LG Electronics USA 60PC1DUE Plasma Display Panel User Manual 38289U0527F LG

LG Electronics USA Plasma Display Panel 38289U0527F LG

Contents

User Manual 1

Please read this manual carefully before operating your set. Retain it for future reference.Record model number and serial number of the set. See the label attached on the back cover and quote this information to your dealer when you require service.ENERGYSTAR is a set of power-savingguidelines issued by the U.S.Environmental Protection Agency(EPA).As an ENERGY STARPartner LGE U. S. A.,Inc.has determined that thisproduct meets the ENER-GY STAR guidelines forenergy efficiency. P/NO : 38289U0527FPrinted in KoreaOWNER’S MANUALLCD TVMODELS: 26LC2DPLASMA TVMODELS: 50PC3D60PC1DInternet Home Page : http://www.lge.comhttp://www.lg.ca
2WarningWARNING:TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USERSERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL.The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user tothe presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of suffi-cient magnitude to constitute a risk of electric shock to persons.The exclamation point within an equilateral triangle is intended to alert the user to the presence ofimportant operating and maintenance (servicing) instructions in the literature accompanying the appli-ance.NOTE TO CABLE/TV INSTALLER:This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the National ElectricCode (U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cableground shall be connected to the grounding system of the building, as close to the point of the cable entry as prac-tical.REGULATORY INFORMATIONThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference ina residential installation. This equipment generates, uses and can radiate radio frequency energy and, if notinstalled and used in accordance with the instructions, may cause harmful interference to radio communications.However, there is no guarantee that interference will not occur in a particular installation. If this equipment doescause harmful interference to radio or television reception, which can be determined by turning the equipment offand on, the user is encouraged to try to correct the interference by one or more of the following measures:- Reorient or relocate the receiving antenna.- Increase the separation between the equipment and receiver.- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.- Consult the dealer or an experienced radio/TV technician for help.Any changes or modifications not expressly approved by the party responsible for compliance could void theuser’s authority to operate the equipment. CAUTION:Do not attempt to modify this product in any way without written authorization from LG Electronics Corporation.Unauthorized modification could void the user’s authority to operate this product.COMPLIANCE:The responsible party for this device compliance is:Zenith Electronics Corporation1-201-816-2000Marked and Distributed in the United States by LG Electronics U.S.A., Inc.1000 Sylvan Avenue, Englewood Cliffs, NJ 07632http://www.zenith.comCAUTIONRISK OF ELECTRIC SHOCK DO NOT OPENWWarningarning
3Safety InstructionsWARNING :To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on theapparatus.IMPORTANT SAFETY INSTRUCTIONS1. Read these instructions.2. Keep these instructions.3. Heed all warnings. 4. Follow all instructions.5. Do not use this apparatus near water.6. Clean only with a dry cloth.7. Do not block any of the ventilation openings. Install inaccordance with the manufacturer’s instructions.8. Do not install near any heat sources such as radiators,heat registers, stoves, or other apparatus (includingamplifiers) that produce heat.9. Do not defeat the safety purpose of the polarized orgrounding type plug. A polarized plug has two bladeswith one wider than the other. A grounding type plug hastwo blades and a third grounding prong. The wide bladeor the third prong is provided for your safety. When theprovided plug does not fit into your outlet, consult anelectrician for replacement of the obsolete outlet.10. Protect the power cord from being walked on orpinched particularly at plugs, convenience recepta-cles, and the point where they exit from the apparatus.11. Only use the attachments / accessories specified bythe manufacturer.Safety InstructionsSafety InstructionsOwner's Manual
4Safety Instructions12. Use only with a cart, stand, tripod, bracket, or tablespecified by the manufacturer, or sold with the appa-ratus. When a cart is used, use caution when movingthe cart / apparatus combination to avoid injury fromtip-over.13. Unplug this apparatus during lightning storms or whenunused for long periods of time.14. Refer all servicing to qualified service personnel.Servicing is required when the apparatus has beendamaged in any way, such as power supply cord orplug is damaged, liquid has been spilled or objectshave fallen into the apparatus, the apparatus has beenexposed to rain or moisture, does not operate normal-ly, or has been dropped.15. DISCONNECTING DEVICE FROM MAINSMain plug is the disconnecting device.Theplug must remain redily operable.On Disposal a. The fluorescent lamp used in this product contains a small amount of mercury.b. Do not dispose of this product with general household waste.Disposal of this product must be carried out in accordance to the regulations of your local authority.Note- If the TV feels cold to the touch, there may be a small “flicker” when when it is turned on. This is normal, there is noth-ing wrong with TV.- Some minute dot defects may be visible on the screen, appearing as tiny red, green, or blue spots. However, they haveno adverse effect on the monitor's performance.- Avoid touching the LCD screen or holding your finger(s) against it for long periods of time. Doing so may produce sometemporary distortion effects on the screen.CAUTION concerning the Power CordMost appliances recommend they be placed upon a dedicated circuit; that is, a single outlet circuit which powers only thatappliance and has no additional outlets or branch circuits. Check the specification page of this owner's manual to be certain.Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords, frayed power cords,or damaged or cracked wire insulation are dangerous. Any of these conditions could result in electric shock or fire.Periodically examine the cord of your appliance, and if its appearance indicates damage or deterioration, unplug it, discon-tinue use of the appliance, and have the cord replaced with an exact replacement part by an authorized servicer.Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, closed in a door, orwalked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the appliance.
