LCN 376\377\000E\000l\000e\000c\000t\000r\000o\000m\000e\000c\000h\000a\000n\000i\000c\000a\000l\000 \000P\000o\000w\000e\000r\000e\ Electromechanical Auto Operator Series Product Guide LCNelectromechanicalautooperatorguide
User Manual: LCN LCN Electromechanical Auto Operator Series Product Guide Product Guide
Open the PDF directly: View PDF .
Page Count: 66
Download | |
Open PDF In Browser | View PDF |
LCN ELECTROMECHANICAL POWERED SYSTEMS GENERAL ELECTRICAL DATA 1. Input power 115 volt, 3 wire, single phase, 60Hz, fused, 15 amp supply. 2. UL approved type flexible conduit is recommended for the 115 volt power line. 3. The 115 volt power supply must be a dedicated circuit from the main circuit breaker panel and must not be connected into a building lighting system operating fluorescent lights. 4. Location of conduits determined by mounting. See installation instructions for location. 2800, 9500 Series ELECTRICAL DATA 1. 120 VAC input @ 2.5 amps (2800, and 9500 Series). 2. 24 V AC output @ 1.5 amps (protected by self-resetting thermal fuse). 3. 24 V DC available with SO kit included. 9100 Series ELECTRICAL DATA 1. 120 VAC input @ 1 amp. 2. 24 VDC output @ 2.5 amps on premium control box. 55 LCN CLOSERS 121 W. RAILROAD AVE. P.O. BOX 100 PRINCETON, IL, USA 61356-0100 PHONE 800-526-2400 FAX 800-248-1460 www.lcn.ingersollrand.com 3/10 Notes 56 LCN CLOSERS 121 W. RAILROAD AVE. P.O. BOX 100 PRINCETON, IL, USA 61356-0100 PHONE 800-526-2400 FAX 800-248-1460 www.lcn.ingersollrand.com 3/10 LCN BENCHMARK UNIQUE FEATURES Dual Independent Program Memories Each unit is pre-programmed to factory default settings. The installer can adjust the unit to meet the job site requirements. These field settings are locked into the computer’s memory. Any subsequent field adjustments replace the original field adjustments. The factory settings are always retained in memory and can be recalled to replace the field settings in just seconds, restoring the unit to its original programming. On-Board Power Supply Provides 24V DC output to power card readers, manual actuators and other peripherals. Electronic Circuit Protection Fused input circuit protection and fused output protection for 24 VDC peripherals Visual Function Indicators There are 2 LED s for installation and trouble shooting feedback. The motor LED will illuminate when the motor drive circuit energizes this is when the operator is activated it will remain on only during the opening of the door and the power LED this will illuminate when power is applied to the board and remains illuminated as long as there is power applied to the board. Programming Mode Allows tailoring the following functions to meet specific site conditions: Power Boost Opening Speed Backcheck Speed Hold Open Time Delay Backcheck Position Closing Speed Latch Position Push ‘N Go Delayed Activation 57 LCN CLOSERS 121 W. RAILROAD AVE. P.O. BOX 100 PRINCETON, IL, USA 61356-0100 PHONE 800-526-2400 FAX 800-248-1460 www.lcn.ingersollrand.com 3/10 Notes 58 LCN CLOSERS 121 W. RAILROAD AVE. P.O. BOX 100 PRINCETON, IL, USA 61356-0100 PHONE 800-526-2400 FAX 800-248-1460 www.lcn.ingersollrand.com 3/10 The 9130 BENCHMARK by LCN is an electrically powered low-energy operator. It provides easy access for people with disabilities, the elderly or the frail. Designed primarily for automatic opening applications that occasionally require manual opening. The BENCHMARK is a cost-effective solution for retrofitting an activated or manual door. SINGLE DOOR, SURFACE MOUNT (PULL) OFFSET PIVOT/BUTT HINGE FEATURES LCN 9130 SERIES Push ‘N Go permits non-switch activation Microprocessor control box ensures reliability and maintains customer settings Power Boost allows for increased closing force near latch 9130 series operator is shipped with motor gearbox, control box, mounting plate, standard arm, metal cover, standard track, wood and machine screws. Actuators available separately, see page 121. 9130 Series is fully compliant with UL 325 and meets the provisions of ANSI A156.19. The 9130 Series is UL listed for fire-rated applications. The 9130 Series also meets the provisions of the Americans with Disabilities Act. Single interior door, surface mounted. ADA compliant. On/Off switch included as standard. Non-handed for either right or left swinging door. 27” cover is standard, 36” optional. All potentiometers clearly labeled with their functions. LED lights indicate power to control box and motor gearbox. SU 59 FINISH COVER ARM FUNCTION ST AN D RE AR GU D ( SI L DO AR NG ( UB DO LE) U L OF E E BL GR E) FS ES E S CE T PI NT VO (PU SH T ER PI ARM /PU VO LL T ) AR M HANDING RF A SU CE RF MO A UN SU CE T RF MO SI AC UN NG LE CO E T NC MO SIM DO EA UN UL OR T CO LE T NC D S IND ANE CO EAL ING EPE OUS N NC ED LE P DO DEN AIR EA SI T LE MU OR PA D IR IN LTA DE NE HA PE OU ND ND S NO ED EN PAI R NT PA HA IR ND ED ST AN CU DAR ST D A O CU M NO ST AN DIZ OM OD ED PA IZED IN M T ET AL MOUNTING LCN CLOSERS 121 W. RAILROAD AVE. P.O. BOX 100 PRINCETON, IL, USA 61356-0100 PHONE 800-526-2400 FAX 800-248-1460 www.lcn.ingersollrand.com 3/10 MOUNTING DETAILS LCN 9130 SERIES TOP JAMB SINGLE DOOR (OFFSET/BUTT HINGE, CENTER PIVOT, PULL, STANDARD COVER) MOUNTING 6" MIN. 152 MM FROM TOP OF DOOR OPENING TO CEILING 4 3/4" 121 MM PULL ARM ASS'Y 4 1/2" 114 MM 5/8" FROM TOP OF DOOR 27" OPERATOR OPERATOR OFFSET PIVOT OR BUTT HINGES 28 1/2" PULL CHANNEL DOOR FRAME TOP JAMB SINGLE DOOR (OFFSET/BUTT HINGE, CENTER PIVOT, PULL, FULL COVER) MOUNTING Template allows 90 degree power opening and 90 degree manual opening. 6" MIN. 152 MM FROM TOP OF DOOR OPENING TO CEILING 4 3/4" 121 MM PULL ARM ASS'Y FULL LENGTH OPERATOR MAXIMUM OPENING DOOR 4 1/2" 114 MM 5/8" FROM TOP OF DOOR OFFSET PIVOT OR BUTT HINGES OPERATOR 28 1/2" PULL CHANNEL DOOR FRAME DOOR Butt Hinges should not exceed 5” (127 mm) in width. Reveal should not exceed 1/8” (3 mm). Head Frame minimum 2” (51 mm). Top Rail minimum 2” (51 mm). Opening and Closing Time are variable by adjustments to the electronic control module located on the operator assembly. Maximum hold open time adjustable up to approximately 30 seconds. System Diagram see “AUTOMATIC OPERATORS” section pages 52-54 for typical system wiring and page 55 for electrical data. Special Templates Customized installation templates or products may be available to solve unusual applications. Contact LCN for assistance. Please consult your local SSC representative or LCN for assistance with specific installations and material requirements. 60 LCN CLOSERS 121 W. RAILROAD AVE. P.O. BOX 100 PRINCETON, IL, USA 61356-0100 PHONE 800-526-2400 FAX 800-248-1460 www.lcn.ingersollrand.com 3/10 MOTOR GEARBOX MOTOR GEARBOX ASSEMBLY (W/O SWITCH), 9130-3454 Driving mechanism for operator. For full length unit. Switch not included. MOTOR GEARBOX ASSEMBLY, 9130-3454S Driving mechanism for operator. For 27” unit. Switch included. ACCESSORIES LCN 9130 SERIES 3454 3454S 3018 BRACKETS MOUNTING BRACKET, 9130-3018 Standard mounting bracket. SWITCH BRACKET – 29” CABLE, 9130-3351-1 Bracket used to locate switch at end of cover on full length unit. SWITCH BRACKET – 41” CABLE, 9130-3351-2 Bracket used to locate switch at end of cover on full length unit. SWITCH BRACKET – 51” CABLE, 9130-3351-3 Bracket used to locate switch at end of cover on full length unit. 3351-1 3351-2 3351-3 3462 CONTROL BOXES CONTROL BOX, (120v), 9130-3462 Electronic controlling device with power supply output and power boost feature for Benchmark. 72MC 72FC COVERS METAL COVER, 9130-72MC Standard, 27”,non-handed, extruded aluminum cover. FULL METAL COVER, 9130-72FC 36”, non-handed, extruded aluminum cover. 163 COVER INSERT 9130-163 Used to cover operator shaft opening. COVER END CAP INSERT, 9130-163-1 Used to cover switch hole opening. 334 COVER END CAP, 9130-334 Black plastic end caps. 163-1 61 LCN CLOSERS 121 W. RAILROAD AVE. P.O. BOX 100 PRINCETON, IL, USA 61356-0100 PHONE 800-526-2400 FAX 800-248-1460 www.lcn.ingersollrand.com 3/10 ACCESSORIES LCN 9130 SERIES TRACKS 3038 73 3034 STANDARD TRACK, 9130-3038 Standard, non-handed track. TRACK END CAP, 9130-73 Black plastic end caps. 3077T ROLLER, 9130-3034 Quiet low friction roller assembly. ARMS STANDARD ARM, 9130-3077T Non-handed arm. Track roller not included. 62 LCN CLOSERS 121 W. RAILROAD AVE. P.O. BOX 100 PRINCETON, IL, USA 61356-0100 PHONE 800-526-2400 FAX 800-248-1460 www.lcn.ingersollrand.com 3/10 TABLE OF SIZES Indicates recommended range of door width for operator. Note: For All Benchmark Series 30” minimum door width for 27” pull operator 36” minimum door width for full length pull operator DOOR WIDTH 30" 762mm HOW-TO-ORDER 9130 SERIES OPERATORS 1. SPECIFY FINISH. Standard Anodized Finish __________ Aluminum or Dark Bronze Operator will be shipped with: -STANDARD MOTOR GEARBOX (SF) -STANDARD CONTROL BOX (SC) -MOUNTING BRACKET -27” METAL COVER (CL27) -STANDARD ARM (3077T) -STANDARD TRACK w/TRACK ROLLER -WOOD and MACHINE SCREW PACK Unless options listed below are selected. 48" 1219mm 9131 Minimum Door Width ORDERING INFORMATION LCN 9130 SERIES OPERATOR OPTIONS COVER 36” Full Cover SPECIAL TEMPLATE ST-_________ 63 LCN CLOSERS 121 W. RAILROAD AVE. P.O. BOX 100 PRINCETON, IL, USA 61356-0100 PHONE 800-526-2400 FAX 800-248-1460 www.lcn.ingersollrand.com 3/10 Notes 64 LCN CLOSERS 121 W. RAILROAD AVE. P.O. BOX 100 PRINCETON, IL, USA 61356-0100 PHONE 800-526-2400 FAX 800-248-1460 www.lcn.ingersollrand.com 3/10 The 9140 BENCHMARK by LCN is an electrically powered low-energy operator. It provides easy access for people with disabilities, the elderly or the frail. Designed primarily for automatic opening applications that occasionally require manual opening. The BENCHMARK is a cost-effective solution for retrofitting an activated or manual door. SINGLE DOOR, SURFACE MOUNT (PUSH) OFFSET PIVOT/BUTT HINGE FEATURES LCN 9140 SERIES Push ‘N Go permits non-switch activation Microprocessor control box ensures reliability and maintains customer settings Power Boost allows for increased closing force near latch 9140 series operator is shipped with motor gearbox, control box, mounting plate, regular arm, metal cover, standard track, wood and machine screw pack. Actuators available separately, see page121. Single interior door, surface mounted. 