LG Electronics USA 9QK-LCF810 Car Audio User Manual BEJ9QK LCF810

LG Electronics USA Car Audio BEJ9QK LCF810

User manual

OWNER’S MANUALCAR CD/MP3/WMA ReceiverPlease read this manual carefully before operating your set and retain it for future reference.P/NO : MFL63287368LCS710BR / LCS710DAB / LCF810BR / LCF810DABENGLISH DEUTSCHFRANÇAISESPAÑOL ITALIANONEDERLANDS SLOVENŠČINA
Getting Started2Getting Started1Safety InformationCAUTIONRISK OF ELECTRIC SHOCK DO NOT OPENCAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.This lightning ash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product’s enclosure that may be of sucient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.WARNING: Do not install this equipment in a conned space such as a book case or similar unit.Always operate the vehicle in a safe manner. Do not become distracted by the vehicle while driving, and always be fully aware of all driving condition. Do not change settings, or any functions. Pull over in a safe and legal manner before attempting such operations.Do not use for many hours at extremely low or high temperature. (-10 °C to 60 °C)To reduce the risk of electric shock, do not remove the cover or back of this product. There are no user-serviceable parts inside. Refer servicing to qualied service personnel.To reduce the risk of re or electric shock, do not expose this product to dripping or splashing water, rain, or moisture.The temperature of unit’s outside can be extremely high, please use the unit after proper installation in your vehicle.This unit cannot play 8 cm disc (use 12 cm disc only).While driving, keep the sound volume at a proper level.Do not drop it and avoid heavy impacts at anytime. This unit is for vehicles with a 12-volt battery and negative grounding. Before installing it in a recreational vehicle, lorry or bus, check the battery voltage. To avoid shorts in the electrical system, be sure to disconnect the E battery cable before beginning the installation.
Getting Started 3Getting Started1CAUTION: This product employs a Laser System.To ensure proper use of this product, please read this owner’s manual carefully and retain it for future reference. Shall the unit require maintenance, contact an authorized service centre.Use of controls, adjustments or the performance of procedures other than those specied herein may result in hazardous radiation exposure.To prevent direct exposure to laser beam, do not try to open the enclosure. Visible laser radiation when open. DO NOT STARE INTO BEAM.“This device is equipped with a portable battery or accumulator. Safe way to remove the battery or the battery from the equipment: Remove the old battery or battery pack, follow the steps in reverse order than the assembly. To prevent contamination of the environment and bring on possible threat to human and animal health, the old battery or the battery put it in the appropriate container at designated collection points. Do not dispose of batteries or battery together with other waste. It is recommended that you use local, free reimbursement systems batteries and accumulators.” The battery shall not be exposed to excessive heat such as sunshine, re or the like.You have to set the disc format option to [Mastered] in order to make the discs compatible with the LG players when formatting rewritable discs. When setting the option to Live File System, you cannot use it on LG players.(Mastered/Live File System : Disc format system for Windows Vista) When being connected in a wrong way, the unit displays as follows.- Antenna port short : "EXTERNAL ON PORT SHORT CIRCUIT CHECK"After connecting it again, restart the unit. > CautionDisposal of your old appliance1. When this crossed-out wheeled bin symbol is attached to a product it means the product is covered by the European Directive 2002/96/EC.2. All electrical and electronic products shall be disposed of separately from the municipal waste stream via designated collection facilities appointed by the government or the local authorities.3. The correct disposal of your old appliance will help prevent potential negative consequences for the environment and human health.4. For more detailed information about disposal of your old appliance, please contact your city oce, waste disposal service or the shop where you purchased the product. LG Electronics hereby declares that this/ these product(s) is/are in compliance with the essential requirements and other relevant provisions of Directive 2006/95/EC and ECE Regulation 10.03 (3.2.9).European representative :LG Electronics Service Europe B.V. Veluwezoom 15, 1327 AE Almere, The Netherlands(Tel : +31-(0)36-547-8888)The unit is compatible with the steering wheel remote control. The function allows operation by sending the steering wheel remote control signal to the unit. For details, consult with your dealer.
Table of Contents412345Table of Contents1 Getting Started2 Safety Information5 Front panel [LCS710BR / LCS710DAB]6 Front panel [LCF810BR / LCF810DAB]7 Remote control7 – Battery Installation2 Connecting8 About detachable control panel [LCS710BR / LCS710DAB]8 – Attaching the control panel8 – Detaching the control panel9 About detachable control panel [LCF810BR / LCF810DAB]9 – Attaching the control panel9 – Detaching the control panel10 Installation10 – Basic Installation10 – Removing the existing receiver unit10 – ISO-DIN Installation11 Connection11 – Connecting to a car3 Operating12 Operation12 – Basic operations12 – Turning off the sound temporarily12 – Using EQ (Equalizer)12 – Checking the clock12 – Turning off the display light12 – Resetting the unit13 – Adjusting the general settings14 Listening to a CD14 – Pausing or restarting CD playback14 – Searching for a section within a track / file15 – Skipping to another track/ file15 – Checking information about your music15 – Playing back tracks / files in a way you want16 Listening to music from an external device16 – Preventing radical changes in volume as switching sources17 Listening to the TUNER17 – Storing desired frequencies manually17 – Listening to a preset station18 – Adjusting TUNER settings19 Listening to the DAB (Only LCS710DAB / LCF810DAB)19 – Storing desired frequencies manually19 – Listening to a preset station20 – Adjusting DAB settings21 Using an USB device / SD card21 – Moving to another drive21 – Quick Search of a desired file21 – Playable USB device / SD card Requirement21 – Recording to USB device / SD card22 Listening to music by connecting iPod / iPhone22 – Pausing or restarting playback22 – Searching for a section within a track / file22 – Checking information about your music23 – Playing back tracks / files in a way you want23 – Playing back files by music menus23 – Two way Control23 – Compatible iPod models24 Connecting a Bluetooth wireless technology25 – Using the buttons for Bluetooth wireless technology25 – Using a Bluetooth wireless technology27 – Adjusting the setting28 – Phone compatibility list4 Troubleshooting31 Troubleshooting5 Appendix32 Specifications
