LG Electronics USA 42LE5300UC LED LCD TV User Manual G User s manual
LG Electronics USA LED LCD TV G User s manual
Users Manual
Order Number : GETEC-C1-10-077 FCC Part 15 subpart B Test Report Number : GETEC-E3-10-035 Page 1 / 1 APPENDIX G : USERâS MANUAL EUT Type: LED LCD TV/Monitor FCC ID.: BEJ42LE5300UC OWNERâS MANUAL LED LCD TV / LCD TV Please read this manual carefully before operating your set and retain it for future reference. The model and serial number of the TV is located on the back and one side of the TV. Record it below should you ever need service. MODEL SERIAL P/NO : SAC34134204 (1003-REV04) www.lge.com WARNING / CAUTION WARNING / CAUTION To prevent fire or shock hazards, do not expose this product to rain or moisture. TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated âdangerous voltageâ within the productâs enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING/CAUTION TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. NOTE TO CABLE/TV INSTALLER This reminder is provided to call the CATV system installerâs attention to Article 820-40 of the National Electric Code (U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of the cable entry as practical. FCC Notice Class B digital device This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause (harmful) interference, and (2) this device must accept any interference received, including interference that may cause undesired operation (of the device). Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void the userâs authority to operate the equipment. CAUTION Do not attempt to modify this product in any way without written authorization from LG Electronics. Unauthorized modification could void the userâs authority to operate this product. SAFETY INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS Read these instructions. Keep these instructions. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. Only use attachments/accessories specified by the manufacturer. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/ apparatus combination to avoid injury from tip-over. Unplug this apparatus during lighting storms or when unused for long periods of time. 10 Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with dry cloth. Do not block any ventilation openings. Install in accordance with the ma nufacturerâs instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong, The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. SAFETY INSTRUCTIONS 11 Never touch this apparatus or antenna during a thunder or lighting storm. 12 When mounting a TV on the wall, make sure not to install the TV by the hanging power and signal cables on the back of the TV. 13 Do not allow an impact shock or any objects to fall into the product, and do not drop onto the screen with something. 14 CAUTION concerning the Power Cord: It is recommend that appliances be placed upon a dedicated circuit; that is, a single outlet circuit which powers only that appliance and has no additional outlets or branch circuits. Check the specification page of this owner's manual to be certain. Do not connect too many appliances to the same AC power outlet as this could result in fire or electric shock. Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords, frayed power cords, or damaged or cracked wire insulation are dangerous . Any of these conditions could result in electric shock or fire. Periodically examine the cord of your appliance, and if its appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have the cord replaced with an exact replacement part by an authorized servicer. Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the appliance. Do not use a damaged or loose power cord. Do not pull on the power cord to unplug the TV. Grasp the plug when unplugging the power cord. 15 WARNING - To reduce the risk of fire or electrical shock, do not expose this product to rain, moisture or other liquids. Do not touch the TV with wet hands. Do not install this product near flammable objects such as gasoline or candles or expose the TV to direct air conditioning. 16 Do not expose to dripping or splashing and do not place objects filled with liquids, such as vases, cups, etc. on or over the apparatus (e.g. on shelves above the unit). 17 GROUNDING Ensure that you connect the earth ground wire to prevent possible electric shock (i.e. a TV with a three-prong grounded AC plug must be connected to a three-prong grounded AC outlet). If grounding methods are not possible, have a qualified electrician install a separate circuit breaker. Do not try to ground the unit by connecting it to telephone wires, lightening rods, or gas pipes. Power Supply Short-circuit Breaker 18 DISCONNECTING DEVICE FROM MAINS Mains plug is the disconnecting device. The plug must remain readily operable. 19 As long as this unit is connected to the AC wall outlet, it is not disconnected from AC power even if you turn off the power switch on the unit. 20 ANTENNAS Outdoor antenna grounding If an outdoor antenna is installed, follow the precautions below. An outdoor antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can come in contact with such power lines or circuits as death or serious injury can occur. Be sure the antenna system is grounded so as to provide some protection against voltage surges and built-up static charges. Section 810 of the National Electrical Code (NEC) in the U.S.A. provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes and requirements for the grounding electrode. 23 Ventilation Install your TV where there is proper ventilation. Do not install in a confined space such as a bookcase. Do not cover the product with cloth or other materials (e.g.) plastic while plugged in. Do not install in excessively dusty places. 24 Take care not to touch the ventilation openings. When watching the TV for a long period, the ventilation openings may become hot. 25 If you smell smoke or other odors coming from the TV or hear strange sounds, unplug the power cord contact an authorized service center. 26 Do not press strongly upon the panel with hand or sharp object such as nail, pencil or pen, or make a scratch on it. 27 Keep the product away from direct sunlight. 28 If the TV feels cold to the touch, there may be a small âflickerâ when it is turned on. This is normal, there is nothing wrong with TV. Some minute dot defects may be visible on the screen, appearing as tiny red, green, or blue spots. However, they have no adverse effect on the monitor's performance. Avoid touching the LCD screen or holding your finger(s) against it for long periods of time. Doing so may produce some temporary distortion effects on the screen. Antenna grounding according to the National Electrical Code, ANSI/NFPA 70 Ground Clamp Antenna Lead in Wire Antenna Discharge Unit (NEC Section 810-20) Electric Service Equipment Grounding Conductor (NEC Section 810-21) Ground Clamps Power Service Grounding Electrode System (NEC Art 250, Part H) NEC: National Electrical Code 21 22 Cleaning When cleaning, unplug the power cord and rub gently with a soft cloth to prevent scratching. Do not spray water or other liquids directly on the TV as electric shock may occur. Do not clean with chemicals such as alcohol, thinners or benzene. Moving Make sure the product is turned off, unplugged and all cables have been removed. It may take 2 or more people to carry larger TVs. Do not press against or put stress on the front panel of the TV. ON DISPOSAL (Only Hg lamp used LCD TV) The fluorescent lamp used in this product contains a small amount of mercury. Do not dispose of this product with general household waste. Disposal of this product must be carried out in accordance to the regulations of your local authority. CONTENTS WARNING / CAUTION ............................... 2 SAFETY INSTRUCTIONS Important Safety Instructions.............................. 3 FEATURE OF THIS TV ................................ 8 PREPARATION Accessories .............................................................9 Front Panel Information ..................................... 11 Back Panel Information .....................................16 Stand Instructions ...............................................20 VESA wall mounting .........................................28 Cable Management ..........................................30 Desktop Pedestal Installation .........................32 Swivel Stand ........................................................32 Kensington Security System ..........................32 Attaching the TV to a Desk ............................33 Securing the TV to the Wall to Prevent Falling when the TV is used on a stand ...................34 Antenna or Cable Connection .......................35 EXTERNAL EQUIPMENT SETUP HD Receiver setup .............................................36 DVD setup ............................................................39 VCR SETUP .......................................................... 41 Other A/V Source Setup .................................42 USB Connection ................................................43 Headphone Setup ............................................43 Audio out Connection ......................................44 PC Setup ..............................................................45 WATCHING TV / CHANNEL CONTROL Remote Control Functions ..............................52 Turning on the TV ..............................................54 Channel Selection..............................................54 Volume Adjustment ..........................................54 Initial Setting .......................................................55 On-Screen Menus Selection .......................... 57 Quick menu .........................................................59 Customer Support - Picture Test / Sound Test ...........................60 - Product/Service Info. ...................................... 61 Simple Manual ....................................................62 Channel Setup - Auto Scan (Auto Tuning)..............................63 - Add/Delete Channel (Manual Tuning) .....64 - Channel Editing ...............................................65 Favorite Channel Setup ....................................66 Favorite Channel List ........................................66 Channel List ........................................................ 67 Channel Information .........................................68 Channel Brief Information ............................... 69 Input List .............................................................. 70 Input Label............................................................ 71 Reset to factory default (Initial Setting) ...... 72 Mode Setting ...................................................... 73 Demo Mode ........................................................ 74 AV Mode ............................................................... 75 SIMPLINK............................................................. 76 MY MEDIA Connection Method .......................................... 78 Entry Mode .......................................................... 79 Movie List ............................................................ 80 Photo List ............................................................. 87 Music List .............................................................93 DivX Registration Code ....................................98 Deactivation .........................................................99 PICTURE CONTROL Picture Size (Aspect Ratio) Control............100 Picture Wizard ................................................... 102 á°Energy Saving ............................................ 104 Preset Picture Settings (Picture mode)..... 105 Manual Picture Adjustment - User Mode 106 Picture Improvement Technology (Advanced Control) ................................................................107 Expert Picture Control ....................................108 Picture Reset ........................................................111 Power Indicator ....................................................111 TruMotion ............................................................ 112 SOUND & LANGUAGE CONTROL Auto Volume....................................................... 113 Clear Voice II ...................................................... 114 Balance ................................................................ 115 Preset Sound Settings (Sound Mode) ....... 116 Sound Setting Adjustment - User Mode ...117 Audio Reset ........................................................ 118 TV Speakers On/Off Setup ........................... 119 Stereo/SAP Broadcast Setup ...................... 120 Audio Language .............................................. 121 On-screen Menus Language Selection .... 122 Caption Mode - Analog Broadcasting System Captions . 123 - Digital Broadcasting System Captions ... 124 - Caption Option .............................................. 125 APPENDIX Troubleshooting ................................................ 142 Maintenance ...................................................... 145 Product Specifications ................................... 146 IR Code................................................................ 151 External Control through RS-232C ........... 152 Open Source License ..................................... 158 TIME SETTING Clock Setting - Auto Clock Setup ......................................... 126 - Manual Clock Setup .....................................127 Auto On/Off Time Setting ............................ 128 Sleep Timer Setting ........................................ 129 PARENTAL CONTROL / RATINGS Set Password & Lock System - Setting up Your Password .......................... 130 - Set Password .................................................. 131 - Lock System................................................... 132 Channel Blocking ............................................. 133 Movie & TV Rating .......................................... 134 Downloadable Rating ...................................... 139 External Input Blocking .................................. 140 Key Lock .............................................................. 