LG Electronics USA 47LH50UC LCD TV MONITOR User Manual User s Manual H ok

LG Electronics USA LCD TV MONITOR User s Manual H ok

Users Manual

Order Number : GETEC-C1-09-083 FCC Class B Certification Test Report Number : GETEC-E3-09-036 Page 1 / 1 EUT Type: LCD TV/Monitor FCC ID.: BEJ47LH50UC APPENDIX H : USER’S MANUAL
Please read this manual carefully before operatingyour set. Retain it for future reference.Record model number and serial number of the set. See the label attached on the back cover and quote this information to your dealer when you require service.LCD TVOWNER’S MANUAL42LH5047LH50P/NO : SAC30708033 (0901-REV02)www.lgusa.com / www.lg.caModel:Serial:
2WARNING / CAUTIONWARNING / CAUTIONTo prevent fire or shock hazards, do not exposethis product to rain or moisture.FCC NOTICEClass B digital deviceThis equipment has been tested and found to complywith the limits for a Class B digital device, pursuant toPart 15 of the FCC Rules. These limits are designedto provide reasonable protection against harmfulinterference in a residential installation. This equipmentgenerates, uses and can radiate radio frequency energyand, if not installed and used in accordance with theinstructions, may cause harmful interference to radiocommunications. However, there is no guarantee thatinterference will not occur in a particular installation.If this equipment does cause harmful interference toradio or television reception, which can be determinedby turning the equipment off and on, the user isencouraged to try to correct the interference by oneor more of the following measures:- Reorient or relocate the receiving antenna.- Increase the separation between the equipment andreceiver.- Connect the equipment to an outlet on a circuitdifferent from that to which the receiver is connected.- Consult the dealer or an experienced radio/TVtechnician for help.Any changes or modifications not expressly approvedby the party responsible for compliance could voidthe user’s authority to operate the equipment.CAUTIONDo not attempt to modify this product in any waywithout written authorization from LG Electronics.Unauthorized modification could void the user’sauthority to operate this product The lightning flash with arrowheadsymbol, within an equilateral triangle, isintended to alert the user to the presenceof uninsulated “dangerous voltage” within theproduct’s enclosure that may be of sufficientmagnitude to constitute a risk of electric shock topersons.The exclamation point within an equilateraltriangle is intended to alert the user tothe presence of important operating andmaintenance (servicing) instructions in the litera-ture accompanying the appliance.TO REDUCE THE RISK OF ELECTRIC SHOCKDO NOT REMOVE COVER (OR BACK). NOUSER SERVICEABLE PARTS INSIDE. REFER TOQUALIFIED SERVICE PERSONNEL.WARNING/CAUTIONTO REDUCE THE RISK OF FIRE AND ELECTRICSHOCK, DO NOT EXPOSE THIS PRODUCT TORAIN OR MOISTURE.NOTE TO CABLE/TV INSTALLERThis reminder is provided to call the CATV systeminstaller’s attention to Article 820-40 of the NationalElectric Code (U.S.A.). The code provides guidelines forproper grounding and, in particular, specifies that thecable ground shall be connected to the grounding systemof the building, as close to the point of the cable entryas practical.
3IMPORTANT SAFETY INSTRUCTIONSSAFETY INSTRUCTIONSRead these instructions.Keep these instructions.Heed all warnings.Follow all instructions.Do not use this apparatus near water.Clean only with dry cloth.Do not block any ventilation openings. Install inaccordance with the manufacturer’s instructions.Do not install near any heat sources such asradiators, heat registers, stoves, or otherapparatus (including amplifiers)that produceheat.Do not defeat the safety purpose of the polarizedor grounding-type plug. A polarized plug hastwo blades with one wider than the other. Agrounding type plug has two blades and athird grounding prong, The wide blade or thethird prong are provided for your safety. If theprovided plug does not fit into your outlet,consult an electrician for replacement of theobsolete outlet.Protect the power cord from being walked onor pinched particularly at plugs, conveniencereceptacles, and the point where they exit fromthe apparatus.Only use attachments/accessories specified bythe manufacturer.Use only with the cart, stand, tripod, bracket,or table specified by the manufacturer, or soldwith the apparatus. When a cart is used, usecaution when moving the cart/apparatus com-bination to avoid injury from tip-over.Unplug this apparatus during lighting stormsor when unused for long periods of time.Refer all servicing to qualified service personnel.Servicing is required when the apparatus hasbeen damaged in any way, such as power-supply cord or plug is damaged, liquid hasbeen spilled or objects have fallen into theapparatus, the apparatus has been exposed torain or moisture, does not operate normally, orhas been dropped.12345786910
4SAFETY INSTRUCTIONSNever touch this apparatus or antenna duringa thunder or lighting storm. When mounting a TV on the wall, make surenot to install the TV by the hanging power andsignal cables on the back of the TV.Do not allow an impact shock or any objects tofall into the product, and do not drop onto thescreen with something.CAUTION concerning the Power Cord:It is recommend that appliances be placedupon a dedicated circuit; that is, a singleoutlet circuit which powers only that applianceand has no additional outlets or branchcircuits. Check the specification page of thisowner's manual to be certain.Do not connect too many appliances to thesame AC power outlet as this could result infire or electric shock.Do not overload wall outlets. Overloaded walloutlets, loose or damaged wall outlets, extensioncords, frayed power cords, or damaged orcracked wire insulation are dangerous. Any ofthese conditions could result in electric shockor fire. Periodically examine the cord of yourappliance, and if its appearance indicates damageor deterioration, unplug it, discontinue use ofthe appliance, and have the cord replaced withan exact replacement part by an authorizedservicer. Protect the power cord from physicalor mechanical abuse, such as being twisted,kinked, pinched, closed in a door, or walkedupon. Pay particular attention to plugs, walloutlets, and the point where the cord exits theappliance. Do not make the TV with the power cordplugged in. Do not use a damaged or loosepower cord. Be sure do grasp the plug whenunplugging the power cord. Do not pull on thepower cord to unplug the TV. WARNING - To reduce the risk of fire or electricalshock, do not expose this product to rain,moisture or other liquids. Do not touch the TVwith wet hands. Do not install this productnear flammable objects such as gasoline orcandles or expose the TV to direct airconditioning. Do not expose to dripping or splashing and donot place objects filled with liquids, such asvases, cups, etc. on or over the apparatus (e.g.on shelves above the unit).GGRROOUUNNDDIINNGGEnsure that you connect the earth ground wireto prevent possible electric shock (i.e. a TVwith a three-prong grounded AC plug must beconnected to a three-prong grounded AC out-let). If grounding methods are not possible,have a qualified electrician install a separatecircuit breaker. Do not try to ground the unit by connecting itto telephone wires, lightening rods, or gaspipes.DDIISSCCOONNNNEECCTTIINNGG DDEEVVIICCEE FFRROOMM MMAAIINNSSMains plug is the disconnecting device. Theplug must remain readily operable.Keep the product away from direct sunlight.1211141316171819Power SupplyShort-circuitBreaker15
5AANNTTEENNNNAASSOOuuttddoooorr aanntteennnnaa ggrroouunnddiinnggIf an outdoor antenna is installed, follow theprecautions below. An outdoor antenna systemshould not be located in the vicinity of over-head power lines or other electric light orpower circuits, or where it can come in contactwith such power lines or circuits as death orserious injury can occur.Be sure the antenna system is grounded so asto provide some protection against voltagesurges and built-up static charges. Section 810 of the National Electrical Code(NEC) in the U.S.A. provides information withrespect to proper grounding of the mast andsupporting structure, grounding of the lead-inwire to an antenna discharge unit, size ofgrounding conductors, location of antenna dis-charge unit, connection to grounding elec-trodes and requirements for the groundingelectrode. AAnntteennnnaa ggrroouunnddiinngg aaccccoorrddiinngg ttoo tthheeNNaattiioonnaall EElleeccttrriiccaall CCooddee,, AANNSSII//NNFFPPAA 7700CClleeaanniinnggWhen cleaning, unplug the power cord andscrub gently with a soft cloth to preventscratching. Do not spray water or other liquidsdirectly on the TV as electric shock may occur.Do not clean with chemicals such as alcohol,thinners or benzene. MMoovviinnggMake sure the product is turned off,unplugged and all cables have been removed. Itmay take 2 or more people to carry larger TVs.Do not press against or put stress on the frontpanel of the TV. VVeennttiillaattiioonnInstall your TV where there is proper ventila-tion. Do not install in a confined space such asa bookcase. Do not cover the product withcloth or other materials (e.g.) plastic whileplugged in. Do not install in excessively dustyplaces. If you smell smoke or other odors coming fromthe TV or hear strange sounds, unplug the powercord contact an authorized service center.Do not press strongly upon the panel withhand or sharp object such as nail, pencil orpen, or make a scratch on it.222023242521Antenna Lead in WireAntenna Discharge Unit(NEC Section 810-20)Grounding Conductor(NEC Section 810-21)Ground ClampsPower Service GroundingElectrode System (NECArt 250, Part H)Ground ClampElectric ServiceEquipmentNEC: National Electrical Code
6CONTENTSWARNING / CAUTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . 3FEATURE OF THIS TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8PREPARATIONAccessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Front Panel Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10Back Panel Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11Stand Instruction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12VESA Wall Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13Cable Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14Desktop Pedestal Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15Swivel Stand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15Attaching the TV to a Desk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15Securing the TV to the wall to prevent falling whenthe TV is used on a stand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16Antenna or Cable Connection . . . . . . . . . . . . . . . . . . . . . . . . . . 17EXTERNAL EQUIPMENT SETUPHD Receiver Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18DVD Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21VCR Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23Other A/V Source Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25PC Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26USB Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32Audio Out Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33WATCHING TV / CHANNEL CONTROLRemote Control Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34Turning On the TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36Channel Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36Volume Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36Quick Menu / Favorite Channel Setup . . . . . . . . . . . . . . 37Initial Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38On-Screen Menus Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39Channel Setup - Auto Scan (Auto Tuning) . . . . . . . . . . . . . . . . . . . . . . . . . . . 40- Add / Delete Channel (Manual Tuning) . . . . . . 41- Channel Editing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42Input List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43Input Label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44AV Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45SIMPLINK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46USBEntry Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48Photo List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49Music List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53PICTURE CONTROLPicture Size (Aspect Ratio) Control . . . . . . . . . . . . . . . . . . 56Preset Picture Settings- Picture Mode - Preset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58- Color Tone - Preset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59Manual Picture Adjustment- Picture Mode - User Mode . . . . . . . . . . . . . . . . . . . . . . . . 60- Picture Mode - Expert Control . . . . . . . . . . . . . . . . . . . 61Picture Improvement Technology . . . . . . . . . . . . . . . . . . . . . 62Advanced Control - Black (Darkness) Level . . . . . . . 63Advanced Control - Eye Care . . . . . . . . . . . . . . . . . . . . . . . . . . . 64Advanced Control - Real Cinema . . . . . . . . . . . . . . . . . . . . . . 65Picture Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66Power Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
7SOUND & LANGUAGE CONTROLAuto Volume Leveler (Auto Volume) . . . . . . . . . . . . . . . . . 68Preset Sound Settings (Sound Mode) . . . . . . . . . . . . . . 69Sound Setting Adjustment - User Mode . . . . . . . . . . . 70Clear Voice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71Balance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72TV Speakers On/Off Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73Audio Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74Stereo/SAP Broadcast Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . 75Audio Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76On-Screen Menus Language Selection . . . . . . . . . . . . . . 77Caption Mode- Analog Broadcasting System Captions . . . . . . . 78- Digital Broadcasting System Captions . . . . . . . . 79- Caption Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80TIME SETTINGClock Setting- Auto Clock Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81- Manual Clock Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82Auto On/Off Time Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83Sleep Timer Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84Auto Shut-off Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85PARENTAL CONTROL / RATINGSSet Password & Lock System . . . . . . . . . . . . . . . . . . . . . . . . . . . 86Channel Blocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89Movie & TV Rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90Downloadable Rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95External Input Blocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96Key lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97APPENDIXTroubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 0Product Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101Programming the Remote Control . . . . . . . . . . . . . . . . . 102IR Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .105External Control Through RS-232C . . . . . . . . . . . . . . . . .107
8FEATURE OF THIS TVis a trademark of SRS Labs, Inc.TruSurround XT technology is incorporated underlicense from SRS Labs, Inc.Manufactured under license from Dolby Laboratories.“Dolby“and the double-D symbol are trademarks ofDolby Laboratories. FOR LCD TV■If the TV feels cold to the touch, there may be a small “flicker” when it is turned on. This is normal, there isnothing wrong with TV.■Some minute dot defects may be visible on the screen, appearing as tiny red, green, or blue spots. However, theyhave no adverse effect on the monitor's performance.■Avoid touching the LCD screen or holding your finger(s) against it for long periods of time. Doing so may producesome temporary distortion effects on the screen.On Disposal (Only Hg lamp used LCD TV)The fluorescent lamp used in this product contains a small amount of mercury. Do not dispose of this product withgeneral household waste. Disposal of this product must be carried out in accordance to the regulations of your localauthority.CALIBRATE LIKE A PRO: Sophisticated and detailedcalibrations can be made through the ISFccc mode.Detailed calibration requires a licensed technician.Please contact your local dealer to inquire about anISF certified technician.
