Press the 4 button to decrease the frequency by one step. Frequency NOTE • The ST indicator lights up when stereo broadcasts are being received. • Please see the menu settings about selecting tuning mode. (page 43) ST indicator Description about this indicator for these features can be displayed by setting the Lower Part Display (page 14) to "... + Function indicator." Station Preset Memory Store the frequency of the station currently being listened to. You can then recall that station with a single touch of a button. — 22 — 1 Select the band/station that you want to have stored. 2 Hold down the button (#1-6) that you want to use for the Preset station seek with Programme service name (Function of Remote Control) station, for two seconds or more. The button number blinks once in the display to indicate that the data has been stored. Recalling a Preset Station: Press the preset station button (#1-6) for the desired station. The number of the recalled station is displayed. You can search for the preset station with Programme Service name. 1 Press the DNPP button on the remote control. "SNPP" will be displayed once the seek mode is entered. The names of the stations preset in the band currently listened to are displayed for 5 seconds each. The display band switches in the following order: = FM1 Ô FM2 Ô FM3 Ô AM + NOTE You can store 6 stations in each of the FM1, FM2, FM3, and AM (MW and LW) bands. Each time you press the ¢ button, the station display switches in the forward direction. Each time you press the 4 button, the station display switches in the reverse direction. Stations which have no names will be displayed as frequencies. Direct Access Tuning (Function of remote control) When you know the frequency of the station that you want to listen to, you can input it directly for quick access. 1 Select the band by pressing the FM or AM button. 2 Press the DIRECT button. "----" is displayed for 10 seconds. If you make no input in the 10-second period, direct access tuning is automatically cancelled. 3 Enter the frequency of the desired station. If you want to listen to an FM station at 92.1 MHz, for example, press 0, 9, 2, and 1. If you want to listen to an AM station at 810 kHz, for example, press 0, 8, 1, and 0. NOTE NOTE Changing the Displayed Band Pressing the FM button switches between the FM1, FM2, FM3 and AM displays, in that order. Pressing the AM button switches between the displays in the reverse direction. 2 Once the name is displayed for the station you want to listen to Press the OK button. Reception starts of the displayed station, and the seek mode ends. Cancelling mode during input: Press the DNPP button. The seek mode is cancelled. • You cannot enter frequencies above or below what a band can receive. • FM frequencies can only be input in 0.1 MHz steps, and not 0.01MHz steps. Cancelling Direct Access Tuning: Press the DIRECT button again. — 23 — English RDS features RDS (Radio Data System) ¢ RDS is a digital information system that lets you receive signals besides those of regular radio programmes, such as network information being transmitted from radio stations. When listening to an RDS station (ie, a station with RDS capability), the programme service name of the station is displayed along with the frequency, advising you quickly which station is being received. RDS (Radio Data System) stations also transmit frequency data for the same station. When you are making long trips, this function automatically switches to the particular frequency with the best reception for the particular network of stations that you want to listen to. The data is automatically stored, allowing you to switch quickly to another RDS stations, broadcasting the same programme, that has better reception. These include stations stored in the station preset memory that you often listen to. FM AUD 2ZONE DAB PWR OFF LOUD DISP MENU NAME.S DISP 38 #1-6 NF 4 AM TI/ TI VOL ADJ Enhanced Other Network Stations that offeralso transmit information about other RDS stations that have traffic information. When you are tuned to a station that is not transmitting traffic information, but another RDS station starts transmitting a traffic bulletin, the tuner automatically switches to the other station for the duration of the bulletin. Programme Service name Radio text TI indicator Alarm Description about this indicator for these features can be displayed by setting the Lower Part Display (page 14) to "... + Function indicator." When an emergency transmission (announcing disasters, etc.) is sent, all current functions are interrupted to allow the warning to be received. — 24 — Traffic Information Function Presetting Volume for Traffic Information/News You can listen to traffic information. If you are listening to tapes or discs, they will continue playing until a traffic bulletin is broadcast. Turning TI function On/Off: Press the TI button to turn the function on and off. When the function is on, the TI indicator is turned on. When none is being received, the TI indicator will blink on and off. When a traffic information station is being received, the TI indicator will turn on. When a traffic bulletin begins to be broadcast, "Traffic Info" will be displayed, and reception will begin at the preset volume. If you are listening to a tape or disc when a traffic bulletin begins, they will automatically be turned off. When the bulletin ends or poor reception is experienced, the tape or disc will begin playing again. NOTE Pressing the TI button whilst in the MW/LW band automatically switches reception to the FM band. However, the MW/LW band is not returned to when the TI button is pressed again. Switching to a Different Traffic Information Station: Use the 4 / ¢ buttons to make an auto seek of the TI stations in a certain band. Preset the volume level to be used for traffic information and news broadcasts. 1 Tune into the station for which you want to set the volume. 2 Adjust the volume to the desired level. 3 Hold down the TI VOL ADJ button for two seconds or more. The volume level blinks once in the display to indicate that the data has been stored. Future traffic information/news broadcasts are heard at the preset level. NOTE • The volume cannot be lowered by this function during tuner reception. The volume is only set when it is louder than the listening volume of the tuner. • You can arrange only to listen to traffic information or news bulletins with at preset volume with the volume set at minimum. NOTE • When you are listening to a tape or disc, you cannot change to another TI station. • When the auto TP seek function is turned on and reception starts to weaken, the tuner automatically seeks traffic information stations with better reception. • If you are tuned to a station that is not a traffic information station itself but which provides services, you can still have traffic information received. • Holding down the TI button for one second or more when the TI function is on in the disc mode results in a change to the programme service name or frequency display of the traffic information station for five seconds. — 25 — English RDS features 24. Jazz Music (Jazz Music) 25. Country Music (Country Music) 26. National Music (National Music) 27. Oldies Music (Oldies Music) 28. Folk Music (Folk Music) 29. Documentary (Documentary) (Speech.....1~9,16~23, 29, Music.....10~15, 24~28) • You can select the type of programme directly by pressing a preset button. The buttons are factory-set to the following type of programmes: 1. Music 2. Speech 3. News 4. Other Music 5. Serious Classical 6. Varied Programme Type (PTY) Function Conduct auto seek tuning only on those stations with selected kinds of programmes. 1 Press the 38(PTY) button. "PTY Select" is displayed, and the Programme Type Selection (PTY) Mode entered. If you make no key input in 30 seconds, the mode will automatically turn off. NOTE You cannot use this function whilst the traffic bulletin is received. 2 Select the type of programme to be received • Press either the FM or AM button repeatedly until the type of programme you want to listen to. The selection includes: Speech (All Speech) Music (All Music) 1. News (News) 2. Current Affairs (Current Affairs) 3. Information (Information) 4. Sports (Sport) 5. Education (Education) 6. Drama (Drama) 7. Culture (Cultures) 8. Science (Science) 9. Varied (Varied Speech) 10. Pop Music (Pop Music) 11. Rock Music (Rock Music) 12. Easy Listening Music (Easy Listening M) 13. Light Classical (Light Classic M) 14. Serious Classical (Serious Classics) 15. Other Music (Other Music) 16. Weather (Weather & Metr) 17. Finance (Finance) 18. Children’s programmes (Children's Prog) 19. Social Affairs (Social Affairs) 20. Religion (Religion) 21. Phone In (Phone In) 22. Travel (Travel & Touring) 23. Leisure (Leisure & Hobby) NOTE Changing the Preset Button Settings for Programme Type After selecting the type of programme to be stored in a certain preset button, hold down that button for two seconds or more. The previously stored data for that button are erased and the new programme type is stored. 