| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 1450141 |
| Application ID | Q96IFiCYVKWF89o4SMGrtg== |
| Document Description | Users Manual-1 |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 246.38kB (3079770 bits) |
| Date Submitted | 2011-04-18 00:00:00 |
| Date Available | 2011-04-18 00:00:00 |
| Creation Date | 2011-04-13 09:40:55 |
| Producing Software | Acrobat Distiller 7.0 (Windows) |
| Document Lastmod | 2011-04-14 11:44:09 |
| Document Title | untitled |
19/22/26LE5300, 22/26LE5500
After connecting the cables as necessary,
install the CABLE HOLDER as shown
and bundle the cables.
FOR DESK-TYPE STAND
Install the CABLE MANAGEMENT CLIP
as shown.
PREPARATION
42/47/55LE7300
CABLE HOLDER
CABLE MANAGEMENT CLIP
32/37/42/47/55LE5300, 42/47/55LE530C
Secure the power cord with the CABLE
HOLDER on the TV back cover.
It will help prevent the power cable from
being removed by accident.
Connect the cables as necessary.
To connect additional equipment, see the
EXTERNAL EQUIPMENT SETUP section.
FOR WALL MOUNT
CABLE HOLDER
After connecting the cables as necessary,
install the CABLE HOLDER as shown
and bundle the cables.
Connect the cables as necessary.
To connect additional equipment, see the
EXTERNAL EQUIPMENT SETUP section.
Install CABLE HOLDER as shown and
bundle the cables.
CABLE HOLDER
CABLE HOLDER
31
PREPARATION
DESKTOP PEDESTAL INSTALLATION
ᯍ
Image shown may differ from your TV.
For proper ventilation, allow a clearance of 10.1 cm (4 inch) on all four sides from the wall.
PREPARATION
10.1 cm (4 inch)
10.1 cm (4 inch)
10.1 cm (4 inch)
10.1 cm (4 inch)
CAUTION
Ĺš Ensure adequate ventilation by following the clearance recommendations.
Ĺš Do not mount near or above any type of heat source.
SWIVEL STAND (Except 19/22LE5300, 22LE5500)
After installing the TV, you can adjust the TV set manually to the left or right direction by 20 Âş to suit
your viewing position.
KENSINGTON SECURITY SYSTEM
ᯍ
This feature is not available for all models.
- The TV is equipped with a Kensington Security System connector on the back panel. Connect the Kensington Security
System cable as shown below.
- For the detailed installation and use of the Kensington Security
System, refer to the userâs guide provided with the Kensington
Security System.
For further information, contact http://www.kensington.com,
the internet homepage of the Kensington company. Kensington
sells security systems for expensive electronic equipment such
as notebook PCs and LCD projectors.
NOTE: The Kensington Security System is an optional accessory.
32
ATTACHING THE TV TO A DESK
(For 32/42LD420, 32/37/42LD450, 37/42LD450C, 32/42LD520, 42LD630, 32LE5300,
42LD451C, 32/37/42LD452C, 32/42LD452B, 26LD352C)
ᯍ
Image shown may differ from your TV.
Stand
PREPARATION
The TV must be attached to a desk so it cannot be pulled in a forward/backward direction, potentially causing injury or damaging the product.
1-Screw
(provided as parts of the product)
Desk
For 37/42/47LD450C, 32/37/42/47LD452C, 32/42/47LD452B, 26LD352C
Stand
4-Screws
(not provided as parts of the product)
For 55LD520C
Desk
4-Screws
(not provided as parts of the product)
Ĺš Recommended screw size: M5 x L (*L: Table depth + 8~10 mm)
ex) Table depth: 15mm, Screw: M5 x 25
WARNING
Ĺš To prevent TV from falling over, the TV should be securely attached to the floor/wall per installation instructions. Tipping, shaking, or rocking the machine may cause injury.
33
PREPARATION
SECURING THE TV TO THE WALL TO PREVENT FALLING
WHEN THE TV IS USED ON A STAND
ᯍ
PREPARATION
ᯍ
You should purchase necessary components to prevent the TV from tipping over (when not using a
wall mount).
Image shown may differ from your TV.
We recommend that you set up the TV close to a wall so it cannot fall over if pushed backwards.
Additionally, we recommend that the TV be attached to a wall so it cannot be pulled in a forward
direction, potentially causing injury or damaging the product.
Caution: Please make sure that children donât climb on or hang from the TV.
ᯍ
Insert the eye-bolts (or TV brackets and bolts) to tighten the product to the wall as shown in the
picture.
* If your product has the bolts in the eye-bolts position before inserting the eye-bolts, loosen the
bolts.
* Insert the eye-bolts or TV brackets/bolts and tighten them securely in the upper holes.
Secure the wall brackets with the bolts (sold separately) to the wall. Match the height of the bracket
that is mounted on the wall to the holes in the product.
Ensure the eye-bolts or brackets are tightened securely.
ᯍ
Use a sturdy rope (sold separately) to tie the product. It is safer to tie the
rope so it becomes horizontal between the wall and the product.
! NOTE
Ĺš Use a platform or cabinet strong enough and large enough to support the size and weight of
the TV.
Ĺš To use the TV safely make sure that the height of the bracket on the wall and the one on the TV are
the same.
34
ᯍ
ᯍ
To prevent damage do not connect to the power outlet until all connections are made between the
devices.
Image shown may differ from your TV.
ANTENNA OR CABLE CONNECTION
PREPARATION
1. Antenna (Analog or Digital)
Wall Antenna Socket or Outdoor Antenna without a Cable Box
Connections.
For optimum picture quality, adjust antenna direction if needed.
Wall
Antenna
Socket
Outdoor
Antenna
(VHF, UHF)
Multi-family Dwellings/Apartments
(Connect to wall antenna socket)
ANTENNA/
CABLE IN
RF Coaxial Wire (75 Ί)
Single-family Dwellings /Houses
(Connect to wall jack for outdoor antenna)
Copper Wire
Be careful not to bend the copper wire
when connecting the antenna.
2. Cable
ANTENNA/
CABLE IN
Cable TV
Wall Jack
RF Coaxial Wire (75 Ί)
ᯍ
ᯍ
If the antenna needs to be split for two TVâs, install a 2-Way Signal Splitter.
For much more information about antennas visit our Knowledgebase at http://lgknowledgebase.
com. Search for antenna.
35
EXTERNAL
EXTERNALEQUIPMENT
EQUIPMENT
SETUP
SETUP
ᯍ
To prevent the equipment damage, never plug in any power cords until you have finished connecting all
equipment.
ᯍ
IThis part of EXTERNAL EQUIPMENT SETUP mainly use picture of for 26LE5300/26LE5500.
HD RECEIVER SETUP
This TV can receive digital over-the-air/digital cable signals without an external digital set-top box.
However, if you do receive digital signals from a digital set-top box or other digital external device.
Component Connection
EXTERNAL EQUIPMENT SETUP
1. How to connect
Connect the video outputs (Y, PB, PR) of the
digital set-top box to the COMPONENT IN
VIDEO or 1/2* jacks on the TV. Match the jack
colors (Y = green, PB = blue, and PR = red).
Connect the audio output of the digital set-top
box to the COMPONENT IN AUDIO or 1/2*
jacks on the TV.
VI)
PR
RS-232C IN
(CONTROL&SERVICE)
OPTICAL
AUDIO IN DIGITAL
RGB/DVI AUDIO OUT
Turn on the digital set-top box.
(Refer to the ownerâs manual for the digital settop box operation.)
2. How to use
ᯍ
PB
AV IN
VIDEO L(MONO) AUDIO R
GB IN (PC)
PB
VIDEO
PR
AUDIO
COMPONENT IN
ANTENNA/
CABLE IN
Select the Component or Component1/2* input
source on the TV using the INPUT button on the
remote control.
* Component2: For 32/37/42/47/55LE5300,
42/47/55LE7300, 42/47/55LE530C
ᯍ
Y, CB/PB, CR/PR
1280x720p
1920x1080i
1920x1080p
36
15.73
60.00
31.47
59.94
31.50
60.00
44.96
59.94
45.00
60.00
33.72
59.94
33.75
60.00
26.97
23.976
27.00
24.00
33.71
29.97
33.75
30.00
67.432
59.94
67.50
60.00
USB IN
59.94
IN 4
15.73
AV IN2
VIDEO / AUDIO
720x480p
Vertical
Frequency(Hz)
H/P
720x480i
Horizontal
Frequency(kHz)
COMPONENT IN2
Y PB PR / AUDIO
Resolution
For 32/37/42/47/55LE5300,
42/47/55LE7300, 42/47/55LE530C
PR
PB
HDMI Connection
No separate audio connection is necessary.
