LG Electronics USA 3G1XOUTBTS STAREX-IS 1900 Outdoor BTS User Manual STAREX IS User s Manual
LG Electronics USA STAREX-IS 1900 Outdoor BTS STAREX IS User s Manual
Contents
- 1. Users Manual Part 1
- 2. Users Manual Part 2
- 3. Users Manual Part 3
- 4. Users Manual Part 4
- 5. Users Manual Part 5
Users Manual Part 4
STAREX-IS BSM Manual 4.9.6.3. Directions for Use The direction is configured with full of drawings. Refer to the STMX, TRMX Block for detailed operation. Press stmGUI among the buttons of Manager. Fig. 4.9-16 stmGUI Start Icon Then the following screen is displayed. Fig. 4.9-17 stmGUI Main Screen SMD-011-PMA210 Page:564(877) Issue:1.0 STAREX-IS BSM Manual The figure above shows the status that the highest-grade alarm of the BSC0 is the critical alarm and the highest alarm of the BTS0, major alarm, is generated. 4.9.6.3.1. BTS Name Display. Fig. 4.9-18 Display Screen of BTS Name. e.g.) On the figure above, ghjeong is the real name of the BTS and BTS 0 is the BTS ID. 4.9.6.3.2. Main Menu Fig. 4.9-19 Main Menu Hide : It is used when hiding RACK and SHELF simultaneously from the screen. Update : It is used in compulsory loading of initial value upon deletion and extension by MMC. Exit : It ends the program. 4.9.6.3.3. Color by the Alarm Grade Fig. 4.9-20 Alarm Color Red : Critical Orange : Major Green : Minor Azure : Normal SMD-011-PMA210 Page:565(877) Issue:1.0 STAREX-IS BSM Manual Gray : BTS Is Not Equipped SMD-011-PMA210 Page:566(877) Issue:1.0 STAREX-IS BSM Manual 4.9.6.3.4. Status Color. Fig. 4.9-21 Status Color Tone 4.9.6.3.5. Processor Status Dual Processor Normal Single Processor A Side Active Fig. 4.9-22 Processor Status (CAN) Fig. 4.9-23 Processor Status (BSC) SMD-011-PMA210 Page:567(877) Issue:1.0 STAREX-IS BSM Manual Fig. 4.9-24 Processor Status (BTS) 4.9.6.3.6. Rack View To see the shape of BSC/BTS one should press the corresponding button. Select a BSC. Fig. 4.9-25 BSC Selection Select a BTS. Fig. 4.9-26 BTS Selection SMD-011-PMA210 Page:568(877) Issue:1.0 STAREX-IS BSM Manual 4.9.6.3.7. Rack Shape Diagram. The following shape appears if CAN, BSC or BTS is chosen. 4.9.6.3.7.1. CAN Rack Fig. 4.9-27 CAN Rack Shape. The color of each slot manifests the alarm information of equipped cards. For example, the yellow color of BCRA, PIPA and FERA in the 4th shelf of the left side shows that the alarm is generating at Major status. SMD-011-PMA210 Page:569(877) Issue:1.0 STAREX-IS BSM Manual 4.9.6.3.7.2. BSC Rack Fig. 4.9-28 BSC Rack SMD-011-PMA210 Page:570(877) Issue:1.0 STAREX-IS BSM Manual 4.9.6.3.7.3. BTS Rack Fig. 4.9-29 BTS Rack SMD-011-PMA210 Page:571(877) Issue:1.0 STAREX-IS BSM Manual 4.9.6.3.7.4. Slot Shape Diagram. The corresponding dialog box is displayed upon clicking slot in the rack shape diagram. click Fig. 4.9-30 card click example. The following dialog box appears upon clicking SLPA card above. Board name Alarm Info 정보 Status 상태 정보 Info Alarm message Shape Info 형상Location 위치 정보 Time memo Fig. 4.9-31 e.g.)Dialog box- card Information Memo: Stores the edited results temporarily. Edit: Edit button SMD-011-PMA210 Page:572(877) Issue:1.0 STAREX-IS BSM Manual Cancel: End button Save: Stores the edited. 1,2,3,4,5 button: The memo is stored in numerical order. Click numbers in right side(1,2,3,4,5) to see the memo. Fig. 4.9-32 e.g.)Dialog box-Vocoder Element Status For example, the SK_Qcelp type call in the VCE0 of DSP1 is in busy status. Fig. 4.9-33 e.g.)Dialog box-DBPA Chip Status SMD-011-PMA210 Page:573(877) Issue:1.0 STAREX-IS BSM Manual 4.9.6.3.7.5. Status Display Fig 4.9-34 Display Status by Board 4.9.6.3.7.6. Alarm Display Fig. 4.9-35 Alarm Display by Board. 4.9.6.4. Suggestions on Operation. 4.9.6.4.1. Status Management The status and alarm are displayed in turn at 2-minute intervals in managing each board. If there is no Alarm it displays the status color. 4.9.6.4.2. The Order of Priority The stmGUI receives the process results of the status block (STMX) and fault block (TRMX) to reprocess them. Therefore, both of the two blocks should be normally operated for the normal operation. If the initial data setup of STMX has not been done while BSM is running, stmGUI may display undefined values. In this case, press update SMD-011-PMA210 Page:574(877) Issue:1.0 STAREX-IS BSM Manual button to initialize the value again. SMD-011-PMA210 Page:575(877) Issue:1.0 STAREX-IS BSM Manual 4.9.6.4.3. End Use Exit button in the main screen to end the program. It is undesirable using command kill or xkill. Proper procedure is recommended. 