3 Seeking the selected programme type Press the 4 or ¢ button to make a seek of frequencies with your selected type of programme. The display blinks and the seek starts. If your selected type of programme is found, the name of the station is displayed and the station is tuned into. "PTY Found" is displayed for about 30 seconds. If you make no key input in 30 seconds, the PTY selection mode will turn off automatically. NOTE If no programme can be found, "NO PTY" is displayed. If you want to select another type of programme, repeat steps 2 and 3 above. Switching to Other Stations with the Same Type of Programme: When "PTY Found" is displayed, perform auto seek tuning. The tuner scans for another station with the same type of programme. Cancelling Programme Type Function During Its Operation: Press the 38(PTY) button. — 26 — in one scrolling display of the text. To scroll automatically: 1 Display the radio text referring to the "Switching the Upper Part Display" (page 12) or "Switching the Lower Part Display" (page 14). The text will be displayed in one scrolling display. 2 Holding down the DISP button for one second or more with radio text displayed on the upper part display scrolls the text once. Changing Language for Programme Type(PTY) Function Changing the display language to another language. 1 Press the 38(PTY) button. "PTY Select" is displayed, and the Programme Type Selection (PTY) Mode entered. 2 Enter the Changing Language Mode Press the DISP button to enter the changing language mode. NOTE 3 Changing the Display Language • Please see the menu settings (page 45) about switching between manual scrolling and automatic scrolling. • You can scroll text when "Display Type A" or "Display Type B" has been selected by the switching display mode function. For display mode selection, see "Switching display mode" (page 12). Press the FM or AM button. Each time the button is pressed, the display language will change as follows: English German Spanish Swedish French Portuguese Dutch Norwegian 4 Press the DISP button to end the changing language mode. Radio Text Scroll This function permits the text to be scrolled and the entire text to be displayed. The scrolling method differs depending on the setting of scrolling in the menu. To scroll manually: 1 Display the radio text in upper part display, referring to "Switching the Upper Part Display" (page 12). 2 Holding down the DISP button for one second or more results — 27 — English CD/External disc control features Playing CDs Release button SRC ¢ DISC+ AUD 2ZONE DAB PWR OFF LOUD DISP MENU NAME.S DISP/ NAME.S Disc number IN indicator REP SCAN M.RDM 38 2CAUTION When inserting a CD, make sure the CD has been completely drawn in before pushing back the faceplate. Failing to do so might scratch the CD. Playing CDs Already Inserted: Press the SRC button repeatedly until the CD mode is obtained. "CD" is displayed when the CD mode has been selected. The CD will start playing. Pausing and Restarting CD Play: Press the 38 button to make the disc pause. Press the same button again to start play again. Eject: Press the release button and drop open the faceplate. Press the 0 button located near the CD slot. The CD stops playing and ejects from the slot. Push back the faceplate with your hand until it locks. NF 4 DISC- RDM Track number Playing CDs: A press of the release button causes the faceplate to drop to the front, thereby exposing the CD slot. Holding the CD with the labeled side facing up, insert it in the slot. The CD will start playing. Push back the faceplate with your hand until it locks. The IN indicator will light when a CD has been inserted. Track time Disc title/Track title/DNPS 2CAUTION Description about this indicator for these features can be displayed by setting the Lower Part Display (page 14) to "... + Function indicator". • Do not attempt to insert a CD into the slot if another one is already there. — 28 — • The unit can only play 12-cm (5-inch) CDs. If you insert an 8-cm (3-inch) CD, it will get stuck inside and can cause the unit to malfunction. • When the faceplate has been dropped open, it might interfere with the gear lever or something else. If this happens, pay attention to safety and move the gear lever or take an appropriate action, then operate the unit. • Do not apply excessive force to the open faceplate or place objects on it. Doing so will cause damage or breakdown. • Do not use the unit with the faceplate in the open condition. Doing so will cause breakdown. NOTE When one disc has finished playing its last track, the next disc in the changer starts playing. When the last disc in the changer has finished, the player returns to the first disc and starts playing it. Fast Forwarding and Reversing Disc Play NOTE When you load a CD and eject it right away, the next time you try to insert the CD may not load. In such a situation, take the CD out for a moment and then reinsert it. Fast Forwarding Disc Play: Hold down on the ¢ button. Release your finger to play the disc at that point. Reversing Disc Play: Hold down on the 4 button. Release your finger to play the disc at the point. NOTE Playing Other Disc mode This function permits the connection of optional players and the playing of discs other than the loaded CD (in the current unit). You cannot use reverse play between tracks depending on the model being connected. Instead, the reverse play function is cancelled when it reaches the beginning of a track, at which point normal play automatically resumes. Playing Discs: Press the SRC button repeatedly to select the external disc control mode. The disc will start playing. NOTE The external disc control mode will differ, depending on the unit that is connected. Mode Display Examples • "CD2"...when a CD player is connected • "CD-CH"/"MD-CH"/"DISC"...when a disc changer is connected • "CD-CH1"/"MD-CH1"/"DISC1", "CD-CH2"/"MD-CH2"/"DISC2" ...when two disc changers are connected Pausing and Restarting Disc Play: Press the 38 button to make the disc pause. Press the same button again to start play again. — 29 — English CD/External disc control features Each time the button is pressed, the displayed disc number increases by one. Play starts at the beginning of the displayed disc. Track Search Search forwards or backwards through the tracks on the disc until you reach the one that you want to listen to. NOTE Making a Reverse Track Search: Press the 4 button to display the desired track number. Press once to search back to the beginning of the current track, twice to search back to the beginning of the previous track, and so forth. Play starts at the beginning of the displayed track number. NOTE (For disc changers) Pressing the 4 button whilst listening to track 1 only searches back to the beginning of that track. The reverse search is not "recycled" to the last track on the disc. Making a Forward Track Search: Press the ¢ button to display the desired track number. Press once to fast forward to the next track, twice to fast forward to the track after that, and so forth. Play starts at the beginning of the displayed track number. "Load" is displayed when discs are being exchanged on the disc changer. Track / Disc Repeat Repeat playing the current track or disc. Turning Repeat Play Function On/Off: Press the REP button to switch the repeat play function on and off as follows : ▼ Track Repeat ON ▼ Disc Repeat ON (Function of disc changers) NOTE (For disc changers) You cannot make a forward track search when listening to the last track on a disc. ▼ Repeat OFF "Track Repeat ON"/"Repeat ON" is displayed and the track number blinks in the display when track repeat is on. "Disc Repeat ON" is displayed and the disc number blinks in the display when disc repeat is on. Disc Search (Function of disc changers) Search forwards or backwards through the discs in a disc changer until you reach the one that you want to listen to. Making a Reverse Disc Search: Press the DISC– button to display the desired disc number. Each time the button is pressed, the displayed disc number decreases by one. Play starts at the beginning of the displayed disc. Making a Forward Disc Search: Press the DISC+ button to display the desired disc number. NOTE Repeat play is cancelled when you eject the disc. Track Scan Successively play the beginning of each track on a disc until you find the track that you want to listen to. — 30 — Starting the Track Scan: Press the SCAN button. "Scan ON" is displayed and the first 10 seconds of each track are played, and the tracks are played in order. The track number currently being heard blinks in the display. Stopping to Listen to the Track Being Scanned: Press the 38 or SCAN button again to stop the scan and keep on listening to a track normally. Magazine Random Play (Function of disc changers) Play the tracks on all the discs in the disc changer in random order. 1 Press the M.RDM button to switch the magazine random play function on and off. "M.Random ON" is displayed when magazine random play is turned on. The display of the disc and track numbers change continuously as the next track is being selected. When the disc/track has been selected, play starts. The selected disc/track number blinks in the display as it is being played. NOTE The track scan function is cancelled when you eject the disc. 2 To change the track being heard, press the ¢ button. Another disc/track is selected and played. Random Play NOTE Play all the tracks on the current disc in random order. • Magazine random play is cancelled when you eject the disc. • The time needed for random selection depends on the number of discs loaded in the disc magazine. 