HDMI supports both audio and video.
DC-IN
(DVI)
RS-232C IN
(CONTROL&SERVICE)
OPTICAL
AUDIO IN DIGITAL
RGB/DVI AUDIO OUT
RGB IN (PC)
PB
VIDEO
PR
AUDIO
COMPONENT IN
2. How to use
ᯍ
AV IN
VIDEO L(MONO) AUDIO R
Turn on the digital set-top box.
(Refer to the ownerâs manual for the digital settop box.)
Select the HDMI1, HDMI2, HDMI3*, or HDMI4**
input source on the TV using the INPUT button
on the remote control.
* HDMI3: For 26LE5300, 26LE5500, 32/42/47/55LD520,
55LD520C, 42/47/55LD630
** HDMI4: For 32/37/42/47/55LE5300, 42/47/55LE7300,
42/47/55LE530C
ᯍ
HDMI OUTPUT
EXTERNAL EQUIPMENT SETUP
Connect the digital set-top box to HDMI/DVI IN
1, 2, 3*, or 4** jack on the TV.
/DVI IN
1. How to connect
! NOTE
Ĺš If an HDMI cable doesnât support High Speed HDMI,
it can cause flickers or no screen display. In this case
use the latest cables that support High Speed HDMI.
Ĺš HDMI Audio Supported Format: Dolby Digital (32 kHz, 44.1
kHz, 48 kHz), Linear PCM (32 kHz, 44.1 kHz, 48 kHz)
HDMI-DTV
Resolution
720x480p
1280x720p
1920x1080i
1920x1080p
Horizontal
Frequency(kHz)
Vertical
Frequency(Hz)
31.47
59.94
31.50
60.00
44.96
59.94
45.00
60.00
33.72
59.94
33.75
60.00
26.97
23.976
27.00
24.00
33.71
29.97
33.75
30.00
67.432
59.94
67.50
60.00
37
EXTERNAL EQUIPMENT SETUP
1. How to connect
DC-IN
EXTERNAL EQUIPMENT SETUP
/DVI IN
DVI to HDMI Connection
(DVI)
RS-232C IN
(CONTROL&SERVICE)
Connect the DVI output of the digital set-top
box to the HDMI/DVI IN 1 or 2* jack on the TV.
Connect the digital set-top box audio output to
the AUDIO IN (RGB/DVI) jack on the TV.
OPTICAL
AUDIO IN DIGITAL
RGB/DVI AUDIO OUT
AV IN
VIDEO1 L(MONO) AUDIO R
RGB IN (PC)
PB
VIDEO
PR
AUDIO
COMPONENT IN
2. How to use
ᯍ
ᯍ
Turn on the digital set-top box.
(Refer to the ownerâs manual for the digital settop box.)
Select the HDMI1 or HDMI2* input source on the
TV using the INPUT button on the remote control.
* HDMI2: For 32/42/47/55LD520, 55LD520C, 42/47/55LD630
AUDIO
! NOTE
Ĺš A DVI to HDMI cable or adapter is required for this connection. DVI doesn't support audio, so a separate audio
connection is necessary.
38
DVI OUTPUT
DVD SETUP
Component Connection
1. How to connect
Connect the audio outputs of the DVD to the
COMPONENT IN AUDIO or 1/2* jacks on the
TV.
(DVI)
PB
PR
RS-232C IN
ᯍ
ᯍ
OPTICAL
AUDIO IN DIGITAL
RGB/DVI AUDIO OUT
Turn on the DVD player, insert a DVD.
Select the Component or Component1/2* input
source on the TV using the INPUT button on the
remote control.
Refer to the DVD playerâs manual for operating
instructions.
(CONTROL&SERVICE)
2. How to use
ᯍ
EXTERNAL EQUIPMENT SETUP
Connect the video outputs (Y, PB, PR) of the
DVD to the COMPONENT IN VIDEO or 1/2*
jacks on the TV. Match the jack colors (Y =
green, PB = blue, and PR = red).
AV IN
VIDEO L(MONO) AUDIO R
RGB IN (PC)
PB
VIDEO
PR
AUDIO
ANTENNA/
CABLE IN
COMPONENT IN
* Component2: For 32/37/42/47/55LE5300,
42/47/55LE7300, 42/47/55LE530C
Component Input ports
To get better picture quality, connect a DVD
player to the component input ports as shown
below.
USB IN
PR
PB
PR
B-Y
R-Y
Cb
Cr
Pb
Pr
H/P
IN 4
PB
AV IN2
VIDEO / AUDIO
Video output ports
on DVD player
COMPONENT IN2
Y PB PR / AUDIO
Component ports on
the TV
For 32/37/42/47/55LE5300,
42/47/55LE7300, 42/47/55LE530C
PR
PB
39
EXTERNAL EQUIPMENT SETUP
Composite (RCA) Connection
1. How to connect
DVI)
EXTERNAL EQUIPMENT SETUP
ᯍ
ᯍ
RS-232C IN
(CONTROL&SERVICE)
Connect the AUDIO/VIDEO jacks between TV
and DVD. Match the jack colors (Video = yellow,
Audio Left = white, and Audio Right = red)
2. How to use
ᯍ
OPTICAL
AUDIO IN DIGITAL
RGB/DVI AUDIO OUT
AV IN
VIDEO L(MONO) AUDIO R
GB IN (PC)
Turn on the DVD player, insert a DVD.
Select the AV or AV1/2* input source on the TV
using the INPUT button on the remote control.
Refer to the DVD player's manual for operating
instructions.
PB
VIDEO
PR
AUDIO
ANTENNA/
CABLE IN
COMPONENT IN
* AV2: Except 19/22/26LE5300, 22/26LE5500
VIDEO
AUDIO
HDMI Connection
Connect the HDMI output of the DVD to the
HDMI/DVI IN 1, 2, 3*, or 4** jack on the TV.
DC-IN
/DVI IN
1. How to connect
(DVI)
No separate audio connection is necessary.
HDMI supports both audio and video.
RS-232C IN
(CONTROL&SERVICE)
OPTICAL
AUDIO IN DIGITAL
RGB/DVI AUDIO OUT
AV IN
VIDEO L(MONO) AUDIO R
RGB IN (PC)
2. How to use
Select the HDMI1, HDMI2, HDMI3*, or HDMI4** input
source on the TV using the INPUT button on the
remote control.
ᯍ Refer to the DVD player's manual for operating
instructions.
* HDMI3: For 26LE5300, 26LE5500, 32/42/47/55LD520,
55LD520C, 42/47/55LD630
** HDMI4: For 32/37/42/47/55LE5300, 42/47/55LE7300,
42/47/55LE530C
PB
VIDEO
PR
ᯍ
! NOTE
Ĺš If an HDMI cable doesnât support High Speed HDMI,
it can cause flickers or no screen display. In this case
use the latest cables that support High Speed HDMI.
Ĺš HDMI Audio Supported Format: Dolby Digital (32 kHz, 44.1
kHz, 48 kHz), Linear PCM (32 kHz, 44.1 kHz, 48 kHz)
40
AUDIO
COMPONENT IN
HDMI OUTPUT
VCR SETUP
Antenna Connection
1. How to connect
O) AUDIO R
Connect the RF antenna out socket
of the VCR to the ANTENNA/CABLE
IN socket on the TV.
AUDIO
ANTENNA/
CABLE IN
Connect the antenna cable to the RF
antenna in socket of the VCR.
ANT OUT
S-VIDEO
ANT IN
OUTPUT
SWITCH
VIDEO
AUDIO
Wall Jack
2. How to use
ᯍ
ᯍ
Set VCR output switch to 3 or 4 and
then tune TV to the same channel number.
Insert a video tape into the VCR and
press PLAY on the VCR (Refer to the
VCR ownerâs manual).
