Korins CRT3000 Clamp Remote Transmitter User Manual SEM3000 manual Final 150302

Korins Inc. Clamp Remote Transmitter SEM3000 manual Final 150302

User Manual

Download: Korins CRT3000 Clamp Remote Transmitter User Manual SEM3000 manual Final 150302
Mirror Download [FCC.gov]Korins CRT3000 Clamp Remote Transmitter User Manual SEM3000 manual Final 150302
Document ID2563908
Application IDMMKYzgrfrPoWtYMZFGJdGA==
Document DescriptionUser Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize42.22kB (527756 bits)
Date Submitted2015-03-23 00:00:00
Date Available2015-09-19 00:00:00
Creation Date2015-03-02 13:55:00
Producing SoftwareAcrobat Distiller 11.0 (Windows)
Document Lastmod2015-03-17 09:35:31
Document TitleMicrosoft Word - SEM3000_manual_Final_150302
Document CreatorPScript5.dll Version 5.2.2
Document Author: BFF8B8B2

SE
EM3000
0 Seriess Opera
ation M
Manual Version 2.0 (M
March 2, 2015
5)
Usin
ng a cross head or flat bladed screw
wdriver, rem
move the Sen
nder Unit ba
attery compaartment cov
ver and inserrt 3C
batteries. Press tthe RESET button
locate
ed on the re ar of the Tra
ansmitter
Slide
e the rear ba
attery compartment off the Display Unit. Insert 3 AA batteries in the Diisplay Unit.
1)Press and hold
d the CHECK
K key 5 seco
onds on the rear of the CRT3000
Transmitter unttil the red LE
ED flashes.
If yo
ou are using PIT3000 Tra
ansmitter, press [SET] bu
utton at the front
side off PIT3000 un
ntil the red LED
flashes.
2)Ch
heck the [CH
HANNEL] ke
ey located on the botto
om right han
nd side of th
he SEM30000 Display Un
nit is showin
ng. If
not, Press [MEN
NU] key to ch
hange [SET] -> [CHANN
NEL]. Press and hold the [CHANNEL]] key 3 seco
onds, Release
e the
[CHA
ANNEL] key on hearing a short beep.
3)No
ow you can see below symbol
NOW
W ENERGY sccreen on Top
pe left side.
4)Affter synchron
nization, the
e screen display as belo
ow:
key.
If your are using 99V,
please change it with
[UP][DO
OWN]
5)Press the [CHA
ANGE] key of
o Display un
nit for to sto
ore.
The
e radio wave
e icon, in the
e top left ha
and corner o
of the main screen,
will show
radio w
wave power strength.
The two units w
will now connect. Please note, this m
may take up to 2 minute
es. Once con
nnected the radio wave icon
in th
he top left o
of the screen
n will be fully
y illuminated
d and a “0” will
w be displa
ayed in the main display
y.
You can positio
on the Disp
play Unit up
p to 40 metters away frrom the CR
RT3000 Transsmitter (sub
bject to buillding
consstruction).
YOU
UR DISPLA
AY UNIT HAS 6” SCR
REEN WITH
H 5 SECTIO
ON.
The top section shows Radio Icon, Channel numbeer (1-10), 4- different Ala
arm Display and Battery
y power stre
ength
disp
play for transsmitter and receiver each.
2nd section
displays Now En
nergy with Watt
unit and
d 1 Month estimated
Co
ost with \, $$, €, ¥, £ currrency symbo
ol
mark.
U Down sym
mbol mark aand the enerrgy increase and decrea se difference on every 12
Additionally it also shows Up,
seco
onds.
Addittionally it alsso shows the
e energy con
nsumption percentage
(%)
( vs month
hly target.
Top left side shows the ene
ergy billing method
seleection from “0”
“ to “2”. “0” is the sin
ngle tariff ra
ate selection.
“1”
is 4--step tiered tariff rate se
election “2” is
i special ratte tariff selecction.
3rd section
show
ws History data
like thiis day (todaay), this wee
ek, this mon
nth and 1 m
month (31da
ays) accumulated
enerrgy consump
ption in kWh
h. The right hand side, itt shows the actual energ
gy cost of it with currency symbol mark.
Und
derneath of it, it shows today graph and this weeek graph sim
multaneously
y.
4th section
show
ws channel number, tim
me, date, weeek, month and year display.
Thee right hand side, it sh
hows
temperature (°C
C. °F) and CO
O2 emission display.