141 FEATURE OF THIS TV ᯍ Some of these features are not available on all models. High-definition television. Highresolution digital television broadcast and playback system composed of roughly a million or more pixels, 16:9 aspect-ratio screens, and AC3 digital audio. A subset of digital television, HDTV formats include 1080i and 720p resolutions. AV Mode is three preset picture and audio settings. It allows the viewer to quickly switch between common settings. It includes Cinema, Sports, and Game Modes. A unique invisible speaker system tuned by renowned audio expert, Mr. Mark Levinson. Speakers are embedded in strategic spots behind the front cabinet and use minute vibrations to turn the entire front bezel into the speaker system. The result s a clean, polished look, and enhanced audio by increasing the âsweet spotâ, giving a wider and richer sound field. Automatically enhances and amplifies the sound of human voice frequency range to help keep dialogue audible when background noise swells. Unlike other sensors which can only sense brightness of ambient light, LGâs âIntelligent Sensorâ uses 4,096 sensing steps to evaluate its surroundings. Using a sophisticated algorithm, the LG processes picture quality elements including brightness, contrast, color, sharpness and white balance. The result is a picture optimized for itâs surroundings, more pleasing to watch and which can also save up to 50% in power consumption. Manufactured under license from Dolby Laboratories. âDolby âand the double-D symbol are trademarks of Dolby Laboratories. HDMI, the HDMI logo and HighDefinition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC." Displays HDTV programs in full 1920 x 1080p resolution for a more detailed picture. View videos and photos and listen to music on your TV through USB 2.0 (âvideosâ dependent on model). ABOUT DIVX VIDEO: DivXÂŽ is a digital video format created by DivX,Inc. This is an official DivX Certified device that plays DivX video. Visit www.divx.com for more information and software tools to convert your files into DivX video. ABOUT DIVX VIDEO-ON-DEMAND: This DivX CertifiedÂŽ device must be registered in order to play DivX Videoon-Demand (VOD) content. To generate the registration code, locate the DivX VOD section in the device setup menu. Go to vod.divx.com with this code to complete the registration process and learn more about DivX VOD. âDivX Certified to play DivX video up to HD 1080p, including premium contentâ âPat. 7,295,673; 7,460,688;7,519,274â IMPORTANT INFORMATION TO PREVENT âIMAGE BURN / BURN-INâ ON YOUR TV SCREEN ᯍ ᯍ ᯍ When a fixed image (e.g. logos, screen menus, video game, and computer display) is displayed on the TV for an extended period, it can become permanently imprinted on the screen. This phenomenon is known as âimage burnâ or âburn-in.â Image burn is not covered under the manufacturerâs warranty. In order to prevent image burn, avoid displaying a fixed image on your TV screen for a prolonged period (2 or more hours for LCD, 1 or more hours for Plasma). Image burn can also occur on the letterboxed areas of your TV if you use the 4:3 aspect ratio setting for an extended period. PREPARATION ACCESSORIES Ensure that the following accessories are included with your TV. If an accessory is missing, please contact the dealer where you purchased the TV. The accessories included may differ from the images below. PREPARATION 1.5V 1.5V Ownerâs Manual CD Manual Remote Control, Batteries (AAA) Option Extras Not included with all models When using the VGA (D-sub 15 pin cable) PC connection, the user must use shielded signal interface cables with ferrite cores to maintain standards compliance. * Wipe spots on the exterior only with the polishing cloth. Polishing Cloth * Do not wipe roughly when removing stains. Excessive pressure may cause scratches or discoloration. D-sub 15 pin Cable 19/22/26LE5300, 22/26LE5500 (For 26LE5300, 26LE5500) x4 (For 26LE5300, 26LE5500) x4 (M4 x 14) (M4 x 20) Screws for stand assembly (Refer to P.20, 22) x4 Cable Holder (Refer to p.31) Ring spacers (Refer to p.29) AC/DC Adapter Power Cord 32/37/42/47LD450, 32/37/42/47LD450C, 42/47/55LD630 (For 32/37/42LD450, 32/37/42LD450C, 42LD630) x8 (M4 x 20) Screws for stand assembly (Refer to P.24) Screw for stand fixing (Refer to P.33) Protection Cover (Refer to P.25) Power Cord Protective Bracket and Screw for Power Cord (Refer to P.30) PREPARATION 32/42/47LD420, 32/42/47/55LD520 (Except 55LD520) (Except 47LD420, 47/55LD520) PREPARATION x4 (M4 x 24) Screws for stand assembly (Refer to P.26) Screw for stand fixing (Refer to P.33) Protection Cover (Refer to P.27) Power Cord 32/37/42/47/55LE5300, 42/47/55LE7300 (32/37/42/47/55LE5300) (32LE5300) (37/42LE5300) x4 x4 (M4 x 22) (M4 x 24) (47/55LE5300) x4 (M4 x 26) x4 (M4 x 16) Screws for stand assembly (Refer to P.22) (42/47LE7300) x3 (55LE7300) x4 (M4 x 20) (M4 x 12) x3 x4 (M4 x 26) (M4 x 16) Screws for stand assembly (Refer to P.21) (For 42/47/55LE7300) (For 32LE5300) x2 Cable Holder (Refer to p.31) 10 Component gender cable, AV gender cable Cable Management Clip (Refer to p.31) Screw for stand fixing (Refer to P.33) FRONT PANEL INFORMATION ᯍ Image shown may differ from your TV. 19/22LE5300, 22LE5500 Remote Control Sensor PREPARATION 19/22/26/32/37/42/47/55LE5300, 22/26LE5500 Power/Standby Indicator (Can be adjusted using the Power Indicator in the OPTION menu.p.111) 26/32/37/42/47/55LE5300, 26LE5500 SPEAKER Remote Control Sensor Intelligent Sensor Adjusts picture according to the surrounding conditions Power/Standby Indicator (Can be adjusted using the Power Indicator in the OPTION menu.p.111) 19/22/26LE5300, 22/26LE5500 CH VOL ENTER CHANNEL VOLUME (-, +) (á°,á°) Buttons Buttons MENU INPUT ENTER MENU INPUT POWER Button Button Button Button 32/37/42/47/55LE5300 CH VOL CHANNEL VOLUME (-, +) (á°,á°) Buttons Buttons ENTER MENU INPUT ENTER MENU INPUT POWER Button Button Button Button 11 32/37/42/47/55LE5300 PREPARATION USB IN 10 OPTICAL DIGITAL AUDIO OUT (CONTROL & SERVICE) RS-232C IN AV IN 1 RGB IN (PC) COMPONENT IN 1 ANTENNA/ CABLE IN AUDIO IN (DVI) PB PR VIDEO (RGB/DVI) VIDEO L/MONO AUDIO R AUDIO AV IN2 VIDEO / AUDIO /DVI IN H/P COMPONENT IN2 Y PB PR / AUDIO IN 4 CAUTION For HDMI IN 4 and USB IN For an optimal connection, HDMI cables and USB devices should have bezels less than 10 mm (0.39 inches) thick. 42/47/55LE7300 RS-232C IN (CONTROL & SERVICE) OPTICAL DIGITAL AUDIO OUT /DVI IN AV IN 1 RGB IN (PC) L/MONO AUDIO R VIDEO 1(DVI) AUDIO IN (RGB/DVI) PB VIDEO PR AUDIO ANTENNA/ CABLE IN *A 10 mm (0.39 inches) COMPONENT IN 1 17 PREPARATION STAND INSTRUCTIONS (For 26/32/37/42/47/55LE5300, 26LE5500) ᯍ Image shown may differ from your TV. PREPARATION INSTALLATION Carefully place the TV screen side down on a cushioned surface to protect the screen from damage. Assemble the parts of the STAND BODY with the STAND BASE of the TV. M4 x 20 M4 x 22 32LE5300 26LE5300, 26LE5500 Assemble the TV as shown. STAND BODY M4 x 24 M4 x 26 37/42LE5300 Assemble the part of the STAND REAR COVER with the TV. STAND BASE 47/55LE5300 STAND REAR COVER Install the 4 screws into the holes shown. ! NOTE When assembling the desk type stand, make sure the screws are fully tightened (If not tightened fully, the TV can tilt forward after the product installation). Do not over tighten. 22 M4 x 14 26LE5300, 26LE5500 M4 x 16 Other models 1 Carefully place the TV screen side down on a cushioned surface to protect the screen from damage. Remove the screws from the TV. Detach the STAND REAR COVER from TV. Detach the stand from TV. PREPARATION DETACHMENT 23 PREPARATION VESA WALL MOUNTING PREPARATION Install your wall mount on a solid wall perpendicular to the floor. When attaching to other building materials, please contact your nearest installer. If installed on a ceiling or slanted wall, it may fall and result in severe personal injury. We recommend that you use an LG brand wall mount when mounting the TV to a wall. LG recommends that wall mounting be performed by a qualified professional installer. VESA (A * B) Model 19LE5300, 22LE5300, 22LE5500, 26LE5300, 26LE5500 32LE5300, 32LD420, 32LD450, 32LD450C, 32LD520 37LE5300, 42LE5300, 47LE5300, 37LD450, 37LD450C 42LE7300, 47LE7300 42LD450, 42LD450C, 47LD450, 47LD450C, 42LD420, 47LD420, 42LD520, 47LD520, 42LD630, 47LD630 Standard Screw Quantity Wall Mounting Bracket (sold separately) LSW100B, LSW100BG 100 * 100 M4 LSW100B, LSW100BG 200 * 100 M4 LSW200B, LSW200BG 200 * 200 M6 LSW400B, LSW400BG 55LE5300, 55LE7300, 55LD520, 55LD630 28 400 * 400 M6 ! NOTE Do not use screws that do not comply with the VESA standard screw specifications. Do not use fasten the screws too strongly, this may damage the TV or cause the TV to a fall, leading to personal injury. LG is not liable for these kinds of accidents. LG is not liable for TV damage or personal injury when a non-VESA or non specified wall mount is used or the consumer fails to follow the TV installation instructions. PREPARATION Screw length needed depends on the wall mount used. For further information, refer to the instructions included with the mount. Standard dimensions for wall mount kits are shown in the table. When purchasing our wall mount kit, a detailed installation manual and all parts necessary for assembly are provided. Do not use screws longer than the standard dimension, as they may cause damage to the inside to the TV. For wall mounts that do not comply with the VESA standard screw specifications, the length of the screws may differ depending on their specifications. CAUTION Do not install your wall mount kit while your TV is turned on. It may result in personal injury due to electric shock. For 26LE5300, 26LE5500 Place the ring spacers on the set before installing the wall mounting bracket so that the inclination of the backside of the set can be adjusted perpendicularly. 4-RING SPACERS 29 19/22/26LE5300, 22/26LE5500 After connecting the cables as necessary, install the CABLE HOLDER as shown and bundle the cables. FOR DESK-TYPE STAND Install the CABLE MANAGEMENT CLIP as shown. PREPARATION 42/47/55LE7300 CABLE HOLDER CABLE MANAGEMENT CLIP 32/37/42/47/55LE5300 Secure the power cord with the CABLE HOLDER on the TV back cover. It will help prevent the power cable from being removed by accident. Connect the cables as necessary. To connect additional equipment, see the EXTERNAL EQUIPMENT SETUP section. FOR WALL MOUNT CABLE HOLDER After connecting the cables as necessary, install the CABLE HOLDER as shown and bundle the cables. Connect the cables as necessary. To connect additional equipment, see the EXTERNAL EQUIPMENT SETUP section. Install CABLE HOLDER as shown and bundle the cables. CABLE HOLDER CABLE HOLDER 31 PREPARATION DESKTOP PEDESTAL INSTALLATION ᯍ Image shown may differ from your TV. For proper ventilation, allow a clearance of 10.1 cm (4 inch) on all four sides from the wall. PREPARATION 10.1 cm (4 inch) 10.1 cm (4 inch) 10.1 cm (4 inch) 10.1 cm (4 inch) CAUTION Ensure adequate ventilation by following the clearance recommendations. Do not mount near or above any type of heat source. SWIVEL STAND (Except 19/22LE5300, 22LE5500) After installing the TV, you can adjust the TV set manually to the left or right direction by 20 Âş to suit your viewing position. KENSINGTON SECURITY SYSTEM ᯍ This feature is not available for all models. - The TV is equipped with a Kensington Security System connector on the back panel. Connect the Kensington Security System cable as shown below. - For the detailed installation and use of the Kensington Security System, refer to the userâs guide provided with the Kensington Security System. For further information, contact http://www.kensington.com, the internet homepage of the Kensington company. Kensington sells security systems for expensive electronic equipment such as notebook PCs and LCD projectors. NOTE: The Kensington Security System is an optional accessory. 32 ATTACHING THE TV TO A DESK (For 32/42LD420, 32/37/42LD450, 32/37/42LD450C, 32/42LD520, 42LD630, 32LE5300) Image shown may differ from your TV. The TV must be attached to a desk so it cannot be pulled in a forward/backward direction, potentially causing injury or damaging the product. Stand PREPARATION ᯍ 1-Screw (provided as parts of the product) Desk For 32/37/42/47LD450C Stand Desk 4-Screws (not provided as parts of the product) Recommended screw size: M5 x L (*L: Table depth + 8~10 mm) ex) Table depth: 15mm, Screw: M5 x 25 WARNING To prevent TV from falling over, the TV should be securely attached to the floor/wall per installation instructions. Tipping, shaking, or rocking the machine may cause injury. 33 PREPARATION SECURING THE TV TO THE WALL TO PREVENT FALLING WHEN THE TV IS USED ON A STAND ᯍ PREPARATION ᯍ You should purchase necessary components to prevent the TV from tipping over (when not using a wall mount). Image shown may differ from your TV. We recommend that you set up the TV close to a wall so it cannot fall over if pushed backwards. Additionally, we recommend that the TV be attached to a wall so it cannot be pulled in a forward direction, potentially causing injury or damaging the product. Caution: Please make sure that children donât climb on or hang from the TV. ᯍ Insert the eye-bolts (or TV brackets and bolts) to tighten the product to the wall as shown in the picture. * If your product has the bolts in the eye-bolts position before inserting the eye-bolts, loosen the bolts. * Insert the eye-bolts or TV brackets/bolts and tighten them securely in the upper holes. Secure the wall brackets with the bolts (sold separately) to the wall. Match the height of the bracket that is mounted on the wall to the holes in the product. Ensure the eye-bolts or brackets are tightened securely. ᯍ Use a sturdy rope (sold separately) to tie the product. It is safer to tie the rope so it becomes horizontal between the wall and the product. ! NOTE Use a platform or cabinet strong enough and large enough to support the size and weight of the TV. To use the TV safely make sure that the height of the bracket on the wall and the one on the TV are the same. 34 ᯍ ᯍ To prevent damage do not connect to the power outlet until all connections are made between the devices. Image shown may differ from your TV. ANTENNA OR CABLE CONNECTION PREPARATION 1. Antenna (Analog or Digital) Wall Antenna Socket or Outdoor Antenna without a Cable Box Connections. For optimum picture quality, adjust antenna direction if needed. Wall Antenna Socket Outdoor Antenna (VHF, UHF) Multi-family Dwellings/Apartments (Connect to wall antenna socket) ANTENNA/ CABLE IN RF Coaxial Wire (75 Ί) Single-family Dwellings /Houses (Connect to wall jack for outdoor antenna) Copper Wire Be careful not to bend the copper wire when connecting the antenna. 2. Cable ANTENNA/ CABLE IN Cable TV Wall Jack RF Coaxial Wire (75 Ί) ᯍ ᯍ If the antenna needs to be split for two TVâs, install a 2-Way Signal Splitter. For much more information about antennas visit our Knowledgebase at http://lgknowledgebase. com. Search for antenna. 35 EXTERNAL EXTERNALEQUIPMENT EQUIPMENT SETUP SETUP ᯍ To prevent the equipment damage, never plug in any power cords until you have finished connecting all equipment. ᯍ IThis part of EXTERNAL EQUIPMENT SETUP mainly use picture of for 26LE5300/26LE5500. HD RECEIVER SETUP This TV can receive digital over-the-air/digital cable signals without an external digital set-top box. However, if you do receive digital signals from a digital set-top box or other digital external device. Component Connection EXTERNAL EQUIPMENT SETUP 1. How to connect Connect the video outputs (Y, PB, PR) of the digital set-top box to the COMPONENT IN VIDEO or 1/2* jacks on the TV. Match the jack colors (Y = green, PB = blue, and PR = red). Connect the audio output of the digital set-top box to the COMPONENT IN AUDIO or 1/2* jacks on the TV. VI) PR RS-232C IN (CONTROL&SERVICE) OPTICAL AUDIO IN DIGITAL RGB/DVI AUDIO OUT Turn on the digital set-top box. (Refer to the ownerâs manual for the digital settop box operation.) 