LG Electronics USA 37LH260HUA LCD TV MONITOR User Manual EMISSION TEST REPORT

LG Electronics USA LCD TV MONITOR EMISSION TEST REPORT

Users Manual

  Order Number  : GETEC-C1-09-207  FCC Class B Certification Test Report Number  : GETEC-E3-09-120  Page 1 / 1  EUT Type: LCD TV/Monitor   APPENDIX G : USER’S MANUAL    FCC ID.: BEJ37LH260HUA
LCD TVOWNER’S MANUAL32LH240H32LH250H37LH250H32LH255H37LH255H42LH255H37LH260H42LH260HP/NO : SAC34026002 (0908-REV02)www.lgcommercial.comThis product qualifies for ENERGY STAR in the “factory default(Home Use)” setting.Changing the factory default settings or enabling other fea-tures may increase power consumption that could exceed thelimits necessary to quality for ENERGY STAR.1-800-243-0000   USA, Consumer User1-888-865-3026   USA, Commercial User1-888-542-2623   CANADALG Customer Information CenterModel:Serial:please read this manual carefully before operatingyour set.Retain it for future reference.Record model number and serial number of the set.See the label attched on the back cover and quotethis information to your dealerwhen you require service.
1WARNING  / CAUTIONWARNING / CAUTIONTo prevent fire or shock hazards, do not exposethis product to rain or moisture.FCC NOTICEClass B digital deviceThis equipment has been tested and found to complywith the limits for a Class B digital device, pursuant toPart 15 of the FCC Rules. These limits are designedto provide reasonable protection against harmfulinterference in a residential installation. This equipmentgenerates, uses and can radiate radio frequency energyand, if not installed and used in accordance with theinstructions, may cause harmful interference to radiocommunications. However, there is no guarantee thatinterference will not occur in a particular installation.If this equipment does cause harmful interference toradio or television reception, which can be determinedby turning the equipment off and on, the user isencouraged to try to correct the interference by oneor more of the following measures:- Reorient or relocate the receiving antenna.- Increase the separation between the equipment andreceiver.- Connect the equipment to an outlet on a circuitdifferent from that to which the receiver is connected.- Consult the dealer or an experienced radio/TVtechnician for help.This device complies with part 15 of the FCC Rules.Operation is subject to the following two condi-tions: (1) This device may not cause (harmful)interference, and (2) this device must accept anyinterference received, including interference thatmay cause undesired operation (of the device).Any changes or modifications in construction of thisdevice which are not expressly approved by the partyresponsible for compliance could void the user’sauthority to operate the equipment.CAUTIONDo not attempt to modify this product in any waywithout written authorization from LG Electronics.Unauthorized modification could void the user’sauthority to operate this product The lightning flash with arrowheadsymbol, within an equilateral triangle, isintended to alert the user to the presenceof uninsulated “dangerous voltage” within theproduct’s enclosure that may be of sufficientmagnitude to constitute a risk of electric shock topersons.The exclamation point within an equilateraltriangle is intended to alert the user tothe presence of important operatingand maintenance (servicing) instructions in theliterature accompanying the appliance.TO REDUCE THE RISK OF ELECTRIC SHOCKDO NOT REMOVE COVER (OR BACK). NOUSER SERVICEABLE PARTS INSIDE. REFER TOQUALIFIED SERVICE PERSONNEL.WARNING/CAUTIONTO REDUCE THE RISK OF FIRE AND ELECTRICSHOCK, DO NOT EXPOSE THIS PRODUCT TORAIN OR MOISTURE.NOTE TO CABLE/TV INSTALLERThis reminder is provided to call the CATV systeminstaller’s attention to Article 820-40 of the NationalElectric Code (U.S.A.). The code provides guidelines forproper grounding and, in particular, specifies that thecable ground shall be connected to the grounding systemof the building, as close to the point of the cable entryas practical.
Read these instructions.Keep these instructions.Heed all warnings.Follow all instructions.Do not use this apparatus near water.Clean only with dry cloth.Do not block any ventilation openings. Install inaccordance with the manufacturer’s instructions.Do not install near any heat sources such asradiators, heat registers, stoves, or other apparatus(including amplifiers)that produce heat.Do not defeat the safety purpose of the polarizedor grounding-type plug. A polarized plug hastwo blades with one wider than the other. Agrounding type plug has two blades and a thirdgrounding prong, The wide blade or the thirdprong are provided for your safety. If the providedplug does not fit into your outlet, consult anelectrician for replacement of the obsolete outlet.Protect the power cord from being walked onor pinched particularly at plugs, conveniencereceptacles, and the point where they exit fromthe apparatus.Only use attachments/accessories specified bythe manufacturer.Use only with the cart, stand, tripod, bracket,or table specified by the manufacturer, or soldwith the apparatus. When a cart is used, usecaution when moving the cart/apparatuscombination to avoid injury from tip-over.Unplug this apparatus during lighting storms orwhen unused for long periods of time.Refer all servicing to qualified service personnel.Servicing is required when the apparatus has beendamaged in any way, such as power-supply cord orplug is damaged, liquid has been spilled or objectshave fallen into the apparatus, the apparatus hasbeen exposed to rain or moisture, does not operatenormally, or has been dropped.2IMPORTANT SAFETY INSTRUCTIONSSAFETY INSTRUCTIONS12345786910
3Never touch this apparatus or antenna during athunder or lighting storm. When mounting a TV on the wall, make sure not toinstall the TV by the hanging power and signalcables on the back of the TV.Do not allow an impact shock or any objects to fallinto the product, and do not drop onto the screenwith something.CAUTION concerning the Power Cord :It is recommend that appliances be placed upon adedicated circuit; that is, a single outlet circuit whichpowers only that appliance and has no additionaloutlets or branch circuits. Check the specificationpage of this owner's manual to be certain.Do not connect too many appliances to the sameAC power outlet as this could result in fire or elec-tric shock.Do not overload wall outlets. Overloaded wall out-lets, loose or damaged wall outlets, extension cords,frayed power cords, or damaged or cracked wireinsulation are dangerous. Any of these conditionscould result in electric shock or fire. Periodicallyexamine the cord of your appliance, and if itsappearance indicates damage or deterioration,unplug it, discontinue use of the appliance, andhave the cord replaced with an exact replacementpart by an authorized servicer. Protect the powercord from physical or mechanical abuse, such asbeing twisted, kinked, pinched, closed in a door, orwalked upon. Pay particular attention to plugs, walloutlets, and the point where the cord exits theappliance. Do not make the TV with the power cord pluggedin. Do not use a damaged or loose power cord. Besure do grasp the plug when unplugging the powercord. Do not pull on the power cord to unplug theTV. WARNING - To reduce the risk of fire or electricalshock, do not expose this product to rain, moistureor other liquids. Do not touch the TV with wethands. Do not install this product near flammableobjects such as gasoline or candles or expose theTV to direct air conditioning. Do not expose to dripping or splashing and do notplace objects filled with liquids, such as vases, cups,etc. on or over the apparatus (e.g. on shelves abovethe unit).GGRROOUUNNDDIINNGGEnsure that you connect the earth ground wire toprevent possible electric shock. (i.e. a TV with athree-prong grounded AC plug must be connectedto a three-prong grouned AC outlet) If groundingmethods are not possible, have a qualified electri-cian install a separate circuit breaker.  Do not try to ground the unit by connecting it totelephone wires, lightening rods, or gas pipes.DDIISSCCOONNNNEECCTTIINNGG  DDEEVVIICCEE  FFRROOMM  MMAAIINNSSMains plug is the disconnecting device. The plugmust remain readily operable.12111413161718Power SupplyShort-circuitBreaker15
4AANNTTEENNNNAASSOOuuttddoooorr  aanntteennnnaa  ggrroouunnddiinnggIf an outdoor antenna is installed, follow the precau-tions below. An outdoor antenna system should notbe located in the vicinity of overhead power lines orother electric light or power circuits, or where it cancome in contact with such power lines or circuits asdeath or serious injury can occur.Be sure the antenna system is grounded so as to pro-vide some protection against voltage surges andbuilt-up static charges. Section 810 of the National Electrical Code (NEC) inthe U.S.A. provides information with respect to prop-er grounding of the mast and supporting structure,grounding of the lead-in wire to an antenna dis-charge unit, size of grounding conductors, location ofantenna discharge unit, connection to groundingelectrodes and requirements for the grounding elec-trode. AAnntteennnnaa  ggrroouunnddiinngg  aaccccoorrddiinngg  ttoo  tthheeNNaattiioonnaall  EElleeccttrriiccaall  CCooddee,,  AANNSSII//NNFFPPAA  7700CleaningWhen cleaning, unplug the power cord and scrubgently with a soft cloth to prevent scratching. Do notspray water or other liquids directly on the TV aselectric shock may occur. Do not clean with chemi-cals such as alcohol, thinners or benzene.MovingMake sure the product is turned off, unpluggedand all cables have been removed. It may take 2 ormore people to carry larger TVs. Do not pressagainst or put stress on the front panel of the TV. VentilationInstall your TV where there is proper ventilation. Donot install in a confined space such as a bookcase.Do not cover the product with cloth or other mate-rials (e.g.) plastic while plugged in. Do not install inexcessively dusty places.   If you smell smoke or other odors coming from theTV or hear strange sounds, unplug the power cordcontact an authorized service center.Do not press strongly upon the panel with a hand orsharp object such as nail, pencil or pen, or make ascratch on it.Keep the product away from direct sunlight.FFoorr  LLCCDD  TTVVIf the TV feels cold to the touch, there may bea small “flicker” when it is turned on. This isnormal, there is nothing wrong with TV.Some minute dot defects may be visible on thescreen, appearing as tiny red, green, or bluespots. However, they have no adverse effect onthe monitor's performance.Avoid touching the LCD screen or holding yourfinger(s)  against it for long periods of time.Doing so may produce some temporary dis-tortion effects on the screen.2119Antenna Lead in WireAntenna Discharge Unit(NEC Section 810-20)Grounding Conductors(NEC Section 810-21)Ground ClampsPower Service GroundingElectrode System (NECArt 250, Part H)Ground ClampElectric ServiceEquipmentNEC: National Electrical Code2223242520ON DISPOSAL (Only Hg lamp used LCD TV)The fluorescent lamp used in this product containsa small amount of mercury.  Do not dispose ofthis product with general household waste.Disposal of this product must be carried out inaccordance to the regulations of your local authority.26
5CONTENTSWARNING / CAUTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . 2FEATURES OF THIS TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7PREPARATIONAccessories  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Front Panel Information  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Back Panel Information  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10Stand Instruction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12VESA Wall Mounting  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14Cable Management  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15Desktop Pedestal Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16Swivel Stand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16Attaching the TV to a desk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17Securing the TV to the wall to prevent falling When the TV is used on a stand . . . . . . . . . . . . . . . . . . . . . . . . . . 18Antenna or Cable Connection . . . . . . . . . . . . . . . . . . . . . . . . . . 19EXTERNAL EQUIPMENT SETUPHD Receiver Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20DVD Setup  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23VCR Setup  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25Other A/V Source Setup  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26PC Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27USB Connection  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33WATCHING TV / CHANNEL CONTROLRemote Control Functions  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34Turning On TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36Channel Selection  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36Volume Adjustment  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36On-Screen Menus Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37Channel Setup - Auto Scan (Auto Tuning) . . . . . . . . . . . . . . . . . . . . . . . . . . . 38- Add / Delete Channel (Manual Tuning) . . . . . . 39- Channel Editing  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40Channel Label  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41Input List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42USBEntry Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43Photo List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45Music List  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49PICTURE CONTROLPicture Size (Aspect Ratio) Control . . . . . . . . . . . . . . . . . . 52Preset Picture Settings- Picture Mode - Preset  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54- Color Tone Preset  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55Manual Picture Adjustment - User Mode  . . . . . . . . . . 56Picture Improvement Technology  . . . . . . . . . . . . . . . . . . . . . 57Advanced Control - Black (Darkness) Level . . . . . . . 58Advanced Control - Eye Care  . . . . . . . . . . . . . . . . . . . . . . . . . . .59Advanced Control - Film Mode . . . . . . . . . . . . . . . . . . . . . . . . .60Picture Reset  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61Demo mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61SOUND & LANGUAGE CONTROLAuto Volume Leveler (Auto Volume)  . . . . . . . . . . . . . . . . . 62Preset Sound Settings (Sound Mode)  . . . . . . . . . . . . . . 63Sound Setting Adjustment - User Mode  . . . . . . . . . . . 64- SRS TruSurround XT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65Clear Voice  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66Balance  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67TV Speakers On/Off Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68Audio Reset  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69Stereo/SAP Broadcast Setup  . . . . . . . . . . . . . . . . . . . . . . . . . . . 70Audio Language  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71On-Screen Menus Language Selection . . . . . . . . . . . . . . 72Caption Mode- Analog Broadcasting System Captions  . . . . . . . 73- Digital Broadcasting System Captions  . . . . . . . . 74- Caption Option   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75TIME SETTINGClock Setting- Auto Clock Setup   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76- Manual Clock Setup  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77Auto On/Off Time Setting   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78Sleep Timer Setting  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
6PARENTAL CONTROL / RATINGSSet Password & Lock System  . . . . . . . . . . . . . . . . . . . . . . . . . . . 80Channel Blocking  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83Movie & TV Rating  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84Downloadable Rating  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87External Input Blocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88APPENDIXTroubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89Maintenance  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91Product Specifications  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91IR Codes  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92Open Source License  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
7FEATURES OF THIS TVis a trademark of SRS Labs, Inc.TruSurround XT technology is incorporated underlicense from SRS Labs, Inc.Manufactured under license from Dolby Laboratories.“Dolby“and the double-D symbol are trademarks ofDolby Laboratories. HDMITM, the HDMI logo and High-DefinitionMultimedia Interface are trademarks or registeredtrademarks of HDMI Licensing LLC."■When a fixed image (e.g. logos, screen menus, video game, and computer display) is displayed on the TVfor an extended period, it can become permanently imprinted on the screen. This phenomenon is knownas “image burn” or “burn-in.” Image burn is not covered under the manufacturer’s warranty. ■In order to prevent image burn, avoid displaying a fixed image on your TV screen for a prolonged period(2 or more hours for LCD, 1 or more hours for Plasma). ■Image burn can also occur on the letterboxedareas of your TV if you use the 4:3 aspectratio setting for an extended period.IMPORTANT INFORMATION TO PREVENT “IMAGE BURN/ BURN-IN” ON YOUR TV SCREENHigh-definition television. High-resolution digitaltelevision broadcast and playback system composedof roughly a million or more pixels, 16:9 aspect-ratioscreens, and AC3 digital audio. A subset of digitaltelevision, HDTV formats include 1080i and 720presolutions.View videos and photos and listen to music on yourTV through USB 2.0 (‘videos’ dependent on model).LG TV include a unique invisible speaker system,tuned by renowned audio expert, Mr. Mark Levinson.Speakers are embedded in strategic spots behind thefront cabinet and use minute vibrations to turn theentire front bezel into the speaker system. The resultis a clean, polished look, and enhanced audio byincreasing the “sweet spot”, giving a wider and richersound field. Automatically enhances and amplifies the sound ofhuman voice frequency range to help keep dialogueaudible when background noise swells.Matches the original frame rate of the film for a morefilm-like experience
8PREPERATIONACCESSORIESEnsure that the following accessories are included with your TV. If an accessory is missing, please contact thedealer where you purchased the TV. The accessories included may differ from the images below.1.5V 1.5VOwner’s Manual Power CordRemote Control,BatteriesLIST3567809FLASHBKMUTEVOLCHPAGERETURNENTERMENULIST1234567809FLASHBKMUTEVOLCHPAGERETURNMARKENTERINPUTPOWERRATIOCCTIMERALAMSAPEJECTCD ManualBolts for stand assembly(Refer to P.12) Screw for stand fixing(Refer to P.17)Protection Cover(Refer to P.13)x 4OOppttiioonn  EExxttrraass* Wipe spots on the exterior only withthe polishing cloth.* Do not wipe roughly when removingstain. Excessive pressure may causescratch or discoloration.Polishing ClothNot included with all modelsD-sub 15 pin CableWhen using the VGA (D-sub 15 pincable) PC connection, the usermust use shielded signal interfacecables with ferrite cores to maintainstandards compliance.Protective Bracket and Bolt forPower Cord (This feature is not available for all models.)(Refer to P.15)Cable Holder(Refer to P.15)Plug in type holder(Refer to P.15)x 2Torx plus Star head screw(Refer to P.12)
PREPARATION9FRONT PANEL INFORMATION■Image shown may differ from your TV.INPUTMENUENTERCHVOLCHANNEL (DD,EE)ButtonsVOLUME (+, -) ButtonsENTER ButtonMENU ButtonINPUT ButtonPOWER ButtonSPEAKERRemote Control Sensor,Power/Standby IndicatorIlluminates red in standby mode.Illuminates blue when the TV is switched on.
PREPARATION10■Image shown may differ from your TV.BACK PANEL INFORMATIONAV IN 2L/MONORAUDIOVIDEOUSB INRS-232C IN(SERVICE ONLY)AUDIO INVIDEOAUDIORGB IN (PC)VIDEO AUDIOL(MONO)R21L R/DVI INCOMPONENT INAV IN 1UPDATERESET(RGB/DVI)REMOTECONTROL  OUTSPEAKER OUT       (8   )RJPTV - LINKCFGGAMECONTROLR8210R(            )ANTENNA INANTENNA INM.P.I.M.P.I.714356121315142PREPARATION911RS-232C IN(SERVICE ONLY)AUDIO INVIDEOAUDIORGB IN (PC)VIDEO AUDIOL(MONO)R21L R/DVI INCOMPONENT INAV IN 1UPDATERESET(RGB/DVI)REMOTECONTROL  OUTSPEAKER OUT       (8   )RJPR821074356932/37/42LH250H, 32/37/42LH255H, 37/42LH260H32LH240H
PREPARATION11RJP (REMOTE JACK PACK PORT)Connect to remote jack pack control output port.TV - LINK CFGUsed for FTG ConfigurationUSB INUsed for viewing photos and listening to MP3s.ANTENNA INConnect over-the air signals to this jack.M.P. I.Control port.Power Cord SocketFor operation with AC power. Caution: Never attempt to operate the TV on DCpower.GAME CONTROLControl portAV (Audio/Video) IN    Analog composite connection. Supports standarddefinition video only (480i). Used for PC/DTV audio input jack.COMPONENT IN Analog Connection. Supports HD. Uses a red, green, and blue cable for video & a redand white cable for audio.HDMI/DVI INDigital Connection. Supports HD video and Digitalaudio.  Accepts DVI video using an adapter or HDMI toDVI cable (not included)SPEAKER OUT 8ΩConnect to external speaker input.REMOTE CONTROL OUTIR output for controlling an auxiliary device.UPDATEEnables/disables software downloads and debugmode.RESETPerforms a hardware reset.RGB IN (PC) Analog PC Connection. Uses a D-sub 15 pin cable(VGA cable).AUDIO IN (RGB/DVI) 1/8” headphone jack for analog PC audio input.RS-232C IN (SERVICE ONLY) Used for software updates.123459867101112131415
PREPARATION12STAND INSTRUCTIONPREPARATION■Image shown may differ from your TV.Carefully place the TV screen side down on acushioned surface to protect the screen fromdamage.Assemble the TV as shown.123INSTALLATIONGGWhen assembling the desk type stand, make surethe bolt is fully tightened (If not tightened fully,the TV can tilt forward after the product installa-tion). Do not  over tighten.NOTE!x 4Tighten the stand with the four screws (provided asparts of the TV).orTighten the two of these four screwsand the two Torx plus star headscrews (provided as parts of the TV) to secure theTV.  Tighten the two Torx plus star head screws witha star head driver bit (not provided as parts of theTV).x 2 x 2
PREPARATION13DETACHMENTCarefully place the TV screen side down on acushioned surface to protect the screen fromdamage.1Loose the bolts from TV.2Detach the stand from TV.3After removing the stand, install the includedpprrootteeccttiioonn  ccoovveerrover the hole for the stand.Press the PPRROOTTEECCTTIIOONN  CCOOVVEERRinto the TVuntil you hear it click.PROTECTION COVER
PREPARATION14PREPARATIONVESA WALL MOUNTINGInstall your wall mount on a solid wall perpendicular to the floor. When attaching to other building materials, pleasecontact your nearest installer.If installed on a ceiling or slanted wall, it may fall and result in severe personal injury.We recommend that you use an LG brand wall mount when mounting the TV to a wall.LG recommends that wall mounting be performed by a qualified professional installer.GGDo not install your wall mount kit while your TV is turned on. It may result in personalinjury due to electric shock.CAUTIONGGScrew length needed depends on the wall mountused. For further information, refer to the instruc-tions included with the mount.GGStandard dimensions for wall mount kits are shownin the table.GGWhen purchasing our wall mount kit, a detailedinstallation manual and all parts necessary forassembly are provided.GGDo not use screws longer then the standard dimen-sion, as they may cause damage to the inside tothe TV.GGFor wall mounts that do not comply with the VESAstandard screw specifications, the length of thescrews may differ depending on their specifica-tions.GGDo not use screws that do not comply with theVESA standard screw specifications.Do not use fasten the screws too strongly, this maydamage the TV or cause the TV to a fall, leading topersonal injury. LG is not liable for these kinds ofaccidents.GGLG is not liable for TV damage or personal injurywhen a non-VESA or non specified wall mount isused or the consumer fails to follow the TV installa-tion instructions.NOTE!ModelVESA (A *B)Standard Screw Quantity Wall Mounting Bracket(sold separately)37LH250H,37LH255H,37LH260H,42LH250H,42LH255H,42LH260H32LH240H,32LH250H,32LH255H200 * 10 0 M 4 4200 * 200 M6 4AABBRW230 AW-47LG30MAW-47LG30M
PREPARATION15CABLE MANAGEMENT■Image shown may differ from your TV.Connect the cables as necessary.To connect additional equipment, see the EXTERNAL EQUIPMENT SETUP section. Secure the power cable with the PPROTECTIVEBRACKET/Screw or the Plug in type Holder.It will help prevent the power cable frombeing removed by accident.Install the CABLE MANAGEMENT CLIP asshown.If your TV has the CABLE HOLDER, install itas shown and bundle the cables.12Put the cables inside the CABLE MANAGEMENTCLIP and snap it closed.3GGDo not hold the CABLE MANAGEMENT CLIPwhen moving the TV.- If the TV is dropped, you may be injured or theproduct may be broken.GGWith some TVs, the PLUG IN TYPE HOLDERand the CABLE HOLDER are included. If theseholders are inserted into the hole provided onback of the TV, they cannot be removed.NOTE!CABLE MANAGEMENT CLIPCABLE HOLDERPROTECTIVE BRACKET/Screw(This feature is not available forall models.)PLUG IN TYPE HOLDEROr
PREPARATION16PREPARATIONDESKTOP PEDESTAL INSTALLATIONSWIVEL STAND After installing the TV, you can adjust the TV set manually to the left or right direction by 90 degrees to suityour viewing position.For proper ventilation, allow a clearance of 4 inches on all four sides from the wall.■Image shown may differ from your TV.4 inchesGGEnsure adequate ventilation by following the clearance recommendations.GGDo not mount near or above any type of heat source.CAUTION4 inches4 inches4 inches
PREPARATION17ATTACHING THE TV TO A DESK GGTo prevent TV from falling over, the TV should be securely attached to the floor/wall per installationinstructions. Tipping, shaking, or rocking the machine may cause injury.WARNING1-Screw(provided as parts of the product)DeskStand■Image shown may differ from your TV.The TV must be attached to a desk so it cannot be pulled in a forward/backward direction, potentially causinginjury or damaging the product. GGScrew: M5 x L (*L: Table depth + 8~10 mm)ex) Table depth: 15mm, Screw: M5 x 254-Screws(not provided as parts of the product)StandDesk
PREPARATION18PREPARATIONSECURING THE TV TO THE WALL TO PREVENT FALLINGWHEN THE TV IS USED ON A STANDWe recommend that you set up the TV close to a wall so it cannot fall over if pushed backwards. Additionally, we recommend that the TV be attached to a wall so it cannot be pulled in a forward direction,potentially causing injury or damaging the product. Caution: Please make sure that children don’t climb on or hang from the TV. ■Insert the eye-bolts (or TV brackets and bolts) to tighten the product to the wall as shown in the picture. *If your product has the bolts in the eye-bolts position before inserting the eye-bolts, loosen the bolts. * Insert the eye-bolts or TV brackets/bolts and tighten them securely in the upper holes.Secure the wall brackets with the bolts (sold separately) to the wall. Match the height of the bracket that ismounted on the wall to the holes in the product. Ensure the eye-bolts or brackets are tightened securely.■Use a sturdy rope (sold separately) to tie the product. It is safer to tiethe rope so it becomes horizontal between the wall and the product.■You should purchase necessary components to prevent the TV from tipping over (when not using a wall mount).■Image shown may differ from your TV.GGUse a platform or cabinet strong enough and large enough to support the size and weight of the TV.GGTo use the TV safely make sure that the height of the bracket on the wall and the one on the TV are the same.NOTE!
PREPARATION19R(            )ANTENNA INANTENNA IN M.P.I.ANTENNA OR CABLE CONNECTION1. Antenna (Analog or Digital)Wall Antenna Socket or Outdoor Antenna without a Cable BoxConnection.For optimum picture quality, adjust the direction if needed.2. CableWallAntennaSocketOutdoorAntenna(VHF, UHF)Cable TVWall JackMulti-family Dwellings/Apartments(Connect to wall antenna socket)RF Coaxial Wire (75 ohm)RF Coaxial Wire (75 ohm)Single-family Dwellings /Houses(Connect to wall jack for outdoor antenna)Be careful not to bend the copper wirewhen connecting the antenna.Copper Wire■To improve the picture quality in a poor signal area, please purchase a signal amplifier and install properly.   ■If the antenna needs to be split for two TV’s, install a 2-Way Signal Splitter.■If the antenna is not installed properly, contact your dealer for assistance.■To prevent damage do not connect to the power outlet until all connections are made between the devices.R(            )ANTENNA INANTENNA IN M.P.I.
