LDL Technology 14119 TCU with TPMS transmitting at 433.92 MHz User Manual C3131320010

LDL Technology TCU with TPMS transmitting at 433.92 MHz C3131320010

User Manual

CONFIDENTIAL INFORMATIONThis document is the exclusive property of LDL Technology.No content may be transmitted or reproduced in any form without written permission.Mounting procedure TCU Ref : C3131320010Version : A1Diffusion : Internal ExternalStatus : Confidential Limited ExtendedMounting procedureTCUReference : C3131320010 Version A1Internal ApprovalAuthor Check ApproverName and Department D. LUCE (MD) S.BAIGET (SY) P. GABAUDAN (PM)Date 13/04/15 15/04/15 15/04/15SignatureCOMPANY NAME DATE SIGNATUREC3131320010-A1-TCU_Mounting_Specification.odt LDL Technology SAS – Toulouse – France 1/ 16Copyrights 2015✘✘
CONFIDENTIAL INFORMATIONThis document is the exclusive property of LDL Technology.No content may be transmitted or reproduced in any form without written permission.Mounting procedure TCU Ref : C3131320010Version : A1MODIFCATION LIST :Version Modification date Chapter / pages Comments AuthorA0 13/04/2015 All Creation D.LUCEA1 17/06/2015 §8 Modification of regulatory notices M.GUERINC3131320010-A1-TCU_Mounting_Specification.odt LDL Technology SAS – Toulouse – France 2/ 16Copyrights 2015
CONFIDENTIAL INFORMATIONThis document is the exclusive property of LDL Technology.No content may be transmitted or reproduced in any form without written permission.Mounting procedure TCU Ref : C3131320010Version : A1Chapter :1. PURPOSE .................................................................................................................................. 42. TCU PRODUCT DESCRIPTION. ............................................................................................... 42.1. Part Numbers ....................................................................................................................... 42.2. External Description ............................................................................................................. 43. MAIN FEATURES ...................................................................................................................... 63.1. Electronic Features .............................................................................................................. 63.2. Mechanical Features ........................................................................................................... 63.3. Connector Pin Out ............................................................................................................... 64. TCU MOUNTING INTERFACE. ................................................................................................. 75. TCU MOUNTING RECOMMENDATIONS ................................................................................. 76. TCU POWER SUPPLY CONNECTION ..................................................................................... 97. TCU LOCATING RECOMMENDATIONS ................................................................................ 118. FCC/IC Regulatory notices ....................................................................................................... 138.1. Modification statement: ...................................................................................................... 138.2. Interference statement: ...................................................................................................... 138.3. Radiation Exposure Statement: ......................................................................................... 138.4. FCC Class B digital device notice ..................................................................................... 149. APPENDIX ................................................................................................................................ 14C3131320010-A1-TCU_Mounting_Specification.odt LDL Technology SAS – Toulouse – France 3/ 16Copyrights 2015
CONFIDENTIAL INFORMATIONThis document is the exclusive property of LDL Technology.No content may be transmitted or reproduced in any form without written permission.Mounting procedure TCU Ref : C3131320010Version : A11. PURPOSEThis document is the Mounting procedure of the TCU.TCU is a part of a Tire Pressure Monitoring System.The Telematic Control Unit (TCU) collects information on the vehicle and transmits it over the GSM network to a back-end server. It can capture data from CAN, GPS and TPMS.2. TCU PRODUCT DESCRIPTION. 2.1. PART NUMBERSTCU Part Number Region Model13 132 0000 Europe Middle East Africa (EMEA) 13 12313 144 0000 Europe Middle East Africa (EMEA) 13 14414 119 0000 North America (NA) 14 11915 046 0000 North America (NA) 14 1192.2. EXTERNAL DESCRIPTIONPart Material CharacteristicsTCU all electronic parts -1 Housing PBT GF20 - UL94 V0 Black1 Cover PBT GF20 - UL94 V0 Black1 10 Ways FCI PBT GF20 - UL94 V0 Black8 Screws Steel C 1018 -3 Silent-blocks EPDM Black3 Spacers Stainless steel A2 -1 Nitto Vent NA (assembly) BlackC3131320010-A1-TCU_Mounting_Specification.odt LDL Technology SAS – Toulouse – France 4/ 16Copyrights 2015
