LANKE XUNTONG TECHNOLOGY PTR5618 Bluetooth low energy 4.0 modules User Manual
LANKE XUNTONG TECHNOLOGY CO.,LTD Bluetooth low energy 4.0 modules Users Manual
Contents
- 1. User Manual
- 2. User manual
User Manual
PTR5618 Coin-size Ultra Low Power Bluetooth Low Energy System on Module Embedded Cortex™ M4F 32 bit processor The PTR5618 ultra-low power Bluetooth Low Energy/ANT/2.4GHz Proprietary Multi-protocol modules based on the nRF52832 from Nordic Semiconductor. The module with an ARM® Cortex™ M4F 32 bit processor, embedded 2.4GHz transceiver, and integrated antenna, provide a complete solution with no additional RF design, allowing faster time to market, while simplifying designs, reducing BOM costs, also reduce the burden of Regulatory approvals to enter the world market. Making you more quickly into the bluetooth smart application and remove the worries. Features System on Module(SOM) base on Nordic nRF52832 Bluetooth Low Energy/ANT/2.4GHz Proprietary Multi-protocol support Complete Bluetooth Low Energy stack/profiles solution (Bluetooth 4.x and Higher) ARM® Cortex™-M4F 32 bit processor, 512 kB flash memory, 64 kB RAM 11 General Purpose I/O, Configurable mapping Pins, Simple layout of external application 12-bit/200KSPS ADC, PWM, SPI Master/Slave (8 Mbps) Low power comparator, Temperature sensor, Random Number Generator Two 2-wire Master/Slave (I2C compatible) I2S audio interface, PDM audio interface UART (w/ CTS/RTS and DMA) 20 channel CPU independent Programmable Peripheral Interconnect (PPI) Quadrature Demodulator (QDEC) 128-bit AES HW encryption 5 x 32bit Timers, 3 x 24bit Real Timer Counters (RTC), Watchdog Timer Internal RC Oscillator 32.768 kHz(± 250 ppm). No external components required Over-the-Air (OTA) firmware updates available Ultra small size(smaller than CR2032 coin battery), about 15mmx15mmx1.6mm with Antenna. COPYRIGHT ©2016 ALL RIGHTS RESERVED XunTong Tech TEL: +86 755 26675941 E-mail: nrf@freqchina.com Typical Applications: - 2.4 GHz Bluetooth low energy systems - Proprietary 2.4 GHz systems - Sports and leisure equipment - Mobile phone accessories, Connected Appliances - Health Care and Medical - Consumer Electronics, Game pads - Human Interface Devices, Remote control - Building environment control / monitoring - RFID, Security Applications,Low-Power Sensors - Bluetooth Low Energy GateWay - iBeacons™, Eddystone™, Indoor navigation - Lighting Products - Fitness devices - Wearables Quick Specifications: Bluetooth Version Bluetooth 4.x and Higher Security AES-128 Radio Frequency 2402MHz to 2480MHz Modulations GFSK at 1 Mbps, 2 Mbps data rates Transmit power -4~+4 dBm Receiver sensitivity -96 dBm (BLE mode) Antenna Integrated Current Consumption TX only @ +4 dBm, @ 3V, DC/DC enabled 7.5 mA TX only @ -4 dBm, @ 3V, DC/DC enabled 4.2 mA TX only @ +4 dBm 16.6 mA TX only @ -4 dBm 9.3 mA RX only @ 1 Mbps @ 3V, DC/DC enabled 5.4 mA RX only @ 1 Mbps 11.7 mA CPU @ 64MHz from flash 7.5 mA CPU @ 64MHz from RAM 6.7 mA CPU @ 64MHz from flash @ 3V, DC/DC 3.7 mA CPU @ 64MHz from flash RAM @ 3V, DC/DC 3.3 mA System On 1.2 μA System Off 0.7μA Additional current for RAM retention 20 nA / 4K block Operating conditions Power supply 1.7~3.6V Operating temperature -25~+85 °C COPYRIGHT ©2016 ALL RIGHTS RESERVED XunTong Tech TEL: +86 755 26675941 E-mail: nrf@freqchina.com Block diagram: Pin Description of Module(Top View): Pin No. 10 11 12 Name P0.11 P0.12 P0.13 SWDIO SWDCLK P0.17 P0.18 P0.21 GND VDD P0.26 P0.27 Description Note I/O I/O I/O Debug and flash programming I/O Debug and flash programming I/O I/O I/O Reset/ IO Power Ground Power Supply I/O I/O COPYRIGHT ©2016 ALL RIGHTS RESERVED XunTong Tech Configurable as pin reset. TEL: +86 755 26675941 E-mail: nrf@freqchina.com 13 14 15 P0.28 P0.29 P0.30 I/O I/O I/O ADC IN ADC IN ADC IN Note: An internal 4.7μF bulk capacitor has been included on the module. For those application that with heavy GPIO usage and/or current draw, it is good design