LG Electronics USA 42LG30UA LCD TV/MONITOR User Manual PQ SAC30708020 Edit1 en

LG Electronics USA LCD TV/MONITOR PQ SAC30708020 Edit1 en

Contents

User manual I

Download: LG Electronics USA 42LG30UA LCD TV/MONITOR User Manual PQ SAC30708020 Edit1 en
Mirror Download [FCC.gov]LG Electronics USA 42LG30UA LCD TV/MONITOR User Manual PQ SAC30708020 Edit1 en
Document ID882107
Application IDkWNcE9PeZzOx7qJEgbZkIg==
Document DescriptionUser manual I
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize264.41kB (3305082 bits)
Date Submitted2007-12-20 00:00:00
Date Available2007-12-20 00:00:00
Creation Date2007-12-20 10:21:52
Producing SoftwareAcrobat Distiller 4.0.5 for Macintosh
Document Lastmod2007-12-20 10:21:57
Document TitlePQ_SAC30708020-Edit1-en
Document Creator3.3: LaserWriter 8 Z1-8.7.1
Document Author: sun

LCD TV PLASMA TV
OWNER’S MANUAL
ENERGY STAR is a set of power-saving
guidelines issued by the U.S.
Environmental Protection Agency(EPA).
As an ENERGY STAR
Partner LGE U. S. A.,Inc.
has determined that this
product meets the
ENERGY STAR guidelines
for energy efficiency.
LCD TV MODEL
PLASMA TV MODELS
26LG30
32LG30
37LG30
42LG30
37LG50
42LG50
47LG50
52LG50
42PG20
50PG20
32LG60
37LG60
42LG60
47LG60
52LG60
32LG70
42LG70
47LG70
52LG70
42PG20C
50PG20C
50PG60F
60PG60F
Please read this manual carefully before operating
your set.
Retain it for future reference.
Record model number and serial number of the set.
See the label attached on the back cover and quote
this information to your dealer
when you require service.
P/NO : SAC30708020 (0711-REV00)
www.lgusa.com / www.lg.ca / www.lgcommercial.com
WARNING / CAUTION
WARNING / CAUTION
To prevent fire or shock hazards, do not expose
this product to rain or moisture.
TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK). NO
USER SERVICEABLE PARTS INSIDE. REFER TO
QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead
symbol, within an equilateral triangle, is
intended to alert the user to the presence
of uninsulated “dangerous voltage” within the
product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to
persons.
The exclamation point within an equilateral
triangle is intended to alert the user to
the presence of important operating and
maintenance (servicing) instructions in the literature accompanying the appliance.
WARNING/CAUTION
TO REDUCE THE RISK OF FIRE AND ELECTRIC
SHOCK, DO NOT EXPOSE THIS PRODUCT TO
RAIN OR MOISTURE.
NOTE TO CABLE/TV INSTALLER
This reminder is provided to call the CATV system
installer’s attention to Article 820-40 of the National
Electric Code (U.S.A.). The code provides guidelines for
proper grounding and, in particular, specifies that the
cable ground shall be connected to the grounding system
of the building, as close to the point of the cable entry
as practical.
FCC NOTICE
Class B digital device
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful
interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference to
radio or television reception, which can be determined
by turning the equipment off and on, the user is
encouraged to try to correct the interference by one
or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and
receiver.
- Connect the equipment to an outlet on a circuit
different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV
technician for help.
Any changes or modifications not expressly approved
by the party responsible for compliance could void
the user’s authority to operate the equipment.
CAUTION
Do not attempt to modify this product in any way
without written authorization from LG Electronics.
Unauthorized modification could void the user’s
authority to operate this product
SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
Important safety instructions shall be provided with each apparatus. This information shall be given in a separate
booklet or sheet, or be located before any operating instructions in an instruction for installation for use and
supplied with the apparatus.
This information shall be given in a language acceptable to the country where the apparatus is intended to be used.
The important safety instructions shall be entitled “Important Safety Instructions”. The following safety
instructions shall be included where applicable, and, when used, shall be verbatim as follows. Additional safety
information may be included by adding statements after the end of the following safety instruction list. At the
manufacturer’s option, a picture or drawing that illustrates the intent of a specific safety instruction may be
placed immediately adjacent to that safety instruction:
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not defeat the safety purpose of the polarized
or grounding-type plug. A polarized plug has
two blades with one wider than the other. A
grounding type plug has two blades and a third
grounding prong, The wide blade or the third
prong are provided for your safety. If the provided
plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.
Protect the power cord from being walked on
or pinched particularly at plugs, convenience
receptacles, and the point where they exit from
the apparatus.
Only use attachments/accessories specified by
the manufacturer.
Unplug this apparatus when unused for long
periods of time.
Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
Do not install near any heat sources such as
radiators, heat registers, stoves, or other apparatus
(including amplifiers)that produce heat.
When mounting a TV it on the wall, make sure
not to install TV by hanging power and signal
cables on the back of the TV.
10
Use only with the cart, stand, tripod, bracket,
or table specified by the manufacturer, or sold
with the apparatus. When a cart is used, use
caution when moving the cart/apparatus
combination to avoid injury from tip-over.
11
Never touch this apparatus or antenna during
a thunder or lighting storm.
12
Do not allow a impact shock or any objects to
fall into the product, and do not drop onto the
screen with something.
13
Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has
been damaged in any way, such as power-supply
cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus,
the apparatus has exposed to rain or moisture,
does not operate normally, or has been
dropped.
14
CAUTION concerning the Power Cord :
Most appliances recommend they be placed
upon a dedicated circuit; that is, a single outlet
circuit which powers only that appliance and
has no additional outlets or branch circuits.
Check the specification page of this owner's
manual to be certain.
Do not overload wall outlets. Overloaded wall
outlets, loose or damaged wall outlets, extension
cords, frayed power cords, or damaged or
cracked wire insulation are dangerous. Any of
these conditions could result in electric shock
or fire. Periodically examine the cord of your
appliance, and if its appearance indicates damage or deterioration, unplug it, discontinue use
of the appliance, and have the cord replaced
with an exact replacement part by an authorized
servicer. Protect the power cord from physical
or mechanical abuse, such as being twisted,
kinked, pinched, closed in a door, or walked
upon. Pay particular attention to plugs, wall
outlets, and the point where the cord exits the
appliance.
15
Outdoor use marking :
WARNING - To reduce the risk of fire or electric shock, do not expose this appliance to rain
or moisture.
16
Wet Location Marking : Apparatus shall not be
exposed to dripping or splashing and no
objects filled with liquids, such as vases, shall
be placed on or over apparatus.
17
GROUNDING
Ensure that you connect the earth ground wire
to prevent possible electric shock. If grounding
methods are not possible, have a qualified
electrician install a separate circuit breaker.
Do not try to ground the unit by connecting it
to telephone wires, lightening rods, or gas pipes.
Power
Supply
Short-circuit
Breaker
18
DISCONNECTING DEVICE FROM MAINS
Mains plug is the disconnecting device. The
plug must remain readily operable.
