LG Electronics USA 60PC1DUE Plasma Display Panel User Manual 38289U0527F LG

LG Electronics USA Plasma Display Panel 38289U0527F LG

Contents

User Manual 2

21Installation- This TV can receive Digital Over-the-air/Cable signals without an external digital set-top box. However, ifyou do receive Digital signals from a digital set-top box or other digital external device, refer to the figureas shown below.HDSTB SetupWhen connecting with a HDMI cable123Connect the HDMI output of the digital set-topbox to the HDMI/DVI IN jack on the set.Select HDMI/DVI input source with using theINPUT button on the remote control.Turn on the digital set-top box. (Refer to theowner’s manual for the digital set-top box.) Digital Set-top Box•TV can receive the video and audio signal simultaneously using a HDMI cable.•If the digital set-top box supports Auto HDMI function, output resolution of the digital set-top box willbe automatically set to 1280x720p.•If the digital set-top box does not support Auto HDMI, you need to set the output resolution appro-priately. To get the best picture quality, adjust the output resolution of the digital set-top box to1280x720p.RGB INREMOTECONTROL INRS-232C IN(CONTROL & SERVICE)RGB IN(PC)AUDIO IN(RGB/DVI)HDMI-DTV OUTPUTREMOTECONTROL INRS-232C IN(CONTROL & SERVICE)RGB IN(PC)AUDIO IN(RGB/DVI)REMOTEREMOTECONTROL INCONTROL INRS-232C INRS-232C IN(CONTROL(CONTROL & SER & SERVICE)VICE)RGB INRGB IN(PC)(PC)AUDIO INAUDIO IN(RGB/DVI)(RGB/DVI)VIDEOAUDIOVIDEOAUDIO( )S-VIDEOAV IN 1AV OUTCOMPONENT INDIGITAL AUDIO OUTOPTICALSERVICESERVICESERVICEHDMI IN HDMI IN 1(DVI)2HDMI IN 1(DVI)21When connecting with a Component cable1234Connect the video outputs (Y, PB, PR) of the digi-tal set-top box to the COMPONENT IN VIDEOjacks on the set.Connect the audio output of the digital set-top boxto the COMPONENT IN AUDIO jacks on the set.Turn on the digital set-top box. (Refer to theowner’s manual for the digital set-top box.) Select Component 1 input source with using theINPUT button on the remote control.- If connected to COMPONENT 2, selectComponent 2 input source.BR(R) AUDIO (L)RGB INREMOTECONTROL INRS-232C IN(CONTROL & SERVICE)RGB IN(PC)AUDIO IN(RGB/DVI)HDMI / DVI IN REMOTECONTROL INRS-232C IN(CONTROL & SERVICE)RGB IN(PC)AUDIO IN(RGB/DVI)HDMI / DVI IN REMOTECONTROL INRS-232C IN(CONTROL & SERVICE)RGB IN(PC)AUDIO IN(RGB/DVI)VIDEOVIDEOAUDIOAUDIOVIDEOVIDEOAUDIOAUDIOMONO( )S-VIDEOS-VIDEOAV IN 1V IN 1AV OUTV OUTCOMPONENTCOMPONENT INDIGITDIGITALAL AUDIO AUDIO OUTOUTOPTICALPTICALSERVICESERVICESignal480i480p/720p/1080iComponent1/2YesYesHDMI/DVINoYes21Digital Set-top Box
22InstallationWhen connecting with a HDMI to DVI cable1234Connect the DVI output of the digital set-top box to the HDMI/DVI IN jack on the set.Connect the audio outputs of the set-top box to the AUDIO (RGB/DVI) jack on the set.Turn on the digital set-top box. (Refer to the owner’s manual for the digital set-top box.) Select HDMI/DVI input source with using the INPUT button on the remote control.RGB IN(R) AUDIO (L)DVI-DTV OUTPUTREMOTECONTROL INRS-232C IN(CONTROL & SERVICE)RGB IN(PC)AUDIO IN(RGB/DVI)REMOTEREMOTECONTROL INCONTROL INRS-232C INRS-232C IN(CONTROL(CONTROL & SER & SERVICE)VICE)RGB INRGB IN(PC)(PC)AUDIO INAUDIO IN(RGB/DVI)(RGB/DVI)REMOTECONTROL INRS-232C IN(CONTROL & SERVICE)RGB IN(PC)AUDIO IN(RGB/DVI)VIDEOAUDIOVIDEOAUDIO( )S-VIDEOAV IN 1AV OUTCOMPONENT INDIGITAL AUDIO OUTOPTICALSERVICESERVICESERVICEHDMI IN 1(DVI)2HDMI IN HDMI IN 1(DVI)1(DVI)2Digital Set-top Box12• If the digital set-top box has a DVI output and no HDMI output, a separated audio connection is nec-essary.•If the digital set-top box supports Auto DVI function, the output resolution of the digital set-top box willbe automatically set to 1280x720p.•If the digital set-top box does not support Auto DVI, you need to set the output resolution appropri-ately. To get the best picture quality, adjust the output resolution of the digital set-top box to1280x720p.