Antenna
EXTERNAL EQUIPMENT SETUP
Composite (RCA) Connection
1. How to connect
Connect the AUDIO/VIDEO jacks between TV
and VCR. Match the jack colors (Video = yellow,
Audio Left = white, and Audio Right = red)
VI)
2. How to use
ᯍ
ᯍ
Insert a video tape into the VCR and press PLAY
on the VCR. (Refer to the VCR ownerâs manual.)
Select the AV or AV1/2* input source on the TV
using the INPUT button on the remote control.
RS-232C IN
(CONTROL&SERVICE)
OPTICAL
AUDIO IN DIGITAL
RGB/DVI AUDIO OUT
AV IN
VIDEO L(MONO) AUDIO R
B IN (PC)
PB
VIDEO
PR
AUDIO
COMPONENT IN
ANTENNA/
CABLE IN
* AV2: Except 19/22/26LE5300, 22/26LE5500
! NOTE
ĹšIf you have a mono VCR, connect the audio cable
from the VCR to the AUDIO L(MONO) jack of the TV.
ANT IN
S-VIDEO
ANT OUT
OUTPUT
SWITCH
VIDEO
AUDIO
41
EXTERNAL EQUIPMENT SETUP
OTHER A/V SOURCE SETUP
EXTERNAL EQUIPMENT SETUP
Connect the AUDIO/VIDEO jacks
between TV and external equipment.
Match the jack colors.
(Video = yellow, Audio Left = white, and
Audio Right = red)
DC-IN
/DVI IN
1. How to connect
(DVI)
RS-232C IN
(CONTROL&SERVICE)
OPTICAL
AUDIO IN DIGITAL
RGB/DVI AUDIO OUT
AV IN
VIDEO L(MONO) AUDIO R
RGB IN (PC)
2. How to use
PB
VIDEO
PR
AUDIO
COMPONENT IN
ᯍ
ᯍ
Select the AV or AV1/2* input source on
the TV using the INPUT button on the
remote control.
Operate the corresponding external
equipment.
ANTENNA/
CABLE IN
* AV2: Except 19/22/26LE5300, 22/26LE5500
VIDEO
Video Game Set
Camcorder
42
USB CONNECTION
1. How to connect
2. How to use
After connecting the USB IN jack, you
Memory Key
IN 3
ᯍ
or
H/P
use the USB function. (Ĺšp.78)
EXTERNAL EQUIPMENT SETUP
Connect the USB device to the USB
IN jack on the side of TV.
USB IN
HEADPHONE SETUP
(Except 37/42/47LD450C, 32/37/42/47LD452C, 32/42/47LD452B, 26LD352C)
You can listen to the sound through the headphone.
Plug the headphone into the headphone socket.
To adjust the headphone volume,
press the VOL +/- button. If you
press the MUTE button, the sound
from the headphone is switched off.
H/P
1. How to connect
! NOTE
Ĺš AUDIO menu options are disabled when connecting a
headphone.
Ĺš When changing AV MODE with a headphone connected, the change is applied to video but not to audio.
Ĺš Optical Digital Audio Out is not available when connecting a headphone.
43
EXTERNAL EQUIPMENT SETUP
AUDIO OUT CONNECTION
1. How to connect
EXTERNAL EQUIPMENT SETUP
(DVI)
Connect one end of the optical cable to the
TV port of OPTICAL DIGITAL AUDIO OUT.
RS-232C IN
(CONTROL&SERVICE)
OPTICAL
AUDIO IN DIGITAL
RGB/DVI AUDIO OUT
AV IN
VIDEO L(MONO) AUDIO R
Connect the other end of the optical cable to
the digital audio input on the audio equipment.
RGB IN (PC)
PB
VIDEO
! NOTE
CAUTION
Ĺš Do not look into the optical output port. Looking at
the laser beam may damage your vision.
Ĺš Audio with ACP (Audio Copy Protection) function may
block digital audio output.
PR
AUDIO
COMPONENT IN
Set the âTV Speaker option - Offâ in the
AUDIO menu. (Ĺšp.119). See the external audio
equipment instruction manual for operation.
Ĺš When connecting with external audio equipment, such
as amplifiers or speakers, you can turn the TV speakers
off in the menu. (Ĺšp.119)
44
/DVI IN
Send the TVâs audio to external audio equipment via the Audio Output port.
If you want to enjoy digital broadcasting through 5.1-channel speakers, connect the OPTICAL DIGITAL
AUDIO OUT terminal on the back of TV to a Home Theater (or amp).
ANTENNA/
CABLE IN
PC SETUP
VGA (D-Sub 15 Pin) Connection
DC-IN
/DV
This TV provides Plug and Play capability, meaning that a PC adjusts automatically to the TVâs settings.
RS 232C IN
(DVI)
(CONTROL&SERVICE)
Connect the VGA output of the PC to the
RGB IN (PC) jack on the TV.
RGB IN (PC)
ᯍ
PB
VIDEO
PR
AUDIO
COMPONENT IN
Connect PC audio output to the AUDIO IN
(RGB/DVI) jack on the TV.
2. How to use
ᯍ
AV IN
VIDEO L(MONO) AUDIO R
RGB OUTPUT
AUDIO
Turn on the PC and the TV.
Select the RGB-PC input source on the TV using
the INPUT button on the remote control.
EXTERNAL EQUIPMENT SETUP
OPTICAL
AUDIO IN DIGITAL
RGB/DVI AUDIO OUT
1. How to connect
45
EXTERNAL EQUIPMENT SETUP
DVI to HDMI Connection
1. How to connect
Connect the DVI output of the PC to the
HDMI/DVI IN 1 or 2* jack on the TV.
Connect the PC audio output to the AUDIO IN
(RGB/DVI) jack on the TV.
2. How to use
ᯍ
ᯍ
Turn on the PC and the TV.
Select the HDMI1 or HDMI2* input source on the
TV using the INPUT button on the remote control.
DC-IN
/DVI IN
EXTERNAL EQUIPMENT SETUP
(DVI)
RS-232C IN
(CONTROL&SERVICE)
OPTICAL
AUDIO IN DIGITAL
RGB/DVI AUDIO OUT
RGB IN (PC)
PB
VIDEO
PR
AUDIO
COMPONENT IN
* HDMI2: For 32/42/47/55LD520, 55LD520C, 42/47/55LD630
AUDIO
46
AV IN
VIDEO L(MONO) AUDIO R
DVI OUTPUT
! NOTE
ĹšTo get the the best picture quality, adjust the PC graphics card to 1360 x 768 (19/22/26LE5300,
22/26LE5500, 32LD452C, 32LD452B, 26LD352C) or 1920 x 1080 (Other models).
ĹšDepending on the graphics card, DOS mode may not work if a HDMI to DVI Cable is in use.
ĹšAvoid keeping a fixed image on the screen for a long period of time. The fixed image may become
permanently imprinted on the screen.
ĹšThe synchronization input form for Horizontal and Vertical frequencies is separate.
ĹšDepending on the graphics card, some resolution settings may not allow the image to be positioned on the screen properly.
ĹšWhen selecting HDMI-PC, set the âInput Label - PCâ in the OPTION menu.
EXTERNAL EQUIPMENT SETUP
ĹšIn PC mode, there may be noise associated with the resolution, vertical pattern, contrast or brightness. If noise is present, change the PC output to another resolution, change the refresh rate to
another rate or adjust the brightness and contrast on the PICTURE menu until the picture is clear.
Supported Display Specifications (RGB-PC, HDMI-PC)
Resolution
Horizontal
Frequency(kHz)
Vertical
Frequency(Hz)
640x350
31.468
70.09
720x400
31.469
70.08
640x480
31.469
59.94
800x600
37.879
60.31
1024x768
48.363
60.00
1280x768
47.776
59.87
1360x768
47.712
60.015
1280x1024
63.981
60.02
1600x1200
75.00
60.00
Except 19/22/26LE5300,
22/26LE5500, 32LD452C,
32LD452B, 26LD352C
1920x1080
RGB-PC
66.587
59.934
Except 32/37/42/47/55LE5300,
42/47/55LE7300, 42/47/55LE530C
1920x1080
HDMI-PC
67.50
60.00
47
EXTERNAL EQUIPMENT SETUP
Screen Setup for PC mode
Selecting Resolution
EXTERNAL EQUIPMENT SETUP
You can choose the resolution in RGB-PC mode.
The Position, Phase, and Size can also be adjusted.