PREPARATION9PREPARATIONACCESSORIESEnsure that the following accessories are included with your TV. If an accessory is missing, please contact thedealer where you purchased the TV. The accessories included may differ from the images below.OOppttiioonn EExxttrraass* Wipe spots on the exterior only withthe polishing cloth.* Do not wipe roughly when removingstain. Excessive pressure may causescratch or discoloration.Polishing Cloth(This feature is not availablefor all models.)Copyright© 2007 LGE,All Rights Reserved.D-sub 15 pin Cable1.5V 1.5VOwner’s Manual Power CordRemote Control,BatteriesINPUTFAVMUTETVSTBPOWERQ. MENUMENUAV MODERETURNENTERVOLCH1234567809FLASHBKPAGEDVDVCRCD ManualWhen using the VGA (D-sub 15 pincable) PC connection, the usermust use shielded signal interfacecables with ferrite cores to maintainstandards compliance.Protection CoverorProtective Bracket and Bolt forPower Cord (This feature is not available for all models.)(Refer to P.14)OOnnllyy 3377//4422LLGG55**Bolts for stand assembly(Refer to P.12) Screw for stand fixing(Refer to P.15)x 4 x 4
PREPARATION10FRONT PANEL INFORMATIONPREPARATION■Image shown may differ from your TV.■NOTE: If your TV has a protection tape attached, remove the tape.And then wipe the TV with a cloth (If a polishing cloth is included with your TV, use it).POWER ButtonPower/Standby IndicatorIlluminates red in standby mode.Illuminates blue when the set is switched on.(Can be adjusted using PPoowweerr IInnddiiccaattoorrinthe OPTION menu. GGpp..6677)CHVOLMENUINPUTENTERCHANNEL ( , ) ButtonsVOLUME (+, -) ButtonsENTER ButtonMENU ButtonINPUT ButtonIntelligent SensorAdjusts picture according to thesurrounding conditions Remote Control Sensor
PREPARATION11BACK PANEL INFORMATION■Image shown may differ from your TV.AV IN 2L/MONORAUDIOVIDEOHDMI IN 3 USB IN( )RGB INCOMPONENT INAUDIO(RGB/DVI)RGB(PC)REMOTECONTROL INANTENNA/CABLE IN12RS-232C IN(CONTROL & SERVICE)VIDEOAUDIOOPTICAL COAXIALDIGITAL AUDIO OUTAUDIO OUTAV IN 1RHDMI/DVI IN 21VIDEOMONO( )AUDIOS-VIDEO1346782951R( )11HDMI/DVI IN, HDMI INDigital Connection. Supports HD video and Digital audio. Doesn’tsupport 480i. Accepts DVI video using an adapter or HDMI toDVI cable (not included).COMPONENT INAnalog Connection. Supports HD. Uses a red, green, and blue cable for video & redand white for audio.RGB (PC)Analog PC Connection. Uses a D-sub 15 pin cable(VGA cable).AUDIO (RGB/DVI)1/8” headphone jack for analog PC audio input.REMOTE CONTROL IN PORTFor a wired remote control.RS-232C IN (CONTROL & SERVICE) PORTUsed by third party devices.ANTENNA/CABLE INConnect over-the air signals to this jack.Connect cable signals to this jack.DIGITAL AUDIO OUTDigital audio output for use with amps and hometheater systems. Includes an optical and coaxial connection.Note: In standby mode, these ports do not work.AUDIO OUTAnalog audio output for use with amps and hometheater systems.AV (Audio/Video) INAnalog composite connection. Supports standarddefinition video only (480i).S-VIDEOBetter quality than standard composition.Supports standard definition video only (480i).USB INPUTUsed for viewing photos and listening to MP3s.Power Cord SocketFor operation with AC power. Caution: Never attempt to operate the TV on DCpower.1234569101178109(Except42/47/52LG50DC)
PREPARATION12STAND INSTRUCTIONPREPARATION■Image shown may differ from your TV.Assemble the parts of the SSTTAANNDD BBOODDYYwith CCOOVVEERR BBAASSEEof the TV.2Assemble the TV as shown.3Fix the 4 bolts securely using the holes in theback of the TV.4SSTTAANNDD BBOODDYYCCOOVVEERR BBAASSEECarefully place the TV screen side down on a cush-ioned surface to protect the screen from damage.1INSTALLATION(Only 37/42LG5*)DETACHMENTCarefully place the TV screen side down on acushioned surface to protect the screen fromdamage.1Loose the bolts from TV.2Detach the stand from TV.3After removing the stand, install the includedpprrootteeccttiioonn ccoovveerrover the hole for the stand.Press the PPRROOTTEECCTTIIOONN CCOOVVEERRinto the TVuntil you hear it click.PROTECTION COVERGGWhen assembling the desk type stand, make surethe bolt is fully tightened (If not tightened fully,the TV can tilt forward after the product installa-tion). Do not over tighten.NOTE!
PREPARATION13VESA WALL MOUNTINGInstall your wall mount on a solid wall perpendicular to the floor. When attaching to other building materials, pleasecontact your nearest dealer.If installed on a ceiling or slanted wall, it may fall and result in severe personal injury.We recommend that you use an LG brand wall mount when mounting the TV to a wall.LG recommends that wall mounting be performed by a qualified professional installer.GGDo not install your wall mount kit while your TV is turned on. It may result in personal injury due to electricshock.CAUTIONGGScrew length needed depends on the wall mountused. For further information, refer to the instruc-tions included with the mount.GGStandard dimensions for wall mount kits are shownin the table.GGWhen purchasing our wall mount kit, a detailedinstallation manual and all parts necessary forassembly are provided.GGDo not use screws longer then the standard dimen-sion, as they may cause damage to the inside tothe TV.GGFor wall mounts that do not comply with the VESAstandard screw specifications, the length of thescrews may differ depending on their specifica-tions.GGDo not use screws that do not comply with theVESA standard screw specifications.Do not use fasten the screws too strongly, this maydamage the TV or cause the TV to a fall, leading topersonal injury. LG is not liable for these kinds ofaccidents.GGLG is not liable for TV damage or personal injurywhen a non-VESA or non specified wall mount isused or the consumer fails to follow the TV installa-tion instructions.NOTE!AABBProduct Model VESA(A *B) Standard Screw Quantity37LG5*42LG5*47LG5*52LG5*200 * 200800 * 400M6M644LCD TV
PREPARATION14CABLE MANAGEMENTPREPARATIONConnect the cables as necessary.To connect additional equipment, see theEXTERNAL EQUIPMENT SETUP section.Secure the power cable with the PROTECTIVEBRACKET and the screw as shown. It will helpprevent the power cable from being removedby accident.Install the CABLE MANAGEMENT CLIP asshown.CABLE MANAGEMENT CLIPPROTECTIVE BRACKET(This feature is not available for all models.)12Put the cables inside the CABLE MANAGEMENTCLIP and snap it closed.3■Image shown may differ from your TV.
PREPARATION15DESKTOP PEDESTAL INSTALLATIONFor proper ventilation, allow a clearance of 4 inches on all four sides from the wall.■Image shown may differ from your TV.4 inches4 inches4 inches 4 inchesSWIVEL STANDAfter installing the TV, you can adjust the TV set manually to the left or right direction by 20 degrees to suityour viewing position.GGEnsure adequate ventilation by following the clearance recommendations.GGDo not mount near or above any type of heat source.CAUTIONATTACHING THE TV TO A DESK (Only 37/42LG5*)The TV must be attached to a desk so it cannot be pulled in a forward/backward direction, potentially causinginjury or damaging the product. GGTo prevent TV from falling over, the TV should be securely attached to the floor/wall per installationinstructions. Tipping, shaking, or rocking the machine may cause injury.WARNING1-Screw(provided as parts of the product)DeskStand
We recommend that you set up the TV close to a wall so it cannot fall over if pushed backwards. Additionally, we recommend that the TV be attached to a wall so it cannot be pulled in a forward direction,potentially causing injury or damaging the product. Caution: Please make sure that children don’t climb on or hang from the TV. ■Insert the eye-bolts (or TV brackets and bolts) to tighten the product to the wall as shown in the picture. *If your product has the bolts in the eye-bolts position before inserting the eye-bolts, loosen the bolts. * Insert the eye-bolts or TV brackets/bolts and tighten them securely in the upper holes.Secure the wall brackets with the bolts (sold separately) to the wall. Match the height of the bracket that ismounted on the wall to the holes in the product. Ensure the eye-bolts or brackets are tightened securely.■Use a sturdy rope (sold separately) to tie the product. It is safer to tiethe rope so it becomes horizontal between the wall and the product.■You should purchase necessary components to prevent TV from falling off of the stand.■Image shown may differ from your TV.GGUse a platform or cabinet strong enough and large enough to support the size and weight of the TV.GGTo use the TV safely make sure that the height of the bracket on the wall and the one on the TV are the same.NOTE!PREPARATION16SECURING THE TV TO THE WALL TO PREVENT FALLINGWHEN THE TV IS USED ON A STANDPREPARATION
PREPARATION17ANTENNA OR CABLE CONNECTION1. Antenna (Analog or Digital)Wall Antenna Socket or Outdoor Antenna without a Cable BoxConnection.For optimum picture quality, adjust the antenna direction if needed.2. CableWallAntennaSocketOutdoorAntenna(VHF, UHF)Cable TVWall JackMulti-family Dwellings/Apartments(Connect to wall antenna socket)RF Coaxial Wire (75 ohm)RF Coaxial Wire (75 ohm)Single-family Dwellings /Houses(Connect to wall jack for outdoor antenna)Be careful not to bend the copper wirewhen connecting the antenna.Copper Wire■To improve the picture quality in a poor signal area, please purchase a signal amplifier and install properly. ■If the antenna needs to be split for two TV’s, install a 2-Way Signal Splitter.■If the antenna is not installed properly, contact your dealer for assistance.ANTENNA/CABLE INR( )ANTENNA/CABLE INR( )■To prevent damage do not connect to the power outlet until all connections are made between the devices.
EXTERNAL EQUIPMENT SETUP18HD RECEIVER SETUPEXTERNAL EQUIPMENT SETUPThis TV can receive digital over-the-air/digital cable signals without an external digital set-top box. However, ifyou do receive digital signals from a digital set-top box or other digital external device.Component Connection1. How to connectConnect the video outputs (Y, PB, PR)of the digital set-top box to the CCOOMMPPOONNEENNTT IINN VVIIDDEEOO 11jacks onthe TV. Match the jack colors (Y = green, PB= blue, andPR= red).Connect the audio output of the digital set-top box to the CCOOMMPPOONNEENNTT IINN AAUUDDIIOO 11jacks on the TV.212. How to use■Turn on the digital set-top box. (Refer to the owner’s manual for the digital set-top box. operation)■Select the CCoommppoonneenntt11input source on the TV usingthe IINNPPUUTTbutton on the remote control.■If connected to CCOOMMPPOONNEENNTT IINN22input, select theCCoommppoonneenntt 22input source on the TV.■To prevent the equipment damage, never plug in any power cords until you have finished connecting all equipment.■Image shown may differ from your TV.Y, CB/PB, CR/PRSupported ResolutionsHorizontal Vertical Frequency(KHz)Frequency(Hz)15.73 59.9415.73 60.0031.47 59.9431.50 60.0044.96 59.9445.00 60.0033.72 59.9433.75 60.0026.97 23.97627.00 24.0033.71 29.9733.75 30.0067.432 59.9467.50 60.00Resolution 720x480i720x480p1280x720p1920x1080i1920x1080pSignal480i480p720p1080 i1080 pComponentYesYesYesYesYesHDMINoYesYesYesYesRGB INAUDIO(RGB/DVI)RGB(PC)REMOTECONTROL (CDVI IN COMPONENT IN12VIDEOLYPBPRRAUDIOY L RPBPR12
EXTERNAL EQUIPMENT SETUP19HDMI ConnectionConnect the digital set-top box to HHDDMMII//DDVVII IINN11,22, or 33* jack on the TV.No separate audio connection is necessary.HDMI supports both audio and video.1. How to connect2. How to use■Turn on the digital set-top box. (Refer to the owner’s manual for the digital set-top box.)■Select the HHDDMMII11,HHDDMMII22,orHHDDMMII33* input source on theTV using the IINNPPUUTTbutton on the remote control.21HDMI-DTVHorizontal Vertical Frequency(KHz)Frequency(Hz)31.47 59.9431.50 60.0044.96 59.9445.00 60.0033.72 59.9433.75 60.0026.97 23.97627.00 24.0033.71 29.9733.75 30.0067.432 59.93967.50 60.00Resolution 720x480p1280x720p1920x1080i1920x1080pRGB INCOMPONENT A(RGRGB(PC)12VIDEOYPBPRHDMI/DVI IN 21HDMI-DTV OUTPUT1* HDMI 3: Except 42/47/52LG50DC
EXTERNAL EQUIPMENT SETUP20EXTERNAL EQUIPMENT SETUPConnect the DVI output of the digital set-top box tothe HHDDMMII//DDVVII IINN 11, 22, or 33* jack on the TV.Connect the PC audio output to the AAUUDDIIOO((RRGGBB//DDVVII))jack on the TV.1. How to connect2. How to use■Turn on the digital set-top box. (Refer to the owner’s manu-al for the digital set-top box.)■Select the HHDDMMII11,HHDDMMII22,orHHDDMMII33* input source on theTV using the IINNPPUUTTbutton on the remote control.21DVI to HDMI ConnectionGGA DVI to HDMI cable or adapter is required for thisconnection. DVI doesn't support audio, so a separateaudio connection is necessary.NOTE!RGB INCOMPONENT INAUDIO(RGB/DVI)RGB(PC)REMOCONTRO12VIDEOLYPBPRRAUDIOHDMI/DVI IN 21L RDVI-DTV OUTPUT12* HDMI 3: Except 42/47/52LG50DC
EXTERNAL EQUIPMENT SETUP21DVD SETUPComponent ConnectionComponent Input portsTo get better picture quality, connect a DVD player to the component input ports as shown below.Component ports on the TVYPBPRVideo output ports on DVD playerYYYYPBB-YCbPbPRR-YCrPrConnect the video outputs (Y, PB, PR)of the DVD to theCCOOMMPPOONNEENNTT IINN VVIIDDEEOO11jacks on the TV.Match the jack colors (Y = green, PB= blue, and PR= red).Connect the audio outputs of the DVD to the CCOOMMPPOONNEENNTT IINN AAUUDDIIOO11jacks on the TV.1. How to connect2. How to use■Turn on the DVD player, insert a DVD.■Select the CCoommppoonneenntt11input source on the TV usingthe IINNPPUUTTbutton on the remote control.■If connected to CCOOMMPPOONNEENNTT IINN 22input, select theCCoommppoonneenntt 22input source on the TV.■Refer to the DVD player's manual for operating instructions.21RGB INAUDIO(RGB/DVI)RGB(PC)REMOTCONTROL(VI IN COMPONENT IN12VIDEOLYPBPRRAUDIOY L RPBPR1 2
