Keter KT-1000F Dual Mode Digital Camera User Manual

Download:
Mirror Download [FCC.gov]
Document ID	166698
Application ID	jijUlziyieQXbS3lnU5K9Q==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	46.06kB (575767 bits)
Date Submitted	2001-08-28 00:00:00
Date Available	2001-08-28 00:00:00
Creation Date	2001-07-21 12:03:46
Producing Software	Adobe PDF Library 2.0
Document Lastmod	2001-08-22 15:16:12
Document Title	Users Manual

Copyright® 2&1 Keter Corporation All rights reserved.
Keter Corporation asaimes no responsibility for errors or omissions
in this manual and information in the manual is subject to change
without notice.
No part of this manual can be reproduced or transmitted in any
form or by any means without prepermission of Keter Corporation.
Photo Impresion TM 3.0 is provided by ArcSoftJnc. All rights
reserved.
First edition D ate : A ug ust 2, 2131
/—\
FCC STATEMENT
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and
us ed in accordance with the instructions, may cause
harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception, which
can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by
one or more of the following measure:
— Reorient or relocated the receiving antenna.
- Increase the separation between the equipment and
receiver.
- Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
- Consult the dealer or an experienced radio/ TV technician
for help.
- Shielded cables must be used to comply with FCC
regulations.
WARNING (PART 15, SECTION 15.21)
Changes or modifications not expressly approved by the
party responsible for compliance could void the user's
authority to operate the equipment.
\ m
/ \
CONTENTS
Introducing "Eye—on" Digital camera ~~~~~~~ 06
Top and Front ---------------- 07
LCD Display; camera Dis play Panel ------- 08
How to use ;PreparingStill Camera - - - - - - - O9
Attacingthe necklacestrap ~ - - ~ - . . . . . . 10
Turningthecameraonandoff - ~ ~ ~ - - - ~ - 11
Focusing Eyeon ............... 12
Cam era mod es ---------------- 13
Taking snapshot --------------- 15
Using the timer ---------------- 16
Using mu] ti-snap Mode ............ 17
Capturing video clips (Live video and audio) ~ - - 18
Audio (Voice) recording ------------ 19
Audio playback ----- - - - - - ~ - - ~ - 20
How much memory is lett ----------- 21
File deleting ................. 22
format - - ~ ~ ------------ ~ ~ ~ 23
Sign for warning ............... 23
How to us ; PreparingPC Camera -------- 25
Trouble Shooting Guide ------------
\ m
x/Efl /
INTRODUCING "EYE—ON" DIGITAL CAMERA
Firstly we, thank you for your purchasing our product
and also congratulate you on entering multimedia world
with our high—tech dual mode digital camera, EYE -ON.
Unlikely other camera, you can take not only snapshotbut
also live video including live voice all together ,with you
PC or without your PC.
} THE MAIN FEATURES OF EYE—ON ARE AS
FOLLOWS.
- High quality and clear picture (640 X480 pixels)
- Multi—functions
1. Still Camera
1) Still image (Max 218cuts)
- Multi snap shot (3 cuts per one shot)
- Self timer(10 sec)
2) Video clip (Max 108secs)
~ Live video and audio just like video camera
2. PC (Web) Camera (U SB connection with PC)
~ Video conferencing] Video email
3. Voice recording (30 minutes)
4. Powerful Sf W5
1) ArcSoft Photo impression 3.0
2) ArcSoft Photo Base 2.1
Please review this manual carefully to enjoy all
powerful functions of Eye-on before you run the
product,and keep this manual besides you for any
possible troubles you may experiences.
/ \
TOP AND FRONT
Snapshot button
Strap hole
View finder
Fouls ring
Lets
USB mnnector
Cama'astand
View finde'
Microphone
Mode button
Delde button
LCD Panel
Pow er button
Speaker
Fixation groove for
mum stand
Battey wver
\ m
L/ofi /
LCD DISPLAY; CAMERA DISPLAY PANEL
©0®©®®
®® ®®©®
® Number or time for files
(2) Icon for snapshot mode
C3) Icon for video clip (motion picture, live Video) mode
@ Icon for VGA high (high quality image),
non-compression mode
6) Icon for VGA low (normal quality image), ]'PEG like
compression mode
© Icon for battery
® Icon for VGA
Recording
© Icon for microphone
® Icon for speaker
® Icon for formatmode
® Icon for timer mode
/ \
HOW TO USE; PREPARING STILL CAMERA
YourEye—on can be used in two different ways, one is for
still camera and the other is for PC (Web) camera.