PREPARATION20HD RECEIVER SETUPEXTERNAL EQUIPMENT SETUPThis TV can receive Digital Over-the-air or Digital Cable signals without an external digital set-top box. However,if you do receive digital signals from a digital set-top box or other digital external device, refer to the figure asshown below.Component Connection1. How to connectConnect the video outputs (Y, PB, PR)of the digital set-top box to the CCOOMMPPOONNEENNTT  IINN  VVIIDDEEOOjacks onthe TV. Match the jack colors (Y = green, PB= blue, andPR= red).Connect the audio output of the digital set-top box to the CCOOMMPPOONNEENNTT  IINN  AAUUDDIIOOjacks on the TV.212. How to use■Turn on the digital set-top box. (Refer to the owner’s manual for the digital set-top box.)■Select CCoommppoonneennttinput source using the IINNPPUUTT  buttonon the remote control.■To prevent the equipment damage, never plug in any power cords until you have finished connecting all equipment.■Image shown may differ from your TV. VIDEO AUDIOL(MONO)R2AV IN 1Y L RPBPR/DVI IN1VIDEOAUDIOCOMPONENT INL RGAMECONTROLSPEAKER OUT     REMOTCONTROL(8    )12Y, CB/PB, CR/PRSupported ResolutionsHorizontal Vertical Frequency(KHz)Frequency(Hz)15.73 59.9415.73 60.0031.47 59.9431.50 60.0044.96 59.9445.00 60.0033.72 59.9433.75 60.0067.432 59.9467.50 60.0027.00 24.0026.97 23.97633.75 30.0033.71 29.97Resolution 720x480i720x480p1280x720p1920x1080iSignal480i480p720p108 0 i1080 pComponentYesYesYesYesYesHDMINoYesYesYesYes1920x1080p
EXTERNAL EQUIPMENT SETUP21HDMI ConnectionConnect the digital set-top box to HHDDMMII  //DDVVII  IINN  11or HHDDMMII  22  jack on the TV.No separate audio connection is necessary. HDMI supports both audio and video.1. How to connect2. How to use■Turn on the digital set-top box. (Refer to the owner’s manual for the digital set-top box.)■Select  HHDDMMII11  or HHDDMMII22input source with using the IINNPPUUTTbutton on the remote control.21HDMI-DTVEOAUDIOVIDEO AUDIOL(MONO)RAV IN 1MPONENT INL R21/DVI INAUDIO INUPDATERESET(RGB/DVI)RS-232C IN(SERVICE ONLY)SPEAKER OUTRGB IN (PC)     REMOTECONTROL  OUT8(8    )HDMI OUTPUT1Horizontal Vertical Frequency(KHz)Frequency(Hz)31.47 59.9431.47 60.0044.96 59.9445.00 60.0033.72 59.9433.75 60.0067.432 59.93967.50 60.0027.00 24.0026.97 23.97633.75 30.0033.71 29.97  Resolution 720x480p1280x720p1920x1080i1920x1080p
EXTERNAL EQUIPMENT SETUP22EXTERNAL EQUIPMENT SETUPDVI to HDMI Connection RS-232C IN(SERVICE ONLY)VIDEOAUDIORGB IN (PC)VIDEO AUDIOL(MONO)RAV IN 1COMPONENT INL RL RDVI OUTPUT AUDIO21/DVI INGAMEONTROLAUDIO IN(RGB/DVI)     REMOTECONTROL  OUTSPEAKER OUT(8    )12GGA DVI to HDMI cable or adapter is required for thisconnection. DVI doesn't support audio, so a separateaudio connection is necessary.NOTE!Connect the DVI output of the digital set-top box tothe HHDDMMII//DDVVII  IINN  11jack on the TV.Connect the audio output of the digital set-top box tothe AAUUDDIIOO  IINN  ((RRGGBB//DDVVII))jack on the TV.1. How to connect2. How to use■Turn on the digital set-top box. (Refer to the owner’s man-ual for the digital set-top box.)■Select the HHDDMMII11input source on the TV using theIINNPPUUTTbutton on the remote control.21
EXTERNAL EQUIPMENT SETUP23DVD SETUPComponent ConnectionComponent Input portsTo get better picture quality, connect a DVD player to the component input ports as shown below.Component ports on the TVYPBPRVideo output ports on DVD playerYYYYPBB-YCbPbPRR-YCrPrConnect the video outputs (Y, PB, PR)of the DVD to theCCOOMMPPOONNEENNTT  IINN  VVIIDDEEOOjacks on the TV.Match the jack colors (Y = green, PB= blue, and PR= red).Connect the audio outputs of the DVD to the CCOOMMPPOONNEENNTT  IINN  AAUUDDIIOOjacks on the TV.1. How to connect2. How to use■Turn on the DVD player, insert a DVD.■Select the CCoommppoonneennttinput source on the TV using theIINNPPUUTTbutton on the remote control.■Refer to the DVD player's manual for operating instructions.21VIDEO AUDIOL(MONO)RAV IN 1Y L RPBPR21/DVI INVIDEOAUDIOCOMPONENT INL RGAMECONTROLR(SPEAKER OUT     REMOTECONTROL  O(8    )1 2
EXTERNAL EQUIPMENT SETUP24EXTERNAL EQUIPMENT SETUPHDMI ConnectionConnect the HDMI output of the DVD to theHHDDMMII//DDVVII  IINN  11  or HHDDMMII  22jack on the TV.No separate audio connection is necessary.HDMI supports both audio and video.1. How to connect2. How to use■Select the HHDDMMII11  or HHDDMMII22input source on the TVusing the IINNPPUUTTbutton on the remote control.■Refer to the DVD player's manual for operating instructions.21DEOAUDIOVIDEO AUDIOL(MONO)RAV IN 1OMPONENT INL R21/DVI INOLAUDIO INUPDATERESET(RGB/DVI)RS-232C IN(SERVICE ONLY)SPEAKER OUTRGB IN (PC)     REMOTECONTROL  OUT(8    )HDMI OUTPUT1Composite (RCA) ConnectionVIDEOAUDIOCOMPONENT INL R21/DVI INVIDEO AUDIOL(MONO)RAV IN 1L RVIDEOAUDIOGAMECONTROLARE(RSPEAKER OUT     REMOTECONTROL  OU(8    )Connect the AAUUDDIIOO/VVIIDDEEOOjacks between TV andDVD. Match the jack colors (Video = yellow, Audio Left= white, and Audio Right = red).1. How to connect2. How to use■Turn on the DVD player, insert a DVD.■Select the or AAVV11  input source on the TV using theIINNPPUUTTbutton on the remote control.  ■If connected to AAVV  IINN  22, select AAVV22input source on the TV.■Refer to the DVD player's manual for operating instructions.11
EXTERNAL EQUIPMENT SETUP25VCR SETUPAntenna ConnectionL RS-VIDEO VIDEOOUTPUTSWITCHANT INANT OUTANTENNA IN M.P.I.(            )(            )Wall JackAntenna12Connect the RF antenna out socket of theVCR to the AANNTTEENNNNAA  IINNsocket on theTV.Connect the antenna cable to the RFantenna in socket of the VCR.1. How to connect2. How to use■Set VCR output switch to 3 or 4 and thentune TV to the same channel number.■Insert a video tape into the VCR and pressPLAY on the VCR. (Refer to the VCR owner’smanual.)21Composite (RCA) ConnectionConnect the AAUUDDIIOO/VVIIDDEEOOjacks between TV andVCR. Match the jack colors (Video = yellow, Audio Left= white, and Audio Right = red)1. How to connect2. How to use■Insert a video tape into the VCR and press PLAY on theVCR. (Refer to the VCR owner’s manual.)■Select the AAVV11input source on the TV using the IINNPPUUTTbutton on the remote control.■If connected to AAVV  IINN  22, select AAVV22input source on the TV.1GGIf you have a mono VCR, connect the audio cablefrom the VCR to the AAUUDDIIOO  ((LL//MMOONNOO))jack ofthe TV.NOTE!L RS-VIDEO VIDEOAUDIOOUTPUTSWITCHANT INANT OUTVIDEOAUDIOCOMPONENT INL RVIDEO AUDIOL(MONO)RAV IN21/DVI INGAMECONTROL1
EXTERNAL EQUIPMENT SETUP26EXTERNAL EQUIPMENT SETUPOTHER A/V SOURCE SETUPAV IN 2L/MONORAUDIOVIDEOL RVIDEOUSB INCamcorderVideo Game SetConnect the AAUUDDIIOO/VVIIDDEEOOjacksbetween TV and external equipment.Match the jack colors.(Video = yellow, Audio Left = white, andAudio Right = red)1. How to connect2. How to use■Select the AAVV22input source on the TV using theIINNPPUUTTbutton on the remote control. ■If connected to AAVV  IINN  11input, select the AAVV11input source on the TV. ■Operate the corresponding external equipment.11
EXTERNAL EQUIPMENT SETUP27PC SETUP This TV provides Plug and Play capability, meaning that the PC adjusts automatically to the TV's settings. VGA (D-Sub 15 pin) ConnectionOORRRGB OUTPUTAUDIO21/DVI INAUDIO INRGB IN (PC)UPDATERESET(RGB/DVI)RS-232C IN(SERVICE ONLY)     REMOTECONTROL  OUTSPEAKER OUT(8    )122. How to use■Turn on the PC and the TV.■Select the RRGGBB--PPCCinput source on the TV using theIINNPPUUTTbutton on the remote control.Connect the VGA output of the PC to the RRGGBB  IINN((PPCC))  jack on the TV.Connect the PC audio output to the  AAUUDDIIOO  IINN((RRGGBB//DDVVII))jack on the TV.1. How to connect21DVI to HDMI ConnectionVIDEOAUDIOVIDEO AUDIOL(MONO)RAV IN 1COMPONENT INL RAUDIODVI OUTPUT21/DVI INAUDIO INUPDATERESET(RGB/DVI)RS-232C IN(SERVICE ONLY)SPEAKER OUTRGB IN (PC)     REMOTECONTROL  OUT(8    )122. How to use■Turn on the PC and the TV.■Select the HHDDMMII11  input source on the TV using theIINNPPUUTTbutton on the remote control.Connect the DVI output of the PC to the HHDDMMII//DDVVII  IINN11jack on the TV.Connect the PC audio output to the AAUUDDIIOOIINN((RRGGBB//DDVVII))  jack on the TV.1. How to connect21
EXTERNAL EQUIPMENT SETUP28EXTERNAL EQUIPMENT SETUPGGTo get the best picture quality, adjust the PC graphics card to 1360x768, 60Hz.GGDepending on the graphics card, DOS mode may not work if a HDMI to DVI Cable is in use.GGIn PC mode, there may be noise associated with the resolution, vertical pattern, contrast or brightness. Ifnoise is present, change the PC output to another resolution, change the refresh rate to another rate oradjust the brightness and contrast on the PICTURE menu until the picture is clear.NOTES!Supported Display Specifications(RGB-PC, HDMI-PC) Resolution 640x4801360x768640x350720x400800x6001024x768Horizontal Vertical Frequency(KHz)Frequency(Hz)31.469 70.0831.469 59.9431.469 70.0837.879 60.3148.363 60.0047.776 59.8747.720 59.79947.13 59.65When you use too long RGB-PC cable, there might be a noise on the screen.GGAvoid keeping a fixed image on the screen for a long period of time. The fixed image could become per-manently imprinted on the screen.GGThe synchronization input form for Horizontal and Vertical frequencies is separate.GGDepending on the graphics card, some resolution settings may not allow the image to be positioned onthe screen properly.1280x7681366x768Resolution 640x4801360x768640x350720x400800x6001024x768Horizontal Vertical Frequency(KHz)Frequency(Hz)31.468 70.0931.469 59.931.469 70.0835.156 56.2537.879 60.3148.363 60.0056.476 70.0647.776 59.87047.712 60.01563.981 60.02075.00 60.0066.587 59.9341280x7681280x1024(For 37/42LH260H)1600x12001920x1080
EXTERNAL EQUIPMENT SETUP33USB CONNECTIONUSB INAV IN 2L/MONORAUDIOVIDEOMemory KeyConnect the USB device to the UUSSBB  IINNjack on the sideof TV. 1. How to connect12. How to use■After connecting the UUSSBB  IINNjack, you use the USB func-tion. (GGpp..4433)1or
USB43USBWhen removing the USB deviceUSB INRMemory KeyConnect the USB device to the UUSSBB  IINNjacks on the side of TV. 3Select PPHHOOTTOO  LLIISSTTor MMUUSSIICCLLIISSTT. 1Press the  button before removing the USBdevice.2EJECT■This TV Supports on JPG and MP3. When you connect a USB device, this pop up menu is displayed automatically.When the Pop Up menu does not appear, you can select Photo List or Music List in the USB menu.On a USB device, you can not add a new folder or delete an existing folder.or■Image shown may differ from your TV.PHOTO LIST MUSIC LISTENTRY MODESENTER
USB44Precautions when using the USB deviceGGOnly a USB storage device is recognizable. GGIf the USB storage device is connected through a USB hub, the device is not recognizable.GGA USB storage device using an automatic recognition program may not be recognized.GGA USB storage device which uses its own driver may not be recognized.GGThe recognition speed of a USB storage device may depend on each device.GGIn case of a card reader, up to four memory cards are concurrently recognizable.GGPlease do not turn off the TV or unplug the USB device when the connected USB storage device is working.When such device is suddenly separated or unplugged, the stored files or the USB storage device may be dam-aged. GGOnly use a USB storage device which has normal music, image or movie files.GGPlease connect power to a USB storage device (over 0.5A) which requires an external power supply.  If not, thedevice may not be recognized.GGPlease connect a USB storage device with cable is offered by USB maker.  If connected with cable is not offeredby USB maker or an excessively long cable, the device may not be recognized.GGSome USB storage devices may not be supported or operate properly.GGFile alignment method of USB storage device is similar to Window XP and filename can recognize up to 100English characters.GGPlease backup important files because data on the USB device may be damaged. Data management is the con-sumer's responsibility and as a result, the manufacturer does not cover data damage.GGPlease use only a USB storage device which was formatted as a FAT32, NTFS file system provided with the Windowsoperating system. In case of a storage device formatted as a different utility programme which is not supported byWindows, it may not be recognized.GGData in a USB storage device cannot be deleted in the NTFS file system.GGIf your USB memory device has multiple partitions, or if you use a USB multi-card reader, you can use up to 4partitions or USB memory devices.GGThe recommended capacity is 1TB or less for a USB external hard disk and 32GB or less for USB memory.GGAny device with more than the recommended capacity may not work properly.GGIf a USB external hard disk with a "Energy Saving" function does not work, turn the hard disk off and on again to makeit work properly. Refer to the user manual of the application USB external hard disk.GGWhen using a USB HDD via the USB extensing cable, connect a support electric power source.
APPENDIX89TROUBLESHOOTINGAPPENDIXTThhee  ooppeerraattiioonn  ddooeess  nnoott  wwoorrkk  nnoorrmmaallllyy..TThhee  vviiddeeoo  ddooeess  nnoott  wwoorrkk..No picture &No soundNo or poor coloror poor picturePoor reception on some channelsLines or streaksin picturesNo picture when connecting HDMIHorizontal/vertical barsor picture shakingPicture appears slowly after switching onThe remote controldoesn’t workPower is suddenly turned off■Check to see if there is any object between the product and the remote controlcausing obstruction. Ensure you are pointing the remote control directly at the TV.■Ensure that the batteries are installed with correct polarity (+ to +, - to -).■Ensure that the correct remote operating mode is set: TV, VCR etc.■Install new batteries.■Is the sleep timer set?■Check the power control settings. Power interrupted.■TV will be automatically turned off, in case of no signal for 15 minutes.■Check whether the product is turned on.■Try another channel. The problem may be with the broadcast.■Is the power cord inserted into wall power outlet?■Check your antenna direction and/or location.■Test the wall power outlet, plug another product’s power cord into the outletwhere the product’s power cord was plugged in.■This is normal, the image is muted during the product startup process. Pleasecontact your service center, if the picture has not appeared after five minutes.■Adjust Color in menu option.■Keep a sufficient distance between the product and the VCR.■Try another channel. The problem may be with the broadcast.■Are the video cables installed properly?■Activate any function to restore the brightness of the picture. ■Check for local interference such as an electrical appliance or power tool.■Station or cable product experiencing problems, tune to another station.■Station signal is weak, reorient antenna to receive weaker station.■Check for sources of possible interference.■Check antenna (Change the direction of the antenna).■Check HDMI cable over version 1.3.The HDMI cables don’t support HDMI version 1.3, it cause flickers or no screendisplay. In this case use the latest cables that support HDMI version 1.3.*This feature is not available for all models.
APPENDIX90EErrrraattiicc  OOppeerraattiioonnInstaller menu setup ■Adjust Installer menu settings as required.PPoowweerrNo Power ■See troubleshooting flow chart.SSooffttwwaarree  PPrroobblleemmssCannot direct enter chan-nel number or “No Signal”appears■After 2-5-5 + MENU, only channels included in TV controller will appear. If chan-nel is available it can be added to channel scan, rescan channels. If it is not avail-able, the ‘No Signal’ message appears on the TV screen.NOTE!GGFor other problems not caused by the TV, refer to other devices’ operating guides.APPENDIXTThheerree  iiss  aa  pprroobblleemm  iinn  PPCC  mmooddee..  ((OOnnllyy  PPCC  mmooddee  aapppplliieedd))■Adjust resolution, horizontal frequency, or vertical frequency.■Check the input source.■Work the Auto configure or adjust clock, phase, or H/V position. (Option)■Check the signal cable.■Reinstall the PC video card.The signal is out of rangeScreen color is unstableor single colorVertical bar or stripe on background &Horizontal Noise &Incorrect positionPicture OK & No soundUnusual sound frominside the productNo sound when connecting HDMIor USBNo output from one of the speakersTThhee  aauuddiioo  ddooeess  nnoott  wwoorrkk..■Press the VOL or VOLUME button.■Sound muted? Press MUTE button.■Try another channel. The problem may be with the broadcast.■Are the audio cables installed properly?■Adjust Balance in menu option.■A change in ambient humidity or temperature may result in an unusual noisewhen the product is turned on or off and does not indicate a fault with theproduct.■Check HDMI cable over version 1.3.■Check USB cable over version 2.0.■Use normal MP3 file. *This feature is not available for all models.
APPENDIX91MAINTENANCE■The specifications shown above may be changed without prior notice for quality improvement.Early malfunctions can be prevented. Careful and regular cleaning can extend the amount of time you canenjoy your new TV. Caution: Be sure to turn the power off and unplug the power cord before you begin any cleaning.Cleaning the ScreenHere’s a great way to keep the dust off your screen for a while. Wet a soft cloth in a mixture of lukewarm water and alittle fabric softener or dish washing detergent. Wring the cloth until it’s almost dry, and then use it to wipe the screen.Make sure the excess water is off the screen, and then let it air-dry before you turn on your TV.GG  If you expect to leave your TV dormant for a long time (such as a vacation), it’s a good idea to unplugthe power cord to protect against possible damage from lightning or power surges.CAUTION21GGDo not use window/glass cleaner or anything with ammonia to clean the screen.WARNINGCleaning the Cabinet■To remove dirt or dust, wipe the cabinet with a soft, dry, lint-free cloth.■Please be sure not to use a wet cloth.Extended AbsenceMODELAC100-240V ~ 50/60HzNTSC-M, ATSC, 64 & 256 QAMVHF 2-13, UHF 14-69, CATV 1-135, DTV 2-69, CADTV 1-13575 ohm32 ~ 104°F (0 ~40°C)Less than 80%-4 ~ 140°F (-20 ~60°C)Less than 85%Dimensions(Width x Height x Depth)WeightPower requirementTelevision SystemProgram CoverageExternal Antenna ImpedanceEnvironment conditionWith standWithout standWith standWithout standOperating TemperatureOperating HumidityStorage TemperatureStorage Humidity42LH250H (42LH250H-UA)42LH255H (42LH255H-UA)42LH260H (42LH260H-UA)40.4 x 28.1 x 11.6 inches1028.0 x 715.4 x 297.0 mm40.4 x 25.7 x 3.4 inches1028.0 x 655.0 x 88.7 mm41.0 pounds / 18.6 kg37.0 pounds / 16.8 kg37LH250H (37LH250H-UA)37LH255H (37LH255H-UA)37LH260H (37LH260H-UA)36.2 x 25.9 x 11.6 inches922.0 x 659.0 x 297.0 mm36.2 x 23.4 x 3.4 inches922.0 x 595.0 x 88.0 mm33.0 pounds / 15.0 kg29.1 pounds / 13.2 kg32LH240H (32LH240H-UA)32LH250H (32LH250H-UA)32LH255H (32LH255H-UA)31.6 x 22.9 x 8.8 inches805.0 x 583.0 x 223.8 mm31.6 x 20.7 x 4.2 inches805.0 x 528.2 x 108.9 mm27.7 pounds / 12.6 kg25.1 pounds / 11.4 kgPRODUCT SPECIFICATIONS
APPENDIXAPPENDIX92IR CODES■Configuration of frame 1st frameRepeat frame■Lead code■Repeat code■BBiitt  ddeessccrriippttiioonn■FFrraammee  iinntteerrvvaall::  TTff  The waveform is transmitted as long as a key is depressed.C0 C1 C2 C3 C4 C5 C6 C7 C0 C1 C2 C3 C4 C5 C6 C7 D0 D1 D2 D3 D4 D5 D6 D7 D0 D1 D2 D3 D4 D5 D6 D7 Lead code Low custom code High custom code Data code  Data code Repeat  code Tf4.5 ms9 ms 2.25 ms 9 ms 0.55 ms 0.56 ms1.12 ms0.56 ms2.24 msTf TfTf=108ms @455KHzBit ”0”  Bit ”1”1. How to Connect■Connect your wired remote control to the Remote Control port on the TV. 2. Remote Control IR Codes■Output waveform Single pulse, modulated with 37.917KHz signal at 455KHz   T1TcCarrier frequencyFCAR = 1/TC = fOSC/12Duty ratio = T1/TC = 1/3
APPENDIX93Code Function Note(Hexa) Code Function Note(Hexa)D6 TV Discrete IR Code (TV Input Selection)5A AV1Discrete IR Code (AV1 Input Selection)D0 AV2 Discrete IR Code (AV2 Input Selection)BF COMPONENTDiscrete IR Code (COMPONENT Input Selection)D5 RGB-PCDiscrete IR Code (RGBInput Selection)CE HDMI1Discrete IR Code (HDMI1Input Selection)CC HDMI2 Discrete IR Code (HDMI2 Input Selection)76 Ratio 4:3Discrete IR Code (Only 4:3 Mode)77 Ratio 16:9Discrete IR Code (Only 16:9 Mode)AF Ratio ZoomDiscrete IR Code(Only Zoom1 Mode)C4 POWER ONDiscrete IR Code (Only  Power On)C5 POWER OFFDiscrete IR Code (Only Power Off)08 POWERRemote control Button (Power On/Off)0B INPUT Remote control Button1E MARK Remote control Button79 RATIO Remote control Button39 CC Remote control Button10-19 Number Key 0-9 Remote control Button4C - (Dash)/LIST Remote control Button1A FLASHBK Remote control Button02 VOL + Remote control Button03 VOL - Remote control Button00 CH Remote control Button01 CH Remote control Button0A SAP Remote control Button0E TIMER Remote control Button09 MUTE Remote control Button43 MENU Remote control Button5B RETURN Remote control ButtonE8 ALAM Remote control ButtonCA EJECT Remote control Button40 Remote control Button41 Remote control Button07 Remote control Button06 Remote control Button44 ENTER Remote control Button72 RED Remote control Button71 A (GREEN) Remote control Button63 G (YELLOW) Remote control Button61ll  ll(BLUE) Remote control Button8F FF Remote control Button8E GG Remote control Button
94OPEN SOURCE LICENSECopyright (C) 1989, 1991 Free Software Foundation, Inc., 51Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA Everyone is permitted to copy and distribute verbatim copies ofthis license document, but changing it is not allowed.PreambleThe licenses for most software are designed to take away yourfreedom to share and change it. By contrast, the GNU GeneralPublic License is intended to guarantee your freedom to shareand change free software - to make sure the software is free forall its users. This General Public License applies to most of theFree Software Foundation's software and to any other programwhose authors commit to using it. (Some other free softwarefoundation software is covered by the GNU Lesser General PublicLicense instead.) You can apply it to your programs, too.When we speak of free software, we are referring to freedom, notprice. Our General Public Licenses are designed to make sure thatyou have the freedom to distribute copies of free software (andcharge for this service if you wish), that you receive source codeor can get it if you want it, that you can change the software oruse pieces of it in new free programs; and that you know you cando these things.To protect your rights, we need to make restrictions that forbidanyone to deny you these rights or to ask you to surrender therights. These restrictions translate to certain responsibilities foryou if you distribute copies of the software, or if you modify it.For example, if you distribute copies of such a program, whethergratis or for a fee, you must give the recipients all the rights thatyou have. You must make sure that they, too, receive or can getthe source code. And you must show them these terms so theyknow their rights.We protect your rights with two steps: (1) copyright the soft-ware, and (2) offer you this license which gives you legal permis-sion to copy, distribute and/or modify the software.Also, for each author's protection and ours, we want to make cer-tain that everyone understands that there is no warranty for thisfree software. If the software is modified by someone else andpassed on, we want its recipients to know that what they have isnot the original, so that any problems introduced by others willnot reflect on the original authors' reputations.Finally, any free program is threatened constantly by softwarepatents. We wish to avoid the danger that redistributors of a freeprogram will individually obtain patent licenses, in effect makingthe program proprietary. To prevent this, we have made it clearthat any patent must be licensed for everyone's free use or notlicensed at all.The precise terms and conditions for copying, distribution andmodification follow.GNU GENERAL PUBLIC LICENSETERMS AND CONDITIONS FOR COPYING, DISTRIBUTIONAND MODIFICATION0. This license applies to any program or other work which con-tains a notice placed by the copyright holder saying it may bedistributed under the terms of this General Public License.  The"Program", below, refers to any such program or work, and a"work based on the Program" means either the Program or anyderivative work under copyright law: that is to say, a work con-taining the Program or a portion of it, either verbatim or withmodifications and/or translated into another language.(Hereinafter, translation is included without limitation in theterm "modification".)  Each licensee is addressed as "you".Activities other than copying, distribution and modificationare not covered by this license; they are outside its scope.The act of running the Program is not restricted, and the out-put from the program is covered only if its contents constitutea work based on the program (independent of having beenmade by running the program). Whether that is true dependson what the program does.1. You may copy and distribute verbatim copies of the program'ssource code as you receive it, in any medium, provided thatyou conspicuously and appropriately publish on each copy anappropriate copyright notice and disclaimer of warranty; keepintact all the notices that refer to this license and to theabsence of any warranty; and give any other recipients of theprogram a copy of this license along with the Program.You may charge a fee for the physical act of transferring acopy, and you may at your option offer warranty protection inexchange for a fee.2. You may modify your copy or copies of the program or anyportion of it, thus forming a work based on the Program, andcopy and distribute such modifications or work under theterms of section 1 above, provided that you also meet all ofthese conditions:a) You must cause the modified files to carry prominentnotices stating that you changed the files and the date ofany change.GNU GENERAL PUBLIC LICENSEVersion 2, June 1991
95b) You must cause any work that you distribute or publish,that in whole or in part contains or is derived from theProgram or any part there of, to be licensed as a whole atno charge to all third parties under the terms of thislicense.c) If the modified program normally reads commands interac-tively when run, you must cause it, when started runningfor such interactive use in the most ordinary way, to printor display an announcement including an appropriatecopyright notice and a notice that there is no warranty (orelse, saying that you provide a warranty) and that usersmay redistribute the program under these conditions, andtelling the user how to view a copy of this license.(Exception: if the Program itself is interactive but does notnormally print such an announcement, your work based onthe Program is not required to print an announcement.)These requirements apply to the modified work as a whole.  Ifidentifiable sections of that work are not derived from theProgram, and can be reasonably considered independent andseparate works in themselves, then this license, and its terms,do not apply to those sections when you distribute them asseparate works. But when you distribute the same sections aspart of a whole which is a work based on the Program, the dis-tribution of the whole must be on the terms of this license,whose permissions for other licensees extend to the entirewhole, and thus to each and every part regardless of whowrote it.Thus, it is not the intent of this section to claim rights or con-test your rights to work written entirely by you; rather, theintent is to exercise the right to control the distribution ofderivative or collective works based on the program.In addition, mere aggregation of another work not based onthe program with the Program (or with a work based on theprogram) on a volume of a storage or distribution mediumdoes not bring the other work under the scope of this license.3. You may copy and distribute the program (or a work based onit, under section 2) in object code or executable form underthe terms of sections 1 and 2 above provided that you alsodo one of the following:a) Accompany it with the complete corresponding machine-readable source code, which must be distributed under theterms of sections 1 and 2 above on a medium customarilyused for software interchange; or,b) Accompany it with a written offer, valid for at least threeyears, to give any third party, for a charge no more thanyour cost of physically performing source distribution, acomplete machine-readable copy of the correspondingsource code, to be distributed under the terms of sections1 and 2 above on a medium customarily used for softwareinterchange; or,c) Accompany it with the information you received as to theoffer to distribute corresponding source code. (This alter-native is allowed only for noncommercial distribution andonly if you received the program in object code or exe-cutable form with such an offer, in accord with Subsectionb above.)The source code for a work means the preferred form of thework for making modifications to it.  For an executable work,complete source code means all the source code for all mod-ules it contains, plus any associated interface definition files,plus the scripts used to control compilation and installationof the executable. However, as a special exception, the sourcecode distributed need not include anything that is normallydistributed (in either source or binary form) with the majorcomponents (compiler, kernel, and so on) of the operatingsystem on which the executable runs, unless that componentitself accompanies the executable.If distribution of executable or object code is made by offer-ing access to copy from a designated place, then offeringequivalent access to copy the source code from the sameplace counts as distribution of the source code, even thoughthird parties are not compelled to copy the source along withthe object code.4. You may not copy, modify, sublicense, or distribute the Programexcept as expressly provided under this license.  Any attemptotherwise to copy, modify, sublicense or distribute theProgram is void, and will automatically terminate your rightsunder this license. However, parties who have received copies,or rights, from you under this license will not have their licens-es terminated so long as such parties remain in full compli-ance.5. You are not required to accept this license, since you have notsigned it. However, nothing else grants you permission tomodify or distribute the Program or its derivative works.These actions are prohibited by law if you do not  accept thislicense. Therefore, by modifying or distributing the program(or any work based on the program), you indicate your accep-tance of this license to do so, and all its terms and conditionsfor copying, distributing or modifying the program or worksbased on it.6. Each time you redistribute the program (or any work based onthe Program), the recipient automatically receives a licensefrom the original licensor to copy, distribute or modify theProgram subject to these terms and conditions. You may notimpose any further restrictions on the recipients' exercise ofthe rights granted herein. You are not responsible for enforc-ing compliance by third parties to this license.