2. How to use ᯍ PB AV IN VIDEO L(MONO) AUDIO R GB IN (PC) PB VIDEO PR AUDIO COMPONENT IN ANTENNA/ CABLE IN Select the Component or Component1/2* input source on the TV using the INPUT button on the remote control. * Component2: For 32/37/42/47/55LE5300, 42/47/55LE7300 ᯍ Y, CB/PB, CR/PR 1280x720p 1920x1080i 1920x1080p 36 60.00 31.47 59.94 31.50 60.00 44.96 59.94 45.00 60.00 33.72 59.94 33.75 60.00 26.97 23.976 27.00 24.00 33.71 29.97 33.75 30.00 67.432 59.94 67.50 60.00 USB IN 15.73 IN 4 59.94 AV IN2 VIDEO / AUDIO 720x480p 15.73 For 32/37/42/47/55LE5300, 42/47/55LE7300 H/P 720x480i Vertical Frequency(Hz) COMPONENT IN2 Y PB PR / AUDIO Resolution Horizontal Frequency(KHz) PR PB HDMI Connection DC-IN No separate audio connection is necessary. HDMI supports both audio and video. (DVI) RS-232C IN (CONTROL&SERVICE) OPTICAL AUDIO IN DIGITAL RGB/DVI AUDIO OUT RGB IN (PC) ᯍ PB VIDEO PR AUDIO COMPONENT IN 2. How to use ᯍ AV IN VIDEO L(MONO) AUDIO R Turn on the digital set-top box. (Refer to the ownerâs manual for the digital settop box.) Select the HDMI1, HDMI2, HDMI3*, or HDMI4** input source on the TV using the INPUT button on the remote control. * HDMI3: For 26LE5300/5500, 32/42/47/55LD520, 42/47/55LD630 ** HDMI4: For 32/37/42/47/55LE5300, 42/47/55LE7300 HDMI OUTPUT EXTERNAL EQUIPMENT SETUP Connect the digital set-top box to HDMI/DVI IN 1, 2, 3*, or 4** jack on the TV. /DVI IN 1. How to connect ! NOTE If an HDMI cable doesnât support High Speed HDMI, it can cause flickers or no screen display. In this case use the latest cables that support High Speed HDMI. HDMI Audio Supported Format: Dolby Digital (32 KHz, 44.1 KHz, 48 KHz), Linear PCM (32 KHz, 44.1 KHz, 48 KHz) HDMI-DTV Resolution 720x480p 1280x720p 1920x1080i 1920x1080p Horizontal Frequency(KHz) Vertical Frequency(Hz) 31.47 59.94 31.50 60.00 44.96 59.94 45.00 60.00 33.72 59.94 33.75 60.00 26.97 23.976 27.00 24.00 33.71 29.97 33.75 30.00 67.432 59.94 67.50 60.00 37 EXTERNAL EQUIPMENT SETUP 1. How to connect DC-IN EXTERNAL EQUIPMENT SETUP /DVI IN DVI to HDMI Connection (DVI) RS-232C IN (CONTROL&SERVICE) Connect the DVI output of the digital set-top box to the HDMI/DVI IN 1 or 2* jack on the TV. Connect the digital set-top box audio output to the AUDIO IN (RGB/DVI) jack on the TV. OPTICAL AUDIO IN DIGITAL RGB/DVI AUDIO OUT AV IN VIDEO1 L(MONO) AUDIO R RGB IN (PC) PB VIDEO PR AUDIO COMPONENT IN 2. How to use ᯍ ᯍ Turn on the digital set-top box. (Refer to the ownerâs manual for the digital settop box.) Select the HDMI1 or HDMI2* input source on the TV using the INPUT button on the remote control. * HDMI2: For 32/42/47/55LD520, 42/47/55LD630 AUDIO ! NOTE A DVI to HDMI cable or adapter is required for this connection. DVI doesn't support audio, so a separate audio connection is necessary. 38 DVI OUTPUT DVD SETUP Component Connection 1. How to connect Connect the audio outputs of the DVD to the COMPONENT IN AUDIO or 1/2* jacks on the TV. (DVI) PB PR RS-232C IN ᯍ ᯍ OPTICAL AUDIO IN DIGITAL RGB/DVI AUDIO OUT Turn on the DVD player, insert a DVD. Select the Component or Component1/2* input source on the TV using the INPUT button on the remote control. Refer to the DVD playerâs manual for operating instructions. (CONTROL&SERVICE) 2. How to use ᯍ EXTERNAL EQUIPMENT SETUP Connect the video outputs (Y, PB, PR) of the DVD to the COMPONENT IN VIDEO or 1/2* jacks on the TV. Match the jack colors (Y = green, PB = blue, and PR = red). AV IN VIDEO L(MONO) AUDIO R RGB IN (PC) PB VIDEO PR AUDIO ANTENNA/ CABLE IN COMPONENT IN * Component2: For 32/37/42/47/55LE5300, 42/47/55LE7300 Component Input ports To get better picture quality, connect a DVD player to the component input ports as shown below. PB PR B-Y R-Y Cb Cr Pb Pr USB IN PR H/P IN 4 PB AV IN2 VIDEO / AUDIO Video output ports on DVD player COMPONENT IN2 Y PB PR / AUDIO Component ports on the TV For 32/37/42/47/55LE5300, 42/47/55LE7300 PR PB 39 EXTERNAL EQUIPMENT SETUP Composite (RCA) Connection 1. How to connect DVI) EXTERNAL EQUIPMENT SETUP ᯍ ᯍ RS-232C IN (CONTROL&SERVICE) Connect the AUDIO/VIDEO jacks between TV and DVD. Match the jack colors (Video = yellow, Audio Left = white, and Audio Right = red) 2. How to use ᯍ OPTICAL AUDIO IN DIGITAL RGB/DVI AUDIO OUT AV IN VIDEO L(MONO) AUDIO R GB IN (PC) Turn on the DVD player, insert a DVD. Select the AV or AV1/2* input source on the TV using the INPUT button on the remote control. Refer to the DVD player's manual for operating instructions. PB VIDEO PR AUDIO ANTENNA/ CABLE IN COMPONENT IN * AV2: Except 19/22/26LE5300, 22/26LE5500 VIDEO AUDIO HDMI Connection Connect the HDMI output of the DVD to the HDMI/DVI IN 1, 2, 3*, or 4** jack on the TV. DC-IN /DVI IN 1. How to connect (DVI) No separate audio connection is necessary. HDMI supports both audio and video. RS-232C IN (CONTROL&SERVICE) OPTICAL AUDIO IN DIGITAL RGB/DVI AUDIO OUT AV IN VIDEO L(MONO) AUDIO R RGB IN (PC) 2. How to use ᯍ ᯍ PB VIDEO PR ! NOTE If an HDMI cable doesnât support High Speed HDMI, it can cause flickers or no screen display. In this case use the latest cables that support High Speed HDMI. HDMI Audio Supported Format: Dolby Digital (32 KHz, 44.1 KHz, 48 KHz), Linear PCM (32 KHz, 44.1 KHz, 48 KHz) AUDIO COMPONENT IN Select the HDMI1, HDMI2, HDMI3*, or HDMI4** input source on the TV using the INPUT button on the remote control. Refer to the DVD player's manual for operating instructions. * HDMI3: For 26LE5300/5500, 32/42/47/55LD520, 42/47/55LD630 ** HDMI4: For 32/37/42/47/55LE5300, 42/47/55LE7300 40 HDMI OUTPUT VCR SETUP Antenna Connection 1. How to connect O) AUDIO R Connect the RF antenna out socket of the VCR to the ANTENNA/CABLE IN socket on the TV. AUDIO ANTENNA/ CABLE IN Connect the antenna cable to the RF antenna in socket of the VCR. ANT OUT S-VIDEO ANT IN OUTPUT SWITCH VIDEO AUDIO Wall Jack 2. How to use ᯍ ᯍ Set VCR output switch to 3 or 4 and then tune TV to the same channel number. Insert a video tape into the VCR and press PLAY on the VCR (Refer to the VCR ownerâs manual). Antenna EXTERNAL EQUIPMENT SETUP Composite (RCA) Connection 1. How to connect Connect the AUDIO/VIDEO jacks between TV and VCR. Match the jack colors (Video = yellow, Audio Left = white, and Audio Right = red) VI) 2. How to use ᯍ ᯍ Insert a video tape into the VCR and press PLAY on the VCR. (Refer to the VCR ownerâs manual.) Select the AV or AV1/2* input source on the TV using the INPUT button on the remote control. RS-232C IN (CONTROL&SERVICE) OPTICAL AUDIO IN DIGITAL RGB/DVI AUDIO OUT AV IN VIDEO L(MONO) AUDIO R B IN (PC) PB VIDEO PR AUDIO COMPONENT IN ANTENNA/ CABLE IN * AV2: Except 19/22/26LE5300, 22/26LE5500 ! NOTE If you have a mono VCR, connect the audio cable from the VCR to the AUDIO L(MONO) jack of the TV. ANT IN S-VIDEO ANT OUT OUTPUT SWITCH VIDEO AUDIO 41 EXTERNAL EQUIPMENT SETUP OTHER A/V SOURCE SETUP EXTERNAL EQUIPMENT SETUP Connect the AUDIO/VIDEO jacks between TV and external equipment. Match the jack colors. (Video = yellow, Audio Left = white, and Audio Right = red) DC-IN /DVI IN 1. How to connect (DVI) RS-232C IN (CONTROL&SERVICE) OPTICAL AUDIO IN DIGITAL RGB/DVI AUDIO OUT AV IN VIDEO L(MONO) AUDIO R RGB IN (PC) 2. How to use PB VIDEO PR AUDIO COMPONENT IN ᯍ ᯍ Select the AV or AV1/2* input source on the TV using the INPUT button on the remote control. Operate the corresponding external equipment. ANTENNA/ CABLE IN * AV2: Except 19/22/26LE5300, 22/26LE5500 VIDEO Video Game Set Camcorder 42 USB CONNECTION 1. How to connect 2. How to use After connecting the USB IN jack, you Memory Key IN 3 ᯍ or H/P use the USB function. (p.78) EXTERNAL EQUIPMENT SETUP Connect the USB device to the USB IN jack on the side of TV. USB IN HEADPHONE SETUP You can listen to the sound through the headphone. Plug the headphone into the headphone socket. To adjust the headphone volume, press the VOL +/- button. If you press the MUTE button, the sound from the headphone is switched off. H/P 1. How to connect ! NOTE AUDIO menu options are disabled when connecting a headphone. When changing AV MODE with a headphone connected, the change is applied to video but not to audio. Optical Digital Audio Out is not available when connecting a headphone. 43 EXTERNAL EQUIPMENT SETUP AUDIO OUT CONNECTION 1. How to connect EXTERNAL EQUIPMENT SETUP (DVI) Connect one end of the optical cable to the TV port of OPTICAL DIGITAL AUDIO OUT. RS-232C IN (CONTROL&SERVICE) OPTICAL AUDIO IN DIGITAL RGB/DVI AUDIO OUT AV IN VIDEO L(MONO) AUDIO R Connect the other end of the optical cable to the digital audio input on the audio equipment. Set the âTV Speaker option - Offâ in the AUDIO menu. (p.119). See the external audio equipment instruction manual for operation. ! NOTE When connecting with external audio equipment, such as amplifiers or speakers, you can turn the TV speakers off in the menu. (p.119) CAUTION Do not look into the optical output port. Looking at the laser beam may damage your vision. Audio with ACP (Audio Copy Protection) function may block digital audio output. 44 /DVI IN Send the TVâs audio to external audio equipment via the Audio Output port. If you want to enjoy digital broadcasting through 5.1-channel speakers, connect the OPTICAL DIGITAL AUDIO OUT terminal on the back of TV to a Home Theater (or amp). RGB IN (PC) PB PR VIDEO AUDIO COMPONENT IN ANTENNA/ CABLE IN PC SETUP VGA (D-Sub 15 Pin) Connection DC-IN /DV This TV provides Plug and Play capability, meaning that a PC adjusts automatically to the TVâs settings. RS 232C IN (DVI) (CONTROL&SERVICE) Connect the VGA output of the PC to the RGB IN (PC) jack on the TV. RGB IN (PC) ᯍ PB VIDEO PR AUDIO COMPONENT IN Connect PC audio output to the AUDIO IN (RGB/DVI) jack on the TV. 2. How to use ᯍ AV IN VIDEO L(MONO) AUDIO R RGB OUTPUT AUDIO Turn on the PC and the TV. Select the RGB-PC input source on the TV using the INPUT button on the remote control. EXTERNAL EQUIPMENT SETUP OPTICAL AUDIO IN DIGITAL RGB/DVI AUDIO OUT 1. How to connect 45 EXTERNAL EQUIPMENT SETUP DVI to HDMI Connection 1. How to connect Connect the DVI output of the PC to the HDMI/DVI IN 1 or 2* jack on the TV. Connect the PC audio output to the AUDIO IN (RGB/DVI) jack on the TV. 2. How to use ᯍ ᯍ Turn on the PC and the TV. Select the HDMI1 or HDMI2* input source on the TV using the INPUT button on the remote control. DC-IN /DVI IN EXTERNAL EQUIPMENT SETUP (DVI) RS-232C IN (CONTROL&SERVICE) OPTICAL AUDIO IN DIGITAL RGB/DVI AUDIO OUT RGB IN (PC) PB VIDEO PR AUDIO COMPONENT IN * HDMI2: For 32/42/47/55LD520, 42/47/55LD630 AUDIO 46 AV IN VIDEO L(MONO) AUDIO R DVI OUTPUT ! NOTE To get the the best picture quality, adjust the PC graphics card to 1360 x 768 (19/22/26LE5300) or 1920 x 1080 (Other models). In PC mode, there may be noise associated with the resolution, vertical pattern, contrast or brightness. If noise is present, change the PC output to another resolution, change the refresh rate to another rate or adjust the brightness and contrast on the PICTURE menu until the picture is clear. Avoid keeping a fixed image on the screen for a long period of time. The fixed image may become permanently imprinted on the screen. The synchronization input form for Horizontal and Vertical frequencies is separate. Depending on the graphics card, some resolution settings may not allow the image to be positioned on the screen properly. When selecting HDMI-PC, set the âInput Label - PCâ in the OPTION menu. EXTERNAL EQUIPMENT SETUP Depending on the graphics card, DOS mode may not work if a HDMI to DVI Cable is in use. Supported Display Specifications (RGB-PC, HDMI-PC) Resolution Horizontal Frequency(KHz) Vertical Frequency(Hz) 640x350 31.468 70.09 720x400 31.469 70.08 640x480 31.469 59.94 800x600 37.879 60.31 1024x768 48.363 60.00 1280x768 47.776 59.87 1360x768 47.712 60.015 1280x1024 63.981 60.02 1600x1200 75.00 60.00 1920x1080 RGB-PC 66.587 59.934 1920x1080 HDMI-PC 67.50 60.00 Except 19/22/26LE5300 Except 32/37/42/47/55LE5300, 42/47/55LE7300, 22/26LE5500 47 EXTERNAL EQUIPMENT SETUP Screen Setup for PC mode Selecting Resolution EXTERNAL EQUIPMENT SETUP You can choose the resolution in RGB-PC mode. The Position, Phase, and Size can also be adjusted. You can choose this option only when the PC resolution is set to 1024X768, 1280X768 or 1360X768. 3,&785( áŻ0RYHáŻ(QWHU 6&5((1 5HVROXWLRQ Ř%U %ULJKW %U LJKW K QHVV HVV Ř6KDUSQHVV Ř&RORU Ř7LQW Ř&RORU7HPS Ř$GYDQFHG&RQWURO Ř3LFWXUH5HVHW $XWR&RQILJ Ř 6FUHHQ 5*%3& 3RVLWLRQ 6L]H ᯰ ᯠ3KDVH 5HVHW 48 MENU Select PICTURE. ENTER Select Screen (RGB-PC). ENTER Select Resolution. ENTER Select the desired resolution. ENTER áŻ0RYHá°3UHY ᯥ[ Űł[ Űł[ Auto Configure Automatically adjusts picture position and minimizes image instability. After adjustment, if the image is still not correct, try using the manual settings or a different resolution or refresh rate on the PC. áŻ0RYHá°3UHY áŻ0RYHáŻ(QWHU 5HVROXWLRQ Ř%U %U % LJKW %UL LJKWQH QHVV QHVV Ř6KDUSQHVV Ř&RORU Ř7LQW Ř&RORU7HPS Ř$GYDQFHG&RQWURO Ř3LFWXUH5HVHW $XWR&RQILJ Ř 6FUHHQ 5*%3& 3RVLWLRQ 6L]H $XWR&RQILJ+RPH8VH@ZKHQVHWWLQJ79XS LQKRPH This program is free software; you can redistribute it and/ or modify it under the terms of the GNU General Public License as published by the Free Software Foundation; either version 2 of the license, or (at your option) any later version. This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details. You should have received a copy of the GNU General Public License along with this program; if not, write to the Free Software Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA. If the program is interactive, make it output a short notice like this when it starts in an interactive mode: Gnomovision version 69, Copyright (C) year name of author Gnomovision comes with ABSOLUTELY NO WARRANTY; for details type âshow wâ. This is free software, and you are welcome to redistribute it under certain conditions; type âshow câ for details. The hypothetical commands âshow wâ and âshow câ should show the appropriate parts of the General Public License. Of course, the commands you use may be called something other than âshow wâ and âshow câ; they could even be mouse-clicks or menu items-whatever suits your program. You should also get your employer (if you work as a programmer) or your school, if any, to sign a âcopyright disclaimerâ for the program, if necessary. Here is a sample; alter the names: Yoyodyne, Inc., hereby disclaims all copyright interest in the program âGnomovisionâ (which makes passes at compilers) written by James Hacker. signature of Ty Coon, 1 April 1989 Ty Coon, President of Vice APPENDIX This General Public License does not permit incorporating your program into proprietary programs. If your program is a subroutine library, you may consider it more useful to permit linking proprietary applications with the library. If this is what you want to do, use the GNU Lesser General Public License instead of this license. 161 APPENDIX GNU LESSER GENERAL PUBLIC LICENSE Version 2.1, February 1999 Copyright (C) 1991, 1999 Free Software Foundation, Inc. 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed. [This is the first released version of the Lesser GPL. It also counts as the successor of the GNU Library Public License, version 2, hence the version number 2.1.] Preamble The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General Public Licenses are intended to guarantee your freedom to share and change free software - to make sure the software is free for all its users. This license, the Lesser General Public License, applies to some specially designated software packages - typically libraries - of the Free Software Foundation and other authors who decide to use it. You can use it too, but we suggest you first think carefully about whether this license or the ordinary General Public License is the better strategy to use in any particular case, based on the explanations below. APPENDIX When we speak of free software, we are referring to freedom of use, not price. Our General Public Licenses are designed to make sure that you have the freedom to distribute copies of free software (and charge for this service if you wish); that you receive source code or can get it if you want it; that you can change the software and use pieces of it in new free programs; and that you are informed that you can do these things. To protect your rights, we need to make restrictions that forbid distributors to deny you these rights or to ask you to surrender these rights. These restrictions translate to certain responsibilities for you if you distribute copies of the library or if you modify it. For example, if you distribute copies of the library, whether gratis or for a fee, you must give the recipients all the rights that we gave you. You must make sure that they, too, receive or can get the source code. If you link other code with the library, you must provide complete object files to the recipients, so that they can relink them with the library after making changes to the library and recompiling it. And you must show them these terms so they know their rights. We protect your rights with a two-step method: (1) we copyright the library, and (2) we offer you this license, which gives you legal permission to copy, distribute and/or modify the library. 