1 Press the RDM button to switch the random play function on and off. "Random ON" is displayed when random play is turned on. The display of the track number changes continuously as the next track is being selected. When the track has been selected, play starts. The selected track number blinks in the display as it is being played. NOTE (For disc changers) When all the tracks on a certain disc have been played using the random play function, the next disc on the changer starts playing (with the random play function still turned on). 2 To change the track being heard, press the ¢ button. Another track is selected and played. NOTE Random play is cancelled when you eject the disc. — 31 — English CD/External disc control features Text Scroll This function permits the text to be scrolled and the entire text to be displayed. The scrolling method differs depending on the setting of scrolling in the menu. To scroll manually: 1 Display the disc or track title in the upper part display, referring to "Switching the Upper Part Display" (page 12). • The Disc Name Preset function cannot be used during the Magazine random play as well as while a disc title or track title is displayed in the upper part display. • The Disc Name Preset function cannot be used while folder name or ID3 tag(Artist, Album) is displayed in the upper part display. 2 Press the NAME.S button for at least two seconds. "NAME SET" is displayed and the disc name preset mode is entered. The cursor blinks in the position where character input can be made. 2 Holding down the DISP button for one second or more results in one scrolling display of the titles. To scroll automatically: 1 Display the disc or track title referring to the "Switching the Upper Part Display" (page 12) or "Switching the Lower Part Display" (page 14). The titles will be displayed in one scrolling display. 3 Press either the 4 or ¢ button to move the cursor to the desired position. The 4 button moves the cursor to the left, and the ¢ button to the right. You can also move the cursor left or right by pressing the 4 or ¢ buttons, respectively, on the remote control. 2 Holding down the DISP button for one second or more results in one scrolling display of the titles. 4 Each press of the 38 button results in the type of characters that are to be entered changing between alphabet and numerals/symbols. Press the DISC+ or DISC– button to display the desired character. Characters that can be displayed are as follows. NOTE • Please see the menu settings (page 45) about switching between manual scrolling and automatic scrolling. • You can scroll text when "Display Type A" or "Display Type B" has been selected by the switching display mode function. For display mode selection, see "Switching display mode" (page 12). • You cannot use the text scroll function during magazine random play. Alphabet (upper case): A ~ Z Alphabet (lower case): a ~ z Numerals and symbols: 0~9 @ ” ‘ ` % & * + - = , . / \ < > [ ] Special characters: á à é è í ì ó ò ú ù Ñ Ç ® ß ‹ fl â ä ê ë î ï ô ö û ü ñ ç © Æ › fi Presetting Disc Names (DNPS) Store the names of discs to be displayed when played. 1 Play the disc whose name you want to preset. NOTE • This function is not available for disc changers that do not feature the Disc Name Preset function. NOTE Direct Alphabet Input (Function of remote control with number/letter entry buttons) You can directly input letters using the number/letter entry buttons on the remote control. Example: Use the following table to enter the name "DANCE". — 32 — Character Button to press # Times pressed “D” #3 1 Disc Name Preset Play (DNPP) (Function of Remote Control) “A” #2 1 “N” #6 2 If you have preset the name of a disc that you want to listen to in the disc changer, you can look for it by name and start playing it. “C” #2 3 1 Press the DNPP button on the remote control. “E” #3 2 "DNPP" will appear in the display, and the disc name preset play mode is entered. The names of all the discs in the disc changer will appear successively in the display for five seconds each. Discs whose names have not been preset will appear as "NO NAME" in the display. 5 Continue steps 3 and 4 until all the characters are chosen for the name. NOTE NOTE You can enter up to 12 characters for each name. 6 Press either the NAME.S button on the main unit or the OK button on the remote control. The disc name is stored and the disc name preset mode is cancelled. If you make no entry in a 10-second period, the name will be stored with the characters input so far. NOTE • You cannot store the names of the discs in the MDs. • The number of discs whose names can be stored will differ depending on the disc changer that is connected. Please see your disc changer manual for details. Up to 30 CDs can be registered with this unit. • Discs are identified by their total length and number of tracks. If another disc happens to have the same specifications as one that you have already stored a name for, the name will be displayed for it, too. • If you want to change the name of a disc, repeat steps 1 and 2 to display the name, and then repeat steps 3 and 4 to input the changes. • Pressing the reset button erases the disc names stored in this unit, but does not erase the names stored in a disc changer. • MP3 recorded media allows you to register a single media name only. Registration for each CD as it is available with the CD cannot be achieved. • This function can only be used in disc changers that were manufactured or sold as of 1997. Also note that some units cannot provide a display unless the disc name preset has been made by the unit that is playing. • Discs in the disc changer that have never been played before will appear as "NO ACCESS" when the disc names are displayed. When you cannot identify a disc because of the "NO ACCESS" display after inserting a disc magazine, try playing it to display the disc name. Also note that "NO DISC" will be displayed when a disc has not been loaded. Rapid display (forward / reverse): Press the DISC+ or DISC– button. Pressing the DISC+ button will rapidly display the preset names/disc titles in order. Pressing the DISC– button will rapidly display the preset names/disc titles in reverse order. 2 When the name appears for the disc you want to play Press the OK button. The disc whose name is displayed will be recalled, and the disc name preset play (DNPP) mode will end. To cancell DNPP mode: Press the DNPP button. The disc name preset play (DNPP) mode will be cancelled. — 33 — English MP3 player features Playing MP3 Files Release button SRC ¢ Play: A press of the release button causes the faceplate to drop to the front, thereby exposing the CD slot. Holding the media with the labeled side facing up, insert it in the slot. The media will start playing. Push back the faceplate with your hand until it locks. The IN indicator will light when a media has been inserted. FM AUD 2ZONE DAB PWR OFF LOUD DISP MENU NAME.S DISP #2 file number IN indicator 38 #3/ REP RDM 2CAUTION When inserting a media, make sure the media has been completely drawn in before pushing back the faceplate. Failing to do so might scratch the media. Playing Media Already Inserted: Press the SRC button repeatedly to select the CD mode. "CD" is displayed when the CD mode has been selected. The media will start playing. Pausing and Restarting Media Play: Press the 38 button to make the media pause. Press the same button again to start play again. Eject: Press the release button and drop open the faceplate. Press the 0 button located near the CD slot. The media stops playing and ejects from the slot. Push back the faceplate with your hand until it locks. NF 4 AM Track time file name/ ID3 tag song title/ DNPS 2CAUTION Description about this indicator for these features can be displayed by setting the Lower Part Display (page 14) to "... + Function indicator". • Do not attempt to insert a media into the slot if another one is already there. — 34 — • When the faceplate has been dropped open, it might interfere with the gear lever or something else. If this happens, pay attention to safety and move the gear lever or take an appropriate action, then operate the unit. • Do not apply excessive force to the open faceplate or place objects on it. Doing so will cause damage or breakdown. • Do not use the unit with the faceplate in the open condition. Doing so will cause breakdown. NOTE It may take time for the file search depending on the number of files and the state of the folder hierarchy. Folder Search NOTE • When you load a media and eject it right away, the next time you try to insert the media may not load. In such a situation, take the media out for a moment and then reinsert it. • The MP3 media that this unit can play are CD-ROM, CD-R, and CD-RW. The medium formats must be ISO 9660 Level 1 or Level 2. The methods and precautions to be followed for writing MP3 files are covered in "Notes on playing MP3 files" (page 8). Check that section before creating your MP3 media. • It takes time for the unit to