CONTENTS
WARNING / CAUTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . 2
FEATURE OF THIS TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
PREPARATION
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Front Panel Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Back Panel Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Stand Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Back Cover for Wire Arrangement . . . . . . . . . . . . . . . . . . . . . 16
Desktop Pedestal Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
VESA Wall Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Swivel Stand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Not Using the Desk-Type Stand . . . . . . . . . . . . . . . . . . . . . . . . 19
Attaching the TV to a Desk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
How to join the TV Assemble to the wall to protect
the TV tumbling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Antenna or Cable Connection . . . . . . . . . . . . . . . . . . . . . . . . . . 21
EXTERNAL EQUIPMENT SETUP
HD Receiver Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
DVD Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
VCR Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Other A/V Source Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
PC Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
USB In Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Audio Out Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
WATCHING TV / CHANNEL CONTROL
Remote Control Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Turning On TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Channel Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Volume Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Quick Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Installation Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
On-Screen Menus Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Channel Setup
- Auto Scan (Auto Tuning) . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
- Add / Delete Channel (Manual Tuning) . . . . . . 49
- Channel Editing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Input List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Input Label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
AV Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
SimpLink . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
USB
Entry Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Photo List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Music List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
PICTURE CONTROL
Picture Size (Aspect Ratio) Control . . . . . . . . . . . . . . . . . . 64
Preset Picture Settings
- Picture Mode - Preset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
- Color Tone - Preset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Manual Picture Adjustment
- Picture Mode - User Mode . . . . . . . . . . . . . . . . . . . . . . . . 68
- Color Tone - User Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Picture Improvement Technology . . . . . . . . . . . . . . . . . . . . . 70
Advanced - Black (Darkness) Level . . . . . . . . . . . . . . . . . . . 71
Advanced - Eye Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Advanced - Film Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Advanced - TruMotion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
TruMotion Demo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Picture Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Power Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Image Sticking Minimization (ISM) Method . . . . . . . 78
Power Saving Picture Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
SOUND & LANGUAGE CONTROL
APPENDIX
Auto Volume Leveller (Auto Volume) . . . . . . . . . . . . . . . . 80
Preset Sound Setting (Sound Mode) . . . . . . . . . . . . . . . . 81
Sound Setting Adjustment - User Mode . . . . . . . . . . . 82
Clear Voice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Balance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
TV Speakers On/Off Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Audio Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
Stereo/SAP Broadcasts Setup . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Audio Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
On-Screen Menus Language Selection . . . . . . . . . . . . . 89
Caption Mode
- Analog Broadcasting System Captions . . . . . . . 90
- Digital Broadcasting System Captions . . . . . . . . 91
- Caption Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
Product Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
Programming the Remote Control . . . . . . . . . . . . . . . . . . 116
IR Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .119
External Control Through RS-232C . . . . . . . . . . . . . . . . .121
TIME SETTING
Clock Setting
- Auto Clock Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
- Manual Clock Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Auto On/Off Timer Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
Sleep Timer Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Auto Shut-off Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
PARENTAL CONTROL / RATINGS
Set Password & Lock System . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
Channel Blocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
Movie & TV Rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
Downloadable Rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
External Input Blocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
Key lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
FEATURE OF THIS TV
is a trademark of SRS Labs, Inc.
TruSurround XT technology is incorporated under
license from SRS Labs, Inc.
LG TV with this logo can play MP3 music from a MP3
player, such as iPOD, and JPEG images from a digital
camera through the USB device.
With HDMI CEC support of LG’s audio/video device
connected to the HDMI (high-definition multimedia
interface), LG TV with this logo works easily with one
remote control.
It has three HDMI ports that connect audio and video
devices with one cable and produces the highest quality digital images and sound.
Manufactured under license from Dolby Laboratories.
“Dolby “and the double-D symbol are trademarks of
Dolby Laboratories.
High-definition television. High-resolution digital television broadcast and playback system composed of
roughly a million or more pixels, 16:9 aspect-ratio
screens, and AC3 digital audio. A subset of digital
television, HDTV formats include 1080i and 720p resolutions.
LG's own special digital image generator, consisting of
a full digital image processor, six different main picture
quality factors.
It has 2 HDMI ports that connect audio and video
devices with one cable and produces the highest
quality digital images and sound.
FOR LCD TV
■
If the TV feels cold to the touch, there may be a small “flicker” when it is turned on. This is normal, there is
nothing wrong with TV.
Some minute dot defects may be visible on the screen, appearing as tiny red, green, or blue spots. However, they
have no adverse effect on the monitor's performance.
■ Avoid touching the LCD screen or holding your finger(s) against it for long periods of time. Doing so may produce
some temporary distortion effects on the screen.
■
On Disposal
a. The fluorescent lamp used in this product contains a small amount of mercury.
b. Do not dispose of this product with general household waste.
c. Disposal of this product must be carried out in accordance to the regulations of your local authority.
PREPARATION
ACCESSORIES
TV
PO
ST
Q.
MEN B
MEN
RE
TU
RN
AV
VO
FA
CH
MU
TE
ER
DV
MO
DE
IN CR
PU
EN
TE
PREPARATION
Ensure that the following accessories are included with your product. If an accessory is missing, please contact
the dealer where you purchased the product.
User must use shielded signal interface cables (D-sub 15 pin cable) with ferrite cores to maintain standard
compliance for the product.
The accessories can be different from the figures shown here.
FLASH
BK
1.5V 1.5V
Copyright© 2007 LGE,
All Rights Reserved.
Owner’s Manual
Remote Control,
Batteries
CD Manual
Power Cord
75ohm Round Cable
* Slightly wipe stained spot on the exterior only with the
polishing cloth for the product exterior if there is stain or
fingerprint on surface of the exterior.
or
Polishing Cloth
Protection Cover
(Refer to P.19)
(This accessories can be different from the figures
shown here depending on your models.)
(This feature is not available
for all models.)
* Do not wipe roughly when removing stain. Please be cautions of that excessive pressure may cause scratch or discoloration.
Option Extras
For Plasma TV models
Cable Management Clip
D-sub 15 pin Cable
For LCD TV models
x4
x4
Bolts for stand
assembly
(Refer to P.15)
(Only 26/32/37/42LG30,
37/42LG50)
x3
Screw for stand
fixing
(Refer to P.19)
(Only 26/32LG30,
32LG50)
x4
Bolts for stand
assembly
(Refer to P.15)
Cable Management
Clip
(Only 32/37/42/47/52LG60)
PREPARATION
FRONT PANEL INFORMATION
PREPARATION
■
Image shown may differ from your TV
■
NOTE: If your product has a protection tape attached, remove the tape.
And then wipe the product with a cloth (If a polishing cloth is included with your product, use it).
Plasma TV Model
Remote Control Sensor
POWER Button
Power/Standby Indicator
Illuminates red in standby mode.
Illuminates green when the set is
switched on.
INPUT
MENU
INPUT
VOL
ENTER
MENU
INPUT
MENU
VOL
ENTER
INPUT
Button
ENTER
MENU
Button
CH
VOL
CH
CH
ENTER
Button
VOLUME
(-, +) Buttons
CHANNEL
(E,D)Buttons
LCD TV Model
CH
Intelligent Sensor (Except **LG30)
Adjusts picture according to the
surrounding conditions
VOL
CHANNEL (D,E)
Buttons
PREPARATION
26/32/37/42/47/52LG30/50/70
VOLUME (+, -)
Buttons
ENTER
Power/Standby Indicator
Illuminates red in standby mode.
Illuminates blue when the set is switched on.
Note: You can adjust P o w e r I n d i c a t o r in
the OPTION menu.
ENTER Button
MENU
MENU Button
INPUT
INPUT Button
POWER Button
32/37/42/47/52LG60
CH
VOL
Intelligent Sensor
Adjusts picture according to the
surrounding conditions.
CHANNEL (D,E)
Buttons
VOLUME (+, -)
Buttons
ENTER Button
POWER Button
Remote Control Sensor
Power/Standby Indicator
Illuminates red in standby mode.
Illuminates white when the TV is switched on.
Note: You can adjust P o w e r I n d i c a t o r in the
OPTION menu.
ENTER
MENU Button
MENU
INPUT Button
INPUT
PREPARATION
BACK PANEL INFORMATION
■
Image shown may differ from your TV
Plasma TV Model
HDMI IN 4
USB IN
PREPARATION
10
VIDEO L/MONO AUDIO R
11
AV IN 2
ANTENNA/
CABLE IN
RGB IN
HDMI/DVI IN
AUDIO
(RGB/DVI)
RGB(PC)
REMOTE
CONTROL IN
DIGITAL AUDIO OUT
OPTICAL COAXIAL
RS-232C IN
(CONTROL & SERVICE)
COMPONENT IN
AUDIO
VIDEO
10
S-VIDEO
AUDIO
VIDEO
(MONO)
AV IN 1
AUDIO OUT
PREPARATION
HDMI/DVI IN, HDMI IN
Connect a HDMI signal to HDMI port.