4.9.7. Neighbor Control Window (neighbor) 4.9.7.1. Overview. Graphic neighbor is a tool that helps addition and deletion of the information related to the BTS neighbor. User can view, add and delete the information related to neighbor using the existing MMC but it requires the user to input lots of data. Therefore, graphic neighbor minimize the input amount of user for user’s convenience. 4.9.7.2. Environment Setup. Refer to the environment setup of stmGUI. 4.9.7.3. Directions for Use Most of the directions are constituted of drawings and refer to the CDMX for detailed operation. Press neighbor among the buttons of Manager to start. Fig. 4.9-36 Neighbor Start Icon The following initial screen appears. SMD-011-PMA210 Page:576(877) Issue:1.0 STAREX-IS BSM Manual Fig. 4.9-36 Neighbor Initial Screen SMD-011-PMA210 Page:577(877) Issue:1.0 STAREX-IS BSM Manual 4.9.7.3.1. Main Menu Fig. 4.9-37 Main Menu Screen User can select a function in this screen. Select : select or change the BTS or sector. For selection, select a BTS first and then select a sector in the BTS. Delete : delete the neighbor in the presently selected sector. Press sector to be deleted after selection. Add : add neighbor into the presently selected sector. Press a sector to be added after selection. NewAdd : add a neighbor of other MSC into the presently selected sector. Input information into the window field appeared after selection. (There is no default value) 4.9.7.3.2. BTS Selection There are two methods for selecting BTS. Surely, the BTS subjected to the MSC of the presently operating system can be selected. 4.9.7.3.2.1. Method using Map. Fig. 4.9-38 Full Map Dragging mouse can search the desired location here. Click BTS (label : x-y ) in the SMD-011-PMA210 Page:578(877) Issue:1.0 STAREX-IS BSM Manual desired location with this method and press the sector of the BTS to select. 4.9.7.3.2.2. Selection Method by BTS ID. Fig. 4.9-39 Random BTS Selection BSC : It is the BSC to which the BTS belongs. BTS : It is the BTS ID of the BTS. Press OK button to complete the selection. 4.9.7.3.2.3. Selection Example. Fig.4.9-40 Initial Screen (Before selecting BTS ) Fig. 4.9-41 After selecting BTS. Fig. 4.9-42 After selecting Sector(Green: neighbor). SMD-011-PMA210 Page:579(877) Issue:1.0 STAREX-IS BSM Manual 4.9.7.3.3. Neighbor Information BSC ID BTS ID Selected Sector Neighbor Neighbor Information Selected BSC,BTS Selected Sector Information Fig. 4.9-43 Neighbor Information Screen The own neighbor list checking is possible through the information in the lower part or the green tinted sector. SMD-011-PMA210 Page:580(877) Issue:1.0 STAREX-IS BSM Manual 4.9.7.3.4. Neighbor Addition The following window appears after selecting neighbor to be added. Fig. 4.9-44 Inputting neighbor belongs to mother MSC Adding neighbor belongs to the mother MSC requires the user to input just 4~6 fields. Fig. 4.9-45 Inputting neighbor belongs to other MSC SMD-011-PMA210 Page:581(877) Issue:1.0 STAREX-IS BSM Manual Adding neighbor belongs to other MSC requires the user to input all the information. Fig. 4.9-46 Default Value upon Input Select a field to be input then the system shows the default values. To select a value input the value onto the corresponding input space or select one among the values in the lower part with mouse. Press OK after the input is done or press Cancel to return to the Main screen. 4.9.7.3.5. Neighbor Deletion Deletion can be completed with two kinds of method. Press the corresponding line in the lower part or press the BTS sector button. 4.9.7.4. Suggestions in Operation 4.9.7.4.1. The order of priority Graphic Neighbor is a tool for adding/deleting neighbors. Therefore, performing extension or deletion with MMC can bring out a wrong result while the Graphic Neighbor is being used. And if it is performed the user should run the Graphic Neighbor once again. The neighbor intercommunicates with the configuration block (CDMX) through MMI block. Consequently, the two blocks should be in normal operation. SMD-011-PMA210 Page:582(877) Issue:1.0 STAREX-IS BSM Manual 4.9.8. Call Trace Window 4.9.8.1. Overview. Call Trace Window is a tool that shows all kinds of call trace information for a specific for a specific MS onto the GUI (Graphic User Interface) screen of the user’s terminal. Call trace command can be executed and the results can be checked through the existing MMC or dedicated window for call trace. The user can set time as long as he want with Timer for the maximum of two MS to trace calls. 