9140 Series is fully compliant with UL 325 ADA compliant. and meets the provisions of ANSI A156.19. On/Off switch included as standard. The 9140 Series is UL listed for fire-rated Non-handed for either right or left swinging door. applications. The 9140 Series also meets 27” cover is standard, 36” optional. the provisions of the Americans with All potentiometers clearly labeled with their functions. Disabilities Act. LED lights indicate power to control box and motor gearbox. SU 65 FINISH COVER ARM FUNCTION ST AN D RE AR GU D ( SI L DO AR NG UB (DO LE) U L OF E E BL GR E) FS ES E S CE T PI NT VO (PU SH T ER PI ARM /PU VO LL T ) AR M HANDING RF A SU CE RF MO A UN SU CE T RF MO SI AC UN NG LE CO E T NC MO SIM DO U O E U CO ALE NT I LTA R NC D S ND NE CO EAL ING EPE OUS N NC ED LE P DO DEN AIR EA SI T LE MU OR PA D IR IN LTA DE NE HA O P ND EN US DE P NO ED NT AIR NPA HA IR ND ED ST AN CU DAR ST D A O CU M NO ST AN DIZ OM OD ED PA IZED IN M T ET AL MOUNTING LCN CLOSERS 121 W. RAILROAD AVE. P.O. BOX 100 PRINCETON, IL, USA 61356-0100 PHONE 800-526-2400 FAX 800-248-1460 www.lcn.ingersollrand.com 3/10 MOUNTING DETAILS LCN 9140 SERIES TOP JAMB SINGLE DOOR (OFFSET/BUTT HINGE, CENTER PIVOT, PULL, STANDARD COVER) MOUNTING 4 3/4" 121 MM 4 1/2" 114 MM 5 9/16" MIN. 141 MM 18 1/4" FROM EDGE OF DOOR OFFSET PIVOT OR BUTT HINGES OPERATOR 1 7/16" FROM TOP OF DOOR PUSH ARM ASS'Y 19 1/2" MAX. 495 MM 27" OPERATOR DOOR DOOR FRAME TOP JAMB SINGLE DOOR (OFFSET/BUTT HINGE, CENTER PIVOT, PULL, FULL COVER) MOUNTING MAXIMUM OPENING Template allows 90 degree power opening and 90 degree manual opening. 4 3/4" 121 MM 4 1/2" 114 MM 5 9/16" MIN. 141 MM 18 1/4" FROM EDGE OF DOOR OFFSET PIVOT OR BUTT HINGES OPERATOR PUSH ARM ASS'Y 1 7/16" FROM TOP OF DOOR 19 1/2" MAX. 495 MM FULL LENGTH OPERATOR DOOR DOOR FRAME Butt Hinges should not exceed 5” (127 mm) in width. Reveal for push installations should not exceed 6” (152 mm) for REGULAR ARM and 9 3/4” (248 mm) for LONG ARM. Head Frame minimum 2” (51 mm). Top Rail minimum 2” (51 mm). Flush ceiling installation requires 5 1/4” (133 mm) minimum. Opening and Closing Time are variable by adjustments to the electronic control module located on the operator assembly. Maximum hold open time adjustable up to approximately 30 seconds. Special Templates Customized installation templates or products may be available to solve unusual applications. Contact LCN for assistance. System Diagram see “AUTOMATIC OPERATORS” section pages 52-54 for typical system wiring and page 55 for electrical data. Please consult your local SSC representative or LCN for assistance with specific installations and material requirements. 66 LCN CLOSERS 121 W. RAILROAD AVE. P.O. BOX 100 PRINCETON, IL, USA 61356-0100 PHONE 800-526-2400 FAX 800-248-1460 www.lcn.ingersollrand.com 3/10 MOTOR GEARBOX MOTOR GEARBOX ASSEMBLY, 9140-3454S Driving mechanism for operator. For 27” unit. Switch included. 3454 3454S MOTOR GEARBOX ASSEMBLY (W/O SWITCH), 9140-3454 Driving mechanism for operator. For full length unit. Switch not included. ACCESSORIES LCN 9140 SERIES 3018 BRACKETS MOUNTING BRACKET, 9140-3018 Standard mounting bracket. SWITCH BRACKET – 29” CABLE, 9140-3351-1 Bracket used to locate switch at end of cover on full length unit. SWITCH BRACKET – 41” CABLE, 9140-3351-2 Bracket used to locate switch at end of cover on full length unit. 3351-1 3351-2 3351-3 SWITCH BRACKET – 51” CABLE, 9140-3351-3 Bracket used to locate switch at end of cover on full length unit. 3462 CONTROL BOXES CONTROL BOX, (120v), 9140-3462 Electronic controlling device with power supply output and power boost feature for Benchmark. 72MC 72FC COVERS METAL COVER, 9140-72MC Standard, 27”,non-handed, extruded aluminum cover. FULL METAL COVER, 9140-72FC 36” Full length, non-handed, extruded aluminum cover. 163 COVER INSERT 9140-163 Used to cover operator shaft opening. COVER END CAP INSERT, 9140-163-1 Used to cover switch hole opening. 334 COVER END CAP, 9140-334 Black plastic end caps. 67 LCN CLOSERS 121 W. RAILROAD AVE. P.O. BOX 100 PRINCETON, IL, USA 61356-0100 PHONE 800-526-2400 FAX 800-248-1460 www.lcn.ingersollrand.com 3/10 ACCESSORIES LCN 9140 SERIES ARMS 3077 3077L REGULAR ARM, 9140-3077 Non-handed arm. LONG PUSH ARM, 9140-3077L Non-handed long arm. 79LR 79 ROD & SHOE, 9140-79 Rod for use with regular arm. LONG ROD & SHOE, 9140-79LR Long rod for use with long arm. 68 LCN CLOSERS 121 W. RAILROAD AVE. P.O. BOX 100 PRINCETON, IL, USA 61356-0100 PHONE 800-526-2400 FAX 800-248-1460 www.lcn.ingersollrand.com 3/10 TABLE OF SIZES Indicates recommended range of door width for operator. Note: For All Benchmark Series 26” minimum door width for 27” push operator 36” minimum door width for full length push operator DOOR WIDTH 26" 762mm HOW-TO-ORDER 9140 SERIES OPERATORS 1. SPECIFY FINISH. Standard Anodized Finish __________ Aluminum or Dark Bronze Operator will be shipped with: -STANDARD MOTOR GEARBOX (SF) -STANDARD CONTROL BOX (SC) -MOUNTING BRACKET -27” METAL COVER (CL27) -REGULAR ARM (3077) -WOOD and MACHINE SCREW PACK Unless options listed below are selected. 48" 1219mm 9142 Minimum Door Width ORDERING INFORMATION LCN 9140 SERIES OPERATOR OPTIONS COVER 36” Full Cover ARM Long Arm (3077L) (reveals 6” to 9 3/4”) SPECIAL TEMPLATE ST-_________ 69 LCN CLOSERS 121 W. RAILROAD AVE. P.O. BOX 100 PRINCETON, IL, USA 61356-0100 PHONE 800-526-2400 FAX 800-248-1460 www.lcn.ingersollrand.com 3/10 Notes 70 LCN CLOSERS 121 W. RAILROAD AVE. P.O. BOX 100 PRINCETON, IL, USA 61356-0100 PHONE 800-526-2400 FAX 800-248-1460 www.lcn.ingersollrand.com 3/10 The 9150 BENCHMARK by LCN is an electrically powered low-energy operator. It provides easy access for people with disabilities, the elderly or the frail. Designed primarily for automatic opening applications that occasionally require manual opening. The BENCHMARK is a cost-effective solution for retrofitting an activated or manual door. PAIR DOOR, SURFACE MOUNT (PUSH) OFFSET PIVOT/BUTT HINGE FEATURES LCN 9150 SERIES Push ‘N Go permits non-switch activation Microprocessor control box ensures reliability and maintains customer settings Power Boost allows for increased closing force near latch 9150 series operator is shipped with motor gearboxes, control boxes, mounting plate, regular arms, metal cover, wood and machine screw packs. Actuators available separately, see page 121. Pair of interior doors, surface mounted. 9150 Series is fully compliant with UL 325 and meets the provisions of ANSI A156.19. The 9150 Series is UL listed for fire-rated applications. The 9150 Series also meets the provisions of the Americans with Disabilities Act. ADA compliant. On/Off switch included as standard. Non-handed for either right or left swinging door. 72” cover is standard, 96” is optional. All potentiometers clearly labeled with their functions. LED lights indicate power to control box and motor gearbox. SU 71 FINISH COVER ARM FUNCTION ST AN D RE AR GU D ( SI L DO AR NG ( UB DO LE) U L OF E E BL GR E) FS E E SS CE T PI NT VO (PU SH T ER PI ARM /PU VO LL T ) AR M HANDING RF A SU CE RF MO A UN SU CE T RF MO SI AC UN NG LE CO E T NC MO SIM DO EA UN UL OR T CO LE T NC D S IND ANE E O I E N P CO AL G EN US NC ED LE P D DO EN AIR EA SI T LE MU OR PA D IR IN LTA DE NE HA PE OU ND ND S NO ED EN PAI R NT PA HA I R ND ED ST AN CU DAR ST D A O CU M NO ST AN DIZ OM OD ED PA IZED IN M T ET AL MOUNTING LCN CLOSERS 121 W. RAILROAD AVE. P.O. BOX 100 PRINCETON, IL, USA 61356-0100 PHONE 800-526-2400 FAX 800-248-1460 www.lcn.ingersollrand.com 3/10 MOUNTING DETAILS LCN 9150 SERIES TOP JAMB, INDEPENDENT/SIMULTANEOU S PAIR (OFFSET PIVOT/BUTT HINGE, CENTER PIVOT, PUSH) MOUNTING 18 1/4" FROM EDGE OF DOOR 18 1/4" FROM EDGE OF DOOR OFFSET PIVOT OR BUTT HINGES OFFSET PIVOT OR BUTT HINGES PUSH ARM ASS'Y PUSH ARM ASS'Y FULL LENGTH OPERATOR Determined by wiring method during installation. 4 3/4" 121 MM 4 1/2" 114 MM 5 9/16" MIN. 141 MM OPERATOR 1 7/16" FROM TOP OF DOOR 19 1/2" MAX. 495 MM DOOR DOOR FRAME Butt Hinges should not exceed 5” (127 mm) in width. MAXIMUM OPENING Template allows 90 degree power opening and 90 degree manual opening. Reveal for push installations should not exceed 6” (152 mm) for REGULAR ARM and 9 3/4” (248 mm) for LONG ARM. Head Frame minimum 2” (51 mm). Top Rail minimum 2” (51 mm). Flush ceiling installation requires 5 1/4” (133 mm) minimum. Opening and Closing Time are variable by adjustments to the electronic control module located on the operator assembly. Maximum hold open time adjustable up to approximately 30 seconds. System Diagram see “AUTOMATIC OPERATORS” section pages 52-54 for typical system wiring and page 55 for electrical data. Special Templates Customized installation templates or products may be available to solve unusual applications. Contact LCN for assistance. Please consult your local SSC representative or LCN for assistance with specific installations and material requirements. 72 LCN CLOSERS 121 W. RAILROAD AVE. P.O. BOX 100 PRINCETON, IL, USA 61356-0100 PHONE 800-526-2400 FAX 800-248-1460 www.lcn.ingersollrand.com 3/10 MOTOR GEARBOX MOTOR GEARBOX ASSEMBLY, 9150-3454S Driving mechanism for operator. For 27” unit. Switch included. 3454 3454S MOTOR GEARBOX ASSEMBLY (W/O SWITCH), 9150-3454 Driving mechanism for operator. For full length unit. Switch not included. ACCESSORIES LCN 9150 SERIES 3018 BRACKETS MOUNTING BRACKET, 9150-3018 Standard mounting bracket. CONTROL BOXES CONTROL BOX, (120v), 9150-3462 Electronic controlling device with power supply output and power boost feature for Benchmark. 3462 COVERS METAL COVER, 9150-72MC Standard, 72”,non-handed, extruded aluminum cover. 72MC 72FC FULL METAL COVER, 9150-72FC 96” Full length, non-handed, extruded aluminum cover. COVER INSERT 9150-163 Used to cover operator shaft opening. 163 COVER END CAP INSERT, 9150-163-1 Used to cover switch hole opening. COVER END CAP, 9150-334 Black plastic end caps. 334 73 LCN CLOSERS 121 W. RAILROAD AVE. P.O. BOX 100 PRINCETON, IL, USA 61356-0100 PHONE 800-526-2400 FAX 800-248-1460 www.lcn.ingersollrand.com 3/10 ACCESSORIES LCN 9150 SERIES ARMS 3077 3077L REGULAR ARM, 9140-3077 Non-handed arm. LONG ARM, 9140-3077L Non-handed long arm. 79LR 79 ROD & SHOE, 9140-79 Rod for use with regular arm. LONG ROD & SHOE, 9140-79LR Long rod for use with long arm. 74 LCN CLOSERS 121 W. RAILROAD AVE. P.O. BOX 100 PRINCETON, IL, USA 61356-0100 PHONE 800-526-2400 FAX 800-248-1460 www.lcn.ingersollrand.com 3/10 TABLE OF SIZES Indicates recommended range of door width for operator. Note: For All Benchmark Series 52” minimum door width for full length push double door operator. DOOR WIDTH 52" 1321mm HOW-TO-ORDER 9150 SERIES OPERATORS 1. SPECIFY FINISH. Standard Anodized Finish __________ Aluminum or Dark Bronze Operator will be shipped with: -STANDARD MOTOR GEARBOX (2 ea) (SF) -STANDARD CONTROL BOX (2 ea.) (SC) -MOUNTING BRACKET (2 ea.) -72” METAL COVER (CL72) -REGULAR ARMS (2 ea.) (3077) -WOOD and MACHINE SCREW PACK Unless options listed below are selected. 