Keymat Technology DS40 AXS Series S40 iClass SE PIN-Contactless Reader User Manual Engineering Manual

Download:
Mirror Download [FCC.gov]
Document ID	2641833
Application ID	mMfpgabahpnmW9wSS3TA7g==
Document Description	Engineering Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	12.69kB (158576 bits)
Date Submitted	2015-06-09 00:00:00
Date Available	2015-06-09 00:00:00
Creation Date	2015-05-05 11:30:38
Producing Software	Adobe PDF Library 11.0
Document Lastmod	2015-05-05 11:30:40
Document Title	Engineering Manual
Document Creator	Acrobat PDFMaker 11 for Word
Document Author:	Gareth Richards

Engineering Manual for
AXS Series S40/S40i Keypad
AXS SERIES S40 iCLASS SE® PIN-Contactless Reader: This integrated keypad and contactless reader is rated for
continuous outdoor use in exposed, unsupervised locations. Featuring genuine HID™ iCLASS SE®, Seos®,
contactless technology, this access control keypad offers enhanced security by dual factor authentication. Authorized
access through a secured door or barrier can be gained by entry of a valid PIN and/or presentation of an authorized
13.56 MHz contactless card, token or Seos® device
This manual covers the S40 and S40i, and is available from www.storm-interface.com/downloads. Each individual
product includes a printed datasheet with just the essential information for installation.
Table of Contents
Product Range and Accessories/Options
Supported Credentials
Keypad Installation
Wiegand Formats
Typical Wiring (Kantech KT-300 Controller)
Specifications/Regulatory
Whilst every effort is made to ensure details are correct at time of print, specifications are subject to change without notice.
Storm Interface products include technology protected by international patent and design registration. Storm and Storm Interface are trademarks of
Keymat Technology Ltd. Storm Interface is an ISO9001 registered company.Storm is a trading name of KeymatTechnology Ltd
S40/S40i Engineering Manual
Rev 1 April 2015
Page 1 of 5
www.storm-interface.com
© Copyright Storm Interface. 2015. All rights reserved
Engineering Manual for
AXS Series S40/S40i Keypad
Product Range
Two products are included in the range. The S40, which has a metal keypad, and the S40i, which has an illuminated
white polymer keypad. Both products can be powered via the 5V or 12V supply pins. However, the illumination will
only function when powered from 12V
Options
A privacy shield (p/n 1KFS020) is available as an optional extra
Please see the Storm website at www.storm-interface.com
Supported Credentials
The following credentials are supported (additional controller set-up may be required):
iClass
Seos
MiFare Classic
MiFare Plus
MiFare Ultralight
DESFire 0.6
DESFire EV1
Installation
Connection to the Controller is via a 12-way connector. The connector is removable to ease wiring. Recommended locations and
wiring methods shall be in accordance with the National Electrical Code, ANSI/NFPA 70.
Connections are as follows:
Pin A –
Pin B –
Pin C –
Pin D –
Pin E –
Pin F –
Pin G –
Pin H –
Pin I –
Pin J –
Pin K –
Pin L –
5V power input – 5V at 200mA
Beeper input. Active low, pulled up internally. Beep sounds when this pin is set low
Card data hold. Active low, pulled up internally. Set low to hold card data transmission
Tamper output. Connects to 0V when the tamper switch is closed, and is open circuit on a tamper
0V power and signal return
0V power and signal return
RED LED input. Active low, pulled up internally. Low turns on the RED LED (default is on)
GREEN LED input. Active low, pulled up internally. Low turns on the GREEN LED (takes precedence over RED)
12V power input – 200mA for S40, 250mA for S40i
Weigand D1 output. Open collector, pulled up internally
Wiegand D0 output. Open collector, pulled up internally
Tamper output. Open circuit when the tamper switch is closed. Connects to 0V on tamper
Cable lengths of up to 150m are supported, provided the correct power supply voltage is presented to the S40
Connect the Controller Wiegand inputs to the S40 Wiegand outputs, and the Controller Beep and LED control
outputs to the relevant S40 Beep and LED control inputs
S40/S40i Engineering Manual
Rev 1 April 2015
Page 2 of 5
www.storm-interface.com
© Copyright Storm Interface. 2015. All rights reserved
Engineering Manual for
AXS Series S40/S40i Keypad
Physical installation
- Using the case as a template, mark the position of the four holes (A) on the surface.
(or if fixing to an already installed UK or US back box use the relevant hole pattern)
- Drill fixing holes to suit the supplied fixing screws