check each medium to see if it contains any MP3 file before it starts playing the medium. File Search Search forward or backward through the files on the media until you reach the one that you want to listen to. Making a Backward File Search: Press the 4 button to display the desired file number. Press once to search back to the beginning of the current file, twice to search back to the beginning of the previous file, and so forth. Play starts at the beginning of the displayed file number. Making a Forward File Search: Press the ¢ button to display the desired file number. Press once to fast forward to the next file, twice to fast forward to the file after that, and so forth. Play starts at the beginning of the displayed file number. Search forward or backward through the folders on the media. Making a Backward Folder Search: Press the AM button. Pressing the button moves back to the previous folder. The unit plays the medium starts at the beginning of the selected folder. If the selected folder contains no MP3 file, the unit automatically plays the file nearest to that folder in the MP3 file playing order. Making a Forward Folder Search: Press the FM button. Pressing the button moves to the next folder. The unit plays the medium starts at the beginning of the selected folder. If the selected folder contains no MP3 file, the unit automatically plays the file nearest to that folder in the MP3 file playing order. NOTE It may take time for the folder search depending on the number of files and the state of the folder hierarchy. — 35 — English MP3 player features Fast Forwarding and Reversing MP3 Play Displays the current folder name. Fast Forwarding MP3 Play: Hold down on the ¢ button. Release your finger to play the MP3 at that point. Reversing MP3 Play: Hold down on the 4 button. Release your finger to play the MP3 at the point. Displays the hierarchical level of the current folder. NOTE • If you reach the beginning of the file with the fast reverse, the player enters the pause state. If you release the button, the music begins to play. • During the fast forwarding and reversing process, audible tone and time code display are disabled. • Time code may be different between the states before and after the fast forwarding and reversing operations. • The time code for the first few seconds on pressing the button may be unchanged. • The time code variation may be large if a file is encoded in variable bit rate (VBR). Folder Select You can use this function to select the folder containing the sound file you want be played. 1 Enter the Folder Select Mode Pressing the #2 button enters the folder select mode. The display reads as shown below. Displays the number in the folder belonging to the currently selected folder. NOTE The unit cannot enter the folder select mode if the loaded medium contains no folder recorded. 2 Selecting the desired folder • You can move from folder to folder at the same hierarchical level: Press the ¢ button to move to the next folder at the same hierarchical level. Press the 4 button to move to the previous folder at the same hierarchical level. • You can select the hierarchical level of the folder: Press the FM button to move down one level in the folder hierarchy. Press the AM button to move up one level in the folder hierarchy. • You can return to the first hierarchical level (Root Jump): Press the #3 button to return to the folder at the top hierarchical level on the medium currently being played. NOTE The methods for moving to other folders in the folder select mode are different from those in the folder search mode. See "Notes on playing MP3 files" (page 8) for details. — 36 — 2 To change the file being heard, press the ¢ button. 3 When you have found a desired folder Press either the #2 or 38 button. This ends the folder select mode and starts playing the first MP3 file in the selected folder. Another file will be selected and played. NOTE Random play is cancelled when you eject the media. NOTE • If the folder selected after leaving the folder select mode contains no MP3 file, the unit plays the MP3 file nearest to that folder in the MP3 file playing order. • During the folder select mode, no audible sound is produced. File / Folder Repeat Repeat playing the file or the folder currently being listened to. Turning Repeat Play On/Off: Press the REP button to switch repeat file/folder play on and off as follows: ▼ File Repeat ON ▼ Folder Repeat ON ▼ File/Folder Repeat OFF "File Repeat ON" is displayed when file repeat is on. "Folder Repeat ON" is displayed when folder repeat is on. Name Scroll for MP3 This function permits the folder/file name and ID3 tag(Song title, Artist, Album) to be scrolled and the entire name to be displayed. The scrolling method differs depending on the setting of scrolling in the menu. To scroll manually: 1 Display the folder name or ID3 tag (artist name, album name) in the upper part display, referring to "Switching the Upper Part Display" (page 12). 2 Pressing the DISP button for at least one second results in one scrolling display of the names. To scroll automatically: 1 Display the folder/file name or ID3 tag (song title, artist name, album name), referring to "Switching the Upper Part Display" (page 12) or "Switching the Lower Part Display" (page 14). The display of the name will be scrolled repeatedly. 2 Pressing the DISP button for at least one second results in one NOTE Repeat play is cancelled when you eject the media. Random Play Play all the files on the current folder in random order. scrolling display of the names. NOTE • Please see the menu settings (page 45) about switching between manual scrolling and automatic scrolling. • You can scroll the names when "Display Type A" or "Display Type B" has been selected by the switching display mode function. For display mode selection, see "Switching display mode" (page 12). 1 Press the RDM button to switch random play on and off. "Random ON" is displayed when random play is turned on. When the file has been selected, play will begin. — 37 — English Menu settings Menu System SRC ¢ FM You can set the defaults for additional functions in the menu mode. Make a setting for each function, referring to the following operations. 1 Enter the menu mode Hold down the MENU button for one second or more. "MENU" is displayed when the menu mode is entered. The function that you can adjust is indicated with the current settings displayed. AUD 2ZONE DAB PWR OFF LOUD DISP MENU NAME.S DISP MENU #1-6 2 Selecting function to set NF 4 Press the FM button to search through the functions until you see the one you want to adjust in the display. Press the AM button to search through the functions backward. Function items change in the order of features that follow in the menu system. Example: If you want to switch the setting of the touch sensor tone function from on to off, first search through the functions until you see "Beep ON" in the display. AM 3 Changing setting for currently displayed function Press either the 4 or ¢ button. The setting will change for each function. Example: The setting of the touch sensor tone will switch from on to off, and "Beep OFF" is displayed. Menu display 4 Ending the menu mode Press the MENU button. NOTE NEWS indicator RDS indicator Make sure to end the menu mode when finished. If you fail to end the menu mode, several functions may not operate properly, including the Traffic Information function, the News Bulletin function with PTY news timeout setting, and the Alarm function. — 38 — "RE-ENTER" will appear in the display for one second, asking you to enter the code once again for confirmation. When "CODE" appears in the display, you can start inputting the code. Code Security Function After a security code has been registered, power cannot be restored if the battery is disconnected from the unit unless the code is first input. NOTE All the steps in this procedure (1 through 7) must be completed before the code security function can be turned on. However, once the procedure is finished, it need not be repeated. Once the code security function has been activated, "Security" disappears from the MENU system. Note that it will no longer be possible to cancell this function afterwards. 1 Press the SRC button repeatedly to select the standby mode. "ALL OFF" is displayed when the standby mode is selected. 2 Hold down the MENU button for one second or more. "MENU" is displayed first and then "Security" is displayed. 3 Hold down either the 4 or ¢ button for one second or more. "ENTER" will appear in the display for one second, indicating the code setting mode has been entered. When "CODE" appears in the display, you can start inputting the code. 6 Press the Preset button and input the security code again. 