practice to add additional bulk capacitance as required for your application. General Purpose I/O: The general purpose I/O is organized as one port enabling access and control of the 32 available GPIO pins through one port. Each GPIO can be accessed individually with the following user configurable features: Input/output direction Output drive strength Internal pull-up and pull-down resistors Wake-up from high or low level triggers on all pins Trigger interrupt on all pins All pins can be used by the PPI task/event system; the maximum number of pins that can be interfaced through the PPI at the same time is limited by the number of GPIOTE channels All pins can be individually configured to carry serial interface or quadrature demodulator signals Hardware RESET: There is on-chip power-on reset circuitry, But can still be used in external reset mode, in this case, GPIO pin P0.21 as an external hardware reset pin(Active Low). In order to utilize P0.21 as a hardware reset, the UICR registers PSELRESET[0] and PSELRESET[1] must be set alike, to the value of 0x7FFFFF15. When P0.21 is programmed as RESET, the internal pull-up is automatically enabled. HW debug and flash programming of Module : The Module support the two pin Serial Wire Debug (SWD) interface and offers flexible and powerful mechanism for non-intrusive debugging of program code. Breakpoints, single stepping, and instruction trace capture of code execution flow are part of this support. Pin Flash Program interface SWDIO Debug and flash programming I/O SWCLK Debug and flash programming I/O This is the hardware debug and flash programming of module, J-Link Lite support, please refer www.segger.com. COPYRIGHT ©2016 ALL RIGHTS RESERVED XunTong Tech TEL: +86 755 26675941 E-mail: nrf@freqchina.com PCB Footprint (Top View): Recommended RF Layout & Ground Plane: The module integrated antenna requires a suitable ground plane to radiate effectively. The area under and extending out from the antenna portion of the module should be kept clear of copper and other metal. The module should be placed at the edge of the PCB with the antenna edge facing out. Reducing the ground plane will reduce the effective radiated power. COPYRIGHT ©2016 ALL RIGHTS RESERVED XunTong Tech TEL: +86 755 26675941 E-mail: nrf@freqchina.com Ordering Information: Part Number Description PTR5618 Bluetooth Low Energy System on Module PTR5618-EVB Evaluation boards for module,with key, LED, I/O extend,sock for coin cell battery. Absolute Maximum Ratings: Symbol VCC_MAX VIO_MAX VIO_MAX TS Parameter Voltage on supply pin Voltage on GPIO pins (VCC > 3.6V) Voltage on GPIO pins (VCC ≤ 3.6V) Storage Temperature Range Min. Max. Unit -0.3 -0.3 -0.3 -40 3.9 3.9 VCC + 0.3V 125 °C Important Notice: Reserves the right to make corrections, modifications, and/or improvements to the product and/or its specifications at any time without notice. Assumes no liability for the user’s product and/or applications. Products are not authorized for use in safety-critical applications, including but not limited to life-support applications. ATTENTION! Electrostatic Sensitive Device Observe Precaution for handling. COPYRIGHT ©2016 ALL RIGHTS RESERVED XunTong Tech TEL: +86 755 26675941 E-mail: nrf@freqchina.com
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : Yes Author : MCU Create Date : 2016:11:21 16:11:22+08:00 Modify Date : 2016:11:21 16:11:23+08:00 Subject : Tagged PDF : Yes XMP Toolkit : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03 Metadata Date : 2016:11:21 16:11:23+08:00 Creator Tool : Acrobat PDFMaker 11 Word 版 Document ID : uuid:2ffa7854-690f-460f-bd8e-f9b472a7f8ea Instance ID : uuid:5944f1e2-38cb-429e-a516-450f9c36f3c2 Format : application/pdf Title : 内置协议及链路层、具有六路接收通道 Description : Creator : MCU Producer : Adobe PDF Library 11.0 Keywords : Source Modified : D:20161121081116 Company : Microsoft China Page Layout : OneColumn Page Count : 6EXIF Metadata provided by EXIF.tools