LANYA ELECTRONIC BSK02 BLUETOOTH SPEAKER User Manual

Download:
Mirror Download [FCC.gov]
Document ID	1703564
Application ID	Dzt1b/spxCQG+qs3b+iasg==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	10.74kB (134198 bits)
Date Submitted	2012-05-22 00:00:00
Date Available	2012-05-22 00:00:00
Creation Date	2012-05-18 11:46:33
Producing Software	Corel PDF Engine Version 14.0.0.701
Document Lastmod	2012-05-18 16:06:40
Document Title	Users Manual
Document Creator	CorelDRAW
Document Author:	Administrator

Robot bluetooth speakers
User manual
Introduction
Thank you for purchasing our Bluetooth robot
sound box of BSK02B.
The Bluetooth robot sound box is a high
quality wireless audio device that provides
users the freedom to share music and calls
whenever you want. It functions as " wireless
Bluetooth speaker " when linked to Bluetooth
phones or Bluetooth PC.
1.Speaker
2.USB
3.Volume up
4.Mic
5.Push down (play/pause music;
answer/end call)
6.Volume down
7.Led
8.ON/OFF
Operation:
1>Turn on: please dial the button to "on" and
then you can find the LED ring flashes BLUE,
also have the voice.
2>Turn off: please dial the button to "on" and
then you can find the LED ring flashes RED,
also have the voice.
3> Prepare your BSK02B for pairing: dial the
on switch in the upmost position and then
press the MFB buttons for about 6 seconds,
wait for the LED ring to flash red & blue,
that it is ready to pair.
4>Make the connection: Go to your device's
Bluetooth settings, when BSK02B appears
select it. Enter" 0000" .
5>Answer/End call: Press the MFB on your
BSK02 to both answer and end a call.
6> Reject an incoming call: press the MFB
for 2 seconds.
7>End a call: short press MFB once
8>Volume controls: increase and decrease
volume using the Plus and minus buttons
on BSK02B
9> Redial last number : Press the MFB on the
standby status.
10> Voice activated dialing: It is possible to
make a call directly from the headset using
voice recognition. To use this voice dialing
function, your mobile phone must provide
this option and corresponding voice samples
must have been recorded.
Step-1 Enable voice recognition function of
your mobile and set the mobile to standby
state.
Step-2 When no call is in progress, press and
hold the MFB until you hear a beep sound
from the BSK02B.
11> Voice transfer: Press and hold MFB for
3 seconds on talking status until to hear a
stone sound and then transfer to phone.
If need to transfer to speaker, please use
the same way.
12> Muting:mute the built- in microphone by
holding the plus and minus buttons until you
hear a beep.
13>Support A2DP but can' t support AVRCP
( It means can support play music , but
can' t support the control up and down song,
play / pause function)
Specifications:
* Bluetooth Specification v3.0 syetem
* Bluetooth® Profile Supported: HSP V1.2,
HFP V1.5, A2DP V1.2 ,
* RF Frequency Range: 2.402‐2.480GHZ,
2.4G ISM band，
* Radio Performance: Receive Sensitivity of
‐90dBm, TX Power Max 4dBm，
*Class2 bluetooth device,operating range:
Up to 10M，
*Advanced multipoint support: enables
connection to 2 phones for voice
*Multipoint A2DP streaming: enables
connection to 2 A2DP source devices for
music playback，
AUDIO:
* Frequency Response: 20 Hz ‐ 20 KHz, Very high
Signal to Noise Ratio( SNR ) : 9 5 Db, Tota
Harmonic Distortion(THD):0.1%,
* Frequency Response: 60 Hz ‐ 20 kHz
* 2W Speaker Output Level: 80dB at 0.5m,
* Built‐in Anti‐noise Microphone,
Interface：
* 4 Button design: MFB, VOL+, VOL‐, Slide
switch，
* LED Status Indicator: Blue, Red,
* Mini 5 Pin USB charging Port
* Color: green
POWER:
* Rechargeable 270mAh Li‐Polymer Battery
* Charger adapter Output: DC 5V&200mA
* Nominal charging time: Max 2 hours
* Talk time: Up to 4.5 hours
*music play time: Up to 3 hours
* Standby time: Up to 300 hours
* Dimensions (main body): ∮56mm*88mm
* Weight: 110 grams
* Operating Temperature: ‐10 ℃ ～50℃
*Storage Temperature: ‐20 ℃ ～80℃
Troubleshooting
If you cannot connect the speaker to your phone,
do as follows:
charged battery will lose its charge over time.
Leaving the device in hot or cold places, such
