LG Electronics USA 42PC3DUUE Plasma Display Panel User Manual 38289U0527F LG PDP
LG Electronics USA Plasma Display Panel 38289U0527F LG PDP
Contents
- 1. User Manual 1
- 2. User Manual 2
- 3. User Manual 3
User Manual 2
Basic Connection How to use stand (For 42PC3DU/3DVU) Place the set with the screen facing down on a cushion or soft cloth as shown. Before unfolding the stand, please make sure two locks (A) on the bottom of the stand push outward. Pull the stand out as shown. After unfolding the stand, please insert and tighten the screws (provided as parts of the product) in the holes (B) on the bottom of the stand. (A) (B) When connecting cables to the set, Do not disengage the lock (C). This may cause the set to fall, causing serious bodily injury and serious damage to the set. (C) * Image shown here may be slightly different from your set. When closing the stand for storage - First remove the screws in the holes (B) on the bottom of the stand. And then pull two Hooks (D) of the stand bottom and fold the stand into the back of the set. - After folding, push the two Locks (A) of the stand bottom outward. (A) (B) (D) How to arrange the cable (For 50PC3DU) Hold the CABLE MANAGEMENT with both hands and push it as shown. Reinstall the CABLE MANAGEMENT as shown. Connect the cables as necessary. To connect an additional equipment, see the External equipment Connections section. For 60PC1D, 42PC3DU/3DVU Arrange the cable as shown. 17 Installation External Equipment Connections NOTE: All cables shown are not included with the TV Antenna Or Cable Connection Analog and Digital TV signals provided on antenna - Antenna or Cable Service without a Cable Box Connection. - For optimum picture quality, adjust antenna direction if needed. Multi-family Dwellings/Apartments (Connect to wall antenna socket) Wall Antenna Socket OPTICAL ANTENNA/ CABLE IN DIGITAL AUDIO OUT RF Coaxial Wire (75 ohm) VHF Antenna Turn clockwise to tighten. UHF Antenna Outdoor Antenna Bronze Wire Be careful not to bend the bronze wire when connecting the antenna. Single-family Dwellings /Houses (Connect to wall jack for outdoor antenna) Analog and Digital TV signals provided on cable Cable TV Wall Jack OPTICAL ANTENNA/ CABLE IN RF Coaxial Wire (75 ohm) DIGITAL AUDIO OUT Turn clockwise to tighten. Analog and DTV signals provided on two separate antennas Bronze Wire Antenna RF Coaxial Wire (75 ohm) Turn clockwise to tighten. Cable TV Wall Jack RF Coaxial Wire (75 ohm) • In a poor signal area to improve picture quality, purchase and install a signal amplifier. • If OPTICAL the antenna needs to be split for two TV’s, install a “2-Way Signal Splitter” in the connections. DIGITAL AUDIO S-VIDEO VIDEO AUDIO OUT antenna is not installed properly, contact your dealer for assistance. • If the AV OUT AV IN 1 signal amplifier COMPONENT IN Bronze Wire AUDIO VIDEO ANTENNA/ CABLE IN ANTENNA/ CABLE IN VIDE 18 S-VID Installation VCR Setup - To avoid picture noise (interference), leave an adequate distance between the VCR and TV. - Typically a frozen still picture from a VCR. If the 4:3 picture format is used; the fixed images on the sides of the screen may remain visible on the screen. When connecting with an antenna Connect the RF antenna out socket of the VCR to the Antenna socket on the set. Connect the antenna cable to the RF antenna in socket of the VCR. Set VCR output switch to 3 or 4 and then tune TV to the same channel number. Insert a video tape into the VCR and press PLAY on the VCR. (Refer to the VCR owner’s manual.) Connect the AUDIO/VIDEO jacks between TV and VCR. Match the jack colors (Video = yellow, Audio Left = white, and Audio Right = red) Insert a video tape into the VCR and press PLAY on the VCR. (Refer to the VCR owner’s manual.) Select AV1 input source using the INPUT button on the remote control. - If connected to AV IN2, select AV2 