You can choose this option only when the PC resolution is set to 1024X768, 1280X768 or 1360X768.
3,&785(
áŻ0RYHáŻ(QWHU
6&5((1
5HVROXWLRQ
Ř%ULJKWQHVV
Ř6KDUSQHVV
Ř&RORU
Ř7LQW
Ř&RORU7HPS
Ř$GYDQFHG&RQWURO
Ř3LFWXUH5HVHW
$XWR&RQILJ
Ř 6FUHHQ 5*%3&
3RVLWLRQ
6L]H
ᯰ
áŻ
3KDVH
5HVHW
48
MENU
Select PICTURE.
ENTER
Select Screen (RGB-PC).
ENTER
Select Resolution.
ENTER
Select the desired resolution.
ENTER
áŻ0RYHá°3UHY
ᯥ[
Űł[
Űł[
Auto Configure
Automatically adjusts picture position and minimizes image instability. After adjustment, if the image
is still not correct, try using the manual settings or a different resolution or refresh rate on the PC.
áŻ0RYHá°3UHY
áŻ0RYHáŻ(QWHU
5HVROXWLRQ
Ř%ULJKWQHVV
Ř6KDUSQHVV
Ř&RORU
Ř7LQW
Ř&RORU7HPS
Ř$GYDQFHG&RQWURO
Ř3LFWXUH5HVHW
$XWR&RQILJ
Ř 6FUHHQ 5*%3&
3RVLWLRQ
6L]H
$XWR&RQILJ
+RPH8VH@ZKHQVHWWLQJ79XS
LQKRPH+RPH8VH@ZKHQVHWWLQJ79XS
LQKRPH6WRUH'HPR@IRULQVWRUHGVSOD\)RUXVH
LQKRPHVHOHFW>+RPH8VH@
Ř 6HW,'
Ř 0RGH6HWWLQJ
6WRUH'HPR
+RPH8VH
6WRUH'HPR
Ř 'HPR0RGH
2II
&ORVH
MENU
Select OPTION.
ENTER
Select Mode Setting.
ENTER
Select Store Demo.
ENTER
EXIT
74
áŻ0RYHáŻ(QWHU
Select On.
Return to TV viewing.
After a while, Demo Mode. starts.
If you want to stop the demo, press any
button (Except VOL +, - and MUTE button).
AV MODE
AV Mode toggles through preset Video and Audio settings.
AV MODE
&LQHPD
*DPH
6SRUW
Press the AV MODE button repeatedly to
select the desired source.
ᯍ
ENTER
ᯍ
ᯍ
ᯍ
ᯍ
ᯍ
If you select âCinemaâ in AV mode,
Cinema will be selected both for
âPICTURE menu - Picture Modeâ
and âAUDIO menu - Sound Modeâ
respectively.
If you select âOffâ in AV mode, the
âPicture Modeâ and âSound Modeâ
return to previous selected value.
Off: Disables the AV MODE.
Cinema: Optimizes video and audio
for watching movies.
Sport: Optimizes video and audio for
watching sports events.
Game: Optimizes video and audio for
playing games.
When playing a video game using
PlayStation or Xbox, it is recommended to use the Game mode.
When in Game mode, functions
related to picture quality will be optimized for playing games.
WATCHING TV / CHANNEL CONTROL
2II
75
WATCHING TV / CHANNEL CONTROL
SIMPLINK
SIMPLINK allows you to control and play other AV devices connected with HDMI cable without additional cables and settings. This TV may work with devices with HDMI-CEC support, but only devices
logo are fully supported.
with the
SIMPLINK can be turned on and off in the user menus.
áŻ(QWHUá°([LW
WATCHING TV / CHANNEL CONTROL
:DWFK79
Select On.
',6&
âŤŰ˝ÜâŹ
+'''9'5
9&5
âŤŰ˝ÜâŹ
ENTER
+'+7
+''5HFRUGHU
Select the desired device.
ENTER
6SHDNHU
âŤŰ˝ÜâŹ
Control connected AV devices.
796SHDNHU
76
Display SIMPLINK menu.
âŤÜâŹ2QâŤŰ˝âŹ
TV viewing: Switch to the previous TV
channel regardless of the current
mode.
DISC playback: Select and play discs.
When multiple discs are available, the
disc devices are conveniently displayed
at the bottom of the screen.
VCR playback: Control the connected
VCR.
HDD Recordings playback: Control
recordings stored in HDD.
Audio Out to Home Theater speaker/
Audio Out to TV: Select Home Theater
speaker or TV speaker for Audio Out.
áŻ(QWHUá°([LW
âŤÜâŹ2QâŤŰ˝âŹ
:DWFK79
',6&
âŤŰ˝ÜâŹ
ĹšWhen no device is connected (displayed in gray)
9&5
âŤŰ˝ÜâŹ
ĹšSelected Device
+'''9'5
+'+7
+''5HFRUGHU
6SHDNHU
âŤŰ˝ÜâŹ
796SHDNHU
ĹšWhen a device is conected (displayed in bright
color)
SIMPLINK Functions
ᯍ
ᯍ
Direct Play: After connecting AV devices to the TV, you can directly control the devices and play media
without additional settings.
Select AV device: Enables you to select one of the AV devices connected to the TV.
Disc playback: Control connected AV devices by pressing the á°á° !, ENTER, á°Ś, á°§, á°¨, á°Şand á°Š buttons.
ᯍ Power off all devices: When you power off the TV, all connected devices are turned off.
ᯍ Switch audio-out: Offers an easy way to switch audio-out.
ᯍ Sync Power on: When the equipment with Simplink function connected HDMI terminal starts to play,
The TV will automatically turn on.
Note: To operate SIMPLINK, an HDMI cable over Version 1.3 with *CEC function should be used. (*CEC:
Consumer Electronics Control).
(A device, which is connected to the TV through a HDMI cable but does not support SIMPLINK, does
not provide this function)
ᯍ
Ĺš Connect the HDMI/DVI IN or HDMI IN terminal of the TV to the rear terminal (HDMI terminal) of
the SIMPLINK device with the HDMI cable
Ĺš When you switch the Input source with the INPUT button on the remote control, the SIMPLINK
device will stop.
Ĺš When you select a device with home theater functionality, the sound output automatically switches
to the home theater speakers and the TV speakers are turned off.
Ĺš If a connected SIMPLINK home theater system doesnât play the audio from the TV, connect the
DIGITAL AUDIO OUT terminal on the back of the TV to the DIGITAL AUDIO IN terminal on the
back of the SIMPLINK device with an OPTICAL cable.
WATCHING TV / CHANNEL CONTROL
! NOTE
77
MY
MY MEDIA
MEDIA
CONNECTION METHOD
USB Connection
USB IN
1 Connect the USB device to the USB IN jack on the side of TV.
MY MEDIA
N3
Memory Key
Precautions when using the USB device
ĹšOnly a USB storage device is recognizable.
ĹšConnecting a USB storage device through a USB hub is not supported.
ĹšA USB storage device which uses its own driver may not be recognized.
ĹšThe recognition speed of a USB storage device may depend on each device.
ĹšPlease do not turn off the TV or unplug the USB device when the connected USB storage device
is working. When such device is suddenly separated or unplugged, the stored files or the USB
storage device may be damaged.
ĹšOnly use a USB storage device which has normal music files, image files, or movie files.
ĹšPlease use only a USB storage device which was formatted as a FAT 32 or NTFS file system provided with the Windows operating system. Others may not be recognized.
ĹšSome USB storage devices require a power adapter. The power adapter must be connected in
order to be seen by the TV.
ĹšIf a device is not recognized by the TV, try a different cable. Excessively long cables are not supported.
ĹšSome USB storage devices may not be supported or operate properly.
ĹšPlease backup important files because data on USB device could be damaged. Data management
is consumer's responsibility and as a result, the manufacturer does not cover data damage.
ĹšIf your USB memory device has multiple partitions, or if you use a USB multi-card reader, you can
use up to 4 partitions or USB memory devices.
ĹšIn case of USB storage devices formatted as NTFS, deletion is not supported.
ĹšFile alignment method of USB storage device is similar to Window XP and file names can be up
to 100 English characters.
ĹšThe recommended capacity is 1TB or less for a USB external hard disk and 32 GB or less for USB
memory.
