LG Electronics USA 9QK-DMWB1BH5 Bluetooth Module User Manual
LG Electronics USA Bluetooth Module
User manual
User Manual
PRODUCT NAME : Bluetooth Class1 ROM Module
MODEL NAME : WB1BH5
(00)-0073
User Manual
PAGE :
REG. DATE : 2014.10.29
MODEL: WB1BH5
REV. DATE : 2014.10.29
REV.NO : 1.0
1/ 11
Table of Contents
No. Description Page
1
Features
2
1
Features
2
2 Block Diagram 2
3 Certification condition 3
4 Storage Conditions 5
5
OtiCditi
5
5
O
pera
ti
ng
C
on
diti
ons
5
6 Interface Specification 6
7 Pin Description 8
8 Outline Drawing 9
9 Packing Information 10
©2014 LGIT. All rights reserved.
User Manual
PAGE :
REG. DATE : 2014.10.29
MODEL: WB1BH5
REV. DATE : 2014.10.29
REV.NO : 1.0
2/ 11
1. Features
WB1BH5 is the small size and low power module for Bluetooth 4.0.
WB1BH5 is based on TI CC2564B.
Bluetooth 4.0 / Class I
Size : 34mm x 19mm x 3.1 mm
Internal PCB Printed Antenna
UART with maximum rate of 4 Mbps interface
2. Block Diagram
Digital PCM-I2S codec interface
Supports drivers for Windows 7, Vista, XP, 2000 and Linux
Application : DTV, DVR, HD DVD Player, Blue-ray Disk Player, STB
©2014 LGIT. All rights reserved.
User Manual
PAGE :
REG. DATE : 2014.10.29
MODEL: WB1BH5
REV. DATE : 2014.10.29
REV.NO : 1.0
3/ 11
3. Certification condition
FCC approval
The satisfy FCC exterior labeling requirements, the following text must be placed on the exterior of the
end
p
roduct.
p
Contains Transmitter module FCC ID : BEJ9QK-DMWB1BH5
This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. This
device should be installed and operated with minimum distance 20cm between the radiating element of
this device and the user. This device must not be co-located or operating in conjunction with any other
antenna or transmitter.
This device is intended only for OEM integrators and following statements shall be included to host user
manual
1) The antenna must be installed such that 20cm is maintained between the antenna and users.
2) This module may not be co-located with any other transmitters or antennas.
As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM
integrator is still responsible for testing their end-product for any additional compliance requirements with
this module installed. In the event that these conditions cannot be met, then the FCC authorizations are
no longer considered valid and the FCC ID cannot be used on the final product. In these circumstances,
the OEM integrator will be responsible for re-evaluating the end product including this module and
obtaining separate FCC authorizations.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions :
(1) this device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
it f i id tili tllti Thi i t t d dit di f
i
n
t
er
f
erence
i
n a res
id
en
ti
a
l
i
ns
t
a
ll
a
ti
on.
Thi
s equ
i
pmen
t
genera
t
es, uses an
d
can ra
di
a
t
e ra
di
o
f
requency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
C t th i t i t tl t i it diff t f
-
C
onnec
t
th
e equ
i
pmen
t
i
n
t
o an ou
tl
e
t
on a c
i
rcu
it
diff
eren
t
f
rom
that to which the receiver is connected.
- Consult the dealer or an experienced radio/ TV technician for help.
CE approval
Hereby, LG declares that this device is compliance with the essential requirements and other relevant
i i f di ti 1999/5/EC
©2014 LGIT. All rights reserved.
prov
i
s
i
ons o
f
di
rec
ti
ve
1999/5/EC
.
User Manual
PAGE :
REG. DATE : 2014.10.29
MODEL: WB1BH5
REV. DATE : 2014.10.29
REV.NO : 1.0
4/ 11
IC approval
The host device must be labeled to display the Industry Canada certification number of the module.
Contains transmitter module IC: 2703H-DMWB1BH5
L di itif d' il d i t êt éti té ffi h l é d tifi ti d'I d t i C d d
L
e
di
spos
itif
d'
accue
il
d
o
i
ven
t
êt
re
éti
que
té
s pour a
ffi
c
h
er
l
e num
é
ro
d
e cer
tifi
ca
ti
on
d'I
n
d
us
t
r
i
e
C
ana
d
a
d
u
module.
Contient module émetteur IC : 2703H-DMWB1BH5
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the
following
two conditions: (1) this device may not cause interference, and (2) this device must accept any
interference,
including interference that may cause undesired operation of the device.
Cet appareil est conforme avec Industrie Canada exempts de licence standard RSS (s). L'opération est
soumise aux deux conditions suivantes: (1) cet appareil ne peut causer d'interférences, et (2) cet appareil
doit accepter toute interférence, y compris les interférences quipeuvent causer un mauvais
fonctionnement de l'appareil.
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type
and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio
interference to other users the antenna type and its gain should be so chosen that the equivalent
interference
to
other
users
,
the
antenna
type
and
its
gain
should
be
so
chosen
that
the
equivalent
isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec
une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada.
