LG Electronics USA 9QK-DMMB0502LX Bluetooth Adapter Card User Manual
LG Electronics USA Bluetooth Adapter Card
user manual
MCSLOGIC PRODUCT APPROVAL DATASHEET PRODUCT MCSLogic Class 2 Bluetooth Module MODEL NAME MB0502LX LG P/N CUSTOMER Checked By LG Electronics Approved By Company Seal MCSLOGIC Product Approval Datasheet V0.1 Copyright 2012 MCS LOGIC Limited. All rights reserved Confidential 1/12 MCSLOGIC Revision History Version Date Revision Description 0.1 12/10/26 Initial release Product Approval Datasheet V0.1 Copyright 2012 MCS LOGIC Limited. All rights reserved Confidential 2/12 MCSLOGIC Table of Contents 1. INTRODUCTION ........................................................................................................................................................... 4 2. GENERAL FEATURES ................................................................................................................................................. 4 2.1 MODULE FEATURES .................................................................................................................................................. 4 2.2 FIRMWARE FEATURES ............................................................................................................................................. 5 3. MECHANICAL DIMENSION ...................................................................................................................................... 6 4. ELECTRICAL CHARACTERISTICS ......................................................................................................................... 7 5. PIN CONFIGURATION .............................................................................................................................................. 10 6. MB0502LX CONTROL METHOD............................................................................................................................. 11 7. APPROVAL STATEMENTS ...................................................................................................................................... 12 Product Approval Datasheet V0.1 Copyright 2012 MCS LOGIC Limited. All rights reserved Confidential 3/12 MCSLOGIC 1. Introduction MB0502LX is a fully integrated Bluetooth module. It is based on CSR’s Bluecore5-Multimedia External with specific interface design to meet LG Electronics’s needs. MB0502LX is compatible with Bluetooth specification version 3.0. It integrates RF, Baseband controller, etc., a completed Bluetooth subsystem. MB0502LX supports A2DP Sink, AVRCP Controller&Target, HFP, SPP profiles. It provides a UART interface, analog/I2S/SPDIF audio output and functional GPIO. MB0502LX can control by UART. Please refer to MB0502LX software user guide for the interfacing protocol. 2. General Features 2.1 Module Features - Operation Range (Class II) : 10 meters - Operating Temperature Range : -10℃ ~ 80℃ - Operating VDD Range : Typical 3.3V(3.0V ~ 3.6V) - Output Power : 5dBm PK - Interfaces : UART, Analog Audio Line-in, SPDIF Audio Out, Functional I/O - Internal Antenna - Compatible with Bluetooth Specification 3.0 - 64MIPS Kalimba DSP Co-Processor - 16-bit Internal Stereo CODEC - RoHS Compliant - GFSK/8DPSK sf modulation, 79 channel Product Approval Datasheet V0.1 Copyright 2012 MCS LOGIC Limited. All rights reserved Confidential 4/12 MCSLOGIC 2.2 Firmware Features - Bluetooth Stack : UnifiedStack 3.0 - Host Interface : UART - Support Profile : A2DP (Sink), AVRCP Controller/Target, HFP, SPP - Profile version : A2DP V1.2, AVRCP1.4, HFP1.6, SPP1.1 - DUT(Device Under Test) Mode Support - DFU(Device Firmware Upgrade) Support Product Approval Datasheet V0.1 Copyright 2012 MCS LOGIC Limited. All rights reserved Confidential 5/12 MCSLOGIC 3. Mechanical Dimension TOP View Mark (Unit : mm) Dimension 25.00±0.5 35.00±1.0 16.50±0.3 Mark Dimension 12.00±0.3 0.50±0.15 2.00±0.3 Mark Dimension 3.00±0.3 10.00±0.5 7.00±0.5 Mark Dimension 4.30±0.3 4.00±0.3 2.50±0.3 Product Approval Datasheet V0.1 Copyright 2012 MCS LOGIC Limited. All rights reserved Confidential Mark Dimension 3.40±0.3 1.00±0.3. 6/12 MCSLOGIC 4. Electrical Characteristics Current consumption Parameter Page Scan Inquiry and Page Scan SCO Connection HV1 SCO Connection HV3 ACL No data transfer ACL data transfer Condition Master Master Master Master Avg 3.9 40 28 30 Peak 10 Unit mA mA mA mA mA mA Input/Output Characteristics Parameter Min Max Unit Digital (UART, PIO) VIL Input Voltage Low -0.4V 0.8V VIH Input Voltage High 2.3V 3.6V VOL Output Voltage Low 0.2V VOH Output Voltage High 3.1V General Performance Parameter Frequency Range Impedance at Antenna Condition Min Type 2402 50 Product Approval Datasheet V0.1 Copyright 2012 MCS LOGIC Limited. All rights reserved Confidential Max Unit 2480 MHz Ohm 7/12 MCSLOGIC Transmitter Performance Parameter Transmit Power Condition Min Type Max Unit Peak dBm 20 dBm 1000 KHz Power density 20dB bandwidth ±2% -20 dBm ±3% -40 dBm ±4% -40 