Or DVI (VIDEO) signal to the HDMI port with a
DVI to HDMI cable.
COMPONENT IN
Connect a component video/audio device to these
jacks.
RGB (PC)
Connect the output from a PC.
AUDIO (RGB/DVI)
Connect the audio from a PC.
REMOTE CONTROL PORT
Connect your wired remote control.
RS-232C IN (CONTROL & SERVICE) PORT
Connect to the RS-232C port on a PC.
ANTENNA/CABLE IN
Connect over-the air signals to this jack.
Connect cable signals to this jack.
DIGITAL AUDIO OUT
Connect digital audio to various types of equipment.
Note: In standby mode, these ports do not work.
AUDIO OUT
Connect analog audio to various types of equipment.
AV (Audio/Video) IN
Connect audio/video output from an external
device to these jacks.
S-VIDEO
Connect S-Video out from an S-VIDEO device.
10
USB INPUT
11
Power Cord Socket
For operation with AC power.
Caution: Never attempt to operate the TV on DC
power.
11
PREPARATION
■
Image shown may differ from your TV
HDMI IN 3
32/37/42/47/52LG60
10
VIDEO L/MONO AUDIO R
PREPARATION
26/32/37/42/47/52LG30/50
USB
SERVUCE ONLY
LCD TV Model
11
AV IN 2
11
37/42/47/52LG50
ANTENNA/
CABLE IN
RGB IN
DIGITAL AUDIO OUT
AUDIO
(RGB/DVI)
RGB(PC)
REMOTE
CONTROL IN
OPTICAL
COAXIAL
HDMI/DVI IN
RS-232C IN
(CONTROL & SERVICE)
AUDIO OUT
1 (DVI)
AUDIO
VIDEO
S-VIDEO VIDEO
COMPONENT IN
(MONO)
AUDIO
AV IN 1
26/32/37/42LG30
ANTENNA/
CABLE IN
AUDIO
(RGB/DVI)
REMOTE
CONTROL IN
HDMI IN
RS-232C IN
(CONTROL & SERVICE)
AUDIO
VIDEO
HDMI/DVI IN
COMPONENT IN
12
DIGITAL
AUDIO OUT
OPTICAL
S-VIDEO VIDEO
AUDIO OUT
(MONO)
AUDIO
AV IN 1
RGB IN
RGB(PC)
USB
HDMI IN 4 R SERVUCE ONLY
10
PREPARATION
VIDEO L/MONO AUDIO R
32/42/47/52LG70
AV IN 2
11
RGB IN
DIGITAL AUDIO OUT
AUDIO
(RGB/DVI)
RGB(PC)
REMOTE
CONTROL IN
OPTICAL
COAXIAL
RS-232C IN
(CONTROL & SERVICE)
AUDIO OUT
AUDIO
VIDEO
S-VIDEO VIDEO
COMPONENT IN
(MONO
AUDIO
AV IN 1
1 (DVI)
HDMI/DVI IN
ANTENNA/
CABLE IN
HDMI/DVI IN, HDMI IN
Connect a HDMI signal to HDMI port.
Or DVI (VIDEO) signal to the HDMI port with a
DVI to HDMI cable.
COMPONENT IN
Connect a component video/audio device to these
jacks.
RGB (PC)
Connect the output from a PC.
AUDIO (RGB/DVI)
Connect the audio from a PC.
REMOTE CONTROL PORT
Connect your wired remote control.
RS-232C IN (CONTROL & SERVICE) PORT
Connect to the RS-232C port on a PC.
ANTENNA/CABLE IN
Connect over-the air signals to this jack.
Connect cable signals to this jack.
DIGITAL AUDIO OUT
Connect digital audio to various types of equipment.
Note: In standby mode, these ports do not work.
AUDIO OUT
Connect analog audio to various types of equipment.
AV (Audio/Video) IN
Connect audio/video output from an external
device to these jacks.
S-VIDEO
Connect S-Video out from an S-VIDEO device.
10
USB INPUT
11
Power Cord Socket
For operation with AC power.
Caution: Never attempt to operate the TV on DC
power.
13
PREPARATION
STAND INSTALLATION
■
PREPARATION
14
Image shown may differ from your TV
Plasma TV Model
42PG20
Carefully place the TV screen side down on a
cushioned surface to protect the screen from
damage.
Assemble the TV as shown.
Fix the 4 bolts securely using the holes in the
back of the TV
LCD TV Model
Only 26/32/37/42LG30, 37/42LG50
32/37/42/47/52LG60
Carefully place the TV screen side down on a
cushioned surface to protect the screen from
damage.
Carefully place the TV screen side down on a
cushioned surface to protect the screen from
damage.
Assemble the parts of the S T A N D B O D Y
with C O V E R B A S E of the TV.
Assemble the parts of the S T A N D B O D Y
with C O V E R B A S E of the TV.
PREPARATION
STAND BODY
STAND BODY
COVER BASE
COVER BASE
Assemble the TV as shown.
Fix the 4 bolts securely using the holes in the
back of the TV
Assemble the TV as shown.
Fix the 4 bolts securely using the holes in the
back of the TV
15
PREPARATION
BACK COVER FOR WIRE ARRANGEMENT
■
Image shown may differ from your TV.
Plasma TV Model
PREPARATION
42/50PG10/20
50/60PG60F
Connect the cables as necessary.
To connect an additional equipment, see the
EXTERNAL EQUIPMENT SETUP section.
Install the CABLE MANAGEMENT CLIP as
shown and manage the cable.
CABLE MANAGEMENT CLIP
How to remove the
CABLE MANAGEMENT CLIP
Hold the CABLE MANAGEMENT CLIP with
both hands and pull it backward.
Separate CABLE MANAGEMENT CLIP
from TV by pressing two latches.
! NOTE
16
Do not hold the CABLE MANAGEMENT
CLIP when moving the TV.
- If the TV is dropped, you may be injured
or the product may be broken.
Arrange the cables as shown.
LCD TV Model
Connect the cables as necessary.
To connect an additional equipment, see the
EXTERNAL EQUIPMENT SETUP section.
Install the CABLE MANAGEMENT CLIP as
shown and manage the cable.
32/37/42/47/52LG60
Connect the cables as necessary.
To connect an additional equipment, see the
EXTERNAL EQUIPMENT SETUP section of
the manual.
Bundle the cables together using the supplied
CABLE MANAGEMENT CLIP.
PREPARATION
26/32/37/42/47/52LG30/50/70
CABLE MANAGEMENT CLIP
Fit the CABLE MANAGEMENT CLIP as shown.
17
PREPARATION
DESKTOP PEDESTAL INSTALLATION
■
Image shown may differ from your TV.
For proper ventilation, allow a clearance of 4 inches on all four sides from the wall.
PREPARATION
4 inches
4 inches
4 inches
4 inches
VESA WALL MOUNTING
This product accepts a VESA-compliant mounting interface pad. (optional)
There 4 threaded holes are available for attaching the bracket.
Plasma TV Model
600 mm
400 mm
LCD TV Model
200 mm
(Only 52 inches: 800 mm)
600 mm
200 mm
(52 inches: 400 mm
26, 32 inches: 100 mm)
400 mm
! NOTE
18
Screw length needed depends on the wall mount used. For further information, refer to the VESA
Wall Mounting Instruction Guide.
SWIVEL STAND
After installing the TV, you can adjust the TV set manually to the left or right direction by 20 degrees to suit
your viewing position.
PREPARATION
NOT USING THE DESK-TYPE STAND
■
Image shown may differ from your TV.
When installing the wall-mounted unit, use the protection
cover for desk-type stand installation.
ATTACHING THE TV TO A DESK (Only 26/32LG30, 32LG50)
The TV must be attached to a desk so it cannot be pulled in a forward/backward direction, potentially causing
injury or damaging the product.
