Klipsch KMC3 Portable Bluetooth Speaker system User Manual

Download:
Mirror Download [FCC.gov]
Document ID	1927192
Application ID	spdGlZGIzOjTQZXythQDfQ==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	94.02kB (1175191 bits)
Date Submitted	2013-03-28 00:00:00
Date Available	2013-03-29 00:00:00
Creation Date	2013-01-16 10:00:01
Producing Software	Adobe PDF Library 10.0.1
Document Lastmod	2013-03-25 14:10:56
Document Title	User Manual
Document Creator	Adobe InDesign CS6 (Macintosh)

Thank You
Thank you for your purchase of the Klipsch® Music Center KMC 3!
The KMC 3 combines legendary Klipsch technology with Bluetooth®
and aptX™ technology for truly hi-fidelity music playback from
your favorite music device. Its contemporary styling compliments
any décor and you can take it almost anywhere with both AC and
battery-power options.
AC Power
To operate on AC power plug AC adapter into back of the KMC 3
marked DC IN, then plug AC adaptor into a functioning wall socket.
On AC power, if no streaming or connected audio is detected for
one hour the KMC 3 will automatically go into standby mode.
Battery Power
To operate on battery power, install 8 D Cell (LR20) alkaline
batteries as shown. If batteries are installed, the KMC 3 operates
on battery power unless AC power is utilized. On battery power,
if no streaming or connected audio is detected for five minutes,
the KMC 3 will automatically power off.
REMOTE Control Functions
Illuminated Control Functions
POWER ON / OFF
1.
POWER ON / OFF - Tap to turn on. Hold to turn off. Solid
Red indicates Power On, flashes if batteries are weak
2.
BLUETOOTH
No Connection
Hold to Pair
Tap to Exit
Connected
Hold to
Disconnect
VOLUME DOWN
MUTE
VOLUME UP
TRACK REVERSE
(Bluetooth mode only)
PLAY / PAUSE
3.
VOLUME DOWN
(Bluetooth mode only)
4.
VOLUME LEVEL INDICATOR
TRACK FORWARD
5.
VOLUME UP
(Bluetooth mode only)
6.
SOURCE SELECT - Pressing + and – together toggles
between Bluetooth mode and AUX (3.5mm input) for playback
SOURCE / BLUETOOTH
(See Illuminated Control Functions #2)
Device does not play in Bluetooth mode or AUX input
• Make sure volume on device is up to maximum/KMC 3
volume is up at least half way and not MUTED
• If using AUX input, make sure connections are tight
• Touch + and – buttons together to select correct input
• If solid blue touch and hold + and – together to switch inputs
LIP
. K
SCH
The Bluetooth® word mark is a registered trademark owned by Bluetooth SIG, Inc. and any use of such mark by Klipsch Group, Inc. is under license.
, A
The “aptX™ software is copyright CSR plc or its group companies. All rights reserved. The aptX™ mark and the aptX logo are trade marks of CSR plc or
one of its group companies and may be registered in one or more jurisdictions.
Klipsch is a trademark of Klipsch Group, Inc., registered in the U.S. and other countries. All other trademarks are property of their respective owners.
Klipsch is a wholly-owned subsidiary of Voxx International Corporation. ©2012, Klipsch Group, Inc.
Care and Cleaning
Your KMC 3 music center has a durable finish that should only
require dry dusting or cleaning with a dry cloth. Avoid the use
of abrasive or solvent-based cleaners and harsh detergents.
Adhesive tape will clean up the rubber device area when it has
dust and particles on it. Do not rub hard. Window cleaner and a
paper towel will clean the surface well.
Device will not pair with Bluetooth mode
• Make sure KMC 3 is in pairing mode (∞ flashing blue)
• Make sure you are within 30 feet (9.1 m) of KMC 3 while
pairing; move closer/make sure you are in the same room
• Make sure your volume settings are correct
Pairing Bluetooth Devices
Touch the Bluetooth button on unit down until it begins to flash
(approximately 3 seconds). Do not touch any other buttons on
the KMC 3 or its remote during this process. While the Bluetooth
button flashes blue, activate the Bluetooth feature on your
music device or phone, setting it up to pair with “Klipsch KMC
3”. Once paired, the KMC 3 will automatically select Bluetooth
as the source. First, adjust the volume of the KMC 3 to the below
illustrated range for optimum performance. Then, while streaming
music from your device, adjust the device volume to desired level.
USB Charging
NOTE: The USB input is only for CHARGING most music players,
phones, and tablets. Using the USB connection end of the charging
