Kiddesigns 210A1 FRS 2-Way Radios (Walkie Talkie) User Manual CR 210 IB 1023

Download:
Mirror Download [FCC.gov]
Document ID	2985584
Application ID	VU04kJjVnaKuUiB7j010+g==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	59.61kB (745084 bits)
Date Submitted	2016-05-10 00:00:00
Date Available	2016-05-10 00:00:00
Creation Date	2013-10-28 12:09:20
Producing Software	Adobe PDF library 10.01
Document Lastmod	2016-05-09 10:40:23
Document Title	CR-210 IB 1023
Document Creator	Adobe Illustrator CC (Macintosh)

CR-210 IB_back Printing color: Black Oct. 23, 13.
Getting Started
Installing the Batteries
Note: Batteries should always be installed by an adult.
 Use a Phillips screwdriver to open the battery
compartment door located on the back of the unit.
 Insert 4 AAA (R03) batteries into each Walkie
Talkie with + and - terminals as indicated in the
compartment.
 Replace the compartment door and tighten the
screw with a Phillips screwdriver. Do not
over-tighten the screw.
For the Best Possible Performance
• We recommend the use of alkaline batteries for longer life.
• Do not mix old and new batteries.
• Do not mix alkaline, standard (carbon-zinc) or
rechargeable (nickel-cadmium) batteries.
• Batteries are to be inserted with correct polarity.
• Remove exhausted batteries from the unit.
• Do not attempt to recharge non-rechargeable
batteries.
• Remove the rechargeable batteries from the unit
before charging.
• The supply terminals are not to be short-circuited.
• Batteries should be removed if the item will not be
used for an extended period of time, such as a month
or longer, to prevent battery leakage or damage.
• Rechargeable batteries should only be charged under
adult supervision.
• Only batteries of the same or equivalent type as
recommended are to be used
Troubleshooting
• Both Walkie Talkies must be turned on and have
their antennas pointing upwards in order to send
and receive messages (speak and listen).
• Messages cannot be received while the Talk
Button is being pressed. Release the Talk Button
to listen.
• Messages can be heard through the Speaker.
If one or both of the Walkie Talkies do not work, this
may indicate that the batteries are weak. Insert 4 new
AAA (R03) batteries into each unit. If the signal range
of the Walkie Talkies decreases notably, this may again
be an indication that the batteries are weak. Insert 4
new AAA (R03) batteries into each unit.
Please keep in mind that this product does not transmit
well through obstacles such as trees, buildings, and
metal structures.
If there is a sizable increase in static, it may be due to
the proximity of electric motors, fluorescent lights, power
lines, or other signal-disrupting objects. You may have
to change your location.
If problems persist, DO NOT ATTEMPT TO REPAIR
THE UNIT. See the Warranty for factory services.
Playing Walkie Talkie Games
Power LED
Walkie Talkies can be used for all kinds of fun games
and activities. Here are two suggestions:
Hide and Seek
Just like regular Hide and Seek, but with a twist: the
“Hider” can send clues to the “Seeker” using the Walkie
Talkies.
Mystery Sounds
Can you recognize the mystery sound? One kid sends
a sound over the Walkie Talkies, while another tries to
guess what the sound is. Examples can include an
animal, song, TV show, or anything else!
Talk Button
Maintenance
Power/Volume Knob
Speaker
It is important to keep the Walkie Talkies as dry and
clean as possible. You may clean the cabinet with a
cloth or sponge moistened with mild soap and water.
Do not attempt to use strong cleansers or solvents, as
they may cause damage.
Turning Power On/Off
Questions or Comments
• Turn Power/Volume Knob right (clockwise) to turn
on the Walkie Talkies. The Power LED will light to
indicate unit is ON.
• Both Walkie Talkies must be turned on in order to
send and receive messages.
• Turn Power/Volume Knob left (counter-clockwise)
to shut off the Walkie Talkies.
• For questions or comments regarding this or other
KIDdesigns products, please call our toll-free
number: 1-888-TOP-TOYS
Also visit our website: www.kiddesigns.com
If problems persist, please do not attempt to repair
unit; see warranty for factory service.
Speaking
Press and hold the Talk Button while speaking into
the Microphone. Release Talk Button to listen. Adjust
volume using Power/Volume Knob.
You Should Know
For clear transmission, keep the antenna pointing
upwards and the microphone approximately two
inches from your mouth.
Listening
Microphone
FCC Information
This device complies with Part 15 of the FCC rules.
Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this
device must accept any interference received, including
interference that may cause undesired operation.
NOTE: This equipment has been tested and found to
comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause
harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician
for help.
WARNING: Changes or modifications to this unit not
expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
CAN ICES-3 (B)/NMB-3(B)
CR-210 IB_front Printing color: Black Oct. 23, 13.