EXTERNAL EQUIPMENT SETUP22EXTERNAL EQUIPMENT SETUPS-Video ConnectionNDIOB/DVI)REMOTECONTROL INANTENNA/CABLE INRS-232C IN(CONTROL & SERVICE)L RAUDIOOPTICAL COAXIALDIGITAL AUDIO OUTL RS-VIDEOAUDIOAUDIO OUTAV IN 1VIDEO LR(MONO)AUDIOS-VIDEO12Connect the S-VIDEO output of the DVD to theSS--VVIIDDEEOOinput on the TV.Connect the audio outputs of the DVD to the AAUUDDIIOOinput jacks on the TV.1. How to connect2. How to use■Turn on the DVD player, insert a DVD.■Select the AAVV11input source on the TV using the IINNPPUUTTbutton on the remote control. ■Refer to the DVD player's manual for operating instructions.21HDMI ConnectionConnect the HDMI output of the DVD to theHHDDMMII//DDVVII IINN11, 22, or 33* jack on the TV.No separate audio connection is necessary.HDMI supports both audio and video.1. How to connect2. How to use■Select the HHDDMMII11, HHDDMMII22, or HHDDMMII33* input source onthe TV using the IINNPPUUTTbutton on the remote control.■Refer to the DVD player's manual for operating instructions.21COMPONENT INAUDIO(RGB/DRGB(PC)12VIDEOLYPBPRAHDMI/DVI IN 21HDMI-DVD OUTPUT1* HDMI 3: Except 42/47/52LG50DC
EXTERNAL EQUIPMENT SETUP23VCR SETUPAntenna Connection■To avoid picture noise (interference), leave an adequate distance between the VCR and TV.■If the 4:3 picture format is used; the fixed images on the sides of the screen may remain visible on the screen.This phenomenon is common to all TVs and is not covered by warranty.ANTENNA/CABLE INE)COAXIALUDIO OUTL RS-VIDEO VIDEOOUTPUTSWITCHANT INANT OUTEO L R(MONO)AUDIOAUDIO OUTWall JackAntenna12Connect the RF antenna out socket of theVCR to the AANNTTEENNNNAA//CCAABBLLEE IINNsock-et on the TV.Connect the antenna cable to the RFantenna in socket of the VCR.1. How to connect2. How to use■Set VCR output switch to 3 or 4 and thentune TV to the same channel number.■Insert a video tape into the VCR and pressPLAY on the VCR. (Refer to the VCR owner’smanual.)21
EXTERNAL EQUIPMENT SETUP24EXTERNAL EQUIPMENT SETUPComposite (RCA) ConnectionGGIf you have a mono VCR, connect the audio cable fromthe VCR to the AAUUDDIIOO LL//MMOONNOOjack of the TV.NOTE!NT INAUDIO(RGB/DVI)REMOTECONTROL INANTENNA/CABLE INRS-232C IN(CONTROL & SERVICE)L RAUDIOOPTICAL COAXIALDIGITAL AUDIO OUTAV IN 1VIDEO L R(MONO)AUDIOS-VIDEOAUDIO OUTL RS-VIDEO VIDEOOUTPUTSWITCHANT INANT OUT1Connect the AAUUDDIIOO/VVIIDDEEOOjacks between TV andVCR. Match the jack colors (Video = yellow, Audio Left= white, and Audio Right = red)1. How to connect2. How to use■Insert a video tape into the VCR and press PLAY on the VCR.(Refer to the VCR owner’s manual.)■Select the AAVV11input source on the TV using the IINNPPUUTTbutton on the remote control.■If connected to AAVV IINN22, select AAVV22input source on the TV.1GGDo not connect to both Video and S-Video at the sametime. In the event that you connect both Video and theS-Video cables, only the S-Video will work.CAUTIONGGS-Video provides better qualitythan composite. Use it whenavailable.NOTE!S-Video ConnectionNT INAUDIO(RGB/DVI)REMOTECONTROL INANTENNA/CABLE INRS-232C IN(CONTROL & SERVICE)L RAUDIOOPTICAL COAXIALDIGITAL AUDIO OUTAV IN 1VIDEO LR(MONO)AUDIOS-VIDEOAUDIO OUTL RS-VIDEO VIDEOOUTPUTSWITCHANT INANT OUT12Connect the S-VIDEO output of the VCR to theSS--VVIIDDEEOO input on the TV.Connect the audio outputs of the VCR to the AAUUDDIIOOinput jacks on the TV.1. How to connect2. How to use■Insert a video tape into the VCR and press PLAY on the VCR.(Refer to the VCR owner’s manual.)■Select the AAVV11input source on the TV using the IINNPPUUTTbutton on the remote control.21
EXTERNAL EQUIPMENT SETUP25OTHER A/V SOURCE SETUPAV IN 2L/MONORAUDIOVIDEOHDMI IN 3 USB INL RVIDEOCamcorderVideo Game SetConnect the AAUUDDIIOO/VVIIDDEEOOjacksbetween TV and external equipment.Match the jack colors.(Video = yellow, Audio Left = white, andAudio Right = red)1. How to connect2. How to use■Select the AAVV22input source on the TV usingthe IINNPPUUTTbutton on the remote control.■If connected to AAVV IINN11input, select the AAVV11input source on the TV.■Operate the corresponding external equipment.11
EXTERNAL EQUIPMENT SETUP26PC SETUPEXTERNAL EQUIPMENT SETUPThis TV provides Plug and Play capability, meaning that the PC adjusts automatically to the TV's settings. VGA (D-Sub 15 pin) ConnectionCOMPONENT INREMOTCONTROL12(VIDEOLYPBPRRAUDIODVI IN RGB INAUDIO(RGB/DVI)RGB(PC)RGB OUTPUT AUDIO12Connect the VGA output of the PC to the RRGGBB((PPCC)) jack on the TV.Connect the PC audio output to the AAUUDDIIOO((RRGGBB//DDVVII))jack on the TV.1. How to connect2. How to use■Turn on the PC and the TV.■Select the RRGGBB--PPCCinput source on the TV using theIINNPPUUTTbutton on the remote control.21DVI to HDMI ConnectionConnect the DVI output of the PC to the HHDDMMII//DDVVIIIINN 11, 22, or 33* jack on the TV.Connect the PC audio output to the AAUUDDIIOO((RRGGBB//DDVVII)) jack on the TV.1. How to connect2. How to use■Turn on the PC and the TV.■Select the HHDDMMII11, HHDDMMII22, or HHDDMMII33* input source onthe TV using the IINNPPUUTTbutton on the remote control.21COMPONENT INRCO12VIDEOLYPBPRRAUDIOHDMI/DVI IN 21RGB INAUDIO(RGB/DVI)RGB(PC)DVI-PC OUTPUT AUDIO12* HDMI 3: Except 42/47/52LG50DC
EXTERNAL EQUIPMENT SETUP27Supported Display Specifications (RGB-PC, HDMI-PC)Resolution 720x400640x350640x4801920x1080HDMI-PCHorizontal Vertical Frequency(KHz)Frequency(Hz)31.468 70.0931.469 70.0831.469 59.9435.156 56.2537.879 60.3148.363 60.0056.476 70.0647.776 59.8763.981 60.0247.712 60.01575.00 60.0066.587 59.93467.5 60.00GGTo get the the best picture quality, adjust the PCgraphics card to 1920x1080.GGDepending on the graphics card, DOS mode maynot work if a HDMI to DVI Cable is in use.GGIn PC mode, there may be noise associated withthe resolution, vertical pattern, contrast or bright-ness. If noise is present, change the PC output toanother resolution, change the refresh rate toanother rate or adjust the brightness and contraston the PICTURE menu until the picture is clear.GGAvoid keeping a fixed image on the screen for along period of time. The fixed image couldbecome permanently imprinted on the screen.GGThe synchronization input form for Horizontal andVertical frequencies is separate.GGDepending on the graphics card, some resolutionsettings may not allow the image to be posi-tioned on the screen properly.GGIf there are overscan in HDMI-PC 1920x1080,change aspect ratio to JJuusstt ssccaann.NOTES!800x6001024x7681280x7681280x10241360x7681600x12001920x1080RGB-PC
EXTERNAL EQUIPMENT SETUP28EXTERNAL EQUIPMENT SETUPScreen Setup for PC modeSelecting ResolutionYou can choose the resolution in RGB-PC mode. The PPoossiittiioonn, PPhhaassee, and SSiizzeecan also be adjusted.Select PPIICCTTUURREE.Select SSccrreeeenn ((RRGGBB--PPCC)).Select RReessoolluuttiioonn.Select the desired resolution.1024 x 7681280 x 7681360 x 768Auto config.ResolutionGPositionSizePhaseResetSCREENMovePrev.MENU1MENU342ENTERENTERENTER5ENTEREnterMovePICTURERG• Backlight 80 • Contrast 90• Brightness 50• Sharpness 60• Color 60• Tint 0• Advanced Control• ResetScreen (RGB-PC)E
EXTERNAL EQUIPMENT SETUP29Auto ConfigureAutomatically adjusts picture position and minimizes image instability. After adjustment, if the image is stillnot correct, try using the manual settings or a different resolution or refresh rate on the PC.Select SSccrreeeenn ((RRGGBB--PPCC)).Select AAuuttoo ccoonnffiigg...Auto config. GResolutionPositionSizePhaseResetSCREENMovePrev.MENUTo Set32ENTERENTERSelect YYeess.4ENTERStart Auto Configuration.5ENTERSelect PPIICCTTUURREE.1MENU• If the position of the image is still notcorrect, try Auto adjustment again.• If picture needs to be adjusted againafter Auto adjustment in RGB-PC, youcan adjust the PPoossiittiioonn, SSiizzee orPPhhaassee.Yes NoEnterMovePICTURERG• Backlight 80 • Contrast 90• Brightness 50• Sharpness 60• Color 60• Tint 0• Advanced Control• ResetScreen (RGB-PC)E
EXTERNAL EQUIPMENT SETUP30EXTERNAL EQUIPMENT SETUPAdjustment for screen Position, Size, and PhaseIf the picture is not clear after auto adjustment and especially if characters are still trembling, adjust the picturephase manually.This feature operates only in RGB-PC mode.Select PPoossiittiioonn, SSiizzee, or PPhhaassee.Make appropriate adjustments.Auto config.ResolutionPositionGSizePhaseResetGFDESCREENMovePrev.MENU3ENTER4ENTER■PPoossiittiioonn: This function is to adjust pic-ture to left/right and up/down as youprefer. ■SSiizzee: This function is to minimize anyvertical bars or stripes visible on thescreen background. And the horizontalscreen size will also change.■PPhhaassee: This function allows you toremove any horizontal noise and clear orsharpen the image of characters.Select PPIICCTTUURREE.Select SSccrreeeenn ((RRGGBB--PPCC)).1MENU2ENTER5ENTEREnterMovePICTURERG• Backlight 80 • Contrast 90• Brightness 50• Sharpness 60• Color 60• Tint 0• Advanced Control• ResetScreen (RGB-PC)E
EXTERNAL EQUIPMENT SETUP31Screen Reset (Reset to original factory values)Returns PPoossiittiioonn, SSiizzee, and PPhhaasseeto the default factory settings.This feature operates only in RGB-PC mode.Auto config.PositionResolutionSizePhaseResetGSCREENMovePrev.MENUTo SetSelect RReesseett.3ENTERSelect PPIICCTTUURREE.Select SSccrreeeenn ((RRGGBB--PPCC)).1MENU2ENTERSelect YYeess.4ENTER5ENTERYes NoEnterMovePICTURERG• Backlight 80 • Contrast 90• Brightness 50• Sharpness 60• Color 60• Tint 0• Advanced Control• ResetScreen (RGB-PC)E
EXTERNAL EQUIPMENT SETUP32USB CONNECTIONEXTERNAL EQUIPMENT SETUPAV IN 2L/MONORAUDIOVIDEOHDMI IN 3 USB INConnect the USB device to the UUSSBB IINNjack on the sideof TV. 1. How to connect12. How to use■After connecting the UUSSBB IINNjack, you use the USB function.(GGpp..4488)1(Except 42/47/52LG50DC)
EXTERNAL EQUIPMENT SETUP33AUDIO OUT CONNECTIONSend the TV’s audio to external audio equipment via the Audio Output port.INGB/DVI)RS-232C IN(CONTROL & SERVICE)L RAUDIOL RAUDIOAUDIO OUTAV IN 1VIDEO L R(MONO)AUDIOS-VIDEO1IODVI)REMOTECONTROL INANTENNA/CABLE INRS-232C IN(CONTROL & SERVICE)RAUDIOOPTICAL COAXIALDIGITAL AUDIO OUTAV IN 1VIDEO L R(MONO)AUDIOS-VIDEOAUDIO OUT12GGWhen connecting with external audio equipments, such asamplifiers or speakers, you can turn the TV speakers off inthe menu. (GG pp..7733)NOTE!GDo not look into the optical output port. Looking at thelaser beam may damage your vision.GGBlock the SPDIF out (optical/coaxial) about the contentswith ACP(Audio Copy Protection) function.CAUTIONConnect one end of the optical or coaxial cable to theTV’s OOPPTTIICCAALL or CCOOAAXXIIAALLport of DDIIGGIITTAALL AAUUDDIIOOOOUUTT.Connect the other end of the optical or coaxial cable tothe digital audio input on the audio equipment.Set the “TV Speaker option - Off” in the AUDIO menu. (GGpp..7733). See the external audio equipment instruction man-ual for operation.1. How to connect231Connect audio outputs to the TV’s AAUUDDIIOO OOUUTTjacks.Set the “TV Speaker option - Off” in the AUDIO menu.(GGpp..7733). See the external audio equipment instructionmanual for operation.1. How to connect21AnalogDigital
USB48USBENTRY MODESWhen you connect a USB device, this screen is displayed automatically.In USB device, you can not add a new folder or delete the existing folder.Precautions when using the USB deviceGGOnly a USB storage device is recognizable. GGIf the USB storage device is connected through aUSB hub, the device is not recognizable.GGA USB storage device using an automatic recogni-tion program may not be recognized.GGA USB storage device which uses its own drivermay not be recognized.GGUSB multi-card reader or USB hard drive may notoperate smoothly or may not operate at all.GGThe recognition speed of a USB storage devicemay depend on each device.GGPlease do not turn off the TV or unplug the USBdevice when the connected USB storage device isworking. When such device is suddenly separatedor unplugged, the stored files or the USB storagedevice may be damaged. GGPlease do not connect the USB storage devicewhich was artificially maneuvered on the PC. Thedevice may cause the product to malfunction orfail to be played. Never forget to use only a USBstorage device which has normal music files orimage files.GGPlease use only a USB storage device which wasformatted as a FAT or NTFS file system providedwith the Windows operating system. In case of astorage device formatted as a different utility pro-gram which is not supported by Windows, it maynot be recognized.GGPlease connect power to a USB storage devicewhich requires an external power supply. If not,the device may not be recognized.GGPlease connect a USB storage device with cable isoffered by USB maker. If connected with cable isnot offered by USB maker or an excessively longcable, the device may not be recognized.GGSome USB storage devices may not be supportedor operated smoothly.GGBecause the TV doesn’t support file sorting forUSB storage device, the file on the storage devicewill be displayed in the order saved.GGPlease backup important files because data onUSB device may be damaged. Data management isconsumer's responsibility and as a result, the man-ufacturer does not cover data damage.When removing the USB deviceConnect the USB device to the UUSSBB IINNjacks on the side of TV. 3Select PPhhoottoo LLiisstt or MMuussiiccLLiisstt. 1USB INPhoto List Music ListSelect UUSSBB EEjjeecctt.Select the UUSSBB EEjjeeccttmenu before removing theUSB device.2ENTER1Q. MENU2ENTER■It doesn’t support USB HDD■This TV supports JPG and MP3.