5ContentsContentsContentsIntroductionInstallationOperation27 Turning on the TV27 Volume Adjustment27 Channel Selection27 On Screen Menus Language Selection28 On Screen Menus Selection and Adjustment29 EZ Scan (Channel Search)29 Manual Scan30 Channel Edit31 DTV Signal Strength31 Input Source32 Input Label33 Auto Picture Control(EZ Picture)33~34 Color Temperature Control35 XD36 Advanced-Cinema 3:2 Mode / Black Level37 Video Reset38 Audio Language38 Auto Volume Leveler(EZ SoundRite)39 Auto Sound Control(EZ Sound)39~40 Manual Sound Control (EZ Sound-User option)41 Balance41 TV Speakers On/Off Setup2 Warnings3~4 Safety Instructions7 Accessories 8 Controls (Model Name: 50PC3D / 60PC1D)9 Connection Options (Model Name: 50PC3D / 60PC1D)10 Controls (Model Name: 26LC2D)11 Connection Options (Model Name: 26LC2D)12~13 Remote Control Key Functions14 Attaching the TV to a wall15 Desktop Pedestal Installation16 Antenna or Cable Connection17~18 VCR Setup18 External AV Source Setup19~20 DVD Setup21~22 HDSTB Setup23 AV Out Setup23 Digital Audio Output24~26 PC SetupSetup MenuOptionsVideo MenuOptionsAudio MenuOptionsBasic operationExternalEquipmentConnections
6ContentsReference42 Auto Clock Setup42 Manual Clock Setup43 On/Off Timer Setup43 Sleep Timer44 Auto Off45 Aspect Ratio Control46 Caption/Text47 Caption Option47 Low Power ( 50PC3D / 60PC1D only)48 ISM (Image Sticking Minimization) Method (50PC3D / 60PC1D only)49~50 Parental Lock Setup51~56 External Control Device Setup57~58 IR Codes59 Programming the Remote60~61 Programming Codes62~63 Troubleshooting Checklist64 Maintenance65 Product SpecificationsOption MenuFeaturesLock Menu OptionsOperationTime MenuOptions
7IntroductionAccessoriesAccessoriesIntroductionIntroductionOwner’s Manual75ΩRound CablePower CordEnsure that the following accessories are included with your TV. If any accessory is missing, please contact thedealer from where you purchased the product.1.5V1.5VENTER VOLFLASHBACKMUTECHTIMERSAPMENU123569VENTER TVTVINPUT INPUTDVDRATIOEXITVOLEZ SOUNDINFOADJUSTEZ PICFLASHBACKMUTECHTIMERCCSAPMENUVCRPOWER1234567890FAVCOMP1MODECOMP2 HDMIRGB-PCRemote Control /Batteries2-eye-bolts 2-TV brackets2-Wall brackets2-TV Bracket BoltsFor 26LC2DFor 50PC3D / 60PC1DTwister HolderArrange the wires with the twister holder.CableManagement(Refer p.18)Polishing ClothPolish the TV with the cloth.Slightly wipe stained spot on theexterior only with the cleansingcloths for the product exterior ifthere is stain or fingerprint on sur-face of the exterior.Do not wipe roughly when remov-ing stain. Please be cautious ofthat excessive power may causescratch or discoloration. 2-Wall brackets
