LG Electronics USA 9GW97185D3-1 Scene Gateway User Manual User Guide Rev 01 150623
LG Electronics USA Scene Gateway User Guide Rev 01 150623
User Guide-Rev.01(150623)
ENGLISH MFL68045804 Installation Dimensions 29 mm 90 mm 1. Connect the DC cable to the adapter. 2. Connect the DC adapter to gateway. And then, connect the wireless router to the gateway with LAN cable. 3. Place the gateway on the proper place and make connect power. Ensure the Power LED is on. ※Note : Initialization ● HomeKit reset Momentarily press the reset button. After then, Power LED flash 3 times. 70 mm ● Factory reset LED Operation Press and hold the reset button for over 10 seconds. After 10 seconds, all LEDs begin flashing 3 times. Power LED It turns on when power is applied. LAN LED It turns on when the LAN cable is normally connected and the gateway communicates through the LAN. SCENE GATEWAY USER'S MANUAL MANUEL DE L’UTILISATEUR MANUAL DEL USUARIO Wireless Communication LED It blinks regularly when the gateway is connected through wireless communication. Smartphone Application Download the App “LG SCENE Lighting” from Apple’s App Store or Android Market. And just run it. Specifications Troubleshooting Frequency The Power LED do not turn on. : Check whether the DC cable is properly connected to both the gateway and the adapter. The LAN LED do not turn on. : Check whether the LAN cable is properly connected. The Wireless communication LED blinks too fast. : Contact the service center or dealer that you purchased this product. WARNING / AVERTISSEMENT / ADVERTENCIA EN - Violation of warnings may lead to serious injury or death. Dimensions 90 mm ES - Hacer caso omiso de las advertencias puede provocar lesiones graves o incluso la muerte. • Utilice la potencia nominal. • Apague el suministro eléctrico antes de instalar el producto. • No instale el producto cerca de un fuego. • No someta el producto al agua. For Indoor use only Weight 70 g Dimensions (WHD) 2.8”x3.5”x1.1” (70 mm x 90 mm x 29 mm) 1. Branchez le câble CC à l'adaptateur. 2. Branchez l'adaptateur CC à la passerelle. Ensuite, associez le routeur sans fil à la passerelle avec le câble LAN. 3. Placez la passerelle à un endroit adéquat et branchez l'alimentation. Vérifiez que le voyant d'alimentation est allumé ● Réinitialisation aux paramètres d’usine Appuyez longtemps sur le bouton de réinitialisation pendant plus de 10 secondes. Une fois les 10 secondes passées, toutes les DEL se mettent à clignoter 3 fois. Voyant DEL d'alimentation Il s'allume lorsque le produit est mis sous tension. FR - Le non-respect des avertissements peut entraîner des blessures graves ou la mort. Voyant DEL de communication sans fil Il clignote régulièrement lorsque la passerelle est connectée via une communication sans fil. Dépannage Le voyant DEL d'alimentation ne s'allume pas. : Vérifiez si le câble C. C. est correctement connecté à la passerelle et à l’adaptateur. Le voyant DEL réseau ne s'allume pas. : Vérifiez que le câble réseau est correctement connecté. Le voyant DEL de communication sans fil clignote trop rapidement. : Contactez le centre de service ou le revendeur auprès duquel vous avez acheté ce produit. ● Réinitialisation du HomeKit Appuyez momentanément sur le bouton de réinitialisation. Ensuite, la DEL d’alimentation clignote 3 fois. Fonctionnement des LED Il s’active lorsque le câble LAN est bien connecté et que la passerelle communique au moyen de la connexion LAN. 70 mm Voyant DEL réseau • No instale el producto en una superficie desigual. • No lo desmonte ni lo deforme. • No lo instale cerca de materiales inflamables. • No lo exponga a la luz solar directa o a la humedad. -20 ~ +40℃ Operating condition ※Remarque : Initialisation • Do not install on an uneven surface. • Do not disassemble or deform. • Do not install nearby inflammable materials. • Do