Replacement of any transmitter component (crystal,
semiconductor, etc.) not authorized by the IC/FCC
equipment authorization for this radio could violate
IC/FCC rules.
Portable Radio Operation and RF Exposure
Antenna Care
Use only the supplied or an approved replacement
antenna.
Unauthorized antennas, modifications, or attachments
could damage the radio and may violate FCC/IC
regulations.
Limited One-Year Warranty
KIDdesigns, a division of SDI Technologies Inc. (hereafter referred to as
SDI), warrants this product to be free from defects in workmanship and
materials, under normal use and conditions, for a period of one (1) year
from the date of original purchase.
Should this product fail to function in a satisfactory manner, it is best to
first return it to the store where it was originally purchased. Should this fail
to resolve the matter and service still be required by reason of any defect
or malfunction during the warranty period, SDI will repair or, at its
discretion, replace this product without charge. This decision is subject to
verification of the defect or malfunction upon delivery of this product to
the Factory Service Center authorized by SDI Customer Service. The
product must include proof of purchase, including date of purchase. An
out-of-warranty fee for service will be charged for units that are received
without proof of purchase.
Before returning this product for service, please first replace the batteries
(if applicable) with fresh ones, as exhausted or defective batteries are the
most common cause of problems encountered.
If service is still required:
1. Call SDI Customer Service at 1-888-TOP-TOYS (1-888-867-8697) for
Return Authorization and for the address of the Factory Service Center.
2. Remove the batteries (if applicable) and pack the unit in a well padded,
heavy corrugated box. SDI is not responsible for damage that occurs
during shipping to the Factory Service Center.
3. Enclose a photocopy of your sales receipt, credit card statement, or
other proof of the date of purchase, if within the warranty period. Also
include your name and address information, a brief description for why
the unit is being returned, and the return authorization number. No unit
can be processed without a return authorization number.
4. Write the return authorization number on the side of the shipping
package and send the unit prepaid and insured to the Factory Service
Center address authorized by SDI Customer Service.
Disclaimer of Warranty
NOTE: This warranty is valid only if the product is used for the purpose for
which it was designed. It does not cover (i) products which have been
damaged by negligence or willful actions, misuse or accident, or which
have been modified or repaired by unauthorized persons; (ii) cracked or
broken cabinets, or units damaged by excessive heat; (iii) damage to
digital media players, CD’s or tape cassettes (if applicable); (iv) the cost
of shipping this product to the Factory Service Center and its return to the
owner.
This warranty is valid only in the United States of America and does not
extend to owners of the product other than to the original purchaser. In no
event will SDI or any of its affiliates, contractors, resellers, their officers,
directors,
shareholders, members or agents be liable to you or any third party for
any consequential or incidental damages, any lost profits, actual,
exemplary or punitive damages. (Some states do not allow limitations on
implied warranties or exclusion of consequential damages, so these
restrictions may not apply to you.) This warranty gives you specific legal
rights, and you may also have other rights which vary from state to state.
Your acknowledgement and agreement to fully and completely abide by
the above mentioned disclaimer of warranty is contractually binding to
you upon your transfer of currency (money order, cashier's check, or
credit card) for purchase of your SDI product.
© 2013 SDI Technologies, Inc. All Rights Reserved
Questions? Visit www.eKids.com
or call 1-888-TOP-TOYS
© Disney/Pixar
Visit Disney/car.com
Distributed by KIDdesigns, Inc. Rahway, NJ 07065-5024
eKids is a wholly owned subsidiary of KidDesigns, Inc,
1299 Main Street Rahway NJ 07065
Printed in China
CR210-102313-B
Model CR-210
Pit Stop
Walkie Talkies
Important Message to Customers
Thank you for purchasing one of Disney/Pixar’s many top-quality electronic products. We would appreciate it if you take
a few moments to read through these instructions. This will help you explain to the child the safe and proper way to use
this toy, and to help give it the long-lasting life that Disney/Pixar products are designed for.
FRS FREQUENCY CHART (MHz)
CH. No.
CH. Freq.
CH. No.
CH. Freq.
CH. No.
CH. Freq.
462.5625
462.6375
462.7125
462.5875
462.6625
---
---
462.6125
462.6875
---
---
FCC Warning
To ensure that your expose to RF electromagnetic
energy is Within the FCC allowable limits for
occupational use, alwaysAdhere to the following
guidelines:
z DO NOT operate the radio without a proper antenna attached, as this may damaged the radio
And may also cause you to exceed FCC RF exposure limits, A proper antenna is the antenna
Supplied with this radio by the manufacturer or antenna specifically authorized by the
manufacturer for use with this radio.
z DO NOT transmits for more than 50% of total radio use time (“50% duty cycle). Transmitting
more than 50% of the time can cause FCC RF exposure compliance requirements to be
exceeded. The radio is transmitting when the “TX indicator” lights red. You can cause the
radio to transmit by pressing the “PTT” switch.
z ALWAYS kepp the antenna at least 2.5cm (1 inch) away from the body when transmitting and
Only use the belt-clip which is listed in instructions when attaching the radio to your belt, etc.,
to ensure FCC RF exposure compliance requirements are not exceeded.