23InstallationDigital Audio Output123Connect one end of an optical cable to the TVDigital Audio Optical Output port.Connect the other end of the optical cable to thedigital audio optical input on the audio equipment.See the external audio equipment instructionmanual for operation. When connecting with external audio equip-ments, such as amplifiers or speakers, pleaseturn the TV speakers off. (Refer to p.41)VIDEOVIDEOAUDIOAUDIOVIDEOVIDEOAUDIOAUDIOMONO( )S-VIDEOS-VIDEOAV IN 1V IN 1AV OUTV OUTCOMPONENT INDIGITDIGITALAL AUDIO AUDIO OUTOUTOPTICALPTICAL- Send the TV’s audio to external audio equipment (stereo system) via the Digital Audio Output Optical port.CAUTIONDo not look into the optical output port. Looking at the laser beam may damage your vision.1/2AV Out Setup12Connect the second TV or monitor to the TV’s AVOUTPUT jacks. See the Operating Manual of the second TV ormonitor for further details regarding that device’sinput settings.S-VIDEO IN(R) AUDIO (L)VIDEOVIDEOVIDEOAUDIOAUDIOVIDEOVIDEOAUDIOAUDIOMONO( )S-VIDEOS-VIDEOAV IN 1V IN 1AV OUTV OUTCOMPONENTCOMPONENT INDIGITDIGITALAL AUDIO AUDIO OUTOUTOPTICALPTICAL- The TV has a special signal output capability which allows you to hook up a second TV or monitor.1/2 •Component 1-2, RGB-PC, HDMI/DVI, DTVinput sources cannot be used for Monitor out.• We recommend to use the video and audiooutput jacks for VCR recording.
24Installation- This TV provides Plug and Play capability, meaning that the PC adjusts automatically to the TV's settings. PC SetupWhen connecting with a D-sub 15 pin cable1234Connect the RGB output of the PC to the RGB(PC) jack on the set.Connect the PC audio outputs to the AUDIO(RGB/DVI) jack on the set.Turn on the PC and the set. Select RGB-PC input source with using theINPUT button on the remote control.(R) AUDIO (L)RGB-PC OUTPUTREMOTECONTROL INCONTROL INRS-232C INRS-232C IN(CONTROL(CONTROL & SER & SERVICE)VICE)RGB IN(PC)AUDIO INAUDIO IN(RGB/DVI)(RGB/DVI)HDMI / DVI IN REMOTECONTROL INRS-232C IN(CONTROL & SERVICE)RGB IN(PC)AUDIO IN(RGB/DVI)SERVICE12PCWhen connecting with a HDMI to DVI cable1234Connect the DVI output of the PC to the HDMI/DVI IN jack on the set.Connect the audio outputs of the PC to the AUDIO (RGB/DVI) jack on the set.Turn on the PC and the set. Select HDMI/DVI input source with using the INPUT button on the remote control.(R) AUDIO (L)DVI-PC OUTPUTREMOTECONTROL INRS-232C IN(CONTROL & SERVICE)RGB IN(PC)AUDIO IN(RGB/DVI)REMOTEREMOTECONTROL INCONTROL INRS-232C IN(CONTROL & SERVICE)RGB INRGB IN(PC)AUDIO IN(RGB/DVI)SERVICESERVICEHDMI IN HDMI IN 1(DVI)1(DVI)2PC• If the PC has a DVI output and no HDMI output, a separated audio connection is necessary.•If the PC does not support Auto DVI, you need to set the output resolution appropriately. To get thebest picture quality, adjust the output resolution of PC graphics card's output resolution to1024x768, 60Hz.12
