Kitchenaid KESC308LSS0 User Manual IN RANGE ELECTRIC Manuals And Guides L0503056
KITCHENAID Free Standing, Electric Manual L0503056 KITCHENAID Free Standing, Electric Owner's Manual, KITCHENAID Free Standing, Electric installation guides
User Manual: Kitchenaid KESC308LSS0 KESC308LSS0 KITCHENAID -IN RANGE - ELECTRIC - Manuals and Guides View the owners manual for your KITCHENAID -IN RANGE - ELECTRIC #KESC308LSS0. Home:Kitchen Appliance Parts:Kitchenaid Parts:Kitchenaid -IN RANGE - ELECTRIC Manual
Open the PDF directly: View PDF 
.
Page Count: 12
| Download | |
| Open PDF In Browser | View PDF |
® HOME APPLIANCES II " 9758646 " e Freestanding Range Quick Reference Table of Contents: Pages Before you start Product dimensions Tip Over A child or adult be killed. Connect anti-tip range foot. Cabinet dimensions requirements Hazard can tip the range bracket Reconnect the anti-tip range is moved. EUectdcaU requirements and %-_ to rear bracket, [] Check operation Ufrange does not operate if the Failure to follow these instructions result in death or serious burns to children and aduIts. HnstaHationsteps If you need assistance'service can [] Moving the range www.Mtchenaid.com Read and save these instructions. Write iMPORTANT: installer: Instructions Leave HnstaHation with the homeowner. Homeowner: Instructions Read and for local down numbers Keep Installation for future reference, save these electrical instructions inspector's Both use. numbers model/serial on the oven storage Model Serial the before model are listed rating frame drawer and installing serial range. on the plate located behind the panel # # Part No. 9758646 Mobile Before you start... Your safety and the safety others are very important. of We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages. This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word 'DANGER" or 'WARNING." These words home installation The installation of this range must conform with the Manufactured Home Construction and Safety Standard,Title 24 CFR, Part 3280 [formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD (Part 280)] or, when such standard is not applicable, the Standard for Manufactured Home Installations, ANSI A225J/NFPA 501A *, or with local codes. When this range is installed in a mobile home, it must be secured to the floor during transit. Any method of securing the range is adequate as long as it conforms to the standards listed above. Four-wire power supply cord or cable must be used in a mobile home mean: installation.The appliance wiring will need to be revised. See "Four-wire electrical connection" section. You can be killed or seriously injured if you don't immediatebL follow instructions. The floor anti-tip bracket must be installed.To install You can be kitied if you don't follow or seriously instructions. injured All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed. IMPORTANT: Observe all governing codes and ordinances. Failure to meet codes and ordinances could lead to fire or electrical shock. Proper installation is your responsibility. A qualified technician must install this range. Make sure you have everything necessary for correct installation. It is the installer's responsibility to comply with installation clearances specified on the model/serial rating plate.The model/serial rating plate is located on the oven frame behind the storage drawer panel. Check location where range will be installed.The range should be located convenient use in kitchen. for To eliminate the risk of burns or fire by reaching over heated surface units, cabinet storage space located above the surface units should be avoided. If cabinet storage is to be provided, the risk can be reduced by installing a range hood that projects horizontally a minimum of 5 inches beyond the bottom of the cabinets. All openings in the wall ranges is to be installed or floor where must be sealed. Cabinet opening dimensions shown must be used. Given are minimum clearances. that are dimensions Grounded electrical outlet is required. See "Electrical requirements" section. the anti-tip bracket shipped with the range, see Page 5 and the anti-tip bracket template. Copies of the standards listed may be obtained from: National Fire Protection Association One Batterymarch Park Quincy, Massachusetts, 02269 Tools needed: Follow all factory safety instructions included with your tools. • level fiat-blade screwdriver 3/8" drive ratchet 3/8" and 5/16" nut drivers hand or electric channel measuring wood drill lock pliers tape or ruler floors: 1/8" drill bit concrete/ceramic floors: 3/16" carbide-tipped masonry (Hammer drill bit may be needed for anchors,) Parts supplied: Not shown: literature pack 2 plastic anchors 2 screws (#10 x I-1/2") floor-mounted anti-tip bracket Brackets must be securely mounted to sub-floor, Thickness of flooring may require longer screws to anchor bracket to sub-floor, Longer screws are available from your local hardware store. Product dimensions Freestanding When installed in a 24" (61.0 crn) base cabinet with 25" (63.5 crn} Range 30" (76.2 cm) j/_ coogreen_ ground wire Use this method for new installations, mobile homes, recreational vehicles whenever four-wire installation is required. I screws+ tightened nuts+ _;_?