ĹšIf a USB external hard disk with a âEnergy Savingâ function doesnât work, turn the hard disk off and
on again to make it work properly. Refer to the user manual of the USB external hard disk.
ĹšUSB storage devices below USB 2.0 are supported as well. But they may not work properly in the
movie list.
78
ENTRY MODE
The My Media menu will open automatically when you insert a USB drive. My Media can also be
accessed by choosing My Media in the user menu.
On USB device, you can not add a new folder or delete the existing folder.
0<0(',$
(]6LJQ79
0RYLH/LVW
3KRWR/LVW
0XVLF/LVW
([WUD&RQWHQWV
MENU
Select MY MEDIA.
ENTER
Select EzSign TV, Movie
List, Photo List or Music List
or Extra Contents.
ENTER
ᯍ
For 32/37/42/47LD452C
MY MEDIA
For 32/42/47LD452B Except 32/42/47LD420,
32/37/42/47LD450,
37/42/47LD450C,
32/42/47/55LD520,
55LD520C,
42/47/55LE530C,
42/47LD451C,
32/37/42/47LD452C,
32/42/47LD452B,
26LD352C
This TV can view JPG image files, HD DivX
files or play MP3 audio files.
When removing the USB device
Select the USB Device menu before
removing the USB device.
Q.MENU
ENTER
Select USB Device.
Select Eject.
79
MY MEDIA
MOVIE LIST
(Except 32/42/47LD420, 32/37/42/47LD450, 37/42/47LD450C, 32/42/47/55LD520, 55LD520C,
42/47/55LE530C, 42/47LD451C, 32/37/42/47LD452C, 32/42/47LD452B, 26LD352C)
The movie list is activated once a USB drive is detected. It is used when playing movie files on the TV.
It displays all of the video files it recognizes.
The On-Screen Display on your model may be slightly different.
MY MEDIA
Supported movie file
ᯍ Resolution: under 1920 pixel (width) x 1080 pixel (height)
ᯍ Frame Rate: under 30 frame/sec (1920x1080), under 60 frame/sec (1280x720)
ᯍ Max bitrate of playable video file: 20 Mbps (Mega bit per second)
ᯍ Bit rate : within 32 kbps to 320 kbps (MP3)
ᯍ Supported external subtitle format: *.smi/*.srt/*.sub (MicroDVD,Subviewer1.0/2.0)/*.ass/*.ssa/*.txt
(TMPlayer)/*.psb (PowerDivX)
ᯍ Supported Internal subtitle format: only, XSUB (It is the subtitle format used in DivX6 files)
Precautions when playing the video files
ĹšSome user-created subtitles may not work properly.
ĹšSome special characters are not supported in subtitles.
ĹšHTML tags are not supported in subtitles.
ĹšTime information in an external subtitle file should be arranged in ascending order to be played.
ĹšThe screen may suffer temporary interruptions (image stoppage, faster playback, etc.) when the
audio language is changed.
ĹšA damaged video file may not be played correctly, or some functions may not be usable.
ĹšVideo files produced with some encoders may not be played correctly.
ĹšIf the video and audio structure of recorded file is not interleaved, the file not playback properly.
ĹšVideo with resolution higher than maximum resolution supported for each frame, cannot be guaranteed for smooth playback.
ĹšVideo files other than the specified types and formats may not work properly.
ĹšThe movie file encoded by the GMC (Global Motion Compensation) is not supported.
ĹšOnly 250 Korean characters, 500 letters and 500 numbers are supported for each line of the
subtitle.
ĹšOnly 10000 sync blocks are supported within the subtitle file.
ĹšWe do not guarantee smooth playback of profiles encoded level 4.1 or higher in H.264/AVC.
ĹšDTS Audio codec is not supported.
ĹšA video file more than 30GB in file size is not supported for playback.
ĹšPlaying a video via a USB connection that doesnât support high speed may not work properly.
ĹšUSB storage devices below USB 2.0 are supported as well. But they may not work properly in the
movie list.
ĹšThe video file and its subtitle file must be located in the same folder.
At this time, a video file name and its subtitle file name must be identical for it to be displayed.
ĹšWhen you are watching a movie via the Movie List function, you can adjust the picture with the
ENERGY SAVING and AV MODE button on the remote control. User setup for each picture mode
is not supported.
80
Supported Video Formats
File
Video Decoder
Audio Codec
mpg, mpeg
MPEG1, MPEG2
MP2, MP3, Dolby Digital, LPCM
dat
MPEG1
MP2
ts, trp, tp
MPEG2, H.264, AVS, VC1
MP2, MP3, Dolby Digital, AAC,
HE-AAC
vob
MPEG1, 2
MP2, MP3, Dolby Digital, LPCM
mp4, mov
MPEG4,DivX 3.11, DivX 4.12, DivX 5.x,
DivX 6, Xvid 1.00, Xvid 1.01, Xvid 1.02,
Xvid 1.03, Xvid 1.10-beta1/2H.264
AAC, HE-AAC, MP3
mkv
H.264, MPEG-1,2,4
divx, avi
MPEG2, MPEG4, DivX 3.11, DivX 4,
DivX 5, DivX 6, Xvid 1.00, Xvid 1.01,
Xvid 1.02, Xvid 1.03, Xvid
1.10-beta1/2H.264
Max Resolution
Extension name
HE-AAC, LPCM
1920 x 1080 @ 30p
MP2, MP3, Dolby Digital,
LPCM,
ADPCM, AAC, HE-AAC
JPEG
LPCM, ADPCM
asf, wmv
VC1
WMA
flv
Sorenson H.263, H264
MP3, AAC
(avi, mp4, mkv)
MY MEDIA
Motion JPEG
MP2, MP3, Dolby Digital, AAC
(Only Motion JPEG
640x480@30p)
81
MY MEDIA
Screen Components
MENU
ENTER
Select MY MEDIA.
ENTER
Select Movie List.
MY MEDIA
Moves to upper level folder
Current page/Total pages
Corresponding buttons on the
remote control
Contents under the folder
focused on 1
Current page/total pages of
contents
3DJH
0RYLH/LVW
86%;7,&.
3DJH
'ULYH
0
0
0
0
0RRQ&KLOG'LY;$
áŻ0RYHáŻ3OD\áą3DJH&KDQJHáą
0DUN
áŻ7R3KRWR/LVW
áŻ&KDQJH1XPEHUV
áŻ0DUN0RGH
á°ż([LW
82
*5((1
Move to Photo List or Music List.
<(//2:
Change Numbers: Changes the number or thumbnails displayed at a time.
%/8(
Allows you to mark certain files.
EXIT
Return to TV viewing.
Movie Selection
3DJH
0RYLH/LVW
86%;7,&.
0
Select the target folder or drive.
3DJH
'ULYH
0
0
0
ENTER
0RRQ&KLOG'LY;$
ENTER
Select the desired
movie title.
Play the movie file.
áŻ0RYHáŻ3OD\áą3DJH&KDQJHáą
0DUN
áŻ&KDQJH1XPEHUV
áŻ0DUN0RGH
á°ż([LW
ᯍ
Use the CH (á°á°) button to navigate
in the movie page.
Mark Mode
3DJH
0RYLH/LVW
Select the target folder or
drive.
0DUN0RGH
3DJH
'ULYH
86%;7,&.
0
0
0
0
MY MEDIA
áŻ7R3KRWR/LVW
ENTER
Select the desired
movie title.
0RRQ&KLOG'LY;$
MARK
FAV
áŻ0RYHáŻ0DUNáą3DJH&KDQJHáą
0DUN
áŻ3OD\0DUNHG
5('
áŻ0DUN$OO
áŻ8QPDUN$OO
áŻ([LW0DUN0RGH
5('
á°ż([LW
Play the marked movie file.
It displays the current movie
status progress bar on the bottom of the screen.
Play Marked: Play the first selected file. Once
a movie finishes playing, the next selected
one will be played automatically.
ᯍ
*5((1
Mark All: Mark all files in the folder.
<(//2:
Unmark All: Deselect all marked files.
%/8(
Mark your desired movie file.
When one or more movie files are
marked, the marked movies will be
played in sequence.
Exit the Mark Mode.