25Installation1. Depending on the graphics card, DOS mode maynot work if a HDMI to DVI Cable is in use.2. When Source Devices connected with HDMI/DVIInput, output PC Resolution (VGA, SVGA, XGA,WXGA), Position and Size may not fit toScreen.Press the ADJUST button to adjust thescreen Position of TV SET and contact an PCgraphics card service center.3. When Source Devices connected with HDMI/DVIInput, output TV SET Resolution (480p, 720p,1080i. 1080p) and TV SET Display fit EIA/CEA-861-B Specification to Screen. If not, refer to theManual of HDMI/DVI Source Devices or contactyour service center.4. In case HDMI/DVI Source Devices is not connect-ed Cable or poor cable connection, "NO SIGNAL"OSD display in HDMI/DVI Input. In case that VideoResolution is not supported TV SET output inHDMI/DVI Source Devices, "INVALID FORMAT"OSD display. Refer to the Manual of HDMI/DVISource Devices or contact your service center.5. Check the image on your TV. There may be noiseassociated with the resolution, vertical pattern,contrast or brightness in PC, HDMI/DVI mode. Ifnoise is present, change the PC or HDMI/DVImode to another resolution, change the refreshrate to another rate or adjust the brightness andcontrast on the menu until the picture is clear. If therefresh rate of the PC graphic card can not bechanged, change the PC graphic card or consultthe manufacturer of the PC graphic card.6. Avoid keeping a fixed image on the TV's screen fora long period of time. The fixed image may becomepermanently imprinted on the screen.7. The synchronization input form for Horizontal andVertical frequencies is separate.Supported Display Resolution (RGB-PC, HDMI/DVI Mode)Resolution640x350720x400640x480HorizontalFrequency (kHz)31.46831.46931.46937.87970.0870.0859.9460.31VerticalFrequency (Hz)Resolution*720x480*1280x720HorizontalFrequency (kHz)31.46931.50044.9645.0033.7233.7559.9460.0059.9460.0059.9460.00VerticalFrequency (Hz)1280x768 47.747.747.148.36360606060.001360x7681366x768800x6001024x768*1920x1080* This format is only for HDMI-DTV input.
26Installation* Adjustment for screen Resolution, Position, Size, and Phase* Initializing (Reset to original factory values)- To initialize the adjusted valuesPosition This function is to adjustpicture to left/right andup/down as you prefer. Size This function is to minimizeany vertical bars or stripesvisible on the screen back-ground. And the horizontalscreen size will alsochange. Phase This function allows you toremove any horizontal noiseand clear or sharpen theimage of characters.Resolution This function allows youselect Resolution ofXGA/WXGA.Mini Glossary- When RGB connect to PC input and select the RGB-PC, this function is used. - When HDMI/DVI connect to PC input and select HDMI/DVI input, this function is used. - After connecting RGB-PC or HDMI/DVI to PC input and checking the screen quality.Press the ADJUST button and then use DD / EEbutton to selectResolution, POSITION, SIZE, or PHASE.Press ENTER button and then use DD / EE/ FF / GG buttons tomake appropriate adjustments.• The PHASE adjustment range is -16 ~ +16.(In HDMI/DVI-PC mode, PHASE is not available.)• The SIZE adjustment range is -30 ~ +30.(In HDMI/DVI-PC mode, SIZE is not available.)Press ENTER button.123Press the ADJUST button and then use DD / EEbutton to selectthe RESET option.Press ENTER button and then use FF / GG button to select Yes.Press ENTER button.123Screen Setup for PC modeTVTVINPUTDVDRATIOEXITEZ SOUNDINFOADJUSTEZ PICTIMERCCSAPMENUVCRPOWERCOMP1MODECOMP2 HDMIRGB-PCINPUT ADJUSTTVTVINPUTDVDRATIOEZ SOUNDINFOADJUSTEZ PICVCRPOWERCOMP1MODECOMP2 HDMIRGB-PCINPUT ADJUST* When you change the resolution, select the proper resolutionin present input to see the best picture appearance.
