LCN 4410ME Installation Guide LCN4410MESeries Instructions

User Manual: LCN LCN 4410ME Installation Guide Installation Guide

Open the PDF directly: View PDF .
Page Count: 5

*15022*

15022

© Allegion 2014

Printed in U.S.A.

15022 Rev. 01/14-h

Door closer with electronic release & Multi-point hold open

4410ME Series

Installation Instructions

1 Closer Installation

1a Closer Information

Closer is handed at the factory. The hand of the closer must

match the hand of the door (see the door handing diagram below).

Determine the closer mounting template to use - Standard or Flush-

Ceiling (see page 4). Refer to the proper template for the entire

installation

1b Voltage

Voltage supplied to the door frame MUST match voltage of the

solenoid.

1c Before beginning this step, determine which

type of wiring option will be used, and follow the

corresponding instructions:

Concealed Wiring: see Figure 3

on page 3.

a. Prepare the frame per the

proper template on page

4. Be sure all the holes are

dimensioned correctly before

drilling and tapping.

b. Assemble the conduit

connector provided to the

exible conduit, then attach to

the hole in the mounting plate.

c. Secure the mounting plate

to the frame with the screws

provided.

Surface Wiring: see Figure 4 on page 3.

LNOTE: Remove the knockout in the top of the cover.

a. Prepare the frame per the proper template on page 4. Be sure

all the holes are dimensioned correctly before drilling and

tapping.

b. Secure the mounting plate to the frame with the screws

provided.

c. Attach the surface run Z\x” EMT conduit to the hole in the

bracket on the mounting plate. Be sure the conduit is securely

attached to the bracket.

1d Wiring Connections

Make the wiring connections at this time. Connect the two black

wires to the input voltage (polarity is not important). The green wire

MUST be connected to an earth ground (see Figures 3 & 4 on page

3).

1e Main Arm

Place the main arm onto the shaft, approximately 90° to the closer

body, and secure with the arm shaft screw.

1f Rod & Shoe

Attach the rod and shoe to the door, per the proper template on

page 4, with the provided screws.

1g Insert the Rod

Open the door partway and insert the rod into the forearm, then

close the door. Pull the Main Arm to a right angle (90°) to the door,

insert the arm set screw, and tighten securely.

1h Regulate the Closer

Regulate the closer and perform the electrical checkout, as

instructed on page 2, before installing the closer cover.

HOW TO TELL HAND OF DOOR:

LEFT

HAND

DOOR

RIGHT

HAND

DOOR

MAXIMUM OPENING FORCE

=

33 ft-lbs

45 N-m

58 N

WARNING

!

HAZARDOUS VOLTAGE

CAN SHOCK AND CAUSE

SEVERE INJURY

Disconnect power before

making any electrical

connections or performing

maintenance.

Customer Service

1-877-671-7011 www.allegion.com/us

2 Regulation Instructions

See Figure 2 on the opposite page for regulating screw

location, door control diagram & spring power adjustment

2a Spring Power Adjustment

DO NOT ALLOW THE DOOR TO SLAM INTO THE FRAME. The

spring power should be adjusted only if more power is needed to

close the door. Turning the spring adjustment B\cx” Allen Wrench

clockwise will increase the spring power. Maximum adjustment is

six (6) turns.

2b Regulation

A “normal” closing time from a 90° position is five (5) to seven

(7) seconds, equally divided between the MAIN and LATCH

SPEED. If adjustments are needed, use a C\cx” Allen Wrench. To

adjust the MAIN SPEED, turn the regulating screw clockwise to

slow the door speed, or counterclockwise to increase the door

speed. LATCH SPEED is adjusted the same way. When adjusting

the BACKCHECK, use the least amount of force necessary

to sufficiently slow the swing of the door.To adjust the closer

BACKCHECK, turn the regulating screw clockwise to increase

the amount of force, or counterclockwise to reduce the amount of

force. DO NOT USE THE ABRUPT BACKCHECK SETTING OR

EXPECT THE CLOSER TO ACT AS A STOP!

CAUTION

Improper installation or regulation may result in personal

injury or property damage. Follow all instructions carefully.