5th section show
ws touch keys.
. You will
w hear a short beep
p every time
e you presss one of the keys, [ME
ENU],
[CHA
d to help you
ANGE], [DOW
WN], [UP], [CHANNEL] and [SET]. W
We recomm
mend you usse the sound
program
m the
settiings accurately.
A. TIME/CLOCK: [C1]
1)Press and hold the [MEN
NU] key unttil you hearr a beep. [S
SET] icon will appear in
n bottom rig
ght hand co
orner
inste
ead of [CHA
ANNEL].
2)Press [SET] keyy 3 seconds and you co
ould see belo
ow symbol on
o NOW ENERGY:
3)Press [SET] keyy to see [F] [YEAR] blink
king. Press [ UP][DOWN] key to adju
ust the correect [YEAR] an
nd press [SET] to
conffirm.
4)[M
MINUTE] is blinking. Presss [UP][DOW
WN] key to ad
djust the correct [MINUT
TE] and presss [SET] to co
onfirm.
5)[H
HOUR] is blin
nking. Press [UP][DOWN] key to adju
ust the corre
ect [HOUR] and
a press [SSET] to confirrm.
6)[D
DAY] is blinking. Press [UP][DOWN] key
k to adjustt the correctt [DAY] and press [SET] tto confirm.
7)[M
MONTH] is blinking. Presss [UP][DOW
WN] key to ad
djust the adjjust [MONTH
H] and presss [SET] to co
onfirm.
8)Press [CHANG
GE] key to sto
ore.
B. TA
ARIFF SELECTION: [C2]
1)Press [MENU] key for to change
[CHA
ANNEL] -> [S
SET]
bol. Press [M
2)Press the [SET
T] key 3 seco
onds to see [F] [C1] symb
MENU] key once
to chan
nge [C1] –> [C2].
3)Press [SET] keyy to see [F] blinking to see
s [0].
Preess [UP][DOW
WN] key to select
[0] -> [2]
[0]:: Single Rate
e (Flat Rate),, [1]: 4-step Tiered Rate,, [2]: Time of
o Use Rate for
f all week((7 Day) [3] Time
of Use Rate
for weekdays
+ weekend
4)Press [CHANG
GE] to go normal display
C. TARIFF RATE FOR SINGLE (FLAT) RATE: [C3]
1)Press [MENU] key for to change [CHANNEL] -> [SET]
2)Press the [SET] key 3 seconds to see [F] [C1] symbol. Press [MENU] key 2 times to change [C1] –> [C3].
3)Press [SET] key to see [F] blinking. Press [SET] key again to see Single (Flat) rate [$0.20] on COST screen.
4)Move cursor to proper position using [MENU] key.
5)Press [UP][DOWN] key to adjust the correct value.
6)Press [MENU] to move next position and adjust the correct value. Change all the correct value continuously.
7)Press [CHANGE] to store.
D. TARIFF RATE FOR 4-STEP TIERED RATE: [C4]
TIER No.
TIER1
TIER2
TIER3
BASE BILLING
$0
THRESHOLD
0 ~ 1300kwh
1300~2300kwh
2300kwh over
RATE
$0.10/kwh
$0.16/kwh
$0.24/kwh
1)Press [MENU] key for to change [CHANNEL] -> [SET]
2)Press the [SET] key 3 seconds to see [F] [C1] symbol. Press [MENU] key 3 times to change [C1] –> [C4].
3)Press [SET] key to see [F] blinking. Press [SET] key again to see 1-STEP Tiered rate [$0.10] on COST screen.
4)Move cursor to proper position using [MENU] key.
5)Press [UP][DOWN] key to adjust the correct value.
6)Press [MENU] to move next position and adjust the correct value. Change all the correct value continuously.
7)Press [SET] to see 1-THRESHOLD Range [1300KWh].
8)Press [MENU] to move next position. And adjust the correct value Change all the value continuously.
9)Press [MENU] key to see [F] [1300kWh] blinking. Press [UP] key to change the [Tier 2] and you can see [2300
KWh].
10)You can see [$0.16] If it is okay, press [UP] key to see [$0.24] If it is okay, press [SET] key to see [00000 KWh]
11)Press change to store.
