Kidde Kn Cosm Ica Users Manual

2014-12-11

: Kidde Kidde-Kn-Cosm-Ica-Users-Manual-120407 kidde-kn-cosm-ica-users-manual-120407 kidde pdf

Open the PDF directly: View PDF .
Page Count: 18

Download
Open PDF In Browser	View PDF

810-1692_RevD_119-133_MAN_ENG

10/7/03

4:41 PM

Page 34

For your convenience, write down the following information. If you call
our consumer hotline, these are the first questions you will be asked:
Alarm Model Number (located on back of alarm):

Date of Manufacture (located on the back of the alarm):

120 V AC and 9 V Battery Backup
(model KN-COSM-IBCA only)

Date of Purchase:

Where Purchased:

Alarm Assembly Number (located on the back of the alarm):

Maximum protection
only an Interconnectable System can offer:
Every floor... every living space... any place where a crisis could
begin, needs the added security of an interconnectable life safety
warning system! ANY unit that senses a problem automatically
triggers ALL units through-out the home immediately, allowing
extra time for escape.
Installing the Interconnectable System is simple:
Unlike competitive products, the Interconnectable System requires
no complex wiring or relay switches to separate alarms. Just direct
connect and you're done!

Combination Smoke &
Carbon Monoxide Alarm
with Voice Alarm System, Hush®, and Peak Level Memory

Alarm Manual
Model
KN-COSM-ICA

Model
KN-COSM-IBCA

This Smoke & CO Alarm interconnects with up to 24 devices
directly. Use with Kidde Pro, Fyrnetics and Lifesaver Smoke
Alarms, including:
•1235CA Series •1285CA Series •PI2000CA •KN-COSM-ICA
•1275CA Series •PE120CA
•HD135
•KN-COSM-IBCA
For more information about compatible interconnect units and their
functionality in an interconnect system, visit our web site at:
www.kidde.ca

130 Esna Park Drive, Markham ON L3R 1E3
Consumer Hotline: 1-800-880-6788
www.kidde.ca
Custom Assembled in China with U.S. and Foreign Components. Patents Pending

SINGLE AND/OR MULTIPLE STATION
SMOKE ALARM
SINGLE AND/OR MULTIPLE STATION
CARBON MONOXIDE ALARM

SINGLE AND/OR MULTIPLE STATION
CARBON MONOXIDE ALARM

810-1692_RevD_119-133_MAN_ENG

10/7/03

4:41 PM

Page 2

Contents

Introduction

Introduction . . . . . . . . . . . . . . . . . . . . . . . . 1

Thank you for purchasing the Kidde
Combination Smoke and Carbon Monoxide Alarm.

Illustrations . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . 8-15
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-19
Alarm Removal . . . . . . . . . . . . . . . . . . . . . . 20
Battery Replacement . . . . . . . . . . . . . . . . . . 20-21
Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . 22
Carbon Monoxide Safety. . . . . . . . . . . . . . . 23-27
Fire Safety. . . . . . . . . . . . . . . . . . . . . . . . . . . 28-30
Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . 31-32

Model # KN-COSM-IBCA (with battery backup)
Model # KN-COSM-ICA (without battery backup)
This unit is suitable as a Single Station and/or Multiple
Station alarm (interconnects with up to 24 devices),
and has a five-year limited warranty.
IMPORTANT: This unit is only approved to
interconnect with the Kidde line of products. It is not
approved to interconnect with any other manufacturer’s
products.
Please take a few minutes to thoroughly read this
user’s guide, and save for future reference. Teach
children how to respond to the alarms, and that they
should never play with the unit.
Your Kidde Smoke/CO Alarm was designed to detect
both smoke and carbon monoxide from any source of
combustion in a residential environment. It is not
designed for use in a recreational vehicle (RV) or boat.
If you have any questions about the operation or
installation of your alarm, please call our toll free
Consumer Hotline at 1-800-880-6788.
The guide on Page 29 will help you determine the
correct location of safety products that will help keep
your home a safer place.

Illustrations

BACK

FRONT
Test/Reset/
Hush®
Button

Alarm
Sounder

Red LED Light

Green LED Light

• Permanent, independent smoke and carbon
monoxide sensors (ionization and electrochemical).

• Voice Message System that alerts user to the
following additional conditions:

• Powered by 120 V AC (60 Hz, 25 mA max) QuickConnect wire harness. Model KN-COSM-IBCA is
also equipped with a 9 V battery backup.

• System announces, "Hush® mode on! Mode Hush®
activé!" when the unit is first put into Hush® Mode.