ENTER8IntroductionControls (Model Name: 50PC3D / 60PC1D)Controls (Model Name: 50PC3D / 60PC1D)- This is a simplified representation of front panel. - This picture shown below may be somewhat different from your TV.POWERButtonINPUTButtonENTERButtonVOLUME(FF,GG)ButtonsCHANNEL(EE,DD)ButtonsPower Standby IndicatorIlluminates red in stand-by mode.Illuminates green whenthe set is switched on.MENUButton ENTERENTERRemote Control SensorCHCHVOLOLENTERENTERMENUMENUINPUTINPUTCHANNEL (D, E)ButtonsVOLUME (F,G)ButtonsENTER ButtonMENU ButtonINPUT ButtonRemote Control SensorPower/Standby Indicator• illuminates red in standby mode.• illuminates green when the set is switched on.(Power) Button50PC3D60PC1D
9IntroductionConnection Options Connection Options (Model Name: 50PC3D / 60PC1D)(Model Name: 50PC3D / 60PC1D)- This picture shown below may be somewhat different from your TV.VIDEOAUDIOVIDEOAUDIO( )S-VIDEOAV IN 1AV OUTCOMPONENT INVIDEOAUDIOVIDEOAUDIO( )S-VIDEOAV IN 1AV OUTCOMPONENT INAV IN 2/MONORHDMI INVIDEOVIDEOAUDIOAUDIOVIDEOVIDEOAUDIOAUDIOMONO( )S-VIDEOS-VIDEOAV IN 1AV IN 1AV OUTAV OUTANTENNA/CABLE IN(CONTROL & SERVICE)RGB INCOMPONENT INCOMPONENT INOUTOPTICALVIDEOAUDIOVIDEOAUDIO( )S-VIDEOAV IN 1AV OUTCOMPONENT IN1(DVI)2SERVICES-VIDEO InputProvides better picture qualitythan the video input.AUDIO InputConnections are available for lis-tening to stereo sound from anexternal device.VIDEO InputConnects the video signal from avideo device.COMPONENT INConnect a component video/audio device tothese jacks.AV OUTConnect a second TV or monitor.AV (Audio/Video) IN 1 Connect audio/video output from an externaldevice to these jacks.S-VIDEO Connect S-Video out from an S-VIDEO device.ANTENNA/CABLE INConnect over-the air signals to this jack.DIGITAL AUDIO OUTConnect digital audio from various types of equip-ment. Note: In standby mode, these ports do not work.HDMI INConnect a HDMI signal to 1(DVI) or 2.Or DVI (VIDEO)signal to the 1(DVI) port with aDVI to HDMI cable.RGB IN (PC)Connect the monitor output from a PC to theappropriate input port.Remote Control PortConnect your wired remote control.AUDIO IN (RGB/DVI)Connect the monitor output from a PC to theappropriate input port.RS-232C IN (CONTROL & SERVICE) PORTConnect to the RS-232C port on a PC.Power Cord SocketFor operation with AC power. Caution: Never attempt to operate the TV on DC power.1241789102345567839106
IntroductionControls (Model Name: 26LC2D)Controls (Model Name: 26LC2D)- This is a simplified representation of front panel. - This picture shown below may be somewhat different from your TV.10RCHCHVOLVOLENTERENTERMENUMENUINPUTINPUTCHANNEL (D, E)ButtonsVOLUME (F,G)ButtonsENTER ButtonMENU ButtonINPUT ButtonRemote Control SensorPower/Standby Indicator• illuminates red in standbymode.• illuminates green when the setis switched on.(Power) ButtonSwivel Stand (26LC2D Only)Swivel Stand (26LC2D Only)R- The TV can be conveniently swivelled on its stand 30°tothe left or right to provide the optimum viewing angle.