83
MY MEDIA
Using the Movie List Function
&KRRVHRSWLRQV
6HW9LGHR3OD\
6HW9LGHR
6HW$XGLR
&ORVH
áŻáŻ
á°Ś
á°§
MY MEDIA
á°Ś
á°¨
á°Ş
á°Š
á°
áą2SWLRQ
á°+LGH
á°ż([LW
! NOTE
Q.MENU
Show the Option menu.
ENTER
Select Set Video Play., Set Video., or
Set Audio.
Using the remote control
Ĺš Option values changed in the Movie List
does not affect Photo List and Music
List.
Ĺš Option values changed in Photo List and
Music List are changed likewise in Photo
List and Music List, but not in the Movie
List.
Ĺš When replaying a video file after stopping, you can play from where it stopped
automatically.
Ĺš If you select âYesâ when playing the
same file after the video file has been
stopped, it will restart where it stopped
previously.
Ĺš If continuous series files exist within the
folder, the next file will automatically be
played. But, this excludes cases when
the Repeat function of Movie List Option
is turned âOnâ (Refer to page 85) or
when set as Marked Play.
Return to TV viewing.
EXIT
Select the required speed: x2, x4, x8, x16, x32 (backward/forward).
Pauses the media player.
If no buttons are pressed on the remote control for 10 minutes after pausing, the
TV returns to the playback state.
Displays a slow motion.
Move to a specific frame forward or backward while playing a video. A cursor indicating the position can be viewed on the screen. It may not work properly for
some movie files.
Return to normal playback.
BACK
or
ENERGY
SAVING
RETURN
Hide the menu on screen. To see the menu again, press ENTER button to display.
Press the ENERGY SAVING button repeatedly to increase the brightness of your
screen (Refer to p. 104).
AV MODE
Press the AV MODE button repeatedly to select the desired source (Refer to p. 75).
84
Set Video Play Menu Options
6HW9LGHR3OD\
âŤÜâŹ
)XOO
âŤŰ˝âŹ
$XGLR/DQJXDJH
âŤÜâŹ
âŤŰ˝âŹ
6XEWLWOH
âŤÜâŹ
2Q
âŤŰ˝âŹ
Ř/DQJXDJH
âŤÜâŹ
8QNQRZ
âŤŰ˝âŹ
Ř&RGH3DJH
âŤÜâŹ
'HIDXOW
âŤŰ˝âŹ
Ř6\QF
âŤÜâŹ
âŤŰ˝âŹ
Ř3RVLWLRQ
âŤÜâŹ
âŤŰ˝âŹ
Ř6L]H
âŤÜâŹ
1RUPDO
âŤŰ˝âŹ
5HSHDW
âŤÜâŹ
2II
âŤŰ˝âŹ
MY MEDIA
3LFWXUH6L]H
á°3UHYLRXV
Select Picture Size, Audio Language,
Subtitle, or Repeat.
ᯍ
ᯍ
Make appropriate adjustments.
ᯍ
Code Page
Subtitle Language Group
Supported Language
Latin1
English, Spanish, French
Korean
English, Korean
ᯍ
ᯍ
ᯍ
ᯍ
ᯍ
ᯍ
Picture Size: Selects your desired
picture format for videos.
Audio Language: Changes the
Language Group of the audio for
video files.
Subtitle Language: The subtitles can
be turned on or off. If there are two
or more subtitles, you can select one
of them.
Language: Activated for SMI subtitles
and can select the language within
the subtitle.
Code Page: Subtitle font selection.
When set to default, same font as
general menu will be used.
Sync: When the video is not synchronized with the captions, it can be
adjusted by 0.5 second.
Position: Move the location of the
subtitles.
Size: Changes the subtitle font size.
Repeat: Turn on/off repeat function
of movie playback. When turned on,
the file within the folder will be played
back repeatedly.
85
MY MEDIA
* Image shown may differ from your TV.
Set Video Menu Options
6HW9LGHR
âŤÜâŹ
3LFWXUH0RGH
6WDQGDUG
âŤŰ˝âŹ
MY MEDIA
Ř%DFNOLJKW
âŤÜâŹ
âŤŰ˝âŹ
Ř&RQWUDVW
âŤÜâŹ
âŤŰ˝âŹ
Ř%ULJKWQHVV
âŤÜâŹ
âŤŰ˝âŹ
Ř&RORU
âŤÜâŹ
âŤŰ˝âŹ
Ř'\QDPLF&RQWUDVW
âŤÜâŹ
0HGLXP
âŤŰ˝âŹ
Ř(GJH(QKDQFHU
âŤÜâŹ
+LJK
âŤŰ˝âŹ
Ř1RLVH5HGXFWLRQ
âŤÜâŹ
0HGLXP
âŤŰ˝âŹ
âŤÜâŹ
/RZ
âŤŰ˝âŹ
7UX0RWLRQ
('TruMotion' dependent on model)
áŻ3LFWXUH5HVHW
á°3UHYLRXV
Select Picture Mode or TruMotion.
Make appropriate adjustments.
%/8(
Reset picture settings to default.
Set Audio Menu Options
6HW$XGLR
6RXQG0RGH
âŤÜâŹ
6WDQGDUG
âŤŰ˝âŹ
$XWR9ROXPH
âŤÜâŹ
2II
âŤŰ˝âŹ
&OHDU9RLFH,,
âŤÜâŹ
2II
âŤŰ˝âŹ
%DODQFH ⍠ÜâŹ/
âŤŰ˝âŹ
á°3UHYLRXV
86
Select Sound Mode, Auto Volume, Clear
Voice II or Balance.
Make appropriate adjustments.
PHOTO LIST
The On-Screen Display on your model may be slightly different.
Supported photo file: *.JPG
ᯍ Baseline: 64 pixel (width) x 64 pixel (height) to 15360 pixel (width) x 8640 pixel (height)
ᯍ Progressive: 64 pixel (width) x 64 pixel (height) to 1920 pixel (width) x 1440 pixel (height)
ᯍ You can play JPEG files only.
ᯍ Non-supported files are displayed in the form of predefined icon.
Screen Components
MENU
ENTER
Select MY MEDIA.
ENTER
Select Photo List.
Moves to upper level folder
Current page/total pages
Corresponding buttons on the
remote control
Contents under the folder
focused on 1
Current page/total pages of
contents
MY MEDIA
3DJH
3KRWR/LVW
86%;7,&.
3DJH
'ULYH
3
3
3
3
3
3
3
3
3
áŻ0RYHáŻ9LHZáą3DJH&KDQJHáą
0DUN
áŻ7R0XVLF/LVW
áŻ&KDQJH1XPEHUV
áŻ0DUN0RGH
á°ż([LW
*5((1
Move to Music List or Movie List.
<(//2:
Change Numbers: Changes the number or thumbnails displayed at a time.
%/8(
Allows you to mark certain files.
EXIT
Return to TV viewing.
87
MY MEDIA
Photo Selection
3DJH
3KRWR/LVW
86%;7,&.
3DJH
'ULYH
áŻ0RYHáŻ9LHZáą3DJH&KDQJHáą
0DUN
ᯍ
MY MEDIA
áŻ7R0XVLF/LVW
áŻ&KDQJH1XPEHUV
Select the target folder or drive.
áŻ0DUN0RGH
á°ż([LW
ENTER
ENTER
Select the desired photos.
Photo file is displayed.
Use the CH (á°á°) button to navigate
in the photo page.
Mark Mode
3DJH
Select the target folder or drive.
3KRWR/LVW
0DUN0RGH
3DJH
'ULYH
86%;7,&.
ENTER
MARK
FAV
5('
áŻ0RYHáŻ0DUNáą3DJH&KDQJHáą
0DUN
áŻ9LHZ0DUNHG
5('
áŻ8QPDUN$OO
áŻ([LW0DUN0RGH
View Marked: Display the selected photo.
Mark All: Mark all photos on the screen.
<(//2:
Unmark All: Deselect all marked photos.
Exit the Mark Mode.
Mark your desired photo files.
View the marked photo files.
á°ż([LW
*5((1
%/8(
88
áŻ0DUN$OO
Select the desired
photo files.
ᯍ
When one or more photos are
marked, you can view individual photos or a slide show of the marked
photos. If no photos are marked, you
can view all photos individually or all
photos in the folder in a slide show.
Full Screen Menu
More operations are available in full screen mode.
3DJH
3KRWR/LVW
86%;7,&.