• Interconnectable to other alarms and safety
accessories (see Page 16 for details).
• Loud 85 decibel alarm.
•

• System announces, "Hush® mode cancelled! Mode
Hush® annulé!" when unit resumes normal
operation after Hush® Mode has been cancelled.
• System announces, "Caution! Attention!" when the
unit has detected CO concentrations of 100 ppm or
higher.
• One "chirp" every 30 seconds indicates that the
alarm is malfunctioning. If this occurs call the
Consumer Hotline at 1-800-880-6788.
• Peak Level Memory Feature which alerts user when
the unit has detected CO concentrations of 100 ppm
or greater (see Page 17).
• Alarm Memory Feature that gives visual indication
when the alarm has sensed a hazardous condition.
• Green and red LED lights that indicate normal
operation and alarm status (see Page 18 for details).
• Tamper Resist Feature that deters children and others
from removing the alarm (see Page 19).
• For initial installation, model KN-COSM-IBCA
includes a pre-installed 9 V battery, and a battery
pull tab that allows for easy connection. Simply pull
the tab out, and the battery backup is connected!
• Model KN-COSM-IBCA is equipped with a battery
reminder tab that prohibits installation when a
battery is not present.
• Smoke alarm takes precedence when both smoke
and carbon monoxide are present.
• Seven (7) years after initial power up, this unit will
"chirp" every 30 seconds to indicate that it is time to
replace the alarm.

810-1692_RevD_119-133_MAN_ENG

10/7/03

4:41 PM

Features

Smoke Alarm

• Smoke alarms cannot provide an alarm if smoke does
not reach the alarm. Therefore, smoke alarms may not
sense fires starting in chimneys, walls, on roofs, on the
other side of a closed door or on a different floor.

The smoke alarm constantly monitors the air for products of
combustion that are produced when something is burning or
smoldering. When smoke particles in the smoke sensor reach
a specified concentration, the alarm/voice message warning
system will sound, accompanied by the flashing red LED light.
NOTE: The smoke alarm takes precedence when both
smoke and carbon monoxide are present.
WARNING: PLEASE READ CAREFULLY AND THOROUGHLY
NFPA Standard 72 states: Life safety from fire in residential
occupancies is based primarily on early notification to
occupants of the need to escape, followed by the
appropriate egress actions by those occupants. Fire warning
systems for dwelling units are capable of protecting about
half of the occupants in potentially fatal fires. Victims are
often intimate with the fire, too old or young, or physically
or mentally impaired such that they cannot escape even
when warned early enough that escape should be possible.
For these people, other strategies such as protection-in-place
or assisted escape or rescue are necessary.
• Smoke alarms are devices that can provide early warning
of possible fires at a reasonable cost, however, alarms
have sensing limitations. Ionization type alarms offer a
broad range of fire sensing capabilities but are better at
detecting fast flaming fires than slow smoldering fires.
Photoelectric alarms sense smoldering fires better than
flaming fires. Home fires develop in different ways and
are often unpredictable. Neither type of alarm
(photoelectric or ionization) is always best, and a
given alarm may not always provide warning of a fire.
• A battery powered alarm must have a battery of the
specified type, in good condition and installed properly.
• AC powered alarms (without battery backup) will
not operate if the AC power has been cut off, such
as by an electrical fire or an open fuse.
• Smoke alarms must be tested regularly to make sure
the batteries and the alarm circuits are in good
operating condition.

Page 6

• If the alarm is located outside the bedroom or on a
different floor, it may not wake up a sound sleeper.
• The use of alcohol or drugs may also impair one’s
ability to hear the smoke alarm. For maximum
protection, a smoke alarm should be installed in
each sleeping area on every level of a home.
Carbon Monoxide (CO) Alarm
The carbon monoxide (CO) alarm constantly monitors the
air for the presence of CO. It will alarm when there are
high levels of CO present, and when there are low levels
of CO present over a longer period of time (see Page 24
for alarm times). When a CO condition matches either of
these situations, the alarm/voice message warning system
will sound, accompanied by the flashing red LED light.
The carbon monoxide sensor uses an electrochemical technology.
CAUTION: This alarm will only indicate the presence of
carbon monoxide gas at the sensor. Carbon monoxide gas
may be present in other areas.
This device is designed to protect individuals from the
acute effects of carbon monoxide exposure. It will not
fully safeguard individuals with specific medical
conditions. If in doubt, consult a medical practitioner.
Installation of the device should not be used as a
substitute for proper installation, use, and maintenance
of fuel-burning appliances, including appropriate
ventilation and exhaust systems.
Individuals with medical problems may consider using
warning devices which provide audible and visual signals
for carbon monoxide concentrations under 30 ppm.
Never ignore the sound of the alarm!
Determining what type of alarm has sounded is easy
with the Kidde Combination Smoke/CO Alarm. The
voice message warning system will inform you of the
type of hazard occurring.