not expose to direct sunlight or moisture. ES - Hacer caso omiso de las advertencias puede provocar lesiones graves o incluso la muerte. Max. 400 mA 29 mm • Utilisez la puissance nominale. • Désactivez l'alimentation avant d'installer le produit. • N'installez pas le produit près d'une source de chaleur. • N'exposez pas le produit à l'eau. • Installez le produit sur une surface plane. • Ne pas démonter ou déformer le produit. • Ne pas installer le produit à proximité de matériaux inflammables. • Ne pas exposer le produit directement à la lumière du soleil ni à la moisissure. Current consumption Operating temperature Installation FR - Le non-respect des avertissements peut entraîner des blessures graves ou la mort. CAUTION / ATTENTION / PRECAUCIÓN line of sight 98 ft (30 m) 5 V DC (from the adapter) FRANÇAIS • Use the rated power. • Turn power off before installing the product. • Do not install the product near a fire. • Do not expose the product to water. EN - Violation of precautions may lead to light injury or product damage. 2405.0 ~ 2480.0 MHz Wireless range Operating voltage Application sur téléphone intelligent Téléchargez l’application « LG SCENE Lighting » sur l’App Store d’Apple ou sur Android Market. Et lancez-la. Caractéristiques Fréquence 2405,0~2480,0 MHz Portée sans fil Portée optique : 30 m (98 ft) Tension de fonctionnement 5 V CC (À partir d'un adaptateur.) Consommation électrique Max. 400 mA Température de fonctionnement de -20 à 40℃ (-4 à 104℉) Conditions de fonctionnement Pour utilisation en intérieur uniquement Poids 70 g (2,5 oz) Dimensions (LxHxP) 70 mm x 90 mm x 29 mm (2,8” x 3,5” x 1,1”) SPANISH Apple HomeKit Certified Dimensiones Apple HomeKit technology provides an easy, secure way to control your home’s lights, doors, thermostats, and more from your iPhone, iPad, or iPod touch. Instalación 29 mm 90 mm 1. Conecte el cable de CC al adaptador. 2. Conecte el adaptador de CC a la puerta de enlace. Después, conecte el router inalámbrico a la puerta de enlace con el cable LAN. 3. Sitúe la puerta de enlace en un lugar adecuado y conecte la alimentación. Asegúrese de que el LED de alimentación está encendido. ※Nota : Inicialización ● Restablecer HomeKit Presione momentáneamente el botón reset. Después de ello, el LED de la alimentación parpadeará 3 veces. 70 mm ● Restablecer los ajustes de fábrica Funcionamiento del LED Pulse y mantenga el botón reset durante más de 10 segundos. Pasados 10 segundos, todos los LEDs empezarán a parpadear 3 veces. LED de alimentación Se enciende cuando el dispositivo recibe alimentación. LED de LAN Aplicación para Smartphone LED de comunicación inalámbrica Descargue la App “LG SCENE Lighting” de la App Store de Apple o de Android Market. Simplemente, ejecútela. Especificaciones Solución de problemas El LED de alimentación no se enciende. : Compruebe si el cable DC está conectado correctamente tanto a la puerta de enlace como al adaptador. El LED de LAN no se enciende. : Compruebe que el cable LAN está correctamente conectado. El LED de comunicación inalámbrica parpadea demasiado rápido. : Póngase en contacto con el centro de atención al cliente o con la tienda donde adquirió el producto. Model name FCC ID IC 9GW97185D3 BEJ9GW97185D3-1 2703H-9GW97185D3 Federal Communications Commission (FCC) Statement You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures : - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation of the device of the device. FCC Caution Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment and For indoor use only, use outdoors or in other modes not covered by this manual may violate the FCC regulation and violate the user authority to use the product. FCC RF Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. “Equipment used at position in which the spaces between human body and