96" 2438mm 9153 Minimum Door Width ORDERING INFORMATION LCN 9150 SERIES OPERATOR OPTIONS COVER 96” Full Length Cover ARM Long Arm (3077L) (reveals 6” to 9 3/4”) SPECIAL TEMPLATE ST-_________ 75 LCN CLOSERS 121 W. RAILROAD AVE. P.O. BOX 100 PRINCETON, IL, USA 61356-0100 PHONE 800-526-2400 FAX 800-248-1460 www.lcn.ingersollrand.com 3/10 Notes 76 LCN CLOSERS 121 W. RAILROAD AVE. P.O. BOX 100 PRINCETON, IL, USA 61356-0100 PHONE 800-526-2400 FAX 800-248-1460 www.lcn.ingersollrand.com 3/10 LCN SENIOR SWING UNIQUE FEATURES Digital Control Suite Provides exceptionally precise control of a large range of built- in functions combined with superior durability and performance. Visual indications and digital readouts of all control function settings and activity make adjustments easy, fast and accurate. Dual Independent Program Memories Each unit is pre-programmed to factory default settings. The installer can adjust the unit to meet the job site requirements. These field settings are locked into the computer’s memory. Any subsequent field adjustments replace the original field adjustments. The factory settings are always retained in memory and can be recalled to replace the field settings in just seconds, restoring the unit to its original programming. On-Board Diagnostics Sophisticated built-in diagnostics program monitors the system microprocessor, power supplies, drive systems and actuator and safety circuits. Reduces the time required to make sure the installation is complete and correct. On-Board Power Supply Provides 24V AC output or 24V DC output with rectifier to power card readers, manual actuators and other peripherals. Plug and Play Sensors Motion sensors and safety sensors feature a “plug and play” concept allowing fast and accurate wiring connections in only seconds. Electronic Circuit Protection High voltage (primary AC Input) is protected by replaceable fuse. Low voltage (secondary AC input) is protected by self-resetting fuses. Visual Function Indicators LED’s allow direct observation of these inputs while in visual function indicator mode: Key switch- set to Auto, OFF or HOLD Activate DMSS approach DMSS safety Bodyguard Power Boost Disable Programming Mode Allows tailoring the following functions to meet specific site conditions Opening Speed Backcheck Speed Backcheck Position Hold Open Delay Latch Position Auto Reverse- Closing Electric Lock Delay Power Boost Push N’ Go Alternate Action Safety Slow/Stop Slow Down Disable Push ‘N Go Allows pedestrians to walk up to the door and push it open as if it were a manual door. After the door is manually opened approximately 5 degrees, the Push ‘N Go feature takes over and continues to open the door – slowly and automatically to the full open position. With Push ‘N Go, the door will stay fully open from one to 32 seconds, depending on the time delay chosen. Auto Reverse A safety feature that reverses the direction of the door when it comes into contact with an object during either opening or closing. Safety Slow/Stops Function Once the door starts opening, any person or object entering the swing area will cause the door to go into a safety slow speed. This function can be set to allow for a short stop once a person or object is sensed. Power Boost Adds an additional latching force to ensure secure latching in severe wind or stack conditions. Power Boost is also ideal for overcoming slowing obstacles such as electric strikes. Provides approximately 25 lbs. of additional closing force. Microprocessor Control unit allows for quiet efficiency in operation. Combined with the all electromechanical unit, it eliminates unnecessary wear and prolongs the life of the unit. Electric Lock Delay Causes a 1 second delay between activate signal and door opening to allow time for most electric locks to disengage before operator opens door. 77 LCN CLOSERS 121 W. RAILROAD AVE. P.O. BOX 100 PRINCETON, IL, USA 61356-0100 PHONE 800-526-2400 FAX 800-248-1460 www.lcn.ingersollrand.com 3/10 Notes 78 LCN CLOSERS 121 W. RAILROAD AVE. P.O. BOX 100 PRINCETON, IL, USA 61356-0100 PHONE 800-526-2400 FAX 800-248-1460 www.lcn.ingersollrand.com 3/10 The 2810 SENIOR SWING by LCN is an ADA door operator that is a two-in-one swing door operator. SENIOR SWING operator when activated, opens doors automatically for wheelchair access, yet allows for manual operation for regular pedestrian traffic. OPERATOR MOUNTS SINGLE DOOR, OVERHEAD CONCEALED *CENTER PIVOT OFFSET PIVOT/BUTT HINGE FEATURES LCN 2810 SERIES Push ‘N Go permits non-switch activation Power Boost provides additional latching force Electromechanical unit with microprocessor control Meets International Building Code requirements and ANSI A156.19 UL approved for fire doors *CENTER PIVOT arm shown 2810 series operator is shipped with motor gearbox, control box, arm, bottom pivot, header, and mounting hardware. Actuators available separately, see page 121. Single door, overhead concealed. Meets ADA, requirements (power mode only). Handed product. 36” header length is standard. Specify length 33” to 49” max. Double door header available up to 98”, specify length 49” to 98” max. Consult factory regarding this option. Fixed or breakaway stop available with center pivot arm. Adjustable hold open period of 1 to 32 seconds in automatic or manual mode. ARM FUNCTION DA R GU D ( LA SIN DO R G UB (DO LE) LE UB OF EG LE FS ) ET RES S CE PI NT VO (PU SH T ER PI ARM /PU VO LL T ) AR M COVER RE SU 79 FINISH ST AN HANDING RF A SU CE RF MO A UN SU CE T RF MO SI AC UN NG LE CO E T NC MO SIM DO U O E U CO ALE NT I LTA R NC D S ND NE CO EAL ING EPE OUS N NC ED LE P DO DEN AIR EA SI T LE MU OR PA D IR IN LTA DE NE HA O P ND EN US DE P NO ED NT AIR NP HA AI R ND ED ST AN CU DAR ST D A O CU M NO ST AN DIZ OM OD ED PA IZED IN M T ET AL MOUNTING 2810 Series is fully compliant with UL 325 & UL 1998 and meets the provisions of ANSI A156.19. The 2810 Series is UL listed for fire-rated applications. The 2810 Series also meets the provisions of the Americans with Disabilities Act. LCN CLOSERS 121 W. RAILROAD AVE. P.O. BOX 100 PRINCETON, IL, USA 61356-0100 PHONE 800-526-2400 FAX 800-248-1460 www.lcn.ingersollrand.com 3/10 MOUNTING DETAILS LCN 2810 SERIES CONCEALED SINGLE DOOR (CENTER PIVOT, EMERGENCY BREAKOUT, PULL) MOUNTING 4 1/2" 114 MM 5 3/4" 146 MM EMERGENCY BREAKOUT Minimum header length 36”. SWING OPERATOR 3 3/4" 95 MM 1/8" 3 MM BREAKOUT STOP 1" 25 MM 3/16" 5 MM BREAKOUT DIRECTION INCOMING SWING DIRECTION 48" DOOR OPENING (MAX.) EXTERIOR Shown w/ 3 3/4” pivot CONCEALED SINGLE DOOR (CENTER PIVOT, FIXED STOP, PUSH) MOUNTING 4 1/2" 114 MM 5 3/4" 146 MM Minimum header length 36”. OUTGOING 1/8" 3 MM 3 3/4" 95 MM 1" 25 MM SWING OPERATOR FIXED STOP SWING DIRECTION 48" DOOR OPENING (MAX.) 3/16" 5 MM EXTERIOR Shown w/ 3 3/4” pivot MAXIMUM OPENING Template allows 90 degree power opening and 90 degree manual opening. Head Frame minimum 36” (L) x 5 3/4” (H) x 4 1/2” (W) ” (914 mm x 146 mm x 114 mm). Top Rail minimum 2” (51 mm). Opening & Closing Time are variable by adjustments to the electronic control box. Maximum hold open time adjustable up to approximately 32 seconds. Door Stop required for each door panel. System Diagram see “AUTOMATIC OPERATORS” section pages 52-54 for typical system wiring and page 55 for electrical data. Special Templates Customized installation templates or products may be available to solve unusual applications. Contact LCN for assistance. Please consult your local SSC representative or LCN for assistance with specific installations and material requirements. 80 LCN CLOSERS 121 W. RAILROAD AVE. P.O. BOX 100 PRINCETON, IL, USA 61356-0100 PHONE 800-526-2400 FAX 800-248-1460 www.lcn.ingersollrand.com 3/10 CONCEALED SINGLE DOOR (OFFSET PIVOT OR BUTT HINGE, SLIDE ARM, PUSH) MOUNTING 4 1/2" 114 MM EXTERIOR OUTGOING OFFSET PIVOTS or BUTT HINGES 3 3/4" 95 MM 5 3/4" 146 MM SWING OPERATOR SLIDE ARM ASS'Y SLIDE ARM ASS'Y WITH SLIDE BLOCK CONCEALING CHANNEL 1/8" 3 MM 11" SLIDE CHANNEL Minimum header length 33”. Installations require bottom pivot and two intermediate pivots. MOUNTING DETAILS LCN 2810 SERIES SWING DIRECTION 10 1/2" 257 MM CONCEALING CHANNEL DOOR FRAME DOOR Head Frame minimum 33” (L) x 5 3/4” (H) x 4 1/2” (W) ” (838 mm x 146 mm x 114 mm). Top Rail minimum 2” (51 mm). Opening & Closing Time are variable by adjustments to the electronic control box. Maximum hold open time adjustable up to approximately 32 seconds. MAXIMUM OPENING Template allows 90 degree power opening and 90 degree manual opening. Door Stop required for each door panel. System Diagram see “AUTOMATIC OPERATORS” section pages 52-54 for typical system wiring and page 55 for electrical data. Please consult your local SSC representative or LCN for assistance with specific installations and material requirements. 81 Special Templates Customized installation templates or products may be available to solve unusual applications. Contact LCN for assistance. LCN CLOSERS 121 W. RAILROAD AVE. P.O. BOX 100 PRINCETON, IL, USA 61356-0100 PHONE 800-526-2400 FAX 800-248-1460 www.lcn.ingersollrand.com 3/10 ACCESSORIES LCN 2810 SERIES MOTOR GEARBOX MOTOR GEARBOX (STANDARD FORCE) – SENIOR SWING, 2810-3454 Driving mechanism for operator. Provides 15lbs opening force. Handed. MOUNTING BRACKET MOUNTING BRACKET – 3 3/4”, 2810-375 Motor gearbox mounting bracket for 3 3/4" center, offset pivot, butt hinge installations. Front bracket. MOUNTING BRACKET – 2 3/4”, 2810-275 Motor gearbox mounting bracket for 2 3/4" center pivot installations. Front bracket. 3454 375 275 3018 3462 REAR MOUNT BRACKET, 2810-3018 Motor gearbox mounting bracket. Rear bracket. CONTROL BOXES CONTROL BOX- SENIOR SWING, 2810-3462 Electronic controlling device for Senior Swing. 3572HL HEADERS Header, 2810-3572HL Standard, mounting header. Single door, single operator. Specify length 30”to 49” maximum. Header, 2810-3572DD Standard, mounting header. Double door, single operator. Specify length 49”to 98” maximum. 3572DD END CAPS HEADER END CAPS, 2810-334 End cap with openings for wiring. 334 ARMS CENTER PIVOT ARM, 2810-3077CP (CENTER PIVOT INSTALLATIONS ONLY) Used with overhead concealed operators and center pivoted doors. 3077CP OFFSET PIVOT ARM, 2810-3077OP (OFFSET PIVOT OR BUTT HUNG INSTALLATIONS ONLY) Handed arm. Used with overhead concealed operators. 82 3077OP LCN CLOSERS 121 W. RAILROAD AVE. P.O. BOX 100 PRINCETON, IL, USA 61356-0100 PHONE 800-526-2400 FAX 800-248-1460 www.lcn.ingersollrand.com 3/10 CHANNELS CONCEALING CHANNEL, 2810-3072 Used to conceal arm in overhead concealed applications. For offset pivot and butt hinges installations. If ordering separately specify length and hand. SLIDE CHANNEL, 2810-168 (OFFSET PIVOT or BUTT HINGE INSTALLATIONS ONLY) Mounts in concealing channel. Allows arm to slide. 