Stand
1-Screw
(provided as parts of the product)
Desk
WARNING
This apparatus must be securely attached to the floor/wall per installation instructions. Tipping, shaking, or rocking the machine may cause injury/death.
19
PREPARATION
PLEASE SET IT UP CAREFULLY SO THE PRODUCT DOESN’T
FALL OVER.
■
PREPARATION
■
You should purchase necessary components to prevent TV from falling off of the stand.
Image shown may differ from your TV.
We recommend that you set up the TV close to a wall so it cannot fall over if pushed backwards.
Additionally, we recommend that the TV be attached to a wall so it cannot be pulled in a forward direction,
potentially causing injury or damaging the product.
Caution: Please make sure that children don’t climb on or hang from the TV.
■
Insert the eye-bolts (or TV brackets and bolts) to tighten the product to the wall as shown in the picture.
* If your product has the bolts in the eye-bolts position before inserting the eye-bolts, loosen the bolts.
* Insert the eye-bolts or TV brackets/bolts and tighten them securely in the upper holes.
Secure the wall brackets with the bolts (not provided as parts of the product, must purchase separately) to
the wall. Match the height of the bracket that is mounted on the wall to the holes in the product.
Ensure the eye-bolts or brackets are tightened securely.
■
Use a sturdy rope (not provided as parts of the product, must purchase separately) to tie the product. It is safer to tie the rope so it
becomes horizontal between the wall and the product.
! NOTE
20
When moving the TV, undo the cords first.
Use a platform or cabinet strong and large enough to support the size and weight of the TV
To use the TV safely make sure that the height of the bracket on the wall and on the TV is the same.
■
To prevent damage do not connect to the mains outlet until all connections are made between the devices.
ANTENNA OR CABLE CONNECTION
■
Image shown may differ from your TV.
1. Antenna (Analog or Digital)
PREPARATION
Wall Antenna Socket or Outdoor Antenna without a Cable Box
Connections.
For optimum picture quality, adjust antenna direction if needed.
Multi-family Dwellings/Apartments
(Connect to wall antenna socket)
Wall
Antenna
Socket
ANTENNA/
CABLE IN
Single-family Dwellings /Houses
(Connect to wall jack for outdoor antenna)
RF Coaxial Wire (75 ohm)
Outdoor
Antenna
(VHF, UHF)
Copper Wire
Be careful not to bend the bronze wire
when connecting the antenna.
2. Cable
ANTENNA/
CABLE IN
Cable TV
Wall Jack
RF Coaxial Wire (75 ohm)
ANTENNA/
CABLE IN
UHF
Signal
Amplifier
Antenna
VHF
To improve the picture quality in a poor signal area, please purchase a signal amplifier and install properly.
If the antenna needs to be split for two TV’s, install a 2-Way Signal Splitter.
■ If the antenna is not installed properly, contact your dealer for assistance.
■
■
! NOTE
The TV will let you know when the analog, cable, and digital channel scans are complete.
21
EXTERNAL EQUIPMENT SETUP
■
■
To prevent the equipment damage, never plug in any power cords until you have finished connecting all equipment.
This part of EXTERNAL EQUIPMENT SETUP mainly use picture for 37/42/47/52LG50 models.
HD RECEIVER SETUP
This TV can receive Digital Over-the-air/Cable signals without an external digital set-top box. However, if you do
receive digital signals from a digital set-top box or other digital external device, refer to the figure as shown below.
When connecting Component cable
EXTERNAL EQUIPMENT SETUP
1. How to connect
PB
PR
Connect the video outputs (Y, PB, PR) of the digital set
top box to the C O M P O N E N T I N V I D E O 1 jacks on
the set. Match the jack colors (Y = green, PB = blue, and
PR = red).
Connect the audio output of the digital set-top box to
the C O M P O N E N T I N A U D I O 1 jacks on the set.
RGB IN
2. How to use
■
■
■
AUDIO
(RGB/DVI)
RGB(PC)
Turn on the digital set-top box.
(Refer to the owner’s manual for the digital set-top box. operation)
Select C o m p o n e n t 1 input source by using the I N P U T
button on the remote control.
If connected to C O M P O N E N T I N 2 input, select
C o m p o n e n t 2 input source.
REMOTE
CONTROL IN
I/DVI IN
RS
(CONTR
PB
PR
AUDIO
VIDEO
COMPONENT IN
Y, CB/PB, CR/PR
Signal
22
Component
HDMI
480i
Yes
No
480p
Yes
Yes
720p
Yes
Yes
1080i
Yes
Yes
1080p
Yes
Yes
Resolution
Horizontal
Frequency(KHz)
Vertical
Frequency(Hz)
720x480i
15.73
15.73
59.94
60.00
720x480p
31.47
31.50
59.94
60.00
1280x720p
44.96
45.00
59.94
60.00
1920x1080i
33.72
33.75
59.94
60.00
1920x1080p
26.97
27.00
33.71
33.75
67.432
67.50
23.976
24.00
29.97
30.00
59.94
60.00
S-V
RGB IN
When connecting HDMI cable
HDMI/DVI IN
Connect the digital set-top box to H D M I / D V I I N 1,
2 , 3 or 4 jack on the set.
PR
PB
1 (DVI)
VIDEO
COMPONENT
No separated audio connection is necessary.
HDMI supports both audio and video.
2. How to use
EXTERNAL EQUIPMENT SETUP
1. How to connect
(RG
RGB(PC)
Turn on the digital set-top box.
(Refer to the owner’s manual for the digital set-top box.)
■ Select H D M I 1, H D M I2, H D M I 3, or H D M I 4 input source
with using the INPUT button on the remote control.
■
HDMI-DTV OUTPUT
HDMI-DTV
Resolution
Horizontal
Frequency(KHz)
Vertical
Frequency(Hz)
720x480p
31.47
31.50
59.94
60.00
1280x720p
44.96
45.00
59.94
60.00
1920x1080i
33.72
33.75
59.94
60.00
1920x1080p
26.97
27.00
33.71
33.75
67.432
67.50
23.976
24.00
29.97
30.00
59.939
60.00
23
EXTERNAL EQUIPMENT SETUP
When connecting HDMI to DVI cable
ANTENNA/
CABLE IN
RGB IN
DIGITAL AUDIO OUT
AUDIO
(RGB/DVI)
HDMI/DVI IN
COAXIAL
AUDIO OUT
1 (DVI)
OPTICAL
RS-232C IN
(CONTROL & SERVICE)
PB
PR
AUDIO
VIDEO
COMPONENT IN
DVI-DTV OUTPUT
1. How to connect
Connect the DVI output of the digital set-top box
to the H D M I / D V I I N 1 ( D V I ) jack on the set.
Connect the audio output of the digital set-top
box to the AUDIO (RGB/DVI) jack on the set.
2. How to use
■ Turn on the digital set-top box. (Refer to the
owner’s manual for the digital set-top box.)
■ Select H D M I 1 input source with using the I N P U T
button on the remote control.
24
REMOTE
CONTROL IN
S-VIDEO VIDEO L (MONO) AUDIO R
AV IN 1
EXTERNAL EQUIPMENT SETUP
RGB(PC)
DVD SETUP
When connecting Component cable
1. How to connect
Connect the video outputs (Y, PB, PR) of the DVD to the
C O M P O N E N T I N V I D E O 1 jacks on the set.
Match the jack colors (Y = green, PB = blue, and PR = red).
PB
PR
2. How to use
■
■
■
Connect the audio outputs of the DVD to the
C O M P O N E N T I N A U D I O 1 jacks on the set.
■
RGB IN
Turn on the DVD player, insert a DVD.
Select C o m p o n e n t 1 input source by using the I N P U T
button on the remote control.
If connected to C O M P O N E N T I N 2 input, select
C o m p o n e n t 2 input source.
Refer to the DVD player's manual for operating instructions.
