LG Electronics USA 42LG30DCUA LCD TV/MONITOR User Manual SAC307080 Edit1 en 6

LG Electronics USA LCD TV/MONITOR SAC307080 Edit1 en 6

Contents

User manual 1 of 2

Please read this manual carefully before operatingyour set. Retain it for future reference.Record model number and serial number of the set. See the label attached on the back cover and quote this  information to your dealer when you require service.LCD TV PLASMA TVOWNER’S MANUALLCD TV MODELS32LG30DC37LG30DC42LG30DC47LG50DC52LG50DCPLASMA TV MODELS42PG60CP/NO : SAC307080? (0805-REV00)www.lgcommercial.comAs an ENERGY STAR PartnerLG  Electronics  USA,  Inc.has  determined  that  thisproduct meets the ENERGYSTAR guidelines for energyefficiency.ENERGY STAR is a set of power-savingguidelines issued by the U.S.Environmental Protection Agency (EPA).
2WARNING  / CAUTIONWARNING / CAUTIONTo  prevent  fire  or  shock  hazards,  do  not  exposethis product to rain or moisture.FCC NOTICEClass B digital deviceThis equipment has been tested and found to complywith the limits for a Class B digital device, pursuant toPart  15 of the FCC Rules. These limits are designedto  provide  reasonable  protection  against  harmfulinterference in a residential installation. This equipmentgenerates, uses and can radiate radio frequency energyand, if not installed and used in accordance with theinstructions, may cause harmful interference to radiocommunications. However, there is no guarantee thatinterference will not occur in a particular installation.If this equipment does cause harmful interference toradio or television reception, which can be determinedby  turning  the  equipment  off  and  on,  the  user  isencouraged to try to correct the interference by oneor more of the following measures:- Reorient or relocate the receiving antenna.- Increase the separation between the equipment andreceiver.- Connect  the  equipment  to  an  outlet on  a  circuitdifferent from that to which the receiver is connected.- Consult  the  dealer  or  an  experienced  radio/TVtechnician for help.Any changes or modifications not expressly approvedby  the party  responsible for  compliance  could voidthe user’s authority to operate the equipment.CAUTIONDo  not attempt  to  modify  this  product  in  any  waywithout  written  authorization  from  LG  Electronics.Unauthorized  modification  could  void  the  user’sauthority to operate this product The  lightning  flash  with  arrowheadsymbol, within an equilateral triangle, isintended to alert the user to the presenceof  uninsulated  “dangerous  voltage”  within  theproduct’s  enclosure  that  may  be  of  sufficientmagnitude to constitute a risk of electric shock topersons.The exclamation point within an equilateraltriangle is intended to alert the user tothe  presence  of  important  operating  andmaintenance (servicing) instructions in the litera-ture accompanying the appliance.TO REDUCE THE RISK OF ELECTRIC SHOCKDO NOT REMOVE COVER (OR BACK). NOUSER SERVICEABLE PARTS INSIDE. REFER TOQUALIFIED SERVICE PERSONNEL.WARNING/CAUTIONTO REDUCE THE RISK OF FIRE AND ELECTRICSHOCK, DO NOT EXPOSE THIS PRODUCT TORAIN OR MOISTURE.NOTE TO CABLE/TV INSTALLERThis  reminder  is  provided  to  call  the  CATV  systeminstaller’s  attention  to  Article  820-40  of  the  NationalElectric Code (U.S.A.). The code provides guidelines forproper  grounding  and,  in  particular,  specifies  that  thecable ground shall be connected to the grounding systemof the building, as close to the point of the cable entryas practical.
3IMPORTANT SAFETY INSTRUCTIONSSAFETY INSTRUCTIONSRead these instructions.Keep these instructions.Heed all warnings.Follow all instructions.Do not use this apparatus near water.Clean only with dry cloth.Do not block any ventilation openings. Install inaccordance with the manufacturer’s instructions.Do  not  install  near any  heat  sources  such asradiators,  heat  registers,  stoves,  or  otherapparatus  (including  amplifiers)that  produceheat.Do not defeat the safety purpose of the polarizedor grounding-type  plug. A  polarized plug hastwo  blades  with  one wider  than  the  other.  Agrounding  type  plug  has  two  blades  and  athird grounding prong, The wide blade or thethird prong are provided for your safety. If theprovided  plug  does  not  fit  into  your  outlet,consult  an  electrician  for replacement  of  theobsolete outlet.Protect the power cord from being walked onor  pinched  particularly  at  plugs,  conveniencereceptacles, and the point where they exit fromthe apparatus.Only use attachments/accessories specified bythe manufacturer.Use only with the cart, stand, tripod, bracket,or table specified by the manufacturer, or soldwith the  apparatus. When a  cart is  used,  usecaution when moving the cart/apparatus com-bination to avoid injury from tip-over.Unplug  this  apparatus  during  lighting  stormsor when unused for long periods of time.Refer all servicing to qualified service personnel.Servicing  is  required  when  the  apparatus  hasbeen  damaged  in  any  way,  such  as  power-supply  cord  or  plug  is  damaged,  liquid  hasbeen  spilled  or  objects  have  fallen  into  theapparatus, the apparatus has been exposed torain or moisture, does not operate normally, orhas been dropped.12345768910
4SAFETY INSTRUCTIONSNever touch this apparatus or antenna duringa thunder or lighting storm. When  mounting a  TV  on the  wall,  make  surenot to install the TV by the hanging power andsignal cables on the back of the TV.Do not allow an impact shock or any objects tofall into the product, and do not drop onto thescreen with something.CAUTION concerning the Power Cord:It  is  recommend  that  appliances  be  placedupon  a  dedicated  circuit;  that  is,  a  singleoutlet circuit which powers only that applianceand  has  no  additional  outlets  or  branchcircuits.  Check  the  specification  page  of  thisowner's manual to be certain.Do  not  connect  too  many  appliances  to  thesame  AC  power outlet  as  this  could result  infire or electric shock.Do not overload wall outlets. Overloaded walloutlets, loose or damaged wall outlets, extensioncords,  frayed  power  cords,  or  damaged  orcracked wire insulation are dangerous.  Any ofthese conditions could result in electric shockor  fire.  Periodically  examine  the  cord  of  yourappliance, and if its appearance indicates damageor deterioration, unplug it, discontinue use ofthe appliance, and have the cord replaced withan  exact  replacement  part  by  an  authorizedservicer. Protect the power cord from physicalor  mechanical  abuse,  such  as  being  twisted,kinked,  pinched,  closed  in  a  door,  or  walkedupon.  Pay  particular  attention  to  plugs,  walloutlets, and the point where the cord exits theappliance. Do  not  make  the  TV  with  the  power  cordplugged  in.  Do  not  use  a  damaged  or  loosepower  cord.  Be  sure  do grasp  the  plug  whenunplugging the power cord. Do not pull on thepower cord to unplug the TV. WARNING - To reduce the risk of fire or electricalshock,  do  not  expose  this  product  to  rain,moisture or other liquids. Do not touch the TVwith  wet  hands.  Do  not  install  this  productnear  flammable  objects  such  as  gasoline  orcandles  or  expose  the  TV  to  direct  airconditioning. Do not expose to dripping or splashing and donot  place  objects  filled  with  liquids,  such  asvases, cups, etc. on or over the apparatus (e.g.on shelves above the unit).GGRROOUUNNDDIINNGGEnsure that you connect the earth ground wireto  prevent  possible  electric  shock.  (i.e.  a  TVwith a three-prong grounded AC plug must beconnected  to  a  three-prong  grounded  ACoutlet) If grounding methods are not possible,have  a  qualified  electrician  install  a  separatecircuit breaker.  Do not try to ground the unit by connecting itto  telephone  wires,  lightening  rods,  or  gaspipes.DDIISSCCOONNNNEECCTTIINNGG  DDEEVVIICCEE  FFRROOMM  MMAAIINNSSMains  plug  is  the  disconnecting  device.  Theplug must remain readily operable.Keep the product away from direct sunlight.1211141316171819Power SupplyShort-circuitBreaker15
5AANNTTEENNNNAASSOOuuttddoooorr  aanntteennnnaa  ggrroouunnddiinnggIf  an  outdoor  antenna  is  installed,  follow  theprecautions below. An outdoor antenna systemshould  not  be  located  in  the  vicinity  ofoverhead power lines or other electric light orpower circuits, or where it can come in contactwith  such  power  lines  or  circuits  as  death  orserious injury can occur.Be sure the antenna system is grounded so asto  provide  some  protection  against  voltagesurges and built-up static charges. Section  810  of  the  National  Electrical  Code(NEC) in the U.S.A. provides information withrespect to proper grounding of the mast andsupporting structure, grounding of the lead-inwire  to  an  antenna  discharge  unit,  size  ofgrounding  conductors,  location  of  antennadischarge  unit,  connection  to  groundingelectrodes and requirements for the groundingelectrode. AAnntteennnnaa  ggrroouunnddiinngg  aaccccoorrddiinngg  ttoo  tthheeNNaattiioonnaall  EElleeccttrriiccaall  CCooddee,,  AANNSSII//NNFFPPAA  7700CClleeaanniinnggWhen  cleaning,  unplug  the  power  cord  andscrub    gently  with  a  soft  cloth  to  preventscratching. Do not spray water or other liquidsdirectly on the TV as electric shock may occur.Do  not  clean  with chemicals  such  as alcohol,thinners or benzene.  MMoovviinnggMake  sure  the  product  is  turned  off,unplugged and all cables have been removed. Itmay take 2 or more people to carry larger TVs.Do not press against or put stress on the frontpanel of the TV. VVeennttiillaattiioonnInstall your TV where there is proper ventilation.Do  not  install  in  a  confined  space  such  as  abookcase. Do not cover the product with clothor other materials (e.g.) plastic while pluggedin. Do not install in excessively dusty places.   If you smell smoke or other odors coming fromthe  TV  or  hear  strange  sounds,  unplug  thepower cord contact an authorized service center.2220232420Antenna Lead in WireAntenna Discharge Unit(NEC Section 810-20)Grounding Conductor(NEC Section 810-21)Ground ClampsPower Service GroundingElectrode System (NECArt 250, Part H)Ground ClampElectric ServiceEquipmentNEC: National Electrical Code
