LG Electronics USA 9QK-DMWB1BH5 Bluetooth Module User Manual

LG Electronics USA Bluetooth Module

User manual

User ManualPRODUCT NAME : Bluetooth Class1 ROM ModuleMODEL NAME : WB1BH5(00)-0073
User ManualPAGE :REG. DATE : 2014.10.29MODEL: WB1BH5REV. DATE : 2014.10.29REV.NO : 1.01/ 11Table of ContentsNo. Description Page1Features21Features22 Block Diagram 23 Certification condition 34 Storage Conditions 55OtiCditi55Operating Conditions56 Interface Specification 67 Pin Description 88 Outline Drawing 99 Packing Information 10©2014 LGIT. All rights reserved.
User ManualPAGE :REG. DATE : 2014.10.29MODEL: WB1BH5REV. DATE : 2014.10.29REV.NO : 1.02/ 111. FeaturesWB1BH5 is the small size and low power module for Bluetooth 4.0.WB1BH5 is based on TI CC2564B.Bluetooth 4.0 / Class ISize : 34mm x 19mm x 3.1 mmInternal PCB Printed AntennaUART with maximum rate of 4 Mbps interface2. Block DiagramDigital PCM-I2S codec interfaceSupports drivers for Windows 7, Vista, XP, 2000 and LinuxApplication : DTV, DVR, HD DVD Player, Blue-ray Disk Player, STB©2014 LGIT. All rights reserved.
User ManualPAGE :REG. DATE : 2014.10.29MODEL: WB1BH5REV. DATE : 2014.10.29REV.NO : 1.03/ 113. Certification conditionFCC approvalThe satisfy FCC exterior labeling requirements, the following text must be placed on the exterior of the end product.pContains Transmitter module FCC ID : BEJ9QK-DMWB1BH5This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. This device should be installed and operated with minimum distance 20cm between the radiating element of this device and the user. This device must not be co-located or operating in conjunction with any other antenna or transmitter. This device is intended only for OEM integrators and following statements shall be included to host user manual 1) The antenna must be installed such that 20cm is maintained between the antenna and users. 2) This module may not be co-located with any other transmitters or antennas. As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements with this module installed. In the event that these conditions cannot be met, then the FCC authorizations are no longer considered valid and the FCC ID cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product including this module and obtaining separate FCC authorizations.This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions : (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful it f i id tili tllti Thi i t t d dit di finterference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna.- Increase the separation between the equipment and receiver.C t th i t i t tl t i it diff t f-Connect the equipment into an outlet on a circuit different fromthat to which the receiver is connected.- Consult the dealer or an experienced radio/ TV technician for help.CE approvalHereby, LG declares that this device is compliance with the essential requirements and other relevant i i f di ti 1999/5/EC©2014 LGIT. All rights reserved.provisions of directive 1999/5/EC.
User ManualPAGE :REG. DATE : 2014.10.29MODEL: WB1BH5REV. DATE : 2014.10.29REV.NO : 1.04/ 11IC approvalThe host device must be labeled to display the Industry Canada certification number of the module. Contains transmitter module IC: 2703H-DMWB1BH5L di itif d' il d i t êt éti té ffi h l é d tifi ti d'I d t i C d dLe dispositif d'accueil doivent être étiquetés pour afficher le numéro de certification d'Industrie Canada du module. Contient module émetteur IC : 2703H-DMWB1BH5This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Cet appareil est conforme avec Industrie Canada exempts de licence standard RSS (s). L'opération est soumise aux deux conditions suivantes: (1) cet appareil ne peut causer d'interférences, et (2) cet appareil doit accepter toute interférence, y compris les interférences quipeuvent causer un mauvais fonctionnement de l'appareil. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users the antenna type and its gain should be so chosen that the equivalentinterference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée quivalente (p.i.r.e.) ne dépassepas l'intensité nécessaire à l'établissement d'une communication satisfaisante.This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiating element of this device and the user. NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT. Cet appareil est conforme aux limites d'exposition aux rayonnements d'Industrie Canada pour un pp p y penvironnement non contrôlé. Cet appareil doit être installé et utilisé à distance minimum de 20cm entre l'élément rayonnant de cet appareil et l'utilisateur. REMARQUE : LE FABRICANT N'EST PAS RESPONSABLE DES INTERFÉRENCES RADIOÉLECTRIQUES CAUSÉES PAR DES MODIFICATIONS NON AUTORISÉES APPORTÉES À CET APPAREIL. DE TELLES MODIFICATIONS POURRAIT ANNULER L'AUTORISATION ACCORDÉE À L'UTILISATEUR DE FAIRE FONCTIONNER L'APPAREIL ©2014 LGIT. All rights reserved.
User ManualPAGE :REG. DATE : 2014.10.29MODEL: WB1BH5REV. DATE : 2014.10.29REV.NO : 1.05/ 114. Storage ConditionsParameter Min Max UnitStorage Temperature-10+80℃Storage Temperature1080℃Storage Humidity (@ 40℃)-90 %Caution : The specifications above the Table define levels at which permanent damage to the device can occur Function operation is not guaranteed under these conditionsto the device can occur. Function operation is not guaranteed under these conditions. Operating at absolute maximum conditions for extend periods can adversely affect the long-term reliability of the device.• Other conditions1) Do not use or store modules in the corrosive atmosphere, especially where chloridegas, sulfide gas, acid, alkali, salt or the like are contained. Also, avoid exposure to moisture. 2) Store the modules where the temperatureand relative humidity do not exceed 5 to 40℃and 20 to 60%.3) Assemble the modules within 6 months.Check the soldering ability in case of 6 months over.5. Operating ConditionsParameter Min Typ Max UnitAmbient Temperature 0 - +70 ℃Operating Humidity (40℃)--85 %Supply Voltage 3.15 3.3 3.45 Vdc©2014 LGIT. All rights reserved.
User ManualPAGE :REG. DATE : 2014.10.29MODEL: WB1BH5REV. DATE : 2014.10.29REV.NO : 1.06/ 116. Interface Specification1) UARTFigure 11-1 shows the UART timing diagram. Table 11-1 lists the UART timingcharacteristics Figure 112 shows the UART data frame Table 112 describescharacteristics. Figure 11-2 shows the UART data frame. Table 11-2 describes the symbols used in Table 11-2.[ Figure 11-1. UART Timing ][ Table 11-1. UART Timing Characteristics][ Figure 11-2. Data Frame]©2014 LGIT. All rights reserved.[ Table 11-2. Data Frame Key ]
User ManualPAGE :REG. DATE : 2014.10.29MODEL: WB1BH5REV. DATE : 2014.10.29REV.NO : 1.07/ 112) PCMFigure 11-3 shows the interface timing for the PCM. Table 11-3 and Table 11-4 Lists the associated master and slave parametersLists the associated master and slave parameters.[ Figure 11-3. PCM Interface Timing ][ Table 11-3. PCM Master ]©2014 LGIT. All rights reserved.[ Table 11-4. PCM Slave ]
User ManualPAGE :REG. DATE : 2014.10.29MODEL: WB1BH5REV. DATE : 2014.10.29REV.NO : 1.08/ 117. Pin Description< TOP View > < Bottom View > 12Note.1) Recommend a Module install sequence for prevent USB device failure- Supply 3.3V power C t t d t i l (UART TX RX)12©2014 LGIT. All rights reserved.-Connect to data signal (UART TX, RX)2) Connector: 12Pin SMD Connector A
User ManualPAGE :REG. DATE : 2014.10.29MODEL: WB1BH5REV. DATE : 2014.10.29REV.NO : 1.09/ 118. Outline Drawing©2014 LGIT. All rights reserved.
User ManualPAGE :REG. DATE : 2014.10.29MODEL: WB1BH5REV. DATE : 2014.10.29REV.NO : 1.010 / 119. Packing Information©2014 LGIT. All rights reserved.
User ManualPAGE :REG. DATE : 2014.10.29MODEL: WB1BH5REV. DATE : 2014.10.29REV.NO : 1.011 / 11©2014 LGIT. All rights reserved.

Navigation menu