162 To protect each distributor, we want to make it very clear that there is no warranty for the free library. Also, if the library is modified by someone else and passed on, the recipients should know that what they have is not the original version, so that the original author's reputation will not be affected by problems that might be introduced by others. Finally, software patents pose a constant threat to the existence of any free program. We wish to make sure that a company cannot effectively restrict the users of a free program by obtaining a restrictive license from a patent holder. Therefore, we insist that any patent license obtained for a version of the library must be consistent with the full freedom of use specified in this license. Most GNU software, including some libraries, is covered by the ordinary GNU General Public License. This license, the GNU Lesser General Public License, applies to certain designated libraries, and is quite different from the ordinary General Public License. We use this license for certain libraries in order to permit linking those libraries into nonfree programs. When a program is linked with a library, whether statically or using a shared library, the combination of the two is legally speaking a combined work, a derivative of the original library. The ordinary General Public License therefore permits such linking only if the entire combination fits its criteria of freedom. The Lesser General Public License permits more lax criteria for linking other code with the library. We call this license the "Lesser" General Public License because it does Less to protect the user's freedom than the ordinary General Public License. It also provides other free software developers Less of an advantage over competing non-free programs. These disadvantages are the reason we use the ordinary General Public License for many libraries. However, the Lesser license provides advantages in certain special circumstances. For example, on rare occasions, there may be a special need to encourage the widest possible use of a certain library, so that it becomes a de-facto standard. To achieve this, non-free programs must be allowed to use the library. A more frequent case is that a free library does the same job as widely used non-free libraries. In this case, there is little to gain by limiting the free library to free software only, so we use the Lesser General Public License. In other cases, permission to use a particular library in nonfree programs enables a greater number of people to use a large body of free software. For example, permission to use the GNU C Library in non-free programs enables many more people to use the whole GNU operating system, as well as its variant, the GNU/Linux operating system. Although the Lesser General Public License is Less protective of the users' freedom, it does ensure that the user of a program that is linked with the Library has the freedom and the wherewithal to run that program using a modified version of the Library. The precise terms and conditions for copying, distribution and modification follow. Pay close attention to the difference between a "work based on the library" and a "work that uses the library". The former contains code derived from the library, whereas the latter must be combined with the library in order to run. GNU LESSER GENERAL PUBLIC LICENSE TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION 0. This license agreement applies to any software library or other program which contains a notice placed by the copyright holder or other authorized party saying it may be distributed under the terms of this Lesser General Public License (also called âthis licenseâ). Each license is addressed as "you". A âlibraryâ means a collection of software functions and/or data prepared so as to be conveniently linked with application programs (which use some of those functions and data) to form executables. âSource codeâ for a work means the preferred form of the work for making modifications to it. For a library, complete source code means all the source code for all modules it contains, plus any associated interface definition files, plus the scripts used to control compilation and installation of the library. Activities other than copying, distribution and modification are not covered by this license; they are outside its scope. The act of running a program using the Library is not restricted, and output from such a program is covered only if its contents constitute a work based on the library (independent of the use of the Library in a tool for writing it). Whether that is true depends on what the library does and what the program that uses the library does. 1. You may copy and distribute verbatim copies of the library's complete source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty; keep intact all the You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee. 2. You may modify your copy or copies of the Library or any portion of it, thus forming a work based on the Library, and copy and distribute such modifications or work under the terms of section 1 above, provided that you also meet all of these conditions: a) The modified work must itself be a software library. b) You must cause the files modified to carry prominent notices stating that you changed the files and the date of any change. c) You must cause the whole of the work to be licensed at no charge to all third parties under the terms of this license. d) If a facility in the modified Library refers to a function or a table of data to be supplied by an application program that uses the facility, other than as an argument passed when the facility is invoked, then you must make a good faith effort to ensure that, in the event an application does not supply such function or table, the facility still operates, and performs whatever part of its purpose remains meaningful. (For example, a function in a library to compute square roots has a purpose that is entirely well-defined independent of the application. Therefore, Subsection 2d requires that any application-supplied function or table used by this function must be optional: if the application does not supply it, the square root function must still compute square roots.) These requirements apply to the modified work as a whole. If identifiable sections of that work are not derived from the library, and can be reasonably considered independent and separate works in themselves, then this license, and its terms, do not apply to those sections when you distribute them as separate works. But when you distribute the same sections as part of a whole which is a work based on the library, the distribution of the whole must be on the terms of this license, whose permissions for other licenses extend to the entire whole, and thus to each and every part regardless of who wrote it. Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather, the intent is to exercise the right to control the distribution of derivative or collective works based on the library. APPENDIX The âLibraryâ, below, refers to any such software library or work which has been distributed under these terms. A âwork based on the Libraryâ means either the Library or any derivative work under copyright law: that is to say, a work containing the library or a portion of it, either verbatim or with modifications and/or translated straightforwardly into another language. (Hereinafter, translation is included without limitation in the term âmodificationâ.) notices that refer to this license and to the absence of any warranty; and distribute a copy of this license along with the Library. In addition, mere aggregation of another work not based on the library with the library (or with a work based on the library) on a volume of a storage or distribution medium does not bring the other work under the scope of this license. 163 APPENDIX 3. You may opt to apply the terms of the ordinary GNU General Public License instead of this License to a given copy of the Library. To do this, you must alter all the notices that refer to this License, so that they refer to the ordinary GNU General Public License, version 2, instead of to this License. (If a newer version than version 2 of the ordinary GNU General Public License has appeared, then you can specify that version instead if you wish.) Do not make any other change in these notices. Once this change is made in a given copy, it is irreversible for that copy, so the ordinary GNU General Public License applies to all subsequent copies and derivative works made from that copy. This option is useful when you wish to copy part of the code of the library into a program that is not a library. 4. You may copy and distribute the library (or a portion or derivative of it, under Section 2) in object code or executable form under the terms of Sections 1 and 2 above provided that you accompany it with the complete corresponding machine-readable source code, which must be distributed under the terms of sections 1 and 2 above on a medium customarily used for software interchange. If distribution of object code is made by offering access to copy from a designated place, then offering equivalent access to copy the source code from the same place satisfies the requirement to distribute the source code, even though third parties are not compelled to copy the source along with the object code. 5. A program that contains no derivative of any portion of the Library, but is designed to work with the Library by being compiled or linked with it, is called a âwork that uses the Libraryâ. Such a work, in isolation, is not a derivative work of the Library, and therefore falls outside the scope of this license. APPENDIX However, linking a âwork that uses the libraryâ with the Library creates an executable that is a derivative of the Library (because it contains portions of the library), rather than a âwork that uses the libraryâ. The executable is therefore covered by this license. Section 6 states terms for distribution of such executable. When a âwork that uses the libraryâ uses material from a header file that is part of the library, the object code for the work may be a derivative work of the library even though the source code is not. Whether this is true is especially significant if the work can be linked without the library, or if the work is itself a library. The threshold for this to be true is not precisely defined by law. If such an object file uses only numerical parameters, data structure layouts and accessories, and small macros and small inline functions (ten lines or less in length), then the use of the object file is unrestricted, regardless of whether it is legally a derivative work. (Executable containing this object code plus portions of 164 the library will still fall under Section 6.) Otherwise, if the work is a derivative of the library, you may distribute the object code for the work under the terms of Section 6. Any executable containing that work also fall under Section 6, whether or not they are linked directly with the library itself. 6. As an exception to the sections above, you may also combine or link a "work that uses the library" with the library to produce a work containing portions of the library, and distribute that work under terms of your choice, provided that the terms permit modification of the work for the customer's own use and reverse engineering for debugging such modifications. You must give prominent notice with each copy of the work that the library is used in it and that the Library and its use are covered by this license. You must supply a copy of this license. If the work during execution displays copyright notices, you must include the copyright notice for the library among them, as well as a reference directing the user to the copy of this license. Also, you must do one of these things: a) Accompany the work with the complete corresponding machine-readable source code for the library including whatever changes were used in the work (which must be distributed under Sections 1 and 2 above); and, if the work is an executable linked with the Library, with the complete machine-readable âwork that uses the Libraryâ, as object code and/or source code, so that the user can modify the library and then relink to produce a modified executable containing the modified library. (It is understood that the user who changes the contents of definitions files in the library will not necessarily be able to recompile the application to use the modified definitions.) b) Use a suitable shared library mechanism for linking with the library. A suitable mechanism is one that (1) uses at run time a copy of the library already present on the userâs computer system, rather than copying library functions into the executable, and (2) will operate properly with a modified version of the library, if the user installs one, as long as the modified version is interface-compatible with the version that the work was made with. c) Accompany the work with a written offer, valid for at least three years, to give the same user the materials specified in Subsection 6, above, for a charge no more than the cost of performing this distribution. d) If distribution of the work is made by offering access to copy from a designated place, offer equivalent access to copy the above specified materials from the same place. e) Verify that the user has already received a copy of these materials or that you have already sent this user a copy. For an executable, the required form of the "work that uses the library" must include any data and utility programs needed for reproducing the executable from it. However, as a special exception, the materials to be distributed need not include anything that is normally distributed (in either source or binary form) with the major components (compiler, kernel, and so on) of the operating system on which the executable runs, unless that component itself accompanies the executable. It may happen that this requirement contradicts the license restrictions of other proprietary libraries that do not normally accompany the operating system. Such a contradiction means you cannot use both them and the library together in an executable that you distribute. 