USB50USBPhoto Selection and Popup MenuSelect the target folder or drive.Select the desired photos.2Show the Popup menu.31■Use the CCHH button to navigation in thephoto page.■Use the FFAAVVbutton to mark or unmark aphoto. When one or more photos are marked,you can view individual photos or a slide showof the marked photos. If no photos are marked,you can view all photos individually or all pho-tos in the folder in a slide show.4Select the desired Popup menu.ENTERENTERENTERWhen you select a file (not folder), this PopUpmenu is displayed.GGVViieeww: Display the selected item. GGMMaarrkk AAllll: Mark all photos on the screen.GGUUnnmmaarrkk AAllll: Deselect all marked photos.GGDDeelleettee: Delete the selected photo item.GGCClloossee: Close the pop-up menu.USB DevicePage 2/3No MarkedPhoto ListUpperFree Space 150MB1366x768, 125KBKY101 06/10/2008KY102 04/03/2008JMJ001 01/01/2000JMJ002 06/15/2008JMJ003 04/03/2008JMJ004 02/18/2008KY103 03/30/2008KY104 06/19/2008KY105 01/31/2008JMJ005 05/13/2008JMJ006 05/26/2008JMJ007 02/18/2008JMJ008 02/18/2008UpperUSB DevicePage 2/3No MarkedPhoto ListUpperFree Space 150MB1366x768, 125KBKY101 06/10/2008KY102 04/03/2008JMJ001 01/01/2000JMJ002 06/15/2008JMJ003 04/03/2008JMJ004 02/18/2008KY103 03/30/2008KY104 06/19/2008KY105 01/31/2008JMJ005 05/13/2008JMJ006 05/26/2008JMJ007 02/18/2008JMJ008 02/18/2008UpperDrive1Drive1JMJ001JMJ001Move Move Page Mark ExitCH FAV RETURNPopUp MenuMove Move Page Mark ExitCH FAV RETURNPopUp Menu1366x768125KBView Mark AllDeleteClose
USB52USBSelect the SSiiddee SShhooww, ((RRoottaattee)),DDeelleettee,OOppttiioonn, or HHiiddee..■Use button to select the previous ornext photo. ■Use button to select and controlthe menu on the full-sized screen.ENTER6NOTE!GGThis TV will not be able to decodemost JPG images saved using theProgressive option.1/17Slide Show Delete Option HidePress FF GGto set the time interval betweenslides.Slide Speed Fast CancelEnterGGSSlliiddee SShhooww: Selected photos are displayed during theslide show. If no photo is selected, all photos in the cur-rent folder are displayed during slide show.■Set the time interval of the slide show in OOppttiioonn.■A slide show continues for a maximum of 4 hours.After 4 hours, the slide show will end and go to TVmode or external input mode.GG((RRoottaattee)): Rotate photos.■Rotates the photo 90°, 18 0 °, 270°, 360°clockwise.GGDDeelleettee: Delete photos.GGOOppttiioonn: Set values for SSlliiddee SSppeeeedd. ■Use button and EENNTTEERRbutton to set values.Then go to and press EENNTTEERRto save the set-tings.GGHHiiddee : Hide the menu on the full-sized screen.■To see the menu again on the full-sized screen, pressEENNTTEERR button to display.GG
USB54USBMusic Selection and Popup Menu■Use the CCHH button to navigation inthe music page.■Use FFAAVVbutton to mark or unmark a musicfile. If no music is marked, all the music in thefolder will be played in sequence. When one ormore music files are marked, the marked musicfiles will be played in sequence. If you want tolisten to only one song repeatedly, just markthat one file and play.Up to 6 music titles are listed per page.Select the target folder or drive.Select the desired musics.Show the Popup menu.Select the desired Popup menu.2314ENTERENTERENTER5RETURNReturn to TV viewingUSB DevicePage 1/1No MarkedMusic ListUpperFree Space 150MB3945 KB, 128 KbpsDrive1ArirangMove Move Page Mark ExitCH FAV RETURNPopUp MenuPlay TimeTitleUpperGood ByeArirangUSB DevicePage 1/1No MarkedMusic ListUpperFree Space 150MB3945 KB, 128 KbpsDrive1ArirangMove Move Page Mark ExitCH FAV RETURNPopUp MenuPlay TimeTitleUpperGood ByeArirang05:3004:123945 KB128 KbpsPlay Mark AllDeleteCloseGGPPllaayy (During stop): Play the selected music.Once a song finishes playing, the next selectedone will be played. When there are no selectedmusics to play, the next one in the current fold-er will be played. If you go to a different folderand press the EENNTTEERRbutton, the currentmusic in playback will stop.GGSSttoopp PPllaayy (During playback): Stop the play-ing musics.GGMMaarrkk AAllll: Mark all musics in the folder.GGUUnnmmaarrkk AAllll: Deselect all marked music.GGDDeelleettee: Delete the selected music.GGCClloossee: Close the pop-up menu.
USB55■The play information box (as shown below) will automaticallymove across the screen when there is no user input to pre-vent a fixed image remaining on the screen for a extendedperiod of time.NOTE!GGWhen music is playing, is displayed in front of the music play time.GGA damaged or corrupted music file that does not play displays 00:00 as the play time.GGMusic files with copy-protection will not play.GGPress EENNTTEERR, AA, or RREETTUURRNN button to stop the screen saver.GGThis TV can not play music files less than 16 Kbytes.
APPENDIX98APPENDIXTROUBLESHOOTINGTThhee ooppeerraattiioonn ddooeess nnoott wwoorrkk nnoorrmmaallllyy..TThhee vviiddeeoo ffuunnccttiioonn ddooeess nnoott wwoorrkk..No picture &No soundNo or poor coloror poor picturePoor reception on some channelsLines or streaksin picturesNo picture when connecting HDMIHorizontal/vertical barsor picture shakingPicture appears slowly after switching onThe remote controldoesn’t workPower is suddenly turned off■Check to see if there is any object between the product and the remote controlcausing obstruction. Ensure you are pointing the remote control directly at the TV.■Ensure that the batteries are installed with correct polarity (+ to +, - to -).■Ensure that the correct remote operating mode is set: TV, VCR etc.■Install new batteries.■Is the sleep timer set?■Check the power control settings. Power interrupted.■Check whether the product is turned on.■Try another channel. The problem may be with the broadcast.■Is the power cord inserted into wall power outlet?■Check your antenna direction and/or location.■Test the wall power outlet, plug another product’s power cord into the outletwhere the product’s power cord was plugged in.■This is normal, the image is muted during the product startup process. Pleasecontact your service center, if the picture has not appeared after five minutes.■Adjust Color in menu option.■Keep a sufficient distance between the product and the VCR.■Try another channel. The problem may be with the broadcast.■Are the video cables installed properly?■Activate any function to restore the brightness of the picture. ■Check for local interference such as an electrical appliance or power tool.■Station or cable product experiencing problems, tune to another station.■Station signal is weak, reorient antenna to receive weaker station.■Check for sources of possible interference.■Check antenna (Change the direction of the antenna).■Check HDMI cable over version 1.3.The HDMI cables don’t support HDMI version 1.3, it cause flickers or no screendisplay. In this case use the latest cables that support HDMI version 1.3.
APPENDIX99TThheerree iiss aa pprroobblleemm iinn PPCC mmooddee.. ((OOnnllyy PPCC mmooddee aapppplliieedd))■Adjust resolution, horizontal frequency, or vertical frequency.■Check the input source.■Work the Auto configure or adjust clock, phase, or H/V position. (Option)■Check the signal cable.■Reinstall the PC video card.The signal is out of rangeScreen color is unstableor single colorVertical bar or stripe on background &Horizontal Noise &Incorrect positionPicture OK & No soundUnusual sound frominside the productNo sound when connectingHDMI/USBNo output from one of the speakersTThhee aauuddiioo ffuunnccttiioonn ddooeess nnoott wwoorrkk..■Press the VOL or VOLUME button.■Sound muted? Press MUTE button.■Try another channel. The problem may be with the broadcast.■Are the audio cables installed properly?■Adjust Balance in menu option.■A change in ambient humidity or temperature may result in an unusual noisewhen the product is turned on or off and does not indicate a fault with theproduct.■Check HDMI cable over version 1.3.■Check USB cable over version 2.0.■Use normal MP3 file.
APPENDIX100APPENDIXMAINTENANCEEarly malfunctions can be prevented. Careful and regular cleaning can extend the amount of time you canenjoy your new TV. Caution: Be sure to turn the power off and unplug the power cord before you begin any cleaning.Cleaning the ScreenHere’s a great way to keep the dust off your screen for a while. Wet a soft cloth in a mixture of lukewarmwater and a little fabric softener or dish washing detergent. Wring the cloth until it’s almost dry, and thenuse it to wipe the screen.Make sure the excess water is off the screen, and then let it air-dry before you turn on your TV.Cleaning the Cabinet■To remove dirt or dust, wipe the cabinet with a soft, dry, lint-free cloth.■Please be sure not to use a wet cloth.Extended AbsenceGG If you expect to leave your TV dormant for a long time (such as a vacation), it’s a good idea to unplugthe power cord to protect against possible damage from lightning or power surges.CAUTION21
APPENDIX101PRODUCT SPECIFICATIONS■The specifications shown above may be changed without prior notice for quality improvement.MODELSAC100-240V ~ 50/60HzNTSC-M, ATSC, 64 & 256 QAMVHF 2-13, UHF 14-69, CATV 1-135, DTV 2-69, CADTV 1-13575 ohm32 ~ 104°F (0 ~40°C)Less than 80%-4 ~ 140°F (-20 ~60°C)Less than 85%Dimensions(Width x Height x Depth)WeightPower requirementTelevision SystemProgram CoverageExternal Antenna ImpedanceEnvironment conditionWith standWithout standWith standWithout standOperating TemperatureOperating HumidityStorage TemperatureStorage Humidity37LH50(37LH50-UC)42LH50 (42LH50-UC)42LG50DC (42LG50DC-UG)42LG55 (42LG55-UE)36.8 x 26.9 x 11.5 inches936.4 x 685.4 x 293.4 mm36.8 x 24.1 x 3.4 inches936.4 x 612.8 x 88.0 mm40.3 pounds / 18.3 kg34.3 pounds / 15.6 kg40.7 x 28.9 x 11.5 inches1034.0 x 735.0 x 294.0 mm40.7 x 26.1 x 3.5 inches1034.0 x 663.0 x 91.0 mm54.0 pounds / 24.5 kg48.5 pounds / 22.0 kgMODELS 47LH50(47LH50-UC)47LG50DC (47LG50DC-UG)47LG55 (47LG55-UE)52LH50(52LH50-UC)52LG50DC (52LG50DC-UG)Dimensions(Width x Height x Depth)WeightWith standWithout standWith standWithout stand45.5 x 32.0 x 13.5 inches1156.2 x 813.1 x 342.9 mm45.5 x 29.1 x 4.0 inches1156.2 x 739.2 x 103.0 mm64.3 pounds / 29.2 kg54.2 pounds / 24.6 kg50.8 x 35.1 x 13.5 inches1291.7 x 892.2 x 342.9 mm50.8 x 32.1 x 4.5 inches1291.7 x 817.0 x 115.3 mm87.0 pounds / 39.5 kg76.9 pounds / 34.9 kg
APPENDIX102PROGRAMMING THE REMOTE CONTROLAPPENDIXThe provided universal remote control can be programmed to operate most remote-controllable devices.Note that the remote may not control all models of other brands.Programming a code into a remote modeTesting your remote control.To find out whether your remote control can operate other components without programming, turn on acomponent such as a STB and press the corresponding mode button (such as a SSTTBB) on the remote con-trol, while pointing at the component. Test the PPOOWWEERRand CCHHbuttons to see if the componentresponds correctly. If the component does not operate correctly, the remote control requires programmingto operate the device.Turn on the component to be programmed, then press the corresponding mode button (such as SSTTBB) onthe remote control. The remote control button of the desired device is illuminated.Press the MMEENNUUand MMUUTTEEbuttons simultaneously, and the remote control is ready to be programmed withthe code.Enter a code number using the number buttons on the remote control. Programming code numbers for thecorresponding component can be found on the following pages. If the code is correct, the device will turnoff.Press the MMEENNUUbutton to store the code.Test the remote control functions to see if the component responds correctly. If not, repeat from step 2.234561