AUDIO
(RGB/DVI)
RGB(PC)
REMOTE
CONTROL IN
VI IN
EXTERNAL EQUIPMENT SETUP
RS(CONTRO
PB
PR
VIDEO
AUDIO
COMPONENT IN
S-V
Component Input ports
To get better picture quality, connect a DVD player to the component input ports as shown below.
Component ports on the TV
Video output ports
on DVD player
PB
PR
PB
PR
B-Y
R-Y
Cb
Cr
Pb
Pr
25
EXTERNAL EQUIPMENT SETUP
When connecting with an S-Video cable
1. How to connect
Connect the S-VIDEO output of the DVD to the
S - V I D E O input on the set.
Connect the audio outputs of the DVD to the A U D I O
input jacks on the set.
2. How to use
■
■
■
Turn on the DVD player, insert a DVD.
Select A V 1 input source by using the I N P U T button on the
remote control.
Refer to the DVD player's manual for operating instructions.
ANTENNA/
CABLE IN
DIGITAL AUDIO OUT
UDIO
B/DVI)
REMOTE
CONTROL IN
OPTICAL
COAXIAL
RS-232C IN
(CONTROL & SERVICE)
AUDIO OUT
AUDIO
S-VIDEO VIDEO L (MONO) AUDIO R
AV IN 1
EXTERNAL EQUIPMENT SETUP
AUDIO
S-VIDEO
When connecting HDMI cable
AUDIO
(RGB/D
RGB(PC)
1. How to connect
HDMI/DVI IN
Connect the HDMI output of the DVD to the
H D M I / D V I I N 1, 2 , 3 or 4 jack on the set.
PB
PR
1 (DVI)
VIDEO
No separated audio connection is necessary.
HDMI supports both audio and video.
2. How to use
■
■
COMPONENT IN
Select HDMI1, H D M I2, HDMI3, or HDMI4 input source
by using the I N P U T button on the remote control.
Refer to the DVD player's manual for operating instructions.
HDMI-DVD OUTPUT
26
VCR SETUP
To avoid picture noise (interference), leave an adequate distance between the VCR and TV.
■ Use the ISM feature in the Option menu to avoid having a fixed image remain on the screen for a long period
of time (Only Plasma TV model). If the 4:3 picture format is used; the fixed images on the sides of the screen
may remain visible on the screen. This phenomenon is common to all manufactures and in consequence the
manufactures warranty does not cover the product bearing this phenomenon.
■
ANTENNA/
CABLE IN
DIGITAL AUDIO OUT
AUDIO
(RGB/DVI)
REMOTE
CONTROL IN
OPTICAL
RS-232C IN
(CONTROL & SERVICE)
AUDIO OUT
ANT OUT
S-VIDEO
ANT IN
OUTPUT
SWITCH
AUDIO
NENT IN
VIDEO
Wall Jack
S-VIDEO VIDEO L (MONO) AUDIO R
AV IN 1
PR
COAXIAL
EXTERNAL EQUIPMENT SETUP
When connecting with an antenna
Antenna
1. How to connect
Connect the RF antenna out socket of the VCR to the A N T E N N A / C A B L E I N socket on the set.
Connect the antenna cable to the RF antenna in socket of the VCR.
2. How to use
■
■
Set VCR output switch to 3 or 4 and then tune TV to the same channel number.
Insert a video tape into the VCR and press PLAY on the VCR. (Refer to the VCR owner’s manual.)
27
EXTERNAL EQUIPMENT SETUP
When connecting with a RCA cable
ANT IN
S-VIDEO
ANT OUT
OUTPUT
SWITCH
VIDEO
1. How to connect
V I D E O jacks between TV and
Connect the A U D I O/V
VCR. Match the jack colors (Video = yellow, Audio Left
= white, and Audio Right = red)
ANTENNA/
CABLE IN
EXTERNAL EQUIPMENT SETUP
DIGITAL AUDIO OUT
2. How to use
UDIO
B/DVI)
Insert a video tape into the VCR and press PLAY on the
VCR. (Refer to the VCR owner’s manual.)
■ Select A V 1 input source by using the I N P U T button on
the remote control.
■ If connected to A V I N 2, select A V 2 input source.
REMOTE
CONTROL IN
■
COAXIAL
RS-232C IN
(CONTROL & SERVICE)
AUDIO OUT
AUDIO
S-VIDEO VIDEO L (MONO) AUDIO R
! NOTE
OPTICAL
AV IN 1
If you have a mono VCR, connect the audio cable from the VCR to the A U D I O
L / M O N O jack of the set.
When connecting with an S-Video cable
ANT IN
S-VIDEO
ANT OUT
OUTPUT
SWITCH
VIDEO
1. How to connect
Connect the audio outputs of the VCR to the A U D I O
input jacks on the set.
ANTENNA/
CABLE IN
AUDIO
(RGB/DVI)
REMOTE
CONTROL IN
2. How to use
■
■
Insert a video tape into the VCR and press PLAY on the VCR.
(Refer to the VCR owner’s manual.)
Select A V 1 input source by using the I N P U T button on the
remote control.
DIGITAL AUDIO OUT
OPTICAL
RS-232C IN
(CONTROL & SERVICE)
COAXIAL
AUDIO OUT
AUDIO
NT IN
S-VIDEO VIDEO L (MONO) AUDIO R
AV IN 1
Connect the S-VIDEO output of the VCR to the
S - V I D E O input on the set.
CAUTION
! NOTE
28
The picture quality is improved: compared to normal
composite (RCA cable) input.
Do not connect to both Video
and S-Video at the same time. In
the event that you connect both
Video and the S-Video cables,
only the S-Video will work.
OTHER A/V SOURCE SETUP
Camcorder
1. How to connect
V I D E O jacks
Connect the A U D I O/V
between TV and external equipment.
Match the jack colors.
(Video = yellow, Audio Left = white, and
Audio Right = red)
Select A V 2 input source by using the I N P U T
button on the remote control.
■
If connected to A V I N 1 input, select A V 1
input source.
■
Operate the corresponding external equipment.
USB
SERVUCE ONLY
HDMI IN 3
■
VIDEO L/MONO AUDIO R
2. How to use
VIDEO
EXTERNAL EQUIPMENT SETUP
Video Game Set
AV IN 2
29
EXTERNAL EQUIPMENT SETUP
PC SETUP
This TV provides Plug and Play capability, meaning that the PC adjusts automatically to the TV's settings.
When connecting D-sub 15 pin cable
EXTERNAL EQUIPMENT SETUP
1. How to connect
RGB IN
AUDIO
(RGB/DVI)
RGB(PC)
Connect the RGB output of the PC to the R G B ( P C)
jack on the set.
REMOTE
CONTROL IN
MI/DVI IN
(CO
Connect the PC audio output to the A U D I O
( R G B / D V I) jack on the set.
PB
PR
AUDIO
VIDEO
COMPONENT IN
2. How to use
■
Turn on the PC and the TV.
■
Select R G B - P C input source by using the I N P U T button
on the remote control.
RGB OUTPUT
AUDIO
! NOTES
30
For LCD TV: To get the the best picture quality,
adjust the PC graphics card to 1366x768.
For Plasma TV: To get the the best picture quality,
adjust the PC graphics card to 1360x768.
Depending on the graphics card, DOS mode may
not work if a HDMI to DVI Cable is in use.
Check the image on your TV. There may be noise
associated with the resolution, vertical pattern,
contrast or brightness in PC mode. If noise is
present, change the PC output to another resolution, change the refresh rate to another rate or
adjust the brightness and contrast on the
PICTURE menu until the picture is clear. If the
refresh rate of the PC graphic card can not be
changed, change the PC graphic card or consult
the manufacturer of the PC graphic card.
Avoid keeping a fixed image on the screen for a
long period of time. The fixed image may become
permanently imprinted on the screen.
The synchronization input form for Horizontal and
Vertical frequencies is separate.