3072 168 ACCESSORIES LCN 2810 SERIES 384B INSTALLATION ACCESSORIES DOOR STOP BREAKAWAY, 2810-384B Allows in swinging door to swing out in case of emergency (Pull installations). For center pivoted installations only. 384F DOOR STOP FIXED, 2810-384F Prevents out swinging door from swinging in (Push installations). For center pivoted installations only. FILLER PLATE BLANK, 2810-12 Completes length of header box. 12 SPINDLE PLATE – 2 3/4”, 2810-11A Hides bottom of motor gearbox. Completes header box. Cutout allows for motor gearbox shaft. For 2 3/4" offset pivot/butt hinge installations. SPINDLE PLATE – 3 3/4”, 2810-11B Hides bottom of motor gearbox. Completes header box. Cutout allows for motor gearbox shaft. For 3 3/4" center pivot installations. 11A PIVOTS BOTTOM PIVOT ASSEMBLY, 2810-3107 Includes pivot body, pivot post and bottom pivot plate. For overhead concealed, center pivoted installations. Includes; 2810-107, 2810-110 and 2810-117. PIVOT BODY, 2810-107 Bottom pivot body for center pivoted installations. 11B 3107 PIVOT POST, 2810-110 Connects pivot body to bottom pivot plate for center pivoted installations. 107 110 117 BOTTOM PIVOT PLATE, 2810-117 Applied to floor for center pivoted installations. 83 LCN CLOSERS 121 W. RAILROAD AVE. P.O. BOX 100 PRINCETON, IL, USA 61356-0100 PHONE 800-526-2400 FAX 800-248-1460 www.lcn.ingersollrand.com 3/10 ORDERING INFORMATION LCN 2810 SERIES TABLE OF SIZES Indicates recommended range of door width for operator. Note: For all Senior Swing Series Single Door - Width per leaf 36” minimum, 48” maximum DOOR WIDTH 36" 914mm 48" 1219mm 2811 Minimum Door Width HOW-TO-ORDER 2810 SERIES OPERATORS 1. SELECT INSTALLATION TYPE 2811 2. ARMS Standard 3 3/4” (Offset pivoted) Arm (3077OP) Standard 2 3/4” (Center pivoted) Arm (3077CP) Standard 3 3/4” (Center pivoted) Arm (3077CP) 3. SPECIFY HAND RH LH 4. SPECIFY FINISH. Standard Anodized Finish _____________ Aluminum or Dark Bronze Operator will be shipped with: -STANDARD MOTOR GEARBOX (SF) -STANDARD CONTROL BOX (SC) -36” HEADER (36HL) -2 3/4” PIVOT POINT -WOOD and MACHINE SCREW PACK Unless options listed below are selected. OPERATOR OPTIONS HEADER HL__ (Specify length 33” to 49” offset pivot) HL__ (Specify length 36” to 49” center pivot) DD__ (Specify length 49” to 98”) STOPS* Positive Mechanical Stop (POS) Panic Breakaway Stop (BKY) *Available with Center Pivoted installations only. SPECIAL TEMPLATE ST-_________ 84 LCN CLOSERS 121 W. RAILROAD AVE. P.O. BOX 100 PRINCETON, IL, USA 61356-0100 PHONE 800-526-2400 FAX 800-248-1460 www.lcn.ingersollrand.com 3/10 The 2850 SENIOR SWING by LCN is an ADA door operator that is a two-inone swing door operator. SENIOR SWING operator when activated, opens doors automatically for wheelchair access, yet allows for manual operation for regular pedestrian traffic. OPERATOR MOUNTS SIMULTANEOUS PAIR, OVERHEAD CONCEALED *CENTER PIVOT OFFSET PIVOT/BUTT HINGE FEATURES LCN 2850 SERIES Push ‘N Go permits non-switch activation Power Boost provides additional latching force Electromechanical unit with microprocessor control Digital keypad for easy setup Meets International Building Code requirements and ANSI A156.19 UL approved for fire doors *CENTER PIVOT arm shown 2850 series operator is shipped with motor gearbox, control box, arm, bottom pivot, header, and mounting hardware. Actuators available separately, see page 121. Simultaneous pair, overhead concealed. Meets ADA, requirements (power mode only). Handed product. 72” header length is standard. Specify other length 60” to 98” max. Consult factory regarding this option. 2850 Series is fully compliant with UL 325 & UL 1998 and meets the provisions of ANSI A156.19. The 2850 Series is UL listed for fire-rated applications. The 2850 Series also meets the provisions of the Americans with Disabilities Act. Fixed or breakaway stop available (center pivot arm). Adjustable hold open period of 1 to 32 seconds in automatic or manual mode. SU 85 FINISH COVER ARM FUNCTION ST AN D RE AR GU D ( SI L DO AR NG UB (DO LE) U L OF E E BL GR E) FS ES E S CE T PI NT VO (PU S T ER AR H/P PI UL VO M L) T AR M HANDING RF A SU CE RF MO A UN SU CE T RF MO SI AC UN NG LE CO E T NC MO SIM DO EA UN UL OR T CO LE T NC D S IND ANE E I E N PE OU CO AL G S N NC ED LE P DO DEN AIR EA SI M T OR LE U P D AI IN LTA R DE NE HA PE OU ND ND S NO ED EN PAI R NT PA HA I R ND ED ST AN CU DAR ST D A O CU M NO A ST N DI OM OD ZED PA IZED IN M T ET AL MOUNTING LCN CLOSERS 121 W. RAILROAD AVE. P.O. BOX 100 PRINCETON, IL, USA 61356-0100 PHONE 800-526-2400 FAX 800-248-1460 www.lcn.ingersollrand.com 3/10 MOUNTING DETAILS LCN 2850 SERIES CONCEALED SIMULTANEOUS PAIR (CENTER PIVOT, EMERGENCY BREAK OUT, PULL) MOUNTING 4 1/2" 114 MM EXTERIOR EMERGENCY BREAKOUT EMERGENCY BREAKOUT Minimum header length 60” and 70” with stops. SWING OPERATOR 5 3/4" 146 MM 1/8" 3 MM 3 3/4" 95 MM 3 3/4" 95 MM 1" 25 MM BREAKOUT STOP 1" 25 MM INCOMING INCOMING BREAKOUT DIRECTION SWING DIRECTION 8'-0" DOOR OPENING (MAX.) EXTERIOR Shown w/ 3 3/4” pivot CONCEALED SIMULTANEOUS PAIR (CENTER PIVOT, FIXED STOP, PUSH) MOUNTING 4 1/2" 114 MM EXTERIOR Minimum header length 60” and 70” with stops. 5 3/4" 146 MM SWING OPERATOR 1/8" 3 MM OUTGOING OUTGOING 3 3/4" 95 MM 3 3/4" 95 MM FIXED STOP SWING DIRECTION 1" 25 MM 1" 25 MM 8'-0" DOOR OPENING (MAX.) EXTERIOR Shown w/ 3 3/4” pivot MAXIMUM OPENING Template allows 90 degree power opening and 90 degree manual opening. Head Frame minimum 60” (L) x 5 3/4” (H) x 4 1/2” (W) ” (1524 mm x 146 mm x 114 mm). Top Rail minimum 2” (51 mm). Opening & Closing Time are variable by adjustments to the electronic control box. Maximum hold open time adjustable up to approximately 32 seconds. Door Stop required for each door panel. System Diagram see “AUTOMATIC OPERATORS” section pages 52-54 for typical system wiring and page 55 for electrical data. Special Templates Customized installation templates or products may be available to solve unusual applications. Contact LCN for assistance. Please consult your local SSC representative or LCN for assistance with specific installations and material requirements. 86 LCN CLOSERS 121 W. RAILROAD AVE. P.O. BOX 100 PRINCETON, IL, USA 61356-0100 PHONE 800-526-2400 FAX 800-248-1460 www.lcn.ingersollrand.com 3/10 CONCEALED SIMULTANEOUS PAIR (OFFSET PIVOT/BUTT HINGE, PUSH) MOUNTING 4 1/2" 114 MM EXTERIOR 5 3/4" 146 MM OUTGOING OFFSET PIVOTS or BUTT HINGES 11" SLIDE CHANNEL 10 1/2" 267 MM Installations require bottom pivot and two intermediate pivots. SWING OPERATOR OUTGOING SLIDE ARM ASS'Y 1/8" 3 MM SLIDE ARM ASS'Y WITH SLIDE BLOCK CONCEALING CHANNEL SWING DIRECTION CONCEALING CHANNEL 3 3/4" 95 MM DOOR MOUNTING DETAILS LCN 2850 SERIES DOOR FRAME Head Frame minimum 60” (L) x 5 3/4” (H) x 4 1/2” (W) ” (1524 mm x 146 mm x 114 mm). Top Rail minimum 2” (51 mm). MAXIMUM OPENING Template allows 90 degree power opening and 90 degree manual opening. Opening & Closing Time are variable by adjustments to the electronic control box. Maximum hold open time adjustable up to approximately 32 seconds. Door Stop required for each door panel. System Diagram see “AUTOMATIC OPERATORS” section pages 52-54 for typical system wiring and page 55 for electrical data. Please consult your local SSC representative or LCN for assistance with specific installations and material requirements 87 Special Templates Customized installation templates or products may be available to solve unusual applications. Contact LCN for assistance. LCN CLOSERS 121 W. RAILROAD AVE. P.O. BOX 100 PRINCETON, IL, USA 61356-0100 PHONE 800-526-2400 FAX 800-248-1460 www.lcn.ingersollrand.com 3/10 ACCESSORIES LCN 2850 SERIES MOTOR GEARBOX MOTOR GEARBOX (STANDARD FORCE) – SENIOR SWING, 2850-3454 Driving mechanism for operator. Provides 15lbs opening force. Handed. MOUNTING BRACKET MOUNTING BRACKET – 3 3/4”, 2850-375 Motor gearbox mounting bracket for 3 3/4" center, offset pivot, butt hinge installations. Front bracket. MOUNTING BRACKET – 2 3/4”, 2850-275 Motor gearbox mounting bracket for 2 3/4" center pivot installations. Front bracket. 3454 375 275 3018 3462 REAR MOUNT BRACKET, 2850-3018 Motor gearbox mounting bracket. Rear bracket. CONTROL BOXES CONTROL BOX- SENIOR SWING, 2850-3462 Electronic controlling device for Senior Swing. 982 COMPANION CABLE, 2850-982 Cable that allows one control box to run two motor gearboxes. For use with Senior Swing. HEADERS HEADER, 2850-3572HL Standard, mounting header. Pair door, two operators. Specify length 60”to 98” maximum. 3572HL END CAPS HEADER END CAPS, 2850-334 End cap with openings for wiring. 334 ARMS CENTER PIVOT ARM, 2810-3077CP (CENTER PIVOT INSTALLATIONS ONLY) Used with overhead concealed operators and center pivoted doors. OFFSET PIVOT ARM, 2810-3077OP (OFFSET PIVOT OR BUTT HUNG INSTALLATIONS ONLY) Handed arm. Used with overhead concealed operators. 3077CP 88 3077OP LCN CLOSERS 121 W. RAILROAD AVE. P.O. BOX 100 PRINCETON, IL, USA 61356-0100 PHONE 800-526-2400 FAX 800-248-1460 www.lcn.ingersollrand.com 3/10 CHANNELS CONCEALING CHANNEL, 2850-3072 Used to conceal arm in overhead concealed applications. For offset pivot and butt hinges installations. If ordering separately specify length and hand. SLIDE CHANNEL, 2810-168 (OFFSET PIVOT or BUTT HINGE INSTALLATIONS ONLY) Mounts in concealing channel. Allows arm to slide. 3072 168 ACCESSORIES LCN 2850 SERIES 384B INSTALLATION ACCESSORIES DOOR STOP BREAKAWAY, 2850-384B Allows in swinging door to swing out in case of emergency (Pull installations). For center pivoted installations only. 384F DOOR STOP FIXED, 2850-384F Prevents out swinging door from swinging in (Push installations). For center pivoted installations only. FILLER PLATE BLANK, 2850-12 Completes length of header box. 12 SPINDLE PLATE – 2 3/4”, 2850-11A Hides bottom of motor gearbox. Completes header box. Cutout allows for motor gearbox shaft. For 2 3/4" offset pivot/butt hinge installations. SPINDLE PLATE – 3 3/4”, 2850-11B Hides bottom of motor gearbox. Completes header box. Cutout allows for motor gearbox shaft. For 3 3/4" center pivot installations. 11A PIVOTS BOTTOM PIVOT ASSEMBLY, 2850-3107 Includes pivot body, pivot post and bottom pivot plate. For overhead concealed, center pivoted installations. Includes; 2850-107, 2850-110 and 2850-117. PIVOT BODY, 2850-107 Bottom pivot body for center pivoted installations. 11B 3107 PIVOT POST, 2850-110 Connects pivot body to bottom pivot plate for center pivoted installations. 107 110 117 BOTTOM PIVOT PLATE, 2850-117 Applied to floor for center pivoted installations. 