11IntroductionConnection Options Connection Options (Model Name: 26LC2D)(Model Name: 26LC2D)- This picture shown below may be somewhat different from your TV.VIDEOAUDIOVIDEOAUDIO( )S-VIDEOAV IN 1AV OUTCOMPONENT INAC INVIDEOAUDIOVIDEOAUDIO( )S-VIDEOAV IN 1AV OUTCOMPONENT INVIDEOAUDIOVIDEOAUDIO( )S-VIDEOAV IN 1AV OUTCOMPONENT INVIDEOVIDEOAUDIOAUDIOVIDEOVIDEOAUDIOAUDIOMONO( )S-VIDEOS-VIDEOAV IN 1AV IN 1AV OUTAV OUTANTENNA/CABLE INRS-232C IN(CONTROL & SERVICE)RGB IN(PC)COMPONENT INCOMPONENT INDIGITAL AUDIOOUTOPTICALSERVICEHDMI IN1(DVI)2S-VIDEO InputProvides better picture quality than thevideo input.VIDEO InputConnects the video signal from a videodevice.AUDIO InputConnections are available for listening tostereo sound from an external device.COMPONENT INConnect a component video/audio device tothese jacks.AV OUTConnect a second TV or monitor.AV (Audio/Video) IN 1 Connect audio/video output from an externaldevice to these jacks.S-VIDEO Connect S-Video out from an S-VIDEO device.ANTENNA/CABLE INConnect over-the air signals to this jack.Connect cable signals to this jack.DIGITAL AUDIO OUTConnect digital audio from various types of equip-ment. Note: In standby mode, these ports do not work.HDMI INConnect a HDMI signal.Or DVI (VIDEO)signal to the this port with aHDMI to DVI cable.RGB IN (PC)Connect the monitor output from a PC to theappropriate input port.Remote Control PortConnect your wired remote control.AUDIO IN (RGB/DVI)Connect the monitor output from a PC to theappropriate input port.RS-232C IN (CONTROL & SERVICE) PORTConnect to the RS-232C port on a PC.SERVICEPower Cord SocketFor operation with AC power. Caution: Never attempt to operate the TV on DC power.12417891023455678391161110
12IntroductionRemote Control Key FunctionsRemote Control Key FunctionsENTER TVTVINPUTDVDRATIOEXITVOLEZ SOUNDINFOADJUSTEZ PICFLASHBACKMUTECHTIMERCCSAPMENUVCRPOWER1234567890FAVCOMP1MODECOMP2 HDMIRGB-PCINPUT TV INPUTPOWERRATIO+/-THUMBSTICK(Up/Down/LeftRight)ENTERVOLUME UP/DOWNMUTEFLASHBKCHANNELUP/DOWNFAVIn AV 1-2, Component 1-2, RGB-PC, HDMI1/DVI orHDMI2 input sources, screen returns to the last TVchannel.External input modes rotate in regular sequence: TV,AV1-2, Component 1-2, RGB-PC, HDMI1/DVI or HDMI2.(AV 1-2, Component 1-2, RGB-PC , HDMI1/DVI orHDMI2 input sources are linked automatically, only ifthese are connected.)Turns your TV or any other programmed equipment onor off, depending on the mode.Change the aspect ratio. GGpp..4455Adjust brightness on screen.It turns to the default settings brightness by changingmode source.Navigate the on-screen menus and adjust the system set-tings to your preference.Accepts your selection or displays the current mode.Increase/decrease the sound level.Switch the sound on or off. GGpp..2277Tune to the last channel viewed.Select available channels.Input the channel number.Scroll through the programmed Favorite channels.NUMBER button
13IntroductionInstalling Batteries■Open the battery compartment cover on theback side and install the batteries matching cor-rect polarity (+with +,-with -).■Install two 1.5V AA batteries. Don’t mix old orused batteries with new ones.■Close cover.TV, DVD, VCRCOMP1COMP2HDMIRGB-PCEZ PICEZ SOUNDADJUSTINFOEXITCCMENUSAPTIMERSelects the remote operating mode: TV, VCR, DVD. Select other operating modes, for theremote to operate external devices.Directly, select Component1 input.Directly, select Component2 input.Directly, select HDMI input.Directly, select RGB input.Adjust the factory preset picture depend on the viewing environment.