7 Hold down the DISP button again for three seconds or more. "APPROVED" will appear in the display, with the code security function turning on. From this point on, if the unit is disconnected from the battery, the security code must be entered the first time that the unit's power is turned on. "ENTER" and "CODE" will appear in the display, asking you to input the code. NOTE If you input an incorrect security code, the code setting mode will be cancelled automatically. Follow the steps from 3 to 7 above again. If you press the RESET button or remove the battery: The first time you turn the unit on again, "CODE" will appear in the display, asking you to input the security code. Repeat steps 6 and 7 above, and input the security code. You can start operating the unit again when "APPROVED" appears in the display. NOTE 4 Press the preset button and enter your security code. Use the security code shown on your Car Audio Passport. Example: Enter "3510" as your code, pressing the buttons as follows: Step Button to press # Times pressed Display 1 #1 4 “3” 2 #2 6 “5” 3 #3 2 “1” 4 #4 1 “0” If you enter the wrong code, "Waiting" is displayed and you cannot make further input of the code for a fixed interval (see table below), which grows longer each time you enter the wrong code. When "CODE" is displayed, you can make input again. 5 Hold down the DISP button for three seconds or more. The security code will be set. Number of wrong inputs Interval until next input is allowed 1 2 3 4 5 minutes 1 hour 24 hours The number of wrong inputs is displayed. — 39 — English Menu settings Touch Sensor Tone Calendar Adjustment This function produces a beep sound that accompanies button operation. It can be switched on or off. Adjust the date for the unit so that you can use the calendar function. Display and setting: "Beep ON" : Beep setting is on. (Default setting) "Beep OFF" : Beep setting is off. Display and setting: 1 Select the display "Date Adjust" during the selecting function in the menu system. NOTE The beep sound is not output from the preout jacks. 2 Hold down either the 4 or ¢ button for one second or more to enter the Calendar adjustment mode. The date display will blink. 3 Selecting the item (day, month, or year) to adjust Press the 4 or ¢ button. The item blinking in the display can be adjusted. Manual Time Adjustment 4 Adjusting the date Press the FM or AM button. The item of the date blinking in the display will change. Adjust the time manually. NOTE This adjustment is available only when the automatic time adjustment is set to off. (page 41) Display and setting: 1 Select the display "Clock Adjust" during the selecting function in the menu system. 2 Hold down either the 4 or ¢ button for one second or more to enter the Manual time adjustment mode. The time display will blink. 3 • Adjusting the hours Press the FM button to advance the hours, or press the AM button to make the hours go back. • Adjusting the minutes Press the ¢ button to advance the minutes, or press the 4 button to make the minutes go back. 5 Press the MENU button to end the Calendar Adjustment mode. Calendar Mode You can set the date formats of the calendar function. Display and setting: 1 Select the display "Date Mode" during the selecting function in the menu system. 2 Press the 4 and ¢ button to select the date format you want to show in the display. The sample of the date format for today is displayed. 4 Press the MENU button to end the Manual Time Adjustment mode. Exiting the Manual Time Adjustment mode would start the clock counting. — 40 — 1 Select the display "Icon/Speana Select" during the selecting Automatic Time Adjustment function in the menu system. With automatic time adjustment, you can set the clock time automatically according to time data sent from RDS stations (after receiving RDS signals for several minutes). You can also set the time manually if the automatic time adjustment function is turned off. 2 Pressing the 4 or ¢ button switches the Icon/Spectrum analyzer. Display and setting: "SYNC ON" : Automatic time adjustment (Default setting) "SYNC OFF" : Manual time adjustment Adjusting Time Automatically: Tune into an RDS station for 3 or 4 minutes. The time adjusts automatically to the correct local time. Font Select You can change the font used on the display. Display and setting: 1 Select the display "Font Select" during the selecting function in the menu system. 2 Pressing the 4 or ¢ button switches the font on the display. NOTE The time is not adjusted when the RDS station you are tuned to is not transmitting a time signal. Choose another RDS station in such a case. Dimmer Disabled System Indicator (DSI) A red indicator blinks on the unit after the faceplate is removed, warning potential thieves. You can dim the display. Display and setting: "DSI ON" : The disabled system indicator is on. (Default setting) "DSI OFF" : The disabled system indicator is off. The dimmer function is not available for units if the dimmer cable is not connected. Display and setting: "Dimmer ON" : The dimmer setting is on. (Default setting) "Dimmer OFF" : The dimmer setting is off. NOTE Icon/Spectrum analyzer Select This function permits switching of the spectrum analyzer display. Display and setting: — 41 — English Menu settings System Q Switching Dual Zone System Output When this system is set to on, the System Q factors (Bass centre frequency, Bass quality factor, Bass extend, Middle centre frequency, Middle quality factor, and Treble centre frequency) appear during the audio control mode. You can select the speaker output, either front or rear, for the TV(AUX) source. Display and setting: "Zone 2 Rear" : Output from the rear speaker (Default setting) "Zone 2 Front" : Output from the front speaker Display and setting: "System Q ON" : The System Q factors appear and can be adjusted. (Default setting) "System Q OFF" : The System Q factors do not appear. NOTE Not available during the Dual zone system is on. External Amp Control Switching preout Switch the preout between the rear and non-fading. When you switch to non-fading, you can adjust the volume separately. Adjust the bass boost level of the external amplifier using the main unit. Display and setting: "SWPRE Rear" : Rear preout (Default setting) "SWPRE N-Fad" : Non-fading preout Display and setting: "AMP Bass Flat" : Bass boost level is flat. (Default setting) "AMP Bass +6" : Bass boost level is low (+6dB). "AMP Bass +12" : Bass boost level is high (+12dB). NOTE You cannot use the high-pass filter with non-fading preout. NOTE As of December 2000, the power amplifiers controllable by the main unit are as follows: KAC-X501F/PS501F/X401M/PS401M/X301T/PS301T/X201T/PS201T Built-in Amp Mute Control Toggles on or off the mute control on the built-in amplifier. Turning on this control enhances the preout quality. Display and setting: "Builtin AMP Mute ON" : Built-in Amp Mute is ON. "Builtin AMP Mute OFF" : Built-in Amp Mute is OFF. (Default setting) News Bulletin Function with PTY News Timeout Setting You can arrange to have news bulletins interrupt your current listening source, including other radio stations. When the News Bulletin function is on, the PTY News Timeout setting allows you to set the interval during which further news interruption cannot take place. You can adjust the PTY news interruption period from 10 to 90 minutes for each journey. — 42 — Display and setting: "News OFF" (Default setting), "News 00min" – "News 90min" (min= minutes) : When you select the news interruption timeout interval, the News function turns on and the NEWS indicator lights up. When a news bulletin is received, "NEWS" will be displayed and reception will begin at the preset volume. NOTE • If you choose the "20min" setting, further news bulletins will not be received for 20 minutes once the first news bulletin is received. • This function is only available if the desired station sends PTYcode for news bulletin or belongs to -Network sending PTY-code for news bulletin. • If you turn on the news bulletin function in the MW/LW band, the band is switched automatically to the FM band. However, the MW/LW band is not returned to when you turn off the function. Local Seek Function With the local seek function turned on, auto seek tuning skips stations with relatively poor reception. Display and setting: "Local.S ON" : The local seek function is on. "Local.S OFF" : The local seek function is off. (Default setting) Selecting Tuning Mode Auto Memory Entry You can automatically store all the receivable frequencies in the band currently being listened to, and then recall them with the touch of a button later. This function is especially useful when you are travelling and do not know what stations are available. Up to 6 frequencies can be stored this way. Display and setting: 1 Select the display "Auto-Memory" during the selecting function in the menu system. 