Recommended Installation Locations
WARNING: This product is intended for use in
ordinary indoor locations of family living units.
It is not designed to measure compliance with
commercial or industrial standards.
IMPORTANT: This alarm must be mounted on a ceiling
or wall. It was not designed for use as a tabletop device.
Install only as directed.
Kidde recommends the installation of a Smoke/CO
Alarm in the following locations. For maximum
protection we suggest an alarm be installed on each
level of a multilevel home, every bedroom, hallways,
finished attics and basements. Put alarms at both ends
of bedroom, hallway or large room if it is more than
9.1 m (30’) long. If you have only one alarm, ensure it
is placed in the hallway outside of the main sleeping
area, or in the main bedroom. Verify the alarm can be
heard in all sleeping areas.
Locate an alarm in every room where someone sleeps
with the door closed. The closed door may prevent
the alarm from waking the sleeper. Smoke, heat and
combustion products rise to the ceiling and spread
horizontally. Mounting the alarm on the ceiling in the
center of the room places it closest to all points in the
room.
Ceiling mounting is preferred in ordinary residential
construction. When mounting an alarm on the ceiling,
locate it at a minimum of 10 cm (4") from the side wall
(see Diagram A). If installing the alarm on the wall,
use an inside wall with the top edge of the alarm at a
minimum of 10 cm (4") and a maximum of
30.5 cm (12") below the ceiling (see Diagram A).

810-1692_RevD_119-133_MAN_ENG

10/7/03

4:41 PM

Installation

Sloped Ceilings

Locations To Avoid

Install Smoke Alarms on sloped, peaked or cathedral
ceilings at, or within 0.9 m (3’) of the highest point
(measured horizontally). Smoke alarms in rooms with
ceiling slopes greater than 0.3 m - 2.4 m (1’ to 8’)
horizontally should be located on the high side of the
room. Do not place the alarm in the peak of an “A”
frame type ceiling (see Diagram B).

WARNING: Do not install in garages, kitchens, furnace
rooms or bathrooms! Install at least 1.5 m (5’) away
from any fuel burning appliance.

Mobile Homes
Mobile homes built within the last five to seven years
are designed to be energy efficient. Install Smoke/CO
alarms as recommended above (refer to Recommended
Installation Instructions and Diagram A).
In mobile homes that are not well insulated, extreme
heat or cold can be transferred from the outside to the
inside through poorly insulated walls and roof. This
may cause a thermal barrier, which can prevent smoke
from reaching an alarm mounted on the ceiling. In
such mobile homes, install the Smoke/CO Alarm on an
inside wall with the top edge of the alarm at a
minimum of 10 cm (4”) and a maximum of
30.5 cm (12”) below the ceiling (see Diagram A). If
you are not sure about the insulation in your mobile
home, or if you notice that the outer walls and ceiling
are either hot or cold, install the alarm on an inside
wall only!

Page 10

Do not install within 0.9 m (3’) of the following:
The door to a kitchen, or a bathroom that contains a
tub or shower, forced air ducts used for heating or
cooling, ceiling or whole house ventilating fans, or
other high air flow areas. Avoid excessively dusty,
dirty or greasy areas. Dust, grease or household
chemicals can contaminate the alarm’s sensors, causing
it to not operate properly.
Place the alarm where drapes or other objects will not
block the sensor. Smoke and CO must be able to
reach the sensors to accurately detect these conditions.
Do not install in peaks of vaulted ceilings, “A” frame
ceilings or gabled roofs. Keep out of damp and humid
areas. Do not place near a diaper pail.
Install at least 30.5 cm (12”) away from fluorescent
lights as electronic noise may cause nuisance alarms.
Do not place in direct sunlight and keep out of insect
infested areas. Extreme temperatures will effect the
sensitivity of the Smoke/CO Alarm. Do not install in
areas where the temperature is colder than
4.4°C (40°F) or hotter than 37.8°C (100°F). Do not
install in areas where the relative humidity (RH) is
greater than 85%. Place away from doors and
windows that open to the outside.

Installation
Wiring
Wiring Requirements:
• This Smoke/CO Alarm should be installed on a CSA
listed or recognized junction box. All connections
should be made by a qualified electrician and must
conform to codes having jurisdiction in your area.
• The appropriate power source is 120 V AC Single
Phase supplied from a non-switchable circuit, which
is not protected by a ground fault interrupter.
• The alarm should not be operated on power derived
from a square wave or modified square wave
inverter. These power sources produce high peak
voltages that will damage the alarm.

Installation
devices and/or relay modules (see Page 16 for
details on interconnecting Kidde devices).
• The maximum wire run distance between the first
and last unit in an interconnected system is 305 m
(1000’).
• Figure 1 illustrates interconnection wiring. Improper
connection will result in damage to the alarm, failure
to operate, or a shock hazard.
• Make certain alarms are wired to a continuous (nonswitched) power line.
NOTE: Use standard CSA listed household wire
(18 gauge or larger as required by local codes) available
at all electrical supply stores and most hardware stores.