7. You may place library facilities that are a work based on the library side-by-side in a single library together with other library facilities not covered by this license, and distribute such a combined library, provided that the separate distribution of the work based on the Library and of the other library facilities is otherwise permitted, and provided that you do these two things: a) Accompany the combined library with a copy of the same work based on the Library, uncombined with any other library facilities. This must be distributed under the terms of the sections above. b) Give prominent notice with the combined library of the fact that part of it is a work based on the library, and explaining where to find the accompanying uncombined form of the same work. 9. You are not required to accept this license, since you have not signed it. However, nothing else grants you permission to modify or distribute the library or its derivative works. These actions are prohibited by law if you do not accept this license. Therefore, by modifying or distributing the library (or any work based on the library), you indicate your acceptance of this license to do so, and all its terms and conditions for copying, distributing or modifying the library or works based on it. 10. Each time you redistribute the library (or any work based on the Library), the recipient automatically receives a license from the original licensor to copy, distribute, link with or modify the library subject to these terms and conditions. You may not impose any further restrictions on the recipients' exercise of the rights granted herein. 11. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to patent issues), conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this license, they do not excuse you from the conditions of this license. If you cannot distribute so as to satisfy simultaneously your obligations under this license and any other pertinent obligations, then as a consequence you may not distribute the library at all. For example, if a patent license would not permit royalty-free redistribution of the library by all those who receive copies directly or indirectly through you, then the only way you could satisfy both it and this license would be to refrain entirely from distribution of the library. If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply, and the section as a whole is intended to apply in other circumstances. It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of any such claims; this section has the sole purpose of protecting the integrity of the free software distribution system which is implemented by public license practices. Many people have made generous contributions to the wide range of software distributed through that system in reliance on consistent application of that system; it is up to the author/donor to decide if he or she is willing to distribute software through any other system and a license cannot impose that choice. This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this license. 12. If the distribution and/or use of the library is restricted in certain countries either by patents or by copyrighted interfaces, the original copyright holder who places the library under this license may add an explicit geographical distribution limitation excluding those countries, so that distribution is permitted only in or among countries not thus excluded. In such case, this license incorporates the limitation as if written in the body of this license. APPENDIX 8. You may not copy, modify, sublicense, link with, or distribute the library except as expressly provided under this license. Any attempt otherwise to copy, modify, sublicense, link with, or distribute the library is void, and will automatically terminate your rights under this license. However, parties who have received copies, or rights, from you under this license will not have their licenses terminated so long as such parties remain in full compliance. You are not responsible for enforcing compliance by third parties with this license. 13. The Free Software Foundation may publish revised and/ or new versions of the Lesser General Public License from time to time. Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems or concerns. Each version is given a distinguishing version number. If the library specifies a version number of this license which applies to it and âany later versionâ, you have the option of following the terms and conditions either of that version or of any later version published by the Free Software Foundation. 165 APPENDIX If the library does not specify a license version number, you may choose any version ever published by the Free Software Foundation. 14. If you wish to incorporate parts of the library into other free programs whose distribution conditions are incompatible with these, write to the author to ask for permission. For software which is copyrighted by the Free Software Foundation, write to the Free Software Foundation; we sometimes make exceptions for this. Our decision will be guided by the two goals of preserving the free status of all derivatives of our free software and of promoting the sharing and reuse of software generally. NO WARRANTY 15. BECAUSE THE LIBRARY IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE LIBRARY, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE LIBRARY "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE LIBRARY IS WITH YOU. SHOULD THE LIBRARY PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION. APPENDIX 16. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE LIBRARY AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE LIBRARY (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE LIBRARY TO OPERATE WITH ANY OTHER SOFTWARE), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. END OF TERMS AND CONDITIONS How to apply these terms to your new libraries If you develop a new library, and you want it to be of the greatest possible use to the public, we recommend making 166 it free software that everyone can redistribute and change. You can do so by permitting redistribution under these terms (or, alternatively, under the terms of the ordinary General Public License). To apply these terms, attach the following notices to the library. It is safest to attach them to the start of each source file to most effectively convey the exclusion of warranty; and each file should have at least the âcopyrightâ line and a pointer to where the full notice is found. one line to give the library's name and a brief idea of what it does. Copyright (C) This library is free software; you can redistribute it and/or modify it under the terms of the GNU Lesser General Public License as published by the Free Software Foundation; either version 2.1 of the license, or (at your option) any later version. This library is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU Lesser General Public License for more details. You should have received a copy of the GNU Lesser General Public License along with this library; if not, write to the Free Software Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA Also add information on how to contact you by electronic and paper mail. You should also get your employer (if you work as a programmer) or your school, if any, to sign a âcopyright disclaimerâ for the library, if necessary. Here is a sample; alter the names: Yoyodyne, Inc., hereby disclaims all copyright interest in the library âFrobâ (a library for tweaking knobs) written by James Random Hacker. signature of Ty Coon, 1 April 1990 Ty Coon, President of Vice MOZILLA PUBLIC LICENSE Version 1.1 --------------which, at the time of its release under this license is not already covered code governed by this license. 1.Definitions. 1.0.1. âCommercial useâ means distribution or otherwise making the covered code available to a third party. 1.1. âContributorâ means each entity that creates or contributes to the creation of modifications. 1.2. âContributor versionâ means the combination of the original code, prior modifications used by a contributor, and the modifications made by that particular contributor. 1.3. âCovered codeâ means the original code or modifications or the combination of the original code and modifications, in each case including portions thereof. 1.4. âElectronic distribution mechanismâ means a mechanism generally accepted in the software development community for the electronic transfer of data. 1.10.1. âPatent claimsâ means any patent claim(s), now owned or hereafter acquired, including without limitation, method, process, and apparatus claims, in any patent licensable by grantor. 1.11. âSource codeâ means the preferred form of the covered code for making modifications to it, including all modules it contains, plus any associated interface definition files, scripts used to control compilation and installation of an executable, or source code differential comparisons against either the original code or another well known, available covered code of the contributor's choice. The source code can be in a compressed or archival form, provided the appropriate decompression or de-archiving software is widely available for no charge. âExecutableâ means covered code in any form other than source code. 1.6. âInitial developerâ means the individual or entity identified as the initial Developer in the Source Code notice required by exhibit A. 1.7. âLarger workâ means a work which combines covered code or portions thereof with code not governed by the terms of this License. 1.8. âLicenseâ means this document. 2. Source Code License. 1.8.1. âLicensableâ means having the right to grant, to the maximum extent possible, whether at the time of the initial grant or subsequently acquired, any and all of the rights conveyed herein. 1.9. âModificationsâ means any addition to or deletion from the substance or structure of either the original code or any previous modifications. When covered code is released as a series of files, a modification is: A. Any addition to or deletion from the contents of a file containing original code or previous modifications. B. Any new file that contains any part of the original code or previous modifications. 2.1. The initial developer grant. The initial developer hereby grants You a world-wide, royalty-free, non-exclusive license, subject to third party intellectual property claims: APPENDIX 1.5. 1.12. âYouâ (or âYourâ) means an individual or a legal entity exercising rights under, and complying with all of the terms of, this license or a future version of this license issued under section 6.1. For legal entities, âYouâ includes any entity which controls, is controlled by, or is under common control with You. For purposes of this definition, âcontrolâ means (a) the power, direct or indirect, to cause the direction or management of such entity, whether by contract or otherwise, or (b) ownership of more than fifty percent (50%) of the outstanding shares or beneficial ownership of such entity. a) under intellectual property rights (other than patent or trademark) licensable by initial developer to use, reproduce, modify, display, perform, sublicense and distribute the original code (or portions thereof) with or without modifications, and/or as part of a larger work; and (b) under patents claims infringed by the making, using or selling of original code, to make, have made, use, practice, sell, and offer for sale, and/ or otherwise dispose of the original code (or portions there of). 1.10. âOriginal codeâ means source code of computer software code which is described in the source code notice required by exhibit as original code, and 167 APPENDIX (c) the licenses granted in this section 2.1(a) and (b) are effective on the date Initial developer first distributes original code under the terms of this license. (d) Notwithstanding section 2.1(b) above, no patent license is granted: 1) for code that You delete from the original Code; 2) separate from the original code; or 3) for infringements caused by: i) the modification of the original code or ii) the combination of the original code with other software or devices. 2.2. Contributor Grant. Subject to third party intellectual property claims, each contributor hereby grants You a world-wide, royalty-free, non-exclusive license APPENDIX (a) under intellectual property rights (other than patent or trademark) licensable by contributor, to use, reproduce, modify, display, perform, sublicense and distribute the modifications created by such contributor (or portions thereof) either on an unmodified basis, with other modifications, as covered code and/or as part of a larger work; and (b) under patent claims infringed by the making, using, or selling of modifications made by that contributor either alone and/or in combination with its contributor version (or portions of such combination), to make, use, sell, offer for sale, have made, and/or otherwise dispose of: 1) modifications made by that contributor (or portions thereof); and 2) the combination of modifications made by that contributor with its contributor version (or portions of such combination). (c) the licenses granted in sections 2.2(a) and 2.2(b) are effective on the date contributor first makes commercial use of the covered code. (d) Notwithstanding section 2.2(b) above, no patent license is granted: 1) for any code that contributor has deleted from the contributor version; 2) separate from the contributor version; 3) for infringements caused by: i) third party modifications of contributor version or ii) the combination of modifications made by that contributor with other software (except as part of the contributor version) or other devices; or 4) under patent claims infringed by covered code in the absence of modifications made by that contributor. 3. Distribution Obligations. 3.1. 168 Application of license. The modifications which You create or to which you contribute are governed by the terms of this license, including without limitation section 2.2. The source code version of covered code may be distributed only under the terms of this license or a future version of this license released under section 6.1, and you must include a copy of this license with every copy of the source code you distribute. You may not offer or impose any terms on any source code version that alters or restricts the applicable version of this license or the recipients' rights hereunder. However, you may include an additional document offering the additional rights described in section 3.5. 3.2. Availability of source code. Any modification which you create or to which you contribute must be made available in source code form under the terms of this license either on the same media as an executable version or via an accepted electronic distribution mechanism to anyone to whom you made an executable version available; and if made available via electronic distribution mechanism, must remain available for at least twelve (12) months after the date it initially became available, or at least six (6) months after a subsequent version of that particular modification has been made available to such recipients. You are responsible for ensuring that the source code version remains available even if the electronic distribution mechanism is maintained by a third party. 