2 Hold down either the 4 or ¢ button for two seconds or more to start auto memory function. The numbers of the preset station buttons showed in order. When all the stations in a certain band are stored in the preset memory, the auto memory entry stops. The tuner then plays the last station received. NOTE • When the AF function is turned on whilst auto memory entry takes place, only RDS stations (i.e., stations with RDS capability) are stored. RDS stations that have been preset for FM1 cannot also be preset in FM2 or FM3. • When the local seek function is turned whilst auto memory entry takes place, stations with poor reception are not stored. • When the Traffic Information function is on, only the local traffic information station frequency will be stored. Cancelling Auto Memory Entry During Its Operation: Press the 4 / ¢ button whilst auto memory entry is taking place to stop the process. Recalling a Preset Station: Press the preset station button (#1-6) for the desired station. The number of the recalled station is displayed. You can choose from three tuning modes: auto seek, preset station seek, and manual. Display and setting: "Seek Mode Auto1" : Auto seek tuning mode (Default setting) "Seek Mode Auto2" : Preset station seek tuning mode "Seek Mode Manual" : Manual tuning mode — 43 — English Menu settings AF (Alternative Frequency) Function Auto TP Seek Function When poor reception is experienced, automatically switch to another frequency broadcasting the same programme in the same RDS network with better reception. The RDS indicator lights up when the AF function is turned on. Display and setting: "AF ON" : The AF function is on. (Default setting) "AF OFF" : The AF function is off. NOTE When no other stations with stronger reception are available for the same programme in the RDS network, you may hear the incoming broadcast in bits and snatches. Turn off the AF function in such a case. Restricting RDS Region (Region Restrict Function) You can choose whether or not to restrict the RDS channels, received with the AF function for a particular network, to a specific region. When the Region Restrict Function is on, the region is restricted. Display and setting: "Regional ON" : The Region Restrict Function is on. (Default setting) "Regional OFF" : The Region Restrict Function is off. When the TI function is on and poor reception conditions are experienced when listening to a traffic information station, another traffic information station with better reception will be searched for automatically. This function is on, when unit is first powered on. Display and setting: "ATPS ON" : The Auto TP Seek Function is on. If the traffic information station you are tuned to experiences poor reception, this function automatically seeks another TP station. (Default setting) "ATPS OFF" : The Auto TP Seek Function is off. Monaural Reception When poor stereo reception is experienced, this function will reduce noise and improve listening conditions. Display and setting: "MONO ON" : The monaural reception is on. "MONO OFF" : The monaural reception is off. (Default setting) NOTE Sometimes stations in the same network broadcast different programmes or use different programme service names. Reading the MP3 ID3 tag ID3 tag information in the MP3 file is configured for use. Display and setting: "ID Read ON" : ID3 tag is read. (Default setting) "ID Read OFF" : ID3 tag is not read. NOTE • If you switch this setting during the play of MP3, the track is replayed from the beginning. — 44 — • If you turn the ID3 tag read ON, beginning of the play is delayed for reading process of each tag for the tune. Text Scroll This function permits the CD text, MD title, folder/file name and ID3 tag(Song title, Artist, Album) to be scrolled and the entire text to be displayed. Switching between manual scrolling and automatic scrolling is permitted. Built-in AUX Control The "Built-in AUX Control" determines whether you include the TV(AUX) factor in the cycle-through items in the "Switching Modes" (page 11) function. Display and setting: "Builtin AUX ON" : The TV(AUX) factor apears. (Default setting) "Builtin AUX OFF" : The TV(AUX) factor does not apear. NOTE Not available during the Dual zone system is on. Display and setting: "Scroll Auto" : Automatic scrolling "Scroll Manual" : Manual scrolling (Default setting) Power OFF Timer Set the time for the OFF Timer function activated when you selected Standby mode. If the predefined time elapses, this unit's power is automatically turned off. Display and setting: "OFF – – – –" : Power OFF Timer function is cancelled. "OFF 20min" : Unit's power goes OFF after 20 minutes. (Default setting) "OFF 40min" : Unit's power goes OFF after 40 minutes. "OFF 60min" : Unit's power goes OFF after 60 minutes. NOTE The Power OFF Timer function is enabled only after the security code (page 39) is set up. — 45 — English Basic Operations of remote control 2CAUTION Do not set the remote control on hot places such as above the dashboard. Loading and Replacing the Batteries: Use one lithium battery (CR2025). Remove the case following the instructions as illustrated. 1 Keep on slide 2 Pull out Insert the batteries with the + and – poles aligned properly, following the illustration inside the case. 2WARNING Store unused batteries out of the reach of children. Contact a doctor immediately if the battery is accidentally swallowed. Basic operations • VOL buttons Press the 5 button to turn the volume up. Press the ∞ button to turn the volume down. • SRC button Each time you press the SRC button, the mode switches as follows: — 46 — Tuner features ▼ Tuner mode ▼ CD/MP3 mode ▼ External disc control mode 1 ▼ External disc control mode 2 / AUX mode ▼ TV(AUX) ▼ Standby mode NOTE • The mode switches to the next mode from any mode which cannot be used. • The external disc control mode will differ depending on the unit that is connected. • You cannot use the AUX input function of the optional switching adapter KCA-S210A if this unit is connected with the KCAS210A. • If you have selected Standby mode, the timer function that turns the power off automatically will be activated. To find out how to set the time on the timer, and how to cancel the timer function, refer to the section on the Power OFF Timer function under Menu settings (page 45). The Power OFF Timer function is enabled only after the security code (page 39) is set up. • ATT button Turns down the volume quickly. To return the volume to its original level, press the button again. Turning the volume up, or turning it all the way down deactivates the attenuator function. • 4/¢ buttons Press the 4 button to make decreasing seeks (using the preset tuning mode). Press the ¢ button to make increasing seeks (using the preset tuning mode). • AM/FM buttons Press the AM button to select the MW and LW bands. Press the FM button to select and switch between FM1, FM2, and FM3 bands. • DIRECT/OK button During Preset station seek with programme service name mode, selects station. Enters and cancells the Direct access tuning mode. • DNPP button Enters and cancells the Preset station seek with programme service name mode. • 38 button Enters and cancells the Programme Type Selection (PTY) mode. • Number/letter entry buttons Press buttons #1-6 to recall preset stations. Use to enter frequency of the desired station during Direct access tuning mode. — 47 — English Basic Operations of remote control CD/MP3/External disc control features • 4/¢ buttons Press the 4 button to search through the tracks and files backward. Press the ¢ button to search through the tracks and files forward. Used to move the cursor whilst entering disc name. • DISC buttons (for disc changers and media containing MP3 files) Press the DISC– button to search through the discs and folders backward. Press the DISC+ button to search through the discs and folders forward. Selects numbers and symbols whilst entering disc name. • 38 button When a disc is playing, this button pauses the play. Press the same button again to start play again. Selects the type of characters at the time of entering the disc name. • OK button During disc name input, stores the already input data in memory and ends the input mode. Selects disc during the disc name preset play mode. • DNPP button (for disc changers) Enters and cancells the Disc Name Preset Play mode. • Number / letter entry buttons Used to specify the track (disc) number used in direct track (disc) searches. Use to enter letters during disc name preset. — 48 — Accessories External view ......... Number of items 1 ..........................1 2 ..........................2 3 ..........................1 4 ..........................1 2CAUTION The use of any accessories except for those provided might result in damage to the unit. Make sure only to use the accessories shipped with the unit, as shown above. Installation Procedure 1. To prevent short circuits, remove the key from the ignition and disconnect the -terminal of the battery. 2. Make the proper input and output cable connections for each unit. 3. Connect the cable on the wiring harness. 4. Take Connector B on the wiring harness and connect it to the speaker connector in your vehicle. 5. Take Connector A on the wiring harness and connect it to the external power connector on your vehicle. 6. 7. 8. 9. Connect the wiring harness connector to the unit. Install the unit in your car. Reconnect the - terminal of the battery. Press the reset button. 