6CONTENTSWARNING / CAUTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . 3FEATURE OF THIS TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8PREPARATIONAccessories  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Front Panel Information  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10Back Panel Information  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12Stand Instruction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14VESA Wall Mounting  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18Desktop Pedestal Installation  . . . . . . . . . . . . . . . . . . . . . . . . . . . 19Swivel Stand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19Cable Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20Attaching the TV to a Desk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22Securing the TV to the wall to prevent falling whenthe TV is used on a stand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23Antenna or Cable Connection . . . . . . . . . . . . . . . . . . . . . . . . . . 24EXTERNAL EQUIPMENT SETUPHD Receiver Setup   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25DVD Setup  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28VCR Setup  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31Other A/V Source Setup  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34PC Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35USB Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42Audio Out Connection  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43WATCHING TV / CHANNEL CONTROLRemote Control Functions  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44Turning On the TV  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46Channel Selection  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46Volume Adjustment  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46Quick Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47Initial Setting  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48On-Screen Menus Selection  . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50Channel Setup - Auto Scan (Auto Tuning) . . . . . . . . . . . . . . . . . . . . . . . . . . . 52- Add / Delete Channel (Manual Tuning) . . . . . . 53- Channel Editing  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54Input List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 Input Label  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 AV Mode  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57SIMPLINK  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58USBEntry Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60Photo List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61Music List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65PICTURE CONTROLPicture Size (Aspect Ratio) Control . . . . . . . . . . . . . . . . . . 68Preset Picture Settings- Picture Mode - Preset  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70- Color Tone - Preset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71Manual Picture Adjustment- Picture Mode - User Mode . . . . . . . . . . . . . . . . . . . . . . . . 72- Picture Mode - Expert Control  . . . . . . . . . . . . . . . . . . 73Picture Improvement Technology  . . . . . . . . . . . . . . . . . . . . . 74Advanced Control - Black (Darkness) Level . . . . . . . 75Advanced Control - Eye Care . . . . . . . . . . . . . . . . . . . . . . . . . . . 76Advanced Control - Real Cinema/Film Mode . . . . . 77Picture Reset  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78Power Indicator   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79Image Sticking Minimization (ISM) Method  . . . . . . 80Power Saving Picture Mode  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
7SOUND & LANGUAGE CONTROLAuto Volume Leveler (Auto Volume)  . . . . . . . . . . . . . . . . . 82Preset Sound Settings (Sound Mode)  . . . . . . . . . . . . . . 83Sound Setting Adjustment - User Mode  . . . . . . . . . . . 84Clear Voice  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85Balance  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86TV Speakers On/Off Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87Audio Reset   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88Stereo/SAP Broadcast Setup  . . . . . . . . . . . . . . . . . . . . . . . . . . . 89Audio Language  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90On-Screen Menus Language Selection . . . . . . . . . . . . . . 91Caption Mode- Analog Broadcasting System Captions  . . . . . . . 92- Digital Broadcasting System Captions . . . . . . . . 93- Caption Option   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94TIME SETTINGClock Setting- Auto Clock Setup   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95- Manual Clock Setup  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96Auto On/Off Time Setting   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97Sleep Timer Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98Auto Shut-off Setting  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99PARENTAL CONTROL / RATINGSSet Password & Lock System  . . . . . . . . . . . . . . . . . . . . . . . . . 10 0Channel Blocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103Movie & TV Rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 4Downloadable Rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 9External Input Blocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110Key lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111APPENDIXTroubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112Maintenance  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114Product Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115Programming the Remote Control   . . . . . . . . . . . . . . . . . . 116IR Codes    . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .119External Control Through RS-232C . . . . . . . . . . . . . . . . .121
8FEATURE OF THIS TVis a trademark of SRS Labs, Inc.TruSurround  XT  technology  is  incorporated  underlicense from SRS Labs, Inc.Manufactured under license from Dolby Laboratories.“Dolby“and the double-D symbol are trademarks ofDolby Laboratories. FOR LCD TV■If the TV feels cold to the touch, there may be a small “flicker” when it is turned on. This is normal, there isnothing wrong with TV.■Some minute dot defects may be visible on the screen, appearing as tiny red, green, or blue spots. However, theyhave no adverse effect on the monitor's performance.■Avoid touching the LCD screen or holding your finger(s) against it for long periods of time. Doing so may producesome temporary distortion effects on the screen.On Disposal (Only Hg lamp used LCD TV)The fluorescent lamp used in this product contains a small amount of mercury.  Do not dispose of this product withgeneral household waste. Disposal of this product must be carried out in accordance to the regulations of your localauthority.
PREPARATION9PREPARATIONACCESSORIESEnsure that the following accessories are included with your TV. If an accessory is missing, please contact thedealer where you purchased the TV. The accessories included may differ from the images below.OOppttiioonn  EExxttrraassFFoorr  LLCCDD  TTVV  mmooddeellssFFoorr  PPllaassmmaa  TTVV  mmooddeellss* Wipe spots on the exterior only withthe polishing cloth.* Do not wipe roughly when removingstain.  Excessive  pressure  may  causescratch or discoloration.Polishing Cloth(This feature is not availablefor all models.)Copyright© 2007 LGE,All Rights Reserved.D-sub 15 pin Cable1.5V 1.5VOwner’s Manual Power CordRemote Control,BatteriesINPUTFAVMUTETVSTBPOWERQ. MENUMENUAV MODERETURNENTERVOLCH1234567809FLASHBKPAGEDVDVCRCD ManualWhen using the VGA (D-sub 15 pincable)  PC  connection,  the  usermust  use  shielded  signal  interfacecables with ferrite cores to maintainstandards compliance.Bolts for stand assembly(Refer to P.16)(Only 32/37/42LG30DC)Protection CoverScrew for stand fixing(Refer to P.22)(Only 32LG30DC)x 4 x 4Cable Management Clip Protection CoverorCable HolderBolts for stand assembly(Refer to P.14)x 4
PREPARATION10PREPARATIONFRONT PANEL INFORMATION■Image shown may differ from your TV.■NOTE: If your TV has a protection tape attached, remove the tape.And then wipe the TV with a cloth (If a polishing cloth is included with your TV, use it).Plasma TV ModelsCHVOLMENUINPUT ENTERCHVOLMENUINPUT ENTERINPUTButtonMENUButtonENTERButtonVOLUME(-, +) ButtonsCHANNEL(EE,DD)ButtonsCHVOLMENUINPUT ENTERRemote Control SensorPOWER ButtonPower/Standby IndicatorIlluminates red in standby mode.Illuminates blue when the TV is switched on.