3.3. Description of modifications. You must cause all covered code to which you contribute to contain a file documenting the changes You made to create that covered code and the date of any change. You must include a prominent statement that the modification is derived, directly or indirectly, from original code provided by the initial developer and including the name of the initial developer in (a) the source code, and (b) in any notice in an executable version or related documentation in which you describe the origin or ownership of the covered code. 3.4. Intellectual property matters (a) Third party claims. If contributor has knowledge that a license under a third party's intellectual property rights is required to exercise the rights granted by such contributor under sections 2.1 or 2.2, contributor must include a text file with the source code distribution titled "LEGAL" which describes the claim and the party making the claim in sufficient detail that a recipient will know whom to contact. If contributor obtains such knowledge after the modification is made available as described in section 3.2, contributor shall promptly modify the LEGAL file in all copies contributor makes available thereafter and shall take other steps (such as notifying appropriate mailing lists or newsgroups) reasonably calculated to inform those who received the covered code that new knowledge has been obtained. (b) Contributor APIs. If contributor's modifications include an application programming interface and contributor has knowledge of patent licenses which are reasonably necessary to implement that API, contributor must also include this information in the LEGAL file. code with other code not governed by the terms of this license and distribute the larger work as a single product. In such a case, you must make sure the requirements of this license are fulfilled for the covered code. (c) Representations. contributor represents that, except as disclosed pursuant to section 3.4(a) above, contributor believes that contributor's modifications are contributor's original creation(s) and/or contributor has sufficient rights to grant the rights conveyed by this license. 3.5. Required notices. You must duplicate the notice in exhibit A in each file of the source code. If it is not possible to put such notice in a particular source code file due to its structure, then You must include such notice in a location (such as a relevant directory) where a user would be likely to look for such a notice. If You created one or more modification(s), you may add your name as a contributor to the notice described in exhibit A. you must also duplicate this license in any documentation for the source code where You describe recipients' rights or ownership rights relating to covered code. You may choose to offer, and to charge a fee for, warranty, support, indemnity or liability obligations to one or more recipients of covered code. However, you may do so only on your own behalf, and not on behalf of the Initial developer or any contributor. You must make it absolutely clear than any such warranty, support, indemnity or liability obligation is offered by you alone, and You hereby agree to indemnify the Initial developer and every contributor for any liability incurred by the Initial developer or such contributor as a result of warranty, support, indemnity or liability terms you offer. 3.7. 5. Application of this license. This license applies to code to which the initial developer has attached the notice in exhibit A and to related covered code. 6. Versions of the license. 6.1. New versions. Netscape communications corporation (âNetscapeâ) may publish revised and/or new versions of the license from time to time. Each version will be given a distinguishing version number. 6.2. Effect of new versions. Once covered code has been published under a particular version of the license, you may always continue to use it under the terms of that version. You may also choose to use such covered code under the terms of any subsequent version of the license published by netscape. No one other than netscape has the right to modify the terms applicable to covered code created under this license. APPENDIX 3.6. Distribution of executable versions. You may distribute covered code in executable form only if the requirements of section 3.1-3.5 have been met for that covered code, and if you include a notice stating that the source code version of the covered code is available under the terms of this license, including a description of how and where you have fulfilled the obligations of section 3.2. The notice must be conspicuously included in any notice in an executable version, related documentation or collateral in which you describe recipients' rights relating to the covered code. You may distribute the executable version of covered code or ownership rights under a license of your choice, which may contain terms different from this license, provided that you are in compliance with the terms of this license and that the license for the executable version does not attempt to limit or alter the recipient's rights in the source code version from the rights set forth in this license. If you distribute the executable version under a different license you must make it absolutely clear that any terms which differ from this license are offered by you alone, not by the Initial developer or any contributor. You hereby agree to indemnify the initial developer and every contributor for any liability incurred by the initial developer or such contributor as a result of any such terms You offer. 4. Inability to comply due to statute or regulation. If it is impossible for you to comply with any of the terms of this license with respect to some or all of the covered code due to statute, judicial order, or regulation then you must: (a) comply with the terms of this license to the maximum extent possible; and (b) describe the limitations and the code they affect. Such description must be included in the LEGAL file described in section 3.4 and must be included with all distributions of the source code. Except to the extent prohibited by statute or regulation, such description must be sufficiently detailed for a recipient of ordinary skill to be able to understand it. 6.3. Derivative works. If You create or use a modified version of this license (which you may only do in order to apply it to code which is not already covered code governed by this license), You must (a) rename Your license so that the phrases "Mozilla", "MOZILLAPL", "MOZPL", "Netscape", "MPL", "NPL" or any confusingly similar phrase do not appear in your license (except to note that your license differs from this license) and (b) otherwise make it clear that Your version of the license contains terms which differ from the Mozilla Public license and netscape Public License. (Filling in the name of the initial developer, original code or contributor in the notice described in exhibit A shall not of themselves be deemed to be modifications of this license.) Larger works. You may create a larger work by combining covered 169 APPENDIX 7. DISCLAIMER OF WARRANTY. COVERED CODE IS PROVIDED UNDER THIS LICENSE ON AN âAS ISâ BASIS, WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, WARRANTIES THAT THE COVERED CODE IS FREE OF DEFECTS, MERCHANTABLE, FIT FOR A PARTICULAR PURPOSE OR NON-INFRINGING. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE COVERED CODE IS WITH YOU. SHOULD ANY COVERED CODE PROVE DEFECTIVE IN ANY RESPECT, YOU (NOT THE INITIAL DEVELOPER OR ANY OTHER CONTRIBUTOR) ASSUME THE COST OF ANY NECESSARY SERVICING, REPAIR OR CORRECTION. THIS DISCLAIMER OF WARRANTY CONSTITUTES AN ESSENTIAL PART OF THIS LICENSE. NO USE OF ANY COVERED CODE IS AUTHORIZED HEREUNDER EXCEPT UNDER THIS DISCLAIMER. 8. TERMINATION. 8.1. This license and the rights granted hereunder will terminate automatically if you fail to comply with terms herein and fail to cure such breach within 30 days of becoming aware of the breach. All sublicenses to the covered code which are properly granted shall survive any termination of this license. Provisions which, by their nature, must remain in effect beyond the termination of this license shall survive. 8.2. If you initiate litigation by asserting a patent infringement claim (excluding declatory judgment actions) against initial developer or a contributor (the initial developer or contributor against whom you file such action is referred to as âParticipantâ) alleging that: APPENDIX 170 (a) such participant's contributor version directly or indirectly infringes any patent, then any and all rights granted by such participant to you under sections 2.1 and/or 2.2 of this license shall, upon 60 days notice from Participant terminate prospectively, unless if within 60 days after receipt of notice you either: (i) agree in writing to pay participant a mutually agreeable reasonable royalty for your past and future use of modifications made by such participant, or (ii) withdraw your litigation claim with respect to the contributor version against such participant. If within 60 days of notice, a reasonable royalty and payment arrangement are not mutually agreed upon in writing by the parties or the litigation claim is not withdrawn, the rights granted by participant to you under sections 2.1 and/or 2.2 automatically terminate at the expiration of the 60 day notice period specified above. (b) any software, hardware, or device, other than such participant's contributor Version, directly or indirectly infringes any patent, then any rights grant- ed to You by such participant under sections 2.1(b) and 2.2(b) are revoked effective as of the date you first made, used, sold, distributed, or had made, modifications made by that participant. 8.3. If you assert a patent infringement claim against participant alleging that such participant's contributor version directly or indirectly infringes any patent where such claim is resolved (such as by license or settlement) prior to the initiation of patent infringement litigation, then the reasonable value of the licenses granted by such participant under sections 2.1 or 2.2 shall be taken into account in determining the amount or value of any payment or license. 8.4. In the event of termination under sections 8.1 or 8.2 above, all end user license agreements (excluding distributors and resellers) which have been validly granted by you or any distributor hereunder prior to termination shall survive termination. 9. LIMITATION OF LIABILITY. UNDER NO CIRCUMSTANCES AND UNDER NO LEGAL THEORY, WHETHER TORT (INCLUDING NEGLIGENCE), CONTRACT, OR OTHERWISE, SHALL YOU, THE INITIAL DEVELOPER, ANY OTHER CONTRIBUTOR, OR ANY DISTRIBUTOR OF COVERED CODE,OR ANY SUPPLIER OF ANY OF SUCH PARTIES, BE LIABLE TO ANY PERSON FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES OF ANY CHARACTER INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF GOODWILL, WORK STOPPAGE, COMPUTER FAILURE OR MALFUNCTION, OR ANY AND ALL OTHER COMMERCIAL DAMAGES OR LOSSES, EVEN IF SUCH PARTY SHALL HAVE BEEN INFORMED OF THE POSSIBILITY OF SUCH DAMAGES. THIS LIMITATION OF LIABILITY SHALL NOT APPLY TO LIABILITY FOR DEATH OR PERSONAL INJURY RESULTING FROM SUCH PARTY'S NEGLIGENCE TO THE EXTENT APPLICABLE LAW PROHIBITS SUCH LIMITATION. SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THIS EXCLUSION AND LIMITATION MAY NOT APPLY TO YOU. 10. U.S. GOVERNMENT END USERS. The covered code is a "commercial item," as that term is defined in 48 C.F.R. 2.101 (Oct. 1995), consisting of "commercial computer software" and "commercial computer software documentation," as such terms are used in 48 C.F.R. 12.212 (Sept. 1995). Consistent with 48 C.F.R. 12.212 and 48 C.F.R. 227.7202-1 through 227.7202-4 (June 1995), all U.S. Government end users acquire covered code with only those rights set forth herein. 11. MISCELLANEOUS. This license represents the complete agreement concerning subject matter hereof. If any provision of this license is held to be unenforceable, such provision shall be reformed only to the extent necessary to make it enforceable. This License shall be governed by California law provisions (except to the extent applicable law, if any, provides otherwise), excluding its conflict-of-law provisions. With respect to disputes in which at least one party is a citizen of, or an entity chartered or registered to do business in the united states of america, any litigation relating to this License shall be subject to the jurisdiction of the federal courts of the northern district of california, with venue lying in santa clara county, california, with the losing party responsible for costs, including without limitation, court costs and reasonable attorneys' fees and expenses. The application of the united nations convention on contracts for the International sale of goods is expressly excluded. Any law or regulation which provides that the language of a contract shall be construed against the drafter shall not apply to this license. 12. RESPONSIBILITY FOR CLAIMS. As between initial developer and the contributors, each party is responsible for claims and damages arising, directly or indirectly, out of its utilization of rights under this license and you agree to work with initial developer and contributors to distribute such responsibility on an equitable basis. Nothing herein is intended or shall be deemed to constitute any admission of liability. The contents of this file are subject to the Mozilla Public License Version 1.1 (the âlicenseâ); you may not use this file except in compliance with the License. You may obtain a copy of the license at http://www.mozilla.org/MPL/ Software distributed under the license is distributed on an "AS IS" basis, WITHOUT WARRANTY OF ANY KIND, either express or implied. See the license for the specific language governing rights and limitations under the License. The Original Code is ______________________________________ The Initial Developer of the Original Code is___________________. Portions created by ______________________ are Copyright (C) _______________________. All Rights Reserved. Contributor(s): ______________________________________. Alternatively, the contents of this file may be used under the terms of the _____ license (the "[___] License"), in which case the provisions of [______] license are applicable instead of those above. If you wish to allow use of your version of this file only under the terms of the [____] license and not to allow others to use your version of this file under the MPL, indicate your decision by deleting the provisions above and replace them with the notice and other provisions required by the [___] license. If you do not delete the provisions above, a recipient may use your version of this file under either the MPL or the [___] license." NOTE: The text of this exhibit A may differ slightly from the text of the notices in the source code files of the original code. You should use the text of this exhibit A rather than the text found in the original code/source code for Your modifications. APPENDIX 13. MULTIPLE-LICENSED CODE. Initial developer may designate portions of the covered code as "Multiple-Licensed". "MultipleLicensed" means that the initial developer permits you to utilize portions of the covered code under your choice of the NPL or the alternative licenses, if any, specified by the initial developer in the file described in exhibit A. EXHIBIT A -Mozilla Public License. 