• Smoke alarms are not to be used with detector
guards unless the combination (alarm and guard) has
been evaluated and found suitable for that purpose.
Wiring For AC Quick-Connect Harness:
CAUTION: Turn off the main power to the circuit
before wiring the alarm.
• For alarms that are used as single station, do not
connect the red wire to any t h i n g. Leave the red wire
insulating cap in place to make certain that the red wire
cannot contact any metal parts or the electrical box.
• When alarms are interconnected, all interconnected
units must be powered from a single circuit.
• A maximum of 24 Kidde safety products may be
interconnected in a multiple station arrangement:
Limit of 12 smoke alarms and/or 18 alarms total
(smoke, CO, Smoke/CO Combination, heat, etc.).
This Smoke/CO Combination alarm is counted as a
smoke alarm when determining the maximum
number of units on an interconnect line. With 18
alarms interconnected, it is still possible to
interconnect up to a total of 6 remote signaling

810-1692_RevD_119-133_MAN_ENG

10/7/03

4:41 PM

Installation
Mounting
CAUTION: This unit is sealed. The cover is not removable.
• Seven (7) years after initial power up, this unit will "chirp"
every 30 seconds to indicate that it is time to replace the
alarm. After seven years, the device may no longer detect
carbon monoxide accurately and should be replaced
immediately. To help identify the date to replace the unit,
a label has been affixed to the side of the alarm. Write
the "Replace by" date (7 years from power up) in
p e rmanent marker on the label. Remove the mounting
plate from the back of the alarm by holding the mounting
plate and twisting the alarm in the direction indicated by
the “OFF” arrow on the alarm cover.
• After selecting the proper Smoke/CO alarm location as
described on Pages 8-10, and wiring the AC QuickConnect wire harness as described in Wi ri n g, attach the
mounting plate to the electrical box. To ensure
aesthetic alignment of the alarm with the hallway, or
wall, the "A" line on the mounting plate must be
parallel with the hallway when ceiling mounted, or
horizontal when wall mounted.
• Pull the AC Quick-Connect wire harness through the
center hole in the mounting bracket and secure the
bracket, making sure that the mounting screws are
positioned in the small ends of the keyholes before
tightening.
FIGURE 2

ATTACHING THE AC QUICK-CONNECT WIRE HARNESS

• Plug the AC Quick-Connect wire harness into the back
of the alarm (see Figure 2), making sure that the locks on
the connector snap into place. Push the excess wire back
into the electrical box through the hole in the center of
the mounting plate.

Page 14

Installation
• Install the alarm on the mounting plate and rotate
the alarm in the direction of the “ON” arrow on the
cover until the alarm ratchets into place (this
ratcheting function allows for aesthetic alignment).
Note: The alarm will mount to the bracket in 4
positions (every 90 degrees).
• Turn on the AC power. The green AC Power On
Indicator should be lit when the alarm is operating
from AC power.
• For model KN-COSM-IBCA only, pull the Battery
Pull Tab (yellow tab protruding from unit)
completely out of unit. This will automatically
connect the battery.

Testing
CAUTION: Due to the loudness (85 decibels) of the
alarm, always stand an arms length away from the unit
when testing.
The Test/Reset/Hush® button has four purposes - it
tests the unit’s electronics, resets the CO alarm,
activates the Hush® feature, and activates the Peak
Level Memory feature.
After installation, test the unit’s electronics by pressing
the Test/Reset/Hush® button for five seconds. A series
of beeps will sound, followed by the message,
"Fire! Feu!" then another series of beeps and the
message, "Carbon Monoxide! Monoxyde de carbone!"
followed by 4 additional short beeps.
The unit needs to be tested weekly! If at anytime it
does not perform as described, verify that the power is
connected correctly and that the battery is fresh. Clean
any dust or other buildup on the unit. If it still does
not operate properly, call the Consumer Hotline at
1-800-880-6788.

810-1692_RevD_119-133_MAN_ENG

10/7/03

4:41 PM

Operation

Interconnect Feature

The Hush® feature can be used repeatedly until the air
has been cleared of the condition causing the alarm.

IMPORTANT: This unit is only approved to
interconnect with the Kidde line of products. It is not
approved to interconnect with any other manufacturer's
products.
• When compatible smoke alarms (1235CA, 1275CA,
1285CA, PE120CA, PI2000CA) and heat alarms
(HD135F) are interconnected to this alarm, they will
only respond to a smoke related event.
• When mixing compatible models with battery
backup (1275CA, 1285CA, PE120CA, PI2000CA,
HD135F, KN-COSM-IBCA) with models without
battery backup (1235CA, KN-COSM-ICA), be advised
that the models without battery backup will not
respond during an AC power failure.
For more information about compatible interconnect
units and their functionality in an interconnect system,
visit our web site at: www.kidde.ca
Hush® Control Feature
The Hush® feature has the capability of temporarily
desensitizing the smoke alarm circuit for about
10 minutes. This feature is to be used only when a
known alarm condition, such as smoke from cooking,
activates the alarm. You can put the Smoke/CO Alarm
in Hush® mode by pushing the Test/Reset/Hush®
button. If the smoke is not too dense, the alarm will
silence immediately, verbally announce, "Hush® mode
on! Mode Hush® activé!", and the green LED will flash
every 2 seconds for approximately 10 minutes. This
indicates that the smoke alarm is in a temporarily
desensitized condition. The alarm will automatically
reset after approximately 10 minutes. When the unit
returns to normal operation after being in Hush®
mode, it will verbally announce, "Hush® mode
cancelled! Mode Hush® annulé!" and sound the alarm
if smoke is still present.