Getting Started 5Getting Started1Front panel [LCS710BR / LCS710DAB]abc d efg h ijklmnopqrstu va BEjects a disc.b 43$t0''- When pressed, selects function sources. - When pressed and held, powers unit on or o. c NPlays and pauses playback. Temporarily stops the sound.d Volume knobr"EKVTUTWPMVNFMFWFM r$POñSNTUIFTFUUJOHT r$IFDLTUSBDLTñMFTPSQSFTFUTUBUJPOTe FIn each mode, sets playback items. `Activates setting menu.f BAND- Selects a band in Tuner mode.- Moves to a next USB drive. t5"J10% - Searches stations that have TA / TP information, when it is pressed and held. - Activates Two way Control.g Remote Sensorh Display windowi 6 Opens the front panel.j RRecording to USB / SD card.k - Activates BT function. - Answers a call.l Returns to the previous step. Ends a call.m A / DSkip / Search / Seek / Tunen EQImproves sound quality. - When pressed, selects the EQ function.o %*41- Press it, you can check the clock time. - Press and hold it, you can turn on /o the display window and the light of LED buttons.p INTIntro scan.q 315Repeats playback.r 4)'Shues playback. s Numeric buttons (1 to 6)Selects a numbered preset station in TUNER.t AUXIf connected to other portable player, you can enjoy music from it on the unit.u USB portv SD card slot[Front unit detached panel]
Getting Started6Getting Started1Front panel [LCF810BR / LCF810DAB]abcdefghijklmnop qa 43$t0''- When pressed, selects function sources. - When pressed and held, powers unit on or o. b NPlays and pauses playback. Temporarily stops the sound.c Volume knob- Adjusts volume level. - Conrms the settings. - Checks tracks, les or preset stations.d FIn each mode, sets playback items. `Activates setting menu.e BAND- Selects a band in Tuner mode.- Moves to a next USB drive. t5"J10% - Searches stations that have TA / TP information, when it is pressed and held. - Activates Two way Control.f Display windowg Remote Sensorh 01&/Opens the front panel.i RRecording to USB / SD card.j - Activates BT function. - Answers a call.k Returns to the previous step. Ends a call.l A / DSkip / Search / Seek / Tunem EQImproves sound quality. - When pressed, selects the EQ function.n %*41- Press it, you can check the clock time. - Press and hold it, you can turn on /o the display window and the light of LED buttons.o AUXIf connected to other portable player, you can enjoy music from it on the unit.p USB port q SD card slot[Front unit detached panel]
Getting Started 7Getting Started1Remote controla 43$t0''r8IFOQSFTTFETFMFDUTGVODUJPOTPVSDFT r8IFOQSFTTFEBOEIFMEQPXFSTVOJUPíb '6/$When pressed, sets playback items in each mode.t.&/6 When pressed and held, activates setting menu.c BANDSelects a band in Tuner mode. DRV Moves to a next USB drive.d d/M Plays or pauses playback.e 4)'Shues playback.f .65&Temporarily stops the sound.g 70-6.&W / SAdjusts volume level.h c / vSkip / Search / Seek / Tune Returns to the previous step. w / sr-JTUVQEPXO r"EKVTUTTFUUJOHT r.PWFT.18."USBDLTCBDLXBSEPS forward if there is no folder or one folder on a CD. r.PWFTUPUIFQSFWJPVTPSOFYUGPMEFSJGUIFSF are more than 2 folders on a CD. ENTER / LIST r$POñSNTUIFTFUUJOHT r$IFDLTUSBDLTñMFTPSQSFTFUTUBUJPOTi %*41r1SFTTJUZPVDBODIFDLUIFDMPDLUJNF r1SFTTBOEIPMEJUZPVDBOUVSOPOPíUIF display window and the light of LED buttons.j 315Repeats playback.k INTIntro scan.l Numeric buttons (1 to 6)Selects a numbered preset station in TUNER.Battery Installation1. Pull out the battery holder with a sharp product like a ball point pen.2. Put the battery with and correctly on the battery holder.3. Push the battery holder back into its original position. yUse only one CR2025 (3 V) lithium battery. yRemove the battery if the remote control is not used for a long period of time. yDo not leave the product in a hot or humid place. yDo not handle the battery with metallic tools. yDo not store the battery with metallic materials. , Note
Connecting8Connecting2About detachable control panel [LCS710BR / LCS710DAB]Attaching the control panel1. Align the left side of the panel with the stopper.2. Push the right side of panel into the unit until it clicks. yThe control buttons may not work properly if the control panel is not attached properly. If this occurs, gently press the display. yDo not leave the control panel in any area exposed to high temperatures or direct sunlight. yDo not drop the control panel or otherwise subject it to strong impact. yDo not allow such volatile agents as benzine, thinner, or insecticides to come into contact with the surface of the control panel. > CautionDetaching the control panel1. Press the 6 to open the control panel.2. Push the control panel to right. 3. Pull the control panel out of the unit.4. Put the detached control panel into the protective case.Control panelProtective CasePeriodically wipe the contacts on the back of the control panel with a cotton swap moistened with alcohol. For safety, turn o the ignition before cleaning, and remove the key from the ignition switch. , Note
Connecting 9Connecting2About detachable control panel [LCF810BR / LCF810DAB]Attaching the control panel1. Attach part CA of the control panel to part CB of the unit.hi2. Attach part C of the control panel to part D of the unit while pushing the control panel to left.3. Close the control panel.jk yThe control buttons may not work properly if the control panel is not attached properly. If this occurs, gently press the display. yDo not leave the control panel in any area exposed to high temperatures or direct sunlight. yDo not drop the control panel or otherwise subject it to strong impact. yDo not allow such volatile agents as benzine, thinner, or insecticides to come into contact with the surface of the control panel. > CautionDetaching the control panel1. Press the OPEN to open the control panel.2. Push the control panel to left.3. Pull the control panel out of the unit.4. Put the detached control panel into the protective case.Control panelProtective CasePeriodically wipe the contacts on the back of the control panel with a cotton swap moistened with alcohol. For safety, turn o the ignition before cleaning, and remove the key from the ignition switch. , Note
Connecting10Connecting2InstallationBasic InstallationBefore installing, make sure that the ignition-switch is set to OFF and remove the terminal of the car battery to avoid short-circuiting.Bend the claws according to the thickness of the dashboard.Control panel1. Remove the existing receiver unit.2. Make the necessary connections. 3. Install the installation sleeve. 4. Install the unit into the installation sleeve.Removing the existing receiver unitIf there is already an installation sleeve for the receiver unit in the dashboard, it must be removed.1. Remove the rear support from the unit.2. Remove the control panel and trim ring from the unit.3. Insert the lever into the hole on one side of the unit. Perform the same operation on the other side and pull the unit out from the mounting sleeve.ISO-DIN InstallationControl panel1. Slide the unit into the ISO-DIN frame.2. Fit screws removed from the old unit.3. Slide the unit and frame into the dash opening.4. Install the dash panel or adapter plate. (According to models, this step may not be needed.)5. Install the trim ring to the unit.6. Install the control panel to the unit.