APPENDIXAPPENDIX967. If, as a consequence of a court judgment or allegation ofpatent infringement or for any other reason (not limited topatent issues), conditions are imposed on you (whether bycourt order, agreement or otherwise) that contradict the con-ditions of this license, they do not excuse you from the con-ditions of this license. If you cannot distribute so as to satis-fy simultaneously your obligations under this license and anyother pertinent obligations, then as a consequence you maynot distribute the program at all. For example, if a patentlicense would not permit royalty-free redistribution of theprogram by all those who receive copies directly or indirectlythrough you, then the only way you could satisfy both it andthis license would be to refrain entirely from distribution ofthe program.If any portion of this section is held invalid or unenforceableunder any particular circumstance, the balance of the sectionis intended to apply and the section as a whole is intended toapply in other circumstances.It is not the purpose of this section to induce you to infringeany patents or other property right claims or to contest valid-ity of any such claims; this section has the sole purpose ofprotecting the integrity of the free software distribution sys-tem, which is implemented by public license practices. Manypeople have made generous contributions to the wide rangeof software distributed through that system in reliance onconsistent application of that system; it is up to theauthor/donor to decide if he or she is willing to distributesoftware through any other system and a licensee cannotimpose that choice.This section is intended to make thoroughly clear what isbelieved to be a consequence of the rest of this license.8. If the distribution and/or use of the program is restricted incertain countries either by patents or by copyrighted inter-faces, the original copyright holder who places the programunder this license may add an explicit geographical distributionlimitation excluding those countries, so that distribution ispermitted only in or among countries not thus excluded. Insuch case, this license incorporates the limitation as if writtenin the body of this license.9. The Free Software Foundation may publish revised and/ornew versions of the General Public License from time to time.Such new versions will be similar in spirit to the present ver-sion, but may differ in detail to address new problems or con-cerns.Each version is given a distinguishing version number.  If theprogram specifies a version number of this license whichapplies to it and "any later version", you have the option offollowing the terms and conditions either of that version or ofany later version published by the Free Software Foundation.If the program does not specify a version number of thislicense, you may choose any version ever published by theFree Software Foundation.10.If you wish to incorporate parts of the program into other freeprograms whose distribution conditions are different, write tothe author to ask for permission.  For software which is copy-righted by the Free Software Foundation, write to the FreeSoftware Foundation; we sometimes make exceptions for this.Our decision will be guided by the two goals of preserving thefree status of all derivatives of our free software and of pro-moting the sharing and reuse of software generally.NO WARRANTY11. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE,THERE IS NO WARRANTY FOR THE PROGRAM, TO THEEXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHENOTHERWISE STATED IN WRITING THE COPYRIGHT HOLD-ERS AND/OR OTHER PARTIES PROVIDE THE PROGRAM "ASIS" WITHOUT WARRANTY OF ANY KIND, EITHEREXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITEDTO, THE IMPLIED WARRANTIES OF MERCHANTABILITYAND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRERISK AS TO THE QUALITY AND PERFORMANCE OF THEPROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVEDEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARYSERVICING, REPAIR OR CORRECTION.12.IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW ORAGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER,OR ANY OTHER PARTY WHO MAY MODIFY AND/ORREDISTRIBUTE THE PROGRAM AS PERMITTED ABOVE, BELIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL,SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGESARISING OUT OF THE USE OR INABILITY TO USE THE PRO-GRAM (INCLUDING BUT NOT LIMITED TO LOSS OF DATAOR DATA BEING RENDERED INACCURATE OR LOSSES SUS-TAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THEPROGRAM TO OPERATE WITH ANY OTHER PROGRAMS),EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEENADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
APPENDIX97END OF TERMS AND CONDITIONSHow to apply these terms to your new programsIf you develop a new program, and you want it to be of the great-est possible use to the public, the best way to achieve this is tomake it free software which everyone can redistribute and changeunder these terms.To do so, attach the following notices to the program.  It is safestto attach them to the start of each source file to most effective-ly convey the exclusion of warranty; and each file should have atleast the "copyright" line and a pointer to where the full notice isfound.one line to give the program's name and a brief idea of what itdoes.Copyright (C) <year>  <name of author>This program is free software; you can redistribute it and/ormodify it under the terms of the GNU General Public License aspublished by the Free Software Foundation; either version 2 ofthe license, or (at your option) any later version. This program is distributed in the hope that it will be useful, butWITHOUT ANY WARRANTY; without even the implied warrantyof MERCHANTABILITY or FITNESS FOR A PARTICULAR PUR-POSE.  See the GNU General Public License for more details.You should have received a copy of the GNU General PublicLicense along with this program; if not, write to the Free SoftwareFoundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA02110-1301 USA.Also add information on how to contact you by electronic andpaper mail.If the program is interactive, make it output a short notice likethis when it starts in an interactive mode:Gnomovision version 69, Copyright (C) year name of authorGnomovision comes with ABSOLUTELY NO WARRANTY; fordetails type ‘show w’. This is free software, and you are welcometo redistribute it under certain conditions; type ‘show c’ fordetails.The hypothetical commands ‘show w’ and ‘show c’ should showthe appropriate parts of the General Public License. Of course,the commands you use may be called something other than‘show w’ and ‘show c’; they could even be mouse-clicks or menuitems-whatever suits your program.You should also get your employer (if you work as a programmer)or your school, if any, to sign a “copyright disclaimer” for the pro-gram, if necessary.  Here is a sample; alter the names:Yoyodyne, Inc., hereby disclaims all copyright interest in the pro-gram ‘Gnomovision’ (which makes passes at compilers) written byJames Hacker.signature of Ty Coon, 1 April 1989Ty Coon, President of ViceThis General Public License does not permit incorporating yourprogram into proprietary programs. If your program is a subrou-tine library, you may consider it more useful to permit linking pro-prietary applications with the library. If this is what you want todo, use the GNU Lesser General Public License instead of thislicense.
98Copyright (C) 1991, 1999 Free Software Foundation, Inc.  51Franklin Street, Fifth Floor, Boston, MA  02110-1301  USAEveryone is permitted to copy and distribute verbatim copies  ofthis license document, but changing it is not allowed.[This is the first released version of the Lesser GPL.  It alsocounts  as the successor of the GNU Library Public License, ver-sion 2, hence  the version number 2.1.]PreambleThe licenses for most software are designed to take away yourfreedom to share and change it. By contrast, the GNU GeneralPublic Licenses are intended to guarantee your freedom to shareand change free software - to make sure the software is free forall its users.This license, the Lesser General Public License, applies to somespecially designated software packages - typically libraries - ofthe Free Software Foundation and other authors who decide touse it. You can use it too, but we suggest you first think careful-ly about whether this license or the ordinary General PublicLicense is the better strategy to use in any particular case, basedon the explanations below.When we speak of free software, we are referring to freedom ofuse, not price. Our General Public Licenses are designed to makesure that you have the freedom to distribute copies of free soft-ware (and charge for this service if you wish); that you receivesource code or can get it if you want it; that you can change thesoftware and use pieces of it in new free programs; and that youare informed that you can do these things.To protect your rights, we need to make restrictions that forbiddistributors to deny you these rights or to ask you to surrenderthese rights. These restrictions translate to certain responsibilitiesfor you if you distribute copies of the library or if you modify it.For example, if you distribute copies of the library, whether gratisor for a fee, you must give the recipients all the rights that wegave you. You must make sure that they, too, receive or can getthe source code. If you link other code with the library, you mustprovide complete object files to the recipients, so that they canrelink them with the library after making changes to the libraryand recompiling it. And you must show them these terms so theyknow their rights.We protect your rights with a two-step method: (1) we copyrightthe library, and (2) we offer you this license, which gives you legalpermission to copy, distribute and/or modify the library.To protect each distributor, we want to make it very clear thatthere is no warranty for the free library. Also, if the library is mod-ified by someone else and passed on, the recipients should knowthat what they have is not the original version, so that the origi-nal author's reputation will not be affected by problems thatmight be introduced by others.Finally, software patents pose a constant threat to the existenceof any free program.  We wish to make sure that a company can-not effectively restrict the users of a free program by obtaining arestrictive license from a patent holder. Therefore, we insist thatany patent license obtained for a version of the library must beconsistent with the full freedom of use specified in this license.Most GNU software, including some libraries, is covered by theordinary GNU General Public License. This license, the GNULesser General Public License, applies to certain designatedlibraries, and is quite different from the ordinary General PublicLicense. We use this license for certain libraries in order to per-mit linking those libraries into non-free programs.When a program is linked with a library, whether statically orusing a shared library, the combination of the two is legallyspeaking a combined work, a derivative of the original library. Theordinary General Public License therefore permits such linkingonly if the entire combination fits its criteria of freedom. TheLesser General Public License permits more lax criteria for linkingother code with the library.We call this license the "Lesser" General Public License becauseit does Less to protect the user's freedom than the ordinaryGeneral Public License. It also provides other free software devel-opers Less of an advantage over competing non-free programs.These disadvantages are the reason we use the ordinary GeneralPublic License for many libraries. However, the Lesser license pro-vides advantages in certain special circumstances.For example, on rare occasions, there may be a special need toencourage the widest possible use of a certain library, so that itbecomes a de-facto standard. To achieve this, non-free programsmust be allowed to use the library. A more frequent case is thata free library does the same job as widely used non-free libraries.In this case, there is little to gain by limiting the free library to freesoftware only, so we use the Lesser General Public License.In other cases, permission to use a particular library in non-freeprograms enables a greater number of people to use a large bodyof free software. For example, permission to use the GNU CLibrary in non-free programs enables many more people to usethe whole GNU operating system, as well as its variant, theGNU/Linux operating system.GNU LESSER GENERAL PUBLIC LICENSEVersion 2.1, February 1999
99Although the Lesser General Public License is Less protective ofthe users' freedom, it does ensure that the user of a program thatis linked with the Library has the freedom and the wherewithal torun that program using a modified version of the Library.The precise terms and conditions for copying, distribution andmodification follow. Pay close attention to the difference betweena "work based on the library" and a "work that uses the library".The former contains code derived from the library, whereas thelatter must be combined with the library in order to run.GNU LESSER GENERAL PUBLIC LICENSETERMS AND CONDITIONS FOR COPYING, DISTRIBUTIONAND MODIFICATION0. This license agreement applies to any software library or otherprogram which contains a notice placed by the copyright hold-er or other authorized party saying it may be distributedunder the terms of this Lesser General Public License (alsocalled “this license”). Each license is addressed as "you".A “library” means a collection of software functions and/ordata prepared so as to be conveniently linked with applicationprograms (which use some of those functions and data) toform executables.The “Library”, below, refers to any such software library or workwhich has been distributed under these terms. A “work basedon the Library” means either the Library or any derivative workunder copyright law: that is to say, a work containing thelibrary or a portion of it, either verbatim or with modificationsand/or translated straightforwardly into another language.(Hereinafter, translation is included without limitation in theterm “modification”.)“Source code” for a work means the preferred form of thework for making modifications to it. For a library, completesource code means all the source code for all modules it con-tains, plus any associated interface definition files, plus thescripts used to control compilation and installation of thelibrary.Activities other than copying, distribution and modificationare not covered by this license; they are outside its scope.The act of running a program using the Library is not restrict-ed, and output from such a program is covered only if its con-tents constitute a work based on the library (independent ofthe use of the Library in a tool for writing it). Whether that istrue depends on what the library does and what the programthat uses the library does.1. You may copy and distribute verbatim copies of the library'scomplete source code as you receive it, in any medium, pro-vided that you conspicuously and appropriately publish oneach copy an appropriate copyright notice and disclaimer ofwarranty; keep intact all the notices that refer to this licenseand to the absence of any warranty; and distribute a copy ofthis license along with the Library.You may charge a fee for the physical act of transferring acopy, and you may at your option offer warranty protection inexchange for a fee.2. You may modify your copy or copies of the Library or anyportion of it, thus forming a work based on the Library, andcopy and distribute such modifications or work under theterms of section 1 above, provided that you also meet all ofthese conditions:a) The modified work must itself be a software library.b) You must cause the files modified to carry prominentnotices stating that you changed the files and the date ofany change.c) You must cause the whole of the work to be licensed at nocharge to all third parties under the terms of this license.d) If a facility in the modified Library refers to a function or atable of data to be supplied by an application program thatuses the facility, other than as an argument passed whenthe facility is invoked, then you must make a good faitheffort to ensure that, in the event an application does notsupply such function or table, the facility still operates, andperforms whatever part of its purpose remains meaningful.(For example, a function in a library to compute square rootshas a purpose that is entirely well-defined independent of theapplication.  Therefore, Subsection 2d requires that any appli-cation-supplied function or table used by this function must beoptional: if the application does not supply it, the square rootfunction must still compute square roots.)These requirements apply to the modified work as a whole.  Ifidentifiable sections of that work are not derived from thelibrary, and can be reasonably considered independent andseparate works in themselves, then this license, and its terms,do not apply to those sections when you distribute them asseparate works.  But when you distribute the same sections aspart of a whole which is a work based on the library, the dis-tribution of the whole must be on the terms of this license,whose permissions for other licenses extend to the entirewhole, and thus to each and every part regardless of whowrote it.Thus, it is not the intent of this section to claim rights or con-test your rights to work written entirely by you; rather, theintent is to exercise the right to control the distribution ofderivative or collective works based on the library.In addition, mere aggregation of another work not based onthe library with the library (or with a work based on thelibrary) on a volume of a storage or distribution medium doesnot bring the other work under the scope of this license.
1003. You may opt to apply the terms of the ordinary GNU GeneralPublic License instead of this License to a given copy of theLibrary.  To do this, you must alter all the notices that refer tothis License, so that they refer to the ordinary GNU GeneralPublic License, version 2, instead of to this License. (If a newerversion than version 2 of the ordinary GNU General PublicLicense has appeared, then you can specify that versioninstead if you wish.) Do not make any other change in thesenotices.Once this change is made in a given copy, it is irreversible forthat copy, so the ordinary GNU General Public License appliesto all subsequent copies and derivative works made from thatcopy.This option is useful when you wish to copy part of the codeof the library into a program that is not a library.4. You may copy and distribute the library (or a portion or deriv-ative of it, under Section 2) in object code or executable formunder the terms of Sections 1 and 2 above provided that youaccompany it with the complete corresponding machine-readable source code, which must be distributed under theterms of sections 1 and 2 above on a medium customarilyused for software interchange.If distribution of object code is made by offering access tocopy from a designated place, then offering equivalent accessto copy the source code from the same place satisfies therequirement to distribute the source code, even though thirdparties are not compelled to copy the source along with theobject code.5. A program that contains no derivative of any portion of theLibrary, but is designed to work with the Library by beingcompiled or linked with it, is called a “work that uses theLibrary”. Such a work, in isolation, is not a derivative work ofthe Library, and therefore falls outside the scope of thislicense.However, linking a “work that uses the library” with the Librarycreates an executable that is a derivative of the Library(because it contains portions of the library), rather than a“work that uses the library”. The executable is therefore cov-ered by this license. Section 6 states terms for distribution ofsuch executable.When a “work that uses the library” uses material from a head-er file that is part of the library, the object code for the workmay be a derivative work of the library even though the sourcecode is not.Whether this is true is especially significant if the work can belinked without the library, or if the work is itself a library. Thethreshold for this to be true is not precisely defined by law.If such an object file uses only numerical parameters, datastructure layouts and accessories, and small macros and smallinline functions (ten lines or less in length), then the use ofthe object file is unrestricted, regardless of whether it is legal-ly a derivative work.  (Executable containing this object codeplus portions of the library will still fall under Section 6.)Otherwise, if the work is a derivative of the library, you maydistribute the object code for the work under the terms ofSection 6. Any executable containing that work also fall underSection 6, whether or not they are linked directly with thelibrary itself.6. As an exception to the sections above, you may also combineor link a "work that uses the library" with the library to pro-duce a work containing portions of the library, and distributethat work under terms of your choice, provided that the termspermit modification of the work for the customer's own useand reverse engineering for debugging such modifications.You must give prominent notice with each copy of the workthat the library is used in it and that the Library and its useare covered by this license. You must supply a copy of thislicense. If the work during execution displays copyrightnotices, you must include the copyright notice for the libraryamong them, as well as a reference directing the user to thecopy of this license. Also, you must do one of these things:a) Accompany the work with the complete correspondingmachine-readable source code for the library includingwhatever changes were used in the work (which must bedistributed under Sections 1 and 2 above); and, if the workis an executable linked with the Library, with the completemachine-readable “work that uses the Library”, as objectcode and/or source code, so that the user can modify thelibrary and then relink to produce a modified executablecontaining the modified library.  (It is understood that theuser who changes the contents of definitions files in thelibrary will not necessarily be able to recompile the appli-cation to use the modified definitions.)b) Use a suitable shared library mechanism for linking with thelibrary. A suitable mechanism is one that (1) uses at run timea copy of the library already present on the user’s computersystem, rather than copying library functions into the exe-cutable, and (2) will operate properly with a modified versionof the library, if the user installs one, as long as the modifiedversion is interface-compatible with the version that thework was made with.c) Accompany the work with a written offer, valid for at leastthree years, to give the same user the materials specified inSubsection 6, above, for a charge no more than the cost ofperforming this distribution.d) If distribution of the work is made by offering access tocopy from a designated place, offer equivalent access tocopy the above specified materials from the same place.e) Verify that the user has already received a copy of thesematerials or that you have already sent this user a copy.
101For an executable, the required form of the "work that usesthe library" must include any data and utility programs need-ed for reproducing the executable from it.  However, as a spe-cial exception, the materials to be distributed need notinclude anything that is normally distributed (in either sourceor binary form) with the major components (compiler, kernel,and so on) of the operating system on which the executableruns, unless that component itself accompanies the exe-cutable.It may happen that this requirement contradicts the licenserestrictions of other proprietary libraries that do not normal-ly accompany the operating system.  Such a contradictionmeans you cannot use both them and the library together inan executable that you distribute.7. You may place library facilities that are a work based on thelibrary side-by-side in a single library together with otherlibrary facilities not covered by this license, and distributesuch a combined library, provided that the separate distribu-tion of the work based on the Library and of the other libraryfacilities is otherwise permitted, and provided that you dothese two things:a) Accompany the combined library with a copy of the samework based on the Library, uncombined with any otherlibrary facilities. This must be distributed under the termsof the sections above.b) Give prominent notice with the combined library of thefact that part of it is a work based on the library, andexplaining where to find the accompanying uncombinedform of the same work.8. You may not copy, modify, sublicense, link with, or distributethe library except as expressly provided under this license.Any attempt otherwise to copy, modify, sublicense, link with,or distribute the library is void, and will automatically termi-nate your rights under this license.  However, parties who havereceived copies, or rights, from you under this license will nothave their licenses terminated so long as such parties remainin full compliance.9. You are not required to accept this license, since you have notsigned it. However, nothing else grants you permission to mod-ify or distribute the library or its derivative works.  Theseactions are prohibited by law if you do not accept this license.Therefore, by modifying or distributing the library (or any workbased on the library), you indicate your acceptance of thislicense to do so, and all its terms and conditions for copying,distributing or modifying the library or works based on it. 10.Each time you redistribute the library (or any work based onthe Library), the recipient automatically receives a licensefrom the original licensor to copy, distribute, link with or mod-ify the library subject to these terms and conditions.  You maynot impose any further restrictions on the recipients' exerciseof the rights granted herein.You are not responsible for enforcing compliance by thirdparties with this license.11. If, as a consequence of a court judgment or allegation ofpatent infringement or for any other reason (not limited topatent issues), conditions are imposed on you (whether bycourt order, agreement or otherwise) that contradict the con-ditions of this license, they do not excuse you from the con-ditions of this license. If you cannot distribute so as to satis-fy simultaneously your obligations under this license and anyother pertinent obligations, then as a consequence you maynot distribute the library at all. For example, if a patent licensewould not permit royalty-free redistribution of the library byall those who receive copies directly or indirectly throughyou, then the only way you could satisfy both it and thislicense would be to refrain entirely from distribution of thelibrary.If any portion of this section is held invalid or unenforceableunder any particular circumstance, the balance of the sectionis intended to apply, and the section as a whole is intended toapply in other circumstances.It is not the purpose of this section to induce you to infringeany patents or other property right claims or to contest valid-ity of any such claims; this section has the sole purpose ofprotecting the integrity of the free software distribution sys-tem which is implemented by public license practices. Manypeople have made generous contributions to the wide rangeof software distributed through that system in reliance onconsistent application of that system; it is up to theauthor/donor to decide if he or she is willing to distributesoftware through any other system and a license cannotimpose that choice.This section is intended to make thoroughly clear what isbelieved to be a consequence of the rest of this license.12.If the distribution and/or use of the library is restricted in cer-tain countries either by patents or by copyrighted interfaces,the original copyright holder who places the library under thislicense may add an explicit geographical distribution limitationexcluding those countries, so that distribution is permittedonly in or among countries not thus excluded. In such case,this license incorporates the limitation as if written in the bodyof this license.13.The Free Software Foundation may publish revised and/ornew versions of the Lesser General Public License from time totime. Such new versions will be similar in spirit to the presentversion, but may differ in detail to address new problems orconcerns.Each version is given a distinguishing version number.  If thelibrary specifies a version number of this license which appliesto it and “any later version”, you have the option of followingthe terms and conditions either of that version or of any laterversion published by the Free Software Foundation.
102If the library does not specify a license version number, youmay choose any version ever published by the Free SoftwareFoundation.14.If you wish to incorporate parts of the library into other freeprograms whose distribution conditions are incompatible withthese, write to the author to ask for permission.  For softwarewhich is copyrighted by the Free Software Foundation, writeto the Free Software Foundation; we sometimes make excep-tions for this.  Our decision will be guided by the two goals ofpreserving the free status of all derivatives of our free softwareand of promoting the sharing and reuse of software generally.NO WARRANTY15.BECAUSE THE LIBRARY IS LICENSED FREE OF CHARGE,THERE IS NO WARRANTY FOR THE LIBRARY, TO THEEXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHENOTHERWISE STATED IN WRITING THE COPYRIGHT HOLD-ERS AND/OR OTHER PARTIES PROVIDE THE LIBRARY "ASIS" WITHOUT WARRANTY OF ANY KIND, EITHEREXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITEDTO, THE IMPLIED WARRANTIES OF MERCHANTABILITYAND FITNESS FOR A PARTICULAR PURPOSE.  THE ENTIRERISK AS TO THE QUALITY AND PERFORMANCE OF THELIBRARY IS WITH YOU.  SHOULD THE LIBRARY PROVEDEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARYSERVICING, REPAIR OR CORRECTION.16.IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW ORAGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER,OR ANY OTHER PARTY WHO MAY MODIFY AND/ORREDISTRIBUTE THE LIBRARY AS PERMITTED ABOVE, BELIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL,SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGESARISING OUT OF THE USE OR INABILITY TO USE THELIBRARY (INCLUDING BUT NOT LIMITED TO LOSS OF DATAOR DATA BEING RENDERED INACCURATE OR LOSSES SUS-TAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THELIBRARY TO OPERATE WITH ANY OTHER SOFTWARE),EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEENADVISED OF THE POSSIBILITY OF SUCH DAMAGES.END OF TERMS AND CONDITIONSHow to apply these terms to your new librariesIf you develop a new library, and you want it to be of the great-est possible use to the public, we recommend making it free soft-ware that everyone can redistribute and change. You can do soby permitting redistribution under these terms (or, alternatively,under the terms of the ordinary General Public License).To apply these terms, attach the following notices to the library.It is safest to attach them to the start of each source file to mosteffectively convey the exclusion of warranty; and each file shouldhave at least the “copyright” line and a pointer to where the fullnotice is found.one line to give the library's name and a brief idea of what it does.Copyright (C) <year>  <name of author>This library is free software; you can redistribute it and/or modifyit under the terms of the GNU Lesser General Public License aspublished by the Free Software Foundation; either version 2.1 ofthe license, or (at your option) any later version.This library is distributed in the hope that it will be useful, butWITHOUT ANY WARRANTY; without even the implied warrantyof MERCHANTABILITY or FITNESS FOR A PARTICULAR PUR-POSE. See the GNU Lesser General Public License for moredetails.You should have received a copy of the GNU Lesser GeneralPublic License along with this library; if not, write to the FreeSoftware Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,MA  02110-1301  USA Also add information on how to contact you by electronic andpaper mail.You should also get your employer (if you work as a programmer)or your school, if any, to sign a “copyright disclaimer” for thelibrary, if necessary. Here is a sample; alter the names:Yoyodyne, Inc., hereby disclaims all copyright interest in thelibrary ‘Frob’ (a library for tweaking knobs) written by JamesRandom Hacker.signature of Ty Coon, 1 April 1990Ty Coon, President of Vice
1031.Definitions.1.0.1. “Commercial use” means distribution or otherwise makingthe covered code available to a third party.1.1. “Contributor” means each entity that creates or con-tributes to the creation of modifications.1.2. “Contributor version” means the combination of the orig-inal code, prior modifications used by a contributor, andthe modifications made by that particular contributor.1.3. “Covered code” means the original code or modificationsor the combination of the original code and modifications,in each case including portions thereof.1.4. “Electronic distribution mechanism” means a mechanismgenerally accepted in the software development communi-ty for the electronic transfer of data.1.5. “Executable” means covered code in any form other thansource code.1.6. “Initial developer” means the individual or entity identifiedas the initial Developer in the Source Code notice requiredby exhibit A.1.7. “Larger work” means a work which combines covered codeor portions thereof with code not governed by the termsof this License.1.8. “License” means this document.1.8.1. “Licensable” means having the right to grant, to the maxi-mum extent possible, whether at the time of the initialgrant or subsequently acquired, any and all of the rightsconveyed herein.1.9. “Modifications” means any addition to or deletion fromthe substance or structure of either the original code orany previous modifications. When covered code isreleased as a series of files, a modification is:A. Any addition to or deletion from the contents of a filecontaining original code or previous modifications.B. Any new file that contains any part of the original codeor previous modifications.1.10. “Original code” means source code of computer softwarecode which is described in the source code noticerequired by exhibit as original code, and which, at the timeof its release under this license is not already coveredcode governed by this license.1.10.1.“Patent claims” means any patent claim(s), now owned orhereafter acquired, including without limitation, method,process, and apparatus claims, in any patent licensable bygrantor.1.11. “Source code” means the preferred form of the coveredcode for making modifications to it, including all modulesit contains, plus any associated interface definition files,scripts used to control compilation and installation of anexecutable, or source code differential comparisonsagainst either the original code or another well known,available covered code of the contributor's choice. Thesource code can be in a compressed or archival form, pro-vided the appropriate decompression or de-archiving soft-ware is widely available for no charge.1.12. “You” (or “Your”) means an individual or a legal entityexercising rights under, and complying with all of the termsof, this license or a future version of this license issuedunder section 6.1.For legal entities, “You” includes any entity which controls,is controlled by, or is under common control with You. Forpurposes of this definition, “control” means (a) the power,direct or indirect, to cause the direction or management ofsuch entity, whether by contract or otherwise, or (b) own-ership of more than fifty percent (50%) of the outstand-ing shares or beneficial ownership of such entity.2. Source Code License.2.1. The initial developer grant.The initial developer hereby grants You a world-wide, roy-alty-free, non-exclusive license, subject to third party intel-lectual property claims:a) under intellectual property rights (other than patent ortrademark) licensable by initial developer to use, repro-duce, modify, display, perform, sublicense and distrib-ute the original code (or portions thereof) with or with-out modifications, and/or as part of a larger work; and(b) under patents claims infringed by the making, using orselling of original code, to make, have made, use, prac-tice, sell, and offer for sale, and/or otherwise disposeof the original code (or portions there of).MOZILLA PUBLIC LICENSEVersion 1.1---------------
104(c) the licenses granted in this section 2.1(a) and (b) areeffective on the date Initial developer first distributesoriginal code under the terms of this license.(d) Notwithstanding section 2.1(b) above, no patentlicense is granted: 1) for code that You delete from theoriginal Code; 2) separate from the original code;  or3) for infringements caused by: i) the modification ofthe original code or ii) the combination of the originalcode with other software or devices.2.2. Contributor Grant.Subject to third party intellectual property claims, eachcontributor hereby grants You a world-wide, royalty-free,non-exclusive license(a) under intellectual property rights (other than patentor trademark) licensable by contributor, to use,reproduce, modify, display, perform, sublicense anddistribute the modifications created by such contribu-tor (or portions thereof) either on an unmodifiedbasis, with other modifications, as covered codeand/or as part of a larger work; and(b) under patent claims infringed by the making, using, orselling of  modifications made by that contributoreither alone and/or in combination with its contributorversion (or portions of such combination), to make,use, sell, offer for sale, have made, and/or otherwisedispose of: 1) modifications made by that contributor(or portions thereof); and 2) the combination of mod-ifications made by that contributor with its contributorversion (or portions of such combination).(c) the licenses granted in sections 2.2(a) and 2.2(b) areeffective on the date contributor first makes commer-cial use of the covered code.(d) Notwithstanding section 2.2(b) above, no patentlicense is granted: 1) for any code that contributor hasdeleted from the contributor version; 2) separate fromthe contributor version; 3) for infringements causedby: i) third party modifications of contributor versionor ii)  the combination of modifications made by thatcontributor with other software (except as part of thecontributor version) or other devices; or 4) underpatent claims infringed by covered code in theabsence of modifications made by that contributor.3. Distribution Obligations.3.1. Application of license.The modifications which You create or to which you con-tribute are governed by the terms of this license, includingwithout limitation section 2.2. The source code version ofcovered code may be distributed only under the terms ofthis license or a future version of this license releasedunder section 6.1, and you must include a copy of thislicense with every copy of the source code you distribute.You may not offer or impose any terms on any source codeversion that alters or restricts the applicable version ofthis license or the recipients' rights hereunder. However,you may include an additional document offering theadditional rights described in section 3.5.3.2. Availability of source code.Any modification which you create or to which you con-tribute must be  made available in source code form underthe terms of this license either on the same media as anexecutable version or via an accepted electronic distribu-tion mechanism to anyone to whom you made an exe-cutable version available; and if made available via elec-tronic distribution mechanism, must remain available for atleast twelve (12) months after the date it initially becameavailable, or at least six (6) months after a subsequentversion of that particular modification has been madeavailable to such recipients. You are responsible for ensur-ing that the source code version remains available even ifthe electronic distribution mechanism is maintained by athird party.3.3. Description of modifications.You must cause all covered code to which you contribute tocontain a file documenting the changes You made to createthat covered code and the date of any change. You mustinclude a prominent statement that the modification isderived, directly or indirectly, from original code provided bythe initial developer and including the name of the    initialdeveloper in (a) the source code, and (b) in any notice in anexecutable version or related documentation in which youdescribe the origin or ownership of the covered code.3.4. Intellectual property matters(a) Third party claims.If contributor has knowledge that a license under a thirdparty's intellectual property rights is required to exercisethe rights granted by such contributor under sections 2.1or 2.2, contributor must include a text file with the sourcecode distribution titled "LEGAL" which describes the claimand the party making the claim in sufficient detail that arecipient will know whom to contact. If contributor obtainssuch knowledge after the modification is made available asdescribed in section 3.2, contributor shall promptly modi-fy the LEGAL file in all copies contributor makes availablethereafter and shall take other steps (such as notifyingappropriate mailing lists or newsgroups) reasonably calcu-lated to inform those who received the covered code thatnew knowledge has been obtained.(b) Contributor APIs.If contributor's modifications include an applicationprogramming interface and contributor has knowledge ofpatent licenses which are reasonably necessary to implementthat API, contributor must also include this information inthe LEGAL file.
