LCN 6030 Series Installation Guide LCN6030Installationguide
User Manual: LCN LCN 6030 Series Installation Guide Installation Guide
Open the PDF directly: View PDF 
.
Page Count: 5
| Download | |
| Open PDF In Browser | View PDF |
*18503* Fig. 1 6030 Series 18503 Fig. 2 Closer Fig. 1 Fig. 2 Track Snubber Roller Closer Bumper Set Screw Top Pivot Fig. 3 Arm Arm Screw Top Of Frame Arm Screw Bumper Top Of Frame Top Pivot Fig. 1 Track Installation Instructions Top Of Frame Arm Clamp Bolt Roller Stud Set Screw Set Screw Fig. 3 Arm Arm Clamp Bolt Closer Roller Stud Fig. 2 Top Pivot Door Leaf Top Pivot Door Leaf Track Top Of Door Top Of Door Snubber Roller Bumper Set Screw Top Pivot 1 5 Set Screw Prepare door and frame to recieve pivot and closer, per templates on Arm and closer. Fig. 3 pages 2 and 3. Install pivot 2 Arm Screw Arm Clamp Bolt Roller Stud Set Screw Bumper (and optional hold-open, when ordered) are factory installed. If a different degree of opening is required, follow step 2A. Insert roller first, then snubber in track as shown in FIG. 2. Install track in door mortise using screws provided. Tighten screws. • Slide bumper 3 away from post 2. Remove screw 1 and post 2, and reinstall in hole indicated above, tighten screw. Slide bumper 3 against post 2. 3 Door should now be hung on pivots. Refer to pivot installation sheet for details. Top door to 45°. Pull arm toward Top door and slide roller stud under hole in Open Pivot Of arm. DoorInstall stud in arm with slot Doorcrosswise as shown in FIG. 3. Turn set Leaf in just enough to retain roller stud, but do not tighten firmly. Allow screw door to close, and with arm horizontal, tighten arm clamp bolt (at shaft end of arm) with hex key provided. 6 Closed door should be centered in frame. If not, open door part way and rotate roller stud about an eighth of a turn, using a screwdriver. (Set screw may need to be backed out slightly.) Repeat as needed till centered as required. When satisfied, tighten arm set screw securely. (When doors are paired, adjust both until edges match.) Open door, slide snubber into track at least 6” in from end. Allow door to close. This will automatically position the snubber correctly. 7 7a Location Adjustment of Hold Open Device Slide bumper 3 away from pivot edge of door. Remove screw 1, post 2, adjusting cam 4, and screw 5. Slide holding clip 6 to locate screw holes over tapped holes in track as indicated below. Insert screw 5 and tighten securely. Replace cam 4, post 2, and screw1, tighten securely. Slide bumper 3 against post 2. 4 Attach arm to closer shaft with arm screw. Tighten screw securely. Caution Closer arm is under strong pressure to return. Hold it firmly during the next step. 7b Intensity Adjustment of Hold Open Device Test for release at hold open position. If holding force must be INCREASED, loosen screw 1 a quarter turn and slide cam 4 AWAY from pivot edge of door. Retighten screw 1 securely. For DECREASED holding force, cam 4 must be moved TOWARD pivot edge of door S Rolle Backcheck Regulation: 7c Main Speed 7d Latch Speed 7e To regulate main swing speed: There is one main swing speed adjusting screw for both swings of door. If adjustment is required, turn screw clockwise to slow down main swing of door. To speed up main swing, turn screw counterclockwise. A normal closing time from 90° open position is 5 to 7 seconds, evenly divided between main swing speed and latch swing speed. Use a C\cx” hex wrench. To regulate latch swing speed: There are two latch swing speed adjusting screws. Refer to diagram to identify hand Backhand) Checkor RH (right of swing, and use screw marked LH (left hand). If adjustment is required, turn appropriate screw clockwise to slow down latch swing. To speed up latch swing, turn screw counterclockwise. RH Latch Speed To adjust backcheck intensity: There is one backcheck adjustment screw for both swings of door. Adjust to lightest backcheck that will retard door opening speed during the last few degrees of opening. CAUTION: Do not set an abrupt backcheck or expect closer to act as a door stop. To increase backcheck, turn screw clockwise. To reduce backcheck, turn screw counterclockwise. Opening Left Hand Main Swing Of Door Main Speed LH Latch Speed Ba Latching Speed Latching Speed Backcheck RH Latch Speed Right Hand Main Swing Of Door Opening Left Hand Main Swing Opening Of Door Main Speed LH Latch Speed Back Check Backcheck Latching Speed Caution IMPROPER INSTALLATION OR REGULATION MAY RESULT IN PERSONAL INJURY OR PROPERTYLatching DAMAGE. FOLLOW ALL INSTRUCTIONS CAREFULLY.Speed FOR QUESTIONS, CALL LCN AT 877-671-7011 RH Latch Speed Right Hand Main Swing Of Door Closing Power Adjustment Closer is shipped with minimum closing power, and power of each swing can be individually increased. To adjust, use spring adjustment screw that corresponds with hand of swing in regulation diagram. To increase, turn screw clockwise. Maximum adjustment is 36 turns. Table of Sizes Maximum width of doors Exterior Interior Catalog No. of Closer ---- 38” (965 mm) 6033 36” (900 mm) 48” (1220 mm) 6034 42” (1065 mm) 54” (1370 mm) 6035 Opening Backcheck LL NOTE: Specify next higher closer where strong drafts exist. Customer Service 1-877-671-7011 www.allegion.com/us © Allegion 2014 Printed in U.S.A. 18503 Rev. 01/14-h 17.00 FRONT Page 2 Page 3 Page 4 11.000 BEGINNING SHEET Page 1 4.25 Front 11.00 folded SHEET Additional Notes: 1. None Revision History H J K L M N Revision Description: h > Revised artwork 043228 Material White Paper Notes 1. printed two sides 2. printed black 3. tolerance ± .13 4. printed in country may vary 5. drawings not to scale Edited By Approved By EC Number Release Date D. Myers M. Sasso 043228 01-01-14 Title 6030 Series Instruction Sheet Creation Date 05-10-10 Created By N/A Software: InDesign CS6 Number Revision 18503 Activity 3899 Hancock Expwy Security, CO 80911 h © Allegion 2014
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes XMP Toolkit : Adobe XMP Core 5.3-c011 66.145661, 2012/02/06-14:56:27 Create Date : 2014:01:02 09:26:45-07:00 Metadata Date : 2014:01:02 09:26:48-07:00 Modify Date : 2014:01:02 09:26:48-07:00 Creator Tool : Adobe InDesign CS6 (Windows) Instance ID : uuid:3bda6326-2e27-4c6f-81a6-851f140fc303 Original Document ID : xmp.did:516915126ECCE1118A0D8AD340C27D6B Document ID : xmp.id:2D7914A7CA73E311B4D0E88C51DF512F Rendition Class : proof:pdf Derived From Instance ID : xmp.iid:2C7914A7CA73E311B4D0E88C51DF512F Derived From Document ID : xmp.did:47A44EA0A139E21197309D1C525C39AC Derived From Original Document ID: xmp.did:516915126ECCE1118A0D8AD340C27D6B Derived From Rendition Class : default History Action : converted History Parameters : from application/x-indesign to application/pdf History Software Agent : Adobe InDesign CS6 (Windows) History Changed : / History When : 2014:01:02 09:26:45-07:00 Format : application/pdf Producer : Adobe PDF Library 10.0.1 Trapped : False Page Count : 5 Creator : Adobe InDesign CS6 (Windows)EXIF Metadata provided by EXIF.tools