Connecting 11Connecting2ConnectionConnecting to a carBefore installing, make sure that the ignition-switch is set to OFF and remove the terminal of the car battery to avoid short-circuiting.abcdefghabcdefghabcdefghAAAAAAAAA a Gray : Front Right +A b Gray / Black Stripe: Front Right -A c Violet : Rear Right +A d Violet / Black Stripe: Rear Right -A e White : Front Left +A f White / Black Stripe: Front Left -A g Green : Rear Left +A h Green / Black Stripe: Rear Left -Power AntennaControl RelayTo Audio out To Audio inAmplierSub-woofer Left Sub-woofer Right Front Left Front Right Rear Left Rear RightAmplierB f Power Antenna (Blue)B g Dimmer (Pink)B c To Ignition (Red)B h Ground (-) (Black)B d To Battery (+) (Yellow)B e Remote On (Blue / White)B b Phone Mute (Orange)B a Not connectedDimmer SwitchIgnition SwitchWired remote input (Black): Hard-wired control adapter can be connected.(Optional / Not supplied) SMB type of DAB Antenna can be connected. (Only LCS710DAB / LCF810DAB)Sub-woofer
Operating12Operating3OperationBasic operations1. Turn the unit on by pressing any key on the unit.2. Select a source by pressing SRC.3. Rotate the volume knob to adjust the volume on the unit. Or press VOLUME W / S on the remote control.If a source is not connected to the unit, the source is not recognized. , NoteTurning off the sound temporarily1. Press to mute your unit.Or press MUTE on the remote control.2. To cancel it, press again.Or press MUTE again.Using EQ (Equalizer)EQ is to increase or decrease the signal strength of audio frequencies. The function helps you to enjoy sound more plentifully.Press EQ on the unit. And rotate the volume knob to select the item and press it. The indicator lights up in the following order.FLAT / XDSS+ / POP / CLASSIC / ROCK / JAZZ / VOCAL / SALSA / SAMBA / REGGAE / RUSSY / USER EQ1 / USER EQ2You can adjust sound level to your preference. Once you select a USER EQ1 / 2 mode and press and hold ` on the unit, then adjust the sound level ((BAS (bass), MID (middle), TRB (treble), BALANCE (left / right speaker), FADER (front / rear speaker), SW (Subwoofer), SW-F (Subwoofer Frequency), A-EQ (Auto EQ)), it will be automatically stored for the currently selected USER EQ1 / 2 mode. Refer to the "For [SOUND] setting" for USER EQ1 / 2 mode on the page 13. , NoteChecking the clock1. Press DISP to check the clock.2. Press it again to remove it. Turning off the display light1. Press and hold DISP.2. Press and hold it again to turn it on.Under the light-o condition, press any key, the light is turned on and then o automatically if you don't press it within a few seconds. , NoteResetting the unitYou can reset the unit when it does not operate properly.1. Detach the control panel.Refer to page 8 to 9 for detaching the control panel.2. Press the RESET hole with a sharp object. [LCS710BR / LCS710DAB] [LCF810BR / LCF810DAB]
Operating 13Operating3Adjusting the general settingsYou can adjust [SOUND], [LIGHT] and [OTHER] settings.On the unit1. Press and hold `.2. Rotate the volume knob to select [SOUND], [LIGHT], or [OTHER] and press it.3. Rotate the volume knob to select the item and press it.4. Rotate the volume knob clockwise or counterclockwise to adjust the level.5. Press the volume knob to conrm the setting. If you want to return to the previous step, press .On the Remote Control  1SFTTBOEIPME'6/$r.&/62. Press w / s to select [SOUND], [LIGHT], or [OTHER] and press ENTER.3. Press w / s to select the mode and press ENTER.4. Press w / s to adjust the level.5. Press ENTER to conrm the setting. If you want to return to the previous step, press .For [SOUND] settingYou can adjust sound quality by adjusting the level of BALANCE (left / right speaker), FADER (front / rear speaker), SW (Subwoofer), SW-F (Subwoofer Frequency) and A-EQ (Auto EQ).- When you set the EQ to USER EQ1 / 2 mode. : You can adjust the sound level of BAS (bass), MID (middle), TRB (treble), BALANCE (left / right speaker), FADER (front / rear speaker), SW (Subwoofer), SW-F (Subwoofer Frequency) and A-EQ (Auto EQ) ySW (Subwoofer) You can adjust the volume of subwoofer. ySW-F (Subwoofer Frequency) You can enable the subwoofer. SW OFF <-> SW 55 Hz <-> SW 85 Hz <-> SW 120 Hz. yA-EQ (Auto EQ) ON / OFF AUTO EQ operates only in the music le supported with genre in the device. When you set AUTO EQ to ON, POP, CLASSIC, ROCK, or JAZZ is automatically selected according to the music genre.For [LIGHT] settingYou can adjust the light eects by adjusting LED, DIM, or DIM L. yLED COL1 / COL2 / AUTO : You can change the LED window color. yDIM (Dimmer) OFF / ON / AUTO : You can change the brightness of the display window during the power-on status.Settings DescriptionDIM ON The display window becomes dark.DIM OFF The display window becomes bright.DIM AUTO The dimmer operates according to the car dimmer setting. yDIM L (Dimmer Level) : When you set DIM to ON / AUTO, you can adjust the dimmer level. (-2, -1, 0, +1, +2)
Operating14Operating3For [OTHER] setting yAUX (Auxiliary) ON / OFF It is possible to use auxiliary equipment with this unit. Activate the auxiliary setting when using auxiliary equipment connected to this unit. yDEMO OFF / ON You can change the initial indication on the display to information name (function name, EQ name, etc...) while listening to a source. yBEEP 2ND / ALL BEEP 2ND : The beep is generated when a key is pressed for longer than 2 seconds. BEEP ALL : The beep is generated when any key is pressed. yCLK (Clock) For the model RDS is not supported unit or even for a RDS supported unit.- When RDS CT information is not received and then you set CT to OFF, you can adjust the time by yourelf. Set the clock as follows ;1. Select a source to TUNER.2. Press the F to select the CT and then set CT to OFF. (Refer to the " Adjusting TUNER settings " on the page 18 for setting the CT (Clock Time) ON / OFF.)3. Press and hold ` on the unit to select [OTHER] and then select CLK by rotating the volume knob.4. Set the hour by rotating the volume knob.5. Press the volume knob to conrm the hour.6. Set the minute by rotating the volume knob.7. Press the volume knob to conrm the minute.- When RDS CT information is received ; The clock is displayed according to the RDS CT information.- When RDS is not supported, set the clock according to 3 to 7 steps.Listening to a CD[LCS710BR / LCS710DAB]1. Insert a CD.2. Rotate the volume knob on the unit to adjust the volume. Or press VOLUME W / S on the remote control.[LCF810BR / LCF810DAB]1. Press the OPEN to open the control panel.2. Insert a CD.3. Close the control panel.4. Rotate the volume knob on the unit to adjust the volume. Or press VOLUME W / S on the remote control.Make sure to press B after pressing OPEN to eject a disc. Refer to the picture above. , NotePausing or restarting CD playback1. Press N on the unit to pause playback.Or press d/M on the remote control.2. Press it to resume playback.Searching for a section within a track / file1. Press and hold A / D on the unit for about 1 second during playback. Or press and hold c / v on remote control.2. Press N on the unit at the point you want.Or press d/M on the remote control.