APPENDIX103Remote Control CodeBrand Codes Brand Codes Brand CodesAIWA 034AKAI 016 043 046 124125 146AMPRO 072ANAM 031 033 103AUDIO DYNAMICS012 023 039 043BROKSONIC 035 037 129CANON 028 031 033CAPEHART 108CRAIG 003 040 135CURTIS MATHES 031 033 041DAEWOO 005 007 010 064065 108 110 111112 116 117 119DAYTRON 108DBX 012 023 039 043DYNATECH 034 053ELECTROHOME 059EMERSON 006 017 025 027029 031 034 035036 037 046 101129 131 138 153FISHER 003 008 009 010FUNAI 034GE 031 033 063 072107 109 144 147GO VIDEO 132 136HARMAN KARDON 012 045HITACHI 004 018 026 034043 063 137 150INSTANTREPLAY 031 033JCL 031 033JCPENNY 012 013 015 033040 066 101JENSEN 043JVC 012 031 033 043048 050 055 060130 150 152KENWOOD 014 034 039 043047 048LG (GOLDSTAR) 001 012 013 020101 10 6 114 123 LLOYD 034LXI 003 009 013 014017 034 101 106MAGIN 040MAGNAVOX 031 033 034 041067 068MARANTZ 012 031 033 067069MARTA 101MATSUI 027 030MEI 031 033MEMOREX 003 010 014 031033 034 053 072101 102 134 139MGA 045 046 059MINOLTA 013 020MITSUBISHI 013 020 045 046049 051 059 061151MTC 034 040MULTITECH 024 034NEC 012 023 039 043048NORDMENDE 043OPTONICA 053 054PANASONIC 066 070 074 083133 140 145PENTAX 013 020 031 033063PHILCO 031 034 067PHILIPS 031 033 034 054067 071 101PILOT 101PIONEER 013 021 048PORTLAND 108PULSAR 072QUARTZ 011 014QUASAR 033 066 075 145RCA 013 020 033 034040 041 062 063107 109 140 144145 147REALISTIC 003 008 010 014031 033 034 040053 054 101RICO 058RUNCO 148SALORA 014SAMSUNG 032 040 102 104105 107 109 112113 115 120 122125SANSUI 022 043 048 135SANYO 003 007 010 014102 134SCOTT 017 037 112 129131SEARS 003 008 009 010013 014 017 020031 042 073 081101SHARP 031 054 149SHINTOM 024SONY 003 009 031 052056 057 058 076077 078 149SOUNDESIGN 034STS 013SYLVANIA 031 033 034 059067SYMPHONIC 034TANDY 010 034TATUNG 039 043TEAC 034 039 043TECHNICS 031 033 070TEKNIKA 019 031 033 034101THOMAS 034TMK 006TOSHIBA 008 013 042 047059 082 112 131TOTEVISION 040 101UNITECH 040VECTOR RESEARCH012VICTOR 048VIDEO CONCEPTS012 034 046VIDEOSONIC 040WARDS 003 013 017 024031 033 034 040053 054 131YAMAHA 012 034 039 043ZENITH 034 048 056058 072 080 101VCR
APPENDIX104APPENDIXBrand Codes Brand Codes Brand CodesALPHASTAR DSR 123AMPLICA 050BIRDVIEW 051 126 129CHANNEL MASTER013 014 015 018036 055CHAPARRAL 008 009 012 077CITOH 054CURTIS MATHES 050 145DRAKE 005 006 007 010 011 052 112 116141DX ANTENNA 024 046 056 076ECHOSTAR 038 040 057 058093 094 095 096097 098 099 100122ELECTRO HOME 089EUROPLUS 114FUJITSU 017 021 022 027133 134GENERAL INSTRUMENT003 004 016 029031 059 101HITACHI 139 140HOUSTON TRACKER033 037 039 051057 104HUGHES 068JANIEL 060 147JERROLD 061KATHREIN 108LEGEND 057LG 001LUTRON 132LUXOR 062 144MACOM 010 059 063 064065MEMOREX 057NEXTWAVE 028 124 125NORSAT 069 070PACE SKY SATELLITE143PANASONIC 060 142PANSAT 121PERSONAL CABLE 117PHILIPS 071PICO 105PRESIDENT 019 102PRIMESTAR 030 110 111PROSAT 072RCA 066 106REALISTIC 043 074SAMSUNG 123SATELLITE SERVICE CO028 035 047 057085SCIENTIFIC ATLANTA032 138SONY 103STARCAST 041SUPER GUIDE 020 124 125TEECOM 023 026 075 087088 090 107 130137TOSHIBA 002 127UNIDEN 016 025 042 043044 045 048 049078 079 080 086101 135 136VIEWSTAR 115WINEGARD 128 146ZENITH 081 082 083 084 091 120HDSTBDVDBrand Codes Brand Codes Brand CodesAPEX DIGITAL 022DENON 020 014GE 005 006HARMAN KARDON 027JVC 012LG 001 010 016 025MAGNAVOX 013MARANTZ 024MITSUBISHI 002NAD 023ONKYO 008 017PANASONIC 003 009PHILIPS 013PIONEER 004 026PROCEED 021PROSCAN 005 006RCA 005 006SAMSUNG 011 015SONY 007THOMPSON 005 006TOSHIBA 019 008YAMAHA 009 018ZENITH 010 016 025
APPENDIX105IR CODES■Configuration of frame 1st frameRepeat frame■Lead code■Repeat code■BBiitt ddeessccrriippttiioonn■FFrraammee iinntteerrvvaall:: TTff The waveform is transmitted as long as a key is depressed.C0 C1 C2 C3 C4 C5 C6 C7 C0 C1 C2 C3 C4 C5 C6 C7 D0 D1 D2 D3 D4 D5 D6 D7 D0 D1 D2 D3 D4 D5 D6 D7 Lead code Low custom code High custom code Data code Data code Repeat code Tf4.5 ms9 ms 2.25 ms 9 ms 0.55 ms 0.56 ms1.12 ms0.56 ms2.24 msTf TfTf=108ms @455KHzBit ”0” Bit ”1”1. How to Connect■Connect your wired remote control to the Remote Control port on the TV. 2. Remote Control IR Codes■Output waveform Single pulse, modulated with 37.917KHz signal at 455KHz T1TcCarrier frequencyFCAR = 1/TC = fOSC/12Duty ratio = T1/TC = 1/3
APPENDIX106APPENDIXCode Function Note(Hexa) Code Function Note(Hexa)08 POWERRemote control Button (Power On/Off)45 Q.MENU Remote control Button43 MENU Remote control Button0B INPUT Remote control Button10-19 Number Key 0-9 Remote control Button4C - (Dash) Remote control Button1A FLASHBK Remote control Button09 MUTE Remote control Button02 VOL + Remote control Button03 VOL - Remote control Button00 CH Remote control Button01 CH Remote control Button1E FAV Remote control Button40 Remote control Button41 Remote control Button07 Remote control Button06 Remote control Button44 ENTER Remote control Button5B RETURN Remote control Button7E SIMPLINK Remote control Button30 AV MODE Remote control ButtonB0 PLAY Remote control ButtonBA PAUSE Remote control ButtonB1 STOP Remote control ButtonBD REC Remote control Button8F REW Remote control Button8E FF Remote control ButtonExcept 42/47/52LG50DCD6 TV Discrete IR Code (TV Input Selection)C4 POWER ON Discrete IR Code (Only Power On)C5 POWER OFF Discrete IR Code (Only Power Off)5A AV1 Discrete IR Code (AV1 Input Selection)D0 AV2 Discrete IR Code (AV2 Input Selection)BF COMPONENT1 Discrete IR Code (Component1 Input Selection)D4 COMPONENT2 Discrete IR Code (Component2 Input Selection)D5 RGB-PC Discrete IR Code (RGB-PC Input Selection)CE HDMI1 Discrete IR Code (HDMI1 Input Selection)CC HDMI2 Discrete IR Code (HDMI2 Input Selection)E9 HDMI3 Discrete IR Code (HDMI3 Input Selection)76 Ratio 4:3 Discrete IR Code (Only 4:3 Mode)77 Ratio 16:9 Discrete IR Code (Only 16:9 Mode)AF Ratio Zoom Discrete IR Code (Only Zoom1 Mode)
APPENDIX107EXTERNAL CONTROL THROUGH RS-232CRS-232C SetupThe RS-232C port allows you connect the RS-232C input jack to an external control device (such as a computeror an A/V control system) to control the TV’s functions externally.■Note: RS-232C on this unit is intended to be used with third party RS-232C control hardware and software.The instructions below are provided to help with programming software or to test functionality using telenetsoftware.OVI)REMOTECONTROL INRAUDIOOPTICAL COAXIALDIGITAL AUDIO OUTAV IN 1VIDEO L R(MONO)AUDIOS-VIDEOAUDIO OUTRS-232C IN(CONTROL & SERVICE)Type of Connector; D-Sub 9-Pin MaleNo. Pin Name1 No connection2 RXD (Receive data)3 TXD (Transmit data)4 DTR (DTE side ready)5 GND6 DSR (DCE side ready)7 RTS (Ready to send)8 CTS (Clear to send)9 No Connection1659PCCommunication Parameters■Baud rate : 9600 bps (UART)■Data length : 8 bits■Parity : None■Stop bit : 1 bit■Communication code : ASCII code■Use a crossed (reverse) cable.NOTE!GGThis product has command echo back in theRS-232C Command.
APPENDIX108RS-232C ConfigurationsAPPENDIXUse this function to specify a TV ID number. Refer to ‘Real Data Mapping1’. GGpp..111111.Either cable below can be used.Set IDPC TVRXD 2 3 TXDTXD 3 2 RXDGND 5 5 GNDDTR 4 6 DSRDSR 6 4 DTRRTS 7 8 CTSCTS 8 7 RTSD-Sub 9 D-Sub 9PC TVRXD 2 3 TXDTXD 3 2 RXDGND 5 5 GNDDTR 4 6 DTRDSR 6 4 DSRRTS 7 7 RTSCTS 8 8 CTSD-Sub 9 D-Sub 97-Wire Configuration(Serial female-female NULL modem cable)3-Wire Configurations(Not standard)Select OOPPTTIIOONN.Select SSeett IIDD.Choose the desired TV ID number. The adjustment range of Set ID is 1~99.1MENU32ENTERENTER4RETURNReturn to the previous menu.MENUReturn to TV viewing.EnterMoveOPTIONLanguage : EnglishInput LabelSIMPLINK : OnKey Lock : OffCaption : OffSet ID : 1Power IndicatorInitial Setting : HomeEnterMoveOPTIONLanguage : EnglishInput LabelSIMPLINK : OnKey Lock : OffCaption : OffSet ID : 1Power IndicatorInitial Setting : HomeFF 1GGClose
APPENDIX109Command Reference ListCCOOMMMMAANNDD11CCOOMMMMAANNDD2219. Channel TuningDATA(Hexadecimal)CCOOMMMMAANNDD11CCOOMMMMAANNDD22DATA(Hexadecimal)CCOOMMMMAANNDD11CCOOMMMMAANNDD22DATA00(Hexadecimal)DATA01(Hexadecimal)DATA02(Hexadecimal)DATA03(Hexadecimal)DATA04(Hexadecimal)DATA05(Hexadecimal)physical major major low minor high minor low attributeprogram high program lowma01. Power k a 00 ~0102. Input Select x b (GGp.110)03. Aspect Ratio k c (GGp.110)04. Screen Mute k d 00 ~0105. Volume Mute k e 00 ~0106. Volume Control k f 00 ~6407. Contrast k g 00 ~6408. Brightness k h 00 ~6409. Color k i 00 ~6410. Tint k j 00 ~6411. Sharpness k k 00 ~6412. OSD Select k l 00 ~0113. Remote ControlLock ModeTransmission / Receiving ProtocolTTrraannssmmiissssiioonn[Command 1] : First command to control the set.(j, k, m or x)[Command 2] : Second command to control the set.[Set ID] : You can adjust the set ID to choose desired TV IDnumber in Setup menu. Adjustment range is 1~99.When selecting Set ID ‘0’, every connected the TV iscontrolled. Set ID is indicated as decimal (1~ 99)onmenu and as Hexa decimal (0x0~ 0x63)on transmission/receiving protocol.[DATA] : To transmit the command data.Transmit the ‘FF’ data to read status of command.[Cr] : Carriage ReturnASCII code ‘0x0D’[ ] : ASCII code ‘space (0x20)’* In this model, TV will not send the status during the standby mode.OOKK AAcckknnoowwlleeddggeemmeennttThe TV transmits ACK (acknowledgement) based on this for-mat when receiving normal data. At this time, if the data isdata read mode, it indicates present status data. If the data isdata write mode, it returns the data of the PC computer.* In this model, TV will not send the status during the standby mode.* Data Format[Command 2] : Use as command.[Set ID] : Use the small character, if set ID is 10, it will send the ‘0’, ‘a’.[DATA] : Use the small character, if data is 0 x ab, it will send the ‘a’, ‘b’.[OK] : Use the large character.EErrrroorr AAcckknnoowwlleeddggeemmeennttThe TV transmits ACK (acknowledgement) based on this for-mat when receiving abnormal data from non-viable functionsor communication errors.Data1: Illegal CodeData2: Not supported functionData3: Wait more time* In this model, TV will not send the status during the standby mode.* Data Format[Command 2] : Use as command.[Set ID] : Use the small character, if set ID is 10, it will send the ‘0’, ‘a’.[DATA] : Use the small character, if data is 0 x ab, it will send the ‘a’, ‘b’.[NG] : Use the large character[[CCoommmmaanndd11]][[CCoommmmaanndd22]][[ ]][[SSeett IIDD]][[ ]][[DDaattaa]][[CCrr]][[CCoommmmaanndd22]][[ ]][[SSeett IIDD]][[ ]][[OOKK]][[DDaattaa]][[xx]][[CCoommmmaanndd22]][[ ]][[SSeett IIDD]][[ ]][[NNGG]][[DDaattaa]][[xx]]14. Treble k r 00 ~6415. Bass k s 00 ~6416. Balance k t 00 ~6417.Color Temperaturek u 00 ~0218. Auto Configuration j u (GGp.112)20. Channel Add/Del m b 00 ~0121 . Key m c ( GGp.113)22. Backlight m g 00 ~6400 ~01k m
