Keys Fitness Horizontal Pressing Station Kps 2050 Users Manual
KPS-2050 to the manual 5d74b4a5-a3ec-41d4-acec-146f27a5e8ad
2015-02-02
: Keys-Fitness Keys-Fitness-Horizontal-Pressing-Station-Kps-2050-Users-Manual-434898 keys-fitness-horizontal-pressing-station-kps-2050-users-manual-434898 keys-fitness pdf
Open the PDF directly: View PDF .
Page Count: 48
Download | |
Open PDF In Browser | View PDF |
Owner’s Manual Read all precautions and instructions in this manual before using this equipment. 215-00010 09/04 Table of Contents Important Safety Information 3 Before You Start 4 Assembly 5-40 Weight Ratios 41 Weight Stack Sticker Placement 42 Cable View 43 Top View 44 Exploded View 45 Parts List 46 Warranty Information 47 2 Important Safety Information THANK YOU for making this Power System unit a part of your exercise program. Keys Fitness and our Power System Series assures the very best in value, appearance, durability and biomechanics. This manual will guide you through the assembly process. If at any time you are having trouble with the assembly or use of this product, then please contact us at our Keys Fitness Help-line. We have trained service technicians on site to take care of you, our valued customer. REGISTRATION CARD To avoid unnecessary delays in warranty parts and to insure that a permanent record of your purchase is on file with our company, be sure to send in the warranty registration card or register on-line at www.keysfitness.com within 10 days of purchase. POWER SYSTEM SERIES QUESTIONS? CALL 1 -888- 340- 0482 Mon d ay- F rid ay 8 : 3 0 - 5: 30 Cen t ral Tim e When calling please have the following product information available: • Product Series • Model # • PO # (located on the front of the manual) • Part Number • Part Description 3 Before You Start Prior to assembly, remove components from the box and verify that all the listed parts were supplied. NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled. SAFETY INFORMATION WARNING! Before using this unit or starting any exercise program, consult your physician. This is especially important for persons over the age of 35 and/or persons with pre-existing health problems. Keys Fitness Products LP assumes no responsibility for personal injury or property damage sustained by or through the use of this product. It is the owner’s responsibility to ensure that all users of this unit have read the Owner’s Manual and are familiar with safety information and precautions. SAFETY PRECAUTIONS • This Power System unit should only be used on a level surface and is intended for indoor use only. Keys Fitness recommends an equipment mat be placed under the unit to protect the floor or carpet and for easier cleaning. • Wear comfortable, good-quality walking or running shoes and appropriate clothing. Do not use this unit with bare feet, sandals, socks or stockings! • Always examine your unit before using to ensure all parts are in working order. • Do not leave children unsupervised near or on the unit. • Service to your Power System unit should only be performed by an authorized service representative, unless authorized and/or instructed by a Keys Fitness technician. Failure to follow these instructions will void the warranty. 