Page 16

While the unit is in Hush® mode, pushing the
Test/Reset/Hush® button on the alarm will also end the
Hush® period.
NOTE: Dense smoke will override the Hush® control
feature and sound a continuous alarm.
CAUTION: Before using the alarm Hush® feature,
identify the source of the smoke and be certain a safe
condition exists.

Reset Feature
If the the Smoke/CO Alarm is sounding a CO alarm,
pressing the Test/Reset/Hush® button will silence the
alarm. If the CO condition that caused the alert
continues, the alarm will reactivate. Reactivation times
depend on the amount of CO present (see Page 24).

Peak Level Memory
If the CO sensor has detected a CO level of 100 PPM
or higher since last reset, it will be recorded by the
Peak Level Memory function. To access the Peak Level
Memory, press the Test/Reset/Hush® button. If a
reading of 100 PPM or higher has been recorded, the
unit will announce, "Caution! Attention!" If you’ve
been away from home, this feature allows you to
check if there was a CO reading of 100 or higher
during your absence. Pushing the Test/Reset/Hush®
button resets the memory. The memory is also reset
when the unit loses power.

810-1692_RevD_119-133_MAN_ENG

10/7/03

4:41 PM

Operation

Page 18

Operation

LED Indicators

TAMPER RESIST FEATURE

Red LED
The Red LED flashes in conjunction with the alarm.
The red LED will flash during a smoke alarm, a CO
alarm, a Low Battery Mode “chirp” and a Unit Error
Mode “chirp.”

FIGURE 3A

FIGURE 3B

Location
of Posts

Green LED
The green LED will flash under the following
conditions:

In Standby Condition (powered by AC and battery
backup) the green LED will be constantly on indicating
that 120 V AC power is being delivered to the alarm. It
will breifly flicker every 30 seconds when a CO
reading is taken.
For model KN-COSM-IBCA only, in Standby Condition
(powered only by battery backup) the green LED will
flash every 5 seconds.
In Alarm Memory Condition the green LED will flash
every second signifying that the alarm has sensed a
smoke or CO hazard. It will continue to flash every
second until the Test/Reset/Hush® button is pressed to
reset the alarm. When interconnected alarms cease to
sound, this flashing green LED indicates the originating
alarm that triggered all the others in the circuit, thus
reducing the time spent troubleshooting.
While in Hush® Mode, the green LED will flash every 2
seconds.

Tamper Resist Feature
To make the Smoke/CO alarm somewhat tamper
resistant, a tamper resist feature has been provided.
Activate the tamper resist feature by breaking off the
four posts in the square holes in the mounting plate
(see Figure 3A). Rotate the alarm onto the mounting
plate until you hear the tamper resist tab snap into
place, locking the alarm.
Using the tamper resist feature will deter children and
others from removing the alarm. To remove the alarm,
press on the tamper resist tab, and rotate the alarm off
of the mounting plate (see Figure 3B).

810-1692_RevD_119-133_MAN_ENG

10/7/03

4:41 PM

Alarm Removal
If the tamper resist feature has been activated, refer to
tamper resist feature description on page 19 for
removal instructions.
Remove the alarm from the mounting plate by rotating
the alarm in the direction of the “OFF” arrow on the
cover. To disconnect the AC Quick-Connect wire
harness, squeeze the locking arms on the sides while
pulling the connector away from the bottom of the
alarm (see Page 14, Figure 2).

Page 20

Battery Replacement
(For model KN-COSM-IBCA only)
FIGURE 4

BATTERY REPLACEMENT

Battery
tab

Battery Replacement
For model KN-COSM-IBCA only.
If any form of battery failure is detected, the red LED
light will flash and the unit will “chirp” one time,
followed by the warning message, "Low Battery! Pile
faible!" This cycle will occur once every minute, and
will continue for at least 7 days.
If the red LED light flashes along with a “chirp” every
30 seconds, and is not followed by the voice message,
"Low Battery! Pile faible!" as described above, the unit
has malfunctioned. Call our toll free Consumer Hotline
at 1-800-880-6788 for instructions on how to return the
unit.
CAUTION: This unit is sealed. The cover is not
removable.
To replace the battery you must first remove the alarm
from the mounting plate by following the Alarm
Removal instructions above. After the alarm has been
removed, you can open the battery door and replace
the battery. Battery installation instructions are provided
on the inside of the battery door.
When installing the battery, press the battery reminder
tab down into the battery compartment and install the
battery (see Figure 4).