PREPARATION11LCD TV ModelsPOWER ButtonPower/Standby IndicatorIlluminates red in standby mode.Illuminates blue when the set is switched on.(Can be adjusted using PPoowweerr  IInnddiiccaattoorrinthe OPTION menu. GGpp..7799)CHVOLMENUINPUTENTERCHANNEL ( , ) ButtonsVOLUME (+, -) ButtonsENTER ButtonMENU ButtonINPUT ButtonIntelligent Sensor (Except 32/37/42LG30DC)Adjusts  picture  according  to  the  surroundingconditions Remote Control Sensor
PREPARATION12PREPARATIONBACK PANEL INFORMATIONPlasma TV Models■Image shown may differ from your TV.R(            )13AV IN 2L/MONORAUDIOVIDEOUSB INHDMI IN 4(            )9101RRGB INCOMPONENT INAUDIO(RGB/DVI)RGB(PC)ANTENNA/CABLE IN12RS-232C IN(CONTROL & SERVICE)VIDEOAUDIOVIDEOAUDIO OUTOPTICAL COAXIALMONO(            )AUDIOS-VIDEODIGITAL AUDIO OUTAV IN 1HDMI/DVI IN 321REMOTECONTROL IN134678295HDMI/DVI IN, HDMI INDigital Connection. Supports  HD  video  and  Digital  audio.  Doesn’tsupport 480i. Accepts  DVI  video  using  an  adapter  or  HDMI  toDVI cable (not included).COMPONENT INAnalog Connection. Supports HD. Uses a red, green, and blue cable for video & redand white for audio.RGB (PC)Analog PC Connection. Uses a D-sub 15 pin cable(VGA cable).AUDIO (RGB/DVI)1/8” headphone jack for analog PC audio input.REMOTE CONTROL IN PORTFor a wired remote control.RS-232C IN (CONTROL & SERVICE) PORTUsed by third party devices.ANTENNA/CABLE INConnect over-the air signals to this jack.Connect cable signals to this jack.DIGITAL AUDIO OUTDigital audio output for use with amps and hometheater systems. Includes an optical and/or coaxial connection.Note: In standby mode, these ports do not work.AUDIO OUTAnalog audio output for use with amps and hometheater systems.AV (Audio/Video) INAnalog composite connection. Supports standarddefinition video only (480i).S-VIDEOBetter  quality  than  standard  composition.Supports standard definition video only (480i).USB INPUTUsed for viewing photos and listening to MP3s.USB  SERVICE  ONLY  or  RS-232C  IN  (SERVICEONLY)Used for software updates.RJP INTERFACEPower Cord SocketFor operation with AC power. Caution: Never attempt to operate the TV on DCpower.12345691011121378
PREPARATION13LCD TV ModelsAV IN 2L/MONORAUDIOVIDEOUSB IN(            )RGB INCOMPONENT INAUDIO(RGB/DVI)RGB(PC)REMOTECONTROL INANTENNA/CABLE IN12RS-232C IN(CONTROL & SERVICE)VIDEOAUDIOOPTICAL COAXIALDIGITAL AUDIO OUTAUDIO OUTAV IN 1RHDMI/DVI IN 21VIDEOMONO(            )AUDIOS-VIDEO1346782995RGB INCOMPONENT INAUDIO(RGB/DVI)RGB(PC)REMOTECONTROL INRJPINTERFACEANTENNA/CABLE IN12RS-232C IN(CONTROL & SERVICE)VIDEOAUDIOOPTICALAUDIO OUTAV IN 1RVIDEOMONO(            )AUDIOS-VIDEO21HDMI/DVI INDIGITAL AUDIO OUT1347628510AV IN 2L/MONORAUDIOVIDEOUSBSERVUCE ONLY(            )9111247/52LG50DC32/37/42LG30DCR(            )139
PREPARATION14PREPARATIONSTAND INSTRUCTION■Image shown may differ from your TV.Carefully place the TV screen side down on acushioned  surface  to protect  the  screen  fromdamage.Assemble the TV as shown.Fix  the  4  bolts securely  using  the  holes  in  theback of the TV.123INSTALLATIONPlasma TV modelsGGWhen assembling the desk type stand, make surethe bolt is fully tightened. (If not tightened fully,the TV can tilt forward after the product installa-tion). Do not  over tighten.NOTE!
PREPARATION15DETACHMENTCarefully place the TV screen side down on acushioned  surface  to protect  the  screen  fromdamage.1Loose the bolts from TV.2Detach the stand from TV.3PROTECTION COVERAfter  removing  the  stand,  install  the  includedpprrootteeccttiioonn  ccoovveerrover the hole for the stand.Press  the  PPRROOTTEECCTTIIOONN  CCOOVVEERRinto  the  TVuntil you hear it click.
PREPARATION16PREPARATION■Image shown may differ from your TV.LCD TV modelsAssemble the parts of the SSTTAANNDD  BBOODDYYwith CCOOVVEERR  BBAASSEEof the TV.2Assemble the TV as shown.3Fix the 4 bolts securely using the holes in theback of the TV.4SSTTAANNDD  BBOODDYYCCOOVVEERR  BBAASSEECarefully place the TV screen side down on acushioned surface to protect the screen fromdamage.1INSTALLATION (Except 47/52LG50DC)GGWhen assembling the desk type stand, make surethe bolt is fully tightened. (If not tightened fully,the TV can tilt forward after the product installa-tion). Do not  over tighten.NOTE!
PREPARATION17DETACHMENTCarefully place the TV screen side down on acushioned  surface  to protect  the  screen  fromdamage.1Loose the bolts from TV.2Detach the stand from TV.3After  removing  the  stand,  install  the  includedpprrootteeccttiioonn  ccoovveerrover the hole for the stand.Press  the  PPRROOTTEECCTTIIOONN  CCOOVVEERRinto  the  TVuntil you hear it click.PROTECTION COVER
PREPARATION18PREPARATIONVESA WALL MOUNTINGInstall your wall mount on a solid wall perpendicular to the floor. When attaching to other building materials, pleasecontact your nearest dealer.If installed on a ceiling or slanted wall, it may fall and result in severe personal injury.We recommend that you use an LG brand wall mount when mounting the TV to a wall.LG recommends that wall mounting be performed by a qualified professional installer.GGDo not install your wall mount kit while your TV is turned on. It may result in personal injury due to electricshock.CAUTIONGGScrew length needed depends on the wall mountused. For further information, refer to the instruc-tions included with the mount.GGStandard dimensions for wall mount kits are shownin the table.GGWhen  purchasing  our  wall  mount  kit,  a  detailedinstallation  manual  and  all  parts  necessary  forassembly are provided.GGDo not use screws longer then the standard dimen-sion,  as  they may  cause damage  to the inside  tothe TV.GGFor wall mounts that do not comply with the VESAstandard  screw  specifications,  the  length  of  thescrews  may  differ  depending  on  their  specifica-tions.GGDo  not  use  screws  that  do  not  comply  with  theVESA standard screw specifications.Do not use fasten the screws too strongly, this maydamage the TV or cause the TV to a fall, leading topersonal injury. LG is not liable for these kinds ofaccidents.GGLG  is  not  liable  for  TV  damage  or  personal  injurywhen  a  non-VESA  or  non  specified  wall  mount  isused or the consumer fails to follow the TV installa-tion instructions.NOTE!AABBProduct Model VESA(A *B) Standard Screw Quantity32LG30DC37LG30DC42LG30DC47LG50DC52LG50DC42PG60C200 * 10 0200 * 200800 * 400400 * 400M4M6M6M64444LCD TVPLASMA TV
PREPARATION19DESKTOP PEDESTAL INSTALLATIONFor proper ventilation, allow a clearance of 4 inches on all four sides from the wall.■Image shown may differ from your TV.4 inches4 inches4 inches 4 inchesSWIVEL STANDAfter installing the TV, you can adjust the TV set manually to the left or right direction by 20 degrees to suityour viewing position.GGEnsure adequate ventilation by following the clearance recommendations.GGDo not mount near or above any type of heat source.CAUTION
PREPARATION20PREPARATIONCABLE MANAGEMENT■Image shown may differ from your TV.Plasma TV ModelConnect the cables as necessary.To connect additional equipment, see theEXTERNAL EQUIPMENT SETUP section.Install the CABLE MANAGEMENT CLIP asshown.If your TV has the CABLE HOLDER, install itas shown and bundle the cables.12GGDo not hold the CABLE MANAGEMENT CLIP when moving the TV.- If the TV is dropped, you may be injured or the product may be broken.NOTE!How to remove the CABLE MANAGEMENT CLIPGGFirst, press the cable management. Hold theCCAABBLLEE  MMAANNAAGGEEMMEENNTT  CCLLIIPPwith bothhands and pull it upward.CABLE MANAGEMENT CLIPCABLE HOLDER
PREPARATION21LCD TV ModelsConnect the cables as necessary.To connect additional equipment, see theEXTERNAL EQUIPMENT SETUP section.Install the CABLE MANAGEMENT CLIP asshown.Put the cables inside the CABLE MANAGE-MENT CLIP and snap it closed.CABLE MANAGEMENT CLIP123
PREPARATION22PREPARATIONATTACHING THE TV TO A DESK (Only 32/42LG30)The TV must be attached to a desk so it cannot be pulled in a forward/backward direction, potentially causinginjury or damaging the product. GGTo prevent TV from falling over, the TV should be securely attached to the floor/wall per installationinstructions. Tipping, shaking, or rocking the machine may cause injury.WARNING1-Screw(provided as parts of the product)DeskStand
PREPARATION23SECURING THE TV TO THE WALL TO PREVENT FALLINGWHEN THE TV IS USED ON A STANDWe recommend that you set up the TV close to a wall so it cannot fall over if pushed backwards. Additionally, we recommend that the TV be attached to a wall so it cannot be pulled in a forward direction,potentially causing injury or damaging the product. Caution: Please make sure that children don’t climb on or hang from the TV. ■Insert the eye-bolts (or TV brackets and bolts) to tighten the product to the wall as shown in the picture. *If your product has the bolts in the eye-bolts position before inserting the eye-bolts, loosen the bolts. * Insert the eye-bolts or TV brackets/bolts and tighten them securely in the upper holes.Secure the wall brackets with the bolts (sold separately) to the wall. Match the height of the bracket that ismounted on the wall to the holes in the product. Ensure the eye-bolts or brackets are tightened securely.■Use a  sturdy rope or  cord (sold  separately) to  tie the  product.  It  issafer to tie the rope so it becomes horizontal between the wall and theproduct.■You should purchase necessary components to prevent TV from falling off of the stand.■Image shown may differ from your TV.GGUse a platform or cabinet strong enough and large enough to support the size and weight of the TV.GGTo use the TV safely make sure that the height of the bracket on the wall and the one on the TV are the same.NOTE!