4 Assembly Box 1 5 Assembly Box 2 6 Assembly Box 3 7 Assembly Box 4 8 Assembly Box 5 9 Assembly Box 6 10 Assembly Box 7 Box 8 Box 9 Box 10 Box 11 Box 12 11 Assembly 12 Assembly 13 Assembly 14 Assembly Step 1 Attach Right Base Frame (4) to Rear Frame (1) using two Nuts (144), four Washers (143), and two Bolts (137). Attach Left Base Frame (8) to Rear Frame (1) using two Nuts (144), four Washers (143), and two Bolts (137). Insert Guide Rods (47) into Rear Frame (1). Next, slide Weight Stack Bumpers (99) onto Guide Rods (47). Attach Rear Upright (3) to Rear Frame (1) using two Nuts (144), four Washers (143), and two Bolts (136). Figure 1 15 Assembly Step 2 Slide the weight plates down the Guide Rods (47) in this order - five 15lb Plates (52), nine 10lb Plates (53), five 5lb Plates (54), and the Top Plate (55). Note: Number of weight plates may vary depending on your specific configuration. Attach Up Frame (2) to all four Guide Rods (47) and secure to Rear Upright (3) using two Nuts (144), four Washers (143), and two Bolts (136). Figure 2 16 Assembly Step 3 Attach Front Upright (19) to Seat Pad Support Receptacle (6) using two Nuts (144), four Washers (143), and two Bolts (136). Attach Seat Pad Support Receptacle (6) to Base Frame assembly using two Nuts (144), four Washers (143), and two Bolts (136). Figure 3 17 Assembly Step 4 Attach Main Upright (7) to Seat Pad Support Receptacle (6) using two Nuts (126), four Washers (125), and two Bolts (131). Attach Right Top Frame (5) to Up Frame assembly using two Nuts (144), four Washers (143), and two Bolts (137). Next, use two Washers (143), two Spring Washers (119), and two Allen Bolts (142) to connect Right Top Frame (5). Figure 4 18 Assembly Step 5 Slide Press Station Base Frame (11) over Press Arm Support (10). Next, attach both pieces to Base Frame using two Nuts (144), four Washers (143), and two Bolts (134). Install Left Top Frame (9) over Press Arm Support (10) and Top Frame assembly. Secure top section using two Nuts (144), four Washers (143), and two Bolts (137). Next, Secure lower section using two Nuts (144), four Washers (143), and two Bolts (136). Secure top of Guide Rods (47) using two Washers (143), two Spring Washers (119), and two Allen Bolts (142). Figure 5 19 Assembly Step 6 Attach Pec Dec Mount (21) onto Seat Pad Support Receptacle (6) using two Nuts (144), four Washers (143), and two Bolts (136). Secure in place with one Washer (129), one Spring Washer (119), and one Bolt (137). Figure 6 20 Assembly Step 7 Attach Right and Left Leg Hold Leg Frames (29 & 30) using two Nuts (144), four Washers (143), and two Bolts (135). Figure 7 21 Assembly Step 8 Slide the Right Pec Dec Arm (22) on to the shaft of the Pec Dec Mount (21). Secure the arm in place using one Big Washer (102), one Washer (143), one Spring Washer (119), and one Allen Bolt (128). Slide Pec Dec Handle Bar (24) onto the top of the Right Pec Dec Arm (22) and secure using one Chrome Washer (101), one Washer (143), one Spring Washer (119), and one Allen Bolt (128). Repeat this step to complete the Left Pec Dec assembly. Figure 8 22 Assembly Step 9 Attach Leg Extension Lever (20) to Seat Pad Support Receptacle (6) and secure using Shaft (86), one Washer (117), one Spring Washer (118), and one Allen Bolt (98). Slide Foam Frame w/ Shaft (26) through the Leg Extension Lever (20) and attach Foam Frame w/o Shaft (25) to the other side. Insert Slip Tension Pin (85) through the hole where the two foam frames meet. Note: You may need to use a rubber mallet to install Slip Tension Pin (85). Figure 9 23 Assembly Step 10 Align Press Arm (35) and Chest Press Cam (12) while inserting Press Station Shaft (38). Slide Pillow Block Bearing (75) onto each side of Press Station Shaft (38) and secure the assembly using two Chrome Washers (101), two Washers (143), two Spring Washers (119), and two Allen Bolts (128). Attach the entire assembly to Press Arm Support (10) using four Nuts (126), eight Washers (125), and four Bolts (130). Figure 10 24 Assembly