antenna exceeded 20 cm” Industry Canada (IC) Statement Industry Canada Statement : This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions : 1) this device may not cause interference and 2) this device must accept any interference, including interference that may cause undesired operation of the device. IC Radiation Exposure Statement : This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. NOTE : THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT. • HomeKit requires an iPhone, iPad or iPod touch with iOS 8.1 or later. • Compatible iPod/iPhone/iPad models iPhone 6, iPhone 6+, iPhone 5, iPhone 5c, iPhone 5s, iPhone 4s, iPad4, iPad 3, iPad Mini 1, iPad Mini2(Mini Retina), iPad AIR, iPod touch (5th generation) Android smart phone works with Android 4.3 or later. • Compatible Android models Android 4.3, Android 4.4, Android 5 Connectivity • LG Smart Lighting can be controlled by a SCENE Gateway. • Communication between SCENE Gateway and LG Smart Lighting is secured by end-to-end encryption and authentication. • SCENE Gateway enables LG Smart Lighting to work with HomeKit technology. Legal Notice Use of the HomeKit logo means that an electronic accessory has been designed to connect specifically to iPod, iPhone, or iPad, respectively, and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards. Please note that the use of this accessory with iPod, iPhone, or iPad may affect wireless performance. Warranty & Customer Service Se enciende cuando el cable LAN está conectado con normalidad y la puerta de enlace se comunica a través del LAN. Parpadea regularmente cuando la puerta de enlace está conectada de forma inalámbrica. Smart Phone App Frecuencia 2405.0 ~ 2480.0 MHz Rango inalámbrico Campo visual 30 m Tensión de alimentación 5 V DC (Desde un adaptador.) Consumo energético Máx. 400mA Temperatura de funcionamiento de-20 a 40℃ Condiciones de uso Uso exclusivo en interior Peso 70 g Dimensiones (Alt-An-Pr) 70 mm x 90 mm x 29 mm Avis de la Federal Communications Commission (FCC) Vous êtes avisé(e) que les changements ou les modifications apportés à cette unité, non expressément approuvés par la partie responsable de la conformité, pourraient annuler le droit accordé à l’utilisateur d’exploiter cet équipement. Cet équipement a été testé et jugé conforme aux limites s’appliquant à un appareil numérique de la classe B, conformément à la partie 15 de la réglementation de la FCC. Ces limites ont été élaborées pour offrir une protection raisonnable contre les interférences nuisibles dans une installation résidentielle. Cet équipement génère, utilise et peut émettre de l’énergie de radiofréquence et, s’il n’est pas installé et utilisé conformément aux instructions du fabricant, peut provoquer des interférences dangereuses pour les communications radio. Toutefois, rien ne garantit l’absence d’interférences dans une installation particulière. Si cet équipement provoque des interférences nuisibles en ce qui concerne la réception radio ou télévision, ce qui peut être déterminé par la mise hors tension, puis sous tension de l’équipement, vous êtes invité(e) à essayer de corriger les interférences en prenant les mesures suivantes : - Réorientez ou déplacez l’antenne réceptrice. - Augmentez la distance qui sépare l’équipement et le récepteur. - Branchez l’équipement dans la prise d’un circuit différent de celui auquel est branché le récepteur. Consultez le revendeur ou un technicien radio / télévision expérimenté pour obtenir de l’aide. Avertissement FCC Tout changement ou toute modification apporté(e) à cette unité non expressément approuvé(e) par la partie responsable de la conformité pourrait annuler le droit accordé à l’utilisateur d’exploiter cet équipement. Cet appareil ne convient qu’à une utilisation intérieure. Une utilisation extérieure ou d'autres façons non couvertes