LCN 4410ME Installation Guide LCN4410MESeries Instructions
User Manual: LCN LCN 4410ME Installation Guide Installation Guide
Open the PDF directly: View PDF 
.
Page Count: 5
| Download | |
| Open PDF In Browser | View PDF |
*15022* 4410ME Series 15022 Door closer with electronic release & Multi-point hold open 1 Closer Installation 1a Closer Information Closer is handed at the factory. The hand of the closer must match the hand of the door (see the door handing diagram below). Determine the closer mounting template to use - Standard or FlushCeiling (see page 4). Refer to the proper template for the entire installation 1b Voltage Voltage supplied to the door frame MUST match voltage of the solenoid. 1c Before beginning this step, determine which type of wiring option will be used, and follow the corresponding instructions: ! Concealed Wiring: see Figure 3 on page 3. a. Prepare the frame per the proper template on page 4. Be sure all the holes are dimensioned correctly before drilling and tapping. b. Assemble the conduit connector provided to the flexible conduit, then attach to the hole in the mounting plate. c. Secure the mounting plate to the frame with the screws provided. Warning Installation Instructions Surface Wiring: see Figure 4 on page 3. LL NOTE: Remove the knockout in the top of the cover. a. Prepare the frame per the proper template on page 4. Be sure all the holes are dimensioned correctly before drilling and tapping. b. Secure the mounting plate to the frame with the screws provided. c. Attach the surface run Z\x” EMT conduit to the hole in the bracket on the mounting plate. Be sure the conduit is securely attached to the bracket. 1d Make the wiring connections at this time. Connect the two black wires to the input voltage (polarity is not important). The green wire MUST be connected to an earth ground (see Figures 3 & 4 on page 3). 1e Disconnect power before making any electrical connections or performing maintenance. Main Arm Place the main arm onto the shaft, approximately 90° to the closer body, and secure with the arm shaft screw. 1f HAZARDOUS VOLTAGE CAN SHOCK AND CAUSE SEVERE INJURY Wiring Connections Rod & Shoe Attach the rod and shoe to the door, per the proper template on page 4, with the provided screws. 1g Insert the Rod Open the door partway and insert the rod into the forearm, then close the door. Pull the Main Arm to a right angle (90°) to the door, insert the arm set screw, and tighten securely. 1h Regulate the Closer Regulate the closer and perform the electrical checkout, as instructed on page 2, before installing the closer cover. HOW TO TELL HAND OF DOOR: LEFT HAND DOOR RIGHT HAND DOOR = 33 ft-lbs 45 N-m 58 N MAXIMUM OPENING FORCE Customer Service 1-877-671-7011 www.allegion.com/us © Allegion 2014 Printed in U.S.A. 15022 Rev. 01/14-h 2 Regulation Instructions See Figure 2 on the opposite page for regulating screw location, door control diagram & spring power adjustment 2a Spring Power Adjustment DO NOT ALLOW THE DOOR TO SLAM INTO THE FRAME. The spring power should be adjusted only if more power is needed to close the door. Turning the spring adjustment B\cx” Allen Wrench clockwise will increase the spring power. Maximum adjustment is six (6) turns. 2b Regulation A “normal” closing time from a 90° position is five (5) to seven (7) seconds, equally divided between the MAIN and LATCH SPEED. If adjustments are needed, use a C\cx” Allen Wrench. To adjust the MAIN SPEED, turn the regulating screw clockwise to slow the door speed, or counterclockwise to increase the door speed. LATCH SPEED is adjusted the same way. When adjusting the BACKCHECK, use the least amount of force necessary to sufficiently slow the swing of the door.To adjust the closer BACKCHECK, turn the regulating screw clockwise to increase the amount of force, or counterclockwise to reduce the amount of force. DO NOT USE THE ABRUPT BACKCHECK SETTING OR EXPECT THE CLOSER TO ACT AS A STOP! Caution Improper installation or regulation may result in personal injury or property damage. Follow all instructions carefully. For questions, call LCN at 877-671-7011 3 Electrical Checkout After completion of installation & wiring, and with the unit properly powered, perform the following tests: 3a Hold Open the Door With power on, open the door any position and release. The door should remain in the hold-open position within 10°. For a bypass model to hold open, the door must be opened beyond the degree of the door swing indicated on the label. 