3DJH
'ULYH
áŻ0RYHáŻ9LHZáą3DJH&KDQJHáą
0DUN
áŻ&KDQJH1XPEHUV
áŻ0DUN0RGH
MY MEDIA
áŻ7R0XVLF/LVW
á°ż([LW
BDMSJ
[
.%
âŤÜâŹ
âŤŰ˝âŹ
âŤÜâŹ
6OLGHVKRZṼ
%*0Ṽ
Ṩ
ᯜ
á°
The aspect ratio of a photo may change the size
of the photo displayed on the screen in full size.
âŤŰ˝âŹ
áą2SWLRQ
á°+LGH
Select the target folder or drive.
ENTER
ENTER
á°ż([LW
ᯍ
Use the CH (á°á°) button to navigate
in the photo page.
Select the desired photos.
The selected photo is displayed in full
size.
89
BDMSJ
[
.%
ENTER
Select the Slideshow,
âŤÜâŹ
BGM, Ṩ(Rotate),
âŤŰ˝âŹ
ᯜ(Zoom In), á°(Energy Saving),
Option, or Hide.
ᯍ
âŤÜâŹ
MY MEDIA
âŤŰ˝âŹ
MY MEDIA
6OLGHVKRZṼ
%*0Ṽ
Ṩ
ᯜ
á°
âŤŰ˝âŹ
áą2SWLRQ
á°+LGH
Use ! button to select the previous or next photo.
á°ż([LW
Ĺš Slideshow: Selected photos are displayed during the slide show. If no photo is selected, all photos
in the current folder are displayed during slide show.
ᯍ Set the time interval of the slide show in Option-Set Photo View. menu (Refer to p. 91).
ᯍ You can adjust Option by using the Q.MENU button on the remote control.
Ĺš BGM (Background Music): Listen to music while viewing photos in full size.
ᯍ Set the BGM device and album in Option-Set Photo View. menu (Refer to p. 91).
ᯍ You can adjust Option by using the Q.MENU button on the remote control.
Ś Ṩ(Rotate): Rotate photos.
ᯍ Rotates the photo 90 °, 180 °, 270 °, 360 ° clockwise.
ᯍ Photos cannot be rotated if its width is greater than the available supported resolution height.
Ś ᯜ(Zoom In): View the photo by zoom in 2, 4 times by using Blue button.
Ĺš á°(Energy Saving): Increase the brightness of your screen by using ENERGY SAVING button.
Ĺš Option: Set values for Slide Speed and Music Album (Refer to p. 91).
ᯍ You cannot change Music Album while BGM is playing.
ᯍ You can only select the MP3 folder saved on the device that currently displays the photo.
ĹšHide: Hide the menu on the full-sized screen.
ᯍ To see the menu again on the full-sized screen, press ENTER button to display.
ĹšExit: Move to the previous menu screen.
90
Using the Photo List Function
BDMSJ
[
.%
&KRRVHRSWLRQV
6HW3KRWR9LHZ
âŤÜâŹ
âŤŰ˝âŹ
6HW9LGHR
6HW$XGLR
&ORVH
6OLGHVKRZṼ
Q.MENU
%*0Ṽ
Ṩ
ᯜ
á°
âŤŰ˝âŹ
áą2SWLRQ
á°+LGH
Show the Option menu.
ENTER
MY MEDIA
âŤÜâŹ
Select Set Photo View., Set Video.,
or Set Audio.
á°ż([LW
! NOTE
Ĺš Option values changed in Photo List do
not affect Movie List and Music List.
Ĺš Option values changed in Photo List or
Music List are changed likewise in Photo
List and Music List, but not Movie List.
Set Photo View Menu Options
6HW3KRWR9LHZ
6OLGH6SHHG
âŤÜâŹ
0XVLF$OEXP
)DVW
âŤŰ˝âŹ
'ULYH
Ř5HSHDW
âŤÜâŹ
2Q
âŤŰ˝âŹ
Ř5DQGRP
âŤÜâŹ
2II
âŤŰ˝âŹ
á°3UHYLRXV
Select Slide Speed or Music Album.
Make appropriate adjustments.
91
MY MEDIA
* Image shown may differ from your TV.
Set Video Menu Options
6HW9LGHR
3LFWXUH0RGH
âŤÜâŹ
6WDQGDUG
âŤŰ˝âŹ
Ř%DFNOLJKW
âŤÜâŹ
âŤŰ˝âŹ
Ř&RQWUDVW
âŤÜâŹ
âŤŰ˝âŹ
Ř%ULJKWQHVV
âŤÜâŹ
âŤŰ˝âŹ
Ř&RORU
âŤÜâŹ
âŤŰ˝âŹ
Ř'\QDPLF&RQWUDVW
âŤÜâŹ
0HGLXP
âŤŰ˝âŹ
Ř(GJH(QKDQFHU
âŤÜâŹ
+LJK
âŤŰ˝âŹ
Ř1RLVH5HGXFWLRQ
âŤÜâŹ
0HGLXP
âŤŰ˝âŹ
âŤÜâŹ
/RZ
âŤŰ˝âŹ
MY MEDIA
7UX0RWLRQ
(depending on models)
áŻ3LFWXUH5HVHW
á°3UHYLRXV
Select Picture Mode or TruMotion.
Make appropriate adjustments.
%/8(
Initialize the adjusted picture value.
Set Audio Menu Options
6HW$XGLR
6RXQG0RGH
âŤÜâŹ
6WDQGDUG
âŤŰ˝âŹ
$XWR9ROXPH
âŤÜâŹ
2II
âŤŰ˝âŹ
&OHDU9RLFH,,
âŤÜâŹ
2II
âŤŰ˝âŹ
%DODQFH ⍠ÜâŹ/
âŤŰ˝âŹ
á°3UHYLRXV
92
Select Sound Mode, Auto Volume, Clear
Voice II or Balance.
Make appropriate adjustments.
MUSIC LIST
This TV cannot play back copy-protected files.
The On-Screen Display on your model may be slightly different.
MUSIC (*.MP3) supporting file
Bit rate 32 Kbps - 320 Kbps
⢠Sampling rate MPEG1 Layer3: 32 kHz, 44.1 kHz, 48 kHz
⢠Sampling rate MPEG2 Layer3: 16 kHz, 22.05 kHz, 24 kHz
⢠Sampling rate MPEG2.5 Layer3: 8 kHz, 11.025 kHz, 12 kHz
MENU
ENTER
Select MY MEDIA.
ENTER
Select Music List.
Preview: If any album jacket for
the file (Album Art Image)
exists, this picture is displayed.
Moves to upper level folder
Current page/Total pages
Corresponding buttons on the
remote control
Contents under the folder
focused on 1
Current page/total pages of
contents
MY MEDIA
Screen Components
3DJH
0XVLF/LVW
'ULYH
86%;7,&.
%PS
%PS
3DJH
%PS
%PS
%PS
áŻ0RYHáŻ3OD\áą3DJH&KDQJHáą
0DUN
áŻ7R0RYLH/LVW
áŻ&KDQJH1XPEHUV
áŻ0DUN0RGH
á°ż([LW
*5((1
Move to Movie List or Photo List.
<(//2:
Change Numbers: Changes the number or thumbnails displayed at a time.
%/8(
Allows you to mark certain files.
EXIT
Return to TV viewing.
ENERGY
SAVING
Press the ENERGY SAVING button repeatedly to increase the brightness of your
screen (Refer to p. 104).
(It's available "ENERGY SAVING - Off, Screen Off" only.)
93
MY MEDIA
Music Selection
3DJH
0XVLF/LVW
'ULYH
86%;7,&.
Select the target folder or drive.
3DJH
%PS
%PS
%PS
%PS
ENTER
%PS
Select the desired
music file.
ENTER
Music files are played.
áŻ0RYHáŻ3OD\áą3DJH&KDQJHáą
0DUN
áŻ7R0RYLH/LVW
áŻ&KDQJH1XPEHUV
áŻ0DUN0RGH
á°ż([LW
ᯍ
MY MEDIA
Use the CH (á°á°) button to navigate
in the music page.
Mark Mode
3DJH
0XVLF/LVW
Select the target folder or
drive.
0DUN0RGH
'ULYH
86%;7,&.