Step 11 Insert Bench Rear Frame (15) onto Bench Main Frame (13) and secure using two Nuts (144), four Washers (143), and two Bolts (133). Attach Bench Front Frame (14) on to Bench Main Frame (13) using two Nuts (144), four Washers (143), and two Bolts (136). Figure 11 25 Assembly Step 12 Attach Bench Seat Pad Support (16) to Bench Main Frame (13) using one Nut (126), one Washer (125), and one Bolt (132). Insert Bench Seat Pad Adjustment Bar (64) into Bench Main Frame (13) and secure using one Washer (125) and one Nut (126). Attach Spring (66) to Bench Main Frame (13) and Bench Seat Pad Adjustment Bar (64). Note: Make sure adjustment bar is installed into adjustable slots on Bench Seat Pad Support. Figure 12 26 Assembly Step 13 Attach Bench Back Pad Support (17) to Bench Main Frame (13) using one Nut (126), two Washers (125), and one Bolt (132). Attach Bench Back Pad Adjustment Frame (39) to Bench Back Pad Support (17) using one Nut (126), to Washers (125), and one Bolt (132). Figure 13 27 Assembly Step 14 Attach Bench Seat Pad (48) and Bench Back Pad (49) using four Washers (143) and four Bolts (138). Insert Foam Shaft (40) into Foam Adjustable Bracket (18). Next, attach Upholstered Roller Pads (58) using the following hardware: four Plastic Washers (90), two Chrome Washers (101), two Washers (143), two Spring Washers (119), and two Allen Bolts (128). See Figure 14 for details. Figure 14 28 Assembly Step 15 Attach Left and Right Squat Arms (36 &37) to the Press Arm Assembly (35) using two Safety Pins (73). Next, slide Upholstered Roller Pad (58) onto each Squat Arm (36 & 37) and secure using two Plastic Washers (90), two Chrome Washers (101), two Washers (143), two Spring Washers (119), and two Allen Bolts (128). Figure 15 29 Assembly Step 16 Attach Back Pad (51) to Back Pad Adjustment Bracket (28) using two Washers (143) and two Bolts (140). Attach Seat Pad (50) to Seat Pad Support (27) using two Washers (143) and two Allen Bolts (127). Slide both assemblies into receptacles as shown in Figure 16. Figure 16 30 Assembly Step 17 Slide two Upholstered Roller Pads (58) onto Foam Frames (25 & 26) and secure using two Big Plugs (89). Slide the Long Foam Tube (34) through the hole in Seat Pad Support (27). Next, slide two Plastic Washers (90), two Upholstered Roller Pads (58), and two Big Plugs (89) onto each end of Long Foam Tube (34). Next, slide two Upholstered Roller Pads (58) onto each side of Leg Hold Frames (29 & 30) and secure using two Big Plugs (89). Figure 17 31 Assembly Step 18 Note: Stretch all cables out completely and make sure all twisting is removed before installing. Install Lat Cable (110) as detailed in Figure 18. Follow dotted lines to identify exact location of pulleys. See Page 43 “Cable View” for more detail. Start by threading cable end into Top Plate (55). You will need the following for installation: Bolt (134) - Qty. 2 Pulley (57) - Qty. 7 Bolt (135) - Qty. 1 Cable (110) - Qty. 1 Bolt (136) - Qty. 1 Nut (144) - Qty. 7 Bolt (137) - Qty. 1 Long Pulley Spacer (123) - Qty. 4 Bolt (141) - Qty. 2 Longer Pulley Spacer (121) - Qty. 4 Cable Retainer Bracket (46) - Qty. 1 Figure 18 32 Assembly Step 19 Note: This step is only used if you do not have the Leg Press 2 attachment. Use the Cable Adapter (124) in place of the pulley. Note: Stretch all cables out completely and make sure all twisting is removed before installing. Install Leg Press Cable Substitute (113) as detailed in Figure 19. Follow dotted lines to identify exact location of pulleys. You will need the following for installation: Cable Adapter (124) - Qty. 1 Cable (113) - Qty. 1 Bolt (139) - Qty. 1 Washers (143) - Qty. 2 Nylon Locknut (143) - Qty. 1 Figure 19 33 Assembly Step 20 Note: Stretch all cables out completely and make sure all twisting is removed before installing. Install Low Row Cable (111) as detailed in Figure 20. Follow dotted lines to identify exact location of pulleys. See Page 43 “Cable View” for more detail. Start by installing cable under the pulley at Leg Extension location. You will need the following for installation: Bolt (134) - Qty. 1 Pulley (57) - Qty. 6 Bolt (136) - Qty. 1 Cable (111) - Qty. 1 Bolt (137) - Qty 1 Nut (144) - Qty. 6 Bolt (138) - Qty. 1 Long Pulley Spacer (123) - Qty. 4 Bolt (141) - Qty. 2 Longer Pulley Spacer (121) - Qty. 2 Washer (143) - Qty. 12 Short Pulley Spacer (122) - Qty. 2 Cable Retainer Bracket (46) - Qty. 1 Figure 20 34 Assembly Step 21 Note: Stretch all cables out completely and make sure all twisting is removed before installing. Install Pec Dec Cable (112) as detailed in Figure 21. Follow dotted lines to identify exact location of pulleys. See Page 43 “Cable View” for more detail. You will need the following for installation: Cable (112) - Qty. 1 Pulley (57) - Qty. 3 Bolt (141) - Qty. 3 Washers (143) - Qty. 6 Nut (144) - Qty. 3 Philips Screw (103) - Qty. 2 Figure 21 35 Assembly Step 22 Note: Stretch all cables out completely and make sure all twisting is removed before installing. Install Long Chest Cable (114) as detailed in Figure 22. Follow dotted lines to identify exact location of pulleys. See Page 43 “Cable View” for more detail. Start by installing cable into the “Press Station” weight stack. You will need the following for installation: Pulley (57) - Qty. 2 Cable (114) - Qty. 1 Nut (144) - Qty. 3 Washer (134) - Qty. 4 Bolt (141) - Qty. 3 Figure 22 36 Assembly Step 23 Note: Stretch all cables out completely and make sure all twisting is removed before installing. Install Short Chest Cable (115) as detailed in Figure 23. Follow dotted lines to identify exact location of pulleys. See Page 43 “Cable View” for more detail. Start by threading the cable into the floating pulley bracket. You will need the following for installation: Pulley (57) - Qty. 1 Cable (115) - Qty. 1 Nut (144) - Qty. 2 Washer (134) - Qty. 2 Bolt (141) - Qty. 2 Figure 23 Floating Pulley 37 Assembly Step 24 Connect Long Lat Bar (43) to the Lat Cable (110) using two Gear Hooks (87) and Short Chain (88). Connect Ab Strap (60) or Lat Strap (61) to Low Row Cable (111) using one Gear Hook (87). Connect Short Lat Bar (44) or Ankle Strap (62) to Low Row Cable (111) using two Gear Hooks (87) and Long Chain (116). Figure 24 38 Assembly Step 25 Install Weight Shrouds (41) to the left and right side of the weight stacks using four Washers (117) and four Allen Bolts (98). Install Weight Shroud (42) to the center of both weight stacks and secure using four Washers (117) and four Allen Bolts (98). Locate placard inside packing material and place on the center Weight Shroud (42). Figure 25a Figure 25 Figure 25a Note: Tighten all hardware securely. 39 Assembly Congratulations! You have completed the assembly of your new KPS-2050. 