89 LCN CLOSERS 121 W. RAILROAD AVE. P.O. BOX 100 PRINCETON, IL, USA 61356-0100 PHONE 800-526-2400 FAX 800-248-1460 www.lcn.ingersollrand.com 3/10 ORDERING INFORMATION LCN 2850 SERIES TABLE OF SIZES Indicates recommended range of door width for operator. Note: For all Senior Swing Series Simultaneous Pair – Width per leaf 30” minimum to 48” maximum DOOR WIDTH 60" 1524mm 96" 2438mm 2853 Minimum Door Width HOW-TO-ORDER 2850 SERIES OPERATORS 1. SELECT INSTALLATION TYPE 2853 2. ARMS Standard 3 3/4” (Offset pivoted) Arm (3077OP) Standard 2 3/4” (Center pivoted) Arm (3077CP) Standard 3 3/4” (Center pivoted) Arm (3077CP) 3. SPECIFY FINISH. Standard Anodized Finish _____________ Aluminum or Dark Bronze Operator will be shipped with: -STANDARD MOTOR GEARBOX (SF) (1 LH & 1 RH) -STANDARD CONTROL BOX (SC) -COMPANION CABLE -72” HEADER (72HL) -2 3/4” PIVOT POINT -WOOD and MACHINE SCREW PACK Unless options listed below are selected. OPERATOR OPTIONS HEADER HL__ (Specify length 60” to 98”) STOPS* Pair Positive Mechanical Stop (POS) Pair Panic Breakaway Stop (BKY) *Available with Center Pivoted installations only. SPECIAL TEMPLATE ST-_________ 90 LCN CLOSERS 121 W. RAILROAD AVE. P.O. BOX 100 PRINCETON, IL, USA 61356-0100 PHONE 800-526-2400 FAX 800-248-1460 www.lcn.ingersollrand.com 3/10 The 2860 SENIOR SWING by LCN is an ADA door operator that is a two-inone swing door operator. SENIOR SWING operator when activated, opens doors automatically for wheelchair access, yet allows for manual operation for regular pedestrian traffic. OPERATOR MOUNTS INDEPENDENT PAIR, OVERHEAD CONCEALED *CENTER PIVOT OFFSET PIVOT/BUTT HINGE FEATURES LCN 2860 SERIES Push ‘N Go permits non-switch activation Power Boost provides additional latching force Electromechanical unit with microprocessor control Digital keypad for easy setup Meets International Building Code requirements and ANSI A156.19 UL approved for fire doors *CENTER PIVOT arm shown 2860 Series is fully compliant with UL 325 & UL 1998 and meets the provisions of ANSI A156.19. The 2860 Series is UL listed for fire-rated applications. The 2860 Series also meets the provisions of the Americans with Disabilities Act. 2860 series operator is shipped with motor gearbox, control boxes, bottom pivots, arms, header, and mounting hardware. Actuators available separately, see page 121. Independent pair of doors, overhead concealed. Meets ADA, requirements (power mode only). Handed product. 72” header length is standard. Specify other length 65” to 98” max. Consult factory regarding this option. Fixed or breakaway stop available (center pivot arm). Adjustable hold open period of 1 to 32 seconds in automatic or manual mode. DA R GU D ( LA SIN DO R G UB (DO LE) LE UB OF EG LE FS ) ET RES S CE PI NT VO (PU SH T ER PI ARM /PU VO LL T ) AR M ARM FUNCTION RE SU 91 COVER FINISH ST AN HANDING RF A SU CE RF MO A UN SU CE T RF MO SI AC UN NG LE CO E T NC MO SIM DO EA UN UL OR T CO LE T NC D S IND ANE CO EAL ING EPE OUS N NC ED LE P DO DEN AIR EA SI T LE MU OR PA D IR IN LTA DE NE HA PE OU ND ND S NO ED EN PAI R NT PA HA IR ND ED ST AN CU DAR ST D A O CU M NO ST AN DIZ OM OD ED PA IZED IN M T ET AL MOUNTING LCN CLOSERS 121 W. RAILROAD AVE. P.O. BOX 100 PRINCETON, IL, USA 61356-0100 PHONE 800-526-2400 FAX 800-248-1460 www.lcn.ingersollrand.com 3/10 MOUNTING DETAILS LCN 2860 SERIES CONCEALED INDEPENDENT PAIR (CENTER PIVOT, EMERGENCY BREAK OUT, PULL) MOUNTING 4 1/2" 114 MM EXTERIOR EMERGENCY BREAKOUT EMERGENCY BREAKOUT Minimum header length 65” and 70” with stops. SWING OPERATOR 5 3/4" 146 MM 1/8" 3 MM 3 3/4" 95 MM 3 3/4" 95 MM 1" 25 MM BREAKOUT STOP 1" 25 MM INCOMING INCOMING BREAKOUT DIRECTION SWING DIRECTION 8'-0" DOOR OPENING (MAX.) EXTERIOR Shown w/ 3 3/4” pivot CONCEALED INDEPENDENT PAIR (CENTER PIVOT, FIXED STOP, PUSH) MOUNTING 4 1/2" 114 MM EXTERIOR Minimum header length 65” and 70” with stops. SWING OPERATOR 5 3/4" 146 MM 1/8" 3 MM OUTGOING OUTGOING 3 3/4" 95 MM 3 3/4" 95 MM FIXED STOP SWING DIRECTION 1" 25 MM 1" 25 MM 8'-0" DOOR OPENING (MAX.) EXTERIOR Shown w/ 3 3/4” pivot MAXIMUM OPENING Template allows 90 degree power opening and 90 degree manual opening. Head Frame minimum 65” (L) x 5 3/4” (H) x 4 1/2” (W) ” (1651 mm x 146 mm x 114 mm). Top Rail minimum 2” (51 mm). Opening & Closing Time are variable by adjustments to the electronic control box. Maximum hold open time adjustable up to approximately 32 seconds. Door Stop required for each door panel. System Diagram see “AUTOMATIC OPERATORS” section pages 52-54 for typical system wiring and page 55 for electrical data. Special Templates Customized installation templates or products may be available to solve unusual applications. Contact LCN for assistance. Please consult your local SSC representative or LCN for assistance with specific installations and material requirements 92 LCN CLOSERS 121 W. RAILROAD AVE. P.O. BOX 100 PRINCETON, IL, USA 61356-0100 PHONE 800-526-2400 FAX 800-248-1460 www.lcn.ingersollrand.com 3/10 CONCEALED INDEPENDENT PAIR (OFFSET PIVOT/BUTT HINGE, PUSH) MOUNTING 4 1/2" 114 MM EXTERIOR 5 3/4" 146 MM OUTGOING OFFSET PIVOTS or BUTT HINGES 11" SLIDE CHANNEL 10 1/2" 267 MM Installations require bottom pivot and two intermediate pivots. SWING OPERATOR OUTGOING SLIDE ARM ASS'Y 1/8" 3 MM SLIDE ARM ASS'Y WITH SLIDE BLOCK CONCEALING CHANNEL SWING DIRECTION CONCEALING CHANNEL 3 3/4" 95 MM DOOR FRAME DOOR Head Frame minimum 65” (L) x 5 3/4” (H) x 4 1/2” (W) ” (1651 mm x 146 mm x 114 mm). Top Rail minimum 2” (51 mm). MOUNTING DETAILS LCN 2860 SERIES MAXIMUM OPENING Template allows 90 degree power opening and 90 degree manual opening. Opening & Closing Time are variable by adjustments to the electronic control box. Maximum hold open time adjustable up to approximately 32 seconds. Door Stop required for each door panel. System Diagram see “AUTOMATIC OPERATORS” section pages 52-54 for typical system wiring and page 55 for electrical data. Please consult your local SSC representative or LCN for assistance with specific installations and material requirements 93 Special Templates Customized installation templates or products may be available to solve unusual applications. Contact LCN for assistance. LCN CLOSERS 121 W. RAILROAD AVE. P.O. BOX 100 PRINCETON, IL, USA 61356-0100 PHONE 800-526-2400 FAX 800-248-1460 www.lcn.ingersollrand.com 3/10 ACCESSORIES LCN 2860 SERIES MOTOR GEARBOX MOTOR GEARBOX (STANDARD FORCE) – SENIOR SWING, 2860-3454 Driving mechanism for operator. Provides 15lbs opening force. Handed. 3454 MOUNTING BRACKET MOUNTING BRACKET – 3 3/4”, 2860-375 Motor gearbox mounting bracket for 3 3/4" center, offset pivot, butt hinge installations. Front bracket. 375 275 3018 MOUNTING BRACKET – 2 3/4”, 2860-275 Motor gearbox mounting bracket for 2 3/4" center pivot installations. Front bracket. 3462 REAR MOUNT BRACKET, 2860-3018 Motor gearbox mounting bracket. Rear bracket. CONTROL BOXES CONTROL BOX- SENIOR SWING, 2860-3462 Electronic controlling device for Senior Swing. 3572HL HEADERS HEADER, 2860-3572HL Standard, mounting header. Pair door, two operators. Specify length 65”to 98” maximum. END CAPS HEADER END CAPS, 2860-334 End cap with openings for wiring. 334 ARMS CENTER PIVOT ARM, 2810-3077CP (CENTER PIVOT INSTALLATIONS ONLY) Used with overhead concealed operators and center pivoted doors. 3077CP 3077OP OFFSET PIVOT ARM, 2810-3077OP (OFFSET PIVOT OR BUTT HUNG INSTALLATIONS ONLY) Handed arm. Used with overhead concealed operators. 94 LCN CLOSERS 121 W. RAILROAD AVE. P.O. BOX 100 PRINCETON, IL, USA 61356-0100 PHONE 800-526-2400 FAX 800-248-1460 www.lcn.ingersollrand.com 3/10 CHANNELS CONCEALING CHANNEL, 2860-3072 Used to conceal arm in overhead concealed applications. For offset pivot and butt hinges installations. If ordering separately specify length and hand. SLIDE CHANNEL, 2810-168 (OFFSET PIVOT or BUTT HINGE INSTALLATIONS ONLY) Mounts in concealing channel. Allows arm to slide. 3072 168 ACCESSORIES LCN 2860 SERIES 384B INSTALLATION ACCESSORIES DOOR STOP BREAKAWAY, 2860-384B Allows in swinging door to swing out in case of emergency (Pull installations). For center pivoted installations only. 384F DOOR STOP FIXED, 2860-384F Prevents out swinging door from swinging in (Push installations). For center pivoted installations only. FILLER PLATE BLANK, 2860-12 Completes length of header box. 12 SPINDLE PLATE – 2 3/4”, 2860-11A Hides bottom of motor gearbox. Completes header box. Cutout allows for motor gearbox shaft. For 2 3/4" offset pivot/butt hinge installations. SPINDLE PLATE – 3 3/4”, 2860-11B Hides bottom of motor gearbox. Completes header box. Cutout allows for motor gearbox shaft. For 3 3/4" center pivot installations. 11A PIVOTS BOTTOM PIVOT ASSEMBLY, 2860-3107 Includes pivot body, pivot post and bottom pivot plate. For overhead concealed, center pivoted installations. Includes; 2860-107, 2860-110 and 2860-117. PIVOT BODY, 2860-107 Bottom pivot body for center pivoted installations. 11B 3107 PIVOT POST, 2860-110 Connects pivot body to bottom pivot plate for center pivoted installations. 107 110 117 BOTTOM PIVOT PLATE, 2860-117 Applied to floor for center pivoted installations. 95 LCN CLOSERS 121 W. RAILROAD AVE. P.O. BOX 100 PRINCETON, IL, USA 61356-0100 PHONE 800-526-2400 FAX 800-248-1460 www.lcn.ingersollrand.com 3/10 ORDERING INFORMATION LCN 2860 SERIES TABLE OF SIZES Indicates recommended range of door width for operator. Note: For all Senior Swing Series Independent Pair – Width per leaf 32 1/2” minimum to 48” maximum DOOR WIDTH 65" 1651mm 96" 2438mm 2863 Minimum Door Width HOW-TO-ORDER 2860 SERIES OPERATORS 1. SELECT INSTALLATION TYPE 2863 2. ARMS Standard 3 3/4” (Offset pivoted) Arm (3077OP) Standard 2 3/4” (Center pivoted) Arm (3077CP) Standard 3 3/4” (Center pivoted) Arm (3077CP) 3. SPECIFY FINISH. Standard Anodized Finish _____________ Aluminum or Dark Bronze Operator will be shipped with: -STANDARD MOTOR GEARBOX (SF) (1 LH & 1 RH) -STANDARD CONTROL BOX (SC) (2 ea) -72” HEADER (72HL) -2 3/4” PIVOT POINT -WOOD and MACHINE SCREW PACK Unless options listed below are selected. OPERATOR OPTIONS HEADER HL__ (Specify length 65” to 98”) STOPS* Pair Positive Mechanical Stop (POS) Pair Panic Breakaway Stop (BKY) *Available with Center Pivoted installations only. SPECIAL TEMPLATE ST-_________ 96 LCN CLOSERS 121 W. RAILROAD AVE. P.O. BOX 100 PRINCETON, IL, USA 61356-0100 PHONE 800-526-2400 FAX 800-248-1460 www.lcn.ingersollrand.com 3/10 The 9530 SENIOR SWING by LCN is an ADA door operator that is a two-inone swing door operator. SENIOR SWING operators when activated, opens doors automatically for wheelchair access, yet allows for manual operation for regular pedestrian traffic. SINGLE DOOR, SURFACE MOUNT (PULL) OFFSET PIVOT/BUTT HINGE FEATURES LCN 9530 SERIES Push ‘N Go permits non-switch activation Power Boost provides additional latching force Electromechanical unit with microprocessor control Digital keypad for easy setup Meets International Building Code requirements and ANSI A156.19 UL approved for fire doors 9530 Series is fully compliant with UL 325 & UL 1998 and meets the provisions of ANSI A156.19. The 9530 Series is UL listed for fire-rated applications. The 9530 Series also meets the provisions of the Americans with Disabilities Act. 9530 series operator is shipped with motor gearbox, control box, standard arm, header, and mounting hardware. Actuators available separately, see pages 121. Single door, surface mounted. Meets ADA requirements (power mode only). Handed product. 