3b Door If the door does not remain in the hold open position, push the on/ off switch. If the door still does not hold open, verify the proper voltage input at the solenoid leads. 3c Power Release Turn the power off. The door should close completely. 3d Manual Release To release manually, pull firmly on the door. The door should close completely. 3e Rechecking the System The system should be checked at regular intervals. It is recommended that steps 3a-3c be repeated every 90 days. 4 Electrical Data for Door Holder Solenoid 24V AC-DC Nominal +10% - 15% @ 0.075 Amp. Max. 120V AC-DC Nominal +10% - 15% @ 0.030 Amp. Max. 24 V Hold Open Force Adjustment If the door is hard to pull out of the hold open position, adjust as shown. Important The closer leaves the factory set at a maximum holding force. The holding force may be decreased and increased again, but it cannot be increased beyond the original setting. + Turn counterclockwise to decrease the holding force Figure 1 Mounting Bracket For Surface Run Conduit Cover Spring Power Adjust. Hole For Concealed Conduit Connection Rod & Shoe Assembly Arm Assy. Arm Set Screw Arm Shaft Screw Cover Screws Backcheck Figure 2 Main Speed 1 2 Latch Speed Main Speed 3 Latch Speed Backcheck To Increase Closing Power Figure 3 Connect Green Wireto Earth Ground 6 Turns Max. Figure 4 Connect Black Wires to Input Voltage Leads (Polarity Not Important) Connect Black Wires to Input Voltage Leads (Polarity Not Important) Connect Greenwire To Earth Ground 4410 ME HOLD OPEN ANY POINT TO 150° HOLD OPEN BYPASS 80° OR 140° HOLD OPEN ANY POINT TO 170° HOLD OPEN BYPASS 80° OR 140° HOLD OPEN ANY POINT TO 150° HOLD OPEN BYPASS 80° OR 140° HOLD OPEN ANY POINT TO 170° HOLD OPEN BYPASS 80° OR 140° ! WARNING HAZARDOUS VOLTAGE CAN SHOCK AND CAUSE SEVERE INJURY Disconnect power before making any electrical connections or performing maintenance. NOTES1. Voltage supplied to unit must match voltage shown on Sentronic® label. 2. Locate closer and shoe from CL of pivot when pivots are used. For use with swing clear hinges, consult factory. 3. Auxiliary stop is recommended. For use with overhead stops, shoe must be lowered to clear holder. 4. Long arm required for opening beyond 160°. Reveal not exceed 3 7/8" (5 3/4" FRAME). 5. Maximum stop thickness is 5/8". 6. Electric connector provided by LCN. 7. Reinforcing per ANSI\SDI - 100 is recommended for hollow metal door and frames. ® 4.25 17.00 Back Front Page 1 Page 2 Page 3 Page 4 11.000 BEGINNING SHEET folded SHEET Additional Notes: 1. None 11.000 Revision History G H 038791 043228 Material J K White Paper Notes 1. printed two sides 2. printed black 3. tolerance ± .13 4. printed in country may vary 5. drawings not to scale L M Revision Description: h > Revised artwork Edited By Approved By EC Number Release Date D. Myers M. Sasso 043228 01-01-14 Title 4410ME Series Instruction Sheet Creation Date 05-10-10 Created By N/A Software: InDesign CS6 Number Revision 15022 Activity 3899 Hancock Expwy Security, CO 80911 h © Allegion 2014
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes XMP Toolkit : Adobe XMP Core 5.3-c011 66.145661, 2012/02/06-14:56:27 Create Date : 2014:01:02 09:23:17-07:00 Metadata Date : 2014:01:02 09:23:19-07:00 Modify Date : 2014:01:02 09:23:19-07:00 Creator Tool : Adobe InDesign CS6 (Windows) Instance ID : uuid:40672c71-d30f-4176-85d9-3e8c00b83c62 Original Document ID : xmp.did:516915126ECCE1118A0D8AD340C27D6B Document ID : xmp.id:306D812DCA73E311B4D0E88C51DF512F Rendition Class : proof:pdf Derived From Instance ID : xmp.iid:2F6D812DCA73E311B4D0E88C51DF512F Derived From Document ID : xmp.did:47A44EA0A139E21197309D1C525C39AC Derived From Original Document ID: xmp.did:516915126ECCE1118A0D8AD340C27D6B Derived From Rendition Class : default History Action : converted History Parameters : from application/x-indesign to application/pdf History Software Agent : Adobe InDesign CS6 (Windows) History Changed : / History When : 2014:01:02 09:23:17-07:00 Format : application/pdf Producer : Adobe PDF Library 10.0.1 Trapped : False Page Count : 5 Creator : Adobe InDesign CS6 (Windows)EXIF Metadata provided by EXIF.tools