CONFIDENTIAL INFORMATIONThis document is the exclusive property of LDL Technology.No content may be transmitted or reproduced in any form without written permission.Mounting procedure TCU Ref : C3131320010Version : A1C3131320010-A1-TCU_Mounting_Specification.odt LDL Technology SAS – Toulouse – France 5/ 16Copyrights 2015Nitto ventSpacerHousing10 Ways Delphi Connector APEX 150Silent blockscrewCoverscrew
CONFIDENTIAL INFORMATIONThis document is the exclusive property of LDL Technology.No content may be transmitted or reproduced in any form without written permission.Mounting procedure TCU Ref : C3131320010Version : A13. MAIN FEATURES3.1. ELECTRONIC FEATURESPower supply (5A fuse protected) 7 to 32 VOperating current 1 ATemperature operating range -40°C to 85°CStorage temperature range 0 to 30°CLegal RegulationsR&TTE (99/5/EC)FCC/ICPTCRBE markingAntennas (GSM, GPS and RF) Internal3.2. MECHANICAL FEATURESTotal Mass 256 gDimensions (L x W x H) 123 x 120 x 50 mmConnector (10 Ways) FCI - Delphi Connector APEX 150Tightness IP 68 & IP69KMounting LDL Brackets (see §4)Wiring LDL harnesses (see §6)3.3. CONNECTOR PIN OUTPin number Mnemonic Function1 CAN HI CAN High2 - Reserved3 CAN LO CAN Low4 BBM+ BBM positive5 IGN Ignition status (KL15)6 - Reserved7 VBAT Vehicle battery positive (KL30)8 - Reserved9 GND Vehicle battery negative (KL31)10 TEMP BBM temperatureC3131320010-A1-TCU_Mounting_Specification.odt LDL Technology SAS – Toulouse – France 6/ 16Copyrights 2015
CONFIDENTIAL INFORMATIONThis document is the exclusive property of LDL Technology.No content may be transmitted or reproduced in any form without written permission.Mounting procedure TCU Ref : C3131320010Version : A14. TCU MOUNTING INTERFACE. The TCU is mounted on a plane surface fixed on the vehicle frame. The TCU has 3 mounting points equipped with silent blocks. The TCU must be fixed on a support (available on demand). This support (TCU interface) is defined in the appendix.5. TCU MOUNTING RECOMMENDATIONSScrews (not provided by LDL) must be tightened @ 4,5 Nm +/-0,5 Nm. It's recommended to use an elastic washer (Belleville type) between screw head and silent block with spacer. Stainless steel is recommended.M6 bolts are recommended, the screw for a fixation on a base plate fixation in thickness 2mm must have a length equal or higher than 20mm.C3131320010-A1-TCU_Mounting_Specification.odt LDL Technology SAS – Toulouse – France 7/ 16Copyrights 2015
CONFIDENTIAL INFORMATIONThis document is the exclusive property of LDL Technology.No content may be transmitted or reproduced in any form without written permission.Mounting procedure TCU Ref : C3131320010Version : A1Nut M6InterfaceTCUWasherScrew M6TCU Assembled onto supportTCU AssemblyUniversal fixation kit can be provided by LDL. It consists of a base plate and an extension plate.A combination of these parts is able to fit all vehicle types. C3131320010-A1-TCU_Mounting_Specification.odt LDL Technology SAS – Toulouse – France 8/ 16Copyrights 2015
CONFIDENTIAL INFORMATIONThis document is the exclusive property of LDL Technology.No content may be transmitted or reproduced in any form without written permission.Mounting procedure TCU Ref : C3131320010Version : A1LDL TCU bracket combinationsTo link a base support to an extension support , 2 bolts are needed, type M6, length 16mm, with 2 M6 washers (1 standard type and 1 Belleville type).6. TCU POWER SUPPLY CONNECTION Cable must be fastened between 100mm and 200 mm away from its TCU starting point. Verify that no tension stress is applied onto the harness between TCU connector and the fixation point onto the vehicle chassis AND after connection of the harness connector onto the TCU connector.From the TCU connector base to the fixation point away TCU (100 to 200 mm), the harness cable must be in line as much as possible with the TCU connector terminal axis and not curvedover 30° see picture on next page below.The connector must be secured after clipping (move the red CPA (Connector Position Assurance) onto the harness connector toward the TCU connector)C3131320010-A1-TCU_Mounting_Specification.odt LDL Technology SAS – Toulouse – France 9/ 16Copyrights 2015
CONFIDENTIAL INFORMATIONThis document is the exclusive property of LDL Technology.No content may be transmitted or reproduced in any form without written permission.Mounting procedure TCU Ref : C3131320010Version : A1Cable management in the TCU neighborhood.Incorrect wiring will prevent the system from operating properly.TCU has to be connected to +12V or +24V through 5A fuse protection. TCU must be connected on Ignition (IGN).When TCU and ECU or EBS are connected to a same CAN network, they must share the same ground.LDL Technology can provide the wiring harness (see table below) :Nota : This cable has a minimum curvature radius about 80mm.Reference Description11 231 0000 Harness CAN (#1-Can) 11 232 0000 Harness (#1) 15 018 0000 Cable TCU CAN 1,2m - Wabco 15 017 0000 Cable TCU CAN 1,2m - EB+ gen3 - Haldex 15 016 0000 Cable TCU CAN Y 1,2m - EB+ gen2 - Haldex 15 015 0000 Cable TCU CAN 1,2m - EB+ gen2 - Haldex 15 014 0000 Cable TCU CAN 1,2m Deutsh 4 contacts 0462-201-16141 - Knorr 15 024 0000 Cable TCU CAN 1,2m – WABCO GIO5 C3131320010-A1-TCU_Mounting_Specification.odt LDL Technology SAS – Toulouse – France 10/ 16Copyrights 2015