171 Regulatory Information cont. FCC Compliance Statement respecte toutes les exigences du Règlement sur le matĂŠriel brouilleur du Canada. This equipment has been tested and found to comply within the limits of a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. NOTICE The regulations are applied only to the products with the ID LABEL indicating specific requirements. CE Conformity Notice (for Europe) This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. Products with the âCEâ Marking comply with the EMC Directive(89/336/EEC) and LOW VOLTAGE Directive (73/23/EEC) issued by the Commission of the European Community. Compiance with these directives implies conformity to the following European Norms : ⢠EN 55022 ; Radio Frequency Interference ⢠EN 55024 ; Electromagnetic Immunity ⢠EN 61000-3-2 ; Power Line Harmonics ⢠EN 61000-3-3 ; Voltage Fluctuations ⢠EN 60950-1 ; Product Safety If this equipment does cause harmful interference to radio or television reception (which can be determined by turning the equipment on and off), the user is encouraged to try to correct the interference by using one or more of the following measures: NOTICE The regulations are applied only to the products with the ID LABEL indicating specific requirements. Reorient or relocate the receiving antenna. Increase the separation between the equipment and the receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Low Radiation Compliance (MPR II) This monitor meets one of the strictest guidelines available today for low radiation emissions, offering the user extra shielding and an antistatic screen coating. These guidelines, set forth by a government agency in Sweden, limit the amount of emission allowed in the Extremely Low Frequency (ELF) and Very Low Frequency (VLF) electromagnetic range. Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user's (or your) authority to operate the equipment. Only peripherals (digital input/output devices, terminals, printers, etc.) certified to comply with the Class B limits may be attached to this monitor. Operation with non-certified peripherals is likely to result in interference to radio and TV reception. Only shielded signal cables may be used with this System. TCO'99 (TCO'99 applied model only) NOTICE The regulations are applied only to the products with the ID LABEL indicating specific requirements. Congratulations! You have just purchased a TCOâ99 approved and labelled product! Your choice has provided you with a product developed for professional use. Your purchase has also contributed to reducing the burden on the environment and also to the further development of environmentally adapted electronics products. Canadian DOC Notice This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numĂŠrique de la classe B 01 Regulatory Information cont. Why do we have environmentally labelled computers? In many countries, environmental labelling has become an established method for encouraging the adaptation of goods and services to the environment. With the growing manufacture and usage of electronic equipment throughout the world, there is a recognized concern for the materials and substances used by electronic products with regards to their eventual recycling and disposal. By proper selection of these materials and substances, the impact on the environment can be minimized. visual ergonomics. Below you will find a brief summary of the ecological requirements met by this product. The complete ecological criteria document can be found at TCO Developmentâs website http://www.tcodevelopment.com or may be ordered from: TCO Development SE-114 94 STOCKHOLM, Sweden Fax: +46 8 782 92 07 Email : development@tco.se Information regarding TCOâ99 approved and labelled products may also be obtained at http://www.tcodevelopment.com There are also other characteristics of a computer, such as energy consumption levels, that are important from the viewpoints of both the work (internal) and natural (external) environments. Electronic equipment in offices is often left running continuously, resulting in unnecessary consumption of large amounts of energy and additional power generation. From the standpoint of carbon dioxide emissions alone, it is vital to save energy. Ecological requirements Flame retardants Flame retardants may be present in printed wiring board laminates, cables, and housings. Their purpose is to prevent, or at least to delay the spread of fire. Up to 30% by weight of the plastic in a computer casing can consist of flame retardant substances. Many flame retardants contain bromine or chlorine, and these flame retardants are chemically related to PCBs (polychlorinated biphenyls). Both the flame retardants containing bromine or chlorine and the PCBs are suspected of giving rise to health effects, including reproductive damage in fisheating birds and mammals, due to the bio-accumulative* processes when not disposed of in accordance with strict standards for disposal. What does labelling involve? The product meets the requirements for the TCOâ99 scheme which provides for international and environmental labelling of personal computers and/or displays. The labelling scheme was developed as a joint effort by the TCO (The Swedish Confederation of Professional Employees), Svenska Naturskyddsforeningen (The Swedish Society for Nature Conservation) and Statens Energimyndighet (The Swedish National Energy Administration). Approval requirements cover a wide range of issues: ecology, ergonomics, emission of electrical and magnetical fields, energy consumption and electrical safety. TCOâ99 requires that plastic components weighing more than 25 grams shall not contain flame retardants with organically bound bromine or chlorine. Flame retardants are allowed in the printed wiring board laminates due to the lack of commercially available alternatives. Ecological criteria impose restrictions on the presence and use of heavy metals, brominated and chlorinated flame retardants, and other substances. The product must be prepared for recycling and the manufacturing site(s) shall be certified according to ISO14001 or EMAS registered. Cadmium** Cadmium is present in rechargeable batteries and in the colour-generating layers of certain computer displays. TCOâ99 requires that batteries, the colour-generating layers of display screens, and the electrical or electronics components shall not contain any cadmium. Energy requirements include a demand that the system unit and/or display, after a certain period of inactivity, shall reduce its power consumption to a lower level in one or more stages. The length of time to reactivate the system unit shall be reasonable for the user. Mercury** Mercury is sometimes found in batteries, relays and switches. TCOâ99 requires that batteries shall not contain any mercury. It also demands that mercury is not present in any of the electrical or electronics components associated with the labelled unit. There is however one Labelled products must meet strict environmental demands, for example, in respect of the reduction of electrical and magnetical fields as well as work load and 02 Regulatory Information cont. ⢠exception. Mercury is, for the time being, permitted in the back light system of flat panel monitors as there today is no commercially available alternative. TCO aims on removing this exception when a mercury free alternative is available. Noise emissions Ecology ⢠The product must be prepared for recycling and the manufacturer must have a certified environmental management system such as EMAS or ISO 14 001 ⢠Restrictions on chlorinated and brominated flame retardants and polymers heavy metals such as cadmium, mercury and lead. Lead** Lead can be found in picture tubes, display screens, solders and capacitors. TCOâ99 permits the use of lead due to the lack of commercially available alternatives, but in future requirements TCO Development aims at restricting the use of lead. _____________________________________________ The requirements included in this label have been developed by TCO Development in co-operation with scientists, experts, users as well as manufacturers all over the world. Since the end of the 1980s TCO has been involved in influencing the development of IT equipment in a more user-friendly direction. Our labelling system started with displays in 1992 and is now requested by users and IT-manufacturers all over the world. * Bio-accumulative is defined as substances which accumulate in living organisms. **Lead, Cadmium and Mercury are heavy metals which are bio-accumulative. TCOâ03 (TCOâ03 applied model only) For more information, please visit www.tcodevelopment.com English Congratulations! The display you have just purchased carries the TCOâ03 Displays label. This means that your display is designed,manufactured and tested according to some of the strictest quality and environmental requirements in the world. This makes for a high performance product, designed with the user in focus that also minimizes the impact on our natural environment. Some of the features of the TCOâ03 Display requirements: Information for Environmental Preservation LGE. announced the 'LG Declaration for a Cleaner Environment' in 1994, and this ideal has served as a guiding managerial principle ever since. The Declaration is a foundation that has allowed us to undertake environmentally friendly activities in careful consideration of economic, environmental, and social aspects. We promote activities for environmental preservation, and we specifically develop our products to embrace the concept of environment-friendly. We minimize the hazardous materials contained in our products. For example, there is no cadmium to be found in our monitors. Ergonomics ⢠Good visual ergonomics and image quality in order to improve the working environment for the user and to reduce sight and strain problems. Important parameters are luminance, contrast, resolution, reflectance, colour rendition and image stability. Information for recycling This monitor may contain parts which could be hazardous to the environment. It is important that this monitor be recycled after use. Energy ⢠Energy-saving mode after a certain time â beneficial both for the user and the environment ⢠Electrical safety LGE. handles all waste monitors through an environmentally acceptable recycling method. There are several take-back and recycling systems currently in Emissions ⢠Electromagnetic fields 03 Regulatory Information cont. operation worldwide. Many parts will be reused and recycled, while harmful substances and heavy metals are treated by an environmentally friendly method. If you want to find out more information about our recycling program, please contact your local LG vendor or a corporate representative of LG. Wir richten unsere Firmenpolitik auf eine sauberere Umwelt hin aus, indem wir umweltspezifische Aspekte als wichtigen Punkt in die Weiterentwicklung unseres Unternehmens einflieĂen lassen. Zusätzliche Informationen Ăźber unsere âgrĂźneâ Firmenpolitik erhalten Sie auf unserer Website. http://www.lge.com/about/environment/html/Recycling.jsp We set our vision and policies on a cleaner world by selecting the issue of the global environment as a task for corporate improvement. Please visit our website for more information about our âgreenâ policies. http://www.lge.com/about/environment/html/Recycling.jsp Français Information sur la protection delâenvironnement LGE. a publiĂŠ sa 'DĂŠclaration en faveur dâun environnement plus propre' en 1994 et celle-ci est restĂŠe, depuis lors, un principe directeur de notre entreprise. Cette dĂŠclaration a servi de base Ă notre rĂŠflexion et nous a permis de prendre en compte Ă la fois les aspects ĂŠconomiques et sociaux de nos activitĂŠs, tout en respectant lâenvironnement. Deutsch Informationen zur Erhaltung der Umwelt Im Jahr 1994 verkĂźndete LGE die 'LG Declaration for a Cleaner Environment' (LG Erklärung fĂźr eine sauberere Umwelt). Seitdem dient dieses Ideal als fĂźhrendes Prinzip des Unternehmens. Diese Erklärung war die Basis fĂźr die DurchfĂźhrung von umweltfreundlichen Aktivitäten, wobei wirtschaftliche, umweltbezogene und soziale Aspekte in die Ăberlegungen mit einbezogen wurden. Wir fĂśrdern Aktivitäten zum Schutz der Umwelt und die Entwicklung unserer Produkte ist darauf ausgerichtet, unserem Konzept bezĂźglich Umweltfreundlichkeit gerecht zu werden. Wir sind darauf bedacht, den Anteil der in unseren Produkten enthaltenen schädlichen Materialien zu minimieren. So ist in unseren Monitoren beispielsweise kein Kadmium zu finden. Nous encourageons les activitĂŠs en faveur de la prĂŠservation de lâenvironnement et câest dans cet esprit que nous dĂŠveloppons nos produits : nous rĂŠduisons au minimum les matières dangereuses qui entrent dans leur composition et lâon ne trouve pas de cadmium, par exemple, dans nos moniteurs. Information sur le recyclage Ce moniteur peut contenir des composants qui prĂŠsentent un risque pour lâenvironnement. Il est donc important que celui-ci soit recyclĂŠ après usage. LGE. traite les moniteurs en fin de cycle conformĂŠment Ă une mĂŠthode de recyclage respectueuse de lâenvironnement. Nous reprenons nos produits et les recyclons dans plusieurs sites rĂŠpartis dans le monde entier. De nombreux composants sont rĂŠutilisĂŠs et recyclĂŠs, et les matières dangereuses, ainsi que les mĂŠtaux lourds, sont traitĂŠs selon un procĂŠdĂŠ ĂŠcologique. Si vous souhaitez plus de renseignements sur notre programme de recyclage, veuillez contacter votre revendeur LG ou un lâun de nos reprĂŠsentants. Informationen zum Thema Recycling Dieser Monitor enthält Teile, die umweltschädlich sein kĂśnnen. Es ist unbedingt erforderlich, dass der Monitor recycelt wird, nachdem er auĂer Dienst gestellt wurde. Bei LGE. werden alle ausrangierten Monitore in einem unter umweltbezogenen Aspekten geeigneten Verfahren recycelt. Augenblicklich sind weltweit mehrere RĂźcknahme- und Recyclingsysteme im Einsatz. Viele Teile werden wieder verwendet und recycelt. Schädliche Substanzen und Schwermetalle werden durch umweltverträgliche Verfahren behandelt. Falls Sie mehr Ăźber unser Recyclingprogramm erfahren mĂśchten, wenden Sie sich bitte an Ihren lokalen LGHändler oder einen Unternehmensvertreter von LG. Nous voulons agir pour un monde plus propre et croyons au rĂ´le de notre entreprise dans lâamĂŠlioration de lâenvironnement. Pour plus de renseignements sur notre politique âverteâ, rendez visite Ă notre site : http://www.lge.com/about/environment/html/Recycling.jsp 04 Regulatory Information cont. Italiano respetan el medio ambiente siempre teniendo en cuenta aspectos sociales, econĂłmicos y medioambientales. Informazioni per la tutela dellâambiente La LGE. ha annunciato nel 1994 la cosiddetta 'LG Declaration for a Cleaner Environment' (Dichiarazione di LG a favore di un ambiente piĂš pulito), un ideale che da allora funge da principio ispiratore della gestione aziendale. La dichiarazione rappresenta il fondamento che consente di intraprendere attivitĂ a favore dell'ambiente tenendo conto degli aspetti economici, ambientali e sociali.Noi della LG, promuoviamo attivitĂ a favore della tutela dell'ambiente sviluppando appositamente i nostri prodotti per cogliere il concetto del rispetto dellâambiente riducendo i materiali dannosi presenti nei nostri prodotti. Ad esempio nei nostri monitor non è presente il cadmio. Promocionamos actividades orientadas a la conservaciĂłn del medio ambiente y desarrollamos nuestros productos especĂficamente para que se ajusten a la filosofĂa que protege el entorno. Reducimos al mĂĄximo el uso de materiales de riesgo en nuestros productos. Un ejemplo de ello es la ausencia total de cadmio en nuestros monitores. InformaciĂłn para el reciclaje Este monitor puede contener piezas que entraĂąen riesgos medioambientales. Es importante reciclar este monitor despuĂŠs de su utilizaciĂłn. LGE. trata todos los monitores usados siguiendo un mĂŠtodo de reciclaje que no daĂąa al entorno. Contamos con diversos sistemas de recuperaciĂłn y reciclaje que funcionan a nivel mundial en la actualidad. Es