LCN 2030 Series Installation Guide LCN2030installationguide
User Manual: LCN LCN 2030 Series Installation Guide Installation Guide
Open the PDF directly: View PDF 
.
Page Count: 5
| Download | |
| Open PDF In Browser | View PDF |
*18758* 2030 Series 18758 15 ft-lbs No maintenance required. 2035 EN 4 = 21 N-mInstructions Installation 15 ft-lbs MAXIMUM OPENING TORQUE = 21 N-m MAXIMUM OPENING TORQUE * 1 1a 2 Installation The hand of the door and the closer must be the same. RH or LH will be stamped on the mounting plate. See the proper template for your application. * Hold open tracks 1c 1d * Hold open tracks The 2030 Series closer has been regulated priorbetoinstalled shipment. If must not on fireinstructions rated doors. adjustments are necessary, carefully follow DO NOT REMOVE THE COVER PLATE TO MAKE ADJUSTMENTS. 2a Closing Speed: See Closer Control Diagram below. 15 ft-lbs 21 N-m Regulating screw= locations are shown in illustration at left * To adjust Main Speed, turn MAXIMUMlabel. and also on door closer OPENING TORQUE regulating screw clockwise to decrease or counter-clockwise to increase. To adjust Latch Speed, turn regulating screw * Hold open tracks must to notincrease. be installed clockwise to decrease or counter-clockwise 2b Backcheck: This control hydraulically dampens the opening speed of doors. Use enough backcheck to sufficiently slow the doors opening speed. To increase resistance, turn 15 ft-lbs = 21 N-m regulating screw clockwise. * 1b Adjustment must not be installed on fire rated doors. on arm fire rated doors. Attach the arm to the closer. The bend in the will always point towards the door. 15 ft-lbs APPLIED = 21 N-m STOP BY MAXIMUM OPENING NOTTORQUE USE AN ABRUPT BACKCHECK OR EXPECT THE MAXIMUM Install the closer including the arm inOTHERS the prepped frame with LL NOTE: DO OPENING TORQUE DOOR CLOSER TO ACT AS A DOOR STOP! mounting screws provided. Be sure the mounting plate is flush with the soffit. * BACKCHECK After the closer is mounted in the door jamb, attach the 15 ft-lbs = 21 applied stop to the head frame, as shown below. The stop N-m section must have an access hole to allow for door closer MAXIMUM OPENING TORQUE adjustment. * Hold open tracks must not be installed on fire rated doors. APPLIED STOP BY OTHERS D Y S * * 3 * The track mortise in the top of the door must match the proper template. Place the roller in the track. Mount the track LATCH SPEED APPLIED in the door with holes forSTOP the BY hold open clip toward the hinge * Hold open tracks OTHERS edge. Fasten with the provided screws. must not be installed 1f Open the door approximately 45°. Pull the arm over the top of the door. Align the hole in the end of the arm with the roller stud. Fit the closer arm completely onto the roller stud and tighten the arm set screw securely. PPLIED TOP BY OTHERS APPLIED STOP BY OTHERS Hold Open Information BACKCHECK on fire rated doors. APPLIED Adjust the closing power only if more STOP BY OTHERS power is needed. The closer is shipped with minimum closing power preset. To increase the closing power turn the spring adjusting screw clockwise. Maximum adjustment is 36 turns. BACKCHECK MAIN SPEED Customer Service 1-877-671-7011 www.allegion.com Caution LATCH SPEED Improper installation or regulation may result in personal injury or property damage. Follow all instructions carefully. For questions, call LCN at BACKCHECK 877-671-7011. BACKCHECK MAIN SPEED APPLIED STOP BY OTHERS LATCH SPEED To install and adjust hold open option, see Fig. 1 and follow these MAIN SPEED directions: Tip open hold open * Hold tracksclip into track. Locate desired hold open position and fasten with screw 3. Tip cam into track & locate as shown. Fasten with must not be installed * Hold open tracks LATCH on firedoor ratedinto doors. screw 1. Push hold open position and check for proper operation. SPEED must not be BACKCHECK installed on fire rated doors. To increase holding power, loosen screw and slide cam toward latch edge of door. To decrease holding power, slide cam toward hinge edge. ReMAIN SPEED tighten screw 1. 1e 1g MAIN SPEED LATCH SPEED BACKCHECK MAIN SPEED LATCH SPEED © Allegion 2014 Printed in U.S.A. 18758 Rev. 01/14-k 4 09/06 (85°) 17.000 Front 4.25 PAGE 4 PAGE 1 Front 11.000 11.000 17.000 folded SHEET PAGE 2 PAGE 3 11.000 BEGINNING SHEET Additional Notes: 1. None Revision History K L M N P R Revision Description: K > Revised Artwork 042801 Material White Paper Notes 1. printed two sides 2. printed black 3. tolerance ± .13 4. printed in country may vary 5. drawings not to scale Edited By Approved By EC Number Release Date D. Myers M. Sasso 042801 01-01-14 Title 2030 Series Installation Instructions Creation Date 05-10-10 Created By N/A Software: InDesign CS6 Number Revision 18758 Activity 3899 Hancock Expwy Security, CO 80911 k © Allegion 2014
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes XMP Toolkit : Adobe XMP Core 5.3-c011 66.145661, 2012/02/06-14:56:27 Create Date : 2013:12:04 09:59:26-07:00 Metadata Date : 2013:12:04 09:59:29-07:00 Modify Date : 2013:12:04 09:59:29-07:00 Creator Tool : Adobe InDesign CS6 (Windows) Instance ID : uuid:dc2cce5f-40b1-4576-9520-f3dde025de26 Original Document ID : xmp.did:516915126ECCE1118A0D8AD340C27D6B Document ID : xmp.id:7C7B586A055DE31188789A283E7D051F Rendition Class : proof:pdf Derived From Instance ID : xmp.iid:7B7B586A055DE31188789A283E7D051F Derived From Document ID : xmp.did:47A44EA0A139E21197309D1C525C39AC Derived From Original Document ID: xmp.did:516915126ECCE1118A0D8AD340C27D6B Derived From Rendition Class : default History Action : converted History Parameters : from application/x-indesign to application/pdf History Software Agent : Adobe InDesign CS6 (Windows) History Changed : / History When : 2013:12:04 09:59:26-07:00 Format : application/pdf Producer : Adobe PDF Library 10.0.1 Trapped : False Page Count : 5 Creator : Adobe InDesign CS6 (Windows)EXIF Metadata provided by EXIF.tools