PREPARATION24PREPARATIONANTENNA OR CABLE CONNECTION1. Antenna (Analog or Digital)Wall Antenna Socket or Outdoor Antenna without a Cable BoxConnection.For optimum picture quality, adjust the antenna direction if needed.2. CableWallAntennaSocketOutdoorAntenna(VHF, UHF)Cable TVWall JackMulti-family Dwellings/Apartments(Connect to wall antenna socket)RF Coaxial Wire (75 ohm)RF Coaxial Wire (75 ohm)Single-family Dwellings /Houses(Connect to wall jack for outdoor antenna)Be careful not to bend the copper wirewhen connecting the antenna.Copper Wire■To improve the picture quality in a poor signal area, please purchase a signal amplifier and install properly.   ■If the antenna needs to be split for two TV’s, install a 2-Way Signal Splitter.■If the antenna is not installed properly, contact your dealer for assistance.ANTENNA/CABLE IN(            )RANTENNA/CABLE IN(            )R■To prevent damage do not connect to the power outlet until all connections are made between the devices.
EXTERNAL EQUIPMENT SETUP25EXTERNAL EQUIPMENT SETUPHD RECEIVER SETUPThis TV can receive digital over-the-air/digital cable signals without an external digital set-top box. However, ifyou do receive digital signals from a digital set-top box or other digital external device.Component Connection1. How to connectConnect the video outputs (Y, PB, PR)of the digital set-top box to the CCOOMMPPOONNEENNTT  IINN  VVIIDDEEOO  11jacks onthe TV. Match the jack colors (Y = green, PB= blue, andPR= red).Connect the audio output of the digital set-top box to the CCOOMMPPOONNEENNTT  IINN  AAUUDDIIOO  11jacks on the TV.212. How to use■Turn on the digital set-top box. (Refer to the owner’s manual for the digital set-top box. operation)■Select the CCoommppoonneenntt11input source on the TV usingthe IINNPPUUTTbutton on the remote control.■If connected to CCOOMMPPOONNEENNTT  IINN22input, select theCCoommppoonneenntt  22input source on the TV.■To prevent the equipment damage, never plug in any power cords until you have finished connecting all equipment.■Image shown may differ from your TV.Y, CB/PB, CR/PRSupported ResolutionsHorizontal  Vertical Frequency(KHz)Frequency(Hz)15.73 59.9415.73 60.0031.47 59.9431.50 60.0044.96 59.9445.00 60.0033.72 59.9433.75 60.0026.97 23.97627.00 24.0033.71 29.9733.75 30.0067.432 59.9467.50 60.00Resolution 720x480i720x480p1280x720p1920x1080i1920x1080pSignal480i480p720p108 0 i108 0 pComponentYesYesYesYesYesHDMINoYesYesYesYesRGB INAUDIO(RGB/DVI)RGB(PC)REMOTECONTROL IN(COAV IN 1DVI IN COMPONENT IN12VIDEOLYPBPRRAUDIOY L RPBPR12
EXTERNAL EQUIPMENT SETUP26EXTERNAL EQUIPMENT SETUPHDMI ConnectionLCD  TV:  Connect  the  digital  set-top  box  toHHDDMMII//DDVVII  IINN11or 22jack on the TV.Plasma  TV:  Connect  the  digital  set-top  box  toHHDDMMII//DDVVII  IINN11, 22, 33, or 44  jack on the TV.No separate audio connection is necessary.HDMI supports both audio and video.1. How to connect2. How to use■Turn on the digital set-top box. (Refer to the owner’s manual for the digital set-top box.)■LCD TV: Select the HHDDMMII11or HHDDMMII22  input source on theTV using the IINNPPUUTTbutton on the remote control.Plasma TV: Select the HHDDMMII11, HHDDMMII22, HHDDMMII33, or HHDDMMII44input source on the TV using the IINNPPUUTTbutton on theremote control.21HDMI-DTVHorizontal  Vertical Frequency(KHz)Frequency(Hz)31.47 59.9431.50 60.0044.96 59.9445.00 60.0033.72 59.9433.75 60.0026.97 23.97627.00 24.0033.71 29.9733.75 30.0067.432 59.93967.50 60.00Resolution 720x480p1280x720p1920x1080i1920x1080pRGB INCOMPONENT A(RGRGB(PC)12VIDEOYPBPRHDMI/DVI IN 21HDMI-DTV OUTPUTLCD TVRGB INCOMPONRGB(PC)VIDEOYPBPR23(            )HDMI/DVI IN 1HDMI-DTV OUTPUT(            )11Plasma TV
EXTERNAL EQUIPMENT SETUP27DVI to HDMI Connection1. How to connect2. How to use■Turn on the digital set-top box. (Refer to the owner’s manu-al for the digital set-top box.)■LCD TV: Select the HHDDMMII11or HHDDMMII22input source on the TVusing the IINNPPUUTTbutton on the remote control.Plasma TV: Select the HHDDMMII11,HHDDMMII22,orHHDDMMII33inputsource on the TV using the IINNPPUUTTbutton on the remotecontrol.21LCD TV: Connect the DVI output of the digital set-topbox to the HHDDMMII//DDVVII  IINN  11or 22jack on the TV.Plasma TV: Connect the DVI output of the digital set-top box to the HHDDMMII//DDVVII  IINN  11, 22, or 33jack on theTV.Connect  the  PC  audio  output  to  the  AAUUDDIIOO((RRGGBB//DDVVII))jack on the TV.GGA DVI to HDMI cable or adapter is required for this con-nection. DVI doesn't support audio, so a separate audioconnection is necessary.NOTE!RGB INCOMPONENT INAUDIO(RGB/DVI)RGB(PC)REMOCONTRO12VIDEOLYPBPRRAUDIOHDMI/DVI IN 21L RDVI-DTV OUTPUT12LCD TV(            )RGB INCOMPONENT INAUDIO(RGB/DVI)RGB(PC)REMOTECONTROL IN(COVIDEOLYPBPRRAUDIOAV IN 12321(            )HDMI/DVI IN 1L RDVI-DTV OUTPUT1Plasma TV2
EXTERNAL EQUIPMENT SETUP28EXTERNAL EQUIPMENT SETUPDVD SETUPComponent ConnectionComponent Input portsTo get better picture quality, connect a DVD player to the component input ports as shown below.Component ports on the TVYPBPRVideo output ports on DVD playerYYYYPBB-YCbPbPRR-YCrPrConnect the video outputs (Y,  PB, PR)of the DVD to theCCOOMMPPOONNEENNTT  IINN  VVIIDDEEOO11jacks on the TV.Match the jack colors (Y = green, PB= blue, and PR= red).Connect the audio outputs of the DVD to the CCOOMMPPOONNEENNTT  IINN  AAUUDDIIOO11jacks on the TV.1. How to connect2. How to use■Turn on the DVD player, insert a DVD.■Select the CCoommppoonneenntt11input source on the TV usingthe IINNPPUUTTbutton on the remote control.■If connected to CCOOMMPPOONNEENNTT  IINN  22input, select theCCoommppoonneenntt  22input source on the TV.■Refer to the DVD player's manual for operating instructions.21RGB INAUDIO(RGB/DVI)RGB(PC)REMOTECONTROL (CAV IN 1DMI/DVI IN COMPONENT IN12VIDEOLYPBPRRAUDIOY L RPBPR1 2
EXTERNAL EQUIPMENT SETUP29S-Video ConnectionT INAUDIOGB/DVI)REMOTECONTROL INANTENNA/CABLE INRS-232C IN(CONTROL & SERVICE)L RAUDIOOPTICAL COAXIALDIGITAL AUDIO OUTAUDIO OUTAV IN 1VIDEO LR(MONO)AUDIOS-VIDEOL RS-VIDEOAUDIO12Connect the S-VIDEO  output  of  the  DVD to  theSS--VVIIDDEEOOinput on the TV.Connect the audio outputs of the DVD to the AAUUDDIIOOinput jacks on the TV.1. How to connect2. How to use■Turn on the DVD player, insert a DVD.■Select the AAVV11input source on the TV using the IINNPPUUTTbutton on the remote control.  ■Refer to the DVD player's manual for operating instructions.21
EXTERNAL EQUIPMENT SETUP30EXTERNAL EQUIPMENT SETUPHDMI ConnectionLCD TV: Connect the HDMI output of the DVD to theHHDDMMII//DDVVII  IINN11or 22jack on the TV.Plasma TV: Connect the HDMI output of the DVD tothe HHDDMMII//DDVVII  IINN11, 22, 33, or 44jack on the TV. No separate audio connection is necessary.HDMI supports both audio and video.1. How to connect2. How to use■LCD TV: Select the HHDDMMII11or HHDDMMII22input source on theTV using the IINNPPUUTTbutton on the remote control.Plasma TV: Select the HHDDMMII11, HHDDMMII22, HHDDMMII33, or HHDDMMII44input  source  on  the  TV  using  the  IINNPPUUTTbutton  on  theremote control.■Refer to the DVD player's manual for operating instructions.21COMPONENT INAUDI(RGB/DRGB(PC)12VIDEOLYPBPRAHDMI/DVI IN 21HDMI-DVD OUTPUT1LCD TVRGB INCOMPONENT(RRGB(PC)VIDEOYPBPR2321(            )HDMI/DVI IN 1HDMI-DVD OUTPUT1Plasma TV
EXTERNAL EQUIPMENT SETUP31VCR SETUPAntenna Connection■To avoid picture noise (interference), leave an adequate distance between the VCR and TV.■Use the ISM feature in the Option menu to avoid having a fixed image remain on the screen for a long periodof time (Plasma TV models only).  If the 4:3 picture format is used; the fixed images on the sides of the screenmay remain visible on the screen. This phenomenon is common to all TVs and is not covered by warranty.ANTENNA/CABLE INE)COAXIALUDIO OUTAUDIO OUTEO L R(MONO)AUDIOL RS-VIDEO VIDEOOUTPUTSWITCHANT INANT OUTWall JackAntenna12Connect the RF antenna out socket of theVCR to the AANNTTEENNNNAA//CCAABBLLEE  IINNsock-et on the TV.Connect  the  antenna  cable  to  the  RFantenna in socket of the VCR.1. How to connect2. How to use■Set VCR output switch to 3 or 4 and thentune TV to the same channel number.■Insert a video tape into the VCR and pressPLAY on the VCR. (Refer to the VCR owner’smanual.)21