27OperationOperationOperationBasic operationBasic operation1. First, connect power cord correctly. At this moment, the TV switches to standby mode.In standby mode to turn TV on, press the , INPUT, CH DD/ EEbutton on the TV or press the POWER, TVINPUT, INPUT, CH DD/ EE, Number (0 ~ 9) button on the remote control .2. Select the viewing source by using TV INPUT, INPUT button on the remote control.This TV is programmed to remember which power state it was last set to, even if the power cord is out. 3. When finished using the TV, press the POWER button on the remote control. The TV reverts to standby mode.1. Press the VOL DD/ EEbutton to adjust the volume.2. If you want to switch the sound off, press the MUTE button. 3. You can cancel this function by pressing the MUTE or VOL DD/ EEbutton.Press the CH DD/ EEor NUMBER buttons to select a channel number.- The menus can be shown on thescreen in the selected language.First select your language.On Screen Menus Language SelectionVolume AdjustmentTurning on the TVChannel SelectionPress the MENU button and then use DD/ EEbutton to select theOPTION menu.Press the GGbutton and then use DD/ EEbutton to select Language. Press the GGbutton and then use DD/ EEbutton to select your desiredlanguage. From this point on, the on-screen menus will be shown in theselected language.Press EXIT button to return to TV viewing or press MENU button toreturn to the previous menu.1234• If you intend to be away on vacation, disconnect the power plug from the wall power outlet.Aspect RatioCaption/TextCaption OptionLanguage GISM MethodLow PowerEnglishEspañol (Spanish)Français (French)Aspect RatioCaption/TextCaption OptionLanguageISM MethodLow Power
28OperationOn Screen Menus Selection and On Screen Menus Selection and AdjustmentAdjustment1. Press the MENU button and then DD/ EEbutton to select each menu.2. Press the GGbutton and then use DD / EE/ FF / GGbutton to display the available menus.• Your TV's OSD (On Screen Display) may differ slightly from what is shown in this manual.How to adjust the OSD screenEZ ScanManual ScanChannel EditDTV SignalInput SourceInput LabelSet IDEZ PictureColor TemperatureXDAdvancedVideo ResetAudio LanguageEZ SoundRiteEZ SoundBalanceTV SpeakerAuto ClockManual ClockOff TimerOn TimerSleep TimerAuto OffAspect RatioCaption/TextCaption OptionLanguageISM MethodLow PowerLock SystemSet PasswordBlock ChannelMovie RatingTV Rating-ChildrenTV Rating-GeneralInput Block
29OperationEZ Scan (Channel Search)Setup Menu OptionsSetup Menu OptionsPress the MENU button and then use DD / EEbutton to select the SETUP menu.Press the GGbutton and then use DD / EEbutton to select EZ Scan.Press the ENTER button to begin the channel search.Allow EZ Scan to complete the channel search cycle for ANTENNA, andCABLE.123Manual Scan- A password is required to gainaccess to Manual Scan menu ifthe Lock System is turned on.Press the MENU button and then use DD / EEbutton to select the SETUP menu.Press the GGbutton and then use DD / EEbutton to select Manual Scan.Press the GGbutton and then use DD / EEbutton to select TV, DTV, CATV,and CADTV.Press the GGbutton and then use DD / EEbutton to select channel num-ber you want to add or delete.Press the ENTER button to add or delete for the channel number.Press EXIT button to return to TV viewing or press MENU button toreturn to the previous menu.123456- Automatically finds all channelsavailable through antenna orcable inputs, and stores them inmemory on the channel list.- Run EZ Scan again after anyAntenna/Cable connection changes.- A password is required to gainaccess to EZ Scan menu if theLock System is turned on.EZ Scan GManual ScanChannel EditDTV SignalInput SourceInput LabelSet IDSelection ( Gor ) leads you to the EZ scan screen.EZ ScanManual ScanChannel EditDTV SignalInput SourceInput LabelSet IDProcessing EZ scan...TV Ch.200 channel(s) foundPress to stop thecurrent scan and startCABLE channel scan.MENU PreviousNextEZ ScanManual ScanChannel EditDTV SignalInput SourceInput LabelSet IDEZ ScanManual Scan GChannel EditDTV SignalInput SourceInput LabelSet IDSelect channel type and RF-channel number.TV GG2Press to delete thechannelTV 2-0DDEE
30Operation- There are two different ways inorder to add or delete scannedchannels. One is "Custom List"and the other is "Favorite List" inthe channel list. Both of them areavailable after EZ Scan on theSETUP menu.- A Custom List can be created bytoggling each channel on or offwith ENTER button. The chan-nels in the Custom List are dis-played in black color, and thechannels deleted from theCustom List are displayed in graycolor. Once a channel is high-lighted you can add or delete thechannel by referring to the smallwindow at the top-left corner ofthe screen.You can create yourown Favorite List. Use the FAVbutton on the remote controlwhen a channel is highlightedand then you can add or deletethe channel to/from the FavoriteList.Channel EditPress the MENU button and then use DD / EEbutton to select the SETUP menu.Press the GGbutton and then use DD / EEbutton to select Channel Edit.Press the GGbutton. You will now see a screen filled with channel num-bers and a preview picture. Use DD / EE/ FF / GG button to select a channel and then use the ENTERbutton to add or delete it. Press FAV button to add the channel to theFavorite List. The heart-mark will appear in front of that channel num-ber.Press EXIT button to return to TV viewing or press MENU button toreturn to the previous menu.12345* Custom ListEZ ScanManual ScanChannel EditDTV SignalInput SourceInput LabelSet IDEZ ScanManual ScanChannel Edit GDTV SignalInput SourceInput LabelSet IDSelection ( Gor ) leads you to the channel editscreen.