(red) GGpp..3333Select the appropriate type of sound for type of program.(green) GGpp..3399Adjust the screen position, size, and phase in PC mode.(yellow) GGpp..2266Display information at the top of the screen. (blue)Control video cassette recorders or DVD players.Clear all on-screen displays and return to TV viewing from any menu.Select a closed caption. GGpp..4466(*In DTV/CADTV mode GGpp..4466)Displays the main menu. Analog mode: Selects MTS sound(Mono, Stereo, and a SAP)DTV mode: Change the audio language.Select the amount of time before your TV turns off automatically. GGpp..4433VCR/DVD control buttons■Use a remote control up to 7 meters distance and30 degree (left/right) within the receiving unitscope.■Dispose of used batteries in a recycle bin to pre-serve environment.OK TVTVINPUTINPUTDVDARCEXITPIP PR + PIP INPUTSWAPPIP PR -SLEEPLISTI/IIMENUTEXT PIPSIZEPOSITIONVCRPOWERRemote control effective rangeOK TVTVINPUTINPUTDVDARCEXITPIP PR + PIP INPUTSWAPPIP PR -Q.VIEWSLEEPLISTI/IIMENUTEXT PIPSIZEPOSITIONVCRPOWEROK TVTVINPUTINPUTDVDARCEXITPIP PR + PIP INPUTSWAPPIP PR -Q.VIEWSLEEPLISTI/IIMENUTEXT PIPSIZEPOSITIONVCRPOWER
14IntroductionATTACHING THE TV TO A WALLWe recommend that you set up the TV close to a wall so it cannot fall over if pushed backwards. Additionally, we recommend that the TV be attached to a wall so it cannot be pulled in a forward direction,potentially causing injury or damaging the product. Caution: Please make sure that children don’t climb on or hang from the TV. ■Insert the eye-bolts (or TV brackets and bolts) to tighten the product to the wall as shown in the pic-ture. * If your product has the bolts in the eye-bolts position, loosen the bolts.Secure the wall brackets with the bolts (not provided as parts of the product, must purchase sepa-rately) on the wall. Match the height of the bracket that is mounted on the wall to the holes in theproduct.Ensure the eye-bolts or brackets are tightened securely.■Use a sturdy rope (not provided as parts of the product, must purchaseseparately) to tie the product. It is safer to tie the rope so it becomeshorizontal between the wall and the product.
15InstallationInstallationInstallationFor proper ventilation, allow a clearance of 4inches on each side from the wall.4 inches4 inchesGGEnsure adequate ventilation by following the clearance recommendations.CAUTION4 inches 4 inchesPower SupplyShort-circuitBreaker■This picture shown below may be somewhat different from your TV.GROUNDINGEnsure that you connect the earth ground wire to prevent possible electric shock. If grounding methodsare not possible, have a qualified electrician install a separate circuit breaker. Do not try to ground the unit by connecting it to telephone wires, lightening rods, or gas pipes.DESKTOP PEDESTAL INSTALLATION
16InstallationAntenna Or Cable ConnectionMulti-family Dwellings/Apartments(Connect to wall antenna socket)Single-family Dwellings /Houses(Connect to wall jack for outdoor antenna)Outdoor AntennaWall Antenna SocketVHF AntennaUHF AntennaRF Coaxial Wire (75 ohm)Turn clockwise to tighten.VIDEOAUDIOVIDEOAUDIO( )S-VIDEOAV IN 1AV OUTANTENNA/CABLE INCOMPONENT INDIGITAL AUDIO OUTOPTICALVIDEOAUDIOVIDEOAUDIO( )S-VIDEOAV IN 1AV OUTCOMPONENT INBronze WireBe careful not to bend the bronze wire whenconnecting the antenna.Analog and Digital TV signals provided on antenna- Antenna or Cable Service without a Cable Box Connection.