%PS
%PS
3DJH
%PS
%PS
%PS
ENTER
MARK
FAV
áŻ0RYHáŻ0DUNáą3DJH&KDQJHáą
0DUN
áŻ3OD\0DUNHG
5('
áŻ8QPDUN$OO
áŻ([LW0DUN0RGH
Play Marked: Play the selected songs. Once a
song finishes playing, the next selected one
will be played automatically.
Mark All: Mark all songs in the folder.
<(//2:
Unmark All: Deselect all marked song.
Exit the Mark Mode.
5('
á°ż([LW
*5((1
%/8(
94
áŻ0DUN$OO
ᯍ
Select the desired
music file.
Mark your desired music file.
Play the marked music file.
When one or more music files are
marked, the marked music files will
be played in sequence.
Using the Music List Function
3DJH
0XVLF/LVW
ILOH V 0DUNHG
'ULYH
&KRRVHRSWLRQV
3DJH
6HW$XGLR3OD\
á°Ś
6HW$XGLR
ᯥ
%PS
%PS
0DG )HDW PS
á°§
Q.MENU
á°¨
á°Ş
á°Š
%PS
%PS
áŻáŻ
áŻ3OD\ZLWK3KRWR
%PS
á°
áą2SWLRQ
á°+LGH
Show the Option menu.
ENTER
&ORVH
Select Set Audio Play. or Set Audio..
á°ż([LW
! NOTE
MY MEDIA
á°Ś
á°Ś
ᯥ
ᯥ
Ĺš Option values changed in Movie List
does not affect Photo List and Music
List.
Ĺš Option value changed in Photo List and
Music List are changed likewise in Photo
List and Music List excluding Movie List.
Ĺš You can listen to the music only within
the device currently played.
Using the remote control
Stop playback.
Return to normal playback.
Paused playback.
Select the previous or next song.
*5((1
ENERGY
SAVING
Play with Photo: Start playing the selected songs and then move to the Photo List.
Press the ENERGY SAVING button repeatedly to increase the brightness of your screen
(Refer to p. 104). (It's available "ENERGY SAVING - Off, Screen Off" only.)
A cursor indicating the position can be played on the screen.
EXIT
Move to the previous menu screen.
95
MY MEDIA
Set Audio Play Menu Options
6HW$XGLR3OD\
5HSHDW
âŤÜâŹ
2Q
âŤŰ˝âŹ
5DQGRP
âŤÜâŹ
2II
âŤŰ˝âŹ
á°3UHYLRXV
Select Repeat or Random.
MY MEDIA
Make appropriate adjustments.
Set Audio Menu Options
6HW$XGLR
6RXQG0RGH
âŤÜâŹ
6WDQGDUG
âŤŰ˝âŹ
$XWR9ROXPH
âŤÜâŹ
2II
âŤŰ˝âŹ
&OHDU9RLFH,,
âŤÜâŹ
2II
âŤŰ˝âŹ
%DODQFH ⍠ÜâŹ/
âŤŰ˝âŹ
á°3UHYLRXV
Select Sound Mode, Auto Volume, Clear
Voice II or Balance.
Make appropriate adjustments.
ᯍ
If you don't press any buttons for a while, the play information box
will float across the screen. This prevents screen pixel damage due
to a fixed image remaining on the screen for a extended period of
time.
%PS
á°Ś
! NOTE
96
Ĺš Music files with copy-protection will not play.
Ĺš Press ENTER or á°§ button to stop the screen saver.
EXTRA CONTENTS
- For 32/37/42/47LD452C
You can play application files on USB device.
Application files your device can be played by this unit.
The On Screen Display may be different from your TV. Images are an example to assist with the TV
operation.
FLASH (*.SWF) / GEM supporting file
An SWF file complied with Flash Lite 3.0 or earlier (the 3.0 version is recommended)
MY MEDIA
⢠The Pro: Centric application is required, which starts automatically in the flash memory when the
TV is turned on.
⢠The folder called /hcapfs/as/abs_service/ must exist in USB drive root directory.
⢠The file called xait.xml must exist in the /hcapfs/as/abs_service/ folder.
⢠If the above conditions are not met, the following error message is displayed when selecting the
Extra Contents option: Failed to execute file in the USB. Please check the files in the USB.
⢠When the flash file does not run even if the above all conditions are met, refer to the Download Extra
Contents of Installation Guide.
⢠GEM is composed of JAVA application.
Playing the application files
MENU
Select MY MEDIA.
ENTER
ENTER
Select Extra Contents.
Application files are played.
To stop playing the Application file
Remove the USB from the USB IN jack of the TV set.
! NOTE
Ĺš When playing the Application files(FLASH or GEM files), the buttons are controlled according
to the settings of the Extra Contents option.
97
MY MEDIA
EZSIGN TV
- For 32/42/47LD452B
The EzSign TV function allows you to play and manage high-quality ad content that you create quickly
and easily using the EzSign TV Editor.
ᯍ For more information of using, refer to the EzSign TV Editor S/W & Manual.
86%
â 79PHPRU\
(]6LJQ79FRQWHQWH[LVWV+RZGR\RXZDQW
WRPDQDJHWKLVFRQWHQW"
3OD\
0<0(',$
'HOHWH
&ORVH
or
(]6LJQ79
3KRWR/LVW
0XVLF/LVW
79PHPRU\
â 86%
MY MEDIA
+RZGR\RXZDQWWRSOD\WKH(]6LJQ79
&RQWHQW"
&RS\WR79PHPRU\ 3OD\
3OD\
&ORVH
MENU
Select MY MEDIA.
ENTER
Select TV memory or USB.
ENTER
ENTER
Select EzSign TV.
ᯍ
The highlighted tab with the "â" symbol indicates the location of the file
currently being played
TV memory
3OD\
Plays EzSign TV content in the memory.
'HOHWH
Deletes EzSign TV content from the memory. (Your TV restarts after the content is deleted.)
&ORVH
Closes the EzSign TV menu window.
USB
Copies a file from the USB memory to the EzSign TV memory and plays it.
&RS\WR79PHPRU\
(Once the file has been copied, it can be played even when it is removed from
3OD\
the USB memory.)
3OD\
&ORVH
Plays a file directly from the USB memory without copying it to the EzSign TV memory.
Closes the EzSign TV menu window.
! NOTE
98
Ĺš While loading EzSign TV content, your TV may function slower than normal.
Ĺš It is recommended that you copy files to the TV memory before playing them, as playing
directly from the USB memory for an extended period of time may cause the device to overheat.
DIVX REGISTRATION CODE
Except 32/42/47LD420, 32/37/42/47LD450, 37/42/47LD450C, 32/42/47/55LD520, 55LD520C,
42/47/55LE530C, 42/47LD451C, 32/37/42/47LD452C, 32/42/47LD452B, 26LD352C)
Using the registration number, movies can be rented or purchased at www.divx.com/vod.
Only DivX files matched with the registration code of the purchased TV are playable.
'LY;5HJ&RGH
0<0(',$
'HDFWLYDWLRQ
0RYLH/LVW
MENU
0XVLF/LVW
Select MY MEDIA.
ENTER
%/8(
Select DivX Option.
á°3UHYLRXV
&ORVH
Select DivX Reg. Code.
ENTER
MY MEDIA
3KRWR/LVW
Source Exif Data:
File Type : PDF
File Type Extension : pdf
MIME Type : application/pdf
PDF Version : 1.6
Linearized : Yes
XMP Toolkit : 3.1-702
Producer : Acrobat Distiller 7.0 (Windows)
Create Date : 2011:04:13 09:40:55+09:00
Modify Date : 2011:04:14 11:44:09+09:00
Metadata Date : 2011:04:14 11:44:09+09:00
Thumbnail Format : JPEG
Thumbnail Width : 256
Thumbnail Height : 256
Thumbnail Image : (Binary data 3424 bytes, use -b option to extract)
Document ID : uuid:C36136A66665E011A4C184E902F91345
Instance ID : uuid:6be9a71b-c3cd-4042-a805-181f99b2ce5e
Derived From Instance ID : uuid:4a5bacc3-a2c5-43f1-817d-4d6b2160609b
Derived From Document ID : xmp.did:E2057B01835EE0119DC0D78F3AA315A5
Derived From Rendition Class : proof:pdf
Doc Change Count : 39120
Format : application/pdf
Title : untitled
Has XFA : No
Page Count : 80
EXIF Metadata provided by EXIF.tools