When connecting HDMI to DVI cable
CABLE IN
RGB IN
DIGITAL AUDIO OUT
REMOTE
CONTROL IN
HDMI/DVI IN
RS-232C IN
(CONTROL & SERVICE)
AUDIO OUT
1 (DVI)
COAXIAL
PB
PR
AUDIO
VIDEO
COMPONENT IN
DVI-PC OUTPUT
S-VIDEO VIDEO L (MONO) AUDIO R
AV IN 1
OPTICAL
EXTERNAL EQUIPMENT SETUP
AUDIO
(RGB/DVI)
RGB(PC)
AUDIO
1. How to connect
Connect the DVI output of the PC to the
H D M I / D V I I N 1 ( D V I ) jack on the set.
Connect the PC audio output to the A U D I O
( R G B / D V I ) jack on the set.
2. How to use
■
■
Turn on the PC and the TV.
Select H D M I 1 input source with using the
I N P U T button on the remote control.
31
EXTERNAL EQUIPMENT SETUP
Supported Display Specifications (RGB-PC, HDMI-PC)
For 26/32/37/42LG30
For 37/42/47/52LG50,32/37/42/47/52LG60
32/42/47/52LG70
EXTERNAL EQUIPMENT SETUP
Resolution
Horizontal
Frequency(KHz)
Vertical
Frequency(Hz)
Resolution
Horizontal
Frequency(KHz)
Vertical
Frequency(Hz)
640x350
31.469
70.08
640x350
31.468
70.09
720x400
31.469
70.08
720x400
31.469
70.08
640x480
31.469
59.94
640x480
800x600
37.879
60.31
31.469
37.500
37.861
59.94
75.00
72.80
1024x768
48.363
60.00
1280x768
47.776
59.87
800x600
35.156
37.879
46.875
48.077
56.25
60.31
75.00
72.18
1360x768
47.720
59.799
1024x768
48.363
56.476
60.023
60.00
70.06
75.02
1280x768
47.776
60.289
59.87
74.893
1280x1024
63.981
79.976
60.02
75.025
1360x768
47.712
60.015
1600x1200
75.00
60.00
66.587
59.934
67.5
60.00
1366x768
47.130
59.65
* Only RGB-PC mode
1920x1080
RGB-PC
1920x1080
HDMI-PC
* Only RGB-PC mode
! NOTE
32
Depending on graphic card and signal status, there can be some shaking to find best picture in a little time.
For 50/60PG60F
For 42/50PG20
Horizontal
Frequency(KHz)
Vertical
Frequency(Hz)
Resolution
Horizontal
Frequency(KHz)
Vertical
Frequency(Hz)
640x350
31.468
70.09
640x350
31.468
70.09
720x400
31.469
70.08
720x400
31.469
70.08
640x480
31.469
37.500
37.861
59.94
75.00
72.80
640x480
31.469
37.500
37.861
59.94
75.00
72.80
800x600
35.156
37.879
46.875
48.077
56.25
60.31
75.00
72.18
800x600
35.156
37.879
46.875
48.077
56.25
60.31
75.00
72.18
1024x768
48.363
56.476
60.023
60.00
70.06
75.02
1024x768
48.363
56.476
60.023
60.00
70.06
75.02
1280x768
47.776
60.289
59.87
74.893
1280x768
47.776
60.289
59.87
74.893
1280x1024
63.981
79.976
60.02
75.025
1280x1024
63.981
79.976
60.02
75.025
1360x768
47.712
60.015
1360x768
47.712
60.015
1600x1200
75.00
60.00
1600x1200
75.00
60.00
1920x1080
66.587
59.934
1920x1080
67.5
60.00
EXTERNAL EQUIPMENT SETUP
Resolution
* Only RGB-PC mode
! NOTE
Depending on graphic card and signal status, there can be some shaking to find best picture in a little time.
33
EXTERNAL EQUIPMENT SETUP
Screen Setup for PC mode
Selecting Resolution
PICTURE
Move
Enter
EXTERNAL EQUIPMENT SETUP
When you change the resolution, select the proper resolution in present input to see the best picture appearance.
XGA (1024, 1280, 1360) isn’t distinguished because of having the same H/V Sync Time. This function is you
to select the Default Sync Time.
This feature operates only in RGB-PC mode.
• Advanced Control
SCREEN
Resolution
• Picture Reset
Auto Config.
Screen (RGB-PC)
TruMotion Demo
Position
Size
Phase
Reset
1 MENU
Select P I C T U R E.
ENTER
Select S C R E E N ( R G B - P C ).
ENTER
Select R e s o l u t i o n.
Select the desired resolution.
ENTER
34
Move
MENU Prev.
1024 x 768
1280 x 768
1360 x 768
Auto Configure
Automatically adjusts picture position and minimizes image instability. After adjustment, if the image is still
not correct, your TV is functioning properly but needs further adjustment.
PICTURE
Move
Enter
• Advanced Control
SCREEN
Move
MENU Prev.
Resolution
• Picture Reset
Auto Config. G
Screen (RGB-PC)
TruMotion Demo
Position
Auto config.
Size
EXTERNAL EQUIPMENT SETUP
Auto configure
This function is for automatic adjustment of the screen position, clock, and phase The displayed image will
be unstable for a few seconds while the auto configuration is in progress.
Phase
Reset
1 MENU
Select P I C T U R E.
ENTER
Select S C R E E N ( R G B - P C ).
ENTER
Select A u t o C o n f i g ..
ENTER
Select Y e s.
ENTER
• If the position of the image is still not
correct, try Auto adjustment again.
• If picture needs to be adjusted again
after Auto adjustment in RGB-PC, you
can adjust the P o s i t i o n , S i z e or
P h a s e.
Start Auto Configuration.
35
PREPARATION
Adjustment for screen Position, Size, and Phase
PREPARATION
If the picture is not clear after auto adjustment and especially if characters are still trembling, adjust the picture
phase manually.
This feature operates only in RGB-PC mode.
PICTURE
Move
Enter
• Advanced Control
SCREEN
Move
MENU Prev.
Resolution
• Picture Reset
Auto Config.
Screen (RGB-PC)
TruMotion Demo
Position
Size
Phase
Reset
1 MENU
ENTER
Select S C R E E N ( R G B - P C ).
ENTER
Select P o s i t i o n, S i z e, or P h a s e.
ENTER
Make appropriate adjustments.
ENTER
36
Select P I C T U R E.
• P o s i t i o n: This function is to adjust picture to left/right and up/down as you
prefer.
• S i z e: This function is to minimize any
vertical bars or stripes visible on the
screen background. And the horizontal
screen size will also change. The S i z e
adjustment range is -30 ~ 30.
• P h a s e: This function allows you to
remove any horizontal noise and clear or
sharpen the image of characters. The
Phase adjustment range is -16 ~ 16.
Screen Reset (Reset to original factory values)
PICTURE
Move
Enter
• Advanced Control
SCREEN
Move
PREPARATION
Returns to the default settings Resolution, Auto Config., Position, Size and Phase at the factory.
This feature operates only in RGB-PC mode.
MENU Prev.
Resolution
• Picture Reset
Auto Config.
Screen (RGB-PC)
TruMotion Demo
Position
To Set
Size
Phase
Reset
1 MENU
Select P I C T U R E.
ENTER
Select S C R E E N ( R G B - P C ).
ENTER
Select R e s e t.
ENTER
Select Y e s.
ENTER
37
EXTERNAL EQUIPMENT SETUP
or
VIDEO L/MONO AUDIO R
EXTERNAL EQUIPMENT SETUP
HDMI IN 3
USB
SERVUCE ONLY
USB IN SETUP
AV IN 2
1. How to connect
Connect the USB device to the U S B S E R V I C E O N L Y
jack on the side of TV.
2. How to use
■
After connecting the U S B jack, you use the USB function.
(G p .56)
38
AUDIO OUT SETUP
Send the TV’s audio to external audio equipment via the Audio Output port.
CABLE IN
Analog
REMOTE
CONTROL IN
RS-232C IN
(CONTROL & SERVICE)
Connect audio outputs to the TV’s AUDIO OUT jacks.