Followings are for still camera operation and please refer to
seperated manual for PC camera operation.
) STILL CAMEAR ,' INSTALLING THE BATTERIES
1. Open the battery compartment
by pushing and sliding down
the cover as shown.
2. Insert the 2 pcs of"AAA"
batteries as the direction shown
in the battery compartment
and close the cover.
Once the battery is used up,
replace it in the same way.
If your Eye—on is flashmemory
version (KTlCDOF) then the
images in the camera are kept
safe even though the battery is used up. If your Eye-on is
SDRAM version (KTlOCDS), you need to replace battery
within one minutes after you have warning sign from Eye
on. ("Full' is displayed and blinking in the LCD. Please refer
to "sign for warning" in the later part of this manual for
more details)
x REMARK
1. Make sure that batteries are inserted in the right
direction. Otherwise the camera will not work.
2. Batteries are needed only when Eye-on is used as Still
camera. 80 you would better remove the batteries from
the Eye-on when you use it as a PC camera for a long
time.
\ m
/ \ f \
ATTACING THE NECKLACE STRAP TURNING THE CAMERA ON AND OFF
For your convenience, a necklace strap is supplied with Press the power button for a second and wait 1 or 2
your Eye-on. seconds more for powering on. And then you can see the
It consists of two pieces, a short strap to the camera hole Initial mode screen in the LCD.
and a long one for necklace.
1. Slip the one end ofthe short strap through the camera's
strap hole as shown.
2. Slide the rest of the strap through the small loop as
shown and pull it all the way through to tighten.
3. Connect the short strap and long one using the
connector as shown.
For powering off, press power button again for a second.
And then "OPP" is shown on the LCD for a second and it
will be off.
OFF--
x REMARK
Eye—on is offering you automatic power— off function to
save battary , that is to power off automatically if there
is no button inputmore than 5 minutes.
In the still camera mode, your Eyebn is powered only
from battery so you would better to power it off when
you do not use it for a long time.
/ \
Focuswc EYE-ON
Unlikely in the PG camera mode, you can not know the
status of the focus by your eye.
So in the still camera mode, you need to adjust the focus
approximately according to the distance to the object you
want to take. Adjust the focus ring according to the
following instruction.
Icon for distance
x“ The distance to the object is more than 2meters.
D The distance to the object is around lmeter.
s The distance to the object is less than 20
centimeters.
x REMARK
In the PG camera mode, you can see the status offocus
by image shown through SKYGARDEN and you can
fix the focus accordingly.
xm /
/ \
CAMERA MODES
As you press the mode button, Eye-on circles through
several different modes like High quality snapshot (VGA
high), Normal quality snapshot( VGA low), Timer, Multi
-snap, Audio recoding, Audio playback, Format. Details
are as follows.
uncompressed and 640x 480 pixel images
""""""""""""""""""" \ With the VGA high mode, you can take
0 13mg],
.. , (High quality image) upto 26 cuts.
640x 480 pixel images upto 218 cuts with
u , ]'PEG like compression.
(Normal quality image)
'''''''''''''' \ With the VGA low mode, ou can take
(teams. y
With video clip mode, you can take
320 X 240 pixel motion pictures together
j with the voice upto 168 seconds.
With the timer mode, your Eye-on waits
; for 10 seconds after you press the
u, j snapshot button before taking a VGA
high image.
a; REMARK
This is only available with VGA high mode.
\ m
With the multi—snap mode, you can take
three VGA low image consecutively
(with 0.3 sec interval) whenever you press
snapshot button
is REMARK
This is only available with VGA low mode.
in) . With audio recording mode, you can
record your voice or any other audio
through built-in mike upto 34minutes.
1 With audio playback (backward) mode,
9 you can playback the audio which is
l 4 j recorded in the Eye on. The order of
playback is from the lastly recorded
audio data.
With audio playback (forward) mode, you
can playback the audio which is recorded
j in the Eye on. The order of playback is
from the firstly recorded audio data.