The information listed above provides the user with the information needed to make him or her
aware of RF exposure, and what to do to as-sure that this radio operates with the FCC RF
exposure limits of this radio.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation
NOTE 1: This equipment has been tested and found to comply with the part 95 of the FCC rules.
These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and,
if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications not expressly approved by the manufacturer could void the user’s
authority to operate the equipment.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
XMP Toolkit                     : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
Format                          : application/pdf
Title                           : CR-210 IB 1023
Creator Tool                    : Adobe Illustrator CC (Macintosh)
Create Date                     : 2013:10:28 12:09:20+08:00
Modify Date                     : 2016:05:09 10:40:23+08:00
Metadata Date                   : 2016:05:09 10:40:23+08:00
Thumbnail Width                 : 256
Thumbnail Height                : 72
Thumbnail Format                : JPEG
Thumbnail Image                 : (Binary data 9609 bytes, use -b option to extract)
Document ID                     : xmp.did:81e3b325-e368-41c4-a7a6-8273e2f77047
Instance ID                     : uuid:50336078-c2c4-4c0b-aee1-6dc3cee64f45
Original Document ID            : uuid:159BC99AC15D11DEA5E0A6E7895E1B6A
Rendition Class                 : proof:pdf
Derived From Instance ID        : xmp.iid:b3211675-e413-4e54-a3b8-9ad29cceb0fa
Derived From Document ID        : xmp.did:b3211675-e413-4e54-a3b8-9ad29cceb0fa
Derived From Original Document ID: uuid:159BC99AC15D11DEA5E0A6E7895E1B6A
Derived From Rendition Class    : proof:pdf
History Action                  : saved, saved
History Instance ID             : xmp.iid:38EEA2CC352068118083FC9B34ECAB17, xmp.iid:81e3b325-e368-41c4-a7a6-8273e2f77047
History When                    : 2010:12:02 17:24:55+08:00, 2013:10:28 12:09:15+08:00
History Software Agent          : Adobe Illustrator CS5, Adobe Illustrator CC (Macintosh)
History Changed                 : /, /
Manifest Link Form              : EmbedByReference, EmbedByReference, EmbedByReference
Manifest Reference File Path    : /Volumes/dannyTSANG 500G/Model in process/Brands/KD/CR models/CR-210/IB/CR logo_grey.psd, /Users/dannytsang/Desktop/2.jpg, /Users/dannytsang/Desktop/1.jpg
N Pages                         : 1
Has Visible Transparency        : True
Has Visible Overprint           : True
Max Page Size W                 : 420.000218
Max Page Size H                 : 296.999970
Max Page Size Unit              : Millimeters
Font Name                       : ArialMT, Arial-ItalicMT, Arial-BoldMT, EuropeanPi-One, GoodTimesHv-Italic, HelveticaNeue-Bold
Font Family                     : Arial, Arial, Arial, European Pi, Good Times, Helvetica Neue
Font Face                       : Regular, Italic, Bold, 1, Heavy Italic, 75 Bold
Font Type                       : Open Type, Open Type, Open Type, Type 1, Open Type, Type 1
Font Version                    : Version 3.05, Version 3.05, Version 3.05, 001.000, OTF 4.000;PS 001.001;Core 1.0.29, 001.100
Font Composite                  : False, False, False, False, False, False
Font File Name                  : Arial, Arial, Arial, EuropPiOne; European Pi Screen Fonts, good times hv it.otf, HelveNeuBol; Helvetica Neue SFAD
Plate Names                     : Cyan, Magenta, Yellow, Black
Swatch Groups Group Name        : Default Swatch Group
Swatch Groups Group Type        : 0
Swatch Groups Colorants Swatch Name: PANTONE 165 C
Swatch Groups Colorants Type    : SPOT
Swatch Groups Colorants Tint    : 100.000000
Swatch Groups Colorants Mode    : CMYK
Swatch Groups Colorants Cyan    : 0.000000
Swatch Groups Colorants Magenta : 58.999997
Swatch Groups Colorants Yellow  : 95.999998
Swatch Groups Colorants Black   : 0.000000
Producer                        : Adobe PDF library 10.01
Page Count                      : 4
Creator                         : Adobe Illustrator CC (Macintosh)

EXIF Metadata provided by EXIF.tools