OPTICAL
COAXIAL
EXTERNAL EQUIPMENT SETUP
1. How to connect
DIGITAL AUDIO OUT
VI)
AUDIO OUT
Set the “TV Speaker option - Off” in the AUDIO menu.
(G p . 8 5). See the external audio equipment instruction
manual for operation.
AUDIO
S-VIDEO VIDEO L (MONO) AUDIO R
AV IN 1
Digital
1. How to connect
AUDIO
Connect one end of the optical or coaxial cable to the TV’s
O P T I C A L or COAXIAL (Except **LG30) port of DIGITAL
AUDIO OUT.
Connect the other end of the optical or coaxial cable to the
digital audio input on the audio equipment.
ANTENNA/
CABLE IN
DIGITAL AUDIO OUT
AUDIO
(RGB/DVI)
REMOTE
CONTROL IN
RS-232C IN 1
(CONTROL & SERVICE)
! NOTE
When connecting with external audio equipments, such as amplifiers or speakers, please turn the TV speakers off. (G p . 8 5)
OPTICAL
AUDIO OUT
AUDIO
NT IN
COAXIAL
S-VIDEO VIDEO L (MONO) AUDIO R
AV IN 1
Set the “TV Speaker option - Off” in the AUDIO menu. (G
p .85). See the external audio equipment instruction manual
for operation.
CAUTION
Do not look into the optical output port. Looking at the
laser beam may damage your vision.
Block the SPDIF out (optical/coaxial) about the contents
with ACP(Audio Copy Protection) function.
39
WATCHING TV / CHANNEL CONTROL
REMOTE CONTROL FUNCTIONS
When using the remote control, aim it at the remote control sensor on the TV.
TV/STB/DVD/VCR Select the remote operating mode: TV, STB, DVD, or VCR.
* If the mode of another product is selected, a button on
the remote control which is not used for the selected
product can control the TV.
TV
DVD
VCR
Q. MENU MENU INPUT
STB
WATCHING TV / CHANNEL CONTROL
POWER Turns your TV or any other programmed equipment on or
off, depending on the mode.
Q.MENU Select the desired quick menu source. G p .43
MENU Displays the main menu.
Clear all on-screen displays and return to TV viewing from
any menu.
ENTER
RETURN
AV MODE
INPUT External input modes rotate in regular sequence
VOLUME UP Increase/decrease the sound level.
/DOWN
FAV Scroll through the programmed Favorite channels. G p.43
FAV
CHANNEL Select available channels.
UP/DOWN
PAGE Move from one full set of screen information to the next one.
UP/DOWN
NUMBER button
— (DASH) Used to enter a program number for multiple
program channels such as 2-1, 2-2, etc.
FLASHBK Tune to the last channel viewed.
VCR/DVD
buttons
Control video cassette recorders or DVD players.
Control USB menu (PHOTO LIST and MUSIC LIST.)
Control the SIMPLINK compatible devices.
CH
VOL
MUTE Switch the sound on or off. G p.42
40
POWER
MUTE
FLASHBK
THUMBSTICK Navigate the on-screen menus and adjust the system settings to your preference.
(Up/Down/Left
Right/ENTER)
RETURN Allows the user to move return one step in an interactive application or other user interaction
function.
AV MODE It helps you select and set images and sounds when connecting AV devices. G p.53
WATCHING TV / CHANNEL CONTROL
SIMPLINK See a list of AV devices connected to TV.
When you toggle this button, the SimpLink menu appears at the screen. G p.54-55
Installing Batteries
■
Open the battery compartment cover on the back side and install
the batteries matching correct polarity (+with +,-with -).
■
Install two 1.5V AAA batteries. Don’t mix old or used batteries with
new ones.
■
Close cover.
41
WATCHING TV / CHANNEL CONTROL
TURNING ON TV
First, connect power cord correctly.
At this moment, the TV switches to standby mode.
■ In standby mode to turn TV on, press the
, INPUT, CH (D or E)
), Number (0~9
9)
button on the TV or press the POWER, INPUT, CH(
button on the remote control.
WATCHING TV / CHANNEL CONTROL
Select the viewing source by using the INPUT button on the remote control.
■ This TV is programmed to remember which power state it was last set to,
even if the power cord is out.
When finished using the TV, press the POWER button on the remote control.
The TV reverts to standby mode.
! NOTE
If you intend to be away on vacation, disconnect the power plug from the wall power outlet.
CHANNEL SELECTION
Press the C H (
) or NUMBER buttons to select a channel number.
VOLUME ADJUSTMENT
Adjust the volume to suit your personal preference.
42
Press the V O L ( + or - ) button to adjust the volume.
If you want to switch the sound off, press the M U T E button.
You can cancel the Mute function by pressing the MUTE or V O L ( + or - )
button.
QUICK MENU
Your TV's OSD (On Screen Display) may differ slightly from what is shown in this manual.
Q.Menu (Quick Menu) is a menu of features which users might use frequently.
• S o u n d M o d e: Selects the factory preset sound for
type of program.
• C a p t i o n: Select a closed caption.
• M u l t i A u d i o: Selects MTS sound (Analog signal)
or changes the audio language (Digital signal).
• S l e e p T i m e r: Select the amount of time before
your TV turns off automatically.
• D e l / A d d / F a v: Select channel you want to add or
delete or add the channel to the Favorite List.
• U S B E j e c t: Select “USB Eject” in order to eject
USB device.
Plasma TV
LCD TV
Q-Menu
Q-Menu
Aspect Ratio
16:9
Power Saving
Clear Voice
16:9
Brightness
Off
Clear Voice
Off
Picture Mode
Vivid
Picture Mode
Vivid
Sound Mode
Standard
Sound Mode
Standard
Off
Caption
Sleep Timer
Off
Del/Add/Fav
Add
USB Eject
Eject
Close
Only for 50/60PG60F
English
Multi Audio
CH
Off
Caption
English
Multi Audio
CH
Aspect Ratio
WATCHING TV / CHANNEL CONTROL
• A s p e c t R a t i o: Selects your desired picture format.
• P o w e r S a v i n g (Only Plasma TV): Adjusts screen
brightness to reduce the power consumption of the
TV.
• B r i g h t n e s s (Only LCD TV): Adjusts screen
brightness. It returns to the default settings brightness by changing mode source.
• l e a r V o i c e: By differentiating the human sound
range from others, it helps users listen to human
voices better.
• P i c t u r e M o d e: Selects the factory preset picture
depend on the viewing environment.
Sleep Timer
Off
Del/Add/Fav
Add
USB Eject
Eject
Close
Only for 32/37/42/47/52LG50/60/70
1Q. MENU
Display each menu.
3Q. MENU
Make appropriate adjustments.
Return to TV viewing
43
WATCHING TV /CHANNEL CONTROL
INITIAL SETTING
This OSD (On Screen Display) is displayed automatically on the screen as figure after turning on the TV and
you can adjust the Location, Time, Language, Auto tuning.
Step1. Mode setting
Step1. Mode Setting
Select H o m e M o d e.
WATCHING TV / CHANNEL CONTROL
It sets a use environment.
Select the set where mode.
Home
In-Store
Enter
RETURN
ENTER
Exit
Step2. Time setting
Step2. Time Setting
Current Time Setting
Year
Auto
11
Date
15
Hour
5 PM
Minute
Daylight Saving
Enter
Select A u t o or M a n u a l.
2007
Month
Time Zone
44
Select desired time option.
52
Eastern
Off
RETURN Exit
ENTER
Step3. Option setting
Step3. Option Setting
English
2. Audio Language Setting
Select O S D L a n g u a g e S e t t i n g or
A u d i o L a n g u a g e S e t t i n g.
French
Enter
RETURN Exit
Select your desired language.
ENTER
Step4. Auto Tuning
Step4. Auto Tuning
Auto Tuning can change channel map.
Do you want to start Auto Tuning?
ENTER
Start A u t o T u n i n g.