dBm 30MHz ~ 1GHz -36 dBm 1GHz ~ 12.75GHz -30 dBm 1.8GHz ~ 1.9GHz -47 dBm 5.1GHz ~ 5.3GHz -47 dBm ∆F1avg 140 175 KHz ∆F2max 115 KHz ∆F2avg / ∆F1avg 80 Initial Carrier Frequency Tolerance DH1 packet -40 40 KHz Carrier Frequency Drift DH5 packet -25 25 KHz Adjacent channel power Out-band Spurious Emission Modulation Characteristic Product Approval Datasheet V0.1 Copyright 2012 MCS LOGIC Limited. All rights reserved Confidential 8/12 MCSLOGIC Receiver Performance Parameter Condition Min Type Max Unit Sensitivity level (BER≤0.1%) Single slot (DH1 packet) -70 dBm Sensitivity level (BER≤0.1%) Multi slot (DH5 packet) -70 dBm C/Ico-channel, Input = -60dBm 11 dB C/I1MHz, Input = -60dBm dB C/I2MHz, Input = -60dBm -20 dB C/I≥3Mhz, Input = -67dBm -40 dB Image radio, Input = -67dBm -9 dB Image±1, Input = -67dBm -20 dB 30MHz ~ 2000MHz -10 2000MHz ~ 2400MHz -27 dBm 2500MHz ~ 3000MHz -27 dBm 3000MHz ~ 12.75GHz -10 dBm Input=-64dBm, n=5 -39 dBm Single slot (DH1 packet) -20 -5 dBm C/I performance (BER≤0.1%) Out-of-band Blocking (BER≤0.1%) Intermodulation (BER≤0.1%) Maximum Input Level (BER≤0.1%) Product Approval Datasheet V0.1 Copyright 2012 MCS LOGIC Limited. All rights reserved Confidential 9/12 MCSLOGIC 5. Pin Configuration Symbol Description P1 CMOS input Output supply voltage VDD_P1 Pin descriptions for the MB0502LX Module NO 10 11 12 13 14 15 16 17 18 19 20 NO Pin Name GND NRESET UART_RX UART_TX GND MUTE I2S_SCK I2S_SD_OUT I2S_SD_IN I2S_WS GND AOUT_P_L AOUT_N_L AOUT_P_R AOUT_N_R GND N/C N/C GND VDD Pin Name N/C MIC BIAS MIC INPUT AGND Volt I/O P1 P1 P1 P1 P1 P1 P1 P1 P1 P1 P1 P1 P1 P1 P1 P1 P1 P1 P1 P1 I/O Volt I/O P1 P1 P1 P1 Description DIGITAL Ground System Reset(Low Active) UART Data Input active high UART Data Output active high DIGITAL Ground General Purpose I/O Bit clock Data output Data input LR clock DIGITAL Ground Analog audio positive left Analog audio negative left Analog audio positive right Analog audio negative right DIGITAL Ground Not Connected. Not Connected. DIGITAL Ground VCC 3.3V Description Not Connected. Microphone bias Analog audio input Analog Ground Product Approval Datasheet V0.1 Copyright 2012 MCS LOGIC Limited. All rights reserved Confidential 10/12 MCSLOGIC 6. MB0502LX Control Method 1) There is UART Protocol document between Host MCU and BT Module. So you can use command/response via UART. 2) RF Test Utility First time, CSR Bluesuite program must be installed. you can use BTCli.exe and enter DUT(Device Under Test) mode. So RF equipment can inquiry and test. (reference document.) *reference document : MB0502LX_DUT_Manual.pdf 3) RF Test method RF Test tool is BlueTest.exe at CSR bluesuite program. You can see detail explanation from reference document. * reference document : BlueTest Instruction Manual.pdf Product Approval Datasheet V0.1 Copyright 2012 MCS LOGIC Limited. All rights reserved Confidential 11/12 MCSLOGIC 7. Approval Statements This device complies with Part 15 of the FCC`s Rules. Operation is subject to the following two Conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesirable operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/ TV technician for help. This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. This device should be installed and must not be co-located or operating in conjunction with any other antenna or transmitter. This device is intended only for OEM integrators under the following conditions: 1) This module may not be co-located with any other transmitters or antennas. 2) The antenna used with this module must be installed to provide a separation distance of at least 20cm from all persons. As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements with this module installed. In the event that these conditions cannot be met, then the FCC authorizations are no longer considered valid and the FCC ID cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product including this module and obtaining separate FCC authorizations. Any changed or modifications not expressly approved by the party responsible for compliance could void the user`s authority to operate this equipment. To satisfy FCC exterior labeling requirements, the following text must be placed on the exterior of the end product. Contains Transmitter module FCC ID: BEJ9QK-DMMB0502LX Product Approval Datasheet V0.1 Copyright 2012 MCS LOGIC Limited. All rights reserved Confidential 12/12
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : Yes Author : hong Create Date : 2013:01:03 13:48:27+09:00 Modify Date : 2013:01:03 13:48:27+09:00 XMP Toolkit : Adobe XMP Core 4.2.1-c041 52.342996, 2008/05/07-20:48:00 Creator Tool : PScript5.dll Version 5.2.2 Producer : Acrobat Distiller 9.0.0 (Windows) Format : application/pdf Title : Microsoft Word - MB0502LX_module spec sheet-revised Creator : hong Document ID : uuid:02371cb8-58a8-4f78-9e32-11b0d1efd19e Instance ID : uuid:894caf04-5195-4296-8889-4a24c15d038c Page Count : 12EXIF Metadata provided by EXIF.tools