Operating 15Operating3Skipping to another track/ filePress A / D on the unit.Or press c / v on the remote control.Or1. Press the volume knob on the unit. Or press ENTER on the remote control.2. Rotate the volume knob on the unit to select a desired ROOT or folder and press it. Or press w / s and press ENTER on the remote control.3. Rotate the volume knob on the unit to select a desired track / le and press it.Or press w / s and press ENTER on the remote control.To skip to previous track, press briey A with- in 3 seconds of playing time. , NoteChecking information about your musicMP3 / WMA les often come with tags. The tag gives the Title, Artist or Album.Press DISP repeatedly during MP3 / WMA / CD TEXT le playback. If there is no information, "NO TEXT" will be shown in the display window.Playing back tracks / files in a way you wantFor using applicable buttons1. Press INT / RPT / SHF.2. Press it again to cancel.OrUsing the FUNC buttonOn the unit1. Press F.2. Rotate the volume knob to select an item and press it.3. Rotate the volume knob to select the option.4. Press the volume knob to set the option. If you want to return to the previous step, press .On the Remote Control1. Press FUNC tMENU.2. Press w / s to select an item and press it.3. Press w / s to select the option.4. Press ENTER to set the option. If you want to return to the previous step, press . yRPT (Repeat) The current selected tracks / les (1 RPT) or folder ( RPT) on the disc is played repeatedly. ySHF (Shue) Each les in the current selected folder ( SHF) or all of the tracks / les (SHF) on the disc is played randomly. During random playback, even if you press A, you won't go back to the previous track. yINT (Intro Scan) The rst 10 seconds of all tracks / les (INT) or each les in the current selected folder ( INT) on the disc are played. yDEV (Device) USB / SD You can change the recording device. USB <-> SD yMODE SPD REC / SPD COPY SPD REC : The recording speed is normal. And during the recording, you can listen to the music being recorded. SPD COPY : The recording speed is twice as fast. And during the recording, you can listen to the TUNER / DAB. But you cannot listen to the music being recorded.DEV and MODE are only available when the disc is activating. , Note
Operating16Operating3 y: The icon is displayed during MP3 / WMA playback. y.18."%JTDDPNQBUJCJMJUZXJUIUIJTunit is limited as follows:1. Sampling Frequency / 8 kHz to 48 kHz (MP3) 22.05 kHz to 48 kHz (WMA).2. Bit rate / within 8 kbps to 320 kbps (include VBR) (MP3) 32 kbps to 320 kbps (WMA).3. CD-R / CD-RW le system should be "ISO 9660".4. If you record MP3 / WMA les using software which cannot create a FILE SYSTEM, for example "Direct-CD" etc., it will not be possible to playback MP3 / WMA les. We recommend that you use "Easy-CD Creator" which creates an ISO 9660 le system.You have to set the disc format option to [Mastered] in order to make the discs compatible with the LG players when formatting rewritable discs. When setting the option to Live File System, you cannot use it on LG players.(Mastered / Live File System : Disc format system for Windows Vista)Customers should also note that permission is required in order to EPXOMPBE.18."öMFTBOENVTJDGSPNthe Internet. Our company has no right to HSBOUTVDIQFSNJTTJPO1FSNJTTJPOTIPVMEalways be sought from the copyright owner. , Note Listening to music from an external device1. Connect an external device to the AUX jack with line input cable.2. Select a source to AUX.3. Play the connected Auxiliary Equipment.4. Rotate the volume knob on the unit to adjust the volume. Or press VOLUME W / S on the remote control.Preventing radical changes in volume as switching sourcesOnly when you set AUX to ON as switching sources, you can adjust the volume level of each source to prevent radical changes in volume by selecting GAIN 0 / +3 / +6.1. Press F on the unit.Or press FUNC tMENU on the remote control.2. Rotate the volume knob on the unit. Or press w / s on the remote control to set the option. (GAIN 0 / +3 / +6)3. Press the volume knob on the unit. Or press ENTER on the remote control to conrm the setting. 4. If you want to return to the previous step, press .Or press on the remote control.
Operating 17Operating3Listening to the TUNER1. Press SRC repeatedly to select a source to TUNER.2. Press BAND repeatedly to select a desired band.3. For manual search, press and hold A / D on the unit until “MANUAL“ is displayed. Then press it repeatedly to select a desired frequency. Or press and hold c / v on the remote control. For auto search, press A / D on the unit until “SEARCH” is displayed. (Except MW) Or press c / v on the remote control.4. Rotate the volume knob on the unit to adjust the volume. Or press VOLUME W / S on the remote control.Storing desired frequencies manually1. Press BAND to select a desired band you want to store.2. Select the desired frequency by using A / D on the unit. Or use c / v on the remote control.3. Press the volume knob and rotate the volume knob to select a preset station among 1 to 6 and then press and hold the volume knob until the beep sound is heard. Or press ENTER and press w / s to select a preset station among 1 to 6 and then press and hold ENTER until the beep sound is heard on the remote control. Or press and hold one of preset buttons among 1 to 6 on the remote control until the beep sound is heard. Or press and hold one of preset buttons among 1 to 6 on the unit until the beep sound is heard. (Only LCS710BR / LCS710DAB)4. Repeat steps 1 to 3 to preset other stations.When a station is stored on the preset numbers on which another station of the same band has already been preset, the previously preset station is automatically erased. , NoteListening to a preset station1. Press BAND repeatedly to select a desired band.2. Press the volume knob on the unit. Or press ENTER on the remote control.3. Rotate the volume knob to select a preset station. Or press w / s on the remote control.4. Press the volume knob. Or press ENTER on the remote control. OrPress BAND and then press the desired preset button among 1 to 6 on the remote control.Or press BAND and then press the desired preset button among 1 to 6 on the unit. (Only LCS710BR / LCS710DAB)
Operating18Operating3Adjusting TUNER settingsOn the unit1. Press F.2. Rotate the volume knob to select an item and press it.3. Rotate the volume knob to set the option and press it.4. If you want to return to the previous step, press .On the Remote Control1. Press FUNC tMENU.2. Press w / s to select an item and press ENTER.3. Press w / s to set the option and press ENTER.4. If you want to return to the previous step, press . yPTY (Program type, RDS (OPTIONAL)) It searches the radio stations by program type of FM tuner. The program types are displayed as follows.NEWS FINANCE EASY MAFFAIRS CHILDREN LIGHT MINFO SOCIAL CLASSICSSPORT RELIGION OTHER MEDUCATE PHONE IN JAZZDRAMA TRAVEL COUNTRYCULTURE LEISURE NATION MSCIENCE DOCUMENT OLDIESVARIED POP M FOLK MWEATHER ROCK M yA / S (Auto Store) The six strongest broadcasting frequencies will be stored under preset button 1 to 6 in the order of their signal strength. To cancel, press the volume knob (or ENTER on the remote control). yP / S (Preset scan) Each preset station appears. To cancel, press the volume knob (or ENTER on the remote control). ySENS (Tuner sensitivity) MID / HI / LOW In an area in which signal reception is weak, it helps the tuner to search more stations. The weaker the reception is, the lower option you should set to.RDS (OPTIONAL) yAF (Alternative Frequency) ON / OFF When the reception quality drops, the tuner automatically changes to another station in the network, broadcasting a better reception quality, using the PI and AF codes. yREG (Region) ON / OFF REG ON : The unit switches to another station, within the same network, broadcasting the same program when the receiving signals from the current station become weak. REG OFF : The unit switches to another station, within the same network when the receiving signals from the current station become weak. (In this mode, the program may dier from the one currently received.) yTA (Trac Announcement) ALARM / SEEK TA ALARM : When the tuned station has no TP information for 5 seconds, a double beep sound is output. TA SEEK : When the tuned station does not receive TP information for 5 seconds, the receiver retunes to the next station that has the TP information. yPI (Programme Identication) SOUND / MUTE PI SOUND : When the frequency of a tuned station switches to an AF (Alternative frequency) with an unidentied PI, it keeps the sound. PI MUTE : When the frequency of a tuned station switches to an AF with an unidentied PI, it mutes the sound until the PI is identied. yCT (Clock Time) ON / OFF You can use the RDS CT information to update the time. When RDS CT information is not received and then you set CT to OFF, you can adjust the time by yourself. Refer to the page 14 for setting the clock.