2CAUTION • If your car is not prepared for this special connection-system, consult your KENWOOD dealer. • Only use antenna conversion adapters (ISO-JASO) when the antenna cord has an ISO plug. • Make sure that all cable connections are securely made by inserting jacks until they lock completely. • If your vehicle's ignition does not have an ACC position, or if the ignition cable is connected to a power source with constant voltage such as a battery cable, the power will not be linked with the ignition (i.e., it will not turn on and off along with the ignition). If you want to link the unit's power with the ignition, connect the ignition cable to a power source that can be turned on and off with the ignition key. • If the fuse blows, first make sure that the cables have not caused a short circuit, then replace the old fuse with one with the same rating. • Do not let unconnected cables or terminals touch metal on the car or anything else conducting electricity. To prevent short circuits, also do not remove the caps on the ends of the unconnected cables or the terminals. • Connect the speaker cables correctly to the terminals to which they correspond. The unit may receive damage or fail to work if you share the - cables and/or ground them to any metal part in the car. • After the unit is installed, check whether the brake lamps, indicators, wipers, etc. on the car are working properly. • Insulate unconnected cables with vinyl tape or other similar material. • Some disc changers need conversion cables for connection. See the section on "Safety Precautions" for details. • If the console has a lid, make sure to install the unit so that the faceplate does not hit the lid when closing and opening. • Mount the unit so that the mounting angle is 30° or less. — 49 — Connecting Cables to Terminals Pin Numbers for Cable Colour ISO Connectors Functions Front right output (Red) Yellow Blue/White Orange/White Red Black Battery Power Control Dimmer Ignition (ACC) Earth (Ground) Connection Front left output (White) AUX right input (Red) AUX IN Speaker Connector B–1 B–2 B–3 B–4 B–5 B–6 B–7 B–8 Rear left output/ Non-fading left output (White) FRONT External Power Connector A–4 A–5 A–6 A–7 A–8 REAR NON FADING English Rear right output/ Non-fading right output (Red) Connector Function Guide AUX left input (White) Antenna Conversion Adaptor (ISO–JASO) (Accessory3) Fuse(10A) Purple Purple/Black Gray Gray/Black White White/Black Green Green/Black Rear Right (+) Rear Right (–) Front Right (+) Front Right (–) Front Left (+) Front Left (–) Rear Left (+) Rear Left (–) FM/AM antenna input Antenna Cord (ISO) To KENWOOD disc changer/ DAB control input KPA-SD100/KPA-HD100/KPA-SS100 Wiring harness (Accessory1) NOTE To connect these leads, refer to the relevant instruction manuals. External amplifier control cable (Pink / Black) EXT. CONT. Battery cable (Yellow) TEL mute cable (Brown) Ignition cable (Red) TEL MUTE To "EXT.AMP.CONT." terminal of the amplifier having the external amp control function. Connect to the terminal that is grounded when either the telephone rings or during conversation. NOTE A–7 Pin (Red) Power control/ Motor antenna control cable (Blue/White) P.CONT A–4 Pin (Yellow) ANT. CONT. Connector A 8 7 6 5 4 3 2 1 Connector B 8 7 6 5 4 3 2 1 — 50 — NOTE If no connections are made, do not let the cable come out from the tab. To connect the KENWOOD navigation system, consult your navigation manual. Connect either to the power control terminal when using the optional power amplifier, or to the antenna control terminal in the vehicle. Installation 2WARNING Connecting the ISO Connector (see p.50) The pin arrangement for the ISO connectors depends on the type of vehicle you drive. Make sure to make the proper connections to prevent damage to the unit. The default connection for the wiring harness is described in 1 below. If the ISO connector pins are set as described in 2 or 3, make the connection as illustrated. ■ Installation Firewall or metal support Screw (M4X8) (commercially available) 1 (Default setting) The A-7 pin (red) of the vehicle's ISO connector is linked with the ignition, and the A-4 pin (yellow) is connected to the constant power supply. Unit Vehicle Ignition cable (Red) A–7 Pin (Red) Battery cable (Yellow) A–4 Pin (Yellow) 2 The A-7 pin (red) of the vehicle's ISO connector is connected to the constant power supply, and the A-4 pin (yellow) is linked to the ignition. Unit Vehicle Ignition cable (Red) A–7 Pin (Red) Battery cable (Yellow) Metal mounting strap (commercially available) NOTE Make sure that the unit is installed securely in place. If the unit is unstable, it may malfunction (eg, the sound may skip). A–4 Pin (Yellow) 3 The A-7 pin (red) of the vehicle's ISO connector is not connected to anything, whilst the A-4 pin (yellow) is connected to the constant power supply (or both the A-7 (red) and A-4 (yellow) pins are connected to the constant power supply). Unit Vehicle Connect to a power source that can be Ignition cable (Red) turned on and off with the ignition key. Battery cable (Yellow) Self-tapping screw (commercially available) Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and attach it in place. A–4 Pin (Yellow) 2CAUTION To attach this unit, make sure the front of the control panel faces you and fit it into the mounting sleeve by pressing the four corners of the hard rubber frame at the same time. Do not apply strong pressure to other sections than the corners; otherwise troubles such as the impossibility of opening or closing the panel may result. — 51 — English Installation ■ Removing the hard rubber frame ■ Removing the Unit 1 Engage the catch pins on the removal tool and remove the 1 Refer to the section “Removing the hard rubber frame” and two locks on the lower level. Lower the frame and pull it forward as shown in the figure. Lock then remove the hard rubber frame. 2 Remove the screw (M4´8) on the back panel. 3 Insert the two removal tools deeply into the slots on each side, as shown. Catch Screw (M4X8) (commercially available) Accessory2 Removal tool Accessory2 Removal tool 2 When the lower level is removed, remove the upper two locations. 4 Lower the removal tool toward the bottom, and pull out the unit halfway whilst pressing towards the inside. 2CAUTION Be careful to avoid injury from the catch pins on the removal tool. 5 Pull the unit all the way out with your hands, being careful not to drop it. NOTE The frame can be removed from the top side in the same manner. — 52 — ■ Screwing the Faceplate on the Unit If you want to fasten the faceplate to the main unit so that it does not fall off, screw in the provided screw (M2 ´ 3 mm) in the hole shown below. Accessory4 2CAUTION Never insert the provided screw (M2 ´ 3 mm) in any other screw hole than the one specified. If you screw it in another hole, it will contact and may cause damage to the mechanical parts inside the unit. — 53 — English Troubleshooting Guide What might appear to be a malfunction in your unit may just be the result of slight misoperation or miswiring. Before calling service, first check the following table for possible problems. PROBLEM The power does not turn on. POSSIBLE CAUSE SOLUTION The fuse has blown. After checking for short circuits in the cables, replace the fuse with one having the same rating. No ACC position on vehicle ignition. Connect the same cable to the ignition as the battery cable. If you have selected Standby mode, the power will go OFF automatically. The Power Off Timer function has been activated. If you do not want the power to go OFF automatically, cancel the Power Off Timer function. Nothing happens when the buttons are pressed. The computer chip in the unit is not functioning normally. Press the reset button on the unit (see page 4). Radio reception is poor. The car antenna is not extended. Pull out the antenna all the way. The antenna control cable is not connected. Connect the cable correctly, referring to the section on "Connecting Cables to Terminals". The battery cable has not been connected to the proper terminal. Connect the cable correctly, referring to the section on "Connecting Cables to Terminals". The ignition and battery cable are incorrectly connected. Connect the cable correctly, referring to the section on "Connecting Cables to Terminals". The TEL mute function does not work. The TEL mute cable is not connected properly. Connect the cable correctly, referring to the section on "Connecting Cables to Terminals". The TEL mute function turns on even though the TEL mute cable is not connected. The TEL mute cable is touching a metal part of the car. Pull the TEL mute cable away from the metal part of the car. Free switching of the sound quality. The system Q function is set on Scan mode. Refer to the “System Q” page and switch it to a function other than Scan mode. (see p. 16). Audio control setting cannot be achieved. The system Q function is set on Scan mode. Refer to the “System Q” page and switch it to a function other than Scan mode.