CAUTION! If the battery reminder tab is not held down
in the battery compartment by the battery, the battery
door will not close, the AC Quick-Connect wire harness
will not attach to the alarm, and the alarm will not
attach to the mounting plate.
After changing the battery, reconnect the alarm and
test by using the Test/Reset/Hush® button, and check
that the green LED is on.
Replace battery with one of the following approved
brands:
Duracell MN1604 or MX1604
Energizer 522
Ultralife U9VL-J
These batteries can be purchased at your local retailer.
WARNING! Use only the batteries specified. Use of
different batteries may have a detrimental effect on the
Smoke/CO alarm. A good safety measure is to replace
the battery at least once a year, or at the same time you
change your clocks for daylight saving time.
Constant exposure to high or low humidity, or
temperature may reduce battery life.

810-1692_RevD_119-133_MAN_ENG

10/7/03

4:41 PM

Page 22

Maintenance

Carbon Monoxide Safety

To keep this Smoke/CO Alarm in peak condition:

General CO Information

• Verify the unit's alarm and LED lights operation by
pushing the Test/Reset/Hush® button once a week.

Carbon monoxide (CO) is a colorless, odorless, and
tasteless poison gas that can be fatal when inhaled. CO
inhibits the blood’s capacity to carry oxygen.

• Remove the unit from mounting plate and vacuum
the alarm cover and vents with a soft brush
attachment at least once a year to remove dust and
dirt. Reinstall immediately after cleaning and then
test using the Test/Reset/Hush® button.

Symptoms of CO Poisoning

• Never use detergents or other solvents to clean the
unit.

The following symptoms are related to carbon
monoxide poisoning and should be discussed with ALL
members of the household:

• Avoid spraying air fresheners, hair spray, or other
aerosols near the Smoke/CO Alarm.

Mild Exposure: Headaches, running nose, sore eyes,
often described as "flu"-like symptoms.

Do not paint the unit. Paint will seal the vents and
interfere with the sensor’s ability to detect smoke and
CO. Never attempt to disassemble the unit or clean
inside. This action will void your warranty.

Medium Exposure: Dizziness, drowsiness, vomiting.

Move the Smoke/CO Alarm to another location prior to
performing any of the following:
• Staining or stripping wood floors or furniture
• Painting or wall-papering
• Using adhesives
Storing the unit in a plastic bag during any of the
above projects will protect the sensors from damage.
WARNING: Reinstall the Smoke/CO Alarm as soon as
possible to assure continuous protection.

Extreme Exposure: Unconsciousness, brain damage,
death.
The above levels of exposure relate to healthy adults.
Levels differ for those at high risk. Exposure to high
levels of carbon monoxide can be fatal or cause
permanent damage and disabilities. Many cases of
reported carbon monoxide poisoning indicate that
while victims are aware they are not well, they become
so disoriented they are unable to save themselves by
either exiting the building, or calling for assistance.
Also, young children and household pets may be the
first affected. Familiarization with the effects of each
level is important.

When household cleaning supplies or similar
contaminants are used, the area must be well
ventilated. The following substances can affect the CO
sensor and may cause false readings and damage to
the sensor: Methane, propane, iso-butane, isopropanol, ethyl acetate, hydrogen sulfide, sulfide
dioxides, alcohol based products, paints, thinner,
solvents, adhesives, hair spray, after shave, perfume,
and some cleaning agents.

810-1692_RevD_119-133_MAN_ENG

10/7/03

4:41 PM

Page 24

Carbon Monoxide Safety

Initial carbon monoxide poisoning symptoms are
similar to the flu with no fever and can include
dizziness, severe headaches, nausea, vomiting and
disorientation. Everyone is susceptible, but experts
agree that unborn babies, pregnant women, senior
citizens and people with heart or respiratory problems
are especially vulnerable. If symptoms of carbon
monoxide poisoning are experienced, seek medical
attention immediately. CO poisoning can be
determined by a carboxyhemoglobin test.

Possible Sources of CO

CO Sensor Response Times

• Blocked chimneys or flues, back drafts and changes
in air pre s s u re, corroded or disconnected vent pipes,
loose or cracked furnace exchangers.

The CO sensor meets the alarm response time
requirements as follows:

CO can be produced when burning any fossil fuel, such
as gasoline, propane, natural gas, oil and wood. It can
be produced by any fuel-burning appliance that is
malfunctioning, improperly installed, or not ventilated
c o r rectly, such as:
• Fu rnaces, gas ranges/stoves, gas clothes dryers, water
heaters, portable fuel burning space heaters,
f i replaces, wood-burning stoves and certain
swimming pool heaters.

At 70 PPM, the unit must alarm within 60-240 minutes.

• Vehicles and other combustion engines running in an
open or closed garage, attached or near a home.

At 150 PPM, the unit must alarm within 10-50 minutes.

• C h a rcoal/gas grills and hibachis in an enclosed are a .