input source. VCR ANT IN ANT OUT S-VIDEO OUT (R) AUDIO (L) VIDEO OUTPUT SWITCH IN SERVICE RGB IN (PC) AUDIO IN (RGB/DVI) HDMI IN REMOTE CONTROL IN 1(DVI) ANTENNA/ SERVICE CABLE IN IN RGBRS-232C IN (CONTROL & SERVICE) SERVICE) (PC) REMOTE CONTROL IN AUDIO IN (RGB/DVI) HDMI / DVI IN ANTENNA/ CABLE IN RS-232C IN (CONTROL & SERVICE) When connecting with a RCA cable VCR ANT IN OUT S-VIDEO ANT OUT (R) AUDIO (L) VIDEO OUTPUT SWITCH IN OPTICAL COMPONENT IN DIGITAL AUDIO VIDEOS-VIDEO VIDEOAUDIO AUDIO OUT AV OUT AV IN 1 OPTICAL PTICAL DIGITAL AUDIO OUT (MONO) S-VIDEO VIDEO AV OUT AV IN 1 COMPONENT IN AUDIO VIDEO AUDIO • If you have a mono VCR, connect the audio cable from the VCR to the AUDIO L/MONO jack of the set. OPTICAL VIDEOS-VIDEO AUDIO VIDEO COMPONENT IN AV OUT A DIGITAL AUDIO OUT AUDIO COMPONENT IN AV OUT AV IN 1 AUDIO VIDEO 19 Installation S-VIDEO VIDEO AUDIO AV OUT AV IN 1 OPTICAL DIGITAL AUDIO OUT COMPONENT IN AUDIO VIDEO When connecting with an S-Video cable VCR Connect the S-VIDEO output of the VCR to the SVIDEO input on the set. The picture quality is improved; compared to normal composite (RCA cable) input. Connect the audio outputs of the VCR to the AUDIO input jacks on the set. Insert a video tape into the VCR and press PLAY on the VCR. (Refer to the VCR owner’s manual.) Select AV1 input source with using the INPUT button on the remote control. - If connected to AV IN2, select AV2 input source. ANT IN S-VIDEO OUT ANT OUT (R) AUDIO (L) VIDEO OUTPUT SWITCH IN OPTICAL PTICAL DIGITAL AUDIO DIGITAL OUT (MONO) S-VIDEO VIDEO AUDIO COMPONENT IN AV OUT AV IN 1 AUDIO VIDEO Do not connect to both Video and S-Video at the same time. In the event that you connect both Video and the S-Video cables, only the S-Video will work. External AV Source Setup Connect the AUDIO/VIDEO jacks between TV and external equipment. Match the jack colors (Video = yellow, Audio Left = white, and Audio Right = red). Select AV2 input source with using the INPUT button on the remote control. - If connected to AV IN1 input, select AV1 input source. Operate the corresponding external equipment. Refer to external equipment operating guide. Camcorder Video Game Set 20 AUDIO R VIDEO • This TV finds the connected input sources automatically for AV1, AV2, Component 1-2, RGB, HDMI1/DVI and HDMI2 sources are connected. HDMI / DVI IN ANTENNA/ CABLE IN COMPONENT IN AUDIO VIDEO Installation DVD Setup When connecting with a S-Video cable DVD (R) AUDIO (L) S-VIDEO COMPONENT IN AUDIO VIDEO AV V OUT AV V IN 1 OPTICAL PTICAL DIGITAL AUDIO DIGITAL OUT (MONO) S-VIDEO VIDEO AUDIO Connect the S-VIDEO output of the DVD to the S-VIDEO input on the set. Connect the audio outputs of the DVD to the AUDIO input jacks on the set. Turn on the DVD player, insert a DVD. Select AV1 input source with using the INPUT button on the remote control. - If connected to AV IN2, select AV 2 input source. Refer to the DVD player's manual for operating instructions. When connecting with a HDMI cable HDMI IN 1(DVI) ANTENNA/ CABLE IN COMPONENT IN AUDIO VIDEO DVD HDMI-DVD OUTPUT Connect the HDMI output of the DVD to the HDMI IN 1(DVI) or 2 jack on the set. Select HDMI1/DVI or HDMI2 input source with using the INPUT button on the remote control. Refer to the DVD player's manual for operating instructions. S-VIDEO VIDEO AUDIO AV OUT AV IN 1 OPTICAL DIGITAL AUDIO OUT COMPONENT IN AUDIO VIDEO • TV can receive the video and audio signal simultaneously with using a HDMI cable. • If the DVD supports Auto HDMI function, the DVD output resolution will be automatically set to 1280x720p. • If the DVD does not support Auto HDMI, you need to set the output resolution appropriately. To get the best picture quality, adjust the output resolution of the DVD to 1280x720p. 21 Installation When connecting with a component cable DVD (R) AUDIO (L) HDMI / DVI IN ANTENNA/ CABLE IN VIDEO AUDIO