E. SET TARIFF TIME OF USE WEEK BILLING RATE: [C5]
BILLING RATE
OFF PEAK
$0.10/KWh
WEEK DAYS
MO ~ FR
MID PEAK
$0.16/KWh
WEEK ENDS
SUNDAY, SATURDAY
ON PEAK
$0.24/KWh
1)Press [MENU] key for to change [CHANNEL] -> [SET]
2)Press the [SET] key 3 seconds to see [F] [C1] symbol. Press [MENU] key to change [C1] –> [C5].
3]Press [SET] key to see [MON][TUE][WED][THU][FRI] and [F][COST] is blinking. Please change the [MID PEAK
COST $0.16/KWh]. Press [SET] to change [ON PEAK COST $0.24/KWh]
4)Press [SET] key to change [OFF PEAK COST $0.10/KWh]
5)Press [SET] key to see [SUN][SAT] and [OFF PEAK COST $0.10/KWh]. Press [SET] to change [MID PEAK COST
$016/KWh]
6)Press [CHANGE] to save it.
F. SELECT TARIFF TIME OF USE WEEK SELECTION & BILLING RATE: [C6]
1)Press [MENU] key for to change [CHANNEL] -> [SET]
2)Press the [SET] key 3 seconds to see [F] [C1] symbol. Press [MENU] key 5 times to change [C1] –> [C6].
3)Press [SET] key to see [F] blinking. Press [SET] key again to see "00:" on TIME screen.
4)Move cursor to proper position using [SET] key.
5)Press [UP][DOWN] key to adjust the Tier level, Time, Rate.
6)Press [SET] to move next position and adjust the correct value. Change all the correct value continuously.
7)Press [CHANGE] to store.
G. TARIFF RATE FOR BASIC RATE: [C7]
1)Press [MENU] key for to change [CHANNEL] -> [SET]
2)Press the [SET] key 3 seconds to see [F] [C1] symbol. Press [MENU] key 6 times to change [C1] –> [C7].
3)Press [SET] key to see [F] blinking. Press [SET] key again to see Basic rate [$0.00] on COST screen.
4)Move cursor to proper position using [MENU] key.
5)Press [UP][DOWN] key to adjust the correct value.
6)Press [MENU] to move next position and adjust the correct value. Change all the correct value continuously.
7)Press [CHANGE] to store.
H. MONTHLY KWH TARGET SETTING: [C8]
Your default setting is 300KWh.
This is useful if your household is running on a monthly budget and you need to monitor costs closely.
1)Press [MENU] key for to change [CHANNEL] -> [SET]
2)Press the [SET] key 3 seconds to see [F] [C1] symbol. Press [MENU] key to change [C1] –> [C8].
3)Press [SET] key to see [F] blinking. Press [MENU] [UP][DOWN] key to adjust the correct wattage (W).
4)Press [CHANGE] to store.
I. VOLTAGE SETTING: [C9]
Your default setting is 110 Volts.
1)Press [MENU] key for to change [CHANNEL] -> [SET]
2)Press the [SET] key 3 seconds to see [F] [C1] symbol. Press [MENU] key 8 times to change [C1] –> [C9].
3)Press [SET] key to see [F] blinking and [0 V].
Press [UP] key continuously until you reach [110V = AUTO V].
4)Press [CHANGE] to store.
*If you are using Channel 2 – 10 with PIT3000, Your CRT3000 Channel (e.g. No.1) will get the Voltage value from
PIT3000 automatically when you set the Voltage as [AUTO].
J. TEMPERATURE: [C10]
Your default setting is Centigrade, shown as °C. You can choose to display the temperature in Fahrenheit, shown
as °F.
1)Press [MENU] key for to change [CHANNEL] -> [SET]
2)Press the [SET] key 3 seconds to see [F] [C1] symbol. Press [MENU] key 9 times to change [C1] –> [C10]
3)If you want to select °C, you must select [CELSI 0]
4)If you want to select °F, you must select [FARRE 1]
5)Press [CHANGE] to save it.
K. SELECT SYMBOL for the MONEY UNIT FOR EACH COUNTRY: [C11]
1)Press [MENU] key for to change [CHANNEL] -> [SET]
2)Press the [SET] key 3 seconds to see [F] [C1] symbol. Press [MENU] key to change [C1] –> [C11].
3)Press [SET] key to see [F] blinking. Press [MENU] [UP][DOWN] key to adjust symbol for the money unit.
4)Press [CHANGE] to store. It takes 20 seconds.