105(c) Representations.contributor represents that, except as disclosed pursuantto section 3.4(a) above, contributor believes that contributor'smodifications are contributor's original creation(s)and/or contributor has sufficient rights to grant the rightsconveyed by this license.3.5. Required notices.You must duplicate the notice in exhibit A in each file ofthe source code.  If it is not possible to put such notice ina particular source code file due to its structure, then Youmust include such notice in a location (such as a relevantdirectory) where a user would be likely to look for such anotice.  If You created one or more modification(s), youmay add your name as a contributor to the noticedescribed in exhibit A. you must also duplicate this licensein any documentation for the source code where Youdescribe recipients' rights or ownership rights relating tocovered code.  You may choose to offer, and to charge afee for, warranty, support, indemnity or liability obligationsto one or more recipients of covered code. However, youmay do so only on your own behalf, and not on behalf ofthe Initial developer or any contributor. You must make itabsolutely clear than any such warranty, support, indemni-ty or liability obligation is offered by you alone, and Youhereby agree to indemnify the Initial developer and everycontributor for any liability incurred by the Initial develop-er or such contributor as a result of warranty, support,indemnity or liability terms you offer.3.6. Distribution of executable versions.You may distribute covered code in executable form only ifthe requirements of section 3.1-3.5 have been met forthat covered code, and if you include a notice stating thatthe source code version of the covered code is availableunder the terms of this license, including a description ofhow and where you have fulfilled the obligations of section3.2. The notice must be conspicuously included in anynotice in an executable version, related documentation orcollateral in which you describe recipients' rights relatingto the covered code. You may distribute the executableversion of covered code or ownership rights under alicense of your choice, which may contain terms differentfrom this license, provided that you are in compliance withthe terms of this license and that the license for the exe-cutable version does not attempt to limit or alter the recip-ient's rights in the source code version from the rights setforth in this license. If you distribute the executable ver-sion under a different license you must make it absolutelyclear that any terms which differ from this license areoffered by you alone, not by the Initial developer or anycontributor. You hereby agree to indemnify the initialdeveloper and every contributor for any liability incurredby the initial developer or such contributor as a result ofany such terms You offer.3.7. Larger works.You may create a larger work by combining covered codewith other code not governed by the terms of this licenseand distribute the larger work as a single product. In sucha case, you must make sure the requirements of thislicense are fulfilled for the covered code.4. Inability to comply due to statute or regulation.If it is impossible for you to comply with any of the termsof this license with respect to some or all of the coveredcode due to statute, judicial order, or regulation then youmust: (a) comply with the terms of this license to the max-imum extent possible; and (b) describe the limitations andthe code they affect. Such description must be included inthe LEGAL file described in section 3.4 and must beincluded with all distributions of the source code. Exceptto the extent prohibited by statute or regulation, suchdescription must be sufficiently detailed for a recipient ofordinary skill to be able to understand it.5. Application of this license.This license applies to code to which the initial developer hasattached the notice in exhibit A and to related covered code.6. Versions of the license.6.1. New versions.Netscape communications corporation (“Netscape”) maypublish revised and/or new versions of the license fromtime to time. Each version will be given a distinguishingversion number.6.2. Effect of new versions.Once covered code has been published under a particularversion of the license, you may always continue to use itunder the terms of that version. You may also choose touse such covered code under the terms of any subsequentversion of the license published by netscape. No oneother than netscape has the right to modify the termsapplicable to covered code created under this license.6.3. Derivative works.If You create or use a modified version of this license(which you may only do in order to apply it to code whichis not already covered code governed by this license), Youmust (a) rename Your license so that the phrases"Mozilla", "MOZILLAPL", "MOZPL", "Netscape", "MPL","NPL" or any confusingly similar phrase do not appear inyour license (except to note that your license differs fromthis license) and (b) otherwise make it clear that Yourversion of the license contains terms which differ from theMozilla Public license and netscape Public License. (Fillingin the name of the initial developer, original code or con-tributor in the notice described in exhibit A shall not ofthemselves be deemed to be modifications of this license.)
1067. DISCLAIMER OF WARRANTY.COVERED CODE IS PROVIDED UNDER THIS LICENSEON AN “AS IS” BASIS, WITHOUT WARRANTY OF ANYKIND, EITHER EXPRESSED OR IMPLIED, INCLUDING,WITHOUT LIMITATION, WARRANTIES THAT THE COV-ERED CODE IS FREE OF DEFECTS, MERCHANTABLE, FITFOR A PARTICULAR PURPOSE OR NON-INFRINGING.THE ENTIRE RISK AS TO THE QUALITY AND PERFOR-MANCE OF THE COVERED CODE IS WITH YOU.SHOULD ANY COVERED CODE PROVE DEFECTIVE INANY RESPECT, YOU (NOT THE INITIAL DEVELOPER ORANY OTHER CONTRIBUTOR) ASSUME THE COST OFANY NECESSARY SERVICING, REPAIR OR CORRECTION.THIS DISCLAIMER OF WARRANTY CONSTITUTES ANESSENTIAL PART OF THIS LICENSE. NO USE OF ANYCOVERED CODE IS AUTHORIZED HEREUNDER EXCEPTUNDER THIS DISCLAIMER.8. TERMINATION.8.1. This license and the rights granted hereunder will terminateautomatically if you fail to comply with terms herein andfail to cure such breach within 30 days of becoming awareof the breach. All sublicenses to the covered code whichare properly granted shall survive any termination of thislicense. Provisions which, by their nature, must remain ineffect beyond the termination of this license shall survive.8.2.  If you initiate litigation by asserting a patent infringementclaim (excluding declatory judgment actions) against ini-tial developer or a contributor (the initial developer orcontributor against whom you file such action is referredto as “Participant”) alleging that:(a) such participant's contributor version directly or indi-rectly infringes any patent, then any and all rightsgranted by such participant to you under sections 2.1and/or 2.2 of this license shall, upon 60 days noticefrom Participant terminate prospectively, unless if within60 days after receipt of notice you either: (i) agree inwriting to pay participant a mutually agreeable reasonableroyalty for your past and future use of modificationsmade by such participant, or (ii) withdraw your litigationclaim with respect to the contributor version againstsuch participant. If within 60 days of notice, a reasonableroyalty and payment arrangement are not mutuallyagreed upon in writing by the parties or the litigationclaim is not withdrawn, the rights granted by partici-pant to you under sections 2.1 and/or 2.2 automati-cally terminate at the expiration of the 60 day noticeperiod specified above.(b) any software, hardware, or device, other than such par-ticipant's contributor Version, directly or indirectlyinfringes any patent, then any rights granted to You bysuch participant under sections 2.1(b) and 2.2(b) arerevoked effective as of the date you first made, used,sold, distributed, or had made, modifications made bythat participant.8.3. If you assert a patent infringement claim against partici-pant alleging that such participant's contributor versiondirectly or indirectly infringes any patent where such claimis resolved (such as by license or settlement) prior to theinitiation of patent infringement litigation, then the rea-sonable value of the licenses granted by such participantunder sections 2.1 or 2.2 shall be taken into account indetermining the amount or value of any payment orlicense.8.4. In the event of termination under sections 8.1 or 8.2above, all end user license agreements (excluding distributorsand resellers) which have been validly granted by you orany distributor hereunder prior to termination shall survivetermination.9. LIMITATION OF LIABILITY.UNDER NO CIRCUMSTANCES AND UNDER NO LEGALTHEORY, WHETHER TORT (INCLUDING NEGLIGENCE),CONTRACT, OR OTHERWISE, SHALL YOU, THE INITIALDEVELOPER, ANY OTHER CONTRIBUTOR, OR ANY DIS-TRIBUTOR OF COVERED CODE,OR ANY SUPPLIER OFANY OF SUCH PARTIES, BE LIABLE TO ANY PERSON FORANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUEN-TIAL DAMAGES OF ANY CHARACTER INCLUDING, WITH-OUT LIMITATION, DAMAGES FOR LOSS OF GOODWILL,WORK STOPPAGE, COMPUTER FAILURE OR MALFUNC-TION, OR ANY AND ALL OTHER COMMERCIAL DAM-AGES OR LOSSES, EVEN IF SUCH PARTY SHALL HAVEBEEN INFORMED OF THE POSSIBILITY OF SUCH DAM-AGES. THIS LIMITATION OF LIABILITY SHALL NOT APPLYTO LIABILITY FOR DEATH OR PERSONAL INJURY RESULT-ING FROM SUCH PARTY'S NEGLIGENCE TO THE EXTENTAPPLICABLE LAW PROHIBITS SUCH LIMITATION. SOMEJURISDICTIONS DO NOT ALLOW THE EXCLUSION ORLIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAM-AGES, SO THIS EXCLUSION AND LIMITATION MAY NOTAPPLY TO YOU.10. U.S. GOVERNMENT END USERS.The covered code is a "commercial item," as that term isdefined in 48 C.F.R. 2.101 (Oct. 1995), consisting of"commercial computer software" and "commercial computersoftware documentation," as such terms are used in 48C.F.R. 12.212 (Sept. 1995). Consistent with 48 C.F.R.12.212 and 48 C.F.R. 227.7202-1 through 227.7202-4(June 1995), all U.S. Government end users acquire cov-ered code with only those rights set forth herein.
10711. MISCELLANEOUS.This license represents the complete agreement concerningsubject matter hereof. If any provision of this license isheld to be unenforceable, such provision shall be reformedonly to the extent necessary to make it enforceable. ThisLicense shall be governed by California law provisions(except to the extent applicable law, if any, provides oth-erwise), excluding its conflict-of-law provisions. Withrespect to disputes in which at least one party is a citizenof, or an entity chartered or registered to do business inthe united states of america, any litigation relating to thisLicense shall be subject to the jurisdiction of the federalcourts of the northern district of california, with venuelying in santa clara county, california, with the losing partyresponsible for costs, including without limitation, courtcosts and reasonable attorneys' fees and expenses. Theapplication of the united nations convention on contractsfor the International sale of goods is expressly excluded.Any law or regulation which provides that the language ofa contract shall be construed against the drafter shall notapply to this license.12. RESPONSIBILITY FOR CLAIMS.As between initial developer and the contributors, eachparty is responsible for claims and damages arising, directlyor indirectly, out of its utilization of rights under thislicense and you agree to work with initial developer andcontributors to distribute such responsibility on an equitablebasis. Nothing herein is intended or shall be deemed toconstitute any admission of liability.13. MULTIPLE-LICENSED CODE.Initial developer may designate portions of the coveredcode as "Multiple-Licensed". "Multiple-Licensed" meansthat the initial developer permits you to utilize portions ofthe covered code under your choice of the NPL or thealternative licenses, if any, specified by the initial developerin the file described in exhibit A.EXHIBIT A -Mozilla Public License.The contents of this file are subject to the Mozilla Public LicenseVersion 1.1 (the “license”); you may not use this file except incompliance with the License. You may obtain a copy of thelicense at http://www.mozilla.org/MPL/Software distributed under the license is distributed on an "ASIS" basis, WITHOUT WARRANTY OF ANY KIND, either expressor implied. See the license for the specific language governingrights and limitations under the License.The Original Code is ______________________________________.The Initial Developer of the Original Codeis___________________.Portions created by ______________________ are Copyright (C)_______________________. All Rights Reserved.Contributor(s): ______________________________________.Alternatively, the contents of this file may be used under theterms of the _____ license (the  "[___] License"), in which casethe provisions of [______] license are applicable instead of thoseabove.  If you wish to allow use of your version of this file onlyunder the terms of the [____] license and not to allow others touse your version of this file under the MPL, indicate your decisionby deleting  the provisions above and replace  them with thenotice and other provisions required by the [___] license.  If youdo not delete the provisions above, a recipient may use your versionof this file under either the MPL or the [___] license."NOTE: The text of this exhibit A may differ slightly from the textof the notices in the source code files of the original code. Youshould use the text of this exhibit A rather than the text found inthe original code/source code for Your modifications.
COMMERCIAL MODE SETUP GUIDENote: All features shown within this guide may not be available on all models.EXPERIENCED INSTALLERCommercial Mode Setuppage 7B-LAN Setuppage 45Cloning Informationpages 21 - 25
RECORD Model and SERIAL NUMBERThe model and serial number of this TV is located on theback of the cabinet. For future reference, we suggest thatyou record those numbers here: Model No._________________Serial No. _______________WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to thepresence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitudeto constitute a risk of electric shock to persons.The exclamation point within an equilateral triangle is intended to alert the user to the presence of importantoperating and maintenance (servicing) instructions in the literature accompanying the appliance WARNING:TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. POWER CORD POLARIZATION:This product is equipped with a 3-wire grounding-type alternating current line plug. This plug will fit into the power outletonly one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, contact your electrician toreplace your obsolete outlet. Do not defeat the safety purpose of the three-wire ground type plug.NOTE TO CABLE/TV INSTALLER:This reminder is provided to call the cable TV system installer’s attention to Article 820-40 of the National Electric Code(U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be con-nected to the grounding system of the building, as close to the point of the cable entry as practical.REGULATORY INFORMATION:This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of theFCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment isoperated in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if notinstalled and used in accordance with the instruction manual, may cause harmful interference to radio communications.However, there is no guarantee that interference will not occur in a particular installation. If this equipment does causeharmful interference to radio or television reception, which can be determined by turning the equipment off and on, the useris encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.CAUTION:Do not attempt to modify this product in any way without written authorization from LG Electronics U.S.A., Inc.Unauthorized modification could void the user’s authority to operate this product.COMPLIANCE:The responsible party for this product’s compliance is:  LG Electronics U.S.A., Inc.  1000 Sylvan Avenue, Englewood Cliffs, NJ 07632, USA • Phone: 1-201-816-2000.WARNINGRISK OF ELECTRIC SHOCK        DO NOT OPENFor Customer Support/Service, please call: 1-888-865-3026www.lgcommercial.com • www.zenith.com Marketed and Distributed in the United States by LG Electronics U.S.A., Inc.2000 Millbrook Drive, Lincolnshire, IL 60069©Copyright 2009, LG Electronics U.S.A., Inc. 206-4118PAGE 2
SAFETY INSTRUCTIONSImportant safeguards for you and your new productThis product has been manufactured and tested with safety in mind. However, improper use can result in potential electrical shockor fire hazards. To avoid defeating the safeguards that have been built into the new product, please read and observe the followingsafety points when installing and using the new product, and save them for future reference.Observing the simple precautions discussed in this installation and operating guide can help get many years of enjoyment and safeoperation that are built into the new product.This product complies with all applicable U.S. Federal safety requirements, and those of the Canadian Standards AssociationIMPORTANT SAFETY INSTRUCTIONSPAGE 3206-41181. Read InstructionsAll the safety and operating instructions should be read beforethe product is operated.2. Follow InstructionsAll operating and use instructions should be followed.3. Retain InstructionsThe safety and operating instructions should be retained forfuture reference.4. Heed WarningsAll warnings on the product and in the operating instructionsshould be adhered to.5. CleaningUnplug this product from the wall outlet before cleaning. Donot use liquid cleaners or aerosol cleaners. Use a damp clothfor cleaning.6. Water and MoistureDo not use this product near water for example, near a bathtub, wash bowl, kitchen sink, or laundry tub, in a wet base-ment, or near a swimming pool.7. Accessories, Carts, and StandsDo not place this product on a slippery or tilted surface, or onan unstable cart, stand, tripod, bracket, or table. The productmay slide or fall, causing serious injury to a child or adult, andserious damage to the product. Use only with a cart, stand, tri-pod, bracket, or table recommended by the manufacturer, orsold with the product. Any mounting of the product should fol-low the manufacturer’s instructions, and should use a mountingaccessory recommended by the manufacturer.8. Transporting ProductA product and cart combination should be moved with care.Quick stops, excessive force, and uneven surfaces may causethe product and cart combination to overturn.9. AttachmentsDo not use attachments not recommended by the product man-ufacturer as they may cause hazards.10. VentilationSlots and openings in the cabinet are provided for ventilationand to ensure reliable operation of the product and to protectit from overheating, and these openings must not be blocked orcovered. The openings should never be blocked by placing theproduct on a bed, sofa, rug, or other similar surface. This prod-uct should not be placed in a built-in installation such as abookcase or rack unless proper ventilation is provided or themanufacturer’s instructions have been adhered to.11. Power SourcesThis product should be operated only from the type of powersource indicated on the marking label. If you are not sure ofthe type of power supply to your home, consult your productdealer or local power company. For products intended to oper-ate from battery power, or other sources, refer to the operatinginstructions.12. Power Cord Polarization (Some models)This product is equipped with a three-wire grounding typealternating-current power plug. This plug will fit into the poweroutlet only one way. This is a safety feature. If you are unableto insert the plug fully into the outlet, contact your electricianto replace your obsolete outlet. Do not defeat the safety pur-pose of the three-wire ground-type plug.13. Power Cord ProtectionPower-supply cords should be routed so that they are not likelyto be walked on or pinched by items placed upon or againstthem, paying particular attention to cords at plugs, conve-nience receptacles, and the point where they exit from theproduct.PORTABLE CART WARNING
206-4118PAGE 4IMPORTANT SAFETY INSTRUCTIONS(Continued from previous page)14. Outdoor Antenna GroundingIf an outside antenna or cable system is connected to the prod-uct, be sure the antenna or cable system is grounded so as toprovide some protection against voltage surges and built-upstatic charges. Article 810 of the National Electrical Code(U.S.A.), ANSI/ NFPA 70 provides information with regard toproper grounding of the mast and supporting structure, ground-ing of the lead-in wire to an antenna discharge unit, size ofgrounding conductors, location of antenna-discharge unit, con-nection to grounding electrodes, and requirements for thegrounding electrode.15. LightningFor added protection for this product (receiver) during a light-ning storm, or when it is left unattended and unused for longperiods of time, unplug it from the wall outlet and disconnectthe antenna or cable system. This will prevent damage to theproduct due to lightning and power-line surges.16. Power LinesAn outside antenna system should not be located in the vicini-ty of overhead power lines or other electric light or power cir-cuits, or where it can fall into such power lines or circuits.When installing an outside antenna system, extreme care shouldbe taken to keep from touching such power lines or circuits ascontact with them might be fatal.17. OverloadingDo not overload wall outlets and extension cords as this canresult in a risk of fire or electric shock.18. Object and Liquid EntryNever push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock.Never spill liquid of any kind on the product.19. ServicingDo not attempt to service this product yourself as opening orremoving covers may expose you to dangerous voltage or otherhazards. Refer all servicing to qualified service personnel.20. Damage Requiring ServiceUnplug this product from the wall outlet and refer servicing toqualified service personnel under the following conditions:a. If the power-supply cord or plug is damaged.b. If liquid has been spilled, or objects have fallen into theproduct.c. If the product has been exposed to rain or water.d. If the product does not operate normally by following theoperating instructions. Adjust only those controls that arecovered by the operating instructions as an improper adjust-ment of other controls may result in damage and will oftenrequire extensive work by a qualified technician to restorethe product to its normal operation.e. If the product has been dropped or the cabinet has beendamaged.f. If the product exhibits a distinct change in performance.21. Replacement PartsWhen replacement parts are required, be sure the service tech-nician has used replacement parts specified by the manufactur-er or have the same characteristics as the original part.Unauthorized substitutions may result in fire, electric shock, orother hazards.22. Safety CheckUpon completion of any service or repairs to this product, askthe service technician to perform safety checks to determinethat the product is in proper operating condition.23. Wall or Ceiling MountingThe product should be mounted to a wall or ceiling only as rec-ommended by the manufacturer. The product may slide or fall,causing serious injury to a child or adult, and serious damageto the product.24. HeatThe product should be situated away from heat sources such asradiators, heat registers, stoves, or other products (includingamplifiers) that produce heat.Antenna Lead in WireAntenna Discharge Unit(NEC Section 810-20)Grounding Conductor(NEC Section 810-21)Ground ClampsPower Service GroundingElectrode System (NECArt 250, Part H)Ground ClampElectric ServiceEquipmentExample of Grounding According to National Electrical CodeInstructionsNEC - National Electrical Code
PAGE 5206-4118Use this page as a reference to find pages or sections to go to and set up the TV features. Go to page 7 to begin the Commercial Mode Master TV setup.Warnings  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2Important Safety Instructions  . . . . . . . . . . . . . . . . . . 3 - 4Table of Contents  . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Setup Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Commercial Mode Setup for Master TV  . . . . . . . . . . . . . 7Installer Overview  . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8FTG Card Mode of Operation Overview  . . . . . . . . . . . . . . . 9FTG Card Operation Setup  . . . . . . . . . . . . . . . . . . . . . . 10FTG Card Channel Map Overview  . . . . . . . . . . . . . . . . . . 11FTG Installer Menu Overview . . . . . . . . . . . . . . . . . . . . . 12FTG Operation Troubleshooting  . . . . . . . . . . . . . . . . . . . 13Typical Installer’s Remote Control  . . . . . . . . . . . . . . . . . 14Installer Remote Control Key Functions . . . . . . . . . . . . . . 15 Rear Connections Panel . . . . . . . . . . . . . . . . . . . . . . . . 16A/V Input 2 Side Connections Panel/RF Antenna Connection 17RJP / TV Connections & Setup  . . . . . . . . . . . . . . . . . . . 18MPI Card Slot / PPV Card Installation . . . . . . . . . . . . . . . 19TV Features Configuration Menus Overview  . . . . . . . . . . . 20TLL-1100A Cloning Instructions / Learning Setup  . 21 -22 - 23LT2002 Cloning Instructions  . . . . . . . . . . . . . . . . . 24 - 25Installer Menus  . . . . . . . . . . . . 26 - 27 - 28 - 29 - 30 - 31ReferencesDetailed Instructions For Making A Master TV  . . . . . . . . . 32Editing Channel Icons/Adding Ch Labels 2-5-4 + Menu Mode 33Clonable Menu Features / Checking Software Version . . . . . 34USB End User Features  . . . . . . . . . . . . . . . . . . . . . . . . 35USB Cloning Setup: Master TV Learning  . . . . . . . . . . . . . 36USB Cloning Setup: Master TV Teaching  . . . . . . . . . . . . . 37TV Camport Auto Sense Operation  . . . . . . . . . . . . . . . . . 38TV Aux Input Configuration / Troubleshooting  . . . . . . . . . 39Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40LT2002 Cloning Troubleshooting  . . . . . . . . . . . . . . . . . . 41Troubleshooting Flow Chart  . . . . . . . . . . . . . . . . . . . . . 42Commercial Mode Check . . . . . . . . . . . . . . . . . . . . . . . . 43Glossary of Terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44B-LAN Setup and Overview . . . . . . . . . . . . . . . . . . . . . . 45RJP Model List and Input Hierarchy . . . . . . . . . . . . . . . . 46Notes  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 Back Cover  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48Notes• See the Installer’s menus to set up the operational features of the TV. The Installer’s section content is intended to be used pri-marily by qualified TV electronics technicians. • Reference is made to installer remote controls used for menu operation within the manual. The remote information is providedfor reference only. The typical installer remote control shown for reference in this manual may be different than the actualremote control supplied with the TV. • For any additional information, contact your LG representative.Note: Design and specifications are subject to change without prior notice.Marketed and Distributed in the United States by LG Electronics U.S.A., Inc.1000 Sylvan AvenueEnglewood Cliffs, NJ 07632Table of ContentsFor Customer Support/Service please call: 1-888-865-3026www.lgcommercial.com
206-4118PAGE 6Setup ChecklistInstallation and Setup Checklist__ Unpack TV and all accessories.__ Install batteries in remote control.__ Install TV on Vesa Mount or Stand.Note: It may be advisable to make all hard-wire connections before installing on Vesamount or stand, as appropriate.Hardware Connections__ Install any additional hardware as appropriate to your institution, LAN etc.Hardwire Connections__ Make all connections to rear Jack Pack andRF antenna on MPI card.__ Make all connections to signal, interactiveresources and Aux sources as appropriate.Installer Menu Items Setup __ Configure all relevant Installer menu itemsas required of your institution. TV Menus ConfigurationConfigure TV features for the end user.__ Channel __ Picture__ Audio__ Option__ Time__ Lock__ Choose on screen menu language.(English is the default language.)Commercial Mode Setup__ Commercial Mode Setup, see next page.Software Installation__ Install or configure any software as applic-able; PPV etc.Additional Features SetupSee page 5, Table of Contents.__ Select viewing source on TV.HDMIGAMECONTROLCOMPONENT INVIDEO AUDIORLRGB IN (PC)RS-232C IN(SERVICE ONLY)UPDATERESETAUDIO INREMOTECONTROL OUTSPEAKER OUT(8   )PBYPR............................................21RJPAV IN 1VIDEO AUDIORL(MONO)HDMI/DVI INTV-LINKCFG(RGB / DVI)Except 32LH240H
PAGE 7206-4118Commercial Mode Setup for Master TV This page provides an overview of a Master TV configuration. Note 1: Disconnect all Aux inputs. Under certain conditions, Auto Tuning (Channelsearch) is disabled if there is an Aux input active.Commercial Mode Setup Procedure1. Set Installer Menu Items(Enter TV Installer Menu, see Installer menus for detailed instructions.)a. Set Installer menu item 117 FACT DEFAULT, to 001 and press ENTER onInstaller remote. (This clears all installer menu custom settings, channellabels / icons etc. and reloads the factory default settings.)b. Set Item 003 BAND/AFC.- Broadcast: set to 000.- HRC: set to 002- CATV: set to 001. -IRC: set to 003c. Set item 028 CH OVERIDE to 001. This allows access to channel search,Auto Tuning and Channel List/Edit options in the Channel Menu.d. Set other particular installer items that affect your TV programming net-work. Enable/Disable Aux sources, set a Start Channel etc.e. After all required installer menu item settings have been adjusted, pressENTER on the remote to remove Installer Menu.2. Set Up TV Features (Channel, Picture, Audio, Lock, Time, Option, Digital Captions etc. See TVClonable options list and TV menus pages.)3. Run Auto Tuning (Channel Search) (Search for all available channels.) Go to the Channel Menu and accessthe Auto Tuning option, follow onscreen instructions. a. Edit Channel Scan. In the Channel Menu, access Channel Edit option.•  Add/Delete channels per your system requirements. Note: Physical channel numbers are used to identify Virtual channels.•  Add familiar channel trademarks/logos like ABC, CBS, NBC etc. to theChannel-Time onscreen display. In the Channel menu, select the ChannelLabel option. Add identifiable labels (logos) for the end user to readilyknow what common networks are available.4. Transfer TV Setup to Internal TV Controller: 2-5-5 + Menu ModeAfter the TV channel scan has been edited and channel label iconsadded, enter the Installer menu. Once in the Installer menu, press 2-5-5and MENU on the remote. This transfers the TV setup to the internalcontroller box.5. Add Custom Channel Labels for Analog Channels: 2-5-4 + Menu ModeEnter Installer menu, press 2-5-4 and MENU. Add your own custom textlabels to  channel onscreen displays. Note: Digital Channels often have abroadcaster generated label. (See 2-5-4+Menu pages.) When finished, to exit 2-5-4+Menu mode, press MENU.Verify TV SetupAt this point, verify that the channel lineup, channel icons and customlabels are correct. Make sure the TV features are set per your requirements.Set item 028 Ch Overide to 000 to lock the channel scan. After the pre-ceding has been completed, the Master TV setup is ready to be copied to aClone Programmer, see cloning options pages.003 BAND/AFC 00X 028 CH. OVERIDE 001 117 FACT DEFAULT 00X Typical TV Installer MenuAdjust the settings for theseInstaller Menu ItemsDIGITAL 19-3WXYZMONO STEREO SAPCustom Text Label ‘WXYZ’ created in 2-5-4 + Menu (Add Channel Label) Mode028 CH. OVERIDE 000 After Master TV setup has been completed, set item 028 Ch Overide to 000.000 INSTALLER SEQ 000 UPN  000-000-000-000  FPGA E0F1PTC V1.00.000         CPU V3.06.00XXLH250H INSTALLER  MENU 093 RJP AVAILABLE 001 Set 093 RJP Available to 001 if using a remotejack pack
Installer OverviewThis is the commercial mode setup guide only. Operating Installer MenuTo set up the controls for the TV you will need to know how to enterthe TV Installer menu and make changes to the default values asrequired. If necessary, familiarize yourself with the TV Installer menuand how to make and save changes in the menu. LG Installer RemoteYou will need an LG Installer remote control similar to the oneshown to the right. The installer remote must have a “Source” but-ton or its equivalent. The remote shown in this manual has “INPUT”-- this button serves the purpose of a Source button. The TV’s clonable features need to be set up. This is a critical step.If the Master TV display panel’s clonable features like adding channelicons or channel labels are not done correctly, then the cloned TVswill all have problems. Refer to the Owner’s Manual for other TV fea-tures: Video, Audio, Closed Captions, V-Chip, etc.TLL-1100A Clone ProgrammerThe TLL is a very simple cloner to use. It can be set up to clone amaster TV setup and transfer it into a target TV. Cloning is accom-plished using the TV/Cloner MPI ports for communica-tion. Be sure the Master TV is set up completely.Cloning is only possible when the TV is tuned to anAux source or Analog channel, not a digital channel.Typical Installer MenuTV LinkLoader-DemoTLL1100AReadyTLL1100AENTERRECEIVE SENDMENUMODEMENULIST1234567809FLASHBKMUTEVOLCHPAGERETURNMARKENTERINPUTPOWERRATIOCCTIMERALAMSAPEJECT206-4118PAGE 8000 INSTALLER SEQ 000 UPN  000-000-000-000  FPGA E0F1PTC V1.00.000         CPU V3.06.00XXLH250H INSTALLER  MENU
PAGE 9206-4118FTG Card Mode of Operation OverviewOutlined below is the FTG (Free-To-Guest) setup for individual TV controlANTENNA IN M.P. I.ANTENNA/CABLE INPUTReceives RF signals.RETAINING SCREWInstall after insertingthe LMT7Z7 card.RETAINING SCREWInstall after insertingthe LMT7Z7 card.M.P.I. INTERFACEAvailable MPI port.FTG CARD  TARGET TV/STB CHANNEL MAPINSTALLER MENU CHANNEL  INSTALLER MENU MAPFTG CARD  TARGET TV/STB CHANNEL MAPINSTALLER MENU CHANNEL  INSTALLER MENU MAP1. Set up commercial features of TV/STB. Enter Installer Menu and set all desired items as required. (i.e. TuningBand, Start Channel etc.) Refer to the Installation and Setup Guide of the TV/STB.2. Load the FTG Configuration Application program onto the PC that will be used to configure the FTG card.3. Install FTG card into TV/STB’s MPI card slot and connect PC. (See below)4. Execute the FTG Configuration Application and create a configuration file.5. Build a Channel Map and ‘Write’ it to FTG card. (Converts card from pass-through to FTG mode.)6. If necessary, make changes to Installer Menu items using FTG Installer Menu Configuration utility and ‘Write’them to FTG card.7. Save the configuration file (*.rml) for future use.8. Tune TV/STB to a Logical Channel in the Channel Map.LMT7Z7 Configured Card in FTG Mode of OperationDifferent Model TV/STB FunctionCard only copies Installer Menu itemsand then installs Channel Map.Same Model TV/STB FunctionCard installs both Installer Menu itemsand Channel Map.