4.9.8.2. Environment Setup Refer to the environment setup of stmGUI 4.9.8.3. Directions for Use. Most of the directions are constituted of drawings and refer to the TSMX Block for detailed operation. Press call among the buttons of Manager to start. Fig. 4.9-47 Call Trace Start Icon Then the following screen appears. SMD-011-PMA210 Page:583(877) Issue:1.0 STAREX-IS BSM Manual Fig. 4.9-48 Call Trace Initial Screen SMD-011-PMA210 Page:584(877) Issue:1.0 STAREX-IS BSM Manual 4.9.8.3.1. Sub Menu. 단말 고유 넘버 단말번호 Packet Zone Id Service option Frame Offset CDMA CH Release Reason Round Trip Delay User Zone ID Forward Radio Configuration 착신측번호 Reverse Radio Config Fig. 4.9-49 Call Information. Forwad side Reverse side Forward Frame Error Rate Reverse Frame Error Rate Traffic Channel Gain 신호대 잡음비 Forward Power Control Fig. 4.9-50 Call Quality SMD-011-PMA210 Page:585(877) Issue:1.0 STAREX-IS BSM Manual 기지국 정보 Forward Quais Orgonal Function Reverse Supplement CHannel Forward Walsh Forward Supplement CHannel 섹터 정보 Reverse Walsh Fig. 4.9-51 SCH Information Forward data rate Total Reverse data rate Reverse data rate Total Forward data rate Packet State (Dormant or Active) Fig. 4.9-52 Packet Data Information 단말번호 BSC ID BTS ID Trace Time FER Report Interval Time Fig. 4.9-53 Command Window SMD-011-PMA210 Page:586(877) Issue:1.0 STAREX-IS BSM Manual Input MS number (IMSI), BSC ID, BTS ID, Trace Time and FER Report Interval Time into the command window of [Fig. 4.8-53], and press Go Trace button below, then the call trace starts. Press Stop Operation beside Go Trace button to stop the process during the operation and press Exit Program to end call trace program. The Expand Flow shows the flow to the PDSN upon clicking it. Click !! 2개로 분할된 window Fig. 4.9-54 Example of Expand Flow Button If the user wants to see the expand flow hidden by the window at the right side after call test, click Expand Flow button to see the expand flow. SMD-011-PMA210 Page:587(877) Issue:1.0 STAREX-IS BSM Manual 하나로 통합된 window Click !! Fig. 4.9-55 Example of Shrink Flow Button To see the hidden window (Call Information, Call Quality, Handoff Activity at the right) click Shrink Flow button. SMD-011-PMA210 Page:588(877) Issue:1.0 STAREX-IS BSM Manual 4.9.8.3.2. Voice Call 4.9.8.3.2.1. Origination Call (Voice Call Setup / Origination) ----- Fig. 4.9-56 Voice Call Setup / Origination It is FLOW that shows voice originating call process procedure and System Information, Call Information and Call Quality Information are represented on it. The handoff information is also represented when the handoff is generated. SMD-011-PMA210 Page:589(877) Issue:1.0 STAREX-IS BSM Manual 4.9.8.3.2.2. Termination Call.( Voice Call Setup / Termination) ----- Fig. 4.9-57 Voice Call Setup / Termination It is FLOW that shows the voice originating call process procedure, and System Information, Call Information and Call Quality Information are represented on it. The handoff information is also represented when the handoff is generated. SMD-011-PMA210 Page:590(877) Issue:1.0 STAREX-IS BSM Manual 4.9.8.3.3. Data Call 4.9.8.3.3.1. Packet Data Call Setup ----- Fig 4.9-58 Packet Data Call Setup It is FLOW that shows packet data call processing procedure and the System Information, Call Information, Call Quality, Supplemental Channel Information and Packet Data Information are represented on it. The handoff information is also represented on it when the handoff is generated. SMD-011-PMA210 Page:591(877) Issue:1.0 STAREX-IS BSM Manual 4.9.8.3.3.2. Packet Data Call Reactivation / Network Initiated ----- Fig. 4.9-59 Packet Data Call Reactivation / Network Initiated It is FLOW that shows processing procedure of the packet data call which fell into the dormant status and then be reactivated by the network side. The System Information, Call Information, Call Quality, Supplemental Channel Information and Packet Data Information are represented. The handoff information is also represented on it when the handoff is generated. SMD-011-PMA210 Page:592(877) Issue:1.0 STAREX-IS BSM Manual 4.9.8.3.3.3. Packet Data Call Reactivation / MS Initiated ----- Fig. 4.9-60 Packet Data Call Reactivation / MS Initiated It is FLOW that shows the process procedure of packet data call which fell into the dormant status and then reactivated by the MS; the System Information, Call Information, Call Quality, Supplemental Channel Information and Packet Data Information are represented on it. The handoff information is also represented on it when the handoff is generated. SMD-011-PMA210 Page:593(877) Issue:1.0 STAREX-IS BSM Manual 4.9.9. BTS Address Search Window. 