- For optimum picture quality, adjust antenna direction if needed.Analog and DTV signals provided on two separate antennasCable TV Wall JackRF Coaxial Wire (75 ohm)Bronze WireBronze WireTurn clockwise to tighten.AntennaRF Coaxial Wire (75 ohm)•In a poor signal area to improve picture quality, purchase and install a sig-nal amplifier.•If the antenna needs to be split for two TV’s, install a “2-Way Signal Splitter”in the connections.•If the antenna is not installed properly, contact your dealer for assistance.VIDEOAUDIOVIDEOAUDIO( )S-VIDEOAV IN 1AV OUTANTENNA/CABLE INCOMPONENT INDIGITAL AUDIO OUTOPTICALVIDEOAUDIOVIDEOAUDIO( )S-VIDEOAV IN 1AV OUTCOMPONENT INExternal Equipment ConnectionsExternal Equipment ConnectionssignalamplifierVIDEOAUDIOVIDEOAUDIO( )S-VIDEOAV IN 1AV OUTANTENNA/CABLE INCOMPONENT INDIGITAL AUDIO OUTOPTICALVIDEOAUDIOVIDEOAUDIO( )S-VIDEOAV IN 1AV OUTCOMPONENT INNOTE: All cables shown are not included with the TVCable TV Wall JackRF Coaxial Wire (75 ohm)Turn clockwise to tighten.Analog and Digital TV signals provided on cableVIDEOAUDIOVIDEOAUDIO( )S-VIDEOAV IN 1AV OUTANTENNA/CABLE INCOMPONENT INDIGITAL AUDIO OUTOPTICALVIDEOAUDIOVIDEOAUDIO( )S-VIDEOAV IN 1AV OUTCOMPONENT IN
17Installation- To avoid picture noise (interference), leave an adequate distance between the VCR and TV.- Typically a frozen still picture from a VCR. If the 4:3 picture format is used; the fixed images on the sidesof the screen may remain visible on the screen.VCR SetupWhen connecting with an antennaVIDEOAUDIOVIDEOAUDIO( )S-VIDEOAV IN 1AV OUTCOMPONENT INDIGITAL AUDIO OUTOPTICALS-VIDEO OUTIN(R) AUDIO (L) VIDEO34OUTPUTSWITCHANT OUTANT INANTENNA/ANTENNA/CABLE INCABLE INREMOTEREMOTECONTROL INCONTROL INRS-232C INRS-232C IN(CONTROL(CONTROL & SER & SERVICE)VICE)RGB IN(PC)(PC)AUDIO INAUDIO IN(RGB/DVI)(RGB/DVI)VIDEOAUDIOVIDEOAUDIO( )S-VIDEOAV IN 1AV OUTCOMPONENT INDIGITAL AUDIO OUTOPTICALSERVICESERVICEHDMI IN 1(DVI)1(DVI)2When connecting with a RCA cableVIDEOAUDIOVIDEOAUDIO( )S-VIDEOAV IN 1AV OUTCOMPONENT INDIGITAL AUDIO OUTOPTICALS-VIDEOOUTIN(R) AUDIO (L) VIDEO34OUTPUTSWITCHANT OUTANT INHDMI / DVI IN ANTENNA/CABLE INREMOTECONTROL INRS-232C IN(CONTROL & SERVICE)RGB IN(PC)AUDIO IN(RGB/DVI)VIDEOVIDEOAUDIOAUDIOVIDEOVIDEOAUDIOAUDIOMONO( )S-VIDEOS-VIDEOAV IN 1AV OUTCOMPONENTCOMPONENT INDIGITAL AUDIO OUTOUTOPTICALPTICALSERVICEVCR123Connect the AUDIO/VIDEO jacks between TVand VCR. Match the jack colors (Video = yellow,Audio Left = white, and Audio Right = red) Insert a video tape into the VCR and press PLAYon the VCR. (Refer to the VCR owner’s manual.) Select AV1 input source using the INPUT buttonon the remote control.- If connected to AV IN2, select AV2 input source.•If you have a mono VCR, connect the audio cable from the VCR to the AUDIO L/MONO jack of theset.11234Connect the RF antenna out socket of the VCR tothe Antenna socket on the set.Connect the antenna cable to the RF antenna insocket of the VCR.Set VCR output switch to 3 or 4 and then tune TVto the same channel number.Insert a video tape into the VCR and press PLAYon the VCR. (Refer to the VCR owner’s manual.) VCR12