36” header length is standard. Specify length 33” to 49” max. Double door header available up to 98”, specify other length 49” to 98” max. Consult factory regarding this option. Adjustable hold open period of 1 to 32 seconds in automatic or manual mode. DA R GU D ( LA SIN DO R G UB (DO LE) LE UB OF EG LE FS ) ET RES S CE PI NT VO (PU SH T ER PI ARM /PU VO LL T ) AR M ARM FUNCTION RE SU 97 COVER FINISH ST AN HANDING RF A SU CE RF MO A UN SU CE T RF MO SI AC UN NG LE CO E T NC MO SIM DO EA UN UL OR T CO LE T NC D S IND ANE CO EAL ING EPE OUS N NC ED LE P DO DEN AIR EA SI T LE MU OR PA D IR IN LTA DE NE HA PE OU ND ND S NO ED EN PAI R NT PA HA IR ND ED ST AN CU DAR ST D A O CU M NO ST AN DIZ OM OD ED PA IZED IN M T ET AL MOUNTING LCN CLOSERS 121 W. RAILROAD AVE. P.O. BOX 100 PRINCETON, IL, USA 61356-0100 PHONE 800-526-2400 FAX 800-248-1460 www.lcn.ingersollrand.com 3/10 MOUNTING DETAILS LCN 9530 SERIES TOP JAMB SINGLE DOOR (OFFSET PIVOT/BUTT HINGE, CENTER PIVOT, PULL) MOUNTING 4 1/2" 114 MM 48" DOOR OPENING (MAX.) 17 3/8" 11 1/2" PULL CHANEL 292 MM SWING OPERATOR PULL ARM ASS'Y LEFT HAND 6 3/4" 171 MM 2 3/4" 70 MM 1 15/16" 49 MM OFFSET PIVOT or BUTT HINGES 5 3/4" 146 MM SWING OPERATOR 1" 25 MM PULL ARM ASS'Y PULL CHANEL INCOMING SWING DIRECTION DOOR 1 3/4" 44 MM INTERIOR HOLLOW METAL FRAME Suggested Installation MAXIMUM OPENING Template allows 90 degree power opening and 90 degree manual opening. Butt Hinges should not exceed 5” (127 mm) in width. Reveal should not exceed 4” (102 mm). Head Frame minimum 1 3/4” (44 mm). Face frame 6 3/4” (171 mm) total operator clearance. Top Rail minimum 2 3/4” (70 mm). Opening & Closing Time are variable by adjustments to the electronic control box. Maximum hold open time adjustable up to approximately 32 seconds. Special Templates Customized installation templates or products may be available to solve unusual applications. Contact LCN for assistance. System Diagram see “AUTOMATIC OPERATORS” section pages 52-54 for typical system wiring and page 55 for electrical data. Please consult your local SSC representative or LCN for assistance with specific installations and material requirements. 98 LCN CLOSERS 121 W. RAILROAD AVE. P.O. BOX 100 PRINCETON, IL, USA 61356-0100 PHONE 800-526-2400 FAX 800-248-1460 www.lcn.ingersollrand.com 3/10 MOTOR GEARBOX MOTOR GEARBOX (STANDARD FORCE) – SENIOR SWING, 9530-3454 Driving mechanism for operator. Provides 15lbs opening force. Handed. MOUNTING BRACKET MOUNTING BRACKET – 2 3/4”, 9530-275 Motor gearbox mounting bracket for 2 3/4" offset pivot or butt hinge installations. Front bracket. ACCESSORIES LCN 9530 SERIES 3454 275 3018 344-1 REAR MOUNT BRACKET, 9530-3018 Motor gearbox mounting bracket. Rear bracket. 3462 ANGLED BRACKET, 9530-334-1 Mounting bracket for surface applications. CONTROL BOXES CONTROL BOX – SENIOR SWING, 9530-3462 Electronic controlling device for Senior Swing. 3572HL HEADERS Header, 9530-3572HL Standard, mounting header. Single door, single operator. Specify length 30”to 49” maximum. Header, 9530-3572DD Standard, mounting header. Double door, single operator. Specify length 49”to 98” maximum. 3572DD END CAPS HEADER END CAPS, 9530-334 End cap with openings for wiring. 334 334-2 END DRESS PLATE, 9530-334-2 Metal finish end cap. 99 LCN CLOSERS 121 W. RAILROAD AVE. P.O. BOX 100 PRINCETON, IL, USA 61356-0100 PHONE 800-526-2400 FAX 800-248-1460 www.lcn.ingersollrand.com 3/10 ACCESSORIES LCN 9530 SERIES ARMS 3077PLCM STANDARD ARM ASSEMBLY, 9530-3077PLCM Handed arm. STANDARD ARM, 9530-3077T Handed arm. Track roller not included. TRACKS TRACK 9530-3038 Standard non-handed track. 3077T TRACK END CAP 9530-73 Black plastic end caps. ROLLER, 9530-3034 Quiet low friction roller assembly. INSTALLATION ACCESSORIES 3038 SPINDLE PLATE – 2 3/4”, 9530-11A Hides bottom of motor gearbox. Completes header box. Cutout allows for motor gearbox shaft. For 2 3/4" offset pivot or butt hinge installations. 3034 73 FILLER PLATE BLANK, 9530-12 Completes length of header box. (Specify Length) 11A MOUNTING PLATE, 9530-18 Optional mounting plate for standard hollow metal door frames. Specify length 33” to 98” maximum. NOTE: The length of a universal 18 plate will need to be ordered 3 1/2” longer than the supplied header. 12 18 100 LCN CLOSERS 121 W. RAILROAD AVE. P.O. BOX 100 PRINCETON, IL, USA 61356-0100 PHONE 800-526-2400 FAX 800-248-1460 www.lcn.ingersollrand.com 3/10 TABLE OF SIZES Indicates recommended range of door width for operator. Note: For all Senior Swing Series Single Door - Width per leaf 36” minimum, 48” maximum DOOR WIDTH 36" 914mm 48" 1219mm HOW-TO-ORDER 9530 SERIES OPERATORS 1. SPECIFY HAND RH LH 2. SPECIFY FINISH. Standard Anodized Finish _____________ Aluminum or Dark Bronze Operator will be shipped with: -STANDARD MOTOR GEARBOX (SF) -STANDARD CONTROL BOX (SC) -36” HEADER (36HL) -STANDARD ARM (3077T) -2 3/4” PIVOT POINT -STANDARD TRACK w/TRACK ROLLER -MACHINE SCREW PACK Unless options listed below are selected. 9531 Minimum Door Width ORDERING INFORMATION LCN 9530 SERIES OPERATOR OPTIONS HEADER HL __ (Specify length 36” to 49”) DD__ (Specify length 49” to 98”) MOUNTING PLATE Plate, ____ (Specify Length 30” to 98”) SPECIAL TEMPLATE ST-_________ 101 LCN CLOSERS 121 W. RAILROAD AVE. P.O. BOX 100 PRINCETON, IL, USA 61356-0100 PHONE 800-526-2400 FAX 800-248-1460 www.lcn.ingersollrand.com 3/10 Notes 102 LCN CLOSERS 121 W. RAILROAD AVE. P.O. BOX 100 PRINCETON, IL, USA 61356-0100 PHONE 800-526-2400 FAX 800-248-1460 www.lcn.ingersollrand.com 3/10 The 9540 SENIOR SWING by LCN is an ADA door operator that is a two-inone swing door operator. SENIOR SWING operators when activated, opens doors automatically for wheelchair access, yet allows for manual operation for regular pedestrian traffic. SINGLE DOOR, SURFACE MOUNT (PUSH) OFFSET PIVOT/BUTT HINGE FEATURES LCN 9540 SERIES Push ‘N Go permits non-switch activation Power Boost provides additional latching force Electromechanical unit with microprocessor control Digital keypad for easy setup Meets International Building Code requirements and ANSI A156.19 UL approved for fire doors 9540 series operator is shipped with motor gearbox, control box, regular arm, header, and mounting hardware. Actuators available separately, see page 121. Single door, surface mounted. Meets ADA requirements (power mode only). Handed product. 36” header length is standard. Specify length 33” to 49” max. Double door header available up to 98”, specify other length 49” to 98” max. Consult factory regarding this option. 9540 Series is fully compliant with UL 325 & UL 1998 and meets the provisions of ANSI A156.19. The 9540 Series is UL listed for fire-rated applications. The 9540 Series also meets the provisions of the Americans with Disabilities Act. Adjustable hold open period of 1 to 32 seconds in automatic or manual mode. SU 103 FINISH COVER ARM FUNCTION ST AN D RE AR GU D ( SI L DO AR NG ( UB DO LE) U L OF E E BL GR E) FS ES E S CE T PI ( V NT OT PUS ER H/ A R PU PI VO M LL T ) AR M HANDING RF A SU CE RF MO A UN SU CE T RF MO SI AC UN NG LE CO E T NC MO SIM DO EA UN UL OR T CO LE T NC D S IND ANE E O I E N P CO AL G EN US NC ED LE P D DO EN AIR EA SI T LE MU OR PA D IR IN LTA DE NE HA PE OU ND ND S NO ED EN PAI R NT PA HA I R ND ED ST AN CU DAR ST D A O CU M NO ST AN DIZ OM OD ED PA IZED IN M T ET AL MOUNTING LCN CLOSERS 121 W. RAILROAD AVE. P.O. BOX 100 PRINCETON, IL, USA 61356-0100 PHONE 800-526-2400 FAX 800-248-1460 www.lcn.ingersollrand.com 3/10 TOP JAMB SINGLE DOOR (OFFSET PIVOT/BUTT HINGE, CENTER PIVOT, PUSH) MOUNTI 4 1/2" 114 MM SWING 5 3/4" 146 MM OPERATOR 6 3/4" 171 MM OUTGOING 1 7/16" From top of door PUSH ARM ASS'Y Consult factory for all balance door installations. OFFSET PIVOT or BUTT HINGES 2 3/4" 70 MM 17" From edge of door REVEAL MOUNTING DETAILS LCN 9540 SERIES 1" 25 MM SECONDARY LINK SWING OPERATOR SWING DIRECTION DOOR FRAME 48" DOOR OPENING (MAX.) DOOR EXTERIOR HOLLOW METAL FRAME Suggested Installation MAXIMUM OPENING Butt Hinges should not exceed 5” (127 mm) in width. Template allows 90 degree power opening and 90 degree manual opening. Reveal for push installations should not exceed 10” (254 mm) for REGULAR ARM and 20” (508 mm) for LONG ARM. Head Frame minimum 1 3/4” (44 mm). Face frame 6 3/4” (171 mm) total operator clearance. Top Rail minimum 2 3/4” (70 mm). Opening & Closing Time are variable by adjustments to the electronic control box. Maximum hold open time adjustable up to approximately 32 seconds. Special Templates Customized installation templates or products may be available to solve unusual applications. Contact LCN for assistance. System Diagram see “AUTOMATIC OPERATORS” section pages 52-54 for typical system wiring and page 55 for electrical data. Please consult your local SSC representative or LCN for assistance with specific installations and material requirements. 104 LCN CLOSERS 121 W. RAILROAD AVE. P.O. BOX 100 PRINCETON, IL, USA 61356-0100 PHONE 800-526-2400 FAX 800-248-1460 www.lcn.ingersollrand.com 3/10 MOTOR GEARBOX MOTOR GEARBOX (STANDARD FORCE) – SENIOR SWING, 9540-3454 Driving mechanism for operator. Provides 15lbs opening force. Handed. ACCESSORIES LCN 9540 SERIES 3454 MOUNTING BRACKET MOUNTING BRACKET – 2 3/4”, 9540-275 Motor gearbox mounting bracket for 2 3/4" offset pivot or butt hinge installations. Front bracket. 275 3018 344-1 REAR MOUNT BRACKET, 9540-3018 Motor gearbox mounting bracket. Rear bracket. ANGLED BRACKET, 9540-334-1 Mounting bracket for surface applications. 3462 CONTROL BOXES CONTROL BOX – SENIOR SWING, 9540-3462 Electronic controlling device for Senior Swing. HEADERS Header, 9540-3572HL Standard, mounting header. Single door, single operator. Specify length 30”to 49” maximum. Header, 9540-3572DD Standard, mounting header. Double door, single operator. Specify length 49”to 98” maximum. 3572HL 3572DD END CAPS HEADER END CAPS, 9540-334 End cap with openings for wiring. END DRESS PLATE, 9540-334-2 Metal finish end cap. 334 105 LCN CLOSERS 121 W. RAILROAD AVE. P.O. BOX 100 PRINCETON, IL, USA 61356-0100 334-2 PHONE 800-526-2400 FAX 800-248-1460 www.lcn.ingersollrand.com 3/10 ACCESSORIES LCN 9540 SERIES ARMS 3077 3077L REGULAR ARM ASSEMBLY, 9540-3077 Handed arm. REGULAR LONG ARM ASSEMBLY, 9540-3077L Handed arm. MAIN ARM, 9540 -77 Handed arm attaches to motor gearbox. LINKAGE ASSEMBLY – 15”, 9540-79 Threaded rod attaches to door. Extends from main arm. 77 LINKAGE ASSEMBLY – 32”, 9540-79LR Threaded long rod attaches to door. Extends from main arm. Used for reveal 10” to 20”. INSTALLATION ACCESSORIES SPINDLE PLATE – 2 3/4”, 9540-11A Hides bottom of motor gearbox. Completes header box. Cutout allows for motor gearbox shaft. For 2 3/4" offset pivot or butt hinge installations. 