206-4118PAGE 10CHANNEL PICTURE AUDIO TIMEINPUT USBOPTION LOCKTypical TV/STB Setup MenuShows that the Z7 card is in pass-through mode. This menu canalso be accessed by turning IR remote access ‘On’ in the FTGConfiguration Application, while the TV/STB is in FTG mode.End User ‘Aspect Ratio’ or Function MenuShows that the Z7 card is in FTG mode. While this menu is presenton-screen, the only way the Installer menu can be accessed is bythe FTG Configuration Application.Communications Setup MenuSets up the communications link between the FTG ConfigurationApplication and the Z7 card installed in a TV/STB.Network Icon Selection MenuSelect channel icons like ABC, NBC etc., to add to the channelOSDs to identify common networks for the end user.FTG Card Mode of Operation Contd.It is easy to determine the operating mode of the TV/STB.  By pressing Menu, if the Setup or TV menu appears, the Z7 card is inpass-through mode. If the End User ‘Function’ menu appears, the TV/STB is in FTG mode.ABCMoveEnterASPECT RATIOSet By Program4:316:9ZoomJust Scan
PAGE 11206-4118DELETERemoves channel from lineup.ADDAfter inputting a new chan-nel’s data, press to add chan-nel to list.CHANNEL MAP EDITORShows both channel dataand logical channel lineup.EXIT Exits menu and returns to logicalchannel listing.LOGICAL CHANNEL NUMBERSChannels appear in numerical order.Select logical, Major and Minor num-bers on menu.CUSTOM CHANNEL LABELS/ICONSSet custom labels and select icons on menu. SET CHANNEL ATTRIBUTESSet encrypted, OSD on or off or blankvideo only.UPDATEAfter editing a channel’s data,press to include the changesin the channel list.FTG Channel Map OverviewCreating/copying a channel map into LMT7Z7 card will convert the card from pass-through mode to FTG mode. When ‘Aspect Ratio’menu is present, card is in FTG mode.
LEARNPress to transfer the installermenu settings on the TV/STBto the FTG card and PC FTGConfiguration Application.INSTALLER DEFAULTSPress to reset TV/STB to Installermenu defaults.READPress to transfer the Installer menu values on the FTG card tothe PC FTG Configuration Application.WRITEPress to transfer the FTG Installer menuvalues to the FTG card and TV/STB.EXITReturns to logical channelmap menu.IR REMOTE ACCESSToggle IR remote access to On to get access toTV/STB feature menus or Installer menu.CONFIGURATION SETTINGSSelect tabs for Installer submneuitems to set up TV/STB.HOSPITAL GRADE TV/STB ITEMSSet hospital only items on Installer menu forHospital grade TV/STBs.206-4118PAGE 12FTG Installer Menu Overview
LMT7Z7 Configured Card in FTG Mode of OperationError MessagesProblem Probable Cause SolutionCannot contact FTG application Close extra FTG application on computer. target. already open.Cable(s) not Check and connect communication cables.connected.TV off. Turn TV on.Wrong Communication port. Select correct Comm port on computer.PAGE 13206-4118FTG Operation Troubleshooting
206-4118Typical Installer Remote ControlLG Installer Remote ControlThe remote control is supplied with and dedicated to operate the TV.Some DVD and VCR controls may be available for some LG DVD/VCRproducts. See next page for typical key functions in TV mode and DVD/VCR control.Follow the instructions provided in the Installer menu pages to accessthe Installer menus.Installing Batteries in Installer Remote Control• Remove the battery compartment cover on the back side byloose the bolt on the battery compartment cover, pressing thearrow tab and sliding the cover downward.  Install batteriesmatching correct polarity as shown (+ with + and - with -).• Install two high-quality alkaline 1.5V AAA batteries. Never mixold or used batteries with new ones. Replace cover.+   AAA   AAA    + MENULIST1234567809FLASHBKMUTEVOLCHPAGERETURNMARKENTERINPUTPOWERRATIOCCTIMERALAMSAPEJECTPAGE 14
MARKUse to mark or unmark a photo/music.RATIOAdjusts the picture aspect ratio.POWERTurns TV On or Off.MUTESwitches the sound On or Off.VOLUME UP/DOWNIncreases/decreases the sound level.MENUDisplays the main menu on the screen.Enters or exits the on-screen menu systemVCR/DVD BUTTONSControl some video cassette recorders or DVDplayers. (“RECORD” is not functional in DVDmode.) Set up for VCR recording: Once, Regularly,Weekly, Off. (“RECORD” button only).TIMERSets the amount of time before the TV automatically turns itself Off.ALARMSets the time that the TV will automatically turn itself On.INPUTSelects RGB, HDMI,DVI, HDMI2, ComponentInput, AV1 and AV2 sources.CCSelects a closed caption option: Off, CC1 ~ 4, Text1 ~ 4, Service 1 ~6.NUMBER Buttons (0 - 9) DASHUse to enter a program number or channels. Dash is used for sub channel numbers such as2-1, 2-2, 9-1, 9-2, 100-3, 100-4 etc.FLASHBACKReturns to the previously tuned channel.CHANNEL UP/DOWNSelects available channels found with AutoTuning. Moves to next available page in elec-tronic program guide.THUMBSTICKUp/Down/Left/Right/ENTERUse to navigate on-screen menus / adjust the TVsettings to your requirements.RETURNClears all on-screen displays and returns to TV viewing from any TV menu.SAPSelects MTS sound: Mono, Stereo, and SAP in Analog mode.Changes the audio language in DTV mode, ifadditional languages are available.SAP Notes• If SAP is selected and no SAP is provided,sound may not be heard on channel. • Each analog channel may have its own SAPsetting. • Digital channels will reset to default audio lan-guage with a power Off/On.EJECTClears all on-screen displays and returns MENULIST1234567809FLASHBKMUTEVOLCHPAGERETURNMARKENTERINPUTPOWERRATIOCCTIMERALAMSAPEJECTRemote Control Key Functions: This typical LG TV remote control is shown for reference. Follow the instructionsprovided on the Installer menu pages to access the Installer menu.Installer Remote Control Typical Key FunctionsPAGE 15206-4118
HDMIGAMECONTROLCOMPONENT INVIDEO AUDIORLRGB IN (PC)RS-232C IN(SERVICE ONLY)UPDATERESETAUDIO INREMOTECONTROL OUTSPEAKER OUT(8   )PBYPR............................................21RJPAV IN 1VIDEO AUDIORL(MONO)HDMI/DVI INTV-LINKCFG(RGB / DVI)Rear Connections Panel206-4118PAGE 16AUDIO IN (RGB / DVI)Audio connection for eitherRGB or DVI device.COMPONENT IN Connect to output jacks oncomponent device.HDMI/DVI PORTConnect to output jacks fromHDMI / DVI device.TV-LINKUse for FTG downloads.(Except 32LH240H)SPEAKER OUT 8-OHMConnect to external speakerinput.REMOTE CONTROL OUTConnect to remote controldevice.RGB IN (PC)Connection for RGB hookupfrom PC.RS-232C INUsed for downloading soft-ware updates, etc.UPDATERestricted to softwareupdates. RESETPress RESET tore-initialize the TV.REMOTE JACK PACK PORTConnect to remote jack packcontrol output port.LANConnect to control network.(Except 32LH240H) AUDIO/VIDEO IN 1Connect to output jacks onaudio/video device.
PAGE 17206-4118A/V 2 Input: Side Connections Panel  / RF Antenna ConnectionAV IN 2  L/MONO -AUDIO- RVIDEO USB IN...........VIDEO INConnect to video output porton external device.L/MONO-AUDIO-R INConnect to audio output jacksfrom external device.For mono audio output,connect to Left audio input.USB INInsert USB device for softwareupdates and usable forPicture/Music entertainment.Antennaor CATVANTENNA IN M.P. I.RF Antenna ConnectionRF ANTENNAConnect to Antenna / Cableinput on MPI card.
•  RJP Available? If you will use a remote jack pack in your system, set installer item 093 RJP Available to 001 so the RJP function is enabled.Note: Make RJP connections first then set 093 to 001.Remote Jack Pack Setup093 RJP AVAILABLE 001 206-4118PAGE 18Remote Jack Pack (RJP) / TV Connections after Commercial Mode Setup and Cloning Master TV Setup ProceduresMake these connections after commercial mode setup and cloning procedures are completeHDMIGAMECONTROLCOMPONENT INVIDEO AUDIORLRGB IN (PC)RS-232C IN(SERVICE ONLY)UPDATERESETAUDIO INREMOTECONTROL OUTSPEAKER OUT(8   )PBYPR............................................21RJPAV IN 1VIDEO AUDIORL(MONO)HDMI/DVI INTV-LINKCFG(RGB / DVI)AUDIO IN (RGB / DVI)RGB/DVI Audio input fromRJP.HDMI/DVI PORTSConnect to output jack(s)from HDMI / DVI RJP.AUDIO/VIDEO IN 1Connect to compositeVideo/Audio output jacks onRJP.RGB IN (PC)Connection for RGB hookupfrom RJP.REMOTE JACK PACK PORTConnect to control outputport on RJP.LANConnect to control network.(Except 32LH240H)
PAGE 19206-4118MPI Card Slot / PPV Card InstallationDC INANTENNA IN M.P. I.M.P. I.Card SlotRF CABLERF cable needs to be dis-connected to remove cur-rent card.MPI Card Removal / PPV Card Installation1. Remove the two MPI card retainer screws.2. Pull out current MPI card far enough so that the RF cable can be detached from the old card.2. Detach RF cable.3. Place new PPV card into slot and slide it in far enough to reconnect RF cable.4. Insert card all the way into the slot making sure it is fully seated into back plane connector.5. Replace the two card retainer screws.The MPI card is equipped with an RF jack for antenna/cable signal source connection. The MPI card slot is also available for installing a PPV (Pay-Per-View) card.
CHANNEL PICTURE AUDIO TIMEINPUT USBOPTION LOCKTV Features Configuration Menus OverviewThe onscreen menus control the basic TV featuresMain TV MenusThe Main TV setup menus control the features of the TV. Set the TV features to thedesired configuration for the end user.Use the USB port to upgrade TV software.206-4118PAGE 20
PAGE 21206-4118Antenna(or CATV)Antenna(or CATV)TV LinkLoader-DemoTLL1100AReadyTLL1100AENTERRECEIVE SENDMENUMODECLONE SELECTION MENUSelected Bank: CBank X Saved(1) LEARN FROM TV(2) TEACH TO TV(3) SET CLONE CLOCK FROM TV(4) SET TV CLOCK FROM CLONE(5) DISPLAY TV SETUP(6) DISPLAY CLONE SETUPCLONE CLOCK = 00:00TV         CLOCK = 00:00THE CLONE IS VERSION V2.2.2-To change menu items,  Press channel keys or digits.-To execute item, Press ENTER.CLONE SELECTION MENUSelected Bank: CBank X Saved(1) LEARN FROM TV(2) TEACH TO TV(3) SET CLONE CLOCK FROM TV(4) SET TV CLOCK FROM CLONE(5) DISPLAY TV SETUP(6) DISPLAY CLONE SETUPCLONE CLOCK = 00:00TV         CLOCK = 00:00THE CLONE IS VERSION V2.2.2-To change menu items,  Press channel keys or digits.-To execute item, Press ENTER.M.P.I. Learning SetupM.P.I. Teaching SetupTV LinkLoader-DemoTLL1100AReadyTLL1100AENTERRECEIVE SENDMENUMODEConnections for the TLL-1100A Clone Programmer to Learn the TV Master TV SetupNotes: It is assumed that the TV is connected to a signalsource, the TV source selected is Antenna (RF) In, the signal isfrom an Analog channel, not a digital channel, all equipment isconnected to power and turned on and the TLL Cloner mainmenu is displayed on the TV screen, see above.TLL-1100A Cloning Connections/Learning SetupWarning: Do not use the TLL-1100A while any PPV card is installed in TV orclone programmer device will be damaged.On Master TVSet up all Master TV features onthe menus and do a ChannelSearch. Add Channel and Auxlabels etc. See previous page.Insert MPI cable into TV MPI port.On TLL-1100A1. Turn On the TLL-1100A. 2. Use the Mode button to selectClone Mode.3. Use the Left/Right arrow toselect the CBank (1 - 8) tostore the master setup in. 4. Plug the other end of the MPIcable into the MPI port on thebottom of the TLL.5. With the Installer remote con-trol, select item 1 on TLL menu. 6. Press Enter, to transfer theMaster setup into CBankX onthe TLL. The TLL will copy themaster setup. 7. When learning is done, discon-nect MPI cable from Master TV. 8. Reconnect TV power cord. Powerthe TV On and the master setupshould be resident on the TV.On Target TV1. Connect MPI cable from the TLLto the MPI port on the TargetTV. Assure that the correctCBank(X) is selected on TLL..2. With the Installer remote con-trol select item 2, to Teach thetarget TV the master TV setup.3. Press Enter to begin teaching. 4. When Teaching is done, discon-nect MPI cable and power theTV Off. Unplug TV power cord.5. Reconnect TV power cord.Power the TV On and the mas-ter setup should be resident onthe TV.GGIf an analog channel is not available, tune TV to an Aux source lik AV-1 for cloning purposes.
Before you begin cloning...• The Master TV should be connected to a good, stable signalfrom an over-the-air antenna or cable service Analog channeland connected to power. (See above.)• Teaching and Learning is only possible between identicalmodel devices. (However, the LT2002 Clone programmer canstore up to 3 different ‘master’ setups.)WARNING: Copying a blank or incorrect memory into a TV, STBor other device will cause the TV, STB or other device tooperate erratically or become inoperable.• Use an Installer’s remote to operate Learning and Teachingmenus.• Make sure that the batteries in the Clone programmer arefresh. • If batteries are removed, the Clone Clock time will be lost.• Decide if you want to set the time from the Clone program-mer or copy the time to the Clone programmer; from a com-patible TV which has the clock set to the current time.• Setting the time and transferring it to the Clone or otherdevice is a separate procedure. • Follow the connection diagram above to connect the Clone toa Master TV TV display panel. After learning is complete, toanother identical TV TV display panel to “teach” it the mastersetup.• See the Clone Troubleshooting section to resolve problems.Turn to the next page to continue Cloning Setup.QuickSet II ProgrammerLT2002®Ferrite Core(TDK, ZCAT2035-0930)ZENITH ELECTRONICS CORPORATION, LINCOLNSHIRE, ILLINOIS USA• heartbeat   power on    communications ok• slow        power on    no communications• green       battery ok• red     battery lowBlink patternColorResetStatusIndicatorConnect cable toTV MPI Jack andfollow on screeninstructionsMPITHE CLONE HAS CONTROL OF THE TVTHE CLONE IS VERSION XXTHE TV IS VERSION XXTHE SW IS REVISION XXCLONE CLOCK   = XX:XXTV CLOCK           = XX:XX-PRESS ANY KEY TO CONTINUE.-DISCONNECT CLONE WHEN DONE.Antennaor CATVMaster TVClone ProgrammerConnections for the LT2002 Clone Programmer to Learn the TV Master TV SetupNotes: It is assumed that the TV is connected to a signal source, the source selected is Antenna (RF) In, thesignal is from an Analog channel, not a digital channel, all equipment is connected to power and turned onand the LT2002 Clone Programmer main menu (THE CLONE HAS CONTROL OF THE TV) menu is displayed on theTV screen, see above and next page.LT2002 Cloning Connections/Learning SetupWarning: Do not useLT2002 while any PPVcard is installed in TV orclone programmer devicewill be damaged.206-4118PAGE 22GGIf an analog channel is not available, tune TV to an Aux source lik AV-1 for cloning purposes.
PAGE 23206-4118Use MPI Cable to Connect LT2002 Clone Programmer toMaster TV MPI PortIf there is a good connection, “THE CLONE HAS CONTROL OF TV” message will appear. Press any key on the Installer remote.Learn Setup from Master TVPress 1 to select the “LEARN FROM TV” option, then press ON/OFF,POWER, or ENTER to go to the Memory Bank Selection Menu. Pick theMemory ”Bank” you want to store the master TV’s setup in by press-ing either Channel key repeatedly to choose Memory 1, 2 or 3. (Ifyou choose a Memory “Bank” that has a master device’s setup pro-grammed into it, that setup will be overwritten by the new masterTV’s setup.) Once the Clone memory bank is selected, press ON/OFF,POWER, or ENTER. The Clone memory bank you have selected will beshown. Press ON/OFF or POWER to begin copying the master TV’ssetup.Set the Clock (Optional) Set the time on a Master TV’s Clock. (If the time has already beencopied from a TV into the Clone programmer, you can set a masterTV’s clock by copying the time from the Clone programmer.) TheClone Programmer can copy the current time to both a master TV andto the Clone’s internal clock; accurate to within one minute. (Anotherreason that the Clone programmer should be equipped with fresh,high-quality alkaline batteries, is for it to keep the time as accurate-ly as possible.)Since the Clone Programmer’s time cannot be set directly, the currenttime needs to be copied from a Zenith/LG TV equipped with M.P.I.input capability.  After the time is copied to the Clone programmer, the current timecan then be transferred to another TV. (This can be a master TV, oranother TV which has already had the features set up.)Instructions for the Clone Programmer to Learn the Master TV SetupLT2002 Clone Programmer Communication Problems• A slow flashing green light indicates there are communica-tion problems between the TV and the LT2002 clone program-mer. If this is the case, check for a damaged cable, poor con-tacts, or other connection troubles.• If the status indicator is red, the programmer batteries arelow and should be replaced.  Install 4 high-quality alkalineAA batteries. Learning the Master TV SetupTHE CLONE HAS CONTROL OF THE TVTHE CLONE IS VERSION XXTHE TV IS VERSION XXTHE SW IS REVISION XXCLONE CLOCK= XX:XXTV     CLOCK= XX:XX-PRESS ANY KEY TO CONTINUE.-DISCONNECT CLONE WHEN DONE.CLONE SELECTION MENU(1) LEARN FROM TV(2) TEACH TO TV(3) SET CLONE CLOCK FROM TV(4) SET TV CLOCK FROM CLONE(5) DISPLAY TV SETUP(6) DISPLAY CLONE SETUP-TO CHANGE MENU ITEMS,  PRESS  CHANNEL KEYS OR DIGITS.-TO EXECUTE ITEM, PRESS ON/OFF, POWER, OR ENTERThis menu should appear by itself after theLT2002 is connected to the TV MPI port.This menu should appear after any key ispressed on the Installer remote.LT2002 Cloning Learning Setup
206-4118PAGE 24Teach Master TV’s Setup to the target TVAfter learning is complete, remove the M.P.I. cable from themaster TV and connect it to the target TV that you want tocopy the master TV’s setup into. With “THE CLONE HASCONTROL OF TV” message displayed, press 2 or use eitherChannel key to go to the “TEACH TO TV” option, press ON/OFF,POWER, or ENTER. Select the LT2002 memory that the newsetup is in. Press On/Off to transfer the new setup and otherinformation to the new TV. Teaching usually takes 2-3 minutes.After the “TEACHING  COMPLETE” message is displayed, pressany key to return to the Clone menu, then press ON/OFF,POWER, or ENTER. If finished, detach M.P.I. cable from the target, newly-cloned TV.Disconnect TV Power for 15 SecondsUnplug the AC power cord of the newly-cloned TV from thepower outlet for about 15 seconds to activate the newly-copied setup. QuickSet II ProgrammerLT2002®ZENITH ELECTRONICS CORPORATION, LINCOLNSHIRE, ILLINOIS USA• heartbeat   power on    communications ok• slow        power on    no communications• green       battery ok• red     battery lowBlink patternColorResetStatusIndicatorConnect cable toTV MPI Jack andfollow on screeninstructionsMPIFerrite Core(TDK, ZCAT2035-0930)THE CLONE HAS CONTROL OF THE TVTHE CLONE IS VERSION XXTHE TV IS VERSION XXTHE SW IS REVISION XXCLONE CLOCK = XX:XXTV CLOCK         =   XX:XX-PRESS ANY KEY TO CONTINUE.-DISCONNECT CLONE WHEN DONE.Antennaor CATVTarget TV Clone ProgrammerTEACHING IN PROGRESS,PLEASE WAITTEACHING COMPLETEThis display will appear after Teachingis complete.This display will appear duringTeaching function.Teaching the Master Setup to Another TVConnections for the LT2002 to Teach another TV the Master SetupCLONE SELECTION MENU(1) LEARN FROM TV(2) TEACH TO TV(3) SET CLONE CLOCK FROM TV(4) SET TV CLOCK FROM CLONE(5) DISPLAY TV SETUP(6) DISPLAY CLONE SETUP-TO CHANGE MENU ITEMS,  PRESS  CHANNEL KEYS OR DIGITS.-TO EXECUTE ITEM, PRESS ON/OFF, POWER, OR ENTERThis menu should appear after any keyis pressed on the Installer remote.Cloning Connections/Teaching SetupGGIf an analog channel is not available, tune TV to an Aux source lik AV-1 for cloning purposes.
PAGE 25206-4118Reset Clone After Static ShockAfter replacing exhausted batteries, or if the programmerbehaves strangely after a static shock, use a paper clip or simi-lar instrument inserted through the small hole marked ”RESET”to activate the internal reset switch and restore normal opera-tion. After a reset, check the real-time clock setting. It may benecessary to reset the Clone Programmer clock from a TV con-taining the correct time.NoteThe LT2002 programmer is designed to be used with TVs con-taining the 221-01006 and later processors. Use with earlier TVsets may give unpredictable results. Processors used before the221-01006-04 have a limited screen display capability. Theycannot display entire screens as shown in the quick setupinstructions accompanying the LT2002 clone programmer. Usethe printed menu illustrations on the quick setup sheet sup-plied with the Clone as an aid to making your programming choices. (Although the menus are not all displayed, the clonefunctions all operate normally.)• After cloning operations are complete, just unplug the LT2002 from the TV.• If the TV does not display a picture on the TV (blank screen) after a few seconds, just change channels.Clone Programmer TroubleshootingProblem Possible Cause(s) Possible Solution(s)Clone ProgrammerClone copies Setup in • Not enough time to copy - Press Reset on clone programmer, redo teach/learn.less than 30 seconds entire TV setup. (Teach/Learn should take a minimum of 1 minute.)Remote does not • Wrong Installer remote. - Only use an LG Installer remote to operate clone programmeroperate clone. with TV.LED does not blink. • M.P.I. cord not connected. - Connect M.P.I. cord properly, assure good connection.• TV not turned on. - TV must be powered On for clone to work.• Weak batteries. - Install 4 fresh AA high-quality alkaline batteries.Clone menu hard  • Weak signal. - Connect TV to a reliable Analog channel signalto read. source.No time set. • Time not available. - Set time on a TV, copy time to Clone Programmer.Clone not working. • Clone programmer  - Try a different LT2002 Clone programmer.problem. - Reset Clone Programmer.Clone Scans Channels • Clone should only scan  - Retry cloning again.more than once. channels once.Master and Other TVsCloning did not work. • Procedure interrupted. - Wait until procedure complete message is displayed.• Different TV models. - Cloning is only possible with identical model TVs.• Step(s) omitted or - Reread pages 7-8-9 to be sure all tasks were performed.not performed.Clone time disappeared. • Batteries were removed. - Batteries must remain installed to retain time settings.New Setup not present. • TV not reset. - Disconnect newly-cloned unit from power for 5 seconds.Reference: LT2002 Cloning Procedure TroubleshootingWarning: Do not use LT2002 while any PPV card isinstalled in TV or clone programmer will be damaged.