EXTERNAL EQUIPMENT SETUP32EXTERNAL EQUIPMENT SETUPComposite (RCA) ConnectionGGIf you have a mono VCR, connect the audio cable fromthe VCR to the AAUUDDIIOO  LL//MMOONNOOjack of the TV.NOTE!NT INAUDIO(RGB/DVI)REMOTECONTROL INANTENNA/CABLE INRS-232C IN(CONTROL & SERVICE)L RAUDIOOPTICAL COAXIALDIGITAL AUDIO OUTAUDIO OUTAV IN 1VIDEO L R(MONO)AUDIOS-VIDEOL RS-VIDEO VIDEOOUTPUTSWITCHANT INANT OUT1Connect the AAUUDDIIOO/VVIIDDEEOOjacks between TV andVCR. Match the jack colors (Video = yellow, Audio Left= white, and Audio Right = red)1. How to connect2. How to use■Insert a video tape into the VCR and press PLAY on the VCR.(Refer to the VCR owner’s manual.)■Select the AAVV11input source on the TV using the IINNPPUUTTbutton on the remote control.■If connected to AAVV  IINN22, select AAVV22input source on the TV.1
EXTERNAL EQUIPMENT SETUP33GGDo not connect to both Video and S-Video at the sametime. In the event that you connect both Video and theS-Video cables, only the S-Video will work.CAUTIONGGS-Video provides better quality than composite. Use itwhen available.NOTE!S-Video ConnectionENT INAUDIO(RGB/DVI)REMOTECONTROL INANTENNACABLE INRS-232C IN(CONTROL & SERVICE)LRRAUDIOOPTICAL COAXIALDIGITAL AUDIO OUTAUDIO OUTAV IN 1VIDEO LR(MONO)AUDIOS-VIDEOL RS-VIDEO VIDEOOUTPUTSWITCHANT INANT OUT12Connect the  S-VIDEO output  of  the VCR to theSS--VVIIDDEEOO  input on the TV.Connect the audio outputs of the VCR to the AAUUDDIIOOinput jacks on the TV.1. How to connect2. How to use■Insert a video tape into the VCR and press PLAY on the VCR.(Refer to the VCR owner’s manual.)■Select the AAVV11input source on the TV using the IINNPPUUTTbutton on the remote control.21
EXTERNAL EQUIPMENT SETUP34EXTERNAL EQUIPMENT SETUPOTHER A/V SOURCE SETUPL/MONORAUDIOVIDEOUSB INL RVIDEOCamcorderVideo Game SetConnect  the  AAUUDDIIOO/VVIIDDEEOOjacksbetween  TV  and  external  equipment.Match the jack colors.(Video = yellow, Audio Left = white, andAudio Right = red)1. How to connect2. How to use■Select the  AAVV22input source on the TV usingthe IINNPPUUTTbutton on the remote control.■If connected to AAVV  IINN11input, select the AAVV11input source on the TV.■Operate the corresponding external equipment.11
EXTERNAL EQUIPMENT SETUP35PC SETUPThis TV provides Plug and Play capability, meaning that the PC adjusts automatically to the TV's settings. VGA (D-Sub 15 pin) ConnectionConnect the VGA output of the PC to the RRGGBB((PPCC))  jack on the TV.Connect the PC audio output to the  AAUUDDIIOO((RRGGBB//DDVVII))jack on the TV.1. How to connect2. How to use■Turn on the PC and the TV.■Select the RRGGBB--PPCCinput source on the TV using theIINNPPUUTTbutton on the remote control.21COMPONENT INREMOTECONTROL I12(COVIDEOLYPBPRRAUDIOMI/DVI IN RGB INAUDIO(RGB/DVI)RGB(PC)RGB OUTPUT AUDIO1 2
EXTERNAL EQUIPMENT SETUP36EXTERNAL EQUIPMENT SETUPLCD TVPlasma TVDVI to HDMI ConnectionLCD  TV:  Connect  the  DVI  output  of  the  PC  to  theHHDDMMII//DDVVII  IINN  11or 22  jack on the TV.Plasma TV: Connect the DVI output of the PC to theHHDDMMII//DDVVII  IINN  11, 22, or 33  jack on the TV.Connect  the  PC  audio  output  to  the  AAUUDDIIOO((RRGGBB//DDVVII))  jack on the TV.1. How to connect2. How to use■Turn on the PC and the TV.■LCD TV: Select the HHDDMMII11or HHDDMMII22  input source on the TVusing the IINNPPUUTTbutton on the remote control.Plasma TV: Select the HHDDMMII11,HHDDMMII22,orHHDDMMII33input sourceon the TV using the IINNPPUUTTbutton on the remote control.21COMPONENT INRECON12VIDEOLYPBPRRAUDIOHDMI/DVI IN 21RGB INAUDIO(RGB/DVI)RGB(PC)DVI-PC OUTPUT AUDIO1 2RGB INCOMPONENT INAUDIO(RGB/DVI)RGB(PC)REMOTCONTROVIDEOLYPBPRRAUDIO2321(            )HDMI/DVI IN 1DVI-PC OUTPUT AUDIO12
EXTERNAL EQUIPMENT SETUP37GG32/37/42LG30DC,  42PG60C:  To  get  the  thebest picture quality, adjust the PC graphics card to1360x768.GG47/52LG50DC: To get the the best picture quali-ty, adjust the PC graphics card to 1920x1080.GGDepending on the graphics card, DOS mode maynot work if a HDMI to DVI Cable is in use.GGIn  PC mode,  there  may  be  noise  associated  withthe resolution, vertical pattern, contrast or bright-ness. If noise is present, change the PC output toanother  resolution,  change  the  refresh  rate  toanother rate or adjust the brightness and contraston the PICTURE menu until the picture is clear.GGAvoid  keeping  a  fixed  image  on  the  screen  for  along period of time. The fixed image could becomepermanently imprinted on the screen.GGThe synchronization input form for Horizontal andVertical frequencies is separate.GGDepending on the graphics card, some resolutionsettings may not allow the image to be positionedon the screen properly.GGIf there are overscan in HDMI-PC 1920x1080,change aspect ratio to JJuusstt  ssccaann.NOTES!Supported Display Specifications (RGB-PC, HDMI-PC)Horizontal  Vertical Frequency(KHz)Frequency(Hz)31.469  70.0831.469 70.0831.469 59.9437.879 60.3148.363 60.0047.776 59.8747.720 59.79947.130 59.65Resolution 720x4001360x768640x350640x480800x6001024x7681280x7681366x768For 32/37/42LG30DCFor 47/52LG50DC, Plasma TV* Only RGB-PC mode Resolution 640x350Horizontal  Vertical Frequency(KHz)Frequency(Hz)31.468  70.0931.469 70.0831.469 59.9437.500 75.0037.861 72.8035.156 56.2537.879 60.3146.875 75.0048.077 72.1848.363 60.0056.476 70.0660.023 75.0247.776 59.8760.289 74.89363.981 60.0279.976 75.02547.712 60.01575.00 60.0066.587 59.93467.5 60.0066.587 59.934* Only RGB-PC mode 720x4001360x768640x480800x6001024x7681280x10241600x1200LCD TV1920x1080Plasma TV1920x1080RGB-PCHDMI-PC1280x768
EXTERNAL EQUIPMENT SETUP38EXTERNAL EQUIPMENT SETUPScreen Setup for PC modeSelecting ResolutionYou can choose the resolution in RGB-PC mode. The PPoossiittiioonn, PPhhaassee, and SSiizzeecan also be adjusted.Select PPIICCTTUURREE.Select SSccrreeeenn  ((RRGGBB--PPCC)).Select RReessoolluuttiioonn.Select the desired resolution.1024 x 7681280 x 7681360 x 7681366 x 768Auto config.ResolutionGPositionSizePhaseResetSCREENMovePrev.MENU1MENU342ENTERENTERENTER5ENTEREnterMovePICTUREE• Brightness 50• Sharpness 60• Color 60• Tint 0• Advanced Control• ResetScreen (RGB-PC)TruMotion DemoRG Only for32/37/42LG30DC
EXTERNAL EQUIPMENT SETUP39Auto ConfigureAutomatically adjusts picture position and minimizes image instability. After adjustment, if the image is stillnot correct, try using the manual settings or a different resolution or refresh rate on the PC.Select SSccrreeeenn  ((RRGGBB--PPCC)).Select AAuuttoo  ccoonnffiigg...Auto config. GResolutionPositionSizePhaseResetSCREENMovePrev.MENUTo Set32ENTERENTERSelect YYeess.4ENTERStart Auto Configuration.5ENTERSelect PPIICCTTUURREE.1MENU• If  the  position  of  the  image  is  still  notcorrect, try Auto adjustment again.• If  picture  needs  to  be  adjusted  againafter  Auto  adjustment  in  RGB-PC,  youcan  adjust  the  PPoossiittiioonn,  SSiizzee  orPPhhaassee.EnterMovePICTUREE• Brightness 50• Sharpness 60• Color 60• Tint 0• Advanced Control• ResetScreen (RGB-PC)TruMotion DemoRGYes No
EXTERNAL EQUIPMENT SETUP40EXTERNAL EQUIPMENT SETUPAdjustment for screen Position, Size, and PhaseIf the picture is not clear after auto adjustment and especially if characters are still trembling, adjust the picturephase manually.This feature operates only in RGB-PC mode.Select PPoossiittiioonn, SSiizzee, or PPhhaassee.Make appropriate adjustments.Auto config.ResolutionPositionGSizePhaseResetGFDESCREENMovePrev.MENU3ENTER4ENTER■PPoossiittiioonn: This function is to adjust pic-ture  to  left/right  and  up/down  as  youprefer. ■SSiizzee:  This  function  is  to  minimize  anyvertical  bars  or  stripes  visible  on  thescreen  background.  And  the  horizontalscreen size will also change.■PPhhaassee:  This  function  allows  you  toremove any horizontal noise and clear orsharpen the image of characters.Select PPIICCTTUURREE.Select SSccrreeeenn  ((RRGGBB--PPCC)).1MENU2ENTER5ENTEREnterMovePICTUREE• Brightness 50• Sharpness 60• Color 60• Tint 0• Advanced Control• ResetScreen (RGB-PC)TruMotion DemoRG