Dans le but de réduire les risques de brouillage radioélectrique à l'intention des autres utilisateurs, il faut
choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée quivalente (p.i.r.e.) ne
dépassepas l'intensité nécessaire à l'établissement d'une communication satisfaisante.
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum distance 20cm between the radiating element
of this device and the user.
NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE
CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS
COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.
Cet a
pp
areil est conforme aux limites d'ex
p
osition aux ra
y
onnements d'Industrie Canada
p
our un
pp p y p
environnement non contrôlé. Cet appareil doit être installé et utilisé à distance minimum de 20cm entre
l'élément rayonnant de cet appareil et l'utilisateur.
REMARQUE : LE FABRICANT N'EST PAS RESPONSABLE DES INTERFÉRENCES
RADIOÉLECTRIQUES CAUSÉES PAR DES MODIFICATIONS NON AUTORISÉES APPORTÉES À
CET APPAREIL. DE TELLES MODIFICATIONS POURRAIT ANNULER L'AUTORISATION ACCORDÉE
À L'UTILISATEUR DE FAIRE FONCTIONNER
L'APPAREIL
©2014 LGIT. All rights reserved.
User Manual
PAGE :
REG. DATE : 2014.10.29
MODEL: WB1BH5
REV. DATE : 2014.10.29
REV.NO : 1.0
5/ 11
4. Storage Conditions
Parameter Min Max Unit
Storage Temperature
-
10
+
80
℃
Storage
Temperature
10
80
℃
Storage Humidity (@ 40℃)-90 %
Caution : The specifications above the Table define levels at which permanent damage
to the device can occur Function operation is not guaranteed under these conditions
to
the
device
can
occur
.
Function
operation
is
not
guaranteed
under
these
conditions
.
Operating at absolute maximum conditions for extend periods can adversely affect the
long-term reliability of the device.
• Other conditions
1) Do not use or store modules in the corrosive atmosphere, especially where chloride
gas, sulfide gas, acid, alkali, salt or the like are contained.
Also, avoid exposure to moisture.
2) Store the modules where the temperature
and relative humidity do not exceed 5 to 40℃and 20 to 60%.
3) Assemble the modules within 6 months.
Check the soldering ability in case of 6 months over.
5. Operating Conditions
Parameter Min Typ Max Unit
Ambient Temperature 0 - +70 ℃
Operating Humidity (40℃)--85 %
Supply Voltage 3.15 3.3 3.45 Vdc
©2014 LGIT. All rights reserved.
User Manual
PAGE :
REG. DATE : 2014.10.29
MODEL: WB1BH5
REV. DATE : 2014.10.29
REV.NO : 1.0
6/ 11
6. Interface Specification
1) UART
Figure 11-1 shows the UART timing diagram. Table 11-1 lists the UART timing
characteristics Figure 11
2 shows the UART data frame Table 11
2 describes
characteristics
.
Figure
11
-
2
shows
the
UART
data
frame
.
Table
11
-
2
describes
the symbols used in Table 11-2.
[ Figure 11-1. UART Timing ]
[ Table 11-1. UART Timing Characteristics]
[ Figure 11-2. Data Frame]
©2014 LGIT. All rights reserved.
[ Table 11-2. Data Frame Key ]
User Manual
PAGE :
REG. DATE : 2014.10.29
MODEL: WB1BH5
REV. DATE : 2014.10.29
REV.NO : 1.0
7/ 11
2) PCM
Figure 11-3 shows the interface timing for the PCM. Table 11-3 and Table 11-4
Lists the associated master and slave parameters
Lists
the
associated
master
and
slave
parameters
.
[ Figure 11-3. PCM Interface Timing ]
[ Table 11-3. PCM Master ]
©2014 LGIT. All rights reserved.
[ Table 11-4. PCM Slave ]
User Manual
PAGE :
REG. DATE : 2014.10.29
MODEL: WB1BH5
REV. DATE : 2014.10.29
REV.NO : 1.0
8/ 11
7. Pin Description
< TOP View > < Bottom View >
1
2
Note.
1) Recommend a Module install sequence for prevent USB device failure
- Supply 3.3V power
C t t d t i l (UART TX RX)
1
2
©2014 LGIT. All rights reserved.
-
C
onnec
t
t
o
d
a
t
a s
i
gna
l
(UART
TX
,
RX)
2) Connector: 12Pin SMD Connector
A
User Manual
PAGE :
REG. DATE : 2014.10.29
MODEL: WB1BH5
REV. DATE : 2014.10.29
REV.NO : 1.0
9/ 11
8. Outline Drawing
©2014 LGIT. All rights reserved.
User Manual
PAGE :
REG. DATE : 2014.10.29
MODEL: WB1BH5
REV. DATE : 2014.10.29
REV.NO : 1.0
10 / 11
9. Packing Information
©2014 LGIT. All rights reserved.
User Manual
PAGE :
REG. DATE : 2014.10.29
MODEL: WB1BH5
REV. DATE : 2014.10.29
REV.NO : 1.0
11 / 11
©2014 LGIT. All rights reserved.