Use the Installer’s Menu to set up or change operational settings.See more detailed descriptions of the Installer menu items on the following pages...Accessing the Installer’s MenuMake sure TV is on. Installer’s menu items can be accessed by using an installer’s remotecontrol. Just press MENU repeatedly until the TV seems to stop responding, then press 9,8, 7, 6, then ENTER to access the Installer’s menu. To remove the Installer’s menu, pressENTER again. Any changes you make will be stored in nonvolatile memory.The Installer’s menu opens with item 000 INSTALLER SEQ 000. Use the Up/Down arrowkeys to sequence through the available menu items. Or, access an item directly by keyingin the line number, then pressing MENU. For example, to access the Sleep Timer optionwhich is item 015, press 0-1-5, then MENU. To change a setting, use the Left/Rightarrow keys. Or, enter a value directly.Using the Installer’s MenuItems 000 ~ 118 are immediately accessible only upon entering the Installer’s Menu.Their numbers, descriptions, ranges, factory default settings, and a place for listing anychanges made on-site are given below and on the following pages. Installer menu itemsnot relevant to this TV series are not present on the Installer menu, therefore some num-bers are missing.  Items 006, 012, 013 etc., will not appear.Installer Menu Items 000 through 034Menu Item Function Value Range Default Value Brief Description of Function and Comments000 INSTALLER SEQ 0 ~ 3 0 Leave default set to 0.001 POWER MANAGE 0 ~ 7 0 Sets number of hours of no activity before auto shut Off.002 AC ON 0 / 1 0 Set to 1 to enable auto turn On at power up.003 BAND/AFC 0 ~ 3 1 Selects Tuning Band: 0=Broadcast, 1=CATV, 2=HRC, 3=IRC004 STRT CHANNEL 0 ~ 127, 255 255 Channel at turn-on (Set to 255 to tune in last channel before power Off).005 CHAN LOCK 0 / 1 0 If set to 1, cannot tune from current channel.007 STRT VOLUME 0 ~ 63, 255 255 Sets Volume level at TV turn-on (Set 255 to retain last volume level).008 MIN VOLUME 0 ~ 63 0 Sets minimum allowable volume setting.009 MAX VOLUME 0 ~ 63 63 Sets maximum allowable volume setting.010 MUTE DISABLE 0 / 1 0 Set to 1 to disable mute function.011 KEY DEFEAT 0 / 1 0 Set to 1 to disable menu navigation keys on display panel.015 SLEEP TIMER 0 / 1 1 Set to 1 to enable Sleep Timer.016 EN TIMER 0 / 1 0 Set to 1 to enable On/Off Timers.017 ALARM 0 / 1 1 Set to 1 to enable Alarm.021 V-CHIP 0 / 1 1 Set to 1 to enable V-Chip functions.022 MAX BLK HRS 0 ~ 99 12 Sets number of V-Chip (Parental Control) blocking hours.023 CAPTION LOCK 0 / 1 0 Set to 1 to retain caption setting at power Off.028 CH. OVERIDE 0 / 1 1 If set to 0, limits direct access to favorite channels.029 OLD OCV 0 / 1 0 Set to 1 to change M.P.I. operation to OCV.030 ACK MASK 0 / 1 0 If set to 1, changes M.P.I. for some OCV boxes.031 POLL RATE 20 ~ 169 94 Selects poll rate for M.P.I.032 TIMING PULSE 186 ~ 227 207 Sets baud rate for M.P.I.034 CAMPORT EN 0 / 1 1 Set to 1 to enable Video 2 input.Installer Menu206-4118PAGE 26000 INSTALLER SEQ 000 UPN  000-000-000-000  FPGA E0F1PTC V1.00.000         CPU V3.06.00XXLH250H INSTALLER  MENU Typical Installer Menu
Menu Item Function Value Range Default Value Brief Description of Function and Comments035 COMPPORT EN. 0 / 1 1 Set to 0 to disable HDMI 1. Set to 1 enable HDMI 1038 YPrPb EN. 0 / 1 1 Set to 1 to enable display panel Component Video 1 input jacks.039 REAR AUX EN 0 / 1 1 Set to 1 to enable display panel Video 1 input jack.040 AUTO CAMPORT 0 / 1 1 Set to 1 to automatically switch to Camport. If set to 1, STRT AUX SRCE cannot be set to 2.046 STRT AUX SRCE 1 ~ 6, 255 6 Sets the starting AUX source.047 AUX STATUS 0 / 1 0 Set to 1 for M.P.I. AUX source to be reported as a channel number instead of Channel 0.053 DIS. CH-TIME 0 / 1 0 Set to 1 to disable Channel-Time display.069 EN. CH-T COL. 0 / 1 1 Set to 1 to enable custom color for the Channel-Time display.070 FOR. CH-TIME 0 ~ 7 2 Chooses custom foreground color for the Channel-Time display.071 BCK. CH-TIME 0 ~ 7 2 Chooses custom background color for the Channel-Time display.073 CH NOT AVBLE 0 / 1 0 If set to 1 and channel override is 0, “NOT AVAILABLE” message is displayedwhen directly accessing a channel not in the favorite channel list.075 REVERT CH 0 / 1 0 If set to 1 and loss of M.P.I. communication occurs, TV tunes to Start Channel.078 UPN MSB 0 ~ 255 0 User programmable number, most significant byte.079 UPN MSB-1 0 ~ 255 0 User programmable number, most significant byte - 1.080 UPN MSB-2 0 ~ 255 0 User programmable number, most significant byte - 2.081 UPN LSB 0 ~ 255 0 User programmable number, least significant byte.082 CHKSM ERROR 0 / 1 1 Enforces rigid M.P.I. checksum.083 HANDSHK TIME 0 ~ 5 5 Relaxes M.P.I. timing to be compatible with PC based Windows-controlled systems.084 PERMANENT BLK 0 / 1 0 Removes block hours setting for Parental Control and makes block permanent.087 REAR RGB EN. 0 / 2 / 18 2  Set to 0 to disable RGB1. Set to 2 to enable for PC and Auto Configure always enabled. Set to 18 to enable for PC and Auto Configure one time only after AC ON.088 EN NOISE MUTE 0 / 1 1 If set to 1, mutes audio if no signal is present.090 KEY LOCK 0 / 1 0 If set to 1, keyboard is locked out, IR is still functional.091 YPrPB2 EN 0 / 1 1 Set to 1 to enable HDMI-2 input.093 RJP AVAILABLE 0 1 2 5 6 0 Set to 0 to disable. Set to 1, 2, 5 or 6 for HDMI or DVI mode. (See detailed descriptions.)094 SAP MENU EN 0 / 1 1 Set to 0 to disable feature on Function menu. Set to 1 to enable feature on Function menu.096 DEF. ASP. RATIO 0 ~ 4 2 Sets default aspect ratio at power up. See detailed descriptions and item 106.098 START GEM CH 0 ~ 135, 255 255 Sets the stating Gem channel, 255=last channel at power Off.099 BACK LIGHTING 1 ~ 100 200 Sets the brilliance of the TV picture backlighting.101 ~ 200, 255 Settings above 101 control dynamic back lighting and disable power saving mode..102 ATSC BAND 0 ~ 4 4 Selects ATSC band.103 ATSC TUNE MODE 0 / 1 1 Default 01 for physical channel scan. Set to 0 for Virtual Channel scan.104 START MINOR CH 0 ~ 255 0 Selects Minor start channel. Set 0 for NTSC.  Not 0, sets Minor channel number.106 ASP RATIO LOCK 0 / 1 0 To retain set aspect ratio on power cycle, set to 1. Set to 0 for default ratio on power cycle.116 VIDEO MUTE EN 0 / 1 0 Set to 0 for normal, set to 1 for Blank.117 FACT DEFAULT 0 / 1 0 0=Normal. 1=Loads presets of all above settings.118 POWER SAVING 1, 3, 7 3 Set to 1 to be powered at b-Lan module. Set to 3 to bo powered at b-Lan module only when TV is powered on. Set to 7 to be not powered at b-Lan module.Installer Menu Items 035 through 118Installer MenuPAGE 27206-4118Note 1: Dependent on item 093 RJP Available setting. (Except 32LH240H)
PAGE 28Detailed Descriptions of Installer Menu Items 000 - INSTALLER SEQUENCE Specifies entry sequence to the Installer Menu. 0 = 9876  1 = 4321 2 = 1478  3 = 3698001 - POWER MANAGE (Power Management)Determines hours of no activity before automatic shutoff. The POWERMANAGE function is for saving energy. If set to 0, Power Manage is Off.Settings range from 0 ~ 7, with 1 ~ 7 representing the hours that theunit will remain On, unless there has been activity from either thecontrol panel or remote control.002 - AC ON (AC Power Switchable)If set to 1, allows the TV to turn On just by applying AC power.Pressing the On button is not necessary. This is desirable if the TV isplugged into a cable box or a power outlet controlled by a wall switch.Use ADJ Left/Right arrow to choose 0 or 1 where 0 is the default isOff, and 1 is On.NOTE: If set to 1 (On), the TV does not respond to On/Off commandsfrom either the remote or the display control panel, and the SLEEPTIMER is also nonfunctional.003 - BAND/AFC (Band/Automatic Frequency Control)There are 4 possible settings for this option:0 = Broadcast  1 = CATV 2 = HRC  3 = IRC If some channels were not found by Auto Tuning (Channel Search),select the appropriate Band setting here and add the channels usingthe Channel Edit option in the Channel Menu.004 - STRT CHANNEL (Start Channel)If active, this function allows you to determine the initial channelnumber when the TV is turned On. This feature is useful for an in-house information channel, since the TV would always select thatchannel when it is turned On.  Setting this to 255 causes the lastchannel viewed when the TV was turned Off, to be the tuned to chan-nel when the TV is turned On again.  Note: For a digital Start Channel,always remember to set item 104 to the Minor Start Channel number.255 = Last channel 1 ~ 125 = Ch X       0 = Aux 126 Map to Channel 3.  127 Map to Channel 4.005 - CHAN LOCK (Channel Lock)CHAN LOCK is ideal if the system must always be on the same channel.Changing channels with Channel Up/Down or keypad numbers is impos-sible. Channel Lock is inactive if set to 0 (default).Generally, this feature is used in connection with START CHANNEL(Installer item 004) where the start channel may, for example, be setto 3 or 4. If the start channel is 3, then the TV will remain locked onChannel 3.NOTE: For Items 007, 008 and 009For legacy reasons, the scale used is 0 - 63. The PTC software willtranslate this to the 0 - 100 scale used by the TV.To translate a TV volume level to the installer menu value, use the fol-lowing formula:Installer Value = TV Value x 63100Enter only the whole number (disregard fractions).007 - STRT VOLUME (Start Volume)This function allows the Installer to determine the initial volume levelsetting when the TV is turned On. This feature is useful for an in-houseinformation channel, since the TV would always select that volumelevel when it is turned On. The range of values are 0 - 63, 255. If 255is selected, the current volume level will be retained in memory whenthe TV is turned Off; at turn On, the volume level will be automaticallyset at the previous or last level.008 - MIN VOLUME (Minimum Volume)This function determines the minimum volume level allowable with theVOLUME (VOL) Up/Down control. In this way, for example, someonecannot set the volume too low to hear. The value range is from 0 to 63— change values with ADJ Left/Right arrow. The factory default is 0,which provides the full range of volume control, if item 009 MAX VOL-UME is also set to 63. It may be best to set the same value on everyTV. NOTE: The minimum volume level cannot have a value setting higherthan the MAX VOLUME level (described below).009 - MAX VOLUME (Maximum Volume)This function determines the maximum volume level allowable with theVOLUME (VOL) Up/Down controls. In this way, for example, someonecan not set the volume level high enough to disturb others. The valuerange is 0 to 63, with 63 as the default, which gives the user the fullrange of volume control, if item 008 MIN VOLUME is also set at 0.Change values with ADJ Left/Right arrow keys. It may be best to setthe same value on every TV. NOTE: The maximum volume level cannot have a value setting lowerthan the MIN VOLUME level (described previously).010 - MUTE DISABLEEnables or disables sound mute function. If set to 1, sound cannot bemuted. If set to 0, sound can be muted. 206-4118Installer Menu
PAGE 29206-4118011 - KEY DEFEAT (Keyboard Defeat)If set to 1, key defeat prevents the end user from accessing the on-screen menus with the display front panel—MENU, SELECT, and Left /Right arrow keys do not function. If set to 0, those keys do function.NOTE: The menus can always be accessed by pressing MENU on theremote.015 - SLEEP TIMERIf set to 1, the SLEEP TIMER feature may be used. If set to 0, theSleep Timer is not available. 016 - EN TIMER (Enable On/Off Timers) *If set to 1, Timer function is available to user and enabled continuous-ly.  Set to 0 to disable On/Off Timers. (Clock must be set in order touse Timers.) 017 - ALARM *Gives the installer the option of making the Alarm function availableto the end user. If set to 1, Alarm function is available to end user.Set to 0 to disable the Alarm function. NOTE: Clock must be set before the Alarm function will work.021 - V-CHIP (Parental Control) *Set to 1 to activate V-Chip (Parental Control); have it available to enduser to filter and control or otherwise restrict programming contentthat can appear. Set to 0 to turn V-Chip feature Off, not available touser; no programming restrictions can be set. 022 - MAX BLK HRS (Maximum Block Hours) *Sets hours from 0 to 99 for the maximum V-Chip (Parental Control)block hours. Default setting is for 12 blocking hours.023 - CAPTION LOCKSet to 1 to restore previous caption On/Off state after turn Off. If setto 0, captions are always Off at turn On.028 - CH. OVERIDE (Channel Override)If set to 1, the user can select channels with either Channel up/downor by direct keypad entry. If set to 0, only those channels that areentered for scanning can be selected.029 - OLD OCV (On Command VideoTM)Set to 1 for operation with systems from On Command Corporation.030 - ACK MASKM.P.I. Communication Parameter. Leave at default setting unlesschanged by Pay-Per-View provider. When set to 1, changes M.P.I. forsome OCV boxes.* Only affects Function Menu if enabled by some PPV providers.031 - POLL RATEM.P.I. Communication Parameter. Selects Poll Rate for M.P.I. Leave atdefault setting unless changed by Pay-Per-View provider. Step size of16 ms.032 - TIMING PULSEM.P.I. Communication Parameter. Leave at default setting unlesschanged by Pay-Per-View provider. Sets baud rate. Step size of 4.3 uS.034 - CAMPORT EN. (Camera Port Enable)Set to 1 to enable Video 2 input on display panel. If set to 0, Video 2input on display panel is not functional. NOTE: S-Video overrides Video jack.035 - COMPPORT EN. (Computer Port Enable)Enable/disables display panel HDMI1 input jack. Set to 0 to disableHDMI 1. set to 1 to enable HDMI 1.NOTE: The setting above is ignored if Installer item 093 RJP AVAIL-ABLE, is set to 1. 038 - YPrPb EN. (Rear Component Video Enable)Set to 1 to enable display panel rear Component Video input jacks. Set to 0 to disable display panel rear Component Video input jacks.039 - REAR AUX EN. (Rear Aux Enable)Set to 1 to enable display panel rear AUX (Video 1) input. Set to 0 to disable display panel rear AUX (Video 1) input. Note: S-Video overrides Video.040 - AUTO CAMPORTSet to 1 to automatically switch to Camport when equipment is con-nected to front Video input.Set to 0 to disable front Video automatic source selection.NOTE: If set to 1, 093 RJP Available is automatically set to 0.046 - STRT AUX SRCE (Start Aux Source)Sets the starting AUX source. At power up, TV will tune to starting Auxsource if item 004 Start Channel is set to 0.If item 093 RJP Available is set to 0 and item 040 Auto Camport is set to 0:1 = Video 1 4 = RGB 255 = Last Aux2 = Video 2 5 = HDMI 23 = HDMI 1 6 = ComponentIf item 093 RJP Available is set at 1:2 = Video 2 5 = HDMI 2 6 = ComponentIf item 040 Auto Camport is set to 1:1 = Video 1 5 = HDMI 23 = HDMI 1 6 = Component4 = RGBInstaller Menu
PAGE 30 206-4118Installer Menu047 - AUX STATUSSet to 1 for M.P.I. AUX source to be reported as a channel numberinstead of channel 0.  Set to 0 to disable AUX identification change.Controls M.P.I. status channel response for AUX inputs.053 - DIS. CH-TIME (Disable Channel-Time)Set to 1 to disable the Channel-Time display, Channel-Time display willnot appear.Set to 0 to enable the Channel-Time display.069 - EN. CH-T COL. (Enable Channel-Time Custom Color)Set to 1 to enable custom color for the Channel-Time display.Set to 0 to disable custom color for the Channel-Time display.070 - FOR. CH-TIME (Channel-Time Display Foreground Color)Set according to Color Chart.0 = Black 3 = Yellow 6 = Cyan1 = Red 4 = Blue 7 = White2 = Green 5 = VioletNOTE: If foreground and background color are the same, menu back-ground is transparent.071 - BCK. CH-TIME (Channel-Time Display Background Color)Set according to Color Chart.0 = Black 3 = Yellow 6 = Cyan1 = Red 4 = Blue 7 = White2 = Green 5 = VioletNOTE: If foreground and background color are the same, menu back-ground is transparent.073 - CH NOT AVBLE (Channel Not Available)If set to 1 and item 028 CHANNEL OVERRIDE is set to 0, “NOT AVAIL-ABLE” message is displayed when directly accessing a channel not inthe channel scan list available in memory.075 - REVERT CH (Revert to Start Channel)If set to 1 and loss of M.P.I. communication occurs, TV automaticallytunes to the specified Start Channel.078 - UPN MSB (UPN Most Significant Byte)User programmable number, most significant byte readable by M.P.I.command.  Note: Not linked to serial number.079 - UPN MSB-1 (UPN Most Significant Byte-1)User programmable number, most significant byte-1 readable by M.P.I.command. Not linked to serial number.080 - UPN MSB-2 (UPN Most Significant Byte-2)User programmable number, most significant byte-2 readable by M.P.I.command. Not linked to serial number.081 - UPN LSB (UPN Least Significant Byte)User programmable number, least significant byte readable by M.P.I.command. Not linked to serial number.082 - CHKSM ERROR (Checksum Error)Enforces rigid M.P.I. checksum validation.Set to 1 for validation. Set to 0 to disable (does not check checksum on M.P.I. async port).SPI is always checked.083 - HANDSHK TIME (Handshake Time)Adds an additional delay to the handshake time which is 64 msec,thus relaxing M.P.I. timing requirements to be compatible with PCbased Windows controlled systems, range is 0 - 5. (Timeout = 25.5MS + [25.5 MS* Handshake time]).084 - PERMANENT BLK (Permanent Block)Allows Lock (Parental Control) blocking schemes to be permanent bydisabling the blocking hours function. Set to 1 to install Parental Control restrictions permanently. Set to 0 for user-specified hours control of blocking schemes.087 - REAR RGB EN. (Rear RGB Enable)Controls access to rear RGB input on TV. Set to 0 to disable RGB input. Set to 2 to enable for PC and Auto Configure always enabled.Set to 18 for Auto Configure one time only with power cord removaland reinsertion.088 - EN NOISE MUTE (Enable Noise Mute)If set to 1, audio mutes if no signal is present.090 - KEY LOCK If set to 1, display panel keyboard is locked out, not available to enduser.  IR receiver remains functional.091 - YPrPb2 EN. (HDMI2 Enable)Set to 0 to disable display panel HDMI2 input.Set to 1 to enable DTV mode. Set to 2 to enable PC mode.Detailed Descriptions of Installer Menu Items
206-4118 PAGE 31093 -RJP AVAILABLE (Remote Jack Pack Available)0 = Remote jack pack is not available or disabled.1 = Legacy Model RJPs: HDMI ModeEnables RJP when an HDMI cable is inserted into RJP. Video is fromHDMI. Audio stream is expected from HDMI source. If no audio is pre-sent, no audio will be heard.2 = Legacy Model RJPs: DVI Mode Enables RJP when an HDMI cable is inserted into RJP. Video is fromHDMI however, Audio is from selected audio source, based on the RJP’saudio hierarchical priority.5 = Scaler Model RJPs: HDMI ModeEnables RJP when an HDMI cable is inserted into RJP. Video is fromHDMI. Audio stream is expected from HDMI source. If no audio is pre-sent, no audio will be heard.6 = Scaler Model RJPs: DVI ModeEnables RJP when an HDMI cable is inserted into RJP.Video is from HDMI however, Audio is from selected audio source,based on the RJP ’s audio hierarchical priority.Notes:See Reference section, RJP Input Hierarchy and RJP Models page.If set to 1, 2, 5 or 6, item 040 Auto Camport is automatically set to 0.Settings 1, 2, 5 and 6 allow the lodge staff to customize each TV ’sRJP setup based on customer requirements.094 - SAP MENU EN (2nd Audio Program) Set to 1 to enable SAP feature on Function menu, if Function menu isavailable. Set to 0 to disable SAP feature on Function menu, if Function menu isavailable.096 - DEF. ASP. RATIO (Default Aspect Ratio)Selects default aspect ratio at power up, see settings below.Set to 0 for “Set By System”. Set to 1 for 4:3.Set to 2 for 16:9 (Factory Default). Set to 3 for ‘Just Scan’Set to 4 for Zoom 099 - BACK LIGHTING Sets the TV screen brightness at power up, see settings below. Default setting is 200. 1 - 100 Static Backlighting. (1 = Dimmest picture, 100 = Brightest picture.) 101 - 200 Dynamic Backlighting. (101 = Dimmest picture, 200 = Brightest picture.) If settings are above101, the TV automatically controls backlighting depending upon thepicture level of the current program.set to 255, to disable power saving mode. 102 - ATSC BAND Sets up TV to receive different types of incoming signals: 0=Broadcast, 1=CATV, 2=HRC, 3=IRC, 4=Same as NTSC.103 - ATSC TUNE MODE Sets ATSC tuning mode: Default set to 1 for Physical channel scan. Set to 0 for Virtual Channel scan.104 - START MINOR CHANNEL Sets XX-XX minor start channel number at power up: 0=NTSC. If not 0,number selected is the Minor start channel number.106 - ASP RATIO LOCK (Aspect Ratio Lock)Set to 1 to retain previous aspect ratio with power Off. Set to 0 to retain default aspect ratio with power Off. See item 96Default Aspect Ratio above.116 - VIDEO MUTE EN (Video Mute Enable)Set to 0 for normal. Set to 1 for blank.117 - FACT DEFAULT (Factory Default)Set to 0 for normal. Set to 1 to load presets to all of the previous item set-tings.WARNING: Setting this to 1 will reload the factory defaultsand clear the channel list including erasing any assignedChannel Icons and custom channel Labels.118 - Power Saving (Except 32LH240H) Default is set to 3. When TV is in Standby mode, MPI card slot ispowered by Standby power supply and embedded BLAN is not pow-ered. When TV is in Power On mode, MPI card slot is powered bymain 12V power supply and embedded BLAN is powered. Note, TVmust be powered on in order to communicate with the embeddedBLAN module for configuration and control.1 = MPI card slot Standby mode power provided from Standbypower supply and embedded BLAN is always powered on.3 = MPI card slot Standby mode power provided from Standbypower supply and embedded BLAN only powered on when TV ispowered on.7 = MPI card slot Standby mode power provided from Standbypower supply and embedded BLAN always powered off.Installer Menu
PAGE 32 206-4118IMPORTANT INSTALLER SETUP INFORMATION!  PLEASE READ THE FOLLOWING...To set up a master TV you will need to know how toenter the TV Installer menu and make changes tothe default values as required. If necessary, famil-iarize yourself with the TV Installer menu and howto make and save changes in the menu, before attempting toclone the TV Master TV setup. You will also need an LG Installer remote control similar tothe one shown in the front of this manual. The installer remotemust have a “Source” button or its equivalent. The remoteshown in this manual has a “INPUT” button -- this buttonserves the purpose of a Source button. Finally, the TV’s clonable features need to be set up. This is acritical step. If the Master TV display panel’s clonable featureslike adding channel icons or channel labels, digital font optionsetc., are not correctly added, then the cloned TVs will all haveproblems. As the cloning procedure is being performed, specific stepsneed to be done at the indicated times to achieve the desiredresult. Be sure to do each task as indicated. If a procedure orstep is left out or not performed completely, cloning may notwork. At each step, pay attention to assure the TV screen showsthe proper message when cloning. If the message indicateddoes not appear, there is a problem with that step and cloningmay not be successful. Cloning is only possible when the signalsource is an Analog channel, not a digital channel.Reference: Detailed Instructions For Making A Master TVMaking a Master TVDetailed InstructionsThe following describes the procedure for preparing a Master TVfor cloning and the procedure for adding Channel Icons and/orLabels.Note 1: Disconnect all Aux inputs. Under certain conditions,Auto Tuning Channel Search is disabled if there is an Aux inputactive.Note 2: Under certain conditions, changes to the input mode ofthe RGB inputs will not take effect until the power is cycled (TVis turned Off and On). To avoid confusion, disconnect all RGBinputs before entering the Installer menu.1. Enter the TV installer menu.  a. Reset the internal controller to factory default by access-ing installer menu item 117 FACT DEFAULT, set it to 1 andpress “ENTER”. The value will change back to 0 after the TV’sinternal controller has been restored to factory default con-dition. This step will ensure that the TV channel memory willbe the active channel list. Check the Status LED. If it isblinking rapidly then the TV channel map is in use. b. Within the Installer menu, set the Installer menu items tothe configuration required of your institution.  c. It is important to set the tuning band at this time, seeInstaller menu item 03 BAND/AFC.  d. Set Installer menu item 28 – CH OVERIDE to 001 to allowaccess to the Auto Tuning and Ch. Edit features in theChannel Menu.  Exit the Installer menu.2. Access the Master TV menus and set the clonable options onthe menus to the desired configuration.  Refer to theClonable Menu Features Chart in this manual.3. Run Auto Tuning to find analog and digital channels.4. Enter the Channel Edit menu and edit the channel lineup toinclude the Free-To-Guest Channels only. 5. Assign ICONs to the channels using the Channel Label Menu.Note: You can add Channel ICONS typically network logoslike ABC, NBC, PBS etc. in this step. Or, in Step 7, addChannel ICONS or labels for channels without Icons.6. Transfer the TV setup:  Enter the TV installer menu.  Press ‘2’,‘5’, ‘5’, ‘MENU’ to start the transfer of the TV’s setup to theinternal controller.  Once the transfer is complete, the sys-tem will exit the Installer menu. Check the Status LED insidethe TV. It should be blinking slowly (1 blink per second).7. Edit/Add Channel ICONs and Channel Labels as needed.  Enter Installer menu. With menu displayed, press 2-5-4 +MENU. See next page for detailed instructions:- Editing/Adding Channel ICON and Labels on Master TV- Changing a Channel’s ICON on Master TV - Changing/Adding Channel Labels on Master TV- Changing Source Labels on Master TV8. Verify Master TV setup and feature configuration:• Did you add Channel ICONS?• Did you add Channel Labels?• Did you add Source Labels?• Did you adjust all TV menu options as required? After verifying master setup, enter the TV Installer menu andset Installer menu item 28 CH OVERIDE to 000. Press ENTERto remove and exit the Installer menu.
206-4118 PAGE 33Changing a Channel’s ICON onMaster TV1. With Channel Up/Down, select the channel you want to change the Icon for. 2. With the Right or Left ADJ arrow, select the thin letter ‘I’ on the channel ID display.3. With the Up or Down arrow, select the desired ICON you want to appear to identify the channel. (If you know the ICON number, enter the number followed by Enter / Select.)4. Proceed with Changing/Adding Labels or go to the next channel.Changing/Adding Channel Labelson Master TV1. Channel Up/Down to select the desiredchannel. 2. Press the Right or Left ADJ arrowrepeatedly until the numbers 1 to 7show up.  The number shows the posi-tion of the character that can bechanged. Number 1 is the first charac-ter, number 2 the second characterand so on.3. With the Up or Down arrow, select thedesired character.4. Proceed to the next number positionor use Channel Up/Down to go to thenext channel.Changing Source Labels onMaster TV1. Press “INPUT” to select the desiredAux input source; A/V 1, A/V 2, HDMIComponent, RGB etc.2. Press the Right or Left arrow repeated-ly until the numbers 0 to 9 shows up.The number shows the position of thecharacter that can be changed.3. Use the Up or Down arrows to selectthe desired character.4. Press “INPUT” for the next Aux sourceor proceed with Changing Icon orChanging/Adding Labels. Press ChUp/Down to return to channels.• CHANNEL Up/Down - Tunes in the next channel in scan.• Left/Right Arrows - Select the item to change.  If “I” isshown, the ICON can be changed.  If a number is shown, itindicates the position of the character that can be changed.• Up/Down Arrows - Select the ICON or the character to bedisplayed. Tip: Arrows can be held down for fast scrolling.• 0 – 9 - Use to enter the index number of the ICON, if known.• ENTER/SELECT -  Changes the ICON after the number hasbeen entered.• INPUT -  Changes the Aux input label. (“Source” on theremote shown in this manual is INPUT.)• MENU - Exits the editing process.  Installer Remote Control Key Functions for Master TV Channel Editing/Labeling MenuAdding Channel Icons and Labels in the 2-5-4 + Menu ModeReference: Procedures for adding Channel Label Icons/Custom Channel Labels(2-5-4 + MENU Mode) Editing/Adding Channel ICONs and/or LabelsIf there is no pre-assigned ICON, you can make a custom chan-nel label of up to 7 characters to help in identifying the chan-nel or network.  At your option, channel labels can also beadded in addition to a pre-assigned ICON.  You may also addlabels for the Aux input sources to clearly identify the devicesthat are connected to the Aux inputs.Editing and adding the labels can only be done if there arechannels entered into the TV’s channel map either by using themethod described in item 6 (page 18), by cloning or by the useof the master remote control from the PPV provider. Note: A blank letter space is available between ‘Z’ and ‘!’.To Do Channel Editing/Labeling, Proceed as Follows1. Enter TV Installer menu.2. Once the installer menu appears, press ‘2’, ‘5’, ‘4’,‘MENU’. This enters the channel label editing mode.Add your channel icons and channel labels in thismenu, see below. (You can do this more than once.)3. To exit the menu when done press “MENU”.1234567XYZXYZXYZNETWORK(Icon)(Label)
Procedure for Checking Software VersionThe software version of the TV may be checked by accessing the Installer Menu.  To do this, press MENU repeatedly until the menu display ceases to respond to MENU key presses.  Then, press "9", "8", "7", "6", "ENTER".  Press ENTER again to remove Installer Menu from screen.Typical Installer Menu000 INSTALLER SEQ 000 UPN  000-000-000-000  FPGA E0F1PTC V1.00.000         CPU V3.06.00XXLH250H INSTALLER  MENU PAGE 34 206-4118Reference: Clonable Menu FeaturesNotes • Picture Menu and other menu settings shown above are not clonable on all TVs. End user has access to Picture, Sound and Ratio on user remote control.• Menu options vary between Analog / Digital channels and Aux Sources.Menu /Sub Menu Features Installer Menu Installer Item settingsChannelAuto Tuning (Channel Lineup)Channel Edit Channel labelPictureAspect Ratio Picture Mode Advanced ControlAudioAuto Volume  Clear Voice  Sound Mode  BalanceClonable Menu FeaturesAudio Contd.Treble Bass  SRS TruSoundXT  TV Speaker   OptionLanguageCaption  Caption Mode   DTV Captions Style - Style  DTV Captions Style - Size  DTV Captions Style - Font   DTV Captions Style - Text Color  DTV Captions Style - Text Opacity  DTV Captions Style - BG Color  DTV Captions Style - BG Opacity DTV Captions Style - Edge Type  DTV Captions Style - Edge Color  LockMovie Rating  TV Rating – Children Age  TV Rating – Children Fantasy Violence  TV Rating – General Age  Input BlockTimeAuto ClockManual ClockOff TimeOn TimeAuto Off  CPU VersionPTC Version
PAGE 35206-4118USB End User FeaturesSlideshowToggles slideshow On and Off.DeleteRemoves slide from slideshow.RotateRotates picture.Back Ground MusicToggles selected musicfile On and Off.USBUSB Menu features Picture Slideshow with or without Music accompanimentUSB Device SetupOn the USB device, load Photo and Music files e.g. MP3. Insert USB device into USB port onTV side jack panel. Press Menu and select USB option, press Enter. Note: Windows .wma files are not usable.View PicturesSelect USB Icon and press Enter. Select Photo List option and press Enter. Select Folderphotos are in. Press Enter. When photo list appears, choose Photo and press Enter.View Picture with MusicSelect USB Icon and press Enter. Select Music Folder option. Select Music List and selectPlay with Photo. Select music MP3 file and press Enter.Listen to Music MP3 FilesSelect USB Icon and press Enter. Select Music List option and press Enter. Select Folder withMusic MP3 files. Press Enter. Adjust Volume to comfortable listening level.Slideshow BGM OptionDelete HideSlideshow 1 / 79 9OptionPress to access availableoptions. Selects slideshowplayback speed.HideRemoves menu from screen.Press Enter to display again.Slide Being ShownIndicates present slide beingshown and number of slidesavailable.Sound LevelIndicates volume setting.