EXTERNAL EQUIPMENT SETUP41Screen Reset (Reset to original factory values)Returns PPoossiittiioonn, SSiizzee, and PPhhaasseeto the default factory settings.This feature operates only in RGB-PC mode.Auto config.PositionResolutionSizePhaseResetGSCREENMovePrev.MENUTo SetSelect RReesseett.3ENTERSelect PPIICCTTUURREE.Select SSccrreeeenn  ((RRGGBB--PPCC)).1MENU2ENTERSelect YYeess.4ENTER5ENTEREnterMovePICTUREE• Brightness 50• Sharpness 60• Color 60• Tint 0• Advanced Control• ResetScreen (RGB-PC)TruMotion DemoRGYes No
EXTERNAL EQUIPMENT SETUP42EXTERNAL EQUIPMENT SETUPUSB CONNECTION(Except 32/37/42LG30DC)AV IN 2L/MONORAUDIOVIDEOUSB INConnect the USB device to the UUSSBB  IINNjack on the sideof TV. 1. How to connect12. How to use■After connecting the UUSSBB  IINNjack, you use the USB func-tion. (GGpp..6600)1ori.e)
EXTERNAL EQUIPMENT SETUP43AUDIO OUT CONNECTIONSend the TV’s audio to external audio equipment via the Audio Output port.RS-232C IN(CONTROL & SERVICE)RAUDIOAUDIO OUTAV IN 1VIDEO L R(MONO)AUDIOS-VIDEOL RAUDIO1NUDIOB/DVI)REMOTECONTROL INANTENNA/CABLE INRS-232C IN(CONTROL & SERVICE)L RAUDIOOPTICAL COAXIALDIGITAL AUDIO OUTAUDIO OUTAV IN 1VIDEO L R(MONO)AUDIOS-VIDEO12GGWhen connecting with external audio equipments, such asamplifiers or speakers, you can turn the TV speakers off inthe menu.  (GG  pp..8877)NOTE!GDo not look into the optical output port. Looking at thelaser beam may damage your vision.GGBlock the SPDIF out (optical/coaxial) about the contentswith ACP(Audio Copy Protection) function.CAUTIONConnect one end of the optical or coaxial cable to theTV’s OOPPTTIICCAALL  or CCOOAAXXIIAALL(Except 32/37/42LG30DC)port of DDIIGGIITTAALL  AAUUDDIIOO  OOUUTT.Connect the other end of the optical or coaxial cable tothe digital audio input on the audio equipment.Set the “TV Speaker option - Off” in the AUDIO menu. (GGpp..8877). See the external audio equipment instruction manu-al for operation.1. How to connect231Connect audio outputs to the TV’s AAUUDDIIOO  OOUUTTjacks.Set the “TV Speaker option - Off” in the AUDIO menu.(GGpp..8877). See the external audio equipment instructionmanual for operation.1. How to connect21AnalogDigital
WATCHING TV / CHANNEL CONTROL44REMOTE CONTROL FUNCTIONSWATCHING TV / CHANNEL CONTROLWhen using the remote control, aim it at the remote control sensor on the TV.INPUTFAVMUTETVSTBPOWERQ. MENU MENUAV MODERETURNENTERVOL CH1234567809FLASHBKPAGEDVDVCRTV/STB/DVD/VCRPOWERQ.MENUMENUINPUTVOLUME UP/DOWNFAVMUTECHANNELUP/DOWNPAGEUP/DOWN— (DASH)FLASHBKSelect the remote operating mode: TV, STB, DVD, or VCR. Turns your TV or any other programmed equipment on oroff, depending on the mode.Select the desired quick menu source. GGpp..4477Displays the main menu.Clear all on-screen displays and return to TV viewing fromany menu.External input modes rotate in regular sequence.Increase/decrease the sound level.Scroll through the programmed Favorite channels. GGpp..4477Switch the sound on or off. GGpp..4466Select available channels.Move from one full set of screen information to the next one.Used to enter a program number for multiple program channels such as 2-1, 2-2, etc.Tune to the last channel viewed.Control video cassette recorders or DVD players.Control USB menu (PHOTO LIST and MUSIC LIST.)Control the SIMPLINK compatible devices.NUMBER buttonVCR/DVD, USB,SIMPLINK  Control buttons
WATCHING TV / CHANNEL CONTROL45Installing Batteries■Open the battery compartment cover on the back side and installthe batteries matching correct polarity (+with +,-with -).■Install two 1.5V AAA batteries. Don’t mix old or used batteries withnew ones.■Close cover.THUMBSTICK(Up/Down/LeftRight/ENTER)RETURNSIMPLINKAV MODENavigate the on-screen menus and adjust the system settings to your preference.Allows the user to move return one step in an interactive application or other user interactionfunction.See a list of AV devices connected to TV.When you toggle this button, the SIMPLINK menu appears at the screen. GGpp..5588--5599It helps you select and set images and sounds. GGpp..5577
WATCHING TV / CHANNEL CONTROL46WATCHING TV / CHANNEL CONTROLTURNING ON THE TVNOTE!GGIf you intend to be away on vacation, disconnect the power plug from the wall power outlet.First, connect power cord correctly. At this moment, the TV switches to standby mode.■In standby mode to turn TV on, press the , IINNPPUUTT,CCHH  ((DDEEor  ))button  on  the  TV  or  press  the  PPOOWWEERR,  IINNPPUUTT,  CCHH((or  )),  NNuummbbeerr((00~99))button on the remote control.Select the viewing source by using the IINNPPUUTTbutton on the remote control.■This TV is programmed to remember which power state it was last set to,even if the power cord is out.When finished using the TV, press the PPOOWWEERRbutton on the remote control.The TV reverts to standby mode.123Press the CCHH((or  ))or NNUUMMBBEERRbuttons to select a channel number.1VOLUME ADJUSTMENTCHANNEL SELECTIONPress the VVOOLL((++  or --))button to adjust the volume.If you want to switch the sound off, press the MMUUTTEEbutton. You can cancel the Mute function by pressing the MMUUTTEEor VVOOLL((++  or --))button.Adjust the volume to suit your personal preference.123
WATCHING TV / CHANNEL CONTROL47QUICK MENUDisplay each menu.Make appropriate adjustments.■AAssppeecctt  RRaattiioo: Selects your desired picture format. ■PPoowweerr  SSaavviinngg  (Plasma TV Only): Adjusts screenbrightness to reduce the power consumption of theTV.■BBaacckklliigghhtt  (LCD TV  Only): Adjust the brightnessof LCD panel to control the brightness of the screen.■CClleeaarr  VVooiiccee: By differentiating the human soundrange  from  others,  it  helps  make  human  voicessound better.■PPiiccttuurree  MMooddee: Selects the factory preset picturedepend on the viewing environment.■SSoouunndd  MMooddee: Selects the factory preset sound fortype of program.■CCaappttiioonn: Select on or off.■MMuullttii  AAuuddiioo: Changes the audio language (Digitalsignal).SSAAPP: Selects MTS sound (Analog signal).■SSlleeeepp  TTiimmeerr:  Select  the  amount  of  time  beforeyour TV turns off automatically.■DDeell//AAdddd//FFaavv: Select channel you want to add/deleteor add the channel to the Favorite List.■UUSSBB  EEjjeecctt:  Select  “USB  Eject”  in  order  to  ejectUSB device.Your TV's OSD (On Screen Display) may differ slightly from what is shown in this manual.Q.Menu (Quick Menu) is a menu of features which users might use frequently.1Q. MENU2LCD TVQ.Menu3FF16:9     GGVividOffStandardOffEnglishOffAddEjectAspect RatioBacklightClear VoicePicture ModeSound ModeCaptionMulti AudioSleep TimerDel/Add/FavUSB EjectCHPlasma TVQ.MenuClose Close3FF16:9     GGVividOffStandardOffEnglishOffAddEjectAspect RatioPower SavingClear VoicePicture ModeSound ModeCaptionMulti AudioSleep TimerDel/Add/FavUSB EjectCH3Q. MENUReturn to TV viewing.Except 32/37/42LG30DC
WATCHING TV / CHANNEL CONTROL48WATCHING TV / CHANNEL CONTROLINITIAL SETTINGThis Function guides the user to easily set the essential items for viewing the TV for the first time when pur-chasing the TV. If will be displayed on the screen when turning the TV on for the first time. It can also be acti-vated from the user menus.Select HHoommeeMode.12ENTERSelect AAuuttooor MMaannuuaall.Select desired time option.13ENTER2YearCurrent Time Setting2007Month 11Date 15Hour 5 PMMinute 52Time Zone EasternDaylight SavingOffFF            Auto GGExitEnterRETURNStep2. Time SettingSelecting the environment.Choose the setting mode you want.In StoreHomeExitEnterRETURNStep1. Mode SettingStep1. Mode settingStep2. Time setting■Default selection is “HHoommee”. We recommend setting the TV to “HHoommee” mode for the best picture in yourhome environment.■“IInn--ssttoorree” Mode is only intended for use in retail environments. Customers can adjust the “PPiiccttuurreemenu -PPiiccttuurree  mmooddee” manually while  inspecting the  TV, but  the  TV will  automatically return to preset in-storemode after 5 minutes.!
