Kidde Fire Systems Smoke Alarm K 45 9049 Users Manual

: Kidde-Fire-Systems Kidde-Fire-Systems-Kidde-Fire-Systems-Smoke-Alarm-K-45-9049-Users-Manual-568182 kidde-fire-systems-kidde-fire-systems-smoke-alarm-k-45-9049-users-manual-568182 kidde-fire-systems pdf

Open the PDF directly: View PDF .
Page Count: 2

A UTC Fire & Security Company

Effective: April 2008

K-45-9049

Kidde Engineered Fire

Suppression System

Designed for use with 3M™ Novec 1230™ Fire Protection Fluid

Explosion Proof Solenoid,

Electric Control Head Data Sheet

FEATURES

• Explosion Proof:

– UL Listed as Suitable for Hazardous Locations

Class I Div 1 Groups C and D

Class II Div 1 Groups E, F and G

• FM Approved

• Compatible with UL Listed and FM Approved

Suppression Systems:

– FM-200® Systems, Including the ADS

– Carbon Dioxide Systems

–FE-13

™ Systems

•Operated By:

– Control Panel

– Mechanical Manual Actuator

• Nominal 24 Vdc Operation

• Low Current Consumption

• Operates:

– Cylinder Valves

–Stop Valves

– Directional Valves

• Wide Operating Temperature Range

• Rugged Brass Body

P/N: 81-100000-001

DESCRIPTION

The Explosion Proof Control Head is designed to operate

FM-200®, ADS, Carbon Dioxide and FE-13™ cylinder

valves, stop valves and directional valves. The Explosion

Proof Control Head can be operated electronically from

the Detection and Control system, or by local manual

operation via an affixed manual control head. The Explo-

sion Proof Control Head has a continuous current draw,

which must be accommodated for at the Control Panel.

The actuating pin latches in the released position and

must be mechanically reset prior to re-arming the sys-

tem.

A suitable Control Panel, Listed and/or Approved for use

with the Explosion Proof Control Head, shall be provided

for supervision of the releasing circuit per NFPA require-

ments.

The Explosion Proof Control Head is designed and rated

for use in the following hazardous areas: Class I Division

1 Group C and D and Class II Division 1 Group E, F and

G.

Figure 1. Assembly Drawing

INSTALLATION

The Explosion Proof Control Head can be mounted

directly on either the cylinder valve, stop/directional

valve.

Tighten the swivel nut securely in place.

7.8 in. (198 mm)

3.0 in.

(76 mm)

WARNING

Care should be taken to ensure that

the actuating pin is in the set position

when attaching the control head to the

cylinder or the stop/directional valve.

Accidental system discharge could

occur, which could cause property

damage, personal injury and/or death.

A UTC Fire & Security Company

400 Main Street

Ashland, MA 01721

Ph: 508.881.2000

Fax: 508.881.8920

www.kiddefiresystems.com

This literature is provided for informational purposes only. KIDDE-FENWAL, INC.

assumes no responsibility for the product’s suitability for a particular application. The

product must be properly applied to work correctly.

If you need more information on this product, or if you have a particular problem or ques-

tion, contact KIDDE-FENWAL, INC., Ashland, MA 01721. Telephone: (508) 881-2000.

K-45-9049 Rev AC © 2008 Kidde-Fenwal Inc. Printed in USA

When installing the Explosion Proof Control Head in haz-

ardous locations, wiring connections must be terminated

in explosion proof junction boxes.

The lead wires must be connected using the indicated

polarity (red to positive, black to negative) in order to

obtain correct operation.

MAINTENANCE

Regular scheduled maintenance should be performed on

the Explosion Proof Control Head to ensure that the unit

operates correctly if and when required.

MONTHLY

The Explosion Proof Control Head should be inspected

for any signs of physical damage, deterioration, corro-

sion, distortion, cracks, dirt ingress and loose couplings.

Tighten any loose couplings. Replace damaged or miss-

ing caps. Replace control head if damage is found.

Ensure that all explosion proof control heads are in the

“set” position.

SEMI-ANNUALLY

The Explosion Proof Control Head should be tested for

proper operation.

Remove control heads from all master cylinders within

the hazard area being tested. Let the Explosion Proof

Control Head hang freely from the flexible electrical con-

duit connections. Operate the Explosion Proof Control

Head, either by actuation at the system control panel or

via manual operation of an electric pull station. Ensure

that the control head has operated. Observe that the

actuating pin has moved to the fully released position. If

any control heads have not operated, check circuit for

electric continuity. Replace all damaged control heads.

Repeat operation test if any control heads have been

replaced. Replace any damaged control head, which fails

to reset properly. Make certain that electric control heads

are in the set position before reconnecting to agent cylin-

ders. Reattach all control heads to threaded ports on cyl-

inder valves and tighten swivel nuts securely.

SPECIFICATIONS

Part Number: 81-100000-001

Applications: FM-200, ADS, Carbon Dioxide

and FE-13 Suppression Sys-

tems

Approval/Listing:

Releasing Device– UL, FM

HazLoc– UL, FM

HazLoc Ratings: Class I Division 1 Group C

and D

Class II Division 1 Group E, F

and G

Operating Voltage: 18 Vdc @ 0.20 A to

30 Vdc @ 0.50 A

Current Draw:

At 24 Vdc– 270 mA continuous

At 30 Vdc– 500 mA continuous

Wiring Connections:

Wire Size– 18 AWG

Lead Length– 36 in. (914 mm)

Ambient Temperature: -40°F to 130°F (-40°C to 55°C)

Construction:

Material– Brass body

Weight– 8.1 lb. (3.7 kg)

Dimensions: 3 in. D x 7.8 in. L

(76 mm D x 198 mm L)

ORDERING INFORMATION

WARNING

All Explosion Proof Control Heads

should be removed from agent cylin-

ders (Carbon Dioxide, FM-200 or FE-

13) to avoid accidental system dis-

charge, which could cause property

damage, personal injury and/or death.

Part Number Description

81-100000-001 Explosion Proof Solenoid

(Electric Control Head)

870652 Mechanical Manual Actuator

81-129958-001 Reset Tool Assembly