WATCHING TV / CHANNEL CONTROL
1. OSD Language Setting
Enter
Enter
RETURN Exit
! NOTE
• You can also adjust I n i t i a l S e t t i n g in the O P T I O N menu.
OPTION
Move
Enter
1 MENU
Select O P T I O N.
Initial Setting
ENTER
Select I n i t i a l S e t t i n g.
ENTER
45
WATCHING TV /CHANNEL CONTROL
ON-SCREEN MENUS SELECTION
Your TV's OSD (On Screen Display) may differ slightly from that shown in this manual.
* Only 32/37/42/47/52LG50/60/70, 50/60PG60F
CHANNEL
Move
PICTURE
Enter
Move
Auto Tuning
Aspect Ratio : 16:9
Manual Tuning
Picture Mode : Standard
Channel Edit
AUDIO
Enter
Move
Auto Volume
: Off
Clear Voice
: On
WATCHING TV / CHANNEL CONTROL
• Backlight
50
Balance
• Contrast
50
Sound Mode
• Brightness
50
• SRS TruSurround XT: Off
• Sharpness
50
• Treble
50
• Color
50
• Bass
50
• Tint
: Standard
Move
Language
TIME
Enter
Clock
Input Label
CHANNEL
: On
PICTURE
AUDIO
TIME
Move
Enter
: DC/9/ 2007 02:10 AM
Off Time
: Off
On Time
: Off
Key Lock
: Off
Sleep Timer : Off
Caption
: Off
Auto Sleep : Off
ISM Method
Power Saving
: Level 0
Set ID
:1
OPTION
LOCK
INPUT
USB
LOCK
Move
Lock System
INPUT
Enter
: Off
Lock System
: Off
Move
Enter
USB
Antenna
PHOTO LIST
MUSIC LIST
Set Password
Set Password
Cable
Block Channel
Block Channel
AV1
Movie Rating
TV Rating-English
AV2
TV Rating-Children
TV Rating-French
Component1
TV Rating-General
Downloadable Rating
Component2
Downloadable Rating
Input Block
RGB-PC
Input Block
Move
HDMI1
For USA
1 MENU
ENTER
For Canada
Display each menu.
Select a menu item.
! NOTE
ENTER
4 MENU
46
: English
SIMPLINK
• Reset
OPTION
Enter
Enter to the pop up menu.
Return to TV viewing
I S M M e t h o d, P o w e r S a v i n g: Only
P l a s m a T V.
B a c k l i g h t: Only L C D T V.
T r u M o t i o n D e m o: Only
3 2 / 3 7 / 4 2 / 4 7 / 5 2 L G 6 0 / 7 0.
P o w e r I n d i c a t o r: Only
3 2 / 3 7 / 4 2 / 4 7 / 5 2 L G 6 0.
Enter
Only 26/32/37/42LG30, 42/50/PG10/20
CHANNEL
Move
Enter
PICTURE
Move
Auto Tuning
Aspect Ratio : 16:9
Manual Tuning
Picture Mode : Standard
Channel Edit
AUDIO
Enter
Move
Auto Volume
: Off
Clear Voice
: On
• Backlight
50
Balance
• Contrast
50
Sound Mode
• Brightness
50
• SRS TruSurround XT: Off
• Sharpness
50
• Treble
50
• Color
50
• Bass
50
Move
• Reset
Clock
: Standard
WATCHING TV / CHANNEL CONTROL
• Tint
TIME
Enter
Enter
: DC/9/ 2007 02:10 AM
Off Time
: Off
On Time
: Off
CHANNEL
PICTURE
AUDIO
TIME
OPTION
LOCK
Sleep Timer : Off
Auto Sleep : Off
OPTION
Move
Language
Enter
: English
Input Label
LOCK
Move
Lock System
: Off
Enter
Lock System
Set Password
Set Password
: Off
SIMPLINK
: On
Block Channel
Block Channel
Key Lock
: Off
Movie Rating
TV Rating-English
Caption
: Off
TV Rating-Children
TV Rating-French
TV Rating-General
Downloadable Rating
Input Block
ISM Method
Power Saving
: Level 0
Downloadable Rating
Set ID
:1
Input Block
For USA
1 MENU
ENTER
Display each menu.
Select a menu item.
NOTE
ENTER
4 MENU
For Canada
I S M M e t h o d, P o w e r S a v i n g: Only
P l a s m a T V.
B a c k l i g h t: Only L C D T V.
Enter to the pop up menu.
Return to TV viewing
47
WATCHING TV /CHANNEL CONTROL
CHANNEL SETUP
Auto Scan (Auto Tuning)
Automatically finds all channels available through antenna or cable inputs, and stores them in memory on the
channel list.
Run Auto Tuning again after any Antenna/Cable connection changes.
WATCHING TV / CHANNEL CONTROL
CHANNEL
Move
Enter
Move
Auto Tuning
Manual Tuning
Manual Tuning
Channel Edit
Channel Edit
Enter
Press ‘Yes’ button to begin
auto tuning.
Yes
No
1 MENU
ENTER
Select C H A N N E L.
Select A u t o T u n i n g.
ENTER
ENTER
5RETURN
MENU
48
CHANNEL
Auto Tuning
Select Y e s.
Run A u t o t u n i n g.
Return to the previous menu.
Return to TV viewing
■
A password is required to gain access to
Auto Tuning menu if the Lock System is
turned on.
Add/Delete Channel (Manual Tuning)
If selecting DTV or CADTV input signal, you can view the on-screen signal strength monitor to see the quality
of the signal being received.
CHANNEL
Move
Enter
CHANNEL
Move
Auto Tuning
Manual Tuning
Manual Tuning
Channel Edit
Channel Edit
DTV
Select channel type and
RF-channel number.
Channel
DTV 2-0
Bad
Normal
Good
Delete
Close
1 MENU
Select C H A N N E L.
Select M a n u a l T u n i n g.
ENTER
■
ENTER
Select D T V, T V, C A D T V, or C A T V.
WATCHING TV / CHANNEL CONTROL
Auto Tuning
Enter
A password is required to gain access to
Manual Tuning menu if the Lock System
is turned on.
Select channel you want to add
or delete.
ENTER
6RETURN
MENU
Select A d d or D e l e t e.
Return to the previous menu.
Return to TV viewing
49
WATCHING TV / CHANNEL CONTROL
CHANNEL SETUP
Channel Editing
From the default channel list created from the Auto Tuning channel search, you can create two different types
of channel lists in memory: “custom list” and “favorite channel list”.
A custom list can be created by toggling each channel on or off with ENTER button. The channels in the Custom
List are displayed in black and the channels deleted from the Custom List are displayed in gray.
Once a channel is highlighted you can add or delete the channel by referring to the small window at the topleft corner of the screen.
WATCHING TV / CHANNEL CONTROL
CHANNEL
Move
Enter
Auto Tuning
Manual Tuning
Channel Edit
Add/Delete
1 MENU
Select C H A N N E L.
ENTER
Select C h a n n e l E d i t.
ENTER
Select a channel.
ENTER
5 MENU
RETURN
50
Select channel you want to add or
delete.
Return to the previous menu.
Return to TV viewing
Navigate CH
Move Page
MENU Previous
RETURN Exit
Source Exif Data: 
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 52
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:bf384c0a-b4fc-4044-8daf-535e2b7623db
Modify Date                     : 2007:12:20 10:21:57+09:00
Create Date                     : 2007:12:20 10:21:52+09:00
Metadata Date                   : 2007:12:20 10:21:57+09:00
Document ID                     : uuid:d19dca98-c749-4387-8076-71402563c4ef
Format                          : application/pdf
Title                           : PQ_SAC30708020-Edit1-en
Creator                         : 3.3: LaserWriter 8 Z1-8.7.1
Author                          : sun
Producer                        : Acrobat Distiller 4.0.5  for Macintosh
EXIF Metadata provided by EXIF.tools
FCC ID Filing: BEJ42LG30UA

Navigation menu