Operating 19Operating3Listening to the DAB (Only LCS710DAB / LCF810DAB)1. Press SRC repeatedly to select a source to DAB.2. Press BAND repeatedly to select a desired band.3. Press the volume knob on the unit. Or press ENTER on the remote control.4. Rotate the volume knob to select a station. Or press w / s on the remote control.5. Press the volume knob. Or press ENTER on the remote control.6. Press A / D on the unit to skip to another station. Or press c / v on the remote control. For auto search, press and hold A / D on the unit until “ENS SRCH” (Ensemble Search) is displayed. Or press and hold c / v on the remote control.7. Rotate the volume knob on the unit to adjust the volume. Or press VOLUME W / S on the remote control.Storing desired frequencies manually1. Press BAND to select a desired band you want to store.2. Select the desired frequency by using A / D on the unit. Or use c / v on the remote control.3. Press and hold the volume knob and rotate the volume knob to select a preset station among 1 to 6 and then press and hold the volume knob until the beep sound is heard. Or press and hold ENTER and press w / s to select a preset station among 1 to 6 and then press and hold the ENTER until the beep sound is heard on the remote control. Or press and hold one of preset buttons among 1 to 6 on the remote control until the beep sound is heard. Or press and hold one of preset buttons among 1 to 6 on the unit until the beep sound is heard. (Only LCS710DAB)4. Repeat steps 1 to 3 to preset other stations.When a station is stored on the preset numbers on which another station of the same band has already been preset, the previously preset station is automatically erased. , NoteListening to a preset station1. Press BAND repeatedly to select a desired band.2. Press and hold the volume knob on the unit. Or press ENTER on the remote control.3. Rotate the volume knob to select a preset station. Or press w / s on the remote control.4. Press the volume knob. Or press ENTER on the remote control. OrPress BAND and then press the desired preset button among 1 to 6 on the remote control.Or press BAND and then press the desired preset button among 1 to 6 on the unit. (Only LCS710DAB)
Operating20Operating3Adjusting DAB settingsOn the unit1. Press F.2. Rotate the volume knob to select an item and press it.3. Rotate the volume knob to set the option and press it.4. If you want to return to the previous step, press .On the Remote Control1. Press FUNC tMENU.2. Press w / s to select an item and press ENTER.3. Press w / s to set the option and press ENTER.4. If you want to return to the previous step, press . yPTY (Program type, RDS (OPTIONAL)) The program types are displayed as follows. When you select an item, it will start operating immediately.NEWS FINANCE EASY MAFFAIRS CHILDREN LIGHT MINFO SOCIAL CLASSICSSPORT RELIGION OTHER MEDUCATE PHONE IN JAZZDRAMA TRAVEL COUNTRYCULTURE LEISURE NATION MSCIENCE DOCUMENT OLDIESVARIED POP M FOLK MWEATHER ROCK M yA-SCAN (Auto Scan) Scans all available services. To conrm the lists, press the volume knob and rotate the volume knob. yP-SCAN (Preset Scan) The broadcasting frequencies stored in the preset number are received Sequentially. Each broadcasting frequencies are received for 6 seconds. yDRC (Dynamic Range Control) ON / OFF Automatically adjusts the audio level. yANNOUNCE (Announcement) X / O Provides information on selected contents. TRFC (Trac), TRNSP (Transport), WARN (Service Warning), NEWS, WTHR (Weather), EVNT (Event), SEVNT (Special Event), PINFO (Program Info), SPORT (Sport Report), FNNC (Financial Report) yLINK DAB+FM / OFF / DAB / FM When the reception quality drops, the tuner automatically changes to another station in the network. If the broadcasting is disconnected during operation, it does not sound until the next broadcasting is linked. It takes about 10 seconds. Depending on the amount of broadcasting information, it can be shorter or longer.If each preset number has no stored frequency, "EMPTY" is displayed. , Note
Operating 21Operating3Using an USB device / SD card[USB]1. Open the USB cover.2. Connect the USB device.3. Press SRC repeatedly to select a source to USB.4. Rotate the volume knob on the unit to adjust the volume. Or press VOLUME W / S on the remote control.[SD]1. Detach the control panel. (Refer to "About detachable control panel" on page 8 to 9.)2. Connect the SD card. 3. Attach the control panel.4. Press SRC repeatedly to select a source to SD.5. Rotate the volume knob on the unit to adjust the volume. Or press VOLUME W / S on the remote control. [LCS710BR / LCS710DAB] [LCF810BR / LCF810DAB]Moving to another driveWhen connecting this unit to multi-reader, press BAND on the unit (or DRV on remote control) to go the next drive. Each time you press the button, the driver modes change.Quick Search of a desired fileYou can select and play a desired le regardless of the order in USB device / SD card.1. Press the volume knob on the unit. Or press ENTER on the remote control.2. Rotate the volume knob on the unit to select a desired ROOT or folder and press it. Or press w / s and press ENTER on the remote control.3. Rotate the volume knob on the unit to select a desired track / le and press it.Or press w / s and press ENTER on the remote control.Other functions are same with "Listening to a CD". Refer to page 14 to 15. , NotePlayable USB device / SD card Requirement yDo not extract the USB device / SD card during operation (play, etc.). yAn USB device / SD card which requires additional programme installation when you have connected it to a computer, is not supported. yRegular back up is recommended to prevent data loss. yIf you use a USB extension cable, USB HUB, USB Multi-reader, or external HDD, the USB device may not be recognized. yWhen you connect a partitioned USB device into the unit, only the rst partition is recognized on it. ySome USB device may not work with this unit. yDigital camera and mobile phone are not supported. yUSB Port of the unit cannot be connected to PC. The unit cannot be used as a storage device. yUsing FAT (16 / 32) le system is supported. Using NTFS le system is supported to read only.Recording to USB device / SD card[USB]1. Open the USB cover and connect it to the unit. 2. Select one of the following lists. (CD, FM tuner, DAB, Bluetooth Handsfree)3. Press R to start recording.For one track CD recoridng, press it once. For all tracks recording, press and hold it until the beep is heared. (In case of MP3 / WMA CD, recorded all les in the folder.)4. Press it again to stop.