31OperationDTV Signal Strength- Shows how strong your DTV sig-nal is and whether you need toadjust your antenna or digitalcable input. The higher the signalstrength, the less likely you areto experience picture degrada-tion.- DTV Signals: Only when theinput signal is DTV or CADTV,this function is available.Press the MENU button and then use DD / EEbutton to select the SETUP menu.Press the GGbutton and then use DD / EEbutton to select DTV Signal.View the on-screen signal strength monitor to see the quality of the signalbeing received. Press EXIT button to return to TV viewing or press MENU button toreturn to the previous menu.1234- Changes the picture source soyou can watch your TV, cable TV,VCR, DVD, or any other devicesthat are connected to your TV. Input SourcePress the MENU button and then use DD / EEbutton to select the SETUP menu.Press the GGbutton and then use DD / EEbutton to select Input Source.Press the GGbutton and then use DD / EEbutton to select the source:TV, AV1, AV2, Component1, Component2, or RGB-PC, or HDMI/DVI.• To toggle RGB-PC, select RGB-PC and press GGbutton.Press EXIT button to return to TV viewing or press MENU button toreturn to the previous menu.1234Setup Menu Options continuedSetup Menu Options continuedEZ ScanManual ScanChannel EditDTV SignalInput SourceInput LabelSet IDBad Normal GoodEZ ScanManual ScanChannel EditDTV SignalInput SourceInput LabelSet IDEZ ScanManual ScanChannel EditDTV SignalInput SourceInput LabelSet IDEZ ScanManual ScanChannel EditDTV SignalInput Source GInput LabelSet IDTVAV1AV2Component1Component2RGB-PCHDMI/DVI
32Operation- Sets a label to each input sourceor lets you skip the input sourcewhich is not in use when youpress INPUT button. Input LabelPress the MENU button and then use DD / EEbutton to select the SETUP menu.Press the GGbutton and then use DD / EEbutton to select Input Label.Press the GGbutton and then use DD / EEbutton to select the source: AV1-2, Component1-2, RGB-PC or HDMI/DVI.Press the FF / GGbutton to select the label.Press EXIT button to return to TV viewing or press MENU button toreturn to the previous menu.12345EZ ScanManual ScanChannel EditDTV SignalInput SourceInput LabelSet IDEZ ScanManual ScanChannel EditDTV SignalInput SourceInput Label GSet IDAV1 Cable BoxAV2 VCRComponent1 DVDComponent2 Set Top BoxRGB-PC PCHDMI/DVI Game
33OperationVVideo Menu Optionsideo Menu OptionsAuto Picture ControlAuto Picture Control ((EZ Picture)- EZ Picture adjusts the TV for the bestpicture appearance. Select the presetvalue in the EZ Picture menu basedon the program category.- Daylight, Normal, Night Time set-tings are preset for optimum picturequality at the factory and are notadjustable.- In the User 1,and User 2 modes only,user can directly adjust the contrast,brightness, color, sharpness, tint.Press the EZ Pic button repeatedly to select the picture appear-ance setup option as shown below:Daylight, Normal, Night Time, User 1 and User 2(your own set-tings).• You can also use the VIDEO menu to adjust EZ Picture.Press the EXIT button to save and return to TV viewing . 12Color Temperature Control- Choose one of three automaticcolor adjustments. Set to warmto enhance hotter colors such asred, or set to cool to see lessintense colors with more blue.Press the MENU button and then use DD / EEbutton to select the VIDEO menu.Press the GGbutton and then use DD / EEbutton to select Color Temperature. Press the GGbutton and then use DD / EEbutton to select either Cool,Medium, or Warm.Press EXIT button to return to TV viewing or press MENU button toreturn to the previous menu.1234EZ PictureColor Temperature GXDAdvancedVideo ResetEZ PictureColor TemperatureXDAdvancedVideo ResetCoolMediumWarmUser