PAGE 36 206-4118Reference USB Cloning: Master TV Profile Setup-LearningOn Master TV, Create Profile and Learn1. Set up all Master TV features on the menus and doa Channel Search.Add Channel and Aux Labels etc.Do 255+menu on Installer Menu to save current TVinto flash memory.2. Plug USB memory card into the USB In port onMaster TV.3. Press Menu key to open Main menu. Highlight theOption icon.4. Press the Left arrow key once, the Option icon onleft side of menu will be highlighted.5. Press number key ‘7 ’a total of 7 times.6. Access the “Learn From TV “ option.a. First, Expert Download Menu page will not showthe “Learn From TV ”. In order to make “LearnFrom TV available, key in the password which isused to enter Installer Menu. Example 9-8-7-6. b. By pressing up/down arrow keys (if there is othermenus), place the cursor on Learn From TV, thenpress Enter Key.7. Using Up/Down arrow key,highlight “Learn FromTV ”, then press Enter.8. To identify the profile from others, you canchange the last 5 digits. Key in a custom filename, then press the Enter key.9. The Learning status will be shown on progress bar.As soon as learning the current profile is com-plete, a message will appear on screen indicatingthe learning process is done.10. Remove the USB memory card.Notes• Do not remove TV power cord or USB memory card whileLearning, doing so might harm your USB memory card.• Do not remove TV power cord or USB memory card whileTeaching,doing so may cause the T V t malfunction.• You are allowed to edit the file name, however, a file withedited contents will not be recognized.• Since clock data is copied into USB memory card as numericdata,the time difference between teaching and learning isnot automatically adjusted. Either set the clock manually, oruse Auto Clock set on TV main menu.Optional: Edit / Change File NameIf necessary, the file name can be edited or changed.USB Download MenuUpgrade TV SoftwareUpgrade PTC SoftwareTeach To TVLearn From TVLearn From TVXX250H-UA00001.TLLSelect the file name and press OK to start.EEPreviousEnterLearn From TVUPGRADING...48 %Do not unplug!
PAGE 37206-4118Reference USB Cloning: Master TV Profile Setup-Teaching1. Plug USB memory card with Master TV Profilesetup into Target TV USB input port.2. Press Menu key to open Main menu and then highlight the Option Menu icon.3. Press the Left arrow key once, this will highlightthe Option icon on left side of menu.4. Press number key ‘7 ’, a total of 7 times.5. Using the Up/Down arrow key, select ‘Teach to TV’,then press Enter key.6. Use Up/Down arrow keys to navigate through profiles. Select the profile that you want to installby highlighting it and pressing the Enter key.7. Teaching progress will be shown on the progressbar. As soon as teaching is done, a message willappear indicating that the teaching process hasbeen completed.8. When Teaching is done, remove the USB memorycard and unplug TV power cord.9. Reconnect TV power cord. Power the TV On andthe master setup should be resident on the TV.On Target TV, Teach Master TV ProfileTeach To TVXX250H-UA00001.TLLPreviousEnterTeach To TVUPGRADING...39 %Do not unplug!
PAGE 38 206-4118TV Camport Auto Sense OperationThe CAMPORT Auto Sense function is enabled when:1. Installer Menu Item 34, CAMPORT EN is set to 1 AND2. Installer Menu Item 40, AUTO CAMPORT is enabled (1).Selectable= Can be accessed with INPUT key, direct access, etc.Auto Sense= Switches to this input when connector is inserted.The camport (Side Video) has the highest priority and will over-ride any commands including tuning to the Start Channel.CAMPORT (Front Video) Functionality ControlItem 34  Item 40 Front VideoCAMPORT EN  AUTO CAMPORT Operation0 0 Disabled0 1 Disabled1 0 Selectable1 1 Auto SenseCAMPORT Operation (Stand-Alone)When Camport Auto Sense is enabled as above, the TV’s sourcewill switch to the side video aux source whenever a plug isinserted into any of the side video panel inputs (either com-posite Video or S-Video).When the plug is removed, the TV will switch back to the previ-ous channel or input source that the TV was using before theplug was inserted. However, if any direct access to an RF chan-nel or Aux channel is requested while the camport is active,then, when the camport plug is removed, the TV will switch tothe last requested channel. Source changes using any SourceKeys (INPUT) are ignored. Channel Up/Channel Down andFlashback Commands are not direct access tuning commandsand they are also ignored.Previous State Operation StateBefore Inserting While CAMPORT Upon RemovalCAMPORT Is Active Of CAMPORTAux or RF Channel  None  Previous Auxor RF ChannelAux or RF Channel Direct Access Last RequestedRF or Aux ChannelAux or RF Channel Ch Up/Down, Previous AuxFlashback  or RF Channeland TV/AV KeysCAMPORT Operation (PPV)The operation will be similar to that of the Stand-Alone mode.However, the PPV providers may send different commands tothe TV for the same user commands. For instance, someproviders will always send a direct tune command when itreceives a channel up/down or a flashback command whileother PPV providers will just send a key command.Previous State Operation StateBefore Inserting While CAMPORT Upon Removal CAMPORT Is Active Of CAMPORTAux or RF Channel None Previous Auxor RF ChannelAux or RF Channel Direct Access Last Requested RFor Aux ChannelAux or RF Channel Ch Up/Down, Last RequestedFlashback Channel if PPVand TV/AV Keys translates it todirect access tuningcommand. Otherwise,goes to Previous Auxor RF Channel
206-4118 PAGE 39OLD_OCV=0OLD_OCV=1Source Input Source Mode Number Labeling Value Labeling Value Labeling130 90 Video2 (Side) CV/SVIDEO 34 CAMPORT_EN 0x01 Video Front (Camport) 0Video Front (Camport) 0 (VIDE0) 2131 91 Video1 (Rear) CV/SVIDEO 39 REAR_AUX_EN 0x02 Rear Video (Aux) 1Rear Video (Aux) 0 (VIDE0) 1DTV 91 YPrPb2 EN = 1 0x04 S-Video Rear 2S-Video Rear 0 (VIDE0) 5PC 91 YPrPb2 EN = 2 0x04 S-Video Rear 2S-Video Rear2 (COMPUTER) 5DTV 35 COMPPORT EN = 1 0x08 Front Computer 3Front Computer 0 (VIDE0) 3PC 35 COMPPORT EN = 2 0x08 Front Computer 3Front Computer2 (COMPUTER) 3PC 87 REAR RGB EN = 2 0x10 SVGA Rear Computer 4SVGA Rear Computer2 (COMPUTER) 4136 96 Component 38 YPrPb EN 0x40 Y/UV Component 6Rear Y/PrPb Component video0 (VIDE0) 6Installer MenuTVDIRECT ACCESS Tuning START AUX SOURCE ASSIGNMENTDATA STATUS TYPE 0X0D AUX SOURCE (R)ENABLE MPI DATADATA STATUS TYPE 0xD2 CURRENT AV SOURCE (R)MPI DATA STATUS TYPE  0x41 SOURCES ENABLED (R/W)132 92 HDMI2134 94 RGB133 93 HDMI1/DVI137 97 USB 121 USB Options  0x80 Y/C FrontVideo6FrontS-Video 2 (Comp) NATV Aux Input Configuration / TroubleshootingTroubleshootingSome quick and easy tips to resolving problemsSymptoms Possible Cause(s) Possible Solution(s)Software ProblemsCannot direct enter Channel not included in channel  After 2-5-5 + MENU, only channels included in TV controller will appear.channel number or  scan in TV controller. If channel is available it can be added to channel scan. If it is not “No Signal” appears. available, the ‘No Signal’ message appears on the TV screen.
PAGE 40 206-4118Some quick and easy tips to resolving problemsSymptoms Possible Cause(s) Possible Solution(s)PowerNo Power. See troubleshooting flow chart.Display Panel PictureNo Picture. • Display panel is turned off. -Turn TV on. -Power failure?• Antenna/Cable not connected. -Connect Antenna/Cable signal to TV. (See Owners manual)• Connections incorrect. -Check connections on TV. (See Owners manual)• M.P.I. not connected. -If applicable, connect M.P.I. cable to M.P.I. device.• Encrypted program. -Try another channel.• Wrong tuning band. -Adjust Installer menu settings.Erratic OperationInstaller menu setup. • Wrong Installer menu settings. -Adjust Installer menu settings as required.Remote ControlRemote doesn’t work. • Remote not in TV mode. -Use Mode key to select TV; puts remote into TV mode.• Not aimed at IR remote sensor. -Point remote at TV’s IR receiver on TV.• Remote too far from IR sensor. -Move remote closer to TV’s IR receiver or darken room.• IR path to TV’s receiver obstructed. -Remove obstructions.• Weak batteries. -Replace batteries.• Wrong battery polarity. -Check that “+” and “-” match in battery compartment.• Too much light in room. -Dim room light.• Wrong Installer remote control. -Requires compatible Installer remote, contact your LG dealer.Picture ReceptionNormal picture, poor • Audio muted.  -Press MUTE or use Volume Up key to increase sound level.or no sound. • Broadcast problem. -Try a different channel.Note: For other problems not caused by the TV, refer to other devices’ operating guide.Troubleshooting
PAGE 41206-4118Reset Clone After Static ShockAfter replacing exhausted batteries, or if the programmerbehaves strangely after a static shock, use a paper clip or simi-lar instrument inserted through the small hole marked ”RESET”to activate the internal reset switch and restore normal opera-tion. After a reset, check the real-time clock setting. It may benecessary to reset the Clone Programmer clock from a TV con-taining the correct time.NoteThe LT2002 programmer is designed to be used with TVs con-taining the 221-01006 and later processors. Use with earlier TVsets may give unpredictable results. Processors used before the221-01006-04 have a limited screen display capability. Theycannot display entire screens as shown in the quick setupinstructions accompanying the LT2002 clone programmer. Usethe printed menu illustrations on the quick setup sheet sup-plied with the Clone as an aid to making your programming choices. (Although the menus are not all displayed, the clonefunctions all operate normally.)• After cloning operations are complete, just unplug the LT2002 from the TV.• If the TV does not display a picture on the TV (blank screen) after a few seconds, just change channels.Clone Programmer TroubleshootingProblem Possible Cause(s) Possible Solution(s)Clone ProgrammerClone copies Setup in • Not enough time to copy - Press Reset on clone programmer, redo teach/learn.less than 30 seconds entire TV setup. (Teach/Learn should take a minimum of 1 minute.)Remote does not • Wrong Installer remote. - Only use an LG Installer remote to operate clone programmeroperate clone. with TV.LED does not blink. • M.P.I. cord not connected. - Connect M.P.I. cord properly, assure good connection.• TV not turned on. - TV must be powered On for clone to work.• Weak batteries. - Install 4 fresh AA high-quality alkaline batteries.Clone menu hard  • Weak signal. - Connect TV to a reliable Analog channel signalto read. source.No time set. • Time not available. - Set time on a TV, copy time to Clone Programmer.Clone not working. • Clone programmer  - Try a different LT2002 Clone programmer.problem. - Reset Clone Programmer.Clone Scans Channels • Clone should only scan  - Retry cloning again.more than once. channels once.Master and Other TVsCloning did not work. • Procedure interrupted. - Wait until procedure complete message is displayed.• Different TV models. - Cloning is only possible with identical model TVs.• Step(s) omitted or - Reread pages 7-8-9 to be sure all tasks were performed.not performed.Clone time disappeared. • Batteries were removed. - Batteries must remain installed to retain time settings.New Setup not present. • TV not reset. - Disconnect newly-cloned unit from power for 5 seconds.Reference: LT2002 Cloning Procedure TroubleshootingWarning: Do not use LT2002 while any PPV card isinstalled in TV or clone programmer will be damaged.
PAGE 42 206-4118ControllerQuickCheckIs'STATUS'LED onAnalog BoardBlinking?Pluginto AC Power OutletIsTVConnected toAC Power?BadTVYesNo NoYesIsRed LEDon TVLit?1. Bad Analog Board.2. Bad Digital Board.NoCycle the power by removingand re-connecting the ACpower cord.  Observe the'POWER' LED and TV screenas soon as AC power is re-applied.BadTVDidAnalogBoard 'POWER'LED Turn OnMomentarily?NoCheck to see if TVis in Commercial Mode.See Commercial ModeCheck chart.Did TVTurn OnMomentarily?NoYesYesYesDidTV TurnOn?YesNoPress 'POWER' or 'ON/OFF'key on TV1. Bad TVPress 'POWER' or 'ON/OFF'or 'VOLUME UP/DOWN' or'MUTE' key on InstallerRemoteDidTVRespond?No 1. Bad TV2. Go to Remote    Control Checklist page 5YesPress 'POWER' or 'ON/OFF'or 'VOLUME UP/DOWN'or 'MUTE' key onUser-Supplied RemoteDidTVRespond?No 1.  Bad PPV Card2.  Go to Remote     Control Checklist page 5YesEndTroubleshooting Flow Chart
PAGE 43206-4118Commercial Mode CheckPress the "On/Off" key on the front panel.The On/Off key is always operational.Didyou geta response?Bad TVYesNoDidTV stoprespondingor continue to respond?TV is inCommercialMode.StoppedrespondingTV is not in Commercial ModeCall Technical Support forAssistanceContinuedtorespondLeavetheTV set OnGo to Installer menuby pressing "MENU" untilthe TV stops responding.
206-411875 OHM RF CABLE The wire that comes from an off-air antennaor cable service provider. The end looks likea hex-shaped nut with a wire stickingthrough the middle. It screws onto theAntenna/Cable threaded jack on the back ofthe TV.300 TO 75 OHM ADAPTER A small device that connects a two-wire 300 ohm antenna to a 75 ohm RF jack.They are usually about an inch long with twoscrews on one end and a round opening witha wire sticking out on the other end. A/V CABLESAudio/Video cables. Three cables bunchedtogether—right audio (red), left audio(white), and video (yellow). A/V cables areused for stereo playback of videocassettesand for higher quality picture and soundfrom other A/V devices.A/V DEVICEAny device that produces video or sound(VCR, DVD, cable box, or television).AMPLIFIERAn electronic device that amplifies soundfrom a television, CD player, VCR, DVD, orother Audio/Video device.ANTENNAThe physical receiver of television signalssent over the air. A large metal piece ofequipment does not always have to be visibleto be using an antenna.B-LANTV is controlled by external network.CABLE Cable service box. Refers to the descramblerbox cable subscribers use to receive cableprogramming signals.CATVProgramming provided by a cable service.DIGITAL TELEVISIONHigh-resolution, cinema-quality televisionsignals transmitted digitally.DVI Digital Video InterfaceAccommodates analog and digital interfaceswith a single connector.COMPOSITE VIDEOTypical video jack, uses one wire for trans-porting three-color video signals.COMPONENT VIDEOUses three wires for transporting three-colorvideo signals. The end result is usually bettervideo quality.DELETEDLets you remove channels from the list thatthe end user can scroll through using CH(Channel) Up/Down.HDMI High-definition multi-media interface.HDTV High-definition television. Refers to televi-sion signals that have higher resolution thanordinary analog TV signals.HDSTB High-definition set top box. Refers to atuner device that receives high-definitiontelevision signals which have higher resolu-tion than ordinary analog TV signals.INPUT Refers to the input jack that receives a sig-nal from a TV, VCR, DVD Player or otherAudio/Video device.JACKAn input or output connector on the backof a TV, VCR, DVD Player or otherAudio/Video device.MONO SOUNDMono (monaural) sound is one channel ofsound. On more than one speaker, all thespeakers play the same audio. OUTPUTRefers to the output jack that sends a signalout of a VCR, DVD, or other A/V device.PHYSICAL CHANNEL NUMBERThe actual channel number. Analog channelsuse the physical channel number and digitalchannels can use a virtual channel number.RGB (Red, Green, Blue)Connection input or output port available forproducing a video image using three sepa-rate colors: Red, Green, and Blue. RS-232Serial communication port through whichfirmware is downloaded.2ND AUDIO PROGRAMMING/SAPSecond Audio Programming (SAP) is another,separate audio channel available with someprogramming.  Choosing SAP often refers tolistening to audio in another language, suchas Spanish or French.SIGNALPicture and sound traveling through a cable,or over the air, to the TV.STEREO SOUNDStereo (Stereophonic) sound refers to audiothat’s divided into right and left sides. TUNERDevice that picks up the broadcast signaland turns it into picture and sound. VIRTUAL CHANNEL NUMBERA re-mapped channel number analog chan-nels use the actual channel number. but dig-ital channels use a virtual(or false) channelnumber.XDSExtended Data Service: Additional programinformation included on the signal providedat the discretion of the broadcaster.Note 1Refer to www.atsc.org for further informa-tion.Glossary of TermsA list of definitions for some of the words found in this guidePAGE 44
PAGE 45206-4118B-LAN OverviewB-LAN Setup and Overview (Except 32LH240H) Power to the B-LAN module is controlled by Installer Menu Item 118 Power savings. By default, value 003, the B-LAN module isonly powered on when the TV is powered on. There are two bits in the Power Savings item to control power to the B-LAN module,one for power during TV Standby mode and one for power during TV Power On mode. When the bit is 0, the B-LAN module is pow-ered. When the bit is 1, the B-LAN module is not powered (Power Savings is Enabled).The B-LAN module is internal to the TV. It allows the Hotel/Institution headend equipment to communicate with the TV for config-uration and control. This communication is via the institution’r RF distribution system. The control device at the headend (ex FMA-LG101) can control multiple TVs. When the TV is first installed, it must be powered on in order for the headend to be able to com-municate with the B-LAN. At this point, if it is desired for the BLAN to always be powered on, particularly during Standby mode,the BLAN Standby Power Saving mode setting should be downloaded as Disabled. The new settings will not be active until theBLAN actually downloads the configuration data to the PTC and the PTC is reset.If it known that the application requires only using the MPI card slot and not the embedded BLAN, the installer can go into theInstaller Settings menu and enable the BLAN Power Savings mode, in both Standby and TV power on.Power Saving137TV Power On StateStandbyStandbyStandbyTV Standby StateOnOffOffBLAN Power MPI Slot Power BLAN Power MPI Slot PowerOnOnOffMainMainMain
Reference: RJP Model List and Input HierarchyRJP Model ListLegacy Models Scaler ModelsRJP-101M Not Support PCBRJP-101ML Not Support PCBRJP-110F RJP-210FRJP-110FW RJP-210FWRJP-110W RJP-210WRJP-110WBR RJP-210WBRRJP-110S RJP-210SRJP-120G RJP-220GRJP-120T RJP-220TRJP-201B RJP-301BRJP-202B RJP-302BRJP Input HierarchyPriority Video Audio1st. (Highest) HDMI / DVI 3.5mm Mini Jack2nd. RGB L / R Audio In3rd. Composite HDMI / DVI4th. (Lowest) TV (RF or Aux) TV (RF or Aux)206-4118PAGE 46
Regulatory Information cont. FCC Compliance StatementThis equipment has been tested and found to complywithin the limits of a Class B digital device pursuant to Part15 of the FCC Rules. These limits are designed to providereasonable protection against harmful interference in aresidential installation.This equipment generates, uses, and can radiate radiofrequency energy and if not installed and used inaccordance with the instructions, may cause harmfulinterference to radio communications. However, there isno guarantee that interference will not occur in a particularinstallation.If this equipment does cause harmful interference to radioor television reception (which can be determined byturning the equipment on and off), the user is encouragedto try to correct the interference by using one or more ofthe following measures:Reorient or relocate the receiving antenna.Increase the separation between the equipment and the receiver.Connect the equipment into an outlet on a circuitdifferent from that to which the receiver is connected.Consult the dealer or an experienced radio/TVtechnician for help.Caution: Changes or modifications not expressly approvedby the party responsible for compliance could void theuser's (or your) authority to operate the equipment. Onlyperipherals (digital input/output devices, terminals, printers,etc.) certified to comply with the Class B limits may beattached to this monitor. Operation with non-certifiedperipherals is likely to result in interference to radio and TV reception. Only shielded signal cables may be used withthis System.Canadian DOC NoticeThis Class B digital apparatus meets all requirements ofthe Canadian Interference-Causing Equipment Regulations. Cet appareil numérique de la classe Brespecte toutes les exigences du Règlement sur lematériel brouilleur du Canada.CE Conformity Notice (for Europe)Products with the “CE” Marking comply with the EMCDirective(89/336/EEC) and LOW VOLTAGE Directive(73/23/EEC) issued by the Commission of the EuropeanCommunity.Compiance with these directives implies conformity to thefollowing European Norms :•  EN 55022 ; Radio Frequency Interference•  EN 55024 ; Electromagnetic Immunity•  EN 61000-3-2 ; Power Line Harmonics•  EN 61000-3-3 ; Voltage Fluctuations•  EN 60950-1 ; Product SafetyLow Radiation Compliance (MPR II)This monitor meets one of the strictest guidelines availabletoday for low radiation emissions, offering the user extrashielding and an antistatic screen coating. Theseguidelines, set forth by a government agency in Sweden,limit the amount of emission allowed in the Extremely LowFrequency (ELF) and Very Low Frequency (VLF)electromagnetic range.01NOTICEThe regulations are applied only to the products with theID LABEL indicating specific requirements.NOTICEThe regulations are applied only to the products with theID LABEL indicating specific requirements.NOTICEThe regulations are applied only to the products with theID LABEL indicating specific requirements.TCO'99 (TCO'99 applied model only)Congratulations!You have just purchased a TCO’99 approved and labelledproduct! Your choice has provided you with a productdeveloped for professional use. Your purchase has alsocontributed to reducing the burden on the environment andalso to the further development of environmentallyadapted electronics products.