40 Weight Ratios KPS-2050 Weight(lbs) 10 15 20 25 30 35 45 55 65 75 85 95 105 115 125 140 155 170 185 200 100% 10 15 20 25 30 35 45 55 65 75 85 95 105 115 125 140 155 170 185 200 Weight Ratios 95% 90% 9.5 9 14.25 13.5 19 18 23.75 22.5 28.5 27 33.25 31.5 42.75 40.5 52.25 49.5 61.75 58.5 71.25 67.5 80.75 76.5 90.25 85.5 99.75 94.5 109.25 103.5 118.75 112.5 133 126 147.25 139.5 161.5 153 175.75 166.5 190 180 41 65% 6.5 9.75 13 16.25 19.5 22.75 29.25 35.75 42.25 48.75 55.25 61.75 68.25 74.75 81.25 91 100.75 110.5 120.25 130 45% 4.5 6.75 9 11.25 13.5 15.75 20.25 24.75 29.25 33.75 38.25 42.75 47.25 51.75 56.25 63 69.75 76.5 83.25 90 Weight Stack Sticker Placement Your new POWER SYSTEM unit can be purchased with either a 200 LB or 250 LB weight stack. Depending on which weight stack you have purchased will determine which weight stack sticker numbers will be used. The weight stack images below show which weight stack sticker numbers are to be used on your weight stack. Please note that these stickers should not be put on until the entire unit has been assembled and all bolts and nuts have been tightened. 200 LB Stack 250 LB Stack 10 10 15 20 20 30 25 40 30 50 35 60 45 70 55 80 65 90 75 100 85 115 95 130 105 145 115 160 125 175 140 190 155 205 170 220 185 235 200 250 42 Cable View 43 Top View 44 Exploded View 45 Parts List REF# KEYS PART# 1 223-00258 2 223-00259 3 223-00260 4 223-00261 5 223-00262 6 223-00263 7 223-00264 8 219-00265 9 223-00266 10 223-00267 11 223-00268 12 223-00269 13 223-00270 14 223-00271 15 223-00272 16 219-00285 17 223-00273 18 219-00286 19 223-00248 20 223-00244 21 223-00241 22 223-00243 23 223-00242 24 219-00272 25 219-00266 26 219-00265 27 223-00274 28 219-00287 29 219-00270 30 219-00271 31 219-00274 32 219-00275 33 219-00273 34 219-00031 35 223-00021 36 223-00011 37 223-00010 38 230-00021 39 219-00034 40 219-00288 41 223-00275 42 223-00276 43 223-00092 44 219-00136 45 210-00097 46 219-00281 47 223-00247 48 228-00087 49 228-00086 50 228-00084 51 228-00085 52 219-00277 53 219-00278 54 219-00279 55 223-00031 56 210-00002 57 219-00006 58 228-00077 59 210-00029 60 210-00099 61 210-00061 62 210-00059 63 206-00103 64 210-00100 65 206-00147 66 202-00156 67 202-00149 68 202-00157 69 206-00146 70 206-00148 71 206-00111 72 206-00053 73 210-00001 74 210-00030 75 202-00030 76 206-00143 DESCRIPTION Rear Frame Up Frame Rear Upright Right Base Frame Right Top Frame Seat Pad Support Receptacle Main Upright Left Base Frame Left Top Frame Press Arm Support Press Station Base Frame Chest Press Cam Bench Main Frame Bench Front Frame Bench Rear Frame Bench Seat Pad Support Bench Back Pad Support Foam Adjustable Bracket Front Upright Leg Extension Lever Pec Dec mount Right Pec Dec Arm Left Pec Dec Arm Pec Dec Handle Bar Foam Frame w/o Shaft Foam Frame w/Shaft Seat Pad Support Back Pad ADJ. Bracket Right Leg Hold Leg Frame Left Leg Hold Leg Frame Pulley Bracket Block Pulley Bracket Pulley Bracket w/Shaft Long Foam Tube Press Arm Right Squat Arm Left Squat Arm Press Station Shaft Bench Back Pad Adj. Frame Foam Shaft Weight Shroud A Weight Shroud B Long Lat Bar Short Lat Bar Adjustable Stopper Cable Retainer Bracket Guide Rod Bench Seat Pad Bench Back Pad Seat Pad Back Pad 15LB Plate 10LB Plate 5LB Plate Top Plate Weight Pin Pulley Upholstered Roller Pad 100*22*180 Pop Pin (Locking) Ab Strap Lat Strap Ankle Strap Grip Bench Seat Pad Adj. Bar Nylon Handball Spring ij1.5*ij13*43 Spring ij1*ij13*38 Pin Shaft Pin Knob Nylon Spacer Grip Handle Grip Safety Pin Pop Pin Pillow black Bearing Pec Dec Stop Bumper KPS-2050 Parts List QTY. 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 2 1 1 1 1 2 4 1 1 1 1 10 18 10 2 2 19 10 2 1 2 1 4 1 1 1 1 1 1 1 1 3 2 1 2 2 REF# KEYS PART# 77 202-00024 78 206-00150 79 206-00151 80 206-00061 81 206-00099 82 202-00140 83 202-00155 84 202-00142 85 202-00146 86 230-00022 87 210-00098 88 229-00037 89 206-00141 90 206-00134 91 206-00005 92 206-00006 93 206-00001 94 206-00140 95 206-00020 96 206-00139 97 202-00143 98 202-00017 99 206-00026 100 206-00153 101 202-00129 102 202-00145 103 202-00102 104 202-00016 105 202-00023 106 206-00154 107 206-00102 108 