COMPONENT IN Connect the video outputs (Y, PB, PR) of the DVD to the COMPONENT IN VIDEO jacks on the set. Connect the audio outputs of the DVD to the COMPONENT IN AUDIO jacks on the set. Turn on the DVD player, insert a DVD. Select Component 1 input source with using the INPUT button on the remote control. - If connected to COMPONENT 2, select Component 2 input source. Refer to the DVD player's manual for operating instructions. AUDIO VIDEO Video output ports on DVD player 22 PB PR Pr Y OPTICALPb R-YVIDEO YDIGITAL AUDIO B-Y S-VIDEO OUT Cb Cr PB PR AUDIO AV OUT AV IN 1 Component ports on the TV COMPONENT IN • Component Input ports To get better picture quality, connect a DVD player to the component input ports as shown below. Installation HDSTB Setup - This TV can receive Digital Over-the-air/Cable signals without an external digital set-top box. However, if you do receive Digital signals from a digital set-top box or other digital external device, refer to the figure as shown below. When connecting with a HDMI cable SERVICE RGB IN (PC) REMOTE CONTROL IN Connect the HDMI output of the digital set-top box to the HDMI IN 1(DVI) or 2 jack on the set. RS-232C IN (CONTROL & SER SERVICE) VICE) Select HDMI1/DVI or HDMI2 input source with using the INPUT button on the remote control. Turn on the digital set-top box. (Refer to the owner’s manual for the digital set-top box.) AUDIO IN (RGB/DVI) HDMI IN 1(DVI) COMPONENT IN AV OUT AV IN 1 Digital Set-top Box HDMI-DTV OUTPUT RGB IN (PC) AUDIO IN (RGB/DVI) • TV can receive the video and audio signal simultaneously using a HDMI cable. • If the digital set-top box supports Auto HDMI function, output resolution of the digital set-top box will be automatically set to 1280x720p. • If the digital set-top box does not support Auto HDMI, you need to set the output resolution appropriately. To get the best picture quality, adjust the output resolution of the digital set-top box to 1280x720p. REMOTE CONTROL IN When connecting with a Component cable RS-232C IN (CONTROL & SERVICE) Digital Set-top Box Connect the video outputs (Y, PB, PR) of the digiSERVICE RGB IN tal set-top box to the COMPONENT IN VIDEO jacks on the set. (PC) (R) AUDIO (L) OPTICAL PTICAL (PC) DIGITAL AUDIO DIGITAL OUT Turn on the digital set-top RS-232C box.IN (Refer to the & SERVICE) owner’s manual for the digital(CONTROL set-top box.) Select Component 1 input source with using the INPUT button on the remote control. - If connected to COMPONENT 2, select Component 2 input source. (MONO) S-VIDEO VIDEO AUDIO AV V OUT AV V IN 1 RGB IN COMPONENT IN AUDIO VIDEO Signal RGBAUDIO IN IN REMOTE CONTROL IN REMOTE CONTROL IN Connect the audio output of the digital set-top box to the COMPONENT IN AUDIO jacks on the set. HDMI / DVI IN AUDIO IN (RGB/DVI) Component1/2 HDMI1/DVI, HDMI2 480i Yes No 480p/720p/1080i Yes Yes (RGB/DVI) RS-232C IN (CONTROL & SERVICE) 23 SERVICE RGB IN (PC) AUDIO IN (RGB/DVI) HDMI / DVI IN REMOTE CONTROL IN 1(DVI) RS-232C IN (CONTROL & SERVICE) Installation S-VIDEO VIDEO AUDIO AV OUT AV IN 1 OPTICAL DIGITAL AUDIO OUT COMPONENT IN AUDIO VIDEO When connecting with a HDMI to DVI cable SERVICE RGB IN (PC) AUDIO IN (RGB/DVI) REMOTE CONTROL IN HDMI IN 1(DVI) RS-232C IN (CONTROL & SERVICE) SERVICE) DVI-DTV OUTPUT (R) AUDIO (L) Digital Set-top Box Connect the DVI output of the digital set-top box to the HDMI IN 1(DVI) jack on the set. Connect the audio outputs of the set-top box to the AUDIO IN(RGB/DVI) jack on the set. Turn on the digital set-top box. (Refer to the owner’s manual for the digital set-top box.) RGB IN (PC) RGBAUDIO IN IN REMOTE CONTROL IN (RGB/DVI) Select HDMI1/DVI input source with using the INPUT button on the remote control. RS-232C IN (CONTROL & SERVICE) • If the digital set-top box has a DVI output and no HDMI output, a separated audio connection is necessary. • If the digital set-top