(see p. 16). TV (AUX) cannot be selected. "Built-in AUX Control" is turned off. Refer to the "Built-in AUX Control" in the menu setting (page 45) and turn on the "Built-in AUX Control" . The memory is erased when the ignition is turned off. — 54 — PROBLEM No sound can be heard, or the volume is low. POSSIBLE CAUSE SOLUTION The Attenuator function is turned on. Turn off the Attenuator function. The fader and/or balance settings are set all the way to one side. Reset the fader and/or balance settings. The input/output cables or wiring harness are connected incorrectly. Reconnect the input/output cables and/or the wiring harness correctly. See the section on "Connecting Cables to Terminals". "Built-in Amp Mute Control" is turned on. Refer to the "Built-in Amp Mute Control" in the menu setting (page 42) and turn off the "Built-in Amp Mute Control" . A speaker cable may be pinched by a screw in the car. Check the speaker wiring. The speakers are not wired correctly. Reconnect the speaker cables so that each output terminal is connected to a different speaker. The CD is upside-down. Load the CD with the labelled side up. The CD is quite dirty. Clean the CD, referring to the section on "Cleaning CDs" (see page 6). The sound skips on a CD. The CD is scratched or dirty. Clean the CD, referring to the section on "Cleaning CDs" (see page 6). The specified track does not play. Random play has been selected. Turn off the random play function. Can’t remove disc. The cause is that more than 10 minutes has elapsed since the vehicle ACC switch was turned OFF. The disc can only be removed within 10 minutes of the ACC switch being turned OFF. If more than 10 minutes has elapsed, turn the ACC switch ON again and press the Eject button. The sound quality is poor or distorted. A CD ejects as soon as it is loaded. — 55 — Troubleshooting Guide English CD/MP3/External disc control mode PROBLEM POSSIBLE CAUSE SOLUTION The disc control mode cannot be selected. No cable has been connected to the disc changer input terminal on the unit. Connect the cable to the disc changer input terminal on the unit. The specified disc does not play, but another one plays instead. The specified CD is very dirty. Clean the CD. The CD is upside-down. Load the CD with the labelled side up. The disc is loaded in a different slot from that specified. Eject the disc magazine and check the number for the specified disc. The disc is severely scratched. Try another disc instead. Something is touching the disc changer. Remove whatever is touching it. The CD is scratched or dirty. If skipping happens at the same place when the car is stopped, something is wrong with the CD. Clean the CD. The display shows that the changer is being played, but no sound can be heard. The computer chip in the unit is not functioning normally. Press the reset button on the unit (see page 4). The specified track does not play. Random play or magazine random play has been selected. Turn off the random play or magazine random play function. Track repeat, disc repeat, track scan, random play, and magazine random play start by themselves. The setting is not cancelled. The settings for these functions remain on until the setting to off or the disc ejected, even if the power is turned off or the source changed. Cannot play CD-R or CD-RW. Finalization processing is not being conducted for CDR/CD-RW. Conduct finalization processing with CD recorder. A non-compatible CD changer is being used to play the CD-R/CD-RW. Use a CD changer compatible with CD-R/CD-RW to play. The sound skips. If the following situations, consult your nearest service centre: • Even though the disc changer is connected, the Disc Changer Mode is not on, with "AUX" showing in the display during the Changer Mode. • Even though no device (CA-C1AX, KDC-CPS87, KDC-CX87, KDC-CPS85, KDC-CX85, KDC-CPS82 or KDC-CX82) is connected, the AUX Mode is entered when switching modes. — 56 — PROBLEM Cannot play an MP3 file. POSSIBLE CAUSE SOLUTION Not conforming to ISO 9660 Level 1/2. Use a medium conforming to ISO 9660 Level 1/2. The MP3 file has no or invalid file name extension. Add the ".MP3" extension to the MP3 file name. The media is scratched or dirty. Clean the media, referring to the section on "Cleaning CDs" (see p.6). Noise or no sound generated when an MP3 file is played. The file has the MP3 file name extension while it is not an MP3 file. Do not use the ".MP3" extension in non-MP3 files. Takes time before the unit starts playing MP3 files. The medium contains many folders, files, and hierarchical levels. The unit checks all files on the loaded medium first. If the medium has many files recorded, it may take a long time for the unit before it starts playing MP3 files. Fails to play MP3 files in the intended order. The MP3 files were not written by the CD writer in the order in which you wanted them to be played. Depending on the CD writer, you may be able to set the order in which MP3 files are to be played by writing them onto a medium with their file names beginning with play sequence numbers such as "01" to "99". The sound skips when an MP3 file is being played. The media is scratched or dirty. Clean the media, referring to the section on "Cleaning CDs" (see p.6). — 57 — English Troubleshooting Guide The following messages are displayed when certain problems are occurring in your system. Take the recommended actions. Eject No disc magazine has been loaded in the changer. The disc magazine is not completely loaded. ] Load the disc magazine properly. No CD in the unit. ] Insert the CD. No Disc No disc has been loaded in the disc magazine. ] Load a disc into the disc magazine. TOC Error No disc has been loaded in the disc magazine. ] Load a disc into the disc magazine. The CD is very dirty. The CD is upside-down. The CD is scratched a lot. ] Clean the CD and load it correctly. Blank Disc Nothing has been recorded on the MD. No Tr Disc No tracks are recorded on the MD, although it has a title. NO PANEL The faceplate of the slave unit being connected to this unit has been removed. ] Replace it. E-77 The unit is malfunctioning for some reason. ] Press the reset button on the unit. If the "E- 77", code does not disappear, consult your nearest service centre. Mecha Error Something is wrong with the disc magazine. Or the unit is malfunctioning for some reason. ] Check the disc magazine. And then, press the reset button on the unit. If the "Mecha Error" code does not disappear, consult your nearest service center. Hold Error The protective circuit in the unit activates when the temperature inside the automatic disc changer exceeds 60°C (140°F), stopping all operation. ] Cool down the unit by opening the windows or turning on the air conditioner. As the temperature falls below 60°C (140°F), the disc starts playing again. IN If this indicator blinks, the CD player is malfunctioning. ] Eject the CD and try inseting it again. If the CD cannot be ejected, press the eject button and hold it in until the CD is ejected. — 58 — Specifications Specifications subject to change without notice. FM tuner section Audio section Frequency range (50 kHz space) ...............87.5 MHz – 108.0 MHz Usable sensitivity (S/N = 26dB) .................................0.7 µV/75 ½ Quieting Sensitivity (S/N = 46dB) ..............................1.6 µV/75 ½ Frequency response (±3.0 dB) ..............................30 Hz – 15 kHz Signal to Noise ratio (MONO) ..............................................65 dB Selectivity (DIN) (±400 kHz) .............................................³ 80 dB Stereo separation (1 kHz) ....................................................35 dB MW tuner section Frequency range (9 kHz space) ......................531 kHz – 1611 kHz Usable sensitivity (S/N = 20dB) ...........................................25 µV LW tuner section Frequency range..............................................153 kHz – 281 kHz Usable sensitivity (S/N = 20dB) ...........................................45 µV Maximum output power .................................................47 W ´ 4 Full Bandwidth Power (DIN 45324, +B=14.4V) ...............22 W ´ 4 Tone action Bass :...........................................................100 Hz ±10 dB Middle :..........................................................1 kHz ±10 dB Treble : .........................................................10 kHz ±10 dB Preout level / Load (during disc play) ....................1800 mV/10 k½ Preout impedance .............................................................²600 ½ General Operating voltage (11 – 16V allowable)................................14.4 V Current consumption .............................................................10 A Installation Size (W x H x D) ..........................182 ´ 53 ´ 156 mm Weight.................................................................................1.8 kg CD player section Laser diode ....................................................GaAlAs (l=780 nm) Digital filter (D/A)......................................8 Times Over Sampling D/A Converter ...............................................................8 level DS Spindle speed (CD-DA) .................................500 – 200 rpm (CLV) (MP3) ..................................1000 – 400 rpm (CLV) Wow & Flutter ........................................Below Measurable Limit Frequency response (±1 dB) .................................10 Hz – 20 kHz Total harmonic distortion (1 kHz) ......................................0.01 % Signal to Noise ratio (1 kHz) ................................................96 dB Dynamic range ....................................................................95 dB Channel separation..............................................................90 dB MP3 decode ...................Compliant with MPEG-1.0 Audio Layer-3 — 59 —
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : No Page Count : 60 Create Date : 2001:08:21 01:45:11 Producer : Acrobat Distiller 3.02 pour Power Macintosh Author : G4 Creator : QuarkXPress Passportª 4.1.1 [k]: PSPrinter 8.3.1 Title : Z828 (EN)EXIF Metadata provided by EXIF.tools