cable for your device (not included), connect to the USB input
on rear of the KMC 3 to charge your device. You can charge your
device using either AC or battery power for the KMC 3.
NOTE: Using the USB input to charge your device while the KMC 3
is on battery power will reduce battery life. If batteries in the KMC
3 are too weak, the USB connection will not charge your device.
TROUBLESHOOTING
KMC 3 will not power on
• Make sure AC adapter is plugged tightly into DC input
• Make sure AC adapter is plugged into a live outlet
• If no AC connection make sure all 8 batteries are inserted
into battery compartment correctly
• Install fresh batteries if not plugged into DC input
Any device with a standard 3.5mm headphone output can be
connected to the AUX input (on back) with a mini-to-mini
connecting cable (included). Once connected, make sure volume
on KMC 3 is just above minimum, adjust volume on your device
to maximum and play music. Use SOURCE SELECT to switch to
AUX input if necessary. Adjust volume up to desired level.
The next time the KMC 3 is powered on it will automatically
search for the last paired Bluetooth device and, if available, will
automatically connect and go to Bluetooth as the source. If the
last paired Bluetooth device is not available or not playing it will
automatically choose the AUX (3.5mm input) as the source. The
KMC 3 can store up to 8 paired Bluetooth devices.
PA
Music Sources
Any paired Bluetooth device within a 30 foot (9.1 m) range of the
KMC 3 can wirelessly stream music.
ST
. 1
9 4 6
ENGLISH
Canada Statement
This device complies with Industry Canada RSS-210. Operation is subject to the following two
conditions: (1) this device may not cause interference, and(2) this device must accept any
interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio
RSS-210. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas
produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioé
lectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102
and compliance with RSS-102 RF exposure, users can obtain Canadian information on RF
exposure and compliance.
Le dispositif rencontre l'exemption des limites courantes d'évaluation dans la section 2.5 de
RSS 102 et la conformité à l'exposition de RSS-102 rf, utilisateurs peut obtenir l'information
canadienne sur l'exposition et la conformité de rf.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
—Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled
environment. This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter. This equipment should be installed and operated with a minimum
distance of 20 centimeters between the radiator and your body.
This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause
undesired operation.
Caution!
The manufacturer is not responsible for any radio or TV interference caused by unauthorized
modifications to this equipment. Such modifications could void the user authority to operate
the equipment.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
XMP Toolkit                     : 3.1-701
Create Date                     : 2013:01:16 10:00:01-05:00
Metadata Date                   : 2013:03:25 14:10:56+08:00
Modify Date                     : 2013:03:25 14:10:56+08:00
Creator Tool                    : Adobe InDesign CS6 (Macintosh)
Instance ID                     : uuid:c2c7c056-c3ce-4fdc-ae6e-8f2a0333078d
Original Document ID            : xmp.did:BFBB06B32A2068118A6DF9B7543F7449
Document ID                     : xmp.id:26528B4D09206811822A92402D5D460B
Rendition Class                 : proof:pdf
History Action                  : converted
History Parameters              : from application/x-indesign to application/pdf
History Software Agent          : Adobe InDesign CS6 (Macintosh)
History Changed                 : /
History When                    : 2013:01:16 10:00:01-05:00
Derived From Instance ID        : xmp.iid:49FCEF1708206811822A92402D5D460B
Derived From Document ID        : xmp.did:BFBB06B32A2068118A6DF9B7543F7449
Derived From Original Document ID: xmp.did:BFBB06B32A2068118A6DF9B7543F7449
Derived From Rendition Class    : default
Format                          : application/pdf
Producer                        : Adobe PDF Library 10.0.1
Trapped                         : False
Has XFA                         : No
Page Count                      : 4
Creator                         : Adobe InDesign CS6 (Macintosh)

EXIF Metadata provided by EXIF.tools