box supports Auto DVI function, the output resolution of the digital set-top box will be automatically set to 1280x720p. • If the digital set-top box does not support Auto DVI, you need to set the output resolution appropriately. To get the best picture quality, adjust the output resolution of the digital set-top box to 1280x720p. 24 Installation AV Out Setup - The TV has a special signal output capability which allows you to hook up a second TV or monitor. AUDIO (MONO) S-VIDEO VIDEO AUDIO AV V OUT AV V IN 1 OPTICAL PTICAL DIGITAL AUDIO DIGITAL OUT COMPONENT IN VIDEO Connect the second TV or monitor to the TV’s AV OUT jacks. See the Operating Manual of the second TV or monitor for further details regarding that device’s input settings. 1/2 • Component 1-2, RGB-PC, HDMI1/DVI, HDMI2, DTV input sources cannot be used for Monitor out. • We recommend to use the video and audio output jacks for VCR recording. S-VIDEO IN (R) AUDIO (L) VIDEO Digital Audio Output - Send the TV’s audio to external audio equipment (stereo system) via the Digital Audio Output Optical port. AUDIO 1/2 (MONO) S-VIDEO VIDEO AUDIO AV V OUT AV V IN 1 OPTICAL PTICAL DIGITAL AUDIO DIGITAL OUT COMPONENT IN VIDEO Connect one end of an optical cable to the TV Digital Audio Optical Output port. Connect the other end of the optical cable to the digital audio optical input on the audio equipment. See the external audio equipment instruction manual for operation. When connecting with external audio equipments, such as amplifiers or speakers, please turn the TV speakers off. (Refer to p.43) CAUTION Do not look into the optical output port. Looking at the laser beam may damage your vision. 25 RGB IN (PC) AUDIO IN (RGB/DVI) REMOTE CONTROL IN Installation RS-232C IN (CONTROL & SERVICE) PC Setup - This TV provides Plug and Play capability, meaning that the PC adjusts automatically to the TV's settings. When connecting with a D-sub 15 pin cable RGB IN (PC) AUDIO IN (RGB/DVI) Connect the RGB output of the PC to the RGB IN (PC) jack on the set. Connect the PC audio outputs to the AUDIO IN(RGB/DVI) jack on the set. Turn on the PC and the set. Select RGB-PC input source with using the INPUT button on the remote control. REMOTE CONTROL IN RS-232C IN (CONTROL & SERVICE) SERVICE) (R) AUDIO (L) RGB-PC OUTPUT PC When connecting with a HDMI to DVI cable SERVICE RGB IN (PC) AUDIO IN (RGB/DVI) HDMI IN REMOTE CONTROL IN 1(DVI) RS-232C IN (CONTROL & SERVICE) DVI-PC OUTPUT (R) AUDIO (L) PC Connect the DVI output of the PC to the HDMI IN 1(DVI) jack on the set. Connect the audio outputs of the PC to the AUDIO IN(RGB/DVI) jack on the set. Turn on the PC and the set. Select HDMI1/DVI input source with using the INPUT button on the remote control. RGB IN (PC) AUDIO IN (RGB/DVI) REMOTE CONTROL IN • If the PC has a DVI output and no HDMI output, a separated audio connection is necessary. • If the PC does not support Auto DVI, you need to set the output resolution appropriately. To get the best picture quality, adjust the output resolution of PC graphics card's output resolution to 1024x768, 60Hz. RS-232C IN (CONTROL & SERVICE) 26 Installation 1. Depending on the graphics card, DOS mode may not work if a HDMI to DVI Cable is in use. 2. When Source Devices connected with HDMI/DVI Input, output PC Resolution (VGA, SVGA, XGA, WXGA), Position and Size may not fit to Screen.Press the ADJUST button to adjust the screen Position of TV SET and contact an PC graphics card service center. 3. When Source Devices connected with HDMI/DVI Input, output TV SET Resolution (480p, 720p, 1080i. 1080p) and TV SET Display fit EIA/CEA861-B Specification to Screen. If not, refer to the Manual of HDMI/DVI Source Devices or contact your service center. 