79 79LR FILLER PLATE BLANK, 9540-12 Completes length of header box. (Specify Length) 11A MOUNTING PLATE, 9540-18 Optional mounting plate for standard hollow metal door frames. Specify length 33” to 98” maximum. NOTE: The length of a universal 18 plate will need to be ordered 3 1/2” longer than the supplied header. 12 18 106 LCN CLOSERS 121 W. RAILROAD AVE. P.O. BOX 100 PRINCETON, IL, USA 61356-0100 PHONE 800-526-2400 FAX 800-248-1460 www.lcn.ingersollrand.com 3/10 TABLE OF SIZES Indicates recommended range of door width for operator. Note: For all Senior Swing Series Single Door - Width per leaf 36” minimum, 48” maximum DOOR WIDTH 36" 914mm 48" 1219mm HOW-TO-ORDER 9540 SERIES OPERATORS 1. SPECIFY HAND RH LH 2. SPECIFY FINISH. Standard Anodized Finish _____________ Aluminum or Dark Bronze Operator will be shipped with: -STANDARD MOTOR GEARBOX (SF) -STANDARD CONTROL BOX (SC) -36” HEADER (36HL) -REGULAR ARM (3077) -2 3/4” PIVOT POINT -WOOD and MACHINE SCREW PACK Unless options listed below are selected. 9542 Minimum Door Width ORDERING INFORMATION LCN 9540 SERIES OPERATOR OPTIONS HEADER HL __ (Specify length 36” to 49”) DD__ (Specify length 49” to 98”) MOUNTING PLATE Plate, ____ (Specify Length 30” to 98”) ARM Long Arm (3077L) FINISH SPECIAL TEMPLATE ST-_________ 107 LCN CLOSERS 121 W. RAILROAD AVE. P.O. BOX 100 PRINCETON, IL, USA 61356-0100 PHONE 800-526-2400 FAX 800-248-1460 www.lcn.ingersollrand.com 3/10 Notes 108 LCN CLOSERS 121 W. RAILROAD AVE. P.O. BOX 100 PRINCETON, IL, USA 61356-0100 PHONE 800-526-2400 FAX 800-248-1460 www.lcn.ingersollrand.com 3/10 The 9550 SENIOR SWING by LCN is an ADA door operator that is a two-inone swing door operator. SENIOR SWING operators when activated, opens doors automatically for wheelchair access, yet allows for manual operation for regular pedestrian traffic. OPERATOR MOUNTS SIMULTANEOUS PAIR, SURFACE MOUNT *PULL SIDE PUSH SIDE DOUBLE EGRESS FEATURES LCN 9550 SERIES Push ‘N Go permits non-switch activation Power Boost provides additional latching force Electromechanical unit with microprocessor control Digital keypad for easy setup Meets International Building Code requirements and ANSI A156.19 *PULL SIDE mount shown UL approved for fire doors 9550 series operator is shipped with motor gearboxes, control box, arms, header, and mounting hardware. Actuators available separately, see pages 121. Simultaneous pair, surface mounted. Meets ADA requirements (power mode only). Handed product. Pull, Push or Double Egress applications available. 72” header length is standard. Specify other length 60” to 98”. Consult factory regarding this option. 9550 Series is fully compliant with UL 325 & UL 1998 and meets the provisions of ANSI A156.19. The 9550 Series is UL listed for fire-rated applications. The 9550 Series also meets the provisions of the Americans with Disabilities Act. Adjustable hold open period of 1 to 32 seconds in automatic or manual mode. COVER ARM FUNCTION D RE AR GU D ( SI L DO AR NG UB (DO LE) U L OF E E BL GR E) FS ES E S CE T PI NT VO (PU SH T ER PI ARM /PU VO LL T ) AR M SU 109 FINISH ST AN HANDING RF A SU CE RF MO A UN SU CE T RF MO SI AC UN NG LE CO E T NC MO SIM DO EA UN UL OR T CO LE T NC D S IND ANE E O I E N P CO AL G EN US NC ED LE P D DO EN AIR EA SI T LE MU OR P D AI IN LTA R DE NE HA PE OU ND ND S NO ED EN PAI R NT PA HA I R ND ED ST AN CU DAR ST D A O CU M NO ST AN DIZ OM OD ED PA IZED IN M T ET AL MOUNTING LCN CLOSERS 121 W. RAILROAD AVE. P.O. BOX 100 PRINCETON, IL, USA 61356-0100 PHONE 800-526-2400 FAX 800-248-1460 www.lcn.ingersollrand.com 3/10 TOP JAMB SIMULTANEOUS PAIR (OFFSET PIVOT/BUTT HINGE, CENTER PIVOT, PUSH) MOUNTING 4 1/2" 114 MM OUTGOING 6 3/4" 171 MM OUTGOING SWING 5 3/4" OPERATOR 146 MM 1 7/16" From top of door PUSH ARM ASS'Y OFFSET PIVOT or BUTT HINGES REVEAL MOUNTING DETAILS LCN 9550 SERIES 17" From edge of door 1" 25 MM DOOR 8'-0" DOOR OPENING (MAX.) TOP JAMB SIMULTANEOUS PAIR (OFFSET PIVOT/BUTT HINGE, CENTER PIVOT, PULL) MOUNTING SWING DIRECTION SECONDARY LINK 2 3/4" 70 MM SWING OPERATOR DOOR FRAME EXTERIOR 4 1/2" 114 MM 8'-0" DOOR OPENING (MAX.) 11 1/2" 291 MM 17 3/8" 441 MM 2 3/4" 70 MM PULL CHANNEL SWING OPERATOR OFFSET PIVOT or BUTT HINGES PULL ARM ASS'Y 5 3/4" 6 3/4" 146 MM SWING 171 MM OPERATOR 1 15/16" 49 MM 1" 25 MM PULL ARM ASS'Y PULL CHANNEL INCOMING SWING DIRECTION INCOMING INTERIOR 1 3/4" 44 MM DOOR INTERIOR MAXIMUM OPENING Butt Hinges should not exceed 5” (127 mm) in width. Template allows 90 degree power opening and 90 degree manual opening. Reveal for push installations should not exceed 10” (254 mm) for REGULAR ARM and 20” (508 mm) for LONG ARM. Reveal for pull installations should not exceed 4” (102 mm). Reveal for double egress installations should not exceed 4” (102 mm). Head Frame minimum 1 3/4” (44 mm). Face frame 6 3/4” (171 mm) total operator clearance. Top Rail minimum 2 3/4” (70 mm). Special Templates Customized installation templates or products may be available to solve unusual applications. Contact LCN for assistance. Opening & Closing Time are variable by adjustments to the electronic control box. Maximum hold open time adjustable up to approximately 32 seconds. System Diagram see “AUTOMATIC OPERATORS” section pages 52-54 for typical system wiring and page 55 for electrical data. Please consult your local SSC representative or LCN for assistance with specific installations and material requirements. 110 LCN CLOSERS 121 W. RAILROAD AVE. P.O. BOX 100 PRINCETON, IL, USA 61356-0100 PHONE 800-526-2400 FAX 800-248-1460 www.lcn.ingersollrand.com 3/10 17" From edge of door PUSH ARM ASS'Y SWING OPERATOR 11 1/2" 17 3/8" PULL CHANNEL 292 MM 48" DOOR OPENING (MAX.) SWING OPERATOR BUTT HINGES 1" 25 MM 2 3/4" 70 MM 6 3/4" 171 MM PUSH ARM ASS'Y SECONDARY LINK DOOR FRAME SWING OPERATOR 1" 25 MM SWING DIRECTION DOOR PULL ARM ASS'Y PULL CHANNEL DOOR FRAME SWING DIRECTION DOOR Consult factory for all balance door installations. MOUNTING DETAILS SWING OPERATOR BUTT HINGES 5 3/4" 146 MM PULL ARM ASS'Y 1 15/16" FROM TOP OF DOOR 48" DOOR OPENING (MAX.) 2 3/4" 70 MM TOP JAMB SIMULTANEOUS PAIR (RH DOUBLE EGRESS) MOUNTING 4 1/2" 114 MM 5 3/4 " 146 MM 4 1/2" 114 MM 1 3/4" 44 MM 2 3/18" FROM BOTTOM OF DOOR STOP LCN 9550 SERIES INTERIOR HOLLOW METAL FRAME Suggested Installation Butt Hinges should not exceed 5” (127 mm) in width. MAXIMUM OPENING Reveal for push installations should not exceed 10” (254 mm) for REGULAR ARM and 20” (508 mm) for LONG ARM. Template allows 90 degree power opening and 90 degree manual opening. Reveal for pull installations should not exceed 4” (102 mm). Reveal for double egress installations should not exceed 4” (102 mm). Head Frame minimum 1 3/4” (44 mm). Face frame 6 3/4” (171 mm) total operator clearance. Top Rail minimum 2 3/4” (70 mm). Opening & Closing Time are variable by adjustments to the electronic control box. Maximum hold open time adjustable up to approximately 32 seconds. System Diagram see “AUTOMATIC OPERATORS” section pages 52-54 for typical system wiring and page 55 for electrical data. Please consult your local SSC representative or LCN for assistance with specific installations and material requirements. 111 Special Templates Customized installation templates or products may be available to solve unusual applications. Contact LCN for assistance. LCN CLOSERS 121 W. RAILROAD AVE. P.O. BOX 100 PRINCETON, IL, USA 61356-0100 PHONE 800-526-2400 FAX 800-248-1460 www.lcn.ingersollrand.com 3/10 ACCESSORIES LCN 9550 SERIES MOTOR GEARBOX MOTOR GEARBOX (STANDARD FORCE) – SENIOR SWING, 9550-3454 Driving mechanism for operator. Provides 15lbs opening force. Handed. 3454 MOUNTING BRACKETS MOUNTING BRACKET – 2 3/4”, 9550-275 Motor gearbox mounting bracket for 2 3/4" offset pivot or butt hinge installations. Front bracket. 275 3018 344-1 REAR MOUNT BRACKET, 9550-3018 Motor gearbox mounting bracket. Rear bracket. ANGLED BRACKET, 9550-334-1 Mounting bracket for surface applications. CONTROL BOXES 3462 CONTROL BOX – SENIOR SWING, 9550-3462 Electronic controlling device for Senior Swing. COMPANION CABLE, 9550-982 Cable that allows one control box to run two motor gear boxes. Companion cable. For use with Senior Swing. HEADERS 982 HEADER, 9550-3572HL Standard, mounting header. Pair door, two operators. Specify length 60”to 98” maximum. END CAPS HEADER ENDCAPS, 9550-334 End cap with openings for wiring. 3572HL END DRESS PLATE, 9550-334-2 Metal finish end cap. 334 112 LCN CLOSERS 121 W. RAILROAD AVE. P.O. BOX 100 PRINCETON, IL, USA 61356-0100 334-2 PHONE 800-526-2400 FAX 800-248-1460 www.lcn.ingersollrand.com 3/10 ARMS ACCESSORIES LCN 9550 SERIES 3077PLCM STANDARD ARM ASSEMBLY, 9550-3077PLCM Handed arm. REGULAR ARM ASSEMBLY, 9550-3077 Handed arm. REGULAR LONG ARM ASSEMBLY, 9550-3077L Handed arm. STANDARD ARM, 9550-3077T Handed arm. Track roller not included. 3077 3077L MAIN ARM, 9550 -77 Handed arm attaches to motor gearbox 3077T 77 LINKAGE ASSEMBLY – 15”, 9550-79 Threaded rod attaches to door. Extends from main arm. LINKAGE ASSEMBLY – 32”, 9550-79LR Threaded long rod attaches to door. Extends from main arm. Used for reveal 10” to 20”. 79 79LR TRACKS TRACK 9550-3038 Standard non-handed track. 3038 TRACK END CAP 9550-73 Black plastic end caps. 3034 ROLLER, 9550-3034 Quiet low friction roller assembly. 73 INSTALLATION ACCESSORIES SPINDLE PLATE – 2 3/4”, 9550-11A Hides bottom of motor gearbox. Completes header box. Cutout allows for motor gearbox shaft. For 2 3/4" offset pivot or butt hinge installations. 11A 12 FILLER PLATE BLANK, 9550-12 Completes length of header box. (Specify Length) MOUNTING PLATE, 9550-18 Optional mounting plate for standard hollow metal door frames. Specify length 33” to 98” maximum. NOTE: The length of a universal 18 plate will need to be ordered 3 1/2” longer than the supplied header. 