APPENDIX110APPENDIX0011..PPoowweerr ((CCoommmmaanndd:: kk aa))To control Power On/Off of the TV.Transmission [k][a][ ][Set ID][ ][Data][Cr]Data 00: Power Off Data 01: Power OnAcknowledgement [a][ ][Set ID][ ][OK/NG][Data][x]* In a like manner, if other functions transmit ‘FF’ databased on this format, Acknowledgement data feedbackpresents status about each function.* Note: In this model, TV will send the Acknowledgeafter power on processing completion.There might be a time delay between command andacknowledge.0022.. IInnppuutt SSeelleecctt ((CCoommmmaanndd:: xx bb))To select input source for TV. Transmission [x][b][ ][Set ID][ ][Data][Cr]Data 00: DTV (Antenna) Data 01: DTV (Cable)Data 10: Analog (Antenna) Data 11: Analog (Cable)Data 20: AV1 Data 21: AV2Data 40: Component 1 Data 41: Component 2Data 60: RGB-PC Data 90: HDMI1Data 91: HDMI2Data 92: HDMI3 (Except 42/47/52LG50DC)Acknowledgement [b][ ][Set ID][ ][OK/NG][Data][x]0033.. AAssppeecctt RRaattiioo ((CCoommmmaanndd:: kk cc))To adjust the screen format.Transmission [k][c][ ][Set ID][ ][Data][Cr]Data 01: 4:3 05: Zoom 202: 16:9 06: Set by program04: Zoom 1 09: Just scanReservedAcknowledgement [c][ ][Set ID][ ][OK/NG][Data][x]0044..SSccrreeeenn MMuuttee ((CCoommmmaanndd:: kk dd))To select screen mute on/off.Transmission [k][d][ ][Set ID][ ][Data][Cr]Data 00: Screen mute off (Picture on)Data 01: Screen mute on (Picture off)Acknowledgement [d][ ][Set ID][ ][OK/NG][Data][x]0055.. VVoolluummee MMuuttee ((CCoommmmaanndd:: kk ee))To control volume mute on/off.You can also adjust mute using the MUTE button onremote control.Transmission [k][e][ ][Set ID][ ][Data][Cr]Data 00: Volume mute on (Volume off)Data 01: Volume mute off (Volume on)Acknowledgement [e][ ][Set ID][ ][OK/NG][Data][x]0066.. VVoolluummee CCoonnttrrooll ((CCoommmmaanndd:: kk ff))To adjust volume.You can also adjust volume with the volume buttons onremote control.Transmission [k][f][ ][Set ID][ ][Data][Cr]Data Min: 00 ~Max: 64 (*transmit by Hexadecimal code)*Refer to ‘Real data mapping’. See page 111.Acknowledgement [f][ ][Set ID][ ][OK/NG][Data][x]0077.. CCoonnttrraasstt ((CCoommmmaanndd:: kk gg))To adjust screen contrast. You can also adjust contrast in the PICTURE menu.Transmission [k][g][ ][Set ID][ ][Data][Cr]Data Min: 00 ~Max: 64 (*transmit by Hexadecimal code)*Refer to ‘Real data mapping’. See page 111.Acknowledgement [g][ ][Set ID][ ][OK/NG][Data][x]0088.. BBrriigghhttnneessss ((CCoommmmaanndd:: kk hh))To adjust screen brightness.You can also adjust brightness in the PICTURE menu.Transmission [k][h][ ][Set ID][ ][Data][Cr]Data Min: 00 ~Max: 64 (*transmit by Hexadecimal code)*Refer to ‘Real data mapping’. See page 111.Acknowledgement [h][ ][Set ID][ ][OK/NG][Data][x]
APPENDIX1110099.. CCoolloorr ((CCoommmmaanndd:: kk ii))To adjust screen color.You can also adjust color in the PICTURE menu.Transmission [k][i][ ][Set ID][ ][Data][Cr]Data Min: 00 ~Max: 64 (*transmit by Hexadecimal code)*Refer to ‘Real data mapping’ as shown below.Acknowledgement [i][ ][Set ID][ ][OK/NG][Data][x]1100.. TTiinntt ((CCoommmmaanndd:: kk jj))To adjust screen tint.You can also adjust tint in the PICTURE menu.Transmission [k][j][ ][Set ID][ ][Data][Cr]Data Red: 00 ~Green: 64 (*transmit by Hexadecimal code)*Refer to ‘Real data mapping’ as shown below.Acknowledgement [ j ][ ][Set ID][ ][OK/NG][Data][x]1111.. SShhaarrppnneessss ((CCoommmmaanndd:: kk kk))To adjust screen sharpness.You can also adjust sharpness in the PICTURE menu.Transmission [k][k][ ][Set ID][ ][Data][Cr]Data Min: 00 ~Max: 64 (*transmit by Hexadecimal code)*Refer to ‘Real data mapping’ as shown below.Acknowledgement [k][ ][Set ID][ ][OK/NG][Data][x]1122.. OOSSDD SSeelleecctt ((CCoommmmaanndd:: kk ll))To select OSD (On Screen Display) on/off.Transmission [k][l][ ][Set ID][ ][Data][Cr]Data 00: OSD off Data 01: OSD onAcknowledgement [l][ ][Set ID][ ][OK/NG][Data][x]1133.. RReemmoottee CCoonnttrrooll LLoocckk MMooddee ((CCoommmmaanndd:: kk mm))To lock the remote control and the front panel controlson the set.Transmission [k][m][ ][Set ID][ ][Data][Cr]Data 00: Lock off Data 01: Lock onAcknowledgement [m][ ][Set ID][ ][OK/NG][Data][x]If you’re not using the remote control and front panelcontrols on the TV, use this mode. When main power ison/off, remote control lock is released.1144.. TTrreebbllee ((CCoommmmaanndd:: kk rr))To adjust treble. You can also adjust treble in the AUDIO menu.Transmission [k][r][ ][Set ID][ ][Data][Cr]Data Min: 00 ~Max: 64 (*transmit by Hexadecimal code)*Refer to ‘Real data mapping’ as shown.Acknowledgement [r][ ][Set ID][ ][OK/NG][Data][x]1155..BBaassss ((CCoommmmaanndd:: kk ss))To adjust bass.You can also adjust bass in the AUDIO menu.Transmission [k][s][ ][Set ID][ ][Data][Cr]Data Min: 00 ~Max: 64 (*transmit by Hexadecimal code)*Refer to ‘Real data mapping’ as shown below.Acknowledgement [s][ ][Set ID][ ][OK/NG][Data][x]1166.. BBaallaannccee ((CCoommmmaanndd:: kk tt))To adjust balance.You can also adjust balance in the AUDIO menu.Transmission [k][t][ ][Set ID][ ][Data][Cr]Data Min: 00 ~Max: 64 (*transmit by Hexadecimal code)*Refer to ‘Real data mapping’ as shown below.Acknowledgement [t][ ][Set ID][ ][OK/NG][Data][x]1177.. CCoolloorr TTeemmppeerraattuurree ((CCoommmmaanndd:: kk uu))To adjust color temperature.You can also adjust color temperature in the PICTURE menu.Transmission [k][u][ ][Set ID][ ][Data][Cr]Data 00: Medium 01: Cool 02: Warm Acknowledgement [u][ ][Set ID][ ][OK/NG][Data][x]*Real data mapping 0 : Step 0A : Step 10 (SET ID 10)F : Step 15 (SET ID 15)10 : Step 16 (SET ID 16)63 : Step 99 (SET ID 99)64 : Step 100
APPENDIX112APPENDIX1188.. AAuuttoo CCoonnffiigguurraattiioonn ((CCoommmmaanndd:: jj uu))To adjust picture position and minimize image shakingautomatically. Auto configuration only works in RGB-PCmode.Transmission [ j ][u][ ][Set ID][ ][Data][Cr]Data 1: To setAcknowledgement [u][ ][Set ID][ ][OK/NG][Data][x]1199.. CChhaannnneell TTuunniinngg ((CCoommmmaanndd:: mm aa))To tune channel to following physical/major/minor number.Transmission [m][a][ ][Set ID][ ][Data00][ ][Data01] [ ][Data02][ ][Data03][ ][Data04][ ][Data05][Cr]Digital channels have a Physical, Major, and Minor channelnumber. The Physical number is the actual digital channelnumber, the Major is the number that the channel shouldbe mapped to, and the Minor is the sub-channel. Sincethe ATSC tuner automatically maps the channel to theMajor number, the Physical number is not required whensending a command.Data 00: Physical Channel NumberNTSC air: 02~45, NTSC cable: 01, 0E~7DATSC air: 01~45, ATSC cable: 01~87Data 01 & 02: Major Channel Number Data 01: High byte Data 02: Low byteTwo bytes are available for the Major and Minor, nor-mally only the second byte is used. Data 03 & 04: Minor Channel Number Not needed for NTSC.
APPENDIX113Data05:The table above lists the binary code which must beconverted to Hexadecimal before sending. For example:The binary code to tune the sub source to an NTSCcable channel is “1000 0001”, which translates to “81”in Hex.* 7th bit : For which source do you want to change thechannel.* 6th bit: Use a two part or one part channel. Most casesjust use 0 since it’s ignored when using NTSC.* 5th bit: Use 0 with NTSC since it can only use the phys-ical channel number. Normally use 1 for ATSC since mosttimes it doesn’t matter what the physical number is.* 4th bit: Set to 0.* 3-0 bits: Choose signal type.* Tune Command Examples:1. Tune to the analog (NTSC) cable channel 35.Data 00 = Physical of 35 = 23Data 01 & 02 = No Major = 00 00Data 03 & 04 = No Minor = 00 00Data 05 = 0000 0001 in binary = 01Total = ma 00 23 00 00 00 00 012. Tune to the digital (ATSC) local channel 30-3.Data 00 = Don’t know Physical = 00Data 01 & 02 = Major is 30 = 00 1EData 03 & 04 = Minor is 3 = 00 03Data 05 = 0010 0010 in binary = 22Total = ma 00 00 00 1E 00 03 22Acknowledgement[a][ ][Set ID][ ][OK][Data00][Data01][Data02][Data03][Data04][x][a][ ][Set ID][ ][NG][Data00][x]2200.. CChhaannnneell AAdddd//DDeell ((CCoommmmaanndd:: mm bb))To add and delete the channelsTransmission [m][b][ ][Set ID][ ][Data][Cr]Data 00: Channel Delete Data 01: Channel AddAcknowledgement [b][ ][Set ID][ ][OK/NG][Data][x]2211.. KKeeyy ((CCoommmmaanndd:: mm cc))To send IR remote key code.Transmission [m][c][ ][Set ID][ ][Data][Cr]Data Key code: Refer to page 106.Acknowledgement [c][ ][Set ID][ ][OK/NG][Data][x]2222.. BBaacckklliigghhtt ((CCoommmmaanndd:: mm gg))To adjust screen backlight. Transmission [m][g][ ][Set ID][ ][Data][Cr]Data Min:00 ~ Max:64 (*transmit by Hexadecimal code)*Refer to ‘Real data mapping ’. See page 111.Acknowledgement [g][ ][Set ID][ ][OK/NG][Data][x]StepNTSC AirNTSC CableATSC AirATSC Cable_std ATSC Cable_hrcATSC Cable_ircATSC cable_autoReserved...Reserved100110011x1200001111x1300000000x14xxxxxxxxxxReserved501UseNo UseUsing PhysicalChannel601TwoOneTwo/One Part Channel701MainSubMain/Sub Picture 001010101x1
Regulatory Information cont. FCC Compliance StatementThis equipment has been tested and found to complywithin the limits of a Class B digital device pursuant to Part15 of the FCC Rules. These limits are designed to providereasonable protection against harmful interference in aresidential installation.This equipment generates, uses, and can radiate radiofrequency energy and if not installed and used inaccordance with the instructions, may cause harmfulinterference to radio communications. However, there isno guarantee that interference will not occur in a particularinstallation.If this equipment does cause harmful interference to radioor television reception (which can be determined byturning the equipment on and off), the user is encouragedto try to correct the interference by using one or more ofthe following measures:Reorient or relocate the receiving antenna.Increase the separation between the equipment and the receiver.Connect the equipment into an outlet on a circuitdifferent from that to which the receiver is connected.Consult the dealer or an experienced radio/TVtechnician for help.Caution: Changes or modifications not expressly approvedby the party responsible for compliance could void theuser's (or your) authority to operate the equipment. Onlyperipherals (digital input/output devices, terminals, printers,etc.) certified to comply with the Class B limits may beattached to this monitor. Operation with non-certifiedperipherals is likely to result in interference to radio and TV reception. Only shielded signal cables may be used withthis System.Canadian DOC NoticeThis Class B digital apparatus meets all requirements ofthe Canadian Interference-Causing Equipment Regulations. Cet appareil numérique de la classe Brespecte toutes les exigences du Règlement sur lematériel brouilleur du Canada.CE Conformity Notice (for Europe)Products with the “CE” Marking comply with the EMCDirective(89/336/EEC) and LOW VOLTAGE Directive(73/23/EEC) issued by the Commission of the EuropeanCommunity.Compiance with these directives implies conformity to thefollowing European Norms :• EN 55022 ; Radio Frequency Interference• EN 55024 ; Electromagnetic Immunity• EN 61000-3-2 ; Power Line Harmonics• EN 61000-3-3 ; Voltage Fluctuations• EN 60950-1 ; Product SafetyLow Radiation Compliance (MPR II)This monitor meets one of the strictest guidelines availabletoday for low radiation emissions, offering the user extrashielding and an antistatic screen coating. Theseguidelines, set forth by a government agency in Sweden,limit the amount of emission allowed in the Extremely LowFrequency (ELF) and Very Low Frequency (VLF)electromagnetic range.01NOTICEThe regulations are applied only to the products with theID LABEL indicating specific requirements.NOTICEThe regulations are applied only to the products with theID LABEL indicating specific requirements.NOTICEThe regulations are applied only to the products with theID LABEL indicating specific requirements.TCO'99 (TCO'99 applied model only)Congratulations!You have just purchased a TCO’99 approved and labelledproduct! Your choice has provided you with a productdeveloped for professional use. Your purchase has alsocontributed to reducing the burden on the environment andalso to the further development of environmentallyadapted electronics products.