At 400 PPM, the unit must alarm within 4-15 minutes.
NOTE: This carbon monoxide alarm is designed to
detect carbon monoxide gas from ANY source of
combustion. It is NOT designed to detect any other
gasses.
Fire departments, most utility companies and HVAC
contractors will perform CO inspections. Some may
charge for this service. It’s advisable to inquire about
any applicable fees prior to having the service
performed. Kidde will not pay for, or reimburse, the
owner or user of this product, for any repair or
dispatch calls related to the alarm sounding.

810-1692_RevD_119-133_MAN_ENG

10/7/03

4:41 PM

Carbon Monoxide Safety
The fo l l owing conditions can result in transient CO
situations:
Excessive spillage or reverse venting of fuel-burning
appliances caused by:
• outdoor ambient conditions, such as wind direction
and/or velocity, including high gusts of wind, and
insufficient draft in the vent pipes;
• negative pressure differential resulting from the use
of exhaust fans;
• simultaneous operation of several fuel-burning
appliances competing for limited internal air;
• loose vent pipe connections from fuel-fired
appliances;
• obstructions, or unconventional vent pipe designs
that can amplify the above situations;
• poorly designed or maintained chimneys and/or
vents;
Extended operation of unvented fuel-burning devices
(range, oven, fireplace, etc.);
Temperature inversions that can trap exhaust gasses
near the ground; and a
Car idling in an open or closed attached garage, or
near a home.

Page 26

Carbon Monoxide Safety
Carbon Monoxide Alarm Procedure

WARNING: Actuation of the CO Alarm
indicates the presence of Carbon Monoxide
(CO) which can KILL YOU.
If alarm signal sounds 4 quick beeps, 5 seconds off:
1) Immediately move to fresh air - outdoors or by an
open door or window. Check that all persons are
accounted for. Do not re-enter the premises or
move away from the open door/window until
emergency services responders have arrived, the
premises have been aired out, and your alarm
remains in its normal operating condition.
2) Call your emergency local service
(fire deptartment or 911).
PHONE NUMBER

Never restart the source of a CO problem until it has
been corrected. NEVER IGNORE THE SOUND OF THE
ALARM!

Every year, have the heating system, vents, chimney
and flue inspected and cleaned by a qualified
technician. Always install appliances according to
manufacturer’s instructions and adhere to local building
codes. Most appliances should be installed by
professionals and inspected after installation. Regularly
examine vents and chimneys for improper connections,
visible rust, or stains, and check for cracks in furnace
heat exchangers. Verify that the color of flame on pilot
lights and burners is blue. A yellow or orange flame is
a sign that the fuel is not burning completely. Teach
all household members what the alarm sounds like and
how to respond in an emergency.

810-1692_RevD_119-133_MAN_ENG

10/7/03

4:41 PM

Page 28

Fire Safety

Escape Plan

• Go to a predetermined meeting place. When two
people have arrived, one should leave to call 911
from a neighbor’s home, and the other should stay
to perform a head count.
• Do not re-enter until fire officials say that it is safe to do so.
• There are situations where a smoke alarm may not
be effective to protect against fire as stated in the
NFPA Standard 72. For instance:
- smoking in bed;
- leaving children unsupervised;
- cleaning with flammable liquids, such as gasoline.

Familiarize everyone with the sound of the smoke alarm
and train them to leave the home when they hear it.
Practice a fire drill at least every six months, including fire
drills at night. Ensure that small children hear the alarm
and wake when it sounds. They must wake up in order
to execute the escape plan. Practice allows all occupants
to test your plan before an emergency. You may not be
able to reach your children. It is important they know
what to do. Know two ways out of every room (door &
window) and identify a meeting place outside the home
where everyone will gather once they have exited the
residence. When two people have reached the meeting
place, one should leave to call 911 while the second
person stays to account for additional family members.
Smoke Alarm Procedure
Smoke alarms are designed to minimize false alarms.
Cigarette smoke will not normally set off the alarm,
unless it’s blown directly into the alarm. Combustion
particles from spills or broiling may set off the alarm if
located too close to the cooking area. If the alarm
sounds, check for fires first. If a fire is discovered
follow these steps. Become thoroughly familiar with
these steps, and review them with all family members.

Fire Prevention
Never smoke in bed, or leave cooking food
unattended. Teach children never to play with
matches or lighters! Train everyone in the home to
recognize the alarm pattern, voice message warning
and to leave the home using their escape plan when
it’s heard. Be prepared to stop, drop and roll if clothes
catch on fire, and to crawl low under smoke. Install
and maintain fire extinguishers on every level of the
home and in the kitchen, basement and garage. Know
how to use a fire extinguisher prior to an emergency.
Second level and higher occupied rooms with
windows, should have an escape ladder.

• Alert small children in the home.
• Leave immediately using one of your planned
escape routes (see above).
• Before opening inside doors look for smoke seeping
through the edges. Feel with the back of your hand
- if the door is hot use your second exit. If you feel
it’s safe, open the door very slowly and be prepared
to close it immediately if smoke and heat rush in.
• If the escape route requires going through smoke,
crawl low under the smoke where the air is clearer.