WATCHING TV / CHANNEL CONTROL49Select OOSSDD  LLaanngguuaaggee  SSeettttiinnggorAAuuddiioo  LLaanngguuaaggee  SSeettttiinngg.Start AAuuttoo  TTuunniinngg.Select your desired language.13ENTER1ENTER2Auto Tuning can change channel map.Do you want to start Auto Tuning?EnterExitEnterRETURNStep4. Auto TuningExitEnterRETURNStep3. Option Setting1. OSD Language SettingFFEnglish GG2. Audio Language Setting FrenchStep3. Option settingStep4. Auto Tuning■ You can also adjust IInniittiiaall  SSeettttiinnggin the OOPPTTIIOONN  menu.NOTE!
WATCHING TV / CHANNEL CONTROL50WATCHING TV / CHANNEL CONTROLON-SCREEN MENUS SELECTIONYour TV's OSD (On Screen Display) may differ slightly from that shown in this manual.NOTE!GGIISSMM  MMeetthhoodd, PPoowweerr  SSaavviinngg: OnlyPPllaassmmaa  TTVV.GGBBaacckklliigghhtt,,  PPoowweerr  IInnddiiccaattoorr: OnlyLLCCDD  TTVV.Display each menu.Select a menu item.Enter to the pop up menu.1MENU32ENTERENTERReturn to TV viewing.4MENUEnterMoveAuto TuningManual TuningChannel EditCHANNELCHANNELOPTIONPICTURELOCKAUDIOINPUTTIMEUSBEnterMoveAspect Ratio   : 16:9Picture Mode  : Standard• Backlight 80 • Contrast 90• Brightness 50• Sharpness 60• Color 60• Tint 0PICTUREEEnterMoveAuto Volume : OffClear Voice : OnBalance 0Sound Mode : Standard• SRS TruSurround XT:Off• Treble 50• Bass 50• ResetAUDIOELREnterMoveClock :Feb/21/2008  2:10 AMOff Time : OffOn Time : OffSleep Timer : OffAuto Sleep : OffTIMEEnterMovePHOTO LISTMUSIC LISTUSBEnterMoveAntennaCableAV1AV2Component1Component2RGB-PCHDMI1INPUTEEnterMoveLock System            : OffSet PasswordBlock ChannelMovie RatingTV Rating-ChildrenTV Rating-GeneralDownloadable RatingInput BlockLOCKLock System            : OffSet PasswordBlock ChannelTV Rating-EnglishTV Rating-FrenchDownloadable RatingInput BlockEnterMoveLanguage : EnglishInput LabelSIMPLINK : OnKey Lock : OffCaption : OffISM Method : NormalPower Saving : Level 0Set ID : 1OPTIONFor USA For CanadaEAll models (Except 32/37/42LG30DC)RG
WATCHING TV / CHANNEL CONTROL51Only for 32/37/42LG30DCDisplay each menu.Select a menu item.Enter to the pop up menu.1MENU32ENTERENTERReturn to TV viewing.4MENUEnterMoveAuto TuningManual TuningChannel EditCHANNELCHANNELTIMEPICTUREOPTIONAUDIOLOCKEnterMoveAspect Ratio   : 16:9Picture Mode  : Standard• Backlight 80 • Contrast 90• Brightness 50• Sharpness 60• Color 60• Tint 0PICTUREEEnterMoveAuto Volume : OffClear Voice : OnBalance 0Sound Mode : Standard• SRS TruSurround XT:Off• Treble 50• Bass 50• ResetAUDIOELREnterMoveClock :Feb/21/2008  2:10 AMOff Time : OffOn Time : OffSleep Timer : OffAuto Sleep : OffTIMEEnterMoveLock System            : OffSet PasswordBlock ChannelMovie RatingTV Rating-ChildrenTV Rating-GeneralDownloadable RatingInput BlockLOCKEnterMoveLanguage : EnglishInput LabelSIMPLINK : OnKey Lock : OffCaption : OffSet ID : 1Power IndicatorInitial Setting : HomeOPTIONLock System            : OffSet PasswordBlock ChannelTV Rating-EnglishTV Rating-FrenchDownloadable RatingInput BlockFor USA For CanadaRG
WATCHING TV / CHANNEL CONTROL52WATCHING TV / CHANNEL CONTROLCHANNEL SETUPAuto Scan (Auto Tuning)Automatically finds all channels available through antenna or cable inputs, and stores them in memory on thechannel list. Run Auto Tuning again after any Antenna/Cable connection changes. Select CCHHAANNNNEELL.Select AAuuttoo  TTuunniinngg.Select YYeess.Run AAuuttoo  ttuunniinngg.EnterMoveCHANNELEnterMoveCHANNEL1MENU32ENTERENTER4ENTERAuto TuningManual TuningChannel EditAuto TuningManual TuningChannel EditPress ‘Yes’ button to beginauto tuning.YesNo■A password is required to gain access toAuto Tuning menu if the Lock System isturned on.5RETURNReturn to the previous menu.MENUReturn to TV viewing.
WATCHING TV / CHANNEL CONTROL53Select CCHHAANNNNEELL.1MENU2ENTERIf selecting DTV or CADTV input signal, you can view the on-screen signal strength monitor to see the qualityof the signal being received.Add/Delete Channel (Manual Tuning)EnterMoveCHANNELEnterMoveCHANNELChannelSelect channel type and RF-channel number.FF              DTVGG2CloseDeleteAuto TuningManual TuningChannel EditDTV 2-1Bad              Normal            GoodSelect MMaannuuaall  TTuunniinngg.Select DDTTVV, TTVV, CCAADDTTVV, or CCAATTVV.Select channel you want to addor delete.3ENTER4Select AAdddd  or DDeelleettee.5ENTERAuto TuningManual TuningChannel Edit■A password is required to gain access toManual Tuning menu if the Lock Systemis turned on.6RETURNReturn to the previous menu.MENUReturn to TV viewing.