Regulatory Information cont. 02Why do we have environmentally labelled computers?In many countries, environmental labelling has become anestablished method for encouraging the adaptation ofgoods and services to the environment. With the growingmanufacture and usage of electronic equipmentthroughout the world, there is a recognized concern for thematerials and substances used by electronic productswith regards to their eventual recycling and disposal. Byproper selection of these materials and substances, theimpact on the environment can be minimized.There are also other characteristics of a computer, such asenergy consumption levels, that are important from theviewpoints of both the work (internal) and natural (external)environments. Electronic equipment in offices is often leftrunning continuously, resulting in unnecessaryconsumption of large amounts of energy and additionalpower generation. From the standpoint of carbon dioxideemissions alone, it is vital to save energy.What does labelling involve?The product meets the requirements for the TCO’99scheme which provides for international and environmentallabelling of personal computers and/or displays. The labelling scheme was developed as a joint effort by the TCO (The Swedish Confederation of ProfessionalEmployees), Svenska Naturskyddsforeningen (The Swedish Society for Nature Conservation) andStatens Energimyndighet (The Swedish NationalEnergy Administration).Approval requirements cover a wide range of issues:ecology, ergonomics, emission of electrical and magneticalfields, energy consumption and electrical safety. Ecological criteria impose restrictions on the presence anduse of heavy metals, brominated and chlorinated flameretardants, and other substances. The product must beprepared for recycling and the manufacturing site(s) shallbe certified according to ISO14001 or EMAS registered.Energy requirements include a demand that the systemunit and/or display, after a certain period of inactivity,shall reduce its power consumption to a lower level in oneor more stages. The length of time to reactivate the systemunit shall be reasonable for the user.Labelled products must meet strict environmentaldemands, for example, in respect of the reduction ofelectrical and magnetical fields as well as work load andvisual ergonomics.Below you will find a brief summary of the ecologicalrequirements met by this product. The completeecological criteria document can be found at TCODevelopment’s website http://www.tcodevelopment.comor may be ordered from:TCO DevelopmentSE-114 94 STOCKHOLM, SwedenFax: +46 8 782 92 07Email : development@tco.seInformation regarding TCO’99 approved and labelledproducts may also be obtained athttp://www.tcodevelopment.comEcological requirementsFlame retardantsFlame retardants may be present in printed wiring boardlaminates, cables, and housings. Their purpose is toprevent, or at least to delay the spread of fire. Up to 30%by weight of the plastic in a computer casing can consist offlame retardant substances. Many flame retardantscontain bromine or chlorine, and these flame retardantsare chemically related to PCBs (polychlorinatedbiphenyls). Both the flame retardants containing bromineor chlorine and the PCBs are suspected of giving rise tohealth effects, including reproductive damage in fish-eating birds and mammals, due to the bio-accumulative*processes when not disposed of in accordance with strictstandards for disposal.TCO’99 requires that plastic components weighing morethan 25 grams shall not contain flame retardants withorganically bound bromine or chlorine. Flame retardantsare allowed in the printed wiring board laminates due tothe lack of commercially available alternatives.Cadmium**Cadmium is present in rechargeable batteries and in thecolour-generating layers of certain computer displays.TCO’99 requires that batteries, the colour-generatinglayers of display screens, and the electrical or electronicscomponents shall not contain any cadmium.Mercury**Mercury is sometimes found in batteries, relays andswitches. TCO’99 requires that batteries shall not containany mercury. It also demands that mercury is not presentin any of the electrical or electronics componentsassociated with the labelled unit. There is however one
Regulatory Information cont. 03exception. Mercury is, for the time being, permitted in theback light system of flat panel monitors as there today isno commercially available alternative. TCO aims onremoving this exception when a mercury free alternative isavailable.Lead**Lead can be found in picture tubes, display screens,solders and capacitors. TCO’99 permits the use of leaddue to the lack of commercially available alternatives, butin future requirements TCO Development aims atrestricting the use of lead._____________________________________________* Bio-accumulative is defined as substances which accumulate in living organisms.**Lead, Cadmium and Mercury are heavy metals which are bio-accumulative.TCO’03(TCO’03 applied model only)Congratulations!The display you have just purchased carries the TCO’03Displays label. This means that your display is designed,manufacturedand tested according to some of the strictest quality andenvironmental requirements in the world. This makes for ahigh performance product, designed with the user in focusthat also minimizes the impact on our natural environment.Some of the features of the TCO’03 Display requirements:Ergonomics• Good visual ergonomics and image quality in order toimprove the working environment for the user and toreduce sight and strain problems. Importantparameters are luminance, contrast, resolution,reflectance, colour rendition and image stability.Energy• Energy-saving mode after a certain time – beneficialboth for the user and the environment• Electrical safetyEmissions• Electromagnetic fields• Noise emissionsEcology• The product must be prepared for recycling and themanufacturer must have a certified environmentalmanagement system such as EMAS or ISO 14 001• Restrictions onchlorinated and brominated flame retardants andpolymersheavy metals such as cadmium, mercury and lead.The requirements included in this label have beendeveloped by TCO Development in co-operation withscientists, experts, users as well as manufacturers all overthe world. Since the end of the 1980s TCO has beeninvolved in influencing the development of IT equipment ina more user-friendly direction. Our labelling system startedwith displays in 1992 and is now requested by users andIT-manufacturers all over the world.For more information, please visitwww.tcodevelopment.comInformation for Environmental PreservationLGE. announced the 'LG Declaration for a CleanerEnvironment' in 1994, and this ideal has served as aguiding managerial principle ever since. The Declaration isa foundation that has allowed us to undertakeenvironmentally friendly activities in careful considerationof economic, environmental, and social aspects.We promote activities for environmental preservation, andwe specifically develop our products to embrace theconcept of environment-friendly. We minimize the hazardous materials contained in ourproducts. For example, there is no cadmium to be found inour monitors.Information for recyclingThis monitor may contain parts which could be hazardousto the environment. It is important that this monitor berecycled after use.LGE. handles all waste monitors through anenvironmentally acceptable recycling method. There areseveral take-back and recycling systems currently inEnglish
Regulatory Information cont. 04operation worldwide. Many parts will be reused andrecycled, while harmful substances and heavy metals aretreated by an environmentally friendly method.If you want to find out more information about ourrecycling program, please contact your local LG vendor ora corporate representative of LG. We set our vision and policies on a cleaner world byselecting the issue of the global environment as a task forcorporate improvement. Please visit our website for moreinformation about our ‘green’ policies.http://www.lge.com/about/environment/html/Recycling.jspInformationen zur Erhaltung der UmweltIm Jahr 1994 verkündete LGE die 'LG Declaration for aCleaner Environment' (LG Erklärung für eine sauberereUmwelt). Seitdem dient dieses Ideal als führendes Prinzipdes Unternehmens. Diese Erklärung war die Basis für dieDurchführung von umweltfreundlichen Aktivitäten, wobei wirtschaftliche,umweltbezogene und soziale Aspekte in die Überlegungen mit einbezogen wurden.Wir fördern Aktivitäten zum Schutz der Umwelt und dieEntwicklung unserer Produkte ist darauf ausgerichtet,unserem Konzept bezüglich Umweltfreundlichkeit gerechtzu werden. Wir sind darauf bedacht, den Anteil der in unserenProdukten enthaltenen schädlichen Materialien zuminimieren. So ist in unseren Monitoren beispielsweisekein Kadmium zu finden.Informationen zum Thema RecyclingDieser Monitor enthält Teile, die umweltschädlich seinkönnen. Es ist unbedingt erforderlich, dass der Monitorrecycelt wird, nachdem er außer Dienst gestellt wurde.Bei LGE. werden alle ausrangierten Monitore in einemunter umweltbezogenen Aspekten geeigneten Verfahrenrecycelt. Augenblicklich sind weltweit mehrereRücknahme- und Recyclingsysteme im Einsatz. VieleTeile werden wieder verwendet und recycelt. SchädlicheSubstanzen und Schwermetalle werden durchumweltverträgliche Verfahren behandelt.Falls Sie mehr über unser Recyclingprogramm erfahrenmöchten, wenden Sie sich bitte an Ihren lokalen LG-Händler oder einen Unternehmensvertreter von LG. Wir richten unsere Firmenpolitik auf eine sauberereUmwelt hin aus, indem wir umweltspezifische Aspekte alswichtigen Punkt in die Weiterentwicklung unseresUnternehmens einfließen lassen. ZusätzlicheInformationen über unsere ‘grüne’ Firmenpolitik erhaltenSie auf unserer Website.http://www.lge.com/about/environment/html/Recycling.jspInformation sur la protection del’environnementLGE. a publié sa 'Déclaration en faveur d’unenvironnement plus propre' en 1994 et celle-ci est restée,depuis lors, un principe directeur de notre entreprise.Cette déclaration a servi de base à notre réflexion et nousa permis de prendre en compte à la fois les aspectséconomiques et sociaux de nos activités, tout enrespectant l’environnement.Nous encourageons les activités en faveur de lapréservation de l’environnement et c’est dans cet esprit que nous développons nos produits : nous réduisons auminimum les matières dangereuses qui entrent dans leurcomposition et l’on ne trouve pas de cadmium, parexemple, dans nos moniteurs.Information sur le recyclageCe moniteur peut contenir des composants qui présententun risque pour l’environnement. Il est donc important quecelui-ci soit recyclé après usage.LGE. traite les moniteurs en fin de cycle conformément àune méthode de recyclage respectueuse del’environnement. Nous reprenons nos produits et lesrecyclons dans plusieurs sites répartis dans le mondeentier. De nombreux composants sont réutilisés etrecyclés, et les matières dangereuses, ainsi que lesmétaux lourds, sont traités selon un procédé écologique.Si vous souhaitez plus de renseignements sur notreprogramme de recyclage, veuillez contacter votrerevendeur LG ou un l’un de nos représentants. Nous voulons agir pour un monde plus propre et croyonsau rôle de notre entreprise dans l’amélioration del’environnement. Pour plus de renseignements sur notrepolitique “verte”, rendez visite à notre site :http://www.lge.com/about/environment/html/Recycling.jspDeutschFrançais
05Regulatory Information cont. Informazioni per la tutela dell’ambienteLa LGE. ha annunciato nel 1994 la cosiddetta 'LGDeclaration for a Cleaner Environment' (Dichiarazione diLG a favore di un ambiente più pulito), un ideale che daallora funge da principio ispiratore della gestioneaziendale. La dichiarazione rappresenta il fondamento checonsente di intraprendere attività a favore dell'ambientetenendo conto degli aspetti economici, ambientali esociali.Noi della LG, promuoviamo attività a favore dellatutela dell'ambiente sviluppando appositamente i nostriprodotti per cogliere il concetto del rispetto dell’ambienteriducendo i materiali dannosi presenti nei nostri prodotti.Ad esempio nei nostri monitor non è presente il cadmio.Informazioni per il riciclaggioIl monitor può presentare componenti che potrebberorisultare eventualmente dannosi per l'ambiente. Èimportante che il monitor sia riciclato al termine del suoutilizzo.La LGE. gestisce tutti i monitor di rifiuto con un metodo diriciclaggio soddisfacente dal punto di vista ambientale. Intutto il mondo sono attualmente in funzione numerosisistemi di riciclaggio e recupero. I diversi componenti sonoriutilizzati e riciclati, mentre le sostanze dannose e i metallipesanti vengono trattati con un metodo rispettosodell’ambiente.Se si desiderano maggiori informazioni in merito alprogramma di riciclaggio, è consigliabile rivolgersi alproprio rivenditore LG o ad un rappresentante aziendaledella LG. Noi della LG impostiamo la nostra visione e le nostrepolitiche a favore di un mondo più pulito ponendo laquestione dell'ambiente dal punto di vista globale comeuna mansione rivolta al miglioramento della nostraazienda. Vi invitiamo a visitare il nostro sito internet perulteriori informazioni sulla nostra politica “verde”.http://www.lge.com/about/environment/html/Recycling.jspInformación para la conservación medioambientalLGE. presentó la 'Declaración para un entorno más limpiode LG' en 1994 y este ideal ha servido para guiar nuestrosprincipios empresariales desde entonces. La Declaraciónes la base que nos ha permitido llevar a cabo tareas querespetan el medio ambiente siempre teniendo en cuentaaspectos sociales, económicos y medioambientales.Promocionamos actividades orientadas a la conservacióndel medio ambiente y desarrollamos nuestros productosespecíficamente para que se ajusten a la filosofía queprotege el entorno. Reducimos al máximo el uso de materiales de riesgo ennuestros productos. Un ejemplo de ello es la ausenciatotal de cadmio en nuestros monitores.Información para el reciclajeEste monitor puede contener piezas que entrañen riesgosmedioambientales. Es importante reciclar este monitordespués de su utilización.LGE. trata todos los monitores usados siguiendo unmétodo de reciclaje que no daña al entorno. Contamoscon diversos sistemas de recuperación y reciclaje quefuncionan a nivel mundial en la actualidad. Es posiblereciclar y reutilizar muchas de las piezas, mientras que lassustancias dañinas y los metales pesados se tratansiguiendo un método que no perjudique al medioambiente. Si desea obtener más información acerca delprograma de reciclaje, póngase en contacto con suproveedor local de LG o con un representante empresarialde nuestra marca. Basamos nuestra visión y nuestras políticas en un mundomás limpio y para ellos optamos por un entorno globalcomo tarea principal de nuestra evolución como empresa.Visite nuestra página Web para obtener más informaciónsobre nuestras políticas ecológicas.http://www.lge.com/about/environment/html/Recycling.jspInformações relacionadas à preservaçãoambientalA LGE. anunciou a 'LG Declaration for a CleanerEnvironment' (Declaração da LG para um ambiente maislimpo) em 1994 e esse ideal tem servido desde entãocomo um princípio administrativo de orientação. ADeclaração é a base que nos tem permitido realizaratividades favoráveis ao ambiente com consideraçãoatenta aos aspectos econômicos, ambientais e sociais.Promovemos atividades de preservação ambiental edesenvolvemos nossos produtos para englobarItalianoEspanõlPortuguês