L. ERASE THE KWh MEMORY (FACTORY DEFAULT SETTING): [C12]
1)Press [MENU] key for to change [CHANNEL] -> [SET]
2)Press the [SET] key 3 seconds to see [F] [C1] symbol. Press [MENU] key to change [C1] –> [C12].
3)Press [SET] key to see [F] blinking. Press [MENU] [UP][DOWN] key to adjust the correct number [0] ->[1]
4)Press [CHANGE] to store. It takes 20 seconds.
5)if you do not want to erase the kWh memory, please change [1] -> [0] and press [CHANGE].
M. GREEN HOUSE GAS UNITS:
Your SEM3000 can calculate the amount of CO2 emissions per unit of electricity used.
Existing setting:
0.42kg/kwh
N. TO REVIEW YOUR SETTINGS
1)Press [MENU] key for to change [CHANNEL] -> [SET]
2)Press the [SET] key 3 seconds to see [F] [C1] symbol. Press [MENU] key to scroll through your settings [C1] –>
[C9].
3)After review all the settings, press [MENU] to change [SET] -> [CHANNEL]
O. CALIBRATION STOP
If you do not want to save the calibration data or made mistake during the calibration procedure, please do this:
Press [MENU] key continuously and you could see normal display state without calibration.
Iden
ntify live outgoing supply cable to electricity
meeter (usually grey, red orr brown and
d located on the right ass you
look
k at the mete
er).
Unclip the Senssor and fit around live cable.
Snap tthe clip shutt to fasten securely
in p
place (see th
he images to
o the
right).
Plea
ase Note: It iis normal for the sensor to be loosee fit or be ab
ble to slide along
the caable.
Fix the
t mountin
ng bracket (o
optional) to the wall or tthe baseboa
ard used to mount yourr meter, nextt to the fuse
e box
or nearby.
Slot the Transm
mitter into itss bracket an
nd connect the Sensor cable to any one of th
he three Tran
nsmitter socckets,
located on the b
base of the unit.
The photograph
h on the righ
ht shows a typical instal lation, with the Transmittter mounted
d on it’s bra
acket to the right
of th
he meter and the Senso
or fitted arou
und the live electricity ca
able (usually grey, red orr brown).
CONGRATULA
ATIONS
You have now set up and installed yo
our SEM3000
0 successfullly. For Troubleshooting and additio
onal informa
ation
plea
ase turn overr this sheet or visit www
w.smartwattm
meter.com
Keep
p the equipm
ment out of the reach of
o children, eespecially inffants.
Insta
allation of th
his product must
be carrried out by aadults only and
if there is any doub
bt, a qualified
d electrician.
Do not install yo
our equipme
ent in a hum
mid room (b
bathroom, lau
undry, kitche
en etc.) or in
n close proximity to a ta
ap or
wate
er source. Do
o not expose the equipm
ment to mo isture, splash
hes or spray
y.
The equipment and all asssociated com
mponents arre for indoo
or use and in normal teemperature conditions only.
Avoid extreme ttemperaturess. Store away from sourcces of heat, ignition or fire.
Do not
n attempt to open, disassemble or
o repair the equipment, other than to change t he batteries.
The equipment contains a radio
transm
mitter, which may affect the operatio
on of medicaal or emergency equipm
ment.
Befo
ore using thiis equipment in a mediccal environm
ment, always seek the advice of a qu alified medical expert.
dropped.
The LCD screen is made of glass and may
m break if d
Plea
ase take special care wh
hen handling
g a damaged
d Display screen, as the
e liquid crysttals may be harmful to your
heallth.
Do not
n cover th
he ventilation
n holes on the equipme nt.
mming Guid
Plea
ase ensure yo
ou read this Installation and Program
de carefully before
using
g the equipm
ment.
If OWL+USB is used in a manner
not specified
byy 2 Save Ene
ergy Ltd, the
e protection provided by
y the equipm
ment
may
y be impaired
d.
Korrins Inc.
Rm6
608, Duncho
on-daero #47
74, Junwon-g
gu, Seongnaam City, 462-725 Korea
Tel: +82-31-777-1588
Fax: +82-31-777
7-1587
hyyh@korins.krr www.smarrtwattmeter.ccom
Korins Inc. guara
antees that the SEM3000 will work ffor a minimum period of
o 12 monthss from date of purchase
e and
that it will be free from defects
in materials,
wo
orkmanship or design. If during th
his limited 1 year perio
od of
guarantee, from
m date of pu
urchase, you find that th
he equipment is not wo
orking propeerly, you ma
ay return it to
t us
and we will replace, or, (at our
o discretio
on) repair it, free of charg
ge.