113 18 LCN CLOSERS 121 W. RAILROAD AVE. P.O. BOX 100 PRINCETON, IL, USA 61356-0100 PHONE 800-526-2400 FAX 800-248-1460 www.lcn.ingersollrand.com 3/10 ORDERING INFORMATION LCN 9550 SERIES TABLE OF SIZES Indicates recommended range of door width for operator. Note: For All Senior Swing Series Simultaneous Pair – Width per leaf 30” minimum to 48” maximum DOOR WIDTH 60" 1524mm 96" 2438mm HOW-TO-ORDER 9550 SERIES OPERATORS 1. SPECIFY HAND RH LH 2. SPECIFY FINISH. Standard Anodized Finish __________ Aluminum or Dark Bronze Operator will be shipped with: -STANDARD MOTOR GEARBOX (SF) (2 ea) -STANDARD CONTROL BOX (SC) -72” METAL COVER (72HL) -REGULAR ARM (2 ea) -2 3/4” PIVOT POINT -MACHINE SCREW PACK 9553 Minimum Door Width OPERATOR OPTIONS HEADER HL__ (Specify length 60” to 98”) MOUNTING PLATE Plate, ____ (Specify Length 30” to 98”) ARM Standard Arm (2 ea) w/Standard Track (2 ea) Double Egress Includes Standard Arm w/Track (1 ea) & Regular Arm (1 ea) Long Arm (3077L) SPECIAL TEMPLATE ST-_________ 114 LCN CLOSERS 121 W. RAILROAD AVE. P.O. BOX 100 PRINCETON, IL, USA 61356-0100 PHONE 800-526-2400 FAX 800-248-1460 www.lcn.ingersollrand.com 3/10 The 9560 SENIOR SWING by LCN is an ADA door operator that is a two-inone swing door operator. SENIOR SWING operators when activated, opens doors automatically for wheelchair access, yet allows for manual operation for regular pedestrian traffic. OPERATOR MOUNTS INDEPENDENT PAIR, SURFACE MOUNT *PULL SIDE PUSH SIDE DOUBLE EGRESS FEATURES LCN 9560 SERIES Push ‘N Go permits non-switch activation Power Boost provides additional latching force Electromechanical unit with microprocessor control Digital keypad for easy setup Meets International Building Code requirements and ANSI A156.19 *PULL SIDE mount shown 9560 series operator is shipped with motor gearboxes, control boxes, arms, header, and mounting hardware. Actuators available separately, see page121. Independent pair, surface mounted. Meets ADA requirements (power mode only). Handed product. Pull, Push or Double Egress applications available. 72” header length is standard. Specify other length 60” to 98”. Consult factory regarding this option. UL approved for fire doors 9560 Series is fully compliant with UL 325 & UL 1998 and meets the provisions of ANSI A156.19. The 9560 Series is UL listed for fire-rated applications. The 9560 Series also meets the provisions of the Americans with Disabilities Act. Adjustable hold open period of 1 to 32 seconds in automatic or manual mode. SU 115 FINISH COVER ARM FUNCTION ST AN D RE AR GU D ( SI L DO AR NG LE ( D UB ) L OU OF E E BL E G FS RE ) E SS CE T PI NT VO (PU SH T ER PI ARM /PU VO LL T ) AR M HANDING RF A SU CE RF MO A UN SU CE T RF MO SI AC UN NG LE CO E T NC MO SIM DO U O E U CO ALE NT I LTA R NC D S ND NE CO EAL ING EPE OUS N NC ED LE P DO DEN AIR EA SI T LE MU OR PA D IR IN LTA DE NE HA O P ND EN US DE P NO ED NT AIR NP HA AI R ND ED ST AN CU DAR ST D A O CU M NO ST AN DIZ OM OD ED PA IZED IN M T ET AL MOUNTING LCN CLOSERS 121 W. RAILROAD AVE. P.O. BOX 100 PRINCETON, IL, USA 61356-0100 PHONE 800-526-2400 FAX 800-248-1460 www.lcn.ingersollrand.com 3/10 TOP JAMB INDEPENDENT PAIR (OFFSET PIVOT/BUTT HINGE, CENTER PIVOT, PUSH) MOUNTING 4 1/2" 114 MM OUTGOING 6 3/4" 171 MM OUTGOING SWING 5 3/4" OPERATOR 146 MM 1 7/16" From top of door PUSH ARM ASS'Y OFFSET PIVOT or BUTT HINGES REVEAL MOUNTING DETAILS LCN 9560 SERIES 17" From edge of door 1" 25 MM DOOR 8'-0" DOOR OPENING (MAX.) TOP JAMB INDEPENDENT PAIR (OFFSET PIVOT/BUTT HINGE, CENTER PIVOT, PULL) MOUNTING SWING DIRECTION SECONDARY LINK 2 3/4" 70 MM SWING OPERATOR DOOR FRAME EXTERIOR 4 1/2" 114 MM 8'-0" DOOR OPENING (MAX.) 11 1/2" 291 MM 17 3/8" 441 MM 2 3/4" 70 MM PULL CHANNEL SWING OPERATOR OFFSET PIVOT or BUTT HINGES PULL ARM ASS'Y 5 3/4" 6 3/4" 146 MM SWING 171 MM OPERATOR 1 15/16" 49 MM 1" 25 MM PULL ARM ASS'Y PULL CHANNEL INCOMING SWING DIRECTION INCOMING INTERIOR 1 3/4" 44 MM DOOR INTERIOR Butt Hinges should not exceed 5” (127 mm) in width. MAXIMUM OPENING Template allows 90 degree power opening and 90 degree manual opening. Reveal for push installations should not exceed 10” (254 mm) for REGULAR ARM and 20” (508 mm) for LONG ARM. Reveal for pull installations should not exceed 4” (102 mm). Reveal for double egress installations should not exceed 4” (102 mm). Head Frame minimum 1 3/4” (44 mm). Face frame 6 3/4” (171 mm) total operator clearance. Top Rail minimum 2 3/4” (70 mm). Special Templates Customized installation templates or products may be available to solve unusual applications. Contact LCN for assistance. Opening & Closing Time are variable by adjustments to the electronic control box. Maximum hold open time adjustable up to approximately 32 seconds. System Diagram see “AUTOMATIC OPERATORS” section pages 52-54 for typical system wiring and page 55 for electrical data. Please consult your local SSC representative or LCN for assistance with specific installations and material requirements. 116 LCN CLOSERS 121 W. RAILROAD AVE. P.O. BOX 100 PRINCETON, IL, USA 61356-0100 PHONE 800-526-2400 FAX 800-248-1460 www.lcn.ingersollrand.com 3/10 17" From edge of door PUSH ARM ASS'Y SWING OPERATOR 11 1/2" 17 3/8" PULL CHANNEL 292 MM 48" DOOR OPENING (MAX.) SWING OPERATOR BUTT HINGES 1" 25 MM 2 3/4" 70 MM 6 3/4" 171 MM PUSH ARM ASS'Y SECONDARY LINK DOOR FRAME SWING OPERATOR 1" 25 MM SWING DIRECTION DOOR PULL ARM ASS'Y PULL CHANNEL DOOR FRAME SWING DIRECTION Consult factory for all balance door installation. MOUNTING DETAILS SWING OPERATOR BUTT HINGES 5 3/4" 146 MM PULL ARM ASS'Y 1 15/16" FROM TOP OF DOOR 48" DOOR OPENING (MAX.) 2 3/4" 70 MM TOP JAMB INDEPENDENT PAIR (RH DOUBLE EGRESS) MOUNTING 4 1/2" 114 MM 5 3/4 " 146 MM 4 1/2" 114 MM 1 3/4" 44 MM 2 3/18" FROM BOTTOM OF DOOR STOP LCN 9560 SERIES DOOR INTERIOR HOLLOW METAL FRAME Suggested Installation Butt Hinges should not exceed 5” (127 mm) in width. MAXIMUM OPENING Reveal for push installations should not exceed 10” (254 mm) for REGULAR ARM and 20” (508 mm) for LONG ARM. Template allows 90 degree power opening and 90 degree manual opening. Reveal for pull installations should not exceed 4” (102 mm). Reveal for double egress installations should not exceed 4” (102 mm). Head Frame minimum 1 3/4” (44 mm). Face frame 6 3/4” (171 mm) total operator clearance. Top Rail minimum 2 3/4” (70 mm). Opening & Closing Time are variable by adjustments to the electronic control box. Maximum hold open time adjustable up to approximately 32 seconds. System Diagram see “AUTOMATIC OPERATORS” section pages 52-54 for typical system wiring and page 55 for electrical data. Please consult your local SSC representative or LCN for assistance with specific installations and material requirements. 117 Special Templates Customized installation templates or products may be available to solve unusual applications. Contact LCN for assistance. LCN CLOSERS 121 W. RAILROAD AVE. P.O. BOX 100 PRINCETON, IL, USA 61356-0100 PHONE 800-526-2400 FAX 800-248-1460 www.lcn.ingersollrand.com 3/10 ACCESSORIES LCN 9560 SERIES MOTOR GEARBOX MOTOR GEARBOX (STANDARD FORCE) –SENIOR SWING, 9560-3454 Driving mechanism for operator. Provides 15lbs opening force. Handed. 3454 MOUNTING BRACKETS MOUNTING BRACKET – 2 3/4”, 9560-275 Motor gearbox mounting bracket for 2 3/4" offset pivot or butt hinge installations. Front bracket. 275 3018 344-1 REAR MOUNT BRACKET, 9560-3018 Motor gearbox mounting bracket. Rear bracket. ANGLED BRACKET, 9560-334-1 Mounting bracket for surface applications. 3462 CONTROL BOXES CONTROL BOX – SENIOR SWING, 9560-3462 Electronic controlling device for Senior Swing HEADERS HEADER, 9560-3572HL Standard, mounting header. Pair door, two operators. Specify length 60”to 98” maximum. 3572HL END CAPS HEADER END CAPS, 9560-334 End cap with openings for wiring. 334 END DRESS PLATE, 9560-334-2 Metal finish end cap. 118 LCN CLOSERS 121 W. RAILROAD AVE. P.O. BOX 100 PRINCETON, IL, USA 61356-0100 334-2 PHONE 800-526-2400 FAX 800-248-1460 www.lcn.ingersollrand.com 3/10 ARMS ACCESSORIES LCN 9560 SERIES 3077PLCM STANDARD ARM ASSEMBLY, 9560-3077PLCM Handed arm. REGULAR ARM ASSEMBLY, 9560-3077 Handed arm. REGULAR LONG ARM ASSEMBLY, 9560-3077L Handed arm. STANDARD ARM, 9560-3077T Handed arm. Track roller not included. 3077 3077L MAIN ARM, 9560 -77 Handed arm attaches to motor gearbox 3077T 77 LINKAGE ASSEMBLY – 15”, 9560-79 Threaded rod attaches to door. Extends from main arm. LINKAGE ASSEMBLY – 32”, 9560-79LR Threaded long rod attaches to door. Extends from main arm. Used for reveal 10” to 20”. 79 79LR TRACKS TRACK 9560-3038 Standard non-handed track. 3038 TRACK END CAP 9560-73 Black plastic end caps. 3034 ROLLER, 9560-3034 Quiet low friction roller assembly. 73 INSTALLATION ACCESSORIES SPINDLE PLATE – 2 3/4”, 9560-11A Hides bottom of motor gearbox. Completes header box. Cutout allows for motor gearbox shaft. For 2 3/4" offset pivot or butt hinge installations. 11A 12 FILLER PLATE BLANK, 9560-12 Completes length of header box. (Specify Length) MOUNTING PLATE, 9560-18 Optional mounting plate for standard hollow metal door frames. Specify length 33” to 98” maximum. NOTE: The length of a universal 18 plate will need to be ordered 3 1/2” longer than the supplied header. 119 18 LCN CLOSERS 121 W. RAILROAD AVE. P.O. BOX 100 PRINCETON, IL, USA 61356-0100 PHONE 800-526-2400 FAX 800-248-1460 www.lcn.ingersollrand.com 3/10 ORDERING INFORMATION LCN 9560 SERIES TABLE OF SIZES Indicates recommended range of door width for operator. Note: For all Senior Swing Series Independent Pair – Width per leaf 30” minimum to 48” maximum DOOR WIDTH 60" 914mm 96" 1219mm HOW-TO-ORDER 9560 SERIES OPERATORS 1. SPECIFY HAND RH LH 2. SPECIFY FINISH. Standard Anodized Finish _____________ Aluminum or Dark Bronze Operator will be shipped with: -STANDARD MOTOR GEARBOX (SF) (2 ea) -STANDARD CONTROL BOX (SC) (2 ea) -72” METAL COVER (72HL) -REGULAR ARM (2 ea) -2 3/4” PIVOT POINT -MACHINE SCREW PACK Unless options listed below are selected. 9563 Minimum Door Width OPERATOR OPTIONS HEADER HL__ (Specify length 60” to 98”) MOUNTING PLATE Plate, ____ (Specify Length 30” to 98”) ARM Standard Arm (2 ea) w/Standard Track (2 ea) Double Egress Includes Standard Arm w/Track (1 ea) & Regular Arm (1 ea) Long Arm (3077L) SPECIAL TEMPLATE ST-_________ 120 LCN CLOSERS 121 W. RAILROAD AVE. P.O. BOX 100 PRINCETON, IL, USA 61356-0100 PHONE 800-526-2400 FAX 800-248-1460 www.lcn.ingersollrand.com 3/10
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Page Count : 66 XMP Toolkit : XMP toolkit 2.9.1-13, framework 1.6 About : dbaaddc1-8abf-11e0-0000-bd8e86f5c905 Producer : GPL Ghostscript 8.63 Modify Date : 2011:05:27 09:21:48-04:00 Create Date : 2011:05:27 09:21:48-04:00 Creator Tool : \376\377\000P\000D\000F\000C\000r\000e\000a\000t\000o\000r\000 \000V\000e\000r\000s\000i\000o\000n\000 \0000\000.\0009\000.\0006 Document ID : dbaaddc1-8abf-11e0-0000-bd8e86f5c905 Format : application/pdf Title : \376\377\000E\000l\000e\000c\000t\000r\000o\000m\000e\000c\000h\000a\000n\000i\000c\000a\000l\000 \000P\000o\000w\000e\000r\000e\000d\000 \000S\000y\000s\000t\000e\000m\000s\000 \000A\000u\000t\000o\000m\000a\000t\000i\000c\000 \000O\000p\000e\000r\000a\000t\000o\000r\000s\000.\000p\000d\000f Creator : \376\377\000a\000m\000s\000u\000t\000t\000o\000n Author : amsutton Subject :EXIF Metadata provided by EXIF.tools