18InstallationWhen connecting with an S-Video cableVIDEOAUDIOAUDIOVIDEOAUDIOAUDIOMONO( )S-VIDEOS-VIDEOAV IN 1AV OUTCOMPONENTCOMPONENT INDIGITDIGITALAL AUDIO AUDIO OUTOPTICALPTICALS-VIDEOOUTIN(R) AUDIO (L) VIDEO34OUTPUTSWITCHANT OUTANT INHDMI / DVI IN ANTENNA/CABLE INREMOTECONTROL INRS-232C IN(CONTROL & SERVICE)RGB IN(PC)AUDIO IN(RGB/DVI)VIDEOAUDIOVIDEOAUDIO( )S-VIDEOAV IN 1AV OUTCOMPONENT INDIGITAL AUDIO OUTOPTICALSERVICEVCR112234Connect the S-VIDEO output of the VCR to the S-VIDEO input on the set. The picture quality isimproved; compared to normal composite (RCAcable) input.Connect the audio outputs of the VCR to theAUDIO input jacks on the set.Insert a video tape into the VCR and press PLAYon the VCR. (Refer to the VCR owner’s manual.) Select AV1 input source with using the INPUTbutton on the remote control.- If connected to AV IN2, select AV2 input source.Do not connect to both Video and S-Video at the same time. In the event that you connectboth Video and the S-Video cables, only the S-Video will work.RLAUDIO VIDEOCamcorderVideo Game Set1123Connect the AUDIO/VIDEO jacks between TVand external equipment. Match the jack colors(Video = yellow, Audio Left = white, and AudioRight = red).Select AV2 input source with using the INPUTbutton on the remote control.- If connected to AV IN1 input, select AV1 inputsource.Operate the corresponding external equipment.Refer to external equipment operating guide.External AV Source Setup•This TV finds the connected input sourcesautomatically for AV1, AV2, Component 1-2,RGB, HDMI1/DVI and HDMI2 sources areconnected.
19InstallationDVD SetupWhen connecting with a S-Video cableHDMI / DVI IN ANTENNA/CABLE INVIDEOVIDEOAUDIOAUDIOVIDEOVIDEOAUDIOAUDIOMONO( )S-VIDEOS-VIDEOAV IN 1V IN 1AV OUTV OUTCOMPONENTCOMPONENT IN INDIGITDIGITALAL AUDIO AUDIO OUTOUTOPTICALPTICALVIDEOAUDIOCOMPONENT INS-VIDEO (R) AUDIO (L)DVD1122345Connect the S-VIDEO output of the DVD to the S-VIDEO input on the set.Connect the audio outputs of the DVD to the AUDIO input jacks on the set.Turn on the DVD player, insert a DVD.Select AV1 input source with using the INPUT button on the remote control.- If connected to AV IN2, select AV 2 input source.Refer to the DVD player's manual for operating instructions.When connecting with a HDMI cable123Connect the HDMI output of the DVD to theHDMI/DVI IN jack on the set.Select HDMI/DVI input source with using theINPUT button on the remote control.Refer to the DVD player's manual for operatinginstructions.ANTENNA/ANTENNA/CABLE INCABLE INVIDEOAUDIOVIDEOAUDIO( )S-VIDEOAV IN 1AV OUTCOMPONENT INDIGITAL AUDIO OUTOPTICALVIDEOAUDIOCOMPONENT INHDMI-DVD OUTPUTHDMI IN HDMI IN 1(DVI)2DVD1•TV can receive the video and audio signalsimultaneously with using a HDMI cable.•If the DVD supports Auto HDMI function, theDVD output resolution will be automaticallyset to 1280x720p.•If the DVD does not support Auto HDMI, youneed to set the output resolution appropriate-ly. To get the best picture quality, adjust theoutput resolution of the DVD to 1280x720p.
20InstallationWhen connecting with a component cable12345Connect the video outputs (Y, PB, PR) of the DVD to the COMPONENT IN VIDEO jacks on the set.Connect the audio outputs of the DVD to the COMPONENT IN AUDIO jacks on the set.Turn on the DVD player, insert a DVD.Select Component 1 input source with using the INPUT button on the remote control.- If connected to COMPONENT 2, select Component 2 input source.Refer to the DVD player's manual for operating instructions.•Component Input portsTo get better picture quality, connect a DVD player to the component input ports as shown below.Y PBPRComponent ports on the TVYYYYPbB-YCbPBPrR-YCrPRVideo output ports on DVD playerHDMI / DVI IN ANTENNA/CABLE INVIDEOAUDIOVIDEOAUDIO( )S-VIDEOAV IN 1AV OUTCOMPONENT INDIGITAL AUDIO OUTOPTICALVIDEOAUDIOAUDIOCOMPONENTCOMPONENT INBR(R) AUDIO (L)DVD1 2

Navigation menu