4. In case HDMI/DVI Source Devices is not connected Cable or poor cable connection, "NO SIGNAL" OSD display in HDMI/DVI Input. In case that Video Resolution is not supported TV SET output in HDMI/DVI Source Devices, "INVALID FORMAT" OSD display. Refer to the Manual of HDMI/DVI Source Devices or contact your service center. 5. Check the image on your TV. There may be noise associated with the resolution, vertical pattern, contrast or brightness in PC, HDMI/DVI mode. If noise is present, change the PC or HDMI/DVI mode to another resolution, change the refresh rate to another rate or adjust the brightness and contrast on the menu until the picture is clear. If the refresh rate of the PC graphic card can not be changed, change the PC graphic card or consult the manufacturer of the PC graphic card. 6. Avoid keeping a fixed image on the TV's screen for a long period of time. The fixed image may become permanently imprinted on the screen. 7. The synchronization input form for Horizontal and Vertical frequencies is separate. Supported Display Resolution (RGB-PC, HDMI1/DVI, HDMI2 Mode) Resolution Horizontal Frequency (kHz) Vertical Frequency (Hz) Resolution Horizontal Frequency (kHz) Vertical Frequency (Hz) 640x350 31.468 70.08 1280x768 47.776 59.87 640x480 31.469 59.94 59.80 31.469 70.08 1360x768 1366x768 47.720 720x400 47.130 59.65 31.469 59.94 33.716 59.94 31.500 60.00 33.750 60.00 800x600 37.879 60.31 27.000 24.00 1024x768 48.363 60.00 33.750 30.00 44.955 59.94 45.000 60.00 * 720x480 *1280x720 *1920x1080i *1920x1080p * This format is only for HDMI-DTV input. • 42PC3DVU is not supported to 1280x768, 1360x768, 1366x768, 1920x1080P. 27 Installation Screen Setup for PC mode - When RGB connect to PC input and select the RGB-PC, this function is used. - When HDMI/DVI connect to PC input and select HDMI/DVI input, this function is used. - After connecting RGB-PC or HDMI/DVI to PC input and checking the screen quality. * Adjustment for screen Resolution, Position, Size, and Phase FLASHBK EZ PIC EZ SOUND SAP CC ADJUST ADJUST Press the ADJUST button and then use D Resolution, POSITION, SIZE, or PHASE. Press ENTER button and then use make appropriate adjustments. Mini Glossary Position This function is to adjust picture to left/right and up/down as you prefer. Size Phase This function is to minimize any vertical bars or stripes visible on the screen background. And the horizontal screen size will also change. This function allows you to remove any horizontal noise and clear or sharpen the image of characters. /E button to select D /E /F /G buttons to • The PHASE adjustment range is -16 ~ +16. (In HDMI/DVI-PC mode, PHASE is not available.) • The SIZE adjustment range is -30 ~ +30. (In HDMI/DVI-PC mode, SIZE is not available.) Press ENTER button. * When you change the resolution, select the proper resolution in present input to see the best picture appearance. Resolution This function allows you select Resolution of XGA/WXGA. * Initializing (Reset to original factory values) FLASHBK EZ PIC EZ SOUND SAP CC ADJUST ADJUST - To initialize the adjusted values 28 Press the ADJUST button and then use the RESET option. Press ENTER button and then use Press ENTER button. F /G D /E button to select button to select Yes. Operation Operation Basic operation Turning on the TV 1. First, connect power cord correctly. At this moment, the TV switches to standby mode. In standby mode to turn TV on, press the , INPUT, CH D / E button on the TV or press the POWER, TV INPUT, INPUT, CH D / E, Number (0 ~ 9) button on the remote control . 2. Select the viewing source by using TV INPUT, INPUT button on the remote control. This TV is programmed to remember which power state it was last set to, even if the power cord is out. 3. When finished using the TV, press the POWER button on the remote control. The TV reverts to standby mode. Volume Adjustment D / E button to adjust the volume. 2. If you want to switch the sound off, press the MUTE button. 