as in a closed car in summer or winter
conditions, will reduce the capacity and life
time of the battery.
Always try to keep the battery between 15℃
and 25℃( 59℉ and 77℉) . A device with
a hot or cold battery may not work
temporarily, even when the battery is fully
charged. Battery performance is particularly
limited in temperatures well below freezing.
Do not dispose of batteries in a fire as they
may explode. Batteries may also explode if
damaged. Dispose of batteries according to
local regulations. Please recycle when
possible. Do not dispose as household waste.
Care and maintenance
Your device is a product of superior design
and craftsmanship and should be treated
with care. The suggestions below will help
you protect your warranty coverage.
·Keep all accessories and enhancements
out of the reach of small children.
·Keep the device dry. Precipitation, humidity,
and all types of liquids or moisture can
contain minerals that will corrode electronic
· Ensure that the speaker is charged, switched
on, paired with and connected to your phone.
· Ensure that the Bluetooth feature is
activated on your phone.
· Check that the headset is within 10 meters
(30 feet ) of your phone and that there are
no obstructions between the headset and
the phone, such as walls or other electronic
devices
If no paring is made over a period of time, the
Bluetooth speaker will retreat paring mode.
You have to turn off the Bluetooth speaker
and operate again. .
Battery information
Your device is powered by a rechargeable
battery. The full performance of a new battery
is achieved only after two or three complete
charge and discharge cycles. The battery can
be charged and discharged hundreds of
times, but it will eventually wear out.
Unplug the charger from the electrical plug
and thedevice when not in use. Do not leave
a fully chargedbattery connected to a charger,
since overcharging may shorten its lifetime.
If left unused, a fully
circuits.If your device does get wet, allow it
to dry completely.
· Do not use or store the device in dusty, dirty
areas. Its moving parts and electronic
components can be damaged.
· Do not store the device in hot areas. High
temperatures can shorten the life of electronic devices, damage batteries, and warp
or melt certain plastics.
· Do not store the device in cold areas. When
the device returns to its normal temperature,
moisture can form inside the device and
damage electronic circuit boards.
· Do not drop, knock, or shake the device.
Rough handling can break internal circuit
boards and fine mechanics.
· Do ot use harsh chemicals, cleaning solvents, or strong detergents to clean the device.
· Do not paint the device. Paint can clog the
moving parts and prevent proper operation.
All of the above suggestions apply equally
to your device, battery, charger, or any
enhancement. If any device is not working
properly, take it to the nearest authorized
service facility.
FCC WARNING
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause
undesired operation.
NOTE 1: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-Consult the dealer or an experienced radio/TV technician for help.
NOTE 2: Any changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user's authority to operate the equipment.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
XMP Toolkit                     : 3.1-701
Create Date                     : 2012:05:18 11:46:33+08:00
Creator Tool                    : CorelDRAW
Modify Date                     : 2012:05:18 16:06:40+08:00
Metadata Date                   : 2012:05:18 16:06:40+08:00
Format                          : application/pdf
Creator                         : Administrator
Title                           : 机器人音响bsk02B英文说明书.cdr
Producer                        : Corel PDF Engine Version 14.0.0.701
Document ID                     : uuid:f732b623-494f-46aa-8193-f205c2c2fcc0
Instance ID                     : uuid:97ce0529-0d99-4765-b391-20e1d1231cba
Page Count                      : 3
Author                          : Administrator

EXIF Metadata provided by EXIF.tools