3i fl“ With format mode, you can delete all the
l image and audio data in the camera or
i W initialize wrong file system.
TAKING SNAPSHOT
As described before, your Eye-on offer two different
snapshot mode, VGA high and VGA low. In these modes,
you can take snapshots using snapshot button and view
finder just as a normal camera.
1. Fix the snapshotmode, VGA high or VGA low.
2. Make sure that focus ring is set as the instruction. (Refer
to "Focusing Eyeon")
Otherwise, the picture quality may be very poor
unlikely your expectation.
3. Make sure that the object is located within the View
finder range.
4. Press the snapshot button when you ready then the
image will be taken with a click. Make sure that you
need to hold the camera still for a one or two seconds
for the best result.
5. Whenever the image is taken, the number shown in the
LCD will be added by one, and the number shows the
total number of snapshots taken by that time.
USING THE TIMER
In the timer mode, you can take a picture 10 seconds after
you press the snapshotbuttonbefore taking a VGA high
image.
1. Set the mode to timer.
(This is only available with VGA high mode)
2. Make sure that focus ring is set as the instruction.
(Refer to ”Focusing Eye-on”) Otherwise, the picture
quality may be very poor unlikely your expectation.
3. Make sure that the object is located within the View
finder range and hold the camera with the stand.
4. Once you press the snapshot button, the countdown
will be shown on the LCD from 9 and it take the picture
with the click after 10 senconds.
5. When the image is taken, the number shown in the LCD
will be added by one, and the number shows the total
number of snapshots with the VGA high mode by that
time.
In this mode, you can take three VGA low image
consecutively (with 0.3 sec interval) whenever you press
snapshot button.
1. Set the mode to timer.
(This is only available with VGA low mode)
And make sure that focus ring is set as the instruction.
(Refer to ‘Pocusing Eye-on”).
Otherwise, the picture quality may be very poor
unlikely your expectation.
2. Make sure that the object is located within the
viewfinder range and hold the camera still for one or
two seconds for the best result.
3. Once the snapshot button is pressed, it will take three
pictures consecutively with a click.
4. When the pictures are taken, the number shown in the
LCD will be added by three and the number shows the
total number of snapshots with VGA low mode by that
time.
he REMARK
Any button pressed when multi-snap is being taken is
not effective.
USING MULTI-SNAP MODE
CAPTURING VIDEO CLIPS (LIVE VIDEO AND AUDIO)
In video clipmode, you can take 320 X 240 pixel motion
pictures (live video) together with the audio during you
press the snapshot button and it is available upto 108
seconds.
The time elapsed for recoding is shown in the LCD.
1. Set themode to video clip.
2. Make sure that focus ring is set as the instruction.
(Refer to ”Focusing Eye-on')
Otherwise, the picture quality may be very poor
unlikely your expectation.
3. Make sure that the object is located within the View
finder range.
Press and hold the snapshotbutton until the recording
is finished.
4. When the recordingis finished, 1 et the snaps hot button go.
5. Whenever the video clip is recorded , the number
shown in the LCD will be added by one and the
number shows the total number of video clip by that
time.
AUDIO (VOICE) RECORDING
In the audio recording mode, you can record your voice or
any other audio throughbuilt-in mike upto 34 minutes.
Once you press the snapshot button, the record start and
you can stop it with another pressing the snapshot button.
The time elapsed for recoding is shown in the DOD.
Mint-phone
1. Set the mode to audio recording.
2. Press snapshot button for recording start, and the time
elapsed for recoding is shown in the LCD.
3. Press snapshot button again for stop recording.
4. Whenever the audio file is recorded , the number shown
in the DOD will be added by one and the number shows
the total number of audio files by that time.
as REMARK
The time elapsed for recoding is displayed with second
until 999 seconds, and after that It is displayed with
minutes.
/ \
AUDIO PLAYBACK
As described before, your Eyaon offers two different
audio playback modes, audio playback (backward) mode,
and audio playback (forward) mode.
The only difference is the order of data playback, from the
lastly recorded audio data or from the firstly recorded
data.
1. Set themode to audio playback (backward) or audio
playback (forward).
2. Select the file number which you want to playback and
then press snapshot button.