_ _ 1 lineI 4. electdea[ any other 2+ terminal See 11. Connect and lug (attached to center of terminal block). See 3+ the 2) to the other outer two wires aluminum dines 1 lugs+ 12+ Securely tighten the set screws. For 8 gauge copper wire, tighten to 25 in/ibs of torque, and for 6 gauge aluminum wire, tighten to 35 in/Ibs of torque to make a proper electrical connection+ See Figure 3+ 13+ Tighten the connector+ locking 14. Replace terminal the ring of the conduit block cover. Operating position Move chose to cabinet range m Make Remove cardboard • Look for the anti-tip attached to floor. or hardboard from under range. Carefully move range into final position. I sure the anti-tip bracket bracket securely is installed: opening. M Pull drawer open to first • Slide range back so rear is under anti-tip bracket. range Place rack in oven. Place level on rack, first side to side; then front to back foot stop position. Lift front of drawer to clear white wheels in drawer guides. Remove drawer and set it aside on a protected surface. anti-tip bracket range R If installing the range foot in a mobile home, you must secure the range to the floor. Any method of securing the range is adequate as long as it conforms to the standards in the "Mobile home installation"section. If range is not level, pull range forward until rear leveling leg is removed from the anti-tip bracket. Use 3/8" drive ratchet and channel lock pliers to adjust leveling legs up or down until range is level. Push range back into position. Check that rear leveling leg is engaged in anti-tip bracket. NOTE: Oven satisfactory must baking m Replace lower be level the storage panel. [] Reconnect for conditions. power. drawer or Check operation 7[] Check the operation cooktop eiements: Push in and turn each surface unit controi knob to "Hi" position. Check the operation of the cooktop eiements and indicator lights. M Check the The bottom element should glow red and the indicator light should be on.The upper element should become hot but not glow red. As the oven temperature rises, the temperature in the display will increase in 5°F increments until the oven of the OFF o reaches Press the set temperature. "CANCEL/OFF" pad. _ % operation MED of the oven element: Press the "BAKE" pad. "350°F " wiii appear in the temperature display. Press the "START" pad, "LO" will appear in the display; then "170°F " (when oven reaches 170°F). [] Check the operation of the broil element. Close the oven door. Press the "BROIL' pad, "500°F '' wiii appear in the temperature display. Press the "START" pad. You have just finished installing your new range.To get the most efficient use from your range, read your Use & Care Guide. Keep Installation Instructions and Guide cJose to range for easy reference. The instructions wilt make installing the range in another home as easy as the first installation. Look through the oven window.The top element should glow red. Press the "CANCEL/OFF" pad. qC3 83{383 SET,START CLOCK NOTE: Control panels may vary. 1 /f range does not /f you need assistance: If you need service: operate: if you have questions cleaning or maintaining in the event that your KitchenAid appliance should need service, call the deabr from whom you purchased the appliance or a KitchenAid-authodzed service company. A KitchenAidauthorized service company is listed in theYellow Pages of your telephone directory under "Appliances - Household - MajorService & Repaid'You can also obtain the service company's name and number by dialing, free within the continental United States, the KitchenAid Customer Interaction Center telephone number, 1-800-422-1230. A special operator will tell you the name of your nearest KitchenAid-authorized service [_ Check that the circuit tripped or the house [_ Check plugged [_ that the breaker is not fuse blown. power into the supply cord is [_ Refer to [_ The KitchenAid Customer interaction Center wiii answer any questions about operating or maintaining your range not covered in the Installation Instructions.The KitchenAid outlet. See Use and Care Guide troubleshooting list, for Use and about operating, your range: Care Guide. Customer interaction Center is open 24 hours a day, 7 days a week. Just dial 1-800-422-1230 -the cail is free within the continental United States. When you call, you wiii need the range model number and serial number. Both numbers can be found on the model/serial rating located on the oven frame the door. plate behind company. Maintain the quality KitchenAid appliance KitchenAid-authorized built into your -- call a service company. Moving the range When moving range, slide range onto cardboard or hardboard to prevent damaging the floor covering, If removing the range is necessary cleaning or maintenance: Tip Over A child or adult be kiHed. Connect anti-tip range foot. Hazard can tip the bracket Reconnect the anti4ip range is moved. range and to rear bracket, or disconnect if the can _ "X._S'_'._ 1. Unplug 2. Slide range forward to complete cleaning or maintenance. 3. Make sure installed: the anti-tip • Look for the anti4ip attached to floor. anti-tip bracket power. bracket range foot is bracket securely • Slide range back so rear is under anti4ip bracket. Failure to follow these instructions resumt in death or serious burns to children and adults. 10 range for range foot 4. Check that range is level. 5. Plug in range or reconnect power. Notes 11 i :che HOME APPLIANCES Part No. 9758646 © 2004 KitchenAid ® RegisteredTrademark Printed in U.S.A. of KitchenAid. Prepared by KitchenAid, Benton Harbor, Michigan 49022 0!/2004
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : No Page Count : 12 Page Layout : SinglePage Page Mode : UseNone Producer : Goby Monitor Application version 3, 2, 1, 4 Create Date : Fri Apr 20 16:29:22 2007 Author : Title : Subject :EXIF Metadata provided by EXIF.tools