34OperationManual Color Temperature Control- You can also adjust the detailed settings(Red, Green, Blue) by selecting the User menu.EZ PictureColor TemperatureXDAdvancedVideo ResetRed 0 EEEZ PictureColor TemperatureXDAdvancedVideo ResetPress to confirm.MENUSelection ( Gor ) leads youto the detailed setting screen.CoolMediumWarmUser GUserRed 0 GGreen 0Blue 0Press the MENU button and then use DD / EEbutton to select theVIDEO menu.Press the GGbutton and then use DD / EEbutton to select ColorTemperature . Press the GGbutton and then use DD / EEbutton to select User .Press the GGbutton and then use DD / EEbutton to select Red,Green or Blue .Press the GGbutton and then use FF / GGbutton to make appropri-ate adjustments.• The adjustment range of Red, Green or Blue is -20~ +20.Press EXIT button to return to TV viewing or press MENU but-ton to return to the previous menu.123456
35Operation- XD is LG Electronic’s unique pictureimproving technology to display areal HD source through anadvanced dig-ital signal processingalgorithm.- When selecting EZ Picture options(Daylight, Normal and Night time),XD is automatically change to Auto.- When selecting EZ Picture options(User 1 and User 2), you canchoose the Auto / Manual and whenselecting Manual, you can adjustthe XD Contrast, XD color and XDNoise.EZ PictureColor TemperatureXDAdvancedVideo ResetEZ PictureColor Temperature XD GAdvancedVideo ResetManualXD Contrast OnXD Color OnXD Noise OnPress the MENU button and then use DD / EEbutton to select the VIDEOmenu.Press the GGbutton and then use DD / EEbutton to select XD. Press the GGbutton and then use DD / EEbutton to select Auto orManual.Press EXIT button to return to TV viewing or press MENU button toreturn to the previous menu.* Selecting the Manual1. Press the GGbutton and then use FF / GGbutton to select XDContrast, XD Color or XD Noise.XD Contrast :Optimizing the contrast automatically accordingto thebrightness of the reflection.XD Color :Adjusting the colors of the reflection automaticallyto repro-duce as closely as possible to the natural colors.XD Noise :Removing the noise up to the point where it doesnot damage the original picture.2. Use the DD / EEbutton to make appropriate adjustments.XD1234
36OperationAdvanced-Cinema 3:2 Mode / Black LevelAdvanced-Cinema 3:2 Mode / Black Level• Cinema 3:2 Mode- Set up the TV for the best pictureappearance for viewing movies.When you operate Cinema (3:2 Pull-Down Mode or Cinema Correction Mode),the TV will adjust 24 fps video from movies to 30 fps video for display (This function is only available in Analog,AV1,AV2,Component 480i mode.)• Black level- Adjusting the contrast and the brightnessof the screen using the black level of thescreen.This feature operates only in HDMI/DVIor AV1, AV2 mode.EZ PictureColor TemperatureXDAdvancedVideo ResetEZ PictureColor TemperatureXD Advanced GVideo ResetCinema 3:2 Mode OffBlack Level LowPress the MENU button and then use DD / EEbutton to select the VIDEOmenu.Press the GGbutton and then use DD / EEbutton to selectAdvanced . Press the GGbutton and then use DD / EEbutton to selectCinema 3:2 Mode or Black Level.Press EXIT button to return to TV viewing or press MENU buttonto return to the previous menu.* Selecting the Cinema 3:2 ModePress the GGbutton and thenuse DD / EEbutton to select On or Off . * Selecting the Black LevelPress the GGbutton and thenuse DD / EEbutton to select Low orHigh. LowThe reflection of the screen getsdarker.HighThe reflection of the screen getsbrighter.12345

Navigation menu