1. Press the VOL 3. You can cancel this function by pressing the MUTE or VOL button. Channel Selection Press the CH or NUMBER buttons to select a channel number. • If you intend to be away on vacation, disconnect the power plug from the wall power outlet. On Screen Menus Language Selection Aspect Ratio Aspect Ratio Caption/Text Caption/Text Caption Option Caption Option Language Language ISM Method ISM Method Low Power Low Power - The menus can be shown on the screen in the selected language. First select your language. Press the MENU button and then use OPTION menu. Press the button and then use English Español (Spanish) Français (French) button to select the button to select Language. Press the G button and then use D / E button to select your desired language. From this point on, the on-screen menus will be shown in the selected language. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. 29 Operation On Screen Menus Selection and Adjustment How to adjust the OSD screen 1. Press the MENU button and then 2. Press the G button and then use D /E /F /G button to select each menu. button to display the available menus. EZ Scan EZ Picture Manual Scan Color Temperature Channel Edit XD DTV Signal Advanced Input Source Video Reset Input Label Set ID Lock System Set Password Block Channel Movie Rating TV Rating-Children TV Rating-General Input Block Audio Language Aspect Ratio Auto Clock Caption/Text Manual Clock Caption Option Off Timer Language On Timer ISM Method Sleep Timer Low Power Auto Off EZ Sound Balance TV Speaker • Your TV's OSD (On Screen Display) may differ slightly from what is shown in this manual. 30 Operation Setup Menu Options EZ Scan (Channel Search) EZ Scan EZ Scan Manual Scan Manual Scan Channel Edit Channel Edit DTV Signal DTV Signal Input Source Input Source Input Label Input Label Set ID Set ID Selection ( G or leads you to the EZ scan screen. Processing EZ scan... TV Ch.20 0 channel(s) found Press to stop the current scan and start DIGITAL ANTENNA channel scan. Next - Automatically finds all channels available through antenna or cable inputs, and stores them in memory on the channel list. - Run EZ Scan again after any Antenna/Cable connection changes. - A password is required to gain access to EZ Scan menu if the Lock System is turned on. MENU Previous Press the MENU button and then use D / E button to select the SETUP menu. Press the G button and then use D /E button to select EZ Scan. Press the ENTER button to begin the channel search. Allow EZ Scan to complete the channel search cycle for ANTENNA, and CABLE. Manual Scan EZ Scan EZ Scan Manual Scan Manual Scan Channel Edit Channel Edit DTV Signal DTV Signal Input Source Input Source Input Label Input Label Set ID Set ID Select channel type and RF-channel number. TV TV 2-0 Press to delete the channel. - A password is required to gain access to Manual Scan menu if the Lock System is turned on. Press the MENU button and then use D / E button to select the SETUP menu. Press the G button and then use ber you want to add or delete. Press the ENTER button to add or delete for the channel number. Press the G button and then use D /E button to select Manual Scan. Press the G button and then use D and CADTV. /E button to select TV, DTV, CATV, D /E button to select channel num- Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. 31
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Page Count : 15 XMP Toolkit : XMP toolkit 2.9.1-13, framework 1.6 About : uuid:9e87c53f-e00f-4273-a64a-f199395f9933 Modify Date : 2006:08:14 15:27:20+09:00 Create Date : 2006:08:14 15:27:13+09:00 Metadata Date : 2006:08:14 15:27:20+09:00 Document ID : uuid:ac0404c1-f256-4226-89c4-1ff7224e12d0 Format : application/pdf Title : 38289U0527F(LG) -PDP Creator : QuarkXPressª3.3E: LaserWriter 8 Z1-8.7.1 Author : PSY Producer : Acrobat Distiller 4.0 for MacintoshEXIF Metadata provided by EXIF.tools