posible reciclar y reutilizar muchas de las piezas, mientras que las sustancias daĂąinas y los metales pesados se tratan siguiendo un mĂŠtodo que no perjudique al medio ambiente. Si desea obtener mĂĄs informaciĂłn acerca del programa de reciclaje, pĂłngase en contacto con su proveedor local de LG o con un representante empresarial de nuestra marca. Informazioni per il riciclaggio Il monitor può presentare componenti che potrebbero risultare eventualmente dannosi per l'ambiente. Ă importante che il monitor sia riciclato al termine del suo utilizzo. La LGE. gestisce tutti i monitor di rifiuto con un metodo di riciclaggio soddisfacente dal punto di vista ambientale. In tutto il mondo sono attualmente in funzione numerosi sistemi di riciclaggio e recupero. I diversi componenti sono riutilizzati e riciclati, mentre le sostanze dannose e i metalli pesanti vengono trattati con un metodo rispettoso dellâambiente. Se si desiderano maggiori informazioni in merito al programma di riciclaggio, è consigliabile rivolgersi al proprio rivenditore LG o ad un rappresentante aziendale della LG. Basamos nuestra visiĂłn y nuestras polĂticas en un mundo mĂĄs limpio y para ellos optamos por un entorno global como tarea principal de nuestra evoluciĂłn como empresa. Visite nuestra pĂĄgina Web para obtener mĂĄs informaciĂłn sobre nuestras polĂticas ecolĂłgicas. http://www.lge.com/about/environment/html/Recycling.jsp Noi della LG impostiamo la nostra visione e le nostre politiche a favore di un mondo piĂš pulito ponendo la questione dell'ambiente dal punto di vista globale come una mansione rivolta al miglioramento della nostra azienda. Vi invitiamo a visitare il nostro sito internet per ulteriori informazioni sulla nostra politica âverdeâ. http://www.lge.com/about/environment/html/Recycling.jsp PortuguĂŞs Informaçþes relacionadas Ă preservação ambiental A LGE. anunciou a 'LG Declaration for a Cleaner Environment' (Declaração da LG para um ambiente mais limpo) em 1994 e esse ideal tem servido desde entĂŁo como um princĂpio administrativo de orientação. A Declaração ĂŠ a base que nos tem permitido realizar atividades favorĂĄveis ao ambiente com consideração atenta aos aspectos econĂ´micos, ambientais e sociais. EspanĂľl InformaciĂłn para la conservaciĂłn medioambiental LGE. presentĂł la 'DeclaraciĂłn para un entorno mĂĄs limpio de LG' en 1994 y este ideal ha servido para guiar nuestros principios empresariales desde entonces. La DeclaraciĂłn es la base que nos ha permitido llevar a cabo tareas que Promovemos atividades de preservação ambiental e desenvolvemos nossos produtos para englobar 05 Regulatory Information cont. especificamente o conceito de favorĂĄvel ao ambiente. Reduzimos os materiais perigosos contidos em nossos produtos. Por exemplo, nĂŁo hĂĄ cĂĄdmio em nossos monitores. Informatie met betrekking tot recycling Deze monitor bevat materialen die schadelijk zouden kunnen zijn voor het milieu. Het is belangrijk dat deze monitor aan het einde van zijn levensduur wordt gerecycled. Informaçþes relacionadas Ă reciclagem Este monitor pode conter peças que podem representar riscos ao ambiente. Ă importante que ele seja reciclado apĂłs o uso. LGE. verwerkt alle afvalmonitors via een milieuvriendelijke recyclingmethode. Hiervoor worden er momenteel wereldwijd verscheidene inname- en recyclingsystemen gehanteerd. Een groot aantal onderdelen wordt opnieuw gebruikt en gerecycled, waarbij schadelijke stoffen en zware metalen volgens een milieuvriendelijke methode worden verwerkt. Voor meer informatie over ons recyclingprogramma kunt u contact opnemen met uw plaatselijke LGvertegenwoordiger of een LG-vestiging. A LGE. cuida de todos os monitores descartados atravĂŠs de um mĂŠtodo de reciclagem agradĂĄvel ao ambiente. HĂĄ vĂĄrios sistemas de devolução e reciclagem atualmente em operação no mundo. Muitas peças serĂŁo reutilizadas e recicladas e as substâncias nocivas e os metais pesados passarĂŁo por tratamento atravĂŠs de um mĂŠtodo favorĂĄvel ao ambiente. Para obter mais informaçþes sobre nosso programa de reciclagem, entre em contato com seu fornecedor LG local ou com um representante corporativo da LG. Definimos nossa visĂŁo e nossas polĂticas relacionadas a um mundo mais limpo selecionando a questĂŁo do ambiente global como uma tarefa de aprimoramento corporativo. Visite nosso site para obter mais informaçþes sobre nossas polĂticas de meio ambiente. http://www.lge.com/about/environment/html/Recycling.jsp Onze visie en ons beleid met betrekking tot een schonere wereld vloeien voort uit het feit dat wij het milieu hebben aangemerkt als een onderwerp dat speciale aandacht verdient binnen onze onderneming. Bezoek onze website voor meer informatie over ons 'groene' beleid. http://www.lge.com/about/environment/html/Recycling.jsp Russian ÂťĂĂĂĂâĄËĂË ĂĂ ĂĹâĄĂĂ ĂĂĂĂâĄËËĂĂ ĂĂâ°Ë Nederlands ÂŹ 1994 âĂâ°Ă ĂĂĂĂâĄËĂË LGE ĂĂĂ¡ĂĂĂĂââĄĂ⥠'ĆĂĂĂâĄďŁżâĄËĂË LG ĂĂ ĂĹâĄĂĂ ĂĂĂĂâĄËËĂĂ ĂĂâ°Ë', ĂĂĂĂâĄË Ă ĂĂÄą ĂĂ ĂĂĂĂĂĂ ĂĂĂĂâĂËĂ ĂĂĂËĂĂĂĂ ĂĂâĄâĂĂĂĂË. Ă⥠ĂĂĂĂâĂ ËĂĂĂ â°ĂĂĂâĄďŁżâĄËĂĂ ĂË ĂĂĂâĂĂ ĂĂâ°ĂĂĂËø â°ĂĂĂĂâĂË, Ă¡ĂĂĂĂËĂââĄËËĂà ¡ĂĂĂĂâĄĂĂĂĂø ĂĂĂĂâĄËËĂĂ ĂĂâ°Ë, Ăâ°ĂĂËË Ăà ËĂĂĂ â°ĂĂĂĂĂĂ âĂĂĂâĄĂĂĂ ËĂĂĂĂĂĂËĂĂĂĂĂ, ËĂĂĂĂâĂËĂĂĂĂĂ Ă ĂĂËĂâĄĂ¸ĂËĂ âĄĂĂĂĂĂâĄĂ. Informatie met betrekking tot het behoud van het milieu LGE. publiceerde in 1994 de 'LG Declaration for a Cleaner Environment' (de LG-verklaring met betrekking tot een schoner milieu). Deze verklaring en het ideaal van een schoner milieu fungeren sindsdien als een bestuurlijke leidraad voor onze onderneming. Op basis van deze verklaring ontplooien wij milieuvriendelijke activiteiten, waarbij er zowel met sociale en economische aspecten, als met milieuaspecten zorgvuldig rekening wordt gehouden. ĂË ĂĂĂĂĂĂĂĂĂĂ â°ĂËĂĂøĂĂĂø ĂĂ ĂĹâĄĂĂ ĂĂĂĂâĄËËĂĂ ĂĂâ°Ë, Ăâ°ĂĂËË ĂĂĂ¡ĂĂ âĂĂĂâĄĂĂà âĄĂâĄÂˇĂĂĂĂ ĂâĄÂŻĂĂ ĂĂâ°ĂĂËĂĂ â ĂĂĂĂâĂĂĂĂâĂĂ Ă ĂĂĂËĂĂËĂĂĂ ËĂĂĂĂâĂËĂĂĂĂà ¡ĂĂĂĂâĄĂĂĂĂĂĂ. ĂË ĂâĂâ°ĂĂ Ă ĂĂĂĂĂĂĂĂ ĂĂâ°ĂĂâĄĂĂĂ ĂĂâĄĂĂËÄą âĂËĂĂĂâ â ĂâĄÂŻĂĂ ĂĂâ°ĂĂËĂĂ. ĂâĄĂĂĂĂ, â ĂâĄÂŻĂÄą ĂĂĂĂĂĂâĄÄą âË ĂĂ ĂâĄĂâ°ĂĂĂ ĂâĄâ°ĂĂË. Wij ondersteunen activiteiten die zijn gericht op het behoud van het milieu en wij houden bij het ontwikkelen onze producten specifiek rekening met de milieuvriendelijkheid van onze producten. Wij minimaliseren het gebruik van schadelijke stoffen in onze producten. Er wordt bijvoorbeeld geen cadmium verwerkt in onze monitors. ÂťĂĂĂĂâĄËĂË ĂĂ ĂĂĂĂĂĂâĄËĂĂ ĂĂÄąĂâ°Ăâ âşĂĂĂ ĂĂĂĂĂĂ ĂĂĂĂĂ ĂĂâ°ĂĂâĄĂ¸ ĂĂĂĂĂĂĂĂĂË, ĂĂĂĂËĂ ĂĂâĂĂ ĂâĄĂĂĂĂĂ ĂËĂ¡ ĂĂĂĂâĄËËĂĂ ĂĂâ°Ă. 06 Regulatory Information cont. ĂĂĂ¡ĹĂâ°ĂĂĂ ĂĂĂĂĂĂĂĂââĄĂ¸ ĂĂĂĂĂĂ ĂĂĂĂĂ ĂĂĂĂøĂĂââĄĂĂË. KĂĂĂâĄËĂË LGE ĂĂĂâĄÂˇâĄĂËââĄĂĂ âĂà ¡âĄĂĂââĄĂĂËĂ ĂĂĂĂĂĂďŁżË Ă ĂĂĂĂËÂ¸Ë ËĂĂĂĂâĂËĂĂĂĂ ĂĂĂĂĂĂĂĂâĂ ĂĂĂĂâ°âĄ ĂĂĂĂĂĂâĄËĂĂ ĂĂÄąĂâ°Ăâ. ĹĂ âĂĂĂĂ ĂĂà â°ĂĂĂĂâĂËĂ ĂĂĂĂĂĂË ĂĂĂĂĂĂâĄËĂĂ ĂĂÄąĂâ°Ăâ Ă âĂĂââĄĂ⥠ĂĂĂĂøĂĂââĄĂĂĂĂ ĂĂâ°ĂĂËĂĂ. ĂĂĂâĂĂ ĂĂĂĂĂĂĂĂĂË ÂˇĂâ°ĂĂ âĂĂĂËĂĂ ĂĂĂĂøĂĂââĄĂË Ă ĂĂĂĂĂĂĂĂââĄĂË, â ĂĂ âĂĂË ĂâĄĂ âĂâ°ĂËĂ âĂËĂĂĂâ⥠à ĂËĂĂĂËĂ ĂĂĂâĄĂĂË ÂˇĂâ°ĂĂ Ă¡âĄÂˇĂĂâĄĂË Ă ĂĂĂĂËÂ¸Ë ËĂĂĂĂâĂËĂĂĂĂ ĂĂĂĂĂĂĂĂâĂ ĂĂĂĂâ°âĄ. ⥠¡ĂĂĂĂ ĂĂâ°ďŁżĂ¡ĂĂĂ ĂĂĂĂĂâĄËĂĂĂ ĂĂ ĂâĄÂŻĂĂ ĂĂââĄĂĂĂ ĂĂĂĂĂĂâĄËĂĂ ĂĂÄąĂâ°Ăâ Ă¡âĄËâĄĂĂĂø Ă ĂĂĂĂĂĂĂĂ ĂĂĂĂâĄâËĂĂĂ ĂĂĂ ĂĂâ°ĂĂâĄâĂĂĂĂË ĂĂĂĂâĄËĂĂ LG. ĂË ĂĂĂĂĂĂĂĂĂĂË Ă⥠Ă¡ĂĂĂĂËĂĂĂĂ ËĂĂĂĂâĂËĂĂĂĂà ¡ĂĂĂĂâĄĂĂĂĂĂĂ, ĂĂâĄâË ĂĂ¡à ËĂĂÂ¸Ë âĂĂ¡âĄĂ¸ĂĂË ĂâĄËĂĂĂ ĂĂĂĂâĄËËĂĂ ĂĂâ°Ë. ĆĂĂĂĂĂĂĂĂøĂĂË ĂĂĂĂĂâĄËĂË Ă ĂâĄÂŻĂĂ ĂĂĂĂĂĂĂĂ ĂĂ ĂĹâĄĂĂ ĂĂĂĂâĄËËĂĂ ĂĂâ°Ë âË ĂĂĂĂĂĂ ĂâĄĂĂĂ Ă⥠ĂâĄÂŻĂĂ ĂâĄĂĂĂ: http://www.lge.com/about/environment/html/Recycling.jsp EPA (EPA applied model only) ENERGY STAR is a set of power-saving guidelines issued by the U.S. Environmental Protection Agency(EPA). As an ENERGY STAR Partner LGE U. S. A.,Inc. has determined that this product meets the ENERGY STAR guidelines for energy efficiency. NOM MARK (Mexico only) 07 Regulatory Information cont. WEEE un bidone della spazzatura barrato da una croce significa che il prodotto è coperto dalla direttiva europea 2002/96/EC. 2.Tutti i prodotti elettrici ed elettronici dovrebbero essere smaltiti separatamente rispetto alla raccolta differenziata municipale, mediante impianti di raccolta specifici designati dal governo o dalle autoritĂ locali. 3.Il corretto smaltimento delle apparecchiature obsolete contribuisce a prevenire possibili conseguenze negative sulla salute umana e sull'ambiente. 4.Per informazioni piĂš dettagliate sullo smaltimento delle apparecchiature obsolete, contattare il comune, il servizio di smaltimento rifiuti o il negozio in cui è stato acquistato il prodotto. (for Europe ) English Disposal of your old appliance 1.When this crossed-out wheeled bin symbol is attached to a product it means the product is covered by the European Directive 2002/96/EC. 2.All electrical and electronic products should be disposed of separately from the municipal waste stream via designated collection facilities appointed by the government or the local authorities. 3.The correct disposal of your old appliance will help prevent potential negative consequences for the environment and human health. 4.For more detailed information about disposal of your old appliance, please contact your city office, waste disposal service or the shop where you purchased the product. Swedish Kassering av din gamla apparat 1.När den här symbolen med en Ăśverkryssad soptunna pĂĽ hjul sitter pĂĽ en produkt innebär det att den regleras av European Directive 2002/96/EC. 2.Alla elektriska och elektroniska produkter bĂśr kasseras via andra vägar än de som finns fĂśr hushĂĽllsavfall, helst via fĂśr ändamĂĽlet avsedda uppsamlingsanläggningar som myndigheterna utser. 3.Om du kasserar din gamla apparat pĂĽ rätt sätt sĂĽ bidrar du till att fĂśrhindra negativa konsekvenser fĂśr miljĂśn och människors hälsa. 4.Mer detaljerad information om kassering av din gamla apparat kan fĂĽr av kommunen, renhĂĽllningsverket eller den butik där du kĂśpte produkten. French Ălimination de votre ancien appareil 1.Ce symbole, reprĂŠsentant une poubelle sur roulettes barrĂŠe d'une croix, signifie que le produit est couvert par la directive europĂŠenne 2002/96/EC. 2.Les ĂŠlĂŠments ĂŠlectriques et ĂŠlectroniques doivent ĂŞtre jetĂŠs sĂŠparĂŠment, dans les videordures prĂŠvus Ă cet effet par votre municipalitĂŠ. 3.Une ĂŠlimination conforme aux instructions aidera Ă rĂŠduire les consĂŠquences nĂŠgatives et risques ĂŠventuels pour l'environnement et la santĂŠ humaine. 4.Pour plus d'information concernant l'ĂŠlimination de votre ancien appareil, veuillez contacter votre mairie, le service des ordures mĂŠnagères ou encore la magasin oĂš vous avez achetĂŠ ce produit. Dutch Uw oude toestel wegdoen 1.Als het symbool met de doorgekruiste verrijdbare afvalbak op een product staat, betekent dit dat het product valt onder de Europese Richtlijn 2002/96/EC. 2.Elektrische en elektronische producten mogen niet worden meegegeven met het huishoudelijk afval, maar moeten worden ingeleverd bij speciale inzamelingspunten die door de lokale of landelijke overheid zijn aangewezen. 3.De correcte verwijdering van uw oude toestel helpt negatieve gevolgen voor het milieu en de menselijke gezondheid voorkomen. Italian Smaltimento delle apparecchiature obsolete 1.Quando su un prodotto è riportato il simbolo di 08 Regulatory Information cont. 4.Wilt u meer informatie over de verwijdering van uw oude toestel? Neem dan contact op met uw gemeente, de afvalophaaldienst of de winkel waar u het product hebt gekocht. eller de lokale myndigheder. 3.Korrekt bortskaffelse af dit gamle apparat er med til at forhindre mulige skadevirkninger pĂĽ miljøet og menneskelig sundhed. 4.Mere detaljerede oplysninger om bortskaffelse af dit gamle apparat kan fĂĽs ved at kontakte dit lokale kommunekontor, renovationsselskab eller den butik, hvor du købte produktet. Finnish Vanhojen laitteiden hävittäminen 1.Tämä merkki tuotteessa tarkoittaa, että tuote kuuluu sähkĂś- ja elektroniikkalaiteromusta annetun EU-direktiivin 2002/96/EY soveltamisalaan. 2.Kaikki elektroniset laitteet ovat ongelmajätettä, joten ne on toimitettava paikalliseen keräyspisteeseen. 3.Vanhan laitteen asianmukainen hävittäminen ehkäisee mahdollisia ympäristÜÜn ja terveyteen kohdistuvia haittavaikutuksia. 4.Lisätietoa vanhan laitteen hävittämisestä saat ottamalla yhteyden paikallisiin viranomaisiin, kierrätyskeskukseen tai myymälään, josta ostit laitteen. Greek âďŹĂĂĂâĂ ĂĂË ďŁżÂˇĂĂÂżË ĂÂˇË ĂËĂĂĂËâšË 1.ŸĂ¡à ¤Ă¡ ĂĂËďŹĂ â°Ă¡Ĺ¤ĂĂĂ ĂĂ â°âĄĂâĂĂĂ ĂĂďŹË â°Ă¡ĂĂ¡ĂäĂĂË ĂÂżĂ¡ĹĂË ÂˇďŁżĂĂĂĂĂĂÂżĂËĂ, ĂďŹĂĂ Ăà ĂĂËďŹĂ Ă¡ĂâĄďŁżĂĂĂÂˇĂ ÂˇďŁżďŹ ĂĂĂ EËĂË¡ËĂâš Oâ°ĂĂâşÂˇ 2002/96/EOK. 2.H ¡ďŹĂĂĂâĂ ďŹĂËĂ ĂËĂ ĂĂĂĂĂĂĂĂĂĂ Ă¡à ĂĂĂĂĂĂĂĂĂĂĂà ĂĂËďŹĂĂËà äĂĂ Ă¡ ĂâşĂĂĂ¡à ¯ËĂĂĂĂÂż ÂˇďŁżďŹ Ă¡ ĂĂĂĂĂÂż ĂĂĂĂ¡ĂÂż ¡ĂĂĂâşĂĂ¡Ă¡ äĂË Ă¡ĹĂĂĂĂäĂËĂ ĂĂĂ¡Ă¡ĂĂÂżĂĂËĂ ĂËĂĂĂĂâšË ¡ĂĂĂĂĂĂÂżĂËĂ, ĂĂ ĂĂâşĂË Â¤ÂŻĂËĂ â°ĂĂĂĂËĂĂĂÄąĂâş ĂâşĂĂ ÂˇďŁżďŹ ĂĂĂ ĂËâ¤ĂĂĂĂĂ âš ÂˇďŁżďŹ ĂĂË ĂĂĂĂÂ¤Ë ÂˇĂ¯¤Ë. 3.H ĂËĂĂ⚠¡ďŹĂĂĂâĂ ĂĂË ďŁżÂˇĂĂÂżË ĂÂˇË ĂËĂĂĂËâšË Ĺ¡ âĂĂÄąâšĂĂĂ ĂĂĂà ¡ĂĂĂĂ⚠ĂĹ¡ĂĂà ¡ĂĂĂĂĂĂĂĂ ĂËĂĂĂĂĂ ËË ďŁżĂĂË Ăà ĂĂĂâÂżĂĂĂĂ Ă¡à ĂĂĂ ËĂĂâşÂˇ ĂĂË ÂˇĂÄąĂĂĂË. 4.°Ă¡ ĂĂ ĂĂĂĂĂĂĂĂâşË ĂĂĂĂĂĂĂâşĂË ĂÂŻĂĂĂĂÂż ĂĂ ĂĂà ¡ďŹĂĂĂâĂ ĂĂË ďŁżÂˇĂĂÂżË ĂÂˇË ĂËĂĂĂËâšË, ĂĂĂĂĂĂËĂâšĂĂĂ ĂĂ Ăà ¡ĂĂďŹâ°âşĂ ĂĂĂĂďŹ ĂĂ¡ĂĂâşĂ, ËĂĂĂĂâşÂˇ â°Ă¿ĹĂĂĂË ĂĂĂĂ¡ĂĂà ¡ĂĂĂĂĂĂÂżĂËĂ âš ĂĂ Ă¡Ă¡Ăâş ÂˇďŁżďŹ ĂĂ ĂĂâşĂ ¡ĂĂĂÂżĂ¡ĂĂ Ăà ĂĂËďŹĂ. German Entsorgung von Altgeräten 1.Wenn dieses Symbol eines durchgestrichenen Abfalleimers auf einem Produkt angebracht ist, unterliegt dieses Produkt der europäischen Richtlinie 2002/96/EC. 2.Alle Elektro- und Elektronik-Altgeräte mĂźssen getrennt vom HausmĂźll Ăźber dafĂźr staatlich vorgesehenen Stellen entsorgt werden. 3.Mit der ordnungsgemäĂen Entsorgung des alten Geräts vermeiden Sie Umweltschäden und eine Gefährdung der persĂśnlichen Gesundheit. 4.Weitere Informationen zur Entsorgung des alten Geräts erhalten Sie bei der Stadtverwaltung, beim Entsorgungsamt oder in dem Geschäft, wo Sie das Produkt erworben haben. Spanish CĂłmo deshacerse de aparatos elĂŠctricos y electrĂłnicos viejos 1.Si en un producto aparece el sĂmbolo de un contenedor de basura tachado, significa que ĂŠste se acoge a la Directiva 2002/96/CE. 2.Todos los aparatos elĂŠctricos o electrĂłnicos se deben desechar de forma distinta del servicio municipal de recogida de basura, a travĂŠs de puntos de recogida designados por el gobierno o las autoridades locales. 3.La correcta recogida y tratamiento de los dispositivos inservibles contribuye a evitar riesgos potenciales para el medio ambiente y la salud pĂşblica. 4.Para obtener mĂĄs informaciĂłn sobre cĂłmo deshacerse de sus aparatos elĂŠctricos y electrĂłnicos viejos, pĂłngase en contacto con su ayuntamiento, el servicio de recogida de basuras o el establecimiento donde adquiriĂł el producto. Danish SĂĽdan smider du dit gamle apparat ud 1.NĂĽr der er et tegn med et kryds over en skraldespand, betyder det, at produktet er omfattet af EU-direktiv 2002/96/EC. 2.Alle elektriske og elektroniske produkter skal smides ud et andet sted end gennem den kommunale affaldsordning ved hjĂŚlp af specielle indsamlingsfaciliteter, der er organiseret af staten 09 Regulatory Information cont. Portuguese Hungarian Slovak Polish Czech Croatian 10 Regulatory Information cont. Estonian Latvian Lithuanian 11
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Author :EXIF Metadata provided by EXIF.toolsCreate Date : 2010:04:06 17:31:40+09:00 Modify Date : 2010:04:06 17:32:15+09:00 Has XFA : No XMP Toolkit : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04 Format : application/pdf Creator : Title : Microsoft Word - G_User_s manual Creator Tool : PScript5.dll Version 5.2.2 Metadata Date : 2010:04:06 17:32:15+09:00 Producer : Acrobat Distiller 9.3.0 (Windows) Document ID : uuid:5abd4181-38bf-48d1-b5bf-e4b4f689b8a8 Instance ID : uuid:95b94d0e-c04e-4fda-81d0-f55ecdb8ca11 Page Count : 90