Korins Inc. will not accept any liability for defectss arising from
m fair wear and tear, aaccidental orr willful dam
mage,
misu
use or failure
e to follow product
or safety instrucctions.
If yo
ou return an
ny equipmen
nt as faulty, Korins Inc. reserves the
e right to test the equip
pment and if found to be
b in
perffect working order, to re
eturn it to yo
ou. In this eevent, Korinss Inc. reserve
es the right to charge fo
or any testin
ng or
posttage costs in
ncurred. Thiss does not affect your leegal rights re
elating to eq
quipment, wh
hich is faulty
y.
Warrranty condittions only ap
pply where Proof
of Purcchase is provvided.
To return
your S
SEM3000 co
ontact hyh@korins.kr to report the issue and re
eason for retturning yourr product. Korins
Inc. will issue yyou a form and reference numberr. Once we have receiv
ved the com
mpleted form and proo
of of
purcchase we willl commence
e the returnss process.
COMPLIANCE
The CE marking
g certifies that this prod
duct meets tthe main req
quirements of
o the Europ
pean Parliam
ment and Co
ouncil
Dire
ective 1999/5
5/EC. A copyy of the signed and dateed Declaratio
on of Conformity is avai lable on
Request.
Yourr Korins Inc. is manufacttured under an ISO 9001
1 Quality Ma
anagement System.
If so
omething is missing, please contact us: hyh@ko
orins.kr
Tha
ank you for choosing
g the SEM3000.
Follo
ow these sim
mple steps to
o set up you
ur SEM3000 and you will be able to:
Calcculate the am
mount of power being used, the ccost of that power, the amount of associated greenhouse
e gas
emisssions and d
download recorded data to your PC..
Befo
ore setting u
up your SEM3000, please
e ensure you
u carefully re
ead the Safe
ety Precautio
ons.
Before you sttart installa
ation pleasse ensure you have:
1. An electricity bill with dettails of your tariff and raates
2. A small cross head or flatt bladed scre
ewdriver
UE
ISSU
BLE CAUSE
POSSIB
TRY
T THIS
Disp
play is blank
Batterie
es
Check
they are correcctly installed
d or
replace
batteeries
“0” is
i displayed
No current detecteed
1.
1 Check Sen
nsor is corre
ectly attache
ed to
and
closed properly over
Live cable
(SEE
STEP 5))
2.
2 Check Sen
nsor is connected to Sen
nder
“•”“-----” are disp
played
Batterie
es or lost syn
nchronizatio
on
Check
batterries are correctly installe
ed or
replace
battteries or start full reset
process.
Read
dings appea
ar high
Tariff or
Read
dings appea
ar low
voltage
settings may
be
Check
your tariff and voltage setttings
incorrecct
(see
overleaff) and reset if necessaryy
Sensor not closed properly
Although
thee sensor clip maybe clo
osed,
if it is a tigh
ht fit then th
he core mayy not
close
propeerly. Check the
diamete
er of
your
cable (up to 10
0mm cable for
standard
se nsors and 17mm for large
sensor).
Reposition
tthe clip on a straight piece
of
o cable.
“-----” in display
y Unit & Trransmitter have
lost
Display
radio
link
and
repeating
STEP
onize units h
has failed
synchro
TEP
Syncchronization fails in ST
even
nt that synch
hronizing
In the unlikely
fails yo
ou will need
d to reset yo
our OWL
back to
o factory seettings and clear the
unit’s
memory
instructtions:
USB
B RATING
5Vdc
500mA
by
following
these
See
S [STEP 2]] for the pairring resetting.
INS
STALLING S
SEM3000 IN
I A 3-PHASE SUPP LY
If yo
ou have a 3--phase supp
ply you will need
two ad
dditional Sen
nsors and po
ossibly largeer sensors de
epending on
n the
size of your cab
bles. Fitting the sensorss is the sam
me process as
a above bu
ut you will n
need to identify the co
orrect
cables using the
e information below:
Insta
alling SEM30
000 in USA & JAPAN : We
W supply 2 clamps for 100V ~ 120V
V measurem
ment.