4.9.9.1. Overview. The BTS address search program provides the following functions: 1) it can search the corresponding BTS name and address with BSC and BTS number. 2) it can search BSC and BTS number and address with BTS name. 3) it can search BSC and BTS number and name with BTS address. 4.9.9.2. Environment Setup. It use Solaris 2.7 and Informix 7.3.1 as OS. 4.9.9.2.1. Data Files bts_name.info : the file contains BTS name and address 4.9.9.3. Directions for Use. The initial condition is scheduled to configure in the future. SMD-011-PMA210 Page:594(877) Issue:1.0 STAREX-IS BSM Manual 질의 window. Result window. Search Button BSC,BTS ID로 검색시 사용 검색하기 위한 입력필드 Fig. 4.9-61 BTS Address Search Window Initial Screen 4.9.9.3.1. File Information Display Enter !! Fig. 4.9-62 File Information Display SMD-011-PMA210 Page:595(877) Issue:1.0 STAREX-IS BSM Manual Press Enter key on any place of the input field to display the file information on the result window. 4.9.9.3.2. Searching with BSC ID. BSC ID BTS ID 기지국이름 기지국 주소 Fig. 4.9-63 Searching with BSC Input desired BSC number and press Enter key to display the result on the result window when searching with BSC_ID. 4.9.9.3.3. Searching by BTS ID. Fig. 4.9-64 Searching by BTS SMD-011-PMA210 Page:596(877) Issue:1.0 STAREX-IS BSM Manual Input desired BTS number and press Enter key to display the result on the result window when searching with BTS_ID. 4.9.9.3.4. Searching with BTS name. 접두어(Prefix)검색. Fig. 4.9-65 Searching with BTS name-1 접두어(Prefix)검색. Fig. 4.9-66 Searching with BTS name-2 If the user input name into the name input field when searching with BTS name, the searching is performed with real-time prefix. For example, the names start with “s” are displayed upon inputting “s”, the names start with “sad” are displayed upon inputting “sad”. SMD-011-PMA210 Page:597(877) Issue:1.0 STAREX-IS BSM Manual 4.9.9.3.5. Searching with BTS address. 단어로 검색. Fig. 4.9-67 Searching with BTS Address-1 단어로 검색. Fig. 4.9-68 Searching with BTS Address-2 The BTS addresses are searched with real-time words upon inputting address into the address input field when searching with BTS address. For example, the addresses start with “dong” are displayed upon inputting “dong”, and the addresses start with SMD-011-PMA210 Page:598(877) Issue:1.0 STAREX-IS BSM Manual “dongj” are displayed upon inputting “dongj”. SMD-011-PMA210 Page:599(877) Issue:1.0 STAREX-IS BSM Manual 4.9.9.3.6. Searching with Search Button. Search Button Click ! Fig. 4.9-69 Searching with Search Button. Search Button provides the following functions: 1) simultaneous searching for BSC_ID and BTS_ID 2) single searching for BSC_ID or BTS_ID 4.9.9.4. Suggestions for Operation. 4.9.9.4.1. The Order of Priority. BTS address searching program is a graphic tool that provides the following function: 1) searching BTS name and address with BSC ID and BTS ID, 2) searching BSC ID, BTS ID, and address with name, 3) searching BSC ID, BTS ID, and name with address. The address search program should be rerun when inserting, deleting or modifying the data of the bts_name.info file that includes BTS information. The Informix should be normally run because the Informix db is used for searching. SMD-011-PMA210 Page:600(877) Issue:1.0
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.3 Linearized : No Create Date : 2001:10:18 13:13:24+09:00 Modify Date : 2001:11:09 11:14:17-05:00 Page Count : 37 Creation Date : 2001:10:18 04:13:24Z Mod Date : 2001:10:18 04:13:24Z Producer : Acrobat Distiller 5.0 (Windows) Author : LG IBM PC USER Metadata Date : 2001:10:18 04:13:24Z Creator : LG IBM PC USER Title : Microsoft Word - STAREX-IS User's Manual.docEXIF Metadata provided by EXIF.tools