810-1692_RevD_119-133_MAN_ENG

10/7/03

4:41 PM

Page 30

Fire Safety

Warranty

Additional Recommendations

5 Year Limited Warranty

Required number of smoke alarms: Smoke alarms
should be installed outside of each separate sleeping
area in the immediate vicinity of the bedrooms and on
each additional story of the family living unit (home),
including basements.

Kidde warrants that the enclosed alarm (but not the
battery) will be free from defects in material and
workmanship or design under normal use and service
for a period of five years from the date of purchase.
The obligation of Kidde under this warranty is limited
to repairing or replacing the alarm or any part w h i c h
we find to be defective in material, workmanship or
design, free of charge, upon sending the alarm with
proof of date of purchase, postage and return postage
prepaid, to: Kidde, Customer Service Department, 130
Esna Park Drive, Markham ON L3R 1E3.

Some jurisdictions require that in new construction, a
smoke alarm be installed in each sleeping room.
Check with local officials for specific regulations
concerning your situation.
The required number of smoke alarms (protected areas
mentioned above) might not be reliable enough to
provide early warning for unprotected areas that are
separated by a door. For this reason, it is
recommended that the householder consider the use of
additional smoke alarms for those unprotected areas,
for increased protection. Additional areas include the
basement, bedrooms, dining room, furnace room,
utility room, and hallways not protected by the
required number of smoke alarms.
The installation of smoke alarms in kitchens, attics
(finished or unfinished), or garages is not normally
recommended, as these locations occasionally
experience conditions that can result in improper
operation.

This warranty shall not apply to the alarm if it has
been damaged, modified, abused or altered after the
date of purchase or if it fails to operate due to
improper maintenance or inadequate AC or DC power.
Any implied warranties arising out of this sale,
including but not limited to the implied warranties of
description,merchantability and fitness for a particular
purpose, are limited in duration to the above warranty
period. In no event shall Kidde be liable for loss of
use of this product or for any indirect, special,
incidental or consequential damages, or costs, or
expenses incurred by the consumer or any other user
of this product, whether due to a breach of contract,
negligence, strict liability in tort or otherwise. Kidde
shall have no liability for any personal injury, property
damage or any special, incidental, contingent or
consequential damage of any kind resulting from gas
leakage, fire or explosion.
Since some provinces do not allow limitations of the
duration of an implied warranty or do not allow the
exclusion or limitation of incidental or consequential
damages, the above limitations or exclusions may not
apply to you. While this warranty gives you specific
legal rights, you may also have other rights which vary
from province to province.

810-1692_RevD_119-133_MAN_ENG

10/7/03

4:41 PM

Warranty

Page 32

Notes

Also, Kidde makes no warranty, express or implied,
written or oral, including that of
merchantability or fitness for any particular purpose,
with respect to the battery.
The above warranty may not be altered except in
writing signed by both parties hereto.
This Kidde Combination Smoke & CO Alarm is not a
substitute for property, fire, disability, life or other
insurance of any kind. Appropriate insurance coverage
is your responsibility. Consult your insurance agent.
Removal of the front cover will void the warranty.
NOTE: This alarm is not intended to alert hearing
impaired individuals.
During the specified warranty period Kidde will repair or
replace, at its discretion any defective Kidde Combination
Smoke & CO Alarms that are returned in a postage paid
package to the following address: Kidde, Customer Service
Department, 130 Esna Park Drive, Markham ON L3R 1E3.
Please include your name, address and phone number
along with a brief description of what is wrong with the
unit. For further assistance please call our toll free
Consumer Hotline at 1-800-880-6788. Damage from neglect,
abuse or failure to adhere to any of the enclosed
instructions will result in termination of the warranty, and
the unit will not be replaced or re p a i red.
The model numbers are:
KN-COSM-IBCA (with battery backup)
KN-COSM-ICA (without battery backup)
This manual and the products described herein are
copyrighted, with all rights reserved. Under these copyright
laws, no part of this manual may be copied for use without
the written consent of Kidde. If you require further
information please contact out Consumer Hotline at:
1-800-880-6788, or write us at: Kidde, Customer Service
Department, 130 Esna Park Drive, Markham ON L3R 1E3.
Our internet address is www.kidde.ca

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Create Date                     : 2003:10:07 20:41:56Z
Creator                         : QuarkXPress
Modify Date                     : 2014:12:07 15:06:32+08:00
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03
Creator Tool                    : QuarkXPress
Metadata Date                   : 2014:12:07 15:06:32+08:00
Producer                        : Mac OS X 10.2.8 Quartz PDFContext
Format                          : application/pdf
Document ID                     : uuid:41a43288-8e86-11da-8343-000393dac392
Instance ID                     : uuid:c1ef3f1b-3963-a848-b3d1-ea217fd12356
Page Layout                     : SinglePage
Page Count                      : 18

EXIF Metadata provided by EXIF.tools

Kidde Kn Cosm Ica Users Manual

Navigation menu

Versions of this User Manual:

Views

Navigation