CONFIDENTIAL INFORMATIONThis document is the exclusive property of LDL Technology.No content may be transmitted or reproduced in any form without written permission.Mounting procedure TCU Ref : C3131320010Version : A1 LOCKED POSITION OF THE CPAUNLOCKED POSITION OF THE CPATCU harness Delphi APEX 150 Clip holder, IP69K7. TCU LOCATING RECOMMENDATIONSThe TCU must be fixed horizontally and upside down (connector side facing the ground):The TCU must be free from any metallic shield in the direction of the connector side. The antenna should be cleared as possible to optimize RF communication and reduce areas ofnon-receipt.There must be a free area of minimum 5cm wide around the TCU in all directions. TCU must not be exposed to gritting.Each TCU must be at a central point between the wheels that it has to receive, and aligned on the vehicle axis. Distance between TCU and WUS must not exceed 3 meters. When trailer is equipped with an EBS, TCU bracket should be fixed to EBS bracket.C3131320010-A1-TCU_Mounting_Specification.odt LDL Technology SAS – Toulouse – France 11/ 16Copyrights 2015
CONFIDENTIAL INFORMATIONThis document is the exclusive property of LDL Technology.No content may be transmitted or reproduced in any form without written permission.Mounting procedure TCU Ref : C3131320010Version : A1MANDATORY TCU location:C3131320010-A1-TCU_Mounting_Specification.odt LDL Technology SAS – Toulouse – France 12/ 16Copyrights 2015Truck TCU Trailer TCUVehicle axisTCU TCUTCU-one point fixation sideIn green Vehicle axis
CONFIDENTIAL INFORMATIONThis document is the exclusive property of LDL Technology.No content may be transmitted or reproduced in any form without written permission.Mounting procedure TCU Ref : C3131320010Version : A18. FCC/IC REGULATORY NOTICES8.1. MODIFICATION STATEMENT:LDL Technology has not approved any changes or modifications to this device by the user. Anychanges or modifications could void the user’s authority to operate the equipment.LDL Technology n’approuve aucune modification apportée à l’appareil par l’utilisateur, quellequ’en soit la nature. Tout changement ou modification peuvent annuler le droit d’utilisation del’appareil par l’utilisateur.8.2. INTERFERENCE STATEMENT:This device complies with Part 15 of the FCC Rules and Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radioexempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil nedoit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillageradioélectrique subi, même si le brouillage est susceptible d'en compromettre lefonctionnement.8.3. RADIATION EXPOSURE STATEMENT:This device complies with FCC/IC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines and RSS 102 of ‐the IC radio frequency (RF) Exposure rules. The antenna should be installed and operated with minimum distance of 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.Le présent appareil est conforme à l'exposition aux radiations FCC / IC définies pour un environnement non contrôlé et répond aux directives d'exposition de la fréquence de la FCC radiofréquence (RF) et RSS 102 de la fréquence radio (RF) IC règles d'exposition. L'antenne ‐doit être installée de façon à garder une distance minimale de 20 centimètres entre la source de rayonnements et votre corps. L'émetteur ne doit pas être colocalisé ni fonctionner conjointement avec une autre antenne ou un autre émetteur.C3131320010-A1-TCU_Mounting_Specification.odt LDL Technology SAS – Toulouse – France 13/ 16Copyrights 2015
CONFIDENTIAL INFORMATIONThis document is the exclusive property of LDL Technology.No content may be transmitted or reproduced in any form without written permission.Mounting procedure TCU Ref : C3131320010Version : A18.4. FCC CLASS B DIGITAL DEVICE NOTICEThis equipment has been tested and found to comply with the limits for a Class B digital device,pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is noguarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:- Reorient or relocate the receiving antenna.- Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help.9. APPENDIXTCU interface dimension, see drawing belowC3131320010-A1-TCU_Mounting_Specification.odt LDL Technology SAS – Toulouse – France 14/ 16Copyrights 2015
CONFIDENTIAL INFORMATIONThis document is the exclusive property of LDL Technology.No content may be transmitted or reproduced in any form without written permission.Mounting procedure TCU Ref : C3131320010Version : A1Bracket in steel, thickness 2mm, with surface treatment to withstand at least 1500hr NSSC3131320010-A1-TCU_Mounting_Specification.odt LDL Technology SAS – Toulouse – France 15/ 16Copyrights 2015
CONFIDENTIAL INFORMATIONThis document is the exclusive property of LDL Technology.No content may be transmitted or reproduced in any form without written permission.Mounting procedure TCU Ref : C3131320010Version : A1Interface DrawingC3131320010-A1-TCU_Mounting_Specification.odt LDL Technology SAS – Toulouse – France 16/ 16Copyrights 2015

Navigation menu