Operating22Operating3[SD]1. Detach the control panel and connect it to the unit. Then attach the control panel. (Refer to "About detachable control panel" on page 8 to 9.)2. Select CD only.3. Press R to start recording.For one track CD recoridng, press it once. For all tracks recording, press and hold it until the beep is heared. (In case of MP3 / WMA CD, recorded all les in the folder.)4. Press it again to stop. y[USB] Only in CD, FM tuner, DAB and Bluetooth Handsfree, recording is available. [SD] Only in CD, recording is available. yDo not remove the USB device / SD card during recording, or an incomplete le may be made and not deleted on PC. yWhen USB device / SD card is not connected, "NO USB" / "NO SD" [LCS710BR / LCS710DAB] "REC ERR NO USB" / "REC ERR NO SD" [LCF810BR / LCF810DAB] displays and cannot record. yWhen USB device / SD card memory is full, "MEMORY FULL" [LCS710BR / LCS710DAB] "REC ERR MEMORY FULL" [LCF810BR / LCF810DAB] displays and stops recording. yWhile FM tuner / DAB / Bluetooth Handsfree recording, the broadcastings are recorded as a le every 20 minutes. yWhile one track CD recording, "REC 1" appears. While other recording, "REC" appears. yYou can adjust the recording speed. (Refer to the page 15.) , NoteThe making of unauthorized copies of copy-protected material, including computer programs, les, broadcasts and sound recordings, may be an infringement of copyrights and constitute a criminal oense. This equipment should not be used for such purposes.Be responsible Respect copyrightsListening to music by connecting iPod / iPhoneYou can enjoy iPod / iPhone-stored music on the unit by connecting it to the USB connector using the appropriate cable. [LCS710BR / LCS710DAB] [LCF810BR / LCF810DAB]1. Open the USB cover.2. Connect the iPod / iPhone.3. Press SRC to select a source to USB.4. Rotate the volume knob to adjust the volume on the unit. Or press VOLUME W / S on the remote control.Refer to the page 23 to check the compatible iPod model for this unit. , NotePausing or restarting playback1. Press N on the unit to pause playback.Or press d/M on the remote control.2. Press it to resume playback.Searching for a section within a track / fileDuring playback, press and hold A / D and then release at a point you want.Checking information about your musicMP3 / WMA les often come with tags. The tag gives the Title, Artist or Album.Press DISP repeatedly during MP3 / WMA le playback. If there is no information, "NO TEXT" will be shown in the display window.
Operating 23Operating3Playing back tracks / files in a way you wantOn the Unit1. Press F.2. Rotate the volume knob to select an item and press it.3. Rotate the volume knob to select the option.4. Press the volume knob to set the option. If you want to return to the previous step, press .On the Remote Control1. Press RPT / SHF.2. Press it again to cancel.Or1. Press FUNC tMENU.2. Press w / s to select an item and press ENTER.3. Press w / s to select the option.4. Press ENTER to set the option. If you want to return to the previous step, press . yRPT (Repeat) The current selected tracks / les (1 RPT) or folder ( RPT) on the iPod / iPhone is played repeatedly. ySHF (Shue) Each le in the currently selected album ( SHF) or all of the tracks / les (SHF) on the iPod / iPhone are played randomly. During random playback, even if you press A, you won't go back to the previous track. ySPD (BOOK SPEED) You can adjust the audiobook speed of iPod / iPhone to NOR (Normal), FAST or SLOW.Playing back files by music menusYou can check les by music menus and play it back. The music menus are as follows.PLAYLISTS / ARTISTS / ALBUMS / GENRES / SONGS / COMPOSER / AUDIO BOOK / PODCAST / ...1. Press the volume knob on the unit. Or press ENTER on the remote control.2. Rotate the volume knob on the unit to select a music menu and press it. Or press w / s on the remote control.3. Rotate the volume knob on the unit to select a le.Or press w / s on the remote control.4. Press the volume knob on the unit to conrm the setting.Or press ENTER on the remote control.5. If you want to return to the previous step, press . Or press on the remote control. Two way ControlYou can control on the unit and iPod / iPhone. yPress t5"J10% on the unit. Then playback is paused. And you can control on the unit and iPod / iPhone. yWhile using the Two way Control, any functions are not available on the unit. yPress t5"J10% again to cancel the Two way Control.Compatible iPod modelsiPod classic (5th / 6th generation) iPod nano (1st / 2nd / 3rd / 4th / 5th generation) iPod touch (1st / 2nd / 3rd generation) iPhone iPhone 3G iPhone 3GS iPhone 4We recommend that you use the OS Version 4.2.1 or more.