Regulatory Information cont. 02Why do we have environmentally labelled computers?In many countries, environmental labelling has become anestablished method for encouraging the adaptation ofgoods and services to the environment. With the growingmanufacture and usage of electronic equipmentthroughout the world, there is a recognized concern for thematerials and substances used by electronic productswith regards to their eventual recycling and disposal. Byproper selection of these materials and substances, theimpact on the environment can be minimized.There are also other characteristics of a computer, such asenergy consumption levels, that are important from theviewpoints of both the work (internal) and natural (external)environments. Electronic equipment in offices is often leftrunning continuously, resulting in unnecessaryconsumption of large amounts of energy and additionalpower generation. From the standpoint of carbon dioxideemissions alone, it is vital to save energy.What does labelling involve?The product meets the requirements for the TCO’99scheme which provides for international and environmentallabelling of personal computers and/or displays. The labelling scheme was developed as a joint effort by the TCO (The Swedish Confederation of ProfessionalEmployees), Svenska Naturskyddsforeningen (The Swedish Society for Nature Conservation) andStatens Energimyndighet (The Swedish NationalEnergy Administration).Approval requirements cover a wide range of issues:ecology, ergonomics, emission of electrical and magneticalfields, energy consumption and electrical safety. Ecological criteria impose restrictions on the presence anduse of heavy metals, brominated and chlorinated flameretardants, and other substances. The product must beprepared for recycling and the manufacturing site(s) shallbe certified according to ISO14001 or EMAS registered.Energy requirements include a demand that the systemunit and/or display, after a certain period of inactivity,shall reduce its power consumption to a lower level in oneor more stages. The length of time to reactivate the systemunit shall be reasonable for the user.Labelled products must meet strict environmentaldemands, for example, in respect of the reduction ofelectrical and magnetical fields as well as work load andvisual ergonomics.Below you will find a brief summary of the ecologicalrequirements met by this product. The completeecological criteria document can be found at TCODevelopment’s website http://www.tcodevelopment.comor may be ordered from:TCO DevelopmentSE-114 94 STOCKHOLM, SwedenFax: +46 8 782 92 07Email : development@tco.seInformation regarding TCO’99 approved and labelledproducts may also be obtained athttp://www.tcodevelopment.comEcological requirementsFlame retardantsFlame retardants may be present in printed wiring boardlaminates, cables, and housings. Their purpose is toprevent, or at least to delay the spread of fire. Up to 30%by weight of the plastic in a computer casing can consist offlame retardant substances. Many flame retardantscontain bromine or chlorine, and these flame retardantsare chemically related to PCBs (polychlorinatedbiphenyls). Both the flame retardants containing bromineor chlorine and the PCBs are suspected of giving rise tohealth effects, including reproductive damage in fish-eating birds and mammals, due to the bio-accumulative*processes when not disposed of in accordance with strictstandards for disposal.TCO’99 requires that plastic components weighing morethan 25 grams shall not contain flame retardants withorganically bound bromine or chlorine. Flame retardantsare allowed in the printed wiring board laminates due tothe lack of commercially available alternatives.Cadmium**Cadmium is present in rechargeable batteries and in thecolour-generating layers of certain computer displays.TCO’99 requires that batteries, the colour-generatinglayers of display screens, and the electrical or electronicscomponents shall not contain any cadmium.Mercury**Mercury is sometimes found in batteries, relays andswitches. TCO’99 requires that batteries shall not containany mercury. It also demands that mercury is not presentin any of the electrical or electronics componentsassociated with the labelled unit. There is however one
Regulatory Information cont. 03exception. Mercury is, for the time being, permitted in theback light system of flat panel monitors as there today isno commercially available alternative. TCO aims onremoving this exception when a mercury free alternative isavailable.Lead**Lead can be found in picture tubes, display screens,solders and capacitors. TCO’99 permits the use of leaddue to the lack of commercially available alternatives, butin future requirements TCO Development aims atrestricting the use of lead._____________________________________________* Bio-accumulative is defined as substances which accumulate in living organisms.**Lead, Cadmium and Mercury are heavy metals which are bio-accumulative.TCO’03(TCO’03 applied model only)Congratulations!The display you have just purchased carries the TCO’03Displays label. This means that your display is designed,manufacturedand tested according to some of the strictest quality andenvironmental requirements in the world. This makes for ahigh performance product, designed with the user in focusthat also minimizes the impact on our natural environment.Some of the features of the TCO’03 Display requirements:Ergonomics•     Good visual ergonomics and image quality in order toimprove the working environment for the user and toreduce sight and strain problems. Importantparameters are luminance, contrast, resolution,reflectance, colour rendition and image stability.Energy•     Energy-saving mode after a certain time – beneficialboth for the user and the environment•     Electrical safetyEmissions•     Electromagnetic fields•     Noise emissionsEcology•     The product must be prepared for recycling and themanufacturer must have a certified environmentalmanagement system such as EMAS or ISO 14 001•     Restrictions onchlorinated and brominated flame retardants andpolymersheavy metals such as cadmium, mercury and lead.The requirements included in this label have beendeveloped by TCO Development in co-operation withscientists, experts, users as well as manufacturers all overthe world. Since the end of the 1980s TCO has beeninvolved in influencing the development of IT equipment ina more user-friendly direction. Our labelling system startedwith displays in 1992 and is now requested by users andIT-manufacturers all over the world.For more information, please visitwww.tcodevelopment.comInformation for Environmental PreservationLGE. announced the 'LG Declaration for a CleanerEnvironment' in 1994, and this ideal has served as aguiding managerial principle ever since. The Declaration isa foundation that has allowed us to undertakeenvironmentally friendly activities in careful considerationof economic, environmental, and social aspects.We promote activities for environmental preservation, andwe specifically develop our products to embrace theconcept of environment-friendly. We minimize the hazardous materials contained in ourproducts. For example, there is no cadmium to be found inour monitors.Information for recyclingThis monitor may contain parts which could be hazardousto the environment. It is important that this monitor berecycled after use.LGE. handles all waste monitors through anenvironmentally acceptable recycling method. There areseveral take-back and recycling systems currently inEnglish
Regulatory Information cont. 04operation worldwide. Many parts will be reused andrecycled, while harmful substances and heavy metals aretreated by an environmentally friendly method.If you want to find out more information about ourrecycling program, please contact your local LG vendor ora corporate representative of LG. We set our vision and policies on a cleaner world byselecting the issue of the global environment as a task forcorporate improvement. Please visit our website for moreinformation about our ‘green’ policies.http://www.lge.com/about/environment/html/Recycling.jspInformationen zur Erhaltung der UmweltIm Jahr 1994 verkündete LGE die 'LG Declaration for aCleaner Environment' (LG Erklärung für eine sauberereUmwelt). Seitdem dient dieses Ideal als führendes Prinzipdes Unternehmens. Diese Erklärung war die Basis für dieDurchführung von umweltfreundlichen Aktivitäten, wobei wirtschaftliche,umweltbezogene und soziale Aspekte in die Überlegungen mit einbezogen wurden.Wir fördern Aktivitäten zum Schutz der Umwelt und dieEntwicklung unserer Produkte ist darauf ausgerichtet,unserem Konzept bezüglich Umweltfreundlichkeit gerechtzu werden. Wir sind darauf bedacht, den Anteil der in unserenProdukten enthaltenen schädlichen Materialien zuminimieren. So ist in unseren Monitoren beispielsweisekein Kadmium zu finden.Informationen zum Thema RecyclingDieser Monitor enthält Teile, die umweltschädlich seinkönnen. Es ist unbedingt erforderlich, dass der Monitorrecycelt wird, nachdem er außer Dienst gestellt wurde.Bei LGE. werden alle ausrangierten Monitore in einemunter umweltbezogenen Aspekten geeigneten Verfahrenrecycelt. Augenblicklich sind weltweit mehrereRücknahme- und Recyclingsysteme im Einsatz. VieleTeile werden wieder verwendet und recycelt. SchädlicheSubstanzen und Schwermetalle werden durchumweltverträgliche Verfahren behandelt.Falls Sie mehr über unser Recyclingprogramm erfahrenmöchten, wenden Sie sich bitte an Ihren lokalen LG-Händler oder einen Unternehmensvertreter von LG. Wir richten unsere Firmenpolitik auf eine sauberereUmwelt hin aus, indem wir umweltspezifische Aspekte alswichtigen Punkt in die Weiterentwicklung unseresUnternehmens einfließen lassen. ZusätzlicheInformationen über unsere ‘grüne’ Firmenpolitik erhaltenSie auf unserer Website.http://www.lge.com/about/environment/html/Recycling.jspInformation sur la protection del’environnementLGE. a publié sa 'Déclaration en faveur d’unenvironnement plus propre' en 1994 et celle-ci est restée,depuis lors, un principe directeur de notre entreprise.Cette déclaration a servi de base à notre réflexion et nousa permis de prendre en compte à la fois les aspectséconomiques et sociaux de nos activités, tout enrespectant l’environnement.Nous encourageons les activités en faveur de lapréservation de l’environnement et c’est dans cet esprit que nous développons nos produits : nous réduisons auminimum les matières dangereuses qui entrent dans leurcomposition et l’on ne trouve pas de cadmium, parexemple, dans nos moniteurs.Information sur le recyclageCe moniteur peut contenir des composants qui présententun risque pour l’environnement. Il est donc important quecelui-ci soit recyclé après usage.LGE. traite les moniteurs en fin de cycle conformément àune méthode de recyclage respectueuse del’environnement. Nous reprenons nos produits et lesrecyclons dans plusieurs sites répartis dans le mondeentier. De nombreux composants sont réutilisés etrecyclés, et les matières dangereuses, ainsi que lesmétaux lourds, sont traités selon un procédé écologique.Si vous souhaitez plus de renseignements sur notreprogramme de recyclage, veuillez contacter votrerevendeur LG ou un l’un de nos représentants. Nous voulons agir pour un monde plus propre et croyonsau rôle de notre entreprise dans l’amélioration del’environnement. Pour plus de renseignements sur notrepolitique “verte”, rendez visite à notre site :http://www.lge.com/about/environment/html/Recycling.jspDeutschFrançais
05Regulatory Information cont. Informazioni per la tutela dell’ambienteLa LGE. ha annunciato nel 1994 la cosiddetta 'LGDeclaration for a Cleaner Environment' (Dichiarazione diLG a favore di un ambiente più pulito), un ideale che daallora funge da principio ispiratore della gestioneaziendale. La dichiarazione rappresenta il fondamento checonsente di intraprendere attività a favore dell'ambientetenendo conto degli aspetti economici, ambientali esociali.Noi della LG, promuoviamo attività a favore dellatutela dell'ambiente sviluppando appositamente i nostriprodotti per cogliere il concetto del rispetto dell’ambienteriducendo i materiali dannosi presenti nei nostri prodotti.Ad esempio nei nostri monitor non è presente il cadmio.Informazioni per il riciclaggioIl monitor può presentare componenti che potrebberorisultare eventualmente dannosi per l'ambiente. Èimportante che il monitor sia riciclato al termine del suoutilizzo.La LGE. gestisce tutti i monitor di rifiuto con un metodo diriciclaggio soddisfacente dal punto di vista ambientale. Intutto il mondo sono attualmente in funzione numerosisistemi di riciclaggio e recupero. I diversi componenti sonoriutilizzati e riciclati, mentre le sostanze dannose e i metallipesanti vengono trattati con un metodo rispettosodell’ambiente.Se si desiderano maggiori informazioni in merito alprogramma di riciclaggio, è consigliabile rivolgersi alproprio rivenditore LG o ad un rappresentante aziendaledella LG. Noi della LG impostiamo la nostra visione e le nostrepolitiche a favore di un mondo più pulito ponendo laquestione dell'ambiente dal punto di vista globale comeuna mansione rivolta al miglioramento della nostraazienda. Vi invitiamo a visitare il nostro sito internet perulteriori informazioni sulla nostra politica “verde”.http://www.lge.com/about/environment/html/Recycling.jspInformación para la conservación medioambientalLGE. presentó la 'Declaración para un entorno más limpiode LG' en 1994 y este ideal ha servido para guiar nuestrosprincipios empresariales desde entonces. La Declaraciónes la base que nos ha permitido llevar a cabo tareas querespetan el medio ambiente siempre teniendo en cuentaaspectos sociales, económicos y medioambientales.Promocionamos actividades orientadas a la conservacióndel medio ambiente y desarrollamos nuestros productosespecíficamente para que se ajusten a la filosofía queprotege el entorno. Reducimos al máximo el uso de materiales de riesgo ennuestros productos. Un ejemplo de ello es la ausenciatotal de cadmio en nuestros monitores.Información para el reciclajeEste monitor puede contener piezas que entrañen riesgosmedioambientales. Es importante reciclar este monitordespués de su utilización.LGE. trata todos los monitores usados siguiendo unmétodo de reciclaje que no daña al entorno. Contamoscon diversos sistemas de recuperación y reciclaje quefuncionan a nivel mundial en la actualidad. Es posiblereciclar y reutilizar muchas de las piezas, mientras que lassustancias dañinas y los metales pesados se tratansiguiendo un método que no perjudique al medioambiente. Si desea obtener más información acerca delprograma de reciclaje, póngase en contacto con suproveedor local de LG o con un representante empresarialde nuestra marca. Basamos nuestra visión y nuestras políticas en un mundomás limpio y para ellos optamos por un entorno globalcomo tarea principal de nuestra evolución como empresa.Visite nuestra página Web para obtener más informaciónsobre nuestras políticas ecológicas.http://www.lge.com/about/environment/html/Recycling.jspInformações relacionadas à preservaçãoambientalA LGE. anunciou a 'LG Declaration for a CleanerEnvironment' (Declaração da LG para um ambiente maislimpo) em 1994 e esse ideal tem servido desde entãocomo um princípio administrativo de orientação. ADeclaração é a base que nos tem permitido realizaratividades favoráveis ao ambiente com consideraçãoatenta aos aspectos econômicos, ambientais e sociais.Promovemos atividades de preservação ambiental edesenvolvemos nossos produtos para englobarItalianoEspanõlPortuguês
06Regulatory Information cont. especificamente o conceito de favorável ao ambiente. Reduzimos os materiais perigosos contidos em nossosprodutos. Por exemplo, não há cádmio em nossosmonitores.Informações relacionadas à reciclagemEste monitor pode conter peças que podem representarriscos ao ambiente. É importante que ele seja recicladoapós o uso.A LGE. cuida de todos os monitores descartados atravésde um método de reciclagem agradável ao ambiente. Hávários sistemas de devolução e reciclagem atualmenteem operação no mundo. Muitas peças serão reutilizadase recicladas e as substâncias nocivas e os metaispesados passarão por tratamento através de um métodofavorável ao ambiente.Para obter mais informações sobre nosso programa dereciclagem, entre em contato com seu fornecedor LGlocal ou com um representante corporativo da LG. Definimos nossa visão e nossas políticas relacionadas aum mundo mais limpo selecionando a questão doambiente global como uma tarefa de aprimoramentocorporativo. Visite nosso site para obter mais informaçõessobre nossas políticas de meio ambiente.http://www.lge.com/about/environment/html/Recycling.jspInformatie met betrekking tot het behoud vanhet milieuLGE. publiceerde in 1994 de 'LG Declaration for a CleanerEnvironment' (de LG-verklaring met betrekking tot eenschoner milieu). Deze verklaring en het ideaal van eenschoner milieu fungeren sindsdien als een bestuurlijkeleidraad voor onze onderneming. Op basis van dezeverklaring ontplooien wij milieuvriendelijke activiteiten,waarbij er zowel met sociale en economische aspecten,als met milieuaspecten zorgvuldig rekening wordtgehouden.Wij ondersteunen activiteiten die zijn gericht op hetbehoud van het milieu en wij houden bij het ontwikkelenonze producten specifiek rekening met de milieuvriendelijkheid van onze producten. Wij minimaliseren het gebruik van schadelijke stoffen inonze producten. Er wordt bijvoorbeeld geen cadmiumverwerkt in onze monitors.NederlandsInformatie met betrekking tot recyclingDeze monitor bevat materialen die schadelijk zoudenkunnen zijn voor het milieu. Het is belangrijk dat dezemonitor aan het einde van zijn levensduur wordtgerecycled.LGE. verwerkt alle afvalmonitors via een milieuvriendelijkerecyclingmethode. Hiervoor worden er momenteelwereldwijd verscheidene inname- en recyclingsystemengehanteerd. Een groot aantal onderdelen wordt opnieuwgebruikt en gerecycled, waarbij schadelijke stoffen enzware metalen volgens een milieuvriendelijke methodeworden verwerkt.Voor meer informatie over ons recyclingprogramma kunt ucontact opnemen met uw plaatselijke LG-vertegenwoordiger of een LG-vestiging. Onze visie en ons beleid met betrekking tot een schonerewereld vloeien voort uit het feit dat wij het milieu hebbenaangemerkt als een onderwerp dat speciale aandachtverdient binnen onze onderneming. Bezoek onze websitevoor meer informatie over ons 'groene' beleid.http://www.lge.com/about/environment/html/Recycling.jsp»ÌÙÓχˆËˇ ÔÓ Óı‡Ì ÓÍÛʇ˛˘ÂÈ Ò‰˚¬ 1994 „Ó‰Û ÍÓÔÓ‡ˆËˇ LGE ÓÔÛ·ÎËÍÓ‚‡Î‡'ƒÂÍ·‡ˆË˛ LG ÔÓ Óı‡Ì ÓÍÛʇ˛˘ÂÈ Ò‰˚',ÍÓÚÓ‡ˇ Ò ÚÂı ÔÓ ÒÎÛÊËÚ ÓÒÌÓ‚Ì˚Ï ÔË̈ËÔÓÏÛÔ‡‚ÎÂÌˡ. Õ‡ ÓÒÌÓ‚Â ˝ÚÓÈ ‰ÂÍ·‡ˆËË Ï˚ ÒÏÓ„ÎËÔ‰ÔËÌˇÚ¸ ‰ÂÈÒڂˡ, Ó·ÂÒÔ˜˂‡˛˘Ë ·ÂÁÓÔ‡ÒÌÓÒÚ¸ ÓÍÛʇ˛˘ÂÈ Ò‰˚, Û‰ÂΡˇ ÔË ˝ÚÓωÓÎÊÌÓ ‚ÌËχÌË ˝ÍÓÌÓÏ˘ÂÒÍËÏ, ˝ÍÓÎӄ˘ÂÒÍËÏ ËÒӈˇθÌ˚Ï ‡ÒÔÂÍÚ‡Ï.Ã˚ ÒÚËÏÛÎËÛÂÏ ‰ÂˇÚÂθÌÓÒÚ¸ ÔÓ Óı‡ÌÂÓÍÛʇ˛˘ÂÈ Ò‰˚, Û‰ÂΡˇ ÓÒÓ·Ó ‚ÌËχÌËÂ‡Á‡·ÓÚÍ ̇¯ÂÈ ÔÓ‰Û͈ËË ‚ ÒÓÓÚ‚ÂÚÒÚ‚ËË ÒÍÓ̈ÂÔˆËÂÈ ˝ÍÓÎӄ˘ÂÒÍÓÈ ·ÂÁÓÔ‡ÒÌÓÒÚË. Ã˚ Ò‚Ó‰ËÏ Í ÏËÌËÏÛÏÛ ÒÓ‰ÂʇÌË ÓÔ‡ÒÌ˚ı‚¢ÂÒÚ‚ ‚ ̇¯ÂÈ ÔÓ‰Û͈ËË. Õ‡ÔËÏÂ, ‚ ̇¯ËıÏÓÌËÚÓ‡ı ‚˚ Ì ̇ȉÂÚ ͇‰Ïˡ.»ÌÙÓχˆËˇ ÔÓ ÛÚËÎËÁ‡ˆËË ÓÚıÓ‰Ó‚›ÚÓÚ ÏÓÌËÚÓ ÏÓÊÂÚ ÒÓ‰Âʇڸ ÍÓÏÔÓÌÂÌÚ˚,ÍÓÚÓ˚ ÏÓ„ÛÚ Ì‡ÌÂÒÚË Û˘Â· ÓÍÛʇ˛˘ÂÈ Ò‰Â.Russian
07Regulatory Information cont. EPA(EPA applied model only)ENERGY STARis a set of power-saving guidelinesissued by the U.S. Environmental ProtectionAgency(EPA).NOM MARK (Mexico only)ÕÂÓ·ıÓ‰ËÏÓ ÛÚËÎËÁËÓ‚‡Ú¸ ÏÓÌËÚÓ ÔÓÒÎÂËÒÔÓθÁÓ‚‡Ìˡ.KÓÔÓ‡ˆËˇ LGE ÔÂÂ‡·‡Ú˚‚‡ÂÚ ‚Ò ·‡ÍÓ‚‡ÌÌ˚ÂÏÓÌËÚÓ˚ Ò ÔÓÏÓ˘¸˛ ˝ÍÓÎӄ˘ÂÒÍË ÔËÂÏÎÂÏÓ„ÓÏÂÚÓ‰‡ ÛÚËÎËÁ‡ˆËË ÓÚıÓ‰Ó‚. œÓ ‚ÒÂÏÛ ÏËÛ‰ÂÈÒÚ‚Û˛Ú ÒËÒÚÂÏ˚ ÛÚËÎËÁ‡ˆËË ÓÚıÓ‰Ó‚ Ë ‚ÓÁ‚‡Ú‡ËÒÔÓθÁÓ‚‡ÌÌÓÈ ÔÓ‰Û͈ËË. ÃÌÓ„Ë ÍÓÏÔÓÌÂÌÚ˚·Û‰ÛÚ ‚ÚÓ˘ÌÓ ËÒÔÓθÁÓ‚‡Ì˚ Ë ÛÚËÎËÁËÓ‚‡Ì˚, ‚ ÚÓ‚ÂÏˇ Í‡Í ‚‰Ì˚ ‚¢ÂÒÚ‚‡ Ë ÚˇÊÂÎ˚ ÏÂÚ‡ÎÎ˚·Û‰ÛÚ Ó·‡·ÓÚ‡Ì˚ Ò ÔÓÏÓ˘¸˛ ˝ÍÓÎӄ˘ÂÒÍËÔËÂÏÎÂÏÓ„Ó ÏÂÚÓ‰‡.«‡ ·ÓΠÔÓ‰Ó·ÌÓÈ ËÌÙÓχˆËÂÈ ÔÓ Ì‡¯ÂÈÔÓ„‡ÏÏ ÛÚËÎËÁ‡ˆËË ÓÚıÓ‰Ó‚ Ó·‡˘‡ÈÚÂÒ¸ ÍÏÂÒÚÌÓÏÛ ÔÓÒÚ‡‚˘ËÍÛ ËÎË Ô‰ÒÚ‡‚ËÚÂβ ÍÓÔÓ‡ˆËË LG. Ã˚ ÓËÂÌÚËÛÂÏÒˇ ̇ Ó·ÂÒÔ˜ÂÌË ˝ÍÓÎӄ˘ÂÒÍÓÈ·ÂÁÓÔ‡ÒÌÓÒÚË, ÒÚ‡‚ˇ Ò· ˆÂθ˛ „ÎÓ·‡Î¸ÌÛ˛ Á‡˘ËÚÛÓÍÛʇ˛˘ÂÈ Ò‰˚. ƒÓÔÓÎÌËÚÂθÌÛ˛ ËÌÙÓχˆË˛Ó ̇¯ÂÈ ÔÓÎËÚËÍ ÔÓ Óı‡Ì ÓÍÛʇ˛˘ÂÈ Ò‰˚ ‚˚ÏÓÊÂÚ ̇ÈÚË Ì‡ ̇¯ÂÏ Ò‡ÈÚÂ:http://www.lge.com/about/environment/html/Recycling.jspAs an ENERGY STAR Partner LGE U. S.A.,Inc. has determined that this productmeets the ENERGY STAR guidelines forenergy efficiency.
08Regulatory Information cont. 1.When this crossed-out wheeled bin symbol is attachedto a product it means the product is covered by theEuropean Directive 2002/96/EC. 2.All electrical and electronic products should bedisposed of separately from the municipal wastestream via designated collection facilities appointed bythe government or the local authorities. 3.The correct disposal of your old appliance will helpprevent potential negative consequences for theenvironment and human health.4.For more detailed information about disposal of yourold appliance, please contact your city office, wastedisposal service or the shop where you purchased theproduct.Disposal of your old appliance1.Quando su un prodotto è riportato il simbolo di1.När den här symbolen med en överkryssadsoptunna på hjul sitter på en produkt innebär detatt den regleras av European Directive2002/96/EC.2.Alla elektriska och elektroniska produkter börkasseras via andra vägar än de som finns förhushållsavfall, helst via för ändamålet avseddauppsamlingsanläggningar som myndigheternautser.3.Om du kasserar din gamla apparat på rätt sättså bidrar du till att förhindra negativakonsekvenser för miljön och människors hälsa.4.Mer detaljerad information om kassering av dingamla apparat kan får av kommunen,renhållningsverket eller den butik där du köpteprodukten.1.Als het symbool met de doorgekruiste verrijdbareafvalbak op een product staat, betekent dit dathet product valt onder de Europese Richtlijn2002/96/EC.2.Elektrische en elektronische producten mogenniet worden meegegeven met het huishoudelijkafval, maar moeten worden ingeleverd bijspeciale inzamelingspunten die door de lokale oflandelijke overheid zijn aangewezen.3.De correcte verwijdering van uw oude toestelhelpt negatieve gevolgen voor het milieu en demenselijke gezondheid voorkomen.Smaltimento delle apparecchiature obsoleteKassering av din gamla apparatUw oude toestel wegdoen1.Ce symbole, représentant une poubelle surroulettes barrée d'une croix, signifie que leproduit est couvert par la directive européenne2002/96/EC.2.Les éléments électriques et électroniquesdoivent être jetés séparément, dans les vide-ordures prévus à cet effet par votre municipalité. 3.Une élimination conforme aux instructions aideraà réduire les conséquences négatives et risqueséventuels pour l'environnement et la santéhumaine.4.Pour plus d'information concernant l'éliminationde votre ancien appareil, veuillez contacter votremairie, le service des ordures ménagères ouencore la magasin où vous avez acheté ceproduit.Élimination de votre ancien appareilun bidone della spazzatura barrato da una crocesignifica che il prodotto è coperto dalla direttivaeuropea 2002/96/EC.2.Tutti i prodotti elettrici ed elettronici dovrebberoessere smaltiti separatamente rispetto allaraccolta differenziata municipale, medianteimpianti di raccolta specifici designati dalgoverno o dalle autorità locali.3.Il corretto smaltimento delle apparecchiatureobsolete contribuisce a prevenire possibiliconseguenze negative sulla salute umana esull'ambiente.4.Per informazioni più dettagliate sullo smaltimentodelle apparecchiature obsolete, contattare ilcomune, il servizio di smaltimento rifiuti o ilnegozio in cui è stato acquistato il prodotto. EnglishFrenchItalianSwedishDutchWEEE (for Europe )
Regulatory Information cont. 091.Wenn dieses Symbol eines durchgestrichenenAbfalleimers auf einem Produkt angebracht ist,unterliegt dieses Produkt der europäischenRichtlinie 2002/96/EC.2.Alle Elektro- und Elektronik-Altgeräte müssengetrennt vom Hausmüll  über dafür staatlichvorgesehenen Stellen entsorgt werden.3.Mit der ordnungsgemäßen Entsorgung des altenGeräts vermeiden Sie Umweltschäden und eineGefährdung der persönlichen Gesundheit. 4.Weitere Informationen zur Entsorgung des altenGeräts erhalten Sie bei der Stadtverwaltung,beim Entsorgungsamt oder in dem Geschäft, woSie das Produkt erworben haben. 1.ŸÙ·Ó ¤Ó· ÚÔ˚fiÓ ‰È·ı¤ÙÂÈ ÙÔ ‰‡Ì‚ÔÏÔ ÂÓfi˜‰È·ÁÚ·Ì̤ÓÔ˘ οϷıÔ˘ ·ÔÚÚÈÌÌ¿ÙˆÓ, ÙfiÙ ÙÔ ÚÔ˚fiÓηχÙÂÙ·È ·fi ÙËÓ E˘Úˆ·˚΋ O‰ËÁ›· 2002/96/EOK.2.H ·fiÚÚÈ„Ë fiÏˆÓ ÙˆÓ ËÏÂÎÙÚÈÎÒÓ Î·È ËÏÂÎÙÚÔÓÈÎÒÓÚÔ˚fiÓÙˆÓ Ú¤ÂÈ Ó· Á›ÓÂÙ·È ¯ˆÚÈÛÙ¿  ·fi Ù· ÁÂÓÈοÔÈÎȷο ·ÔÚÚ›ÌÌ·Ù· ̤ۈ ηıÔÚÈṲ̂ӈÓÂÁηٷÛÙ¿ÛÂˆÓ Û˘ÏÏÔÁ‹˜ ·ÔÚÚÈÌÌ¿ÙˆÓ, ÔÈ Ôԛ˜¤¯Ô˘Ó ‰ËÌÈÔ˘ÚÁËı› ›Ù ·fi ÙËÓ Î˘‚¤ÚÓËÛË ‹ ·fi ÙȘÙÔÈΤ˜ ·Ú¯¤˜.3.H ÛˆÛÙ‹ ·fiÚÚÈ„Ë Ù˘ ·ÏÈ¿˜ Û·˜ Û˘Û΢‹˜ ı·‚ÔËı‹ÛÂÈ ÛÙËÓ ·ÔÙÚÔ‹ Èı·ÓÒÓ ·ÚÓËÙÈÎÒÓ Û˘ÓÂÈÒÓˆ˜ ÚÔ˜ ÙÔ ÂÚÈ‚¿ÏÏÔÓ Î·È ÙËÓ ˘Á›· ÙÔ˘ ·ÓıÚÒÔ˘.4.°È· ÈÔ ÏÂÙÔÌÂÚ›˜ ÏËÚÔÊÔڛ˜ Û¯ÂÙÈο Ì ÙËÓ·fiÚÚÈ„Ë Ù˘ ·ÏÈ¿˜ Û·˜ Û˘Û΢‹˜, ÂÈÎÔÈÓˆÓ‹ÛÙ ÌÂÙÔ ·ÚÌfi‰›Ô ÙÔÈÎfi ÁÚ·Ê›Ô, ˘ËÚÂÛ›· ‰È¿ıÂÛ˘ ÔÈÎÈ·ÎÒÓ·ÔÚÚÈÌÌ¿ÙˆÓ ‹ ÙÔ Ì·Á·Í› ·fi ÙÔ ÔÔ›Ô ·ÁÔÚ¿Û·Ù ÙÔÚÔ˚fiÓ.1.Tämä merkki tuotteessa tarkoittaa, että tuotekuuluu sähkö- ja elektroniikkalaiteromustaannetun EU-direktiivin 2002/96/EYsoveltamisalaan.2.Kaikki elektroniset laitteet ovat ongelmajätettä, joten ne on toimitettava paikalliseenkeräyspisteeseen.3.Vanhan laitteen asianmukainen hävittäminen ehkäisee mahdollisia ympäristöön ja terveyteen kohdistuvia haittavaikutuksia.4.Lisätietoa vanhan laitteen hävittämisestä saat ottamalla yhteyden paikallisiin viranomaisiin,kierrätyskeskukseen tai myymälään, josta ostit laitteen.1.Når der er et tegn med et kryds over enskraldespand, betyder det, at produktet eromfattet af EU-direktiv 2002/96/EC.2.Alle elektriske og elektroniske produkter skalsmides ud et andet sted end gennem denkommunale affaldsordning ved hjælp af specielleindsamlingsfaciliteter, der er organiseret af staten1.Si en un producto aparece el símbolo de un contenedorde basura tachado, significa que éste se acoge a laDirectiva 2002/96/CE.2.Todos los aparatos eléctricos o electrónicos se debendesechar de forma distinta del servicio municipal derecogida de basura, a través de puntos de recogidadesignados por el gobierno o las autoridades locales.3.La correcta recogida y tratamiento de los dispositivosinservibles contribuye a evitar riesgos potenciales para elmedio ambiente y la salud pública.4.Para obtener más información sobre cómo deshacerse desus aparatos eléctricos y electrónicos viejos, póngase encontacto con su ayuntamiento, el servicio de recogida debasuras o el establecimiento donde adquirió el producto. Vanhojen laitteiden hävittäminenEntsorgung von AltgerätenSådan smider du dit gamle apparat ud∞fiÚÚÈ„Ë Ù˘ ·ÏÈ¿˜ Û·˜ Û˘Û΢‹˜Cómo deshacerse de aparatos eléctricos yelectrónicos viejoseller de lokale myndigheder.3.Korrekt bortskaffelse af dit gamle apparat er medtil at forhindre mulige skadevirkninger på miljøetog menneskelig sundhed. 4.Mere detaljerede oplysninger om bortskaffelse afdit gamle apparat kan fås ved at kontakte ditlokale kommunekontor, renovationsselskab ellerden butik, hvor du købte produktet. FinnishGermanDanishGreekSpanish4.Wilt u meer informatie over de verwijdering vanuw oude toestel? Neem dan contact op met uwgemeente, de afvalophaaldienst of de winkelwaar u het product hebt gekocht.
Regulatory Information cont. 10                        PortugueseSlovakCzechCroatianHungarianPolish
                  Regulatory Information cont. 11EstonianLatvianLithuanian

Navigation menu