206-00004 109 206-00136 110 229-00053 111 229-00054 112 229-00050 113 229-00049 114 229-00055 115 229-00056 116 229-00057 117 202-00158 118 202-00134 119 202-00100 120 202-00141 121 202-00140 122 202-00025 123 202-00071 124 210-00093 125 202-00127 126 202-00092 127 202-00125 128 202-00087 129 202-00130 130 202-00077 131 202-00126 132 202-00175 133 202-00079 134 202-00080 135 202-00082 136 202-00081 137 202-00083 138 202-00084 139 202-00159 140 202-00085 141 202-00086 142 202-00160 143 202-00128 144 202-00091 145 214-00001 146 202-00132 147 202-00133 148 210-00094 150 219-00276 151 202-00121 152 202-00129 46 DESCRIPTION Bearing ID25 Caster Black Plastic End Cap w/Groove Base Pad End Cap Bumper "U" Shape Pin Spring ij1*ij8*35 Nut M6 Slip Tension Pin Shaft For Leg Extension Gear Hook Short Chain Big Plug ij25.4 Plastic Washer Plug ij50 Plug40*80 Plug76.2*50.8 Plug50.8 Plug44.5 Plug50*25 Screw M8*6 Allen Bolt M8*15 Weight Stack Bumper Rubber Mat Chrome Wash ij38*ij11*2 Big Washer ij56.5*ij10.5*5 Philip Screw M4*20 Bronze Bushing ID25.4 Bronze Bushing ID12.2 Button Pad Plug ij32 Plug ij25 Rubber Stopper Lat Cable Low Row/Abdominal Cable Pec Dec Cable Leg Press Substitute Cable Long Chest Cable Short Chest Cable Long Chain Washer ij9*ij22*2 Spring Washer 8 Spring Washer 10 Bronze Bushing ID16 Longer Pulley Spacer Short Pulley Spacer Long Pulley Spacer Cable Adaptor Washer ij13*ij24*1.5 Nut M12 Allen Bolt M10*50 Allen Bolt M10*25 Washer ij38*ij11*2 Bolt M12*85 Bolt M12*80 Bolt M12*125 Bolt M10*105 Bolt M10*85 Bolt M10*80 Bolt M10*75 Bolt M10*70 Bolt M10*65 Bolt M10*60 Bolt M10*50 Bolt M10*45 Allen Bolt M10*30 Washer ij11*ij20*2 Nut M10 Decal Weight Number Hex Key 6 Hex Key 4 Lube Selector Rod Screw Bolt M12*35 Hex Nut M10 QTY. 4 2 4 8 1 1 1 1 1 1 7 1 6 8 2 2 3 3 3 8 3 9 4 1 9 2 2 8 6 14 2 2 2 1 1 1 1 1 1 1 9 1 15 2 6 2 8 1 25 13 2 10 1 4 4 4 2 6 3 12 11 5 1 2 14 4 116 52 2 1 1 1 2 2 1 Warranty Information KEYS FITNESS PRODUCTS, L.P. POWER SYSTEM SERIES LIFETIME WARRANTY This Warranty applies in the United States and Canada to products manufactured or distributed by Keys Fitness Products, LP (“Keys”) under the KEYS brand name. The warranty period to the original purchaser is lifetime of the original purchaser. Keys warrants that the Product you have purchased for non-commercial, personal, family, or household use from Keys or from an authorized Keys reseller is free from defects in materials or workmanship under normal use during the warranty period. Your sales receipt, showing the date of purchase of the Product, is your proof of purchase. This warranty only extends to you, the original purchaser. It is not transferable to anyone who subsequently purchases the Product from you. It excludes expendable parts (wear items). Wear items pertain to components that might need to be replaced due to normal wear and tear. These items vary per product but will include grips, chains, cables, pads, upholstery, pulleys, bearings, etc. Please contact a Keys customer service representative for specifics on wear items. This Warranty becomes VALID ONLY if the product is purchased through a Keys Fitness authorized dealer unless otherwise authorized by Keys Fitness in writing and must be assembled / installed according to the instructions included with the Product. In a light institutional setting, Keys will extend a one year warranty to the the original purchaser. During the warranty period Keys will repair or replace (at Keys' option) the product if it becomes defective, malfunctions, or otherwise fails to conform with this Warranty under normal use. In repairing the Product, Keys may