Operating24Operating3“Made for iPod” means that an electronic accessory has been designed to connect specically to iPod and has been certied by the developer to meet Apple performance standards. “Works with iPhone” means that an electronic accessory has been designed to connect specically to iPhone and has been certied by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards. iPod is a trademark of Apple Inc., registered in the U.S. and other countries. iPhone is a trademark of Apple Inc. Connecting a Bluetooth wireless technologyBefore you start the pairing procedure, make sure the Bluetooth wireless technology is turned on in to your phone. Refer to your phone’s user guide. Pairing links your unit and phone with Bluetooth wireless technology, and is required only once for the initial setup. If the connection is successful, the phone is registered (Device 1 to 10) and the ashing of indicator stops on the unit. The process of pairing may be dierent depend on the phones. The PIN CODE is 1234.ON PLAYER1. Enter the menu.2. Find the “CONNECT” menu. Rotate the volume knob3. Search the phones supported Bluetooth wireless technology.Press the volume knob4. Select a phone you want to connect.Rotate the volume knob5. Connect the phone. Press the volume knob6. Select the “CONNECT” menu. Press the volume knobUnit has a built-in microphone. [LCS710BR / LCS710DAB] [LCF810BR / LCF810DAB]
Operating 25Operating3Using the buttons for Bluetooth wireless technologyabcda Volume knobr1SFTTUIFWPMVNFLOPC(PUPUIFOFYUcontents of the setting.r3PUBUFUIFWPMVNFLOPC.PWFUIFDPOUFOUTvertically on the setting or choose a spell when you write the words on the unit. b r1SFTTJUUPFOUFS#5GVODUJPOr"OTXFSTBDBMMc r3FUVSOTUPUIFQSFWJPVTTUFQ Ends a call.d A / DAdjusts the mic volume while talking on the phone by BT function.rA : Press it to delete a spell or go back previous contents. Press more 1 second to delete all words entered on display when you write some words on the unit.rD : When you write some words on the unit, press it to move next space on display.Using a Bluetooth wireless technologyDisconnecting a phoneGo to the menu ( -> CONNECT -> LIST -> Connected device name -> DISCONN).Answering and Ending a callWhen your unit rings, press to answer a call.To end a call, press .Rejecting a callWhen your unit rings, press .Making a call saved as a preset numberPress and a preset number (1 to 6).Checking missed calls When an incoming call is not answered, the missed call message is displayed on the display window (without headset prole). When the “ ? ” appears, go to the menu ( -> CALL -> LASTCALL). You can check the list of missed call. To place a call, press . And to end the call and hang up the phone, press . yThe lists of LAST CALL are sorted from newest to oldest entries. yWhen you want to make an international call, press D to add “+” and to delete it press again. y“+” can only be added when the detail list of LASTCALL is selected. yRejecting a call / Making a call saved preset number / Missed call notication (These features are only available on phones with Headset / Handsfree prole.) yYou can record the Bluetooth Handsfree to USB. (Refer to the page 21 to 22.) , Note
Operating26Operating3Saving call numbers in the latest callsYou can easily save up to 6 phone numbers in the latest calls. Go to the menu (CALL -> LASTCALL -> Rotate the volume knob to select the phone number you want to save -> SAVE -> select 1 to 6).Audio transferIt is possible to switch the audio connection between your phone equipped with Bluetooth wireless technology and this unit.1. Press to answer the call.2. Press again. The “PRIVATE” is displayed.If the private mode is selected on the unit, press to return to the call to hands-free mode.Paring your unit and device with Bluetooth wireless technology (MP3 Player, MP3 Phone...)When you activate your Bluetooth device’s linked unit, you can listen to MP3 with wireless connections. The method of use for a Bluetooth device is the same as when using a Bluetooth phone. Refer to the phone’s user guide for using this function.Playing MP3 filesWhen you turn Bluetooth on, your device supported Bluetooth wireless technology displays “Bluetooth” on the home screen. The Bluetooth remains on until you turn the device o. Press SRC repeatedly to select “BT Music”. To play an MP3 le stored on your device. Refer to the phone’s user guide for using this function. This feature is only available on phones with A2DP(Advanced Audio Distribution Prole).Bluetooth wireless technology profiles informationIn order to use Bluetooth wireless technology, devices must be able to interpret certain proles. This unit is compatible with following proles.GAP (Generic Access Prole)HFP (Hands Free Prole)HSP (Hands Set Prole)GAVDP (Generic Audio / Video Distribution Prole)A2DP (Advanced Audio Distribution Prole)AVRCP (Audio / Video Distribution Remote Control Prole)OPP (Object Push Prole)PBA / PBAP (Phone Book Access Prole)WICS (Wireless Controller & Synchronization)You can control the unit by using the "WICS" application.1. Search the “WICS” application and install it. [Displays installed "WICS" application]2. Pairing links your unit and iPhone with Bluetooth wireless technology. (Refer to the page 24.)3. When you run the “WICS” application, activating source is displayed after initial screen. Then you can control the unit on iPone. [Initial screen] [Tuner screen]
Operating 27Operating3Adjusting the setting1. Press .2. Rotate the volume k nob to selec t an item and press it.3. Rotate the volume knob to set the option and press it.4. If you want to return to the previous step, press .CALL yLASTCALL Phone number list (received, dialed, missed). To call the phone number, select the phone number and press .To save it, select the phone number and press the volume knob. "SAVE" will be shown. Press the volume knob again. Rotate the volume knob to select a preset number (1 to 6). Press the volume knob again. The phone number be saved. yDIAL Enters the number directly on the unit. To select the 0 to 9 rotate the volume. Press D to make the phone number. To call it, Press . yPRESET Checks and deletes the phone number saved preset number. To delete the phone number, select the preset number by rotating the volume knob. And then press the volume knob. Press the volume knob again when the “DELETE” is displayed. P-BOOK yLIST Checks the list of the phone numbers saved by phonebook. ySEARCH Searches the phone number in the list. (English and Russian only) yGET Getting the phonebook from the phone automatically. This menu is only available on phones with PBA / PBAP (Phone Book Access Prole). yADD P-BOOK -> ADD -> Press the volume knob -> "000/500" will be displayed. Then send the phonebook data from your phone. Depend on your phone, the sending process is dierent. Refer to your phone's guide. This menu is only available on phones with OPP (Object Push Prole).CONNECT yLIST Checks the list of the Connected Device Name. ySEARCH Searches the phones available to connect. The Connected Device Name is displayed on the top. SETUP yVISIBLE Makes it is impossible to search this unit. (SHOWN <-> HIDDEN) yAUTO CONAdjusts connection with automatically or not. (ON <-> OFF) yAUTO ANS Adjusts answering automatically or not. (AUTO <-> MANUAL) yMIC VOL Adjusts microphone volume on the phone from 1 to 5. While you are on the phone with Bluetooth wireless technology, rotate the volume knob to adjust the MIC volume. yREDIAL Adjusts the counts of redial. (1 TIME <-> 2 TIMES)INFO yNAME Changes the name of this unit. yADDRESS Checks the address. yPIN-CODE Changes the PIN code. Default is 1234.