For questions, call LCN at

877-671-7011

3 Electrical Checkout

After completion of installation & wiring, and with the unit

properly powered, perform the following tests:

3a Hold Open the Door

With power on, open the door any position and release. The door

should remain in the hold-open position within 10°. For a bypass

model to hold open, the door must be opened beyond the degree of

the door swing indicated on the label.

3b Door

If the door does not remain in the hold open position, push the on/

off switch. If the door still does not hold open, verify the proper

voltage input at the solenoid leads.

3c Power Release

Turn the power off. The door should close completely.

3d Manual Release

To release manually, pull rmly on the door. The door should close

completely.

3e Rechecking the System

The system should be checked at regular intervals. It is

recommended that steps 3a-3c be repeated every 90 days.

4 Electrical Data for Door Holder Solenoid

24V AC-DC Nominal +10% - 15% @ 0.075 Amp. Max.

120V AC-DC Nominal +10% - 15% @ 0.030 Amp. Max.

24 V Hold Open Force Adjustment

If the door is hard to pull out of the hold open position, adjust as

shown.

IMPORTANT

The closer leaves the factory set at a maximum holding force.

The holding force may be decreased and increased again, but

it cannot be increased beyond the original setting.

Turn

counterclockwise

to decrease

the holding force

+

Figure 1

Figure 2

4 erugiF3 erugiF

Cover

Mounting Bracket For

Surface Run Conduit

Hole For

Concealed

Conduit

Connection

Rod & Shoe

Assembly

Arm

Set

Screw

Cover

Screws

Arm

Shaft

Screw

Arm

Assy.

Spring

Power

Adjust.

Latch

Speed

Main

Speed

Backcheck

Connect Green

Wireto Earth

Ground Connect Black

Wires to Input

Voltage Leads

(Polarity Not

Important)

Connect Black

Wires to Input

Voltage Leads

(Polarity Not

Important)

Connect Greenwire

To Earth Ground

1

2

3

Backcheck

Main

Speed

Latch

Speed

6

Turns

Max.

To Increase Closing Power

HOLD OPEN ANY POINT TO 150°

HOLD OPEN BYPASS 80° OR 140°

HOLD OPEN ANY POINT TO 170°

HOLD OPEN BYPASS 80° OR 140°

HOLD OPEN ANY POINT TO 150°

HOLD OPEN BYPASS 80° OR 140°

HOLD OPEN ANY POINT TO 170°

HOLD OPEN BYPASS 80° OR 140°

NOTES-

1.

2.

3.

4.

5.

6.

7.

Voltage supplied to unit must match voltage shown on Sentronic label.

Locate closer and shoe from of pivot when pivots are used. For use

with swing clear hinges, consult factory.

Auxiliary stop is recommended. For use with overhead stops, shoe

must be lowered to clear holder.

Long arm required for opening beyond 160°. Reveal not exceed 3 "

(5 " FRAME).

Maximum stop thickness is ".

Electric connector provided by LCN.

Reinforcing per ANSI\SDI - 100 is recommended for hollow metal

door and frames.

7/8

3/4

5/8

C

L

®

®

HAZARDOUS VOLTAGE

CAN SHOCK AND

CAUSE SEVERE INJURY

Disconnect power before

making any electrical

connections or performing

maintenance.

WARNING

!

4410 ME

Additional Notes: Revision History Revision Description:

H > Revised artwork

1. None G H J K L M

038791 043228

Material

White Paper

Edited By Approved By EC Number Release Date

D. Myers M. Sasso 043228 01-01-14

Notes

1. printed two sides

2. printed black

3. tolerance ± .13

4. printed in country may vary

5. drawings not to scale

Title

4410ME Series Instruction Sheet

Creation Date

05-10-10

Number

15022

Revision

H

Created By

N/A Activity

3899 Hancock Expwy

Security, CO 80911 © Allegion 2014Software: InDesign CS6

17.00 4.25

11.000 11.000

BEGINNING SHEET FOLDED SHEET

Front

Page 1 Page 2 Page 3 Page 4

Back