- Push the cable through the sealing grommet and secure the case to the mounting surface using the fixing screws
- Make the electrical connections to the connector block (the connector block can be removed to aid wiring)
- Position the rubber seal on the mating edge of the rear case.
- Fix the keypad to the rear case using the security screws
- Use the nylon sealing washers under the screw heads to protect against moisture ingress
- Check the installation to ensure the rubber seal is in place and is compressed evenly around the perimeter of the
case.
Weigand Formats
For PIN
Factory default is Weigand 8 bit burst format (for PIN)
If you need Weigand 4 bit burst format, follow the sequence below.
Press # on power up
LED FLASHES RED/GREEN
Press #725 to enter FORMAT mode
Press 1
or
for FORMAT
for RESET TO DEFAULT
Press 0
or
for 4 BIT FORMAT
for 8 BIT FORMAT
Press 0
to EXIT,
LED STAYS RED
This setting is retained even if power is removed
For Cards
Factory default is 26-bit Wiegand for all presented cards. If alternative Wiegand formats are required please contact
us via the website www.storm-interface.com
S40/S40i Engineering Manual
Rev 1 April 2015
Page 3 of 5
www.storm-interface.com
© Copyright Storm Interface. 2015. All rights reserved
Engineering Manual for
AXS Series S40/S40i Keypad
Typical Wiring
Below is a typical wiring schedule – in this case between the S40 and the Kantech KT-300 Controller
The S40 is shown connected to control Door 2.
Where there is an LED connection, usually the GREEN LED connection is appropriate
Wire name
Wiegand Data 0
Wiegand Data 1
0V
+12V
Buzzer
LED
Wire colour
Green
White
Black
Red
Blue
Brown
KT-300
READ2 Green
READ2 White
READER PWR GND
READER PWR +12V
OUT DOOR 2 BUZ
OUT DOOR 2 LED
S40
Pin K
Pin J
Pin E or Pin F
Pin I
Pin B
Pin H
Specifications
Card Compatibility
iClass®, Mifare® serial number
ISO15693, ISO14443A&B
Card Read Range
2-5cm (depending on card)
Card Security
V1 Security (Elite security by special order only)
Coupling Frequency
13.56 MHz
Power supply
5V +/- 10% or 12V +/- 15% DC 200mA / 250mA (illuminated)
(Illumination only active with a 12V power supply)
Cable distance to host
150m max
Tamper detection
Normally open (N.O.), or normally closed (N.C.) tamper switch
Status Indication
RED/GREEN or BEEP as driven by the attached Controller
Tamper switch
Max 30V DC, 500mA
Operational Temperature
-35°C to +65°C
Weather Resistance
IP65
Vibration & Shock
ETSI 6M3
Impact Resistance
IK09 (10J Rating)
Certifications
CE / FCC / UL294
S40/S40i Engineering Manual
Rev 1 April 2015
FCC ID 2AEEZ-DS40
Page 4 of 5
IC 29008-DS40
www.storm-interface.com
© Copyright Storm Interface. 2015. All rights reserved
Engineering Manual for
AXS Series S40/S40i Keypad
Regulatory Information
This device complies with Part 15 of the FCC Rules and Industry Canada licence exempt RSS standard(s).
Operation is subject to the following two conditions:
1. This device may not cause interference, and
2. This device must accept any interference, including interference that may cause
undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
L'exploitation est autorisée aux deux conditions suivantes :
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible
d'en compromettre le fonctionnement.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's
authority to operate the equipment
S40/S40i Engineering Manual
Rev 1 April 2015
Page 5 of 5
www.storm-interface.com
© Copyright Storm Interface. 2015. All rights reserved

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Author                          : Gareth Richards
Create Date                     : 2015:05:05 11:30:38+01:00
Modify Date                     : 2015:05:05 11:30:40+01:00
Subject                         : 
Language                        : EN-GB
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03
Metadata Date                   : 2015:05:05 11:30:40+01:00
Creator Tool                    : Acrobat PDFMaker 11 for Word
Document ID                     : uuid:daabf115-1d51-4086-920b-4d3cb424c51c
Instance ID                     : uuid:fb452bce-55a7-40e8-8d8e-4376c6dc943b
Format                          : application/pdf
Title                           : 
Description                     : 
Creator                         : Gareth Richards
Producer                        : Adobe PDF Library 11.0
Keywords                        : 
Source Modified                 : D:20150505103003
Company                         : 
Comments                        : 
Page Layout                     : OneColumn
Page Count                      : 5

EXIF Metadata provided by EXIF.tools