And press mode button to stop playback. If you press
the snapshotbutton during playback, the next audio file
starts to playback automatically.
3. Once the paly back is finished for a audio file, the
number ofthe next audio file is displayed in the LCD.
You can playback other audio file in the same manner.
in REMARK
If the Eye on is too close to the audio source during the
record, the audio quality in the playback maybe poor.
x/zh /
/ \
HOW MUCH MEMORY IS LEFT
In the allmodes of Eye -on except formatmode, you can
check how much memory is left in each mod e.
The numbers displayed in snapshot and multi snap
modes mean the number of cuts which can be taken more.
And in the audio recording and video clip and audio
playback modes, the number means the time left.
1. Press the mode button in each mode for about a second,
it display the number for cuts or time left in that mode.
2. Let the mode button go after you check the memory left.
if REMARK
1. In the Video clip mode, the time left is displayed with
second.
2. In the audio recoding mode, the time left is displayed
with second ifit is less than 999 seconds, and if it is
more than 999 seconds, it is displayed Withminutes.
3. The number displayed in the LCD as amemory left
can be different from the actual according to the
conditions ofthe picture taking or video, audio
recoding later.
/ \
FILE DELETING
In the all modes of Eye —on except
foymat and playback mode, you
can erase files in each mode
using delete button in two ways
"one by one" or "all".
} DELETING "ONE BY ONE" IS TO DELETE FROM
THE LASTLY RECORDED FILE IN EACH MODE.
1. Press delete button in each mode then the lastly
recorded data will be deleted.
2. Whenever the file is deleted, the number shown in the
LCD will be decreased by one.
} DELETING 'ALL" IS TO DELETE ALL FILES IN
EACH MODE.
1. Press the delete button in each mode for more than 3
seconds, the number in the LCD is blinking and all
files in thatmode will be deleted.
2. When the all files in that mode are deleted, the
number shown in the LCD will be zero.
if REMARK
1. If you press delete button in the formatmode, all the
files in the Eye-on will be deleted.
2. You can delete audio file in both mode of audio
recording and audio playback. In case of audio file
deletion in audio recording mode, just follow above
procedures. In case of audio file deletion in audio
playback(forword or reward) mode, make sure that
file can be deleted only after it is played back, and all
file deletion is not available.
x/z—fl /
/ \
With formatmode, you can delete all the image and audio
files in the camera or initialize wrong file system.
1. Set the mode to format
2. Press deletebutton until the letter of 'DEL" is
disappeared from the LCD.
3. Once the format is finished, the letter of "End" will be
shown in the LCD.
35143”?
as
SIGN FOR WARNING
When the memory is getting full and the memory left is
not enough, the number in the LCD starts blinking.
However it does notmean thatmemory is completely full
so you can take some more images or audio.
When the memory is completely
F ' . full, your Eye-on stops working
U, ' and the letter of"full‘ will be
displayed and blinking in the LCD.
However if you delete some or all files then the LCD will
be restored and the camera will work again.
Make sure to download any file which you want to keep
to your PC before deletion.
\ m
When the battery is running out, the icon for battery is
varying. When the battery is completely used up, the
battery icon will start to blink and then after a few
seconds, the Power will be automatically off.
Once you replace with new battery, the battery icon will
be restored as full condition.
is REMARK
If your Eye-on is flash memory version (KTIEDOF) then
the images in the camera are kept safe even though the
battery is used up.
If your Eye-on is SDRAM version (KTIKDOS), you need
to replace battery within one minutes atter you have
warning sign from Eye on.
HOWTO USE ; PREPARING PC CAMERA
Once you connect the Eye-on to yourPC using USB cable,
it becomes a video camera that enables you capture video
and images directly to your PC.
And now it is operated by the application 8] W named
"SKYGARDEN" and the batteries are not needed anymore
because it is powered from USB cable.
One more thing is, you can edit the images using the S/ W
of "ARCSOFI‘" which is supplied with camera as free.
LH %Q%l

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Modify Date                     : 2001:08:22 15:16:12+09:00
Producer                        : Adobe PDF Library 2.0
Create Date                     : 2001:07:21 12:03:46
Page Count                      : 12

EXIF Metadata provided by EXIF.tools