WATCHING TV / CHANNEL CONTROL54WATCHING TV / CHANNEL CONTROLCHANNEL SETUPSelect a channel.Select channel you want to add ordelete.3ENTER4ENTERA custom list can be created by toggling each channel on or off with ENTER button. The channels in the CustomList are displayed in black and the channels deleted from the Custom List are displayed in gray. Once a channel is highlighted you can add or delete the channel by referring to the small window at the top-right corner of the screen.Channel EditingEnterMoveCHANNELAuto TuningManual TuningChannel EditSelect CCHHAANNNNEELL.1MENU2ENTERSelect CChhaannnneell  EEddiitt.RETURNReturn to TV viewing.Return to the previous menu.5MENUAdd/Delete Move PageCHMove PreviousMENU ExitRETURN
WATCHING TV / CHANNEL CONTROL55INPUT LISTOnly these input signals which are connected to a TV can be activated and selected.Select the desired input source.■You  can  also  select  the  desired  input  source  in  the  IINNPPUUTT  menu(Except 32/37/42LG30DC).1INPUTAntenna Cable AV1 AV2HDMI2 HDMI1 RGB-PC Component2 Component1Antenna Cable AV1 AV2 Component1ENTER■AAnntteennnnaa: Select it to watch over-the-air broadcasts.■CCaabbllee: Select it to watch cable and digital cable.■AAVV: Select them to watch a VCR or other external equipment.■CCoommppoonneenntt: Select them to watch DVD or a Digital set-top box.■RRGGBB--PPCC: Select it to view PC input.■HHDDMMII: Select them to watch high definition devices.Antenna Cable AV1 AV2 Component1Input LabelQ.MENU ExitRETURNSelect  a  desired  input  source  (exceptAAnntteennnnaaor  CCaabbllee).  Then,  you  can  selectyour desired Input Label with using Q. MENUbutton. GGpp..6600Disconnected inputs are inactive (grayed out)ie)LCD TVAntenna Cable AV1 AV2 Component1HDMI4 HDMI3 HDMI2 HDMI1 RGB-PCComponent2Plasma TV
WATCHING TV / CHANNEL CONTROL56WATCHING TV / CHANNEL CONTROLINPUT LABELYou can set a label for each input source when it's not in use.EnterMoveOPTIONLanguage : EnglishInput LabelSIMPLINK : OnKey Lock : OffCaption : OffISM Method : NormalPower Saving : Level 0Set ID : 1EESelect OOPPTTIIOONN.Select IInnppuutt  LLaabbeell.Select the label.1MENU2ENTERSelect the source.3ENTER45RETURNReturn to the previous menu.MENUReturn to TV viewing.With using OPTION menuSelect the source.Select the label.1INPUT2Q. MENU3RETURNReturn to the previous menu.MENUReturn to TV viewing.With using INPUT button■When new external device is connected, this popup menu is displayed automatically. If selecting YYeess, you can select input source that you want to appreciate.■But, when selecting “SSIIMMPPLLIINNKK- OOnn”, popup menu for HDMI input will not be displayed.NoYes!New external device is connected.Do you want to enjoy this?!Select input source that you want to appreciate.AV1AV2Component1AV1 FFGGAV2Component1HDMI1RGB-PCComponent2HDMI2CloseAV1 FFGGAV2Component1HDMI1RGB-PCComponent2HDMI2HDMI3HDMI4ClosePlasma TVLCD TV
WATCHING TV / CHANNEL CONTROL57AV MODEYou can select the optimal images and sounds.1AV MODE2Off CinemaGame SportPress the AAVV  MMOODDEEbutton repeatedly to select the desired source.ENTER■If  you  select  “CCiinneemmaa” in  AV  mode,CCiinneemmaa  will be selected both for “PIC-TURE menu - Picture Mode” and “AUDIOmenu - Sound Mode” respectively.■If  you  select  “OOffff”  in  AV  mode,  the“PPiiccttuurree  MMooddee”  and  “SSoouunndd  MMooddee”return to previous selected value.
WATCHING TV / CHANNEL CONTROL58WATCHING TV / CHANNEL CONTROLThis function operates only with devices with the  logo.The TV might not function properly when using it with other products with HDMI-CEC function.This allows you to control and play other AV devices connected with HDMI cable without additional cables andsettings.To start using SIMPLINK, turn it on in the user menus.EnterMoveOPTIONSelect OOPPTTIIOONN.Select SSIIMMPPLLIINNKK.Select OOnn  or OOffff.EnterMoveOPTIONE1MENU32ENTERENTERLanguage : EnglishInput LabelSIMPLINK : OnKey Lock : OffCaption : OffISM Method : NormalPower Saving : Level 0Set ID : 1Language : EnglishInput LabelSIMPLINK : OnKey Lock : OffCaption : OffISM Method : NormalPower Saving : Level 0Set ID : 1OffOnNOTE!GGConnect the HDMI/DVI IN or HDMI IN terminal of the TV to the rear terminal (HDMI terminal) of theSIMPLINK device with the HDMI cable. GGWhen you switch the Input source with the INPUT button on the remote control, the SIMPLINK devicewill stop.GGWhen you select a device with home theater functionality, the sound output automatically switches tothe home theater speakers.GGIf a connected SIMPLINK home theater system doesn't play the audio from the TV, connect the DIGITALAUDIO OUT terminal on the back of the TV to the DIGITAL AUDIO IN terminal on the back of the SIM-PLINK device with an OPTICAL cable.E4RETURNReturn to the previous menu.MENUReturn to TV viewing.
WATCHING TV / CHANNEL CONTROL59■DDiirreecctt  PPllaayy::  After connecting AV devices to the TV, you can directly control the devices and play media with-out additional settings.■SSeelleecctt  AAVV  ddeevviiccee::  Enables you to select one of the AV devices connected to TV.■DDiisscc  ppllaayybbaacckk::  Control connected AV devices by pressing the  , ENTER, G, A, ll  ll, FF and GG buttons. ■PPoowweerr  ooffff  aallll  ddeevviicceess::  When you power off the TV, all connected devices are turned off.■SSwwiittcchh  aauuddiioo--oouutt::  Offers an easy way to switch audio-out.■SSyynncc  PPoowweerr  oonn::  When you play the connected AV device, TV will automatically turn on.(A device, which is connected to the TV through a HDMI cable but does not support SIMPLINK, does not providethis function)Note: To operate SIMPLINK, an HDMI cable over Version 1.2 with *CEC function should be used. (*CEC: ConsumerElectronics Control).SIMPLINK Menu TTVV  vviieewwiinngg:  Switch  to  the  previous  TVchannel regardless of the current mode.DDIISSCC  ppllaayybbaacckk:  Select  and  play  discs.When multiple discs are available, the titlesof  discs  are  conveniently displayed at  thebottom of the screen.VVCCRR  ppllaayybbaacckk:  Control  the  connectedVCR.HHDDDD  RReeccoorrddiinnggss  ppllaayybbaacckk:  Controlrecordings stored in HDD.AAuuddiioo  OOuutt  ttoo  HHoommee  TThheeaatteerr  ssppeeaakk--eerr//AAuuddiioo  OOuutt  ttoo  TTVV:  Select  HomeTheater  speaker  or  TV  speaker  for  AudioOut.SIMPLINK Functions12345GGWhen no device is connected(displayed in gray)GGSelected  DeviceGGWhen a device is connected(displayed in bright color)12345Display SSIIMMPPLLIINNKK  menu.Select the desired device.Control connected AV devices.1TV32ENTERENTER
USB60USBENTRY MODESWhen you connect a USB device, this screen is displayed automatically.In USB device, you can not add a new folder or delete the existing folder.Precautions when using the USB deviceGGOnly a USB storage device is recognizable. GGIf the USB storage device is connected through aUSB hub, the device is not recognizable.GGA USB storage device using an automatic recogni-tion program may not be recognized.GGA  USB  storage  device  which  uses  its  own  drivermay not be recognized.GGIn case of a card reader, up to four memory cardsare concurrently recognizable.GGThe  recognition  speed  of  a  USB  storage  devicemay depend on each device.GGPlease do not turn off the TV or unplug the USBdevice when the connected USB storage device isworking.  When such device is suddenly separatedor unplugged, the stored files or the USB storagedevice may be damaged. GGPlease  do  not  connect  the  USB  storage  devicewhich was artificially maneuvered on the PC.  Thedevice may cause the product to malfunction orfail to be played.  Never forget to use only a USBstorage  device  which  has  normal  music  files  orimage files.GGPlease use  only a  USB  storage device which wasformatted as a FAT or NTFS file system providedwith the Windows operating system.  In case of astorage device formatted as a different utility pro-gram which is not supported by Windows, it maynot be recognized.GGPlease  connect  power  to  a  USB  storage  devicewhich  requires  an  external power supply.   If not,the device may not be recognized.GGPlease connect a USB storage device with cable isoffered by USB maker.  If connected with cable isnot offered by USB maker or an excessively longcable, the device may not be recognized.GGSome USB storage devices may not be supportedor operated smoothly.GGFile alignment  method  of  USB  storage  device  issimilar to Window XP and filename can recognizeup to 100 English characters.GGPlease  backup  important  files  because  data  onUSB device may be damaged. Data management isconsumer's responsibility and as a result, the man-ufacturer does not cover data damage.When removing the USB deviceConnect the USB device to the UUSSBB  IINNjacks on the side of TV. 3Select PPHHOOTTOO  LLIISSTT  or MMUUSSIICCLLIISSTT1USB INPHOTO LIST MUSIC LISTSelect UUSSBB  EEjjeecctt.Select the UUSSBB  EEjjeeccttmenu before removing theUSB device.2ENTER1Q. MENU2ENTER* Except 32/37/42LG30DC■It doesn’t support USB HDD■This TV supports JPG and MP3.

Navigation menu