06Regulatory Information cont. especificamente o conceito de favorável ao ambiente. Reduzimos os materiais perigosos contidos em nossosprodutos. Por exemplo, não há cádmio em nossosmonitores.Informações relacionadas à reciclagemEste monitor pode conter peças que podem representarriscos ao ambiente. É importante que ele seja recicladoapós o uso.A LGE. cuida de todos os monitores descartados atravésde um método de reciclagem agradável ao ambiente. Hávários sistemas de devolução e reciclagem atualmenteem operação no mundo. Muitas peças serão reutilizadase recicladas e as substâncias nocivas e os metaispesados passarão por tratamento através de um métodofavorável ao ambiente.Para obter mais informações sobre nosso programa dereciclagem, entre em contato com seu fornecedor LGlocal ou com um representante corporativo da LG. Definimos nossa visão e nossas políticas relacionadas aum mundo mais limpo selecionando a questão doambiente global como uma tarefa de aprimoramentocorporativo. Visite nosso site para obter mais informaçõessobre nossas políticas de meio ambiente.http://www.lge.com/about/environment/html/Recycling.jspInformatie met betrekking tot het behoud vanhet milieuLGE. publiceerde in 1994 de 'LG Declaration for a CleanerEnvironment' (de LG-verklaring met betrekking tot eenschoner milieu). Deze verklaring en het ideaal van eenschoner milieu fungeren sindsdien als een bestuurlijkeleidraad voor onze onderneming. Op basis van dezeverklaring ontplooien wij milieuvriendelijke activiteiten,waarbij er zowel met sociale en economische aspecten,als met milieuaspecten zorgvuldig rekening wordtgehouden.Wij ondersteunen activiteiten die zijn gericht op hetbehoud van het milieu en wij houden bij het ontwikkelenonze producten specifiek rekening met de milieuvriendelijkheid van onze producten. Wij minimaliseren het gebruik van schadelijke stoffen inonze producten. Er wordt bijvoorbeeld geen cadmiumverwerkt in onze monitors.NederlandsInformatie met betrekking tot recyclingDeze monitor bevat materialen die schadelijk zoudenkunnen zijn voor het milieu. Het is belangrijk dat dezemonitor aan het einde van zijn levensduur wordtgerecycled.LGE. verwerkt alle afvalmonitors via een milieuvriendelijkerecyclingmethode. Hiervoor worden er momenteelwereldwijd verscheidene inname- en recyclingsystemengehanteerd. Een groot aantal onderdelen wordt opnieuwgebruikt en gerecycled, waarbij schadelijke stoffen enzware metalen volgens een milieuvriendelijke methodeworden verwerkt.Voor meer informatie over ons recyclingprogramma kunt ucontact opnemen met uw plaatselijke LG-vertegenwoordiger of een LG-vestiging. Onze visie en ons beleid met betrekking tot een schonerewereld vloeien voort uit het feit dat wij het milieu hebbenaangemerkt als een onderwerp dat speciale aandachtverdient binnen onze onderneming. Bezoek onze websitevoor meer informatie over ons 'groene' beleid.http://www.lge.com/about/environment/html/Recycling.jsp»ÌÙÓχˆËˇ ÔÓ Óı‡Ì ÓÍÛʇ˛˘ÂÈ Ò‰˚¬ 1994 „Ó‰Û ÍÓÔÓ‡ˆËˇ LGE ÓÔÛ·ÎËÍÓ‚‡Î‡'ƒÂÍ·‡ˆË˛ LG ÔÓ Óı‡Ì ÓÍÛʇ˛˘ÂÈ Ò‰˚',ÍÓÚÓ‡ˇ Ò ÚÂı ÔÓ ÒÎÛÊËÚ ÓÒÌÓ‚Ì˚Ï ÔË̈ËÔÓÏÛÔ‡‚ÎÂÌˡ. Õ‡ ÓÒÌÓ‚Â ˝ÚÓÈ ‰ÂÍ·‡ˆËË Ï˚ ÒÏÓ„ÎËÔ‰ÔËÌˇÚ¸ ‰ÂÈÒڂˡ, Ó·ÂÒÔ˜˂‡˛˘Ë ·ÂÁÓÔ‡ÒÌÓÒÚ¸ ÓÍÛʇ˛˘ÂÈ Ò‰˚, Û‰ÂΡˇ ÔË ˝ÚÓωÓÎÊÌÓ ‚ÌËχÌË ˝ÍÓÌÓÏ˘ÂÒÍËÏ, ˝ÍÓÎӄ˘ÂÒÍËÏ ËÒӈˇθÌ˚Ï ‡ÒÔÂÍÚ‡Ï.Ã˚ ÒÚËÏÛÎËÛÂÏ ‰ÂˇÚÂθÌÓÒÚ¸ ÔÓ Óı‡ÌÂÓÍÛʇ˛˘ÂÈ Ò‰˚, Û‰ÂΡˇ ÓÒÓ·Ó ‚ÌËχÌËÂ‡Á‡·ÓÚÍ ̇¯ÂÈ ÔÓ‰Û͈ËË ‚ ÒÓÓÚ‚ÂÚÒÚ‚ËË ÒÍÓ̈ÂÔˆËÂÈ ˝ÍÓÎӄ˘ÂÒÍÓÈ ·ÂÁÓÔ‡ÒÌÓÒÚË. Ã˚ Ò‚Ó‰ËÏ Í ÏËÌËÏÛÏÛ ÒÓ‰ÂʇÌË ÓÔ‡ÒÌ˚ı‚¢ÂÒÚ‚ ‚ ̇¯ÂÈ ÔÓ‰Û͈ËË. Õ‡ÔËÏÂ, ‚ ̇¯ËıÏÓÌËÚÓ‡ı ‚˚ Ì ̇ȉÂÚ ͇‰Ïˡ.»ÌÙÓχˆËˇ ÔÓ ÛÚËÎËÁ‡ˆËË ÓÚıÓ‰Ó‚›ÚÓÚ ÏÓÌËÚÓ ÏÓÊÂÚ ÒÓ‰Âʇڸ ÍÓÏÔÓÌÂÌÚ˚,ÍÓÚÓ˚ ÏÓ„ÛÚ Ì‡ÌÂÒÚË Û˘Â· ÓÍÛʇ˛˘ÂÈ Ò‰Â.Russian
07Regulatory Information cont. EPA(EPA applied model only)ENERGY STARis a set of power-saving guidelinesissued by the U.S. Environmental ProtectionAgency(EPA).NOM MARK (Mexico only)ÕÂÓ·ıÓ‰ËÏÓ ÛÚËÎËÁËÓ‚‡Ú¸ ÏÓÌËÚÓ ÔÓÒÎÂËÒÔÓθÁÓ‚‡Ìˡ.KÓÔÓ‡ˆËˇ LGE ÔÂÂ‡·‡Ú˚‚‡ÂÚ ‚Ò ·‡ÍÓ‚‡ÌÌ˚ÂÏÓÌËÚÓ˚ Ò ÔÓÏÓ˘¸˛ ˝ÍÓÎӄ˘ÂÒÍË ÔËÂÏÎÂÏÓ„ÓÏÂÚÓ‰‡ ÛÚËÎËÁ‡ˆËË ÓÚıÓ‰Ó‚. œÓ ‚ÒÂÏÛ ÏËÛ‰ÂÈÒÚ‚Û˛Ú ÒËÒÚÂÏ˚ ÛÚËÎËÁ‡ˆËË ÓÚıÓ‰Ó‚ Ë ‚ÓÁ‚‡Ú‡ËÒÔÓθÁÓ‚‡ÌÌÓÈ ÔÓ‰Û͈ËË. ÃÌÓ„Ë ÍÓÏÔÓÌÂÌÚ˚·Û‰ÛÚ ‚ÚÓ˘ÌÓ ËÒÔÓθÁÓ‚‡Ì˚ Ë ÛÚËÎËÁËÓ‚‡Ì˚, ‚ ÚÓ‚ÂÏˇ Í‡Í ‚‰Ì˚ ‚¢ÂÒÚ‚‡ Ë ÚˇÊÂÎ˚ ÏÂÚ‡ÎÎ˚·Û‰ÛÚ Ó·‡·ÓÚ‡Ì˚ Ò ÔÓÏÓ˘¸˛ ˝ÍÓÎӄ˘ÂÒÍËÔËÂÏÎÂÏÓ„Ó ÏÂÚÓ‰‡.«‡ ·ÓΠÔÓ‰Ó·ÌÓÈ ËÌÙÓχˆËÂÈ ÔÓ Ì‡¯ÂÈÔÓ„‡ÏÏ ÛÚËÎËÁ‡ˆËË ÓÚıÓ‰Ó‚ Ó·‡˘‡ÈÚÂÒ¸ ÍÏÂÒÚÌÓÏÛ ÔÓÒÚ‡‚˘ËÍÛ ËÎË Ô‰ÒÚ‡‚ËÚÂβ ÍÓÔÓ‡ˆËË LG. Ã˚ ÓËÂÌÚËÛÂÏÒˇ ̇ Ó·ÂÒÔ˜ÂÌË ˝ÍÓÎӄ˘ÂÒÍÓÈ·ÂÁÓÔ‡ÒÌÓÒÚË, ÒÚ‡‚ˇ Ò· ˆÂθ˛ „ÎÓ·‡Î¸ÌÛ˛ Á‡˘ËÚÛÓÍÛʇ˛˘ÂÈ Ò‰˚. ƒÓÔÓÎÌËÚÂθÌÛ˛ ËÌÙÓχˆË˛Ó ̇¯ÂÈ ÔÓÎËÚËÍ ÔÓ Óı‡Ì ÓÍÛʇ˛˘ÂÈ Ò‰˚ ‚˚ÏÓÊÂÚ ̇ÈÚË Ì‡ ̇¯ÂÏ Ò‡ÈÚÂ:http://www.lge.com/about/environment/html/Recycling.jspAs an ENERGY STAR Partner LGE U. S.A.,Inc. has determined that this productmeets the ENERGY STAR guidelines forenergy efficiency.
08Regulatory Information cont. 1.When this crossed-out wheeled bin symbol is attachedto a product it means the product is covered by theEuropean Directive 2002/96/EC. 2.All electrical and electronic products should bedisposed of separately from the municipal wastestream via designated collection facilities appointed bythe government or the local authorities. 3.The correct disposal of your old appliance will helpprevent potential negative consequences for theenvironment and human health.4.For more detailed information about disposal of yourold appliance, please contact your city office, wastedisposal service or the shop where you purchased theproduct.Disposal of your old appliance1.Quando su un prodotto è riportato il simbolo di1.När den här symbolen med en överkryssadsoptunna på hjul sitter på en produkt innebär detatt den regleras av European Directive2002/96/EC.2.Alla elektriska och elektroniska produkter börkasseras via andra vägar än de som finns förhushållsavfall, helst via för ändamålet avseddauppsamlingsanläggningar som myndigheternautser.3.Om du kasserar din gamla apparat på rätt sättså bidrar du till att förhindra negativakonsekvenser för miljön och människors hälsa.4.Mer detaljerad information om kassering av dingamla apparat kan får av kommunen,renhållningsverket eller den butik där du köpteprodukten.1.Als het symbool met de doorgekruiste verrijdbareafvalbak op een product staat, betekent dit dathet product valt onder de Europese Richtlijn2002/96/EC.2.Elektrische en elektronische producten mogenniet worden meegegeven met het huishoudelijkafval, maar moeten worden ingeleverd bijspeciale inzamelingspunten die door de lokale oflandelijke overheid zijn aangewezen.3.De correcte verwijdering van uw oude toestelhelpt negatieve gevolgen voor het milieu en demenselijke gezondheid voorkomen.Smaltimento delle apparecchiature obsoleteKassering av din gamla apparatUw oude toestel wegdoen1.Ce symbole, représentant une poubelle surroulettes barrée d'une croix, signifie que leproduit est couvert par la directive européenne2002/96/EC.2.Les éléments électriques et électroniquesdoivent être jetés séparément, dans les vide-ordures prévus à cet effet par votre municipalité. 3.Une élimination conforme aux instructions aideraà réduire les conséquences négatives et risqueséventuels pour l'environnement et la santéhumaine.4.Pour plus d'information concernant l'éliminationde votre ancien appareil, veuillez contacter votremairie, le service des ordures ménagères ouencore la magasin où vous avez acheté ceproduit.Élimination de votre ancien appareilun bidone della spazzatura barrato da una crocesignifica che il prodotto è coperto dalla direttivaeuropea 2002/96/EC.2.Tutti i prodotti elettrici ed elettronici dovrebberoessere smaltiti separatamente rispetto allaraccolta differenziata municipale, medianteimpianti di raccolta specifici designati dalgoverno o dalle autorità locali.3.Il corretto smaltimento delle apparecchiatureobsolete contribuisce a prevenire possibiliconseguenze negative sulla salute umana esull'ambiente.4.Per informazioni più dettagliate sullo smaltimentodelle apparecchiature obsolete, contattare ilcomune, il servizio di smaltimento rifiuti o ilnegozio in cui è stato acquistato il prodotto. EnglishFrenchItalianSwedishDutchWEEE (for Europe )
Regulatory Information cont. 091.Wenn dieses Symbol eines durchgestrichenenAbfalleimers auf einem Produkt angebracht ist,unterliegt dieses Produkt der europäischenRichtlinie 2002/96/EC.2.Alle Elektro- und Elektronik-Altgeräte müssengetrennt vom Hausmüll über dafür staatlichvorgesehenen Stellen entsorgt werden.3.Mit der ordnungsgemäßen Entsorgung des altenGeräts vermeiden Sie Umweltschäden und eineGefährdung der persönlichen Gesundheit. 4.Weitere Informationen zur Entsorgung des altenGeräts erhalten Sie bei der Stadtverwaltung,beim Entsorgungsamt oder in dem Geschäft, woSie das Produkt erworben haben. 1.ŸÙ·Ó ¤Ó· ÚÔ˚fiÓ ‰È·ı¤ÙÂÈ ÙÔ ‰‡Ì‚ÔÏÔ ÂÓfi˜‰È·ÁÚ·Ì̤ÓÔ˘ οϷıÔ˘ ·ÔÚÚÈÌÌ¿ÙˆÓ, ÙfiÙ ÙÔ ÚÔ˚fiÓηχÙÂÙ·È ·fi ÙËÓ E˘Úˆ·˚΋ O‰ËÁ›· 2002/96/EOK.2.H ·fiÚÚÈ„Ë fiÏˆÓ ÙˆÓ ËÏÂÎÙÚÈÎÒÓ Î·È ËÏÂÎÙÚÔÓÈÎÒÓÚÔ˚fiÓÙˆÓ Ú¤ÂÈ Ó· Á›ÓÂÙ·È ¯ˆÚÈÛÙ¿ ·fi Ù· ÁÂÓÈοÔÈÎȷο ·ÔÚÚ›ÌÌ·Ù· ̤ۈ ηıÔÚÈṲ̂ӈÓÂÁηٷÛÙ¿ÛÂˆÓ Û˘ÏÏÔÁ‹˜ ·ÔÚÚÈÌÌ¿ÙˆÓ, ÔÈ Ôԛ˜¤¯Ô˘Ó ‰ËÌÈÔ˘ÚÁËı› ›Ù ·fi ÙËÓ Î˘‚¤ÚÓËÛË ‹ ·fi ÙȘÙÔÈΤ˜ ·Ú¯¤˜.3.H ÛˆÛÙ‹ ·fiÚÚÈ„Ë Ù˘ ·ÏÈ¿˜ Û·˜ Û˘Û΢‹˜ ı·‚ÔËı‹ÛÂÈ ÛÙËÓ ·ÔÙÚÔ‹ Èı·ÓÒÓ ·ÚÓËÙÈÎÒÓ Û˘ÓÂÈÒÓˆ˜ ÚÔ˜ ÙÔ ÂÚÈ‚¿ÏÏÔÓ Î·È ÙËÓ ˘Á›· ÙÔ˘ ·ÓıÚÒÔ˘.4.°È· ÈÔ ÏÂÙÔÌÂÚ›˜ ÏËÚÔÊÔڛ˜ Û¯ÂÙÈο Ì ÙËÓ·fiÚÚÈ„Ë Ù˘ ·ÏÈ¿˜ Û·˜ Û˘Û΢‹˜, ÂÈÎÔÈÓˆÓ‹ÛÙ ÌÂÙÔ ·ÚÌfi‰›Ô ÙÔÈÎfi ÁÚ·Ê›Ô, ˘ËÚÂÛ›· ‰È¿ıÂÛ˘ ÔÈÎÈ·ÎÒÓ·ÔÚÚÈÌÌ¿ÙˆÓ ‹ ÙÔ Ì·Á·Í› ·fi ÙÔ ÔÔ›Ô ·ÁÔÚ¿Û·Ù ÙÔÚÔ˚fiÓ.1.Tämä merkki tuotteessa tarkoittaa, että tuotekuuluu sähkö- ja elektroniikkalaiteromustaannetun EU-direktiivin 2002/96/EYsoveltamisalaan.2.Kaikki elektroniset laitteet ovat ongelmajätettä, joten ne on toimitettava paikalliseenkeräyspisteeseen.3.Vanhan laitteen asianmukainen hävittäminen ehkäisee mahdollisia ympäristöön ja terveyteen kohdistuvia haittavaikutuksia.4.Lisätietoa vanhan laitteen hävittämisestä saat ottamalla yhteyden paikallisiin viranomaisiin,kierrätyskeskukseen tai myymälään, josta ostit laitteen.1.Når der er et tegn med et kryds over enskraldespand, betyder det, at produktet eromfattet af EU-direktiv 2002/96/EC.2.Alle elektriske og elektroniske produkter skalsmides ud et andet sted end gennem denkommunale affaldsordning ved hjælp af specielleindsamlingsfaciliteter, der er organiseret af staten1.Si en un producto aparece el símbolo de un contenedorde basura tachado, significa que éste se acoge a laDirectiva 2002/96/CE.2.Todos los aparatos eléctricos o electrónicos se debendesechar de forma distinta del servicio municipal derecogida de basura, a través de puntos de recogidadesignados por el gobierno o las autoridades locales.3.La correcta recogida y tratamiento de los dispositivosinservibles contribuye a evitar riesgos potenciales para elmedio ambiente y la salud pública.4.Para obtener más información sobre cómo deshacerse desus aparatos eléctricos y electrónicos viejos, póngase encontacto con su ayuntamiento, el servicio de recogida debasuras o el establecimiento donde adquirió el producto. Vanhojen laitteiden hävittäminenEntsorgung von AltgerätenSådan smider du dit gamle apparat ud∞fiÚÚÈ„Ë Ù˘ ·ÏÈ¿˜ Û·˜ Û˘Û΢‹˜Cómo deshacerse de aparatos eléctricos yelectrónicos viejoseller de lokale myndigheder.3.Korrekt bortskaffelse af dit gamle apparat er medtil at forhindre mulige skadevirkninger på miljøetog menneskelig sundhed. 4.Mere detaljerede oplysninger om bortskaffelse afdit gamle apparat kan fås ved at kontakte ditlokale kommunekontor, renovationsselskab ellerden butik, hvor du købte produktet. FinnishGermanDanishGreekSpanish4.Wilt u meer informatie over de verwijdering vanuw oude toestel? Neem dan contact op met uwgemeente, de afvalophaaldienst of de winkelwaar u het product hebt gekocht.
Regulatory Information cont. 10 PortugueseSlovakCzechCroatianHungarianPolish
Regulatory Information cont. 11EstonianLatvianLithuanian

Navigation menu