par ce manuel peut constituer un non-respect de la réglementation FCC et porter atteinte aux droits de l’utilisateur à utiliser ce produit. Énoncé FCC sur l’exposition aux rayonnements de radiofréquence : Cet appareil est conforme aux limites d'exposition aux rayonnements pour un environnement non contrôlé. Les utilisateurs suivront les instructions d’exploitation spécifiques pour répondre aux exigences de conformité sur l’exposition aux radiofréquences. Notice d'Industrie Canada (IC) Avis d'Industrie Canada : Cet appareil est conforme à la norme CNR-210 des règlements d'Industrie Canada. Son fonctionnement est sujet aux deux conditions suivantes : 1) Cet appareil ne doit pas provoquer d'interférences et 2) Cet appareil doit accepter toutes les interférences, y compris celles pouvant entraîner son dysfonctionnement. Avis d'Industrie Canada sur l'exposition aux rayonnements Cet appareil est conforme aux limites d'exposition aux rayonnements d'Industrie Canada pour un environnement non contrôlé. REMARQUE : LE FABRICANT N'EST PAS RESPONSABLE DES INTERFÉRENCES RADIOÉLECTRIQUES CAUSÉES PAR DES MODIFICATIONS NON AUTORISÉES APPORTÉES À CET APPAREIL. DE TELLES MODIFICATIONS POURRAIT ANNULER L'AUTORISATION ACCORDÉE À L'UTILISATEUR DE FAIRE FONCTIONNER L'APPAREIL. • Warranty : 1 year • Manufacture Date : On the product • Customer Service : www.lg.com • Made in China
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : Yes XMP Toolkit : 3.1-701 Format : application/pdf Title : 150622_R15_MFL68045804_WIRELESS GATEWAY V2_메뉴얼 Metadata Date : 2015:06:23 10:17:46+08:00 Modify Date : 2015:06:23 10:17:46+08:00 Create Date : 2015:06:22 17:57:29+10:00 Creator Tool : Adobe Illustrator CS6 (Windows) Thumbnail Width : 256 Thumbnail Height : 120 Thumbnail Format : JPEG Thumbnail Image : (Binary data 16027 bytes, use -b option to extract) Instance ID : uuid:d930d5c6-453f-4d5f-9f3e-f2c68c465fb7 Document ID : xmp.did:5FAD69829D18E51182FC808CA8F08E5F Original Document ID : uuid:5D20892493BFDB11914A8590D31508C8 Rendition Class : proof:pdf Derived From Instance ID : uuid:56dab75f-dd9f-4557-a78a-96c5c1478185 Derived From Document ID : xmp.did:5DAD69829D18E51182FC808CA8F08E5F Derived From Original Document ID: uuid:5D20892493BFDB11914A8590D31508C8 Derived From Rendition Class : proof:pdf History Action : saved, saved History Instance ID : xmp.iid:5DAD69829D18E51182FC808CA8F08E5F, xmp.iid:5FAD69829D18E51182FC808CA8F08E5F History When : 2015:06:22 15:42:07+09:00, 2015:06:22 17:57:27+09:00 History Software Agent : Adobe Illustrator CS6 (Windows), Adobe Illustrator CS6 (Windows) History Changed : /, / Startup Profile : Print Has Visible Overprint : True Has Visible Transparency : True N Pages : 1 Max Page Size W : 221.999886 Max Page Size H : 210.001652 Max Page Size Unit : Millimeters Font Name : ArialMT, Arial-BoldMT, YDIYGO320, YDIYGO330 Font Family : Arial, Arial, -윤고딕320, -윤고딕330 Font Face : Regular, Bold, Regular, Regular Font Type : Open Type, Open Type, TrueType, TrueType Font Version : Version 5.10, Version 5.08, Version 2.00, Version 2.00 Font Composite : False, False, False, False Font File Name : arial.ttf, arialbd.ttf, 윤고딕320.ttf, 윤고딕330_0.ttf Plate Names : Cyan, Magenta, Yellow, Black Swatch Groups Group Name : Brights Swatch Groups Group Type : 1 Swatch Groups Colorants Swatch Name: C=60 M=90 Y=0 K=0 Swatch Groups Colorants Mode : CMYK Swatch Groups Colorants Type : PROCESS Swatch Groups Colorants Cyan : 60.000002 Swatch Groups Colorants Magenta : 90.000004 Swatch Groups Colorants Yellow : 0.003099 Swatch Groups Colorants Black : 0.003099 Producer : Adobe PDF library 10.01 Page Count : 2 Container Version : 11 Creator Version : 16 Creator : Adobe Illustrator(R) 16.0 For : ��츮/���/Lighting��ⷯ��������Ʈ(uri.kim@lge.com), Bounding Box : 11 -586 1260 -11EXIF Metadata provided by EXIF.tools