3-P
PHASE WIR
RING CODES
UK
until
Ap
pril
L1
L2
L3
Neutral
Earth
Red
Yello
ow
Blue
Black
Green/yello
ow striped
2006
Euro
ope
(green on old
o installations)
(inclu
ude
Brown
Black
Grey
Blue
Green/yello
ow striped
UK)
from
m April 2006
If yo
ou are unsu
ure about installation
please conssult a qualiffied electrician or visit www.theow
wl.com for more
information
WH
HAT IS THE
E ALARM FUNCTION
N?
We have 3 diifferent ala
arm display
y.
1)Th
he alarm function is desiigned to warn you when
n your pre-d
determined electricity
ussage peaks above
a speccified
rate. This is usefful if your ho
ousehold is running on a budget an
nd you need to monitorr costs closelly.
2)Monthly targe
et setting ovver alarm. This
is usefu l if your ho
ousehold is running on a monthly budget and you
need
d to monitor costs close
ely.
3)Bla
ack out time
e alarm. Thiss is useful fo
or to supportt the power plant & gov
vernment.
UNDERSTAND
DING TARIFFS AND TIERED TA
ARIFFS
Electricity suppliers sell elecctricity at diffferent ratess to differentt people acrross the cou
untry. Rates may also vary at
diffe
erent times o
of the night or day. The
e rate you paay for your electricity is called a “taariff” and is clearly identtified
on your
electricity bill.
Some electricity users will have primary/secondary rates based on usage. To make use of this data you will need
to calculate an average based on usage and enter this figure into tariff 1.
CAN I MONITOR APPLIANCE LEVEL?
The Sensor is unable to detect current flow when clipped an appliance lead with earth, neutral and live cables.
The sensor will only work when clipped over a live phase cable.
HOW MUCH DATA CAN BE STORED ON MY SEM3000?
Data is stored for the last 1800 days as hourly value of electricity used, cost of electricity used based on Tariff
rates entered for that day, and amount of CO2 emissions based on conversion factor for that day. This data is
accessible by connecting pc-cable and software.
Data is also stored every 12 seconds for the last 1 day and this is accessed using the automatic download
function of the software application supplied with the Display Unit.
INSTALLING THE SOFTWARE APPLICATION TO DOWNLOAD THE DATA TO PC?
Please read the User Manual on the Software Application file supplied with SEM3000. Install the software
following the installation guide in the user manual.
Follow the Getting Started section of the User Manual, to get the New Hardware installed, and to add the USB as
a “Connected To” device in the software.
HOW DO I DOWNLOAD THE DATA TO MY PC?
Simply connect the port of the Display Unit to the PC with specially made mini-USB cable, and the last 30 days
data (or number days data stored if less than 30 days) will automatically download to the software database.
HOW OFTEN DO I NEED TO DOWNLOAD THE DATA TO MY PC?
Data should be downloaded every 30days since last data download or sooner.
If 30 days is exceeded since last download, then the data for the days between the last 30 days and last
download of data will be overwritten in the monitor, hence there will be no data saved for those days in the
data
abase.
Rech
hargeable Alkaline Batte
eries can be used to opeerate your Display
Unit only few daays. Thereforre please use AC
pow
wer adapter m
mainly.
Plea
ase Note: If yyou are conccerned or co
onfused by tthe installatio
on process please
call c ustomer serrvices on _82
2-31777--1588 or email hyh@
@korins.kr
FCC ID: 2AD97-CRT3000
FCC Part 15.19
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
FCC Part 15.21
Any changes or modifications (including the antennas) to this device that are not expressly approved by the
manufacturer may void the user's authority to operate the equipment.
FCC Part 15.105 (B)
Note : This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications, However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Modifications not expressly approved by the manufacturer could void your authority to operate the
equipment under FCC rules.

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Author                          : 
Create Date                     : 2015:03:02 13:55:00+09:00
Modify Date                     : 2015:03:17 09:35:31+09:00
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03
Format                          : application/pdf
Title                           : Microsoft Word - SEM3000_manual_Final_150302
Creator                         : 
Creator Tool                    : PScript5.dll Version 5.2.2
Metadata Date                   : 2015:03:17 09:35:31+09:00
Producer                        : Acrobat Distiller 11.0 (Windows)
Document ID                     : uuid:94e9d752-1080-4690-b756-e80fc7b4ec33
Instance ID                     : uuid:f0bad3c0-e265-4e15-afa9-2efb41154f2a
Page Count                      : 14
EXIF Metadata provided by EXIF.tools
FCC ID Filing: 2AD97-CRT3000

Navigation menu