Operating28Operating3Phone compatibility listBluetooth list and manufacturing H : Hnadsfree P : Phonebook Sync (GET)company applicable. A : Audio Streming (A2DP) V : Object Push (Vcard, ADD)Company List H A P V Company List H A P V Company List H A P VNokia 32303250365053006021610361206131623062706280630065006600663066506670668066816820737073807610765076008600880095003650 (Italy)5500 SPORT6230i6820a7500prism7650 (Italy)8910i9300lE50E51E60E61E62OOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOONokia E70E71E73E90N70N71N73N77N80N82N90N91N92N93N95N-GageN-Gage QDE63N72N97N81N85N86 8MPN95N965530531053205800i58006120C6303C26306110 Navigator6288E65E75OOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOMotorola E398E550E680E680iKRZR K1L72RAZR V3RAZR V3iRAZR V3XRAZR V9RIZR Z3RIZR Z8ROKR E2ROKR E6SLVR L7U6V195V360V3ROHSV500V525V600A1600A1890V8A1200V6W510OOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOSONYERICSSONK610iK618iK700iK750iK770iK800iK850iM600iP1iP990iS500iS700iT610OOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOMotorola A1000A780E1000E1070OOOOOOOOOOO
Operating 29Operating3Bluetooth list and manufacturing H : Hnadsfree P : Phonebook Sync (GET)company applicable. A : Audio Streming (A2DP) V : Object Push (Vcard, ADD)Company List H A P V Company List H A P V Company List H A P VSONYERICSSONT68iV600V800W550iW710iW800iW810iW850iW980iZ1010Z600W300W880W910Z610OOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOSAMSUNG G600i900L600U600U700Z170T509OOOOOOOOOOOOOOOOOOOOLG CU500KE970KG245KG800U880U890M4410KF600KE850 PradaKG290KE500KM500KU990 ViewtyKU580KU970KU960U370KE770GD900KF900 PradaKC910 RenoirKM900 ArenaKS10KU250OOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOSIEMENS EF81S55S65S88SD65SL75SX1SXG75OOOOOOOOOOOOOOOOOOOSAMSUNG D500D600D820D900E770E900i600T509X820Z540VA707(SYNC)S5230D900i8910S8003S8300E950F210F300OOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOBLACKBERRY88008100(PEARL)8707vBOLD 9000Curve 8310OOOOOOOOOOOOOHP HW6915iPAQ h6315OOOOONEC N750N930OOPALM Treo750v O O OPHILPS O2 Xda Atom O O OSAGEM MYX6-2 OSHARP GX15GX25OOOOApple iPoneiPone 3GiPone 3GSOOOOOOl-MATE K-JAM O OPANTECH PG-6200PG-8000OOOOOHTC TouchTouch ProOOOOOO yWhen the phone features <Bluetooth Power Save> function, you should make the function turned on to maintain connection. yWhen you switch the call mode from handsfree to phone, the connection may be disconnected. ySome phones don’t support Reject function. yLow battery in phone may cause the problems. , Note
Operating30Operating3“The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by LG Electronics is under license. Other trademarks and trade names are those of their respective owners.”Bluetooth® wireless technology is a system which allows radio contact between electronic devices within a max range of 10 meters.Connecting individual devices under Bluetooth® wireless technology does not incur any charges. A mobile phone with Bluetooth® wireless technology can be operated via the Cascade if the connection was made via Bluetooth® wireless technology.operating condition for using a Bluetooth wireless technology function yClose windscreen. yTurn o the air conditioner / heater. yStop the vehicle or drive at low speed. yMake the call in a quiet location.- There may be dierences in call quality depending on phone type, road conditions weather, etc.- Using the phone while driving may cause unexpected accidents.- The Bluetooth wireless technology function may not operate properly with certain types of phones equipped with Bluetooth wireless technology.
Troubleshooting 31Troubleshooting4TroubleshootingSymptoms Cause SolutionPower doesn't turned on.The unit doesn't operate.Leads and connectors are not properly.Conrm once more that all connections are correct.The fuse is blown. Rectify the problem that caused the fuse to blow, and then replace it. Be very sure to install the correct fuse with the same rate.Noise and other factors are causing the built in microprocessor to operate incorrectly.Turn the unit o and then on again.No sound is heard. Cables are not connected correctly.Connect the cables correctly.There's audio skipping. This unit is not rmly secured. Secure this unit rmly.The playback is not possible. The disc is dirty. Clean the disc.The disc of unplayable type is loaded. Check what type the disc.Radio stations cannot be tuned in.The signal strength of the stations is too weak. (When tuning in with automatic tuning.)Tuned in the stations manually.No station has been preset or preset stations have been cleared. (When tuning by scanning preset stations.)Preset the stations. (Refer to the page 17.)iPod/ iPhone does not work. Check whether iPod / iPhone is connected to the unit correctly.Connect it to the unit correctly.The unit does not operate correctly even when the appropriate remote control buttons are pressed.Battery power is low. Load a new battery.
Appendix32Appendix5SpecificationsGeneralOutput Power : 53 W x 4 CH (Max.)Power Source : DC 12 VSpeaker impedance : 4 ΩGround System : NegativeDimensions (W x H x D) : (178 x 50 x169) mm (without Control Panel)Net Weight : 1.37 kgTUNERFM Tuning Range : 87.5 MHz to 108.0 MHz S / N Ratio : 55 dB Distortion : 0.7 % Usable Sensitivity : 12 dBμVAM (MW) Tuning Range : (520 to 1720) kHz or (522 to 1620) kHz S / N Ratio : 50 dB Distortion : 1.0 % Usable Sensitivity : 28 dBμVDABDistortion : 0.1 %Channel Separation (1 kHz) : 68 dBCDFrequency Response : 20 Hz to 20 kHzS / N Ratio : 80 dBDistortion : 0.12 %Channel Separation (1 kHz) : 55 dBAUXFrequency Response : 20 Hz to 20 kHzS / N Ratio : 80 dBDistortion : 0.1 %Channel Separation (1 kHz) : 45 dBMax Input Level (1 kHz) : 1.1 VUSBVersion : USB 1.1 or USB 2.0 Full SpeedBus Power Supply (USB) : DC 5 V 1 ASDDistortion : 0.1 %Line OUT Frequency Response : 20 Hz to 20 kHzOutput Voltage : 2 V (Max.)Subwoofer Frequency Response : 20 Hz to 120 HzOutput Voltage : 2 V (Max.) yDesign and specications are subject to change without notice.
Federal Communications Commission(FCC) Statement You are cautioned that changes or modifications not expressly approved by the part responsiblefor compliance could void the users authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules.These limits are designed to provide reasonable protection against harmfulinterference in a residential installation. This equipment generates, uses and can radiate radio frequency energyand, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.If this equipment does cause harmful interference to radio or television reception,which can be determined by turning the equipment off and on,the user is encouraged to try to correct the interference by one or more of the following measures:--. Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that towhich the receiver connected Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules.Operation is subject to the following two conditions:1) this device may not cause harmful interference, and) this device must accept any interference received, including interference 2that may cause undesired operation of the device. FCC RF Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for anuncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. End users must follow the specific operation instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating ing conjunction with any other antenna or transmitter.

Navigation menu