replace defective parts, or at the option of Keys, serviceable used parts that are equivalent to new parts in performance. All exchanged parts and Products replaced under this warranty will become the property of Keys. Keys reserves the right to change manufacturers of any part to cover any existing warranty. This warranty DOES NOT COVER shipping charges, export taxes, custom duties and taxes, or any other charges associated with transportation of the parts or Product. To obtain warranty service, you must contact a Keys authorized retailer, service technician or Keys Fitness at our phone number located in this manual. Any parts determined to be defective must be returned to Keys to obtain warranty service. You must prepay any shipping charges, export taxes, custom duties and taxes, or any other charges associated with transportation of the parts or Product. In addition, you are responsible for insuring any parts or Product shipped or returned. You assume the risk of loss during shipment. You must present Keys with proof-of-purchase documents (including the date of purchase). Any evidence of alteration, erasing or forgery of proof-of-purchase documents will be cause to void this Warranty. This Warranty does not extend to any product not purchased from Keys or from an authorized Keys reseller. This Limited Warranty does not extend to any Product that has been damaged or rendered defective; (a) as a result of accident, misuse, or abuse; (b) by the use of parts not manufactured or sold by Keys; (c) by modification of the Product or normal wear and tear; (d) operation on incorrect power supplies; or (e) as a result of service by anyone other than Keys, or an authorized Keys warranty service provider. Product on which the serial number has been defaced or removed is not eligible for warranty service. Should any Product submitted for warranty service be found ineligible, an estimate of repair cost will be furnished and the repair will be made if requested by you upon Keys' receipt of payment or acceptable arrangements for payment. EXCEPT AS EXPRESSLY SET FORTH IN THIS WARRANTY, KEYS MAKES NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. KEYS EXPRESSLY DISCLAIMS ALL WARRANTIES NOT STATED IN THIS LIMITED WARRANTY. ANY IMPLIED WARRANTIES THAT MAY BE IMPOSED BY LAW ARE LIMITED TO THE TERMS OF THIS LIMITED WARRANTY. NEITHER KEYS NOR ANY OF ITS AFFILIATES SHALL BE RESPONSIBLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS OR THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS OR EXCLUSION MAY NOT APPLY TO YOU. This Limited Warranty gives you specific legal rights and you may also have other rights that may vary from state to state. This is the only express warranty applicable to Keys-branded products. Keys neither assumes nor authorizes anyone to assume for it any other express warranty. PLEASE SEND IN THE INCLUDED WARRANTY CARD OR REGISTER ON-LINE AT www.keysfitness.com WITHIN TEN (10) DAYS OF PURCHASE TO REGISTER YOUR UNIT WITH KEYS FITNESS PRODUCTS, LP. MAIL WARRANTY CARD TO: KEYS FITNESS PRODUCTS, PO BOX 551239, DALLAS, TX 75355 47 Customer Service 1.888.340.0482 Keys Fitness 4009 Distribution Drive Suite 250 Garland, TX 75041 www.keysfitness.com
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.3 Linearized : Yes Create Date : 2004:09:07 15:38:37-05:00 Modify Date : 2004:09:07 15:38:37-05:00 Page Count : 48 Creation Date : 2004:09:07 20:38:37Z Mod Date : 2004:09:07 20:38:37Z Producer : Acrobat Distiller 5.0.5 (Windows